DROID TURBO 2 /

Moto X Force

DROID TURBO 2 / Moto X Force

Level 2 – Service and Repair Manual
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

REVISION HISTORY
Revision Date Notes
1 10/30/2015 Initial release.
Bounce Chassis Screw Guide (3-00-F6-10000) added to Tools Required for
2 12/04/2015
Assembly and Battery Assembly.
• Figure 8 updated to include the DROID Logo.
• Table 3 updated to include rework Audio Bezels and the DROID Logos.
• Audio Bezel and DROID Logo added to Disassembly and Recovery Map.
• Bounce Inlay Heating Plate (3-00-F5-10000) and “7x7” Hot Plate
(4-00-Z2-10000 (220V) /4-00-Z3-10000 (110V)) added to the Tools Required
for Disassembly.
• The Rear Inlay Removal section was updated to include pre-heating
instructions using the Bounce Inlay Heating Plate (3-00-F5-10000).
• The following sections were added to Disassembly and Recovery:
o Audio Deco Removal
3 01/28/2016 o DROID Logo Removal
o Side Key Removal
• DROID Logo added to Assembly Map.
• The Tools Required for Assembly section was updated to include the new
Bounce Audio Bezel Press Tool (3-00-F7-10000) and an updated image of the
Bounce Earpiece Deco Press Fixture (3-00-D8-10000).
• The Rear Inlay Assembly section was updated to include assembly of the
DROID Logo.
• The Audio Deco Assembly section was updated to include rework Audio
Bezels, updated images of the Bounce Earpiece Deco Press Fixture (3-00-D8-
10000), and the new Bounce Audio Bezel Press Tool (3-00-F7-10000).

Motorola Mobility Confidential Restricted:

PAGE 2 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

TABLE OF CONTENTS
Revision History .................................................................................................................................................. 2 _Toc441747693

List of Tables ................................................................................................................................................................. 6

Table of Figures ............................................................................................................................................................ 6
Safety Information ........................................................................................................................................................ 7
Cautions and Warnings ....................................................................................................................................... 7 _Toc441747698

Battery Safety Guidelines .............................................................................................................................................. 7

Introduction................................................................................................................................................................... 8
External Views .............................................................................................................................................................. 8
PSCD Gaps.................................................................................................................................................................. 10
Exploded Views ........................................................................................................................................................... 18
DLN Liner Replacement .............................................................................................................................................. 23
Tools Required for DLN Liner Replacement ................................................................................................................. 23
MASC Procedure ......................................................................................................................................................... 24
Customer Procedure ................................................................................................................................................... 29
Disassembly and Recovery ........................................................................................................................................ 31
Disassembly and Recovery Map .................................................................................................................................. 31
Tools Required for Disassembly .................................................................................................................................. 32
SIM/SD Tray Removal ................................................................................................................................................. 33
Water Detection Label Inspection ................................................................................................................................ 34
Audio Deco Removal ................................................................................................................................................... 35
Rear Inlay Removal ..................................................................................................................................................... 36
Rear-Facing Imager Bezel Removal ............................................................................................................................. 39
Rear-Facing Imager Lens Removal .............................................................................................................................. 40
DROID Logo Removal .................................................................................................................................................. 41
Rear Housing Removal ................................................................................................................................................ 42
Side Key Removal ....................................................................................................................................................... 44
Battery Disconnection ................................................................................................................................................. 45
Front-Facing Imager Removal ..................................................................................................................................... 47
Front-Facing Imager Gasket Removal .......................................................................................................................... 48
Earpiece Speaker Removal .......................................................................................................................................... 49
Secondary-Microphone Grommet Removal.................................................................................................................. 50
Battery Removal .......................................................................................................................................................... 51
PCB Removal .............................................................................................................................................................. 52
Trim Ring Removal ...................................................................................................................................................... 54
IR LED Flex Removal ................................................................................................................................................... 55
IR LED Grommet Removal ........................................................................................................................................... 56
Coax Cable Removal ................................................................................................................................................... 57

Motorola Mobility Confidential Restricted:

PAGE 3 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear-Facing Imager Removal ...................................................................................................................................... 58

