(1/14)

SERVICING SPECIFICATIONS
(1) ENGINE BODY
Item Factory Specification Allowable Limit
Lubricating oil capacity D1503-M-E2B 7.0 L
D1703-M-E2B 1.85 U.S.gals.
D1803-M-E2B 1.54 lmp.gals.
Oil pan depth
124 mm (4.88 in.) V2003-M-E2B
9.5 L
V2003-M-T-E2B
2.51 U.S.gals.
V2203-M-E2B
2.09 lmp.gals.
V2403-M-E2B
D1503-M-E2B 5.6 L
D1703-M-E2B 1.48 U.S.gals.
D1803-M-E2B 1.23 lmp.gals.
Oil pan depth
90 mm (3.54 in.) V2003-M-E2B
7.6 L
V2003-M-T-E2B
2.01 U.S.gals.
V2203-M-E2B
1.67 lmp.gals.
V2403-M-E2B
Cylinder head surface

0.05 mm / 500 mm
Flatness All models
0.0020 in. / 19.69 in.

Compression pressure

3.53 to 4.02 MPa / 290 min-1 (rpm) 2.55 MPa / 290 min-1 (rpm)
All models 36 to 41 kgf/cm2 / 290 min-1 (rpm) 26 kgf/cm2 / 290 min-1 (rpm)
512 to 583 psi / 290 min-1 (rpm) 370 psi / 290 min-1 (rpm)

Top clearance

0.55 to 0.70 mm
All models
0.0217 to 0.0276 in.

Valve clearance (When cold)

0.18 to 0.22 mm
All models
0.0071 to 0.0087 in.

KiSC issued 09, 2007 A

 (2/14)

Item Factory Specification Allowable Limit

Valve & valve seat Face angle (A) 1.047 rad.
(Intake) All models
60°
Face angle (A) 0.785 rad.
(Exhaust) All models
45°
Seat angle (B) 1.047 rad.
(Intake) All models
B 60°
C Seat angle (B) 0.785 rad.
A (Exhaust) All models
45°
Seat width (C) 2.12 mm
(Intake) All models
0.0835 in.
Seat width (C) 2.12 mm
(Exhaust) All models
0.0835 in.
Valve stem to valve guide
0.040 to 0.070 mm 0.1 mm
Clearance All models
0.00157 to 0.00276 in. 0.0039 in.

7.960 to 7.975 mm
Valve stem O.D. All models
0.31339 to 0.31398 in.

8.015 to 8.030 mm
Valve guide I.D. All models
0.31555 to 0.31614 in.

Valve recessing

0.05 mm (Protrusion) to
0.15 mm (Recessing) 0.4 mm (Recessing)
All models
0.0020 in. (Protrusion) to 0.0157 in. (Recessing)
0.0059 in. (Recessing)

Valve spring
41.7 to 42.2 mm 41.2 mm
Free length (A) All models
1.6417 to 1.6614 in. 1.6220 in.
B
1.0 mm
Tilt (B) All models
0.039 in.
A
117.6 N / 35.0 mm 100.0 N / 35.0 mm
Setting load / 12.0 kgf / 35.0 mm 10.2 kgf / 35.0 mm
Setting length All models
26.4 lbs / 1.3780 in. 22.5 lbs / 1.3780 in.

KiSC issued 09, 2007 A

 (3/14)

Item Factory Specification Allowable Limit

Valve timing 0.14 rad. before T.D.C.
D1503-M-E2B
8° before T.D.C.
T.D.C. D1703-M-E2B
I.O. E.C. D1803-M-E2B 0.21 rad. before T.D.C.
Open V2003-M-E2B
(Intake valve) V2203-M-E2B 12° before T.D.C.
V2403-M-E2B
0.35 rad. before T.D.C.
V2003-M-T-E2B
20° before T.D.C.
0.35 rad. after B.D.C.
D1503-M-E2B
20° after B.D.C.
D1703-M-E2B
D1803-M-E2B 0.63 rad. after B.D.C.
Close V2003-M-E2B
(Intake valve) V2203-M-E2B 36° after B.D.C.
E.O.
I.C. V2403-M-E2B
B.D.C. 0.79 rad. after B.D.C.
V2003-M-T-E2B
45° after B.D.C.
1.05 rad. before B.D.C.
D1503-M-E2B
60° before B.D.C.
D1703-M-E2B
D1803-M-E2B 1.05 rad. before B.D.C.
Open V2003-M-E2B
(Exhaust valve) V2203-M-E2B 60° before B.D.C.
V2403-M-E2B
0.96 rad. before B.D.C.
V2003-M-T-E2B
55° before B.D.C.
0.21 rad. after T.D.C.
D1503-M-E2B
12° after T.D.C.
D1703-M-E2B
D1803-M-E2B 0.21 rad. after T.D.C.
Close V2003-M-E2B
(Exhaust valve) V2203-M-E2B 12° after T.D.C.
V2403-M-E2B
0.24 rad. after T.D.C.
V2003-M-T-E2B
14° after T.D.C.
Rocker arm shaft to rocker arm
0.016 to 0.045 mm 0.1 mm
Clearance All models
0.00063 to 0.00177 in. 0.0039 in.

Rocker arm shaft 13.973 to 13.984 mm

All models
O.D. 0.55012 to 0.55055 in.

14.000 to 14.018 mm
Rocker arm I.D. All models 0.55118 to 0.55189 in.

Push rod

0.25 mm
Alignment All models
0.0098 in.

Tappet to tappet guide

0.020 to 0.062 mm 0.07 mm
Clearance All models
0.00079 to 0.00244 in. 0.0028 in.

23.959 to 23.980 mm
Tappet O.D. All models
0.94327 to 0.94410 in.

24.000 to 24.021 mm
Tappet guide I.D. All models
0.94488 to 0.94571 in.

KiSC issued 09, 2007 A

 (4/14)

Item Factory Specification Allowable Limit

Timing gear Backlash (Crank 0.0415 to 0.1122 mm 0.15 mm
All models
gear to idle gear) 0.00163 to 0.00442 in. 0.0059 in.
Backlash (Idle gear All models 0.0415 to 0.1154 mm 0.15 mm
to cam gear) 0.00163 to 0.00454 in. 0.0059 in.
Backlash (Idle gear 0.0415 to 0.1154 mm 0.15 mm
to injection pump gear) All models 0.00163 to 0.00454 in. 0.0059 in.
Backlash (Crank 0.0415 to 0.1090 mm 0.15 mm
gear to oil pump gear) All models 0.00163 to 0.00429 in. 0.0059 in.
Backlash (Idle gear Balancer 0.0350 to 0.1160 mm 0.15 mm
to balancer gear) model only 0.00138 to 0.00457 in. 0.0059 in.
Idle gear

0.12 to 0.48 mm 0.9 mm

Side clearance All models
0.0047 to 0.0189 in. 0.0354 in.

Idle gear shaft to idle gear bushing

0.025 to 0.066 mm 0.1 mm
Clearance All models
0.00098 to 0.00260 in. 0.0039 in.

Idle gear shaft 37.959 to 37.975 mm

All models
O.D. 1.49445 to 1.49508 in.

Idle gear bushing All models 38.000 to 38.025 mm

I.D. 1.49606 to 1.49704 in.

Camshaft

Alignment All models 0.01 mm

0.0004 in.

Camshaft

0.07 to 0.22 mm 0.3 mm

Side clearance All models
0.0028 to 0.0087 in. 0.0118 in.

Cam
Height 33.90 mm 33.85 mm
(Intake) All models
1.3346 in. 1.3327 in.

Height 33.90 mm 33.85 mm

(Exhaust) All models
1.3346 in. 1.3327 in.

KiSC issued 09, 2007 A

 (5/14)

Item Factory Specification Allowable Limit

Camshaft journal to cylinder block bore
0.050 to 0.091 mm 0.15 mm
Oil clearance All models
0.0020 to 0.0036 in. 0.0059 in.

Camshaft journal 39.934 to 39.950 mm

All models
O.D. 1.57221 to 1.57284 in.

Cylinder block 40.000 to 40.025 mm

All models
bore I.D. 1.57480 to 1.57579 in.

Balancer shaft

Balancer 0.07 to 0.22 mm 0.3 mm

Side clearance model only 0.0028 to 0.0087 in. 0.0118 in.

Balancer shaft journal 1 to

balancer shaft bearing 1 Oil clearance Balancer 0.030 to 0.111 mm 0.2 mm
model only 0.00118 to 0.00437 in. 0.0079 in.

Balancer shaft Balancer 43.934 to 43.950 mm

journal 1 O.D. model only 1.72968 to 1.73031 in.

Balancer shaft Balancer 43.980 to 44.045 mm

bearing 1 I.D. model only 1.73149 to 1.73405 in.

Balancer shaft journal 2 to

Balancer 0.030 to 0.111 mm 0.2 mm
balancer shaft bearing 2 Oil clearance
model only 0.00118 to 0.00437 in. 0.0079 in.

Balancer shaft Balancer 41.934 to 41.950 mm

journal 2 O.D. model only 1.65094 to 1.65157 in.

Balancer shaft Balancer 41.980 to 42.045 mm

bearing 2 I.D. model only 1.65275 to 1.65531 in.

Balancer shaft journal 3 to

Balancer 0.020 to 0.094 mm 0.2 mm
balancer shaft bearing 3 Oil clearance
model only 0.00079 to 0.00370 in. 0.0079 in.

Balancer shaft Balancer 21.947 to 21.960 mm

journal 3 O.D. model only 0.86405 to 0.86456 in.

Balancer shaft Balancer 21.980 to 22.041 mm

bearing 3 I.D. model only 0.86535 to 0.86775 in.

Piston pin bore

25.000 to 25.013 mm 25.05 mm

Piston pin bore I.D. All models
0.98425 to 0.98476 in. 0.9862 in.

KiSC issued 09, 2007 A

 (6/14)

Item Factory Specification Allowable Limit

Piston pin to small end bushing
0.014 to 0.038 mm 0.15 mm
Clearance All models
0.00055 to 0.00150 in. 0.0059 in.

25.002 to 25.011 mm
Piston pin O.D. All models
0.98433 to 0.98468 in.

Small end bushing 25.025 to 25.040 mm

All models
I.D. 0.98523 to 0.98582 in.

Piston ring
D1503-M-E2B
0.20 to 0.35 mm 1.25 mm
V2003-M-E2B
0.0079 to 0.0138 in. 0.0492 in.
V2003-M-T-E2B
Ring gap
(Top ring) D1703-M-E2B
D1803-M-E2B 0.25 to 0.40 mm 1.25 mm
V2203-M-E2B 0.0098 to 0.0157 in. 0.0492 in.
V2403-M-E2B
D1503-M-E2B
D1703-M-E2B
0.30 to 0.45 mm 1.25 mm
D1803-M-E2B
0.0118 to 0.0177 in. 0.0492 in.
Ring gap V2203-M-E2B
(Second ring) V2403-M-E2B

V2003-M-E2B 0.40 to 0.55 mm 1.25 mm

V2003-M-T-E2B 0.0157 to 0.0217 in. 0.0492 in.

Ring gap 0.25 to 0.45 mm 1.25 mm

All models
(Oil ring) 0.0098 to 0.0177 in. 0.0492 in.
Piston ring groove to piston ring
Clearance 0.093 to 0.128 mm 0.2 mm
All models
(Second ring) 0.00367 to 0.00504 in. 0.0079 in.

Clearance 0.020 to 0.060 mm 0.15 mm

All models
(Oil ring) 0.00079 to 0.00236 in. 0.0059 in.

Connecting rod

0.05 mm
Alignment All models
0.0020 in.

Crankshaft

0.02 mm
Alignment All models
0.0008 in.

KiSC issued 09, 2007 A

 (7/14)

Item Factory Specification Allowable Limit

Crankshaft journal to crankshaft
0.040 to 0.118 mm 0.2 mm
bearing 1 Oil clearance All models
0.00157 to 0.00465 in. 0.0079 in.

Crankshaft journal 59.921 to 59.940 mm

All models
O.D. 2.35909 to 2.35984 in.

Crankshaft bearing 1 59.980 to 60.039 mm

All models
I.D. 2.36142 to 2.36374 in.

Crankshaft journal to crankshaft

0.040 to 0.104 mm 0.2 mm
bearing 2 Oil clearance All models
0.00157 to 0.00409 in. 0.0079 in.

Crankshaft journal 59.921 to 59.940 mm

All models
O.D. 2.35909 to 2.35984 in.

Crankshaft bearing 2 59.980 to 60.025 mm

All models
I.D. 2.36142 to 2.36318 in.

Crankpin to crankpin bearing

0.025 to 0.087 mm 0.2 mm
Oil clearance All models
0.00098 to 0.00343 in. 0.0079 in.

46.959 to 46.975 mm
Crankpin O.D. All models
1.84878 to 1.84941 in.

Crankpin bearing 47.000 to 47.046 mm

All models
I.D. 1.85039 to 1.85220 in.

Crankshaft

0.15 to 0.31 mm 0.5 mm

Side clearance All models
0.0059 to 0.0122 in. 0.0197 in.

Crankshaft sleeve

0.1 mm
Wear All models
0.0039 in.

KiSC issued 09, 2007 A

 (8/14)

Item Factory Specification Allowable Limit

Cylinder D1503-M-E2B
83.000 to 83.022 mm 83.172 mm
V2003-M-E2B
3.26772 to 3.26858 in. 3.27448 in.
V2003-M-T-E2B
Bore I.D.
(Standard size) D1703-M-E2B
D1803-M-E2B 87.000 to 87.022 mm 87.172 mm
V2203-M-E2B 3.42519 to 3.42606 in. 3.43196 in.
V2403-M-E2B
D1503-M-E2B
83.250 to 83.272 mm 83.422 mm
V2003-M-E2B
3.27756 to 3.27843 in. 3.28432 in.
V2003-M-T-E2B
Bore I.D.
(Oversize) D1703-M-E2B
D1803-M-E2B 87.250 to 87.272 mm 87.422 mm
V2203-M-E2B 3.43503 to 3.43590 in. 3.44180 in.
V2403-M-E2B

KiSC issued 09, 2007 A

 (9/14)
(2) LUBRICATING SYSTEM
Item Factory Specification Allowable Limit
Engine oil pressure
49 kPa
Engine oil pressure
All models 0.5 kgf/cm2
(At idle speed)
7 psi

294.2 to 441.0 kPa 245 kPa

Engine oil pressure
All models 3.0 to 4.5 kgf/cm2 2.5 kgf/cm2
(At rated speed)
42.7 to 64.0 psi 36 psi

Inner rotor to outer rotor (Oil pump)

0.03 to 0.14 mm 0.2 mm

Clearance All models
0.0012 to 0.0055 in. 0.0079 in.

Outer rotor to pump body (Oil pump)

0.11 to 0.19 mm 0.25 mm

Clearance All models
0.0043 to 0.0075 in. 0.0098 in.

Inner rotor to cover (Oil pump)

0.105 to 0.150 mm 0.2 mm

Clearance All models
0.00413 to 0.00591 in. 0.0079 in.

KiSC issued 09, 2007 A

 (10/14)
(3) COOLING SYSTEM
Item Factory Specification Allowable Limit
Fan belt

7.0 to 9.0 mm
(0.28 to 0.35 in.)
Tension All models deflection at 98 N
(10 kgf, 22 lbs)
of force

Thermostat
Valve opening 69.5 to 72.5 °C
temperature All models
157.1 to 162.5 °F
(At beginning)

Valve opening 85 °C
temperature All models
185 °F
(Opened completely)

Radiator

No water leak at
Water tightness All models 137 kPa
1.4 kgf/cm2
20 psi

Radiator cap

10 seconds or more
for pressure falling
Pressure falling
All models from 88 to 59 kPa
time
(from 0.9 to 0.6 kgf/cm2,
from 13 to 9 psi)

KiSC issued 09, 2007 A

 (11/14)
(4) FUEL SYSTEM
Item Factory Specification Allowable Limit
Injection pump

0.297 to 0.331 rad. before

Injection timing All models T.D.C.
17 to 19° before T.D.C.

Injection nozzle

13.7 to 14.7 MPa

Injection pressure All models 140 to 150 kgf/cm2
1991 to 2133 psi

Injection nozzle

No fuel leak at
Valve seat tightness All models 12.75 MPa
130 kgf/cm2
1849 psi

KiSC issued 09, 2007 A

 (12/14)
(5) ELECTRICAL SYSTEM
Item Factory Specification Allowable Limit
Starter
D1503-M-E2B
D1703-M-E2B 30.0 mm 29.0 mm
V2003-M-E2B
1.181 in 1.142 in.
V2003-M-T-E2B
Commutator O.D. V2203-M-E2B

D1803-M-E2B 35.0 mm 34.0 mm

V2403-M-E2B 1.378 in. 1.339 in.

Starter

0.45 to 0.75 mm 0.20 mm

Mica under cut All models
0.0177 to 0.0295 in. 0.0079 in.

Starter
D1503-M-E2B
D1703-M-E2B 15.0 mm 11.0 mm
V2003-M-E2B
0.591 in. 0.433 in.
V2003-M-T-E2B
Brush length V2203-M-E2B

D1803-M-E2B 15.0 mm 9.0 mm

V2403-M-E2B 0.591 in. 0.354 in.

Starter

Brush holder
resistance
All models Infinity
(Brush holder -
Holder support)

Starter

Field coil resistance

(Lead - Brush) All models Continuity

Starter

Field coil resistance

(Brush - Yoke) All models Infinity

KiSC issued 09, 2007 A

 (13/14)

Item Factory Specification Allowable Limit

Starter

Armature coil
resistance All models Infinity
(Commutator -
Armature coil core)

Starter

Armature coil
resistance All models Continuity
(Segment -
Segment)

Alternator

Stator resistance All models Less than 1.0

Alternator

Rotor resistance All models 2.9

Alternator

14.4 mm 14.0 mm
Slip ring O.D. All models
0.567 in. 0.551 in.

Alternator

10.5 mm 8.4 mm
Brush length All models
0.413 in. 0.331 in.

KiSC issued 09, 2007 A

 (14/14)

Item Factory Specification Allowable Limit

Glow plug

Resistance All models Approx. 0.9

Stop solenoid
Resistance
All models Approx. 0.38
(Terminal 1 - body)
1 2

Resistance
All models Approx. 15.58
(Terminal 2 - body)

KiSC issued 09, 2007 A

 (1/3)
TIGHTENING TORQUES
(1) Special Tightening Torques
For " * " marked screws, bolts and nuts on under table, apply engine oil to their threads and seats before tightening.
Cylinder head cover screw Main bearing case screw 1 * Main bearing case screw 2 *

D1503-M-E2B D1503-M-E2B D1503-M-E2B

D1703-M-E2B D1703-M-E2B D1703-M-E2B
D1803-M-E2B 6.9 to 11.3 N m D1803-M-E2B 46.1 to 50.9 N m D1803-M-E2B 68.6 to 73.5 N m
V2003-M-E2B 0.70 to 1.15 kgf m V2003-M-E2B 4.7 to 5.2 kgf m V2003-M-E2B 7.0 to 7.5 kgf m
V2003-M-T-E2B 5.1 to 8.3 ft-lbs V2003-M-T-E2B 34.0 to 37.6 ft-lbs V2003-M-T-E2B 50.6 to 54.2 ft-lbs
V2203-M-E2B V2203-M-E2B V2203-M-E2B
V2403-M-E2B V2403-M-E2B V2403-M-E2B

Cylinder head screw * Cylinder head tightening order

(A) 3 cylinder model (B) 4 cylinder model

j b g n f c k
n f c k r j b g o

m e d l q i a h p
i a h m e d l

D1503-M-E2B D1503-M-E2B
D1703-M-E2B D1703-M-E2B
D1803-M-E2B 93.1 to 98.0 N m D1803-M-E2B (A) 3 cylinder model
V2003-M-E2B 9.5 to 10.0 kgf m V2003-M-E2B a n
V2003-M-T-E2B V2003-M-T-E2B (B) 4 cylinder model
68.7 to 72.3 ft-lbs
V2203-M-E2B V2203-M-E2B a r
V2403-M-E2B V2403-M-E2B

Flywheel screw * Connecting rod screw * Rocker arm bracket screw *

D1503-M-E2B D1503-M-E2B D1503-M-E2B

D1703-M-E2B D1703-M-E2B D1703-M-E2B
D1803-M-E2B 98.0 to 107.8 N m D1803-M-E2B 44.1 to 49.0 N m D1803-M-E2B 23.5 to 27.5 N m
V2003-M-E2B 10.0 to 11.0 kgf m V2003-M-E2B 4.5 to 5.0 kgf m V2003-M-E2B 2.4 to 2.8 kgf m
V2003-M-T-E2B 72.3 to 79.5 ft-lbs V2003-M-T-E2B 32.5 to 36.2 ft-lbs V2003-M-T-E2B 17.4 to 20.3 ft-lbs
V2203-M-E2B V2203-M-E2B V2203-M-E2B
V2403-M-E2B V2403-M-E2B V2403-M-E2B

KiSC issued 09, 2007 A

 (2/3)

Idle gear shaft screw * Bearing case cover screw * Fan drive pulley mounting nut

D1503-M-E2B D1503-M-E2B D1503-M-E2B

D1703-M-E2B D1703-M-E2B D1703-M-E2B
D1803-M-E2B 23.5 to 27.5 N m D1803-M-E2B 23.5 to 27.5 N m D1803-M-E2B 137.3 to 156.9 N m
V2003-M-E2B 2.4 to 2.8 kgf m V2003-M-E2B 2.4 to 2.8 kgf m V2003-M-E2B 14.0 to 16.0 kgf m
V2003-M-T-E2B 17.4 to 20.3 ft-lbs V2003-M-T-E2B 17.4 to 20.3 ft-lbs V2003-M-T-E2B 101.3 to 115.7 ft-lbs
V2203-M-E2B V2203-M-E2B V2203-M-E2B
V2403-M-E2B V2403-M-E2B V2403-M-E2B

Glow plug Nozzle holder assembly Oil switch taper screw

D1503-M-E2B D1503-M-E2B D1503-M-E2B

D1703-M-E2B D1703-M-E2B D1703-M-E2B
D1803-M-E2B 19.6 to 24.5 N m D1803-M-E2B 49.0 to 68.6 N m D1803-M-E2B 14.7 to 19.6 N m
V2003-M-E2B 2.0 to 2.5 kgf m V2003-M-E2B 5.0 to 7.0 kgf m V2003-M-E2B 1.5 to 2.0 kgf m
V2003-M-T-E2B 14.5 to 18.1 ft-lbs V2003-M-T-E2B 36.2 to 50.6 ft-lbs V2003-M-T-E2B 10.8 to 14.5 ft-lbs
V2203-M-E2B V2203-M-E2B V2203-M-E2B
V2403-M-E2B V2403-M-E2B V2403-M-E2B

Injection pipe retaining nut Overflow pipe assembly Camshaft set screw
retaining nut

D1503-M-E2B D1503-M-E2B D1503-M-E2B

D1703-M-E2B D1703-M-E2B D1703-M-E2B
D1803-M-E2B 24.5 to 34.3 N m D1803-M-E2B 19.6 to 24.5 N m D1803-M-E2B 23.5 to 27.5 N m
V2003-M-E2B 2.5 to 3.5 kgf m V2003-M-E2B 2.0 to 2.5 kgf m V2003-M-E2B 2.4 to 2.8 kgf m
V2003-M-T-E2B 18.1 to 25.3 ft-lbs V2003-M-T-E2B 14.5 to 18.1 ft-lbs V2003-M-T-E2B 17.4 to 20.3 ft-lbs
V2203-M-E2B V2203-M-E2B V2203-M-E2B
V2403-M-E2B V2403-M-E2B V2403-M-E2B

KiSC issued 09, 2007 A

 (3/3)

Hi-idling body Balancer shaft set bolt Alternator pulley nut

D1503-M-E2B D1503-M-E2B D1503-M-E2B

D1703-M-E2B D1703-M-E2B D1703-M-E2B
D1803-M-E2B 44.1 to 49.0 N m D1803-M-E2B 23.5 to 27.5 N m D1803-M-E2B 58.3 to 78.9 N m
V2003-M-E2B 4.5 to 5.0 kgf m V2003-M-E2B 2.4 to 2.8 kgf m V2003-M-E2B 5.95 to 8.05 kgf m
V2003-M-T-E2B 32.6 to 36.3 ft-lbs V2003-M-T-E2B 17.4 to 20.3 ft-lbs V2003-M-T-E2B 43.0 to 58.2 ft-lbs
V2203-M-E2B V2203-M-E2B V2203-M-E2B
V2403-M-E2B V2403-M-E2B V2403-M-E2B

(2) General Tightening Torques

Screw and bolt material grades are shown by numbers punched on the screw and bolt heads.
Prior to tightening, be sure to check out the numbers as shown below.
None or 4 : Standard grade
7 : Special grade

Nominal Diameter Standard Grade Special Grade

7.9 to 9.3 N m 9.8 to 11.3 N m
M6 0.80 to 0.95 kgf m 1.00 to 1.15 kgf m
5.8 to 6.9 ft-lbs 7.23 to 8.32 ft-lbs

17.7 to 20.6 N m 23.5 to 27.5 N m

M8 1.8 to 2.1 kgf m 2.4 to 2.8 kgf m
13.0 to 15.2 ft-lbs 17.4 to 20.3 ft-lbs

39.2 to 45.1 N m 48.1 to 55.9 N m

M10 4.0 to 4.6 kgf m 4.9 to 5.7 kgf m
28.9 to 33.3 ft-lbs 35.4 to 41.2 ft-lbs

62.8 to 72.6 N m 77.5 to 90.2 N m

M12 6.4 to 7.4 kgf m 7.9 to 9.2 kgf m
46.3 to 53.5 ft-lbs 57.1 to 66.5 ft-lbs

KiSC issued 09, 2007 A