Proximity Grommet Removal ....................................................................................................................................... 59
Microphone Grommet Removal ................................................................................................................................... 60
Loudspeaker Removal ................................................................................................................................................. 61
Vibrator Removal ......................................................................................................................................................... 62
Headset Jack Removal ................................................................................................................................................ 63
NFC Antenna Removal................................................................................................................................................. 64
Parts Refresh .............................................................................................................................................................. 65
Tools Required for Parts Refresh ................................................................................................................................. 65
Battery Cleaning.......................................................................................................................................................... 66
PCB Cleaning .............................................................................................................................................................. 68
Rear Housing Cleaning ................................................................................................................................................ 70
Rear Inlay Cleaning ..................................................................................................................................................... 72
Assembly ..................................................................................................................................................................... 73
Assembly Map ............................................................................................................................................................ 73
Tools Required for Assembly ....................................................................................................................................... 74
Rear Housing WDL Assembly ...................................................................................................................................... 77
PCB Preparation .......................................................................................................................................................... 78
ZIF Connector Pad Assembly ....................................................................................................................................... 83
Proximity Grommet Assembly ..................................................................................................................................... 85
IR LED Grommet Assembly .......................................................................................................................................... 86
Main-Microphone Grommet Assembly......................................................................................................................... 87
IR LED Flex Assembly .................................................................................................................................................. 89
Rear-Facing Imager Assembly..................................................................................................................................... 90
Trim Ring Assembly .................................................................................................................................................... 91
Coax Cable Assembly .................................................................................................................................................. 95
PCB Assembly ............................................................................................................................................................. 97
Earpiece Speaker Assembly ...................................................................................................................................... 102
Front-Facing Imager Assembly .................................................................................................................................. 103
Secondary-Microphone Grommet Assembly .............................................................................................................. 105
Battery Adhesive Assembly ....................................................................................................................................... 106
Battery Assembly ...................................................................................................................................................... 107
Heatspreader Assembly ............................................................................................................................................ 110
NFC Antenna Assembly ............................................................................................................................................. 112
Vibrator Assembly ..................................................................................................................................................... 114
Headset Jack Assembly ............................................................................................................................................ 116
Loudspeaker Assembly ............................................................................................................................................. 118
Rear Housing Assembly............................................................................................................................................. 120
Rear-Facing Imager Lens Assembly .......................................................................................................................... 124

Motorola Mobility Confidential Restricted:

PAGE 4 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear Inlay Assembly .................................................................................................................................................. 125

Audio Deco Assembly................................................................................................................................................ 132
SIM/SD Tray Assembly .............................................................................................................................................. 135

Motorola Mobility Confidential Restricted:

PAGE 5 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

LIST OF TABLES
Table 1. External Views Parts List ................................................................................................................................... 9
Table 2. PSCD Gap Measurements ................................................................................................................................ 16
Table 3. Exploded View Parts List.................................................................................................................................. 18
Table 4. Subassembly Exploded View Parts List ............................................................................................................ 21

TABLE OF FIGURES
Figure 1. External Views.................................................................................................................................................. 8
Figure 2. PSCD Front View ............................................................................................................................................ 10
Figure 3. PSCD Rear View ............................................................................................................................................. 11
Figure 4. PSCD Side View ............................................................................................................................................. 12
Figure 5. PSCD Top View and Cross Section View ......................................................................................................... 13
Figure 6. PSCD Display Alignment ................................................................................................................................. 14
Figure 7. PSCD Front-Facing Imager Alignment............................................................................................................. 15
Figure 8. Assembly Exploded View ................................................................................................................................ 18
Figure 9. Subassembly Exploded View .......................................................................................................................... 21

Motorola Mobility Confidential Restricted:

PAGE 6 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

SAFETY INFORMATION
Cautions and Warnings
Electrostatic Discharge
The phone components may be damaged by electrostatic discharge (ESD). Always use an ESD mat and ground strap
when working with internal components.

Battery Safety Guidelines

Handle Battery with care. Ensure Battery edges and surfaces are not dented or deformed. If the Battery Pack is dropped
to the floor, it may be internally damaged and must be scrapped.
Ensure all surfaces, fixtures, and phone components contacting the Battery are smooth and clean.
• Ensure Battery and its insulation are not damaged (e.g. scratched, dented, punctured) prior to and throughout
assembly.
• Prior to assembly, ensure Battery edges and surfaces are not dented or deformed, and that fixtures and parts that
will contact the Battery are free of foreign material.
• Ensure screws and screwdrivers do not contact the Battery.
• Failure to adhere to Safety Critical Note(s) may increase risk of rupture, burning, or failure to function safely when
used by the customer.

Motorola Mobility Confidential Restricted:

PAGE 7 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

INTRODUCTION
External Views

Figure 1. External Views

Motorola Mobility Confidential Restricted:

PAGE 8 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Table 1. External Views Parts List

Reference # Description
1 Front-Facing LED Flash
2 Earpiece Speaker
3 Front-Facing Imager
4 Display Lens
5a Power Key
5b Volume Key
6 Rear-Facing Imager Bezel
7 Rear-Facing Imager
8 LED Flash
9 Motorola Logo
10 Rear Housing
11 USB Port
12 Headset Jack
13 SIM and SD Card Tray
14 Main Microphone
15a Loudspeaker
15b Loudspeaker

Motorola Mobility Confidential Restricted:

PAGE 9 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

PSCD Gaps
All dimensions are in millimeters (mm). The following gaps are considered maximum allowable without further approval
from a supervisor. Measure gaps at an angle perpendicular to the surface/area being measured. Feeler Gauges must
not be used at an angle as they will give false-positive results.

Figure 2. PSCD Front View

Motorola Mobility Confidential Restricted:

PAGE 10 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Figure 3. PSCD Rear View

Motorola Mobility Confidential Restricted:

PAGE 11 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Figure 4. PSCD Side View

Motorola Mobility Confidential Restricted:

PAGE 12 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Figure 5. PSCD Top View and Cross Section View

Motorola Mobility Confidential Restricted:

PAGE 13 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Figure 6. PSCD Display Alignment

Motorola Mobility Confidential Restricted:

PAGE 14 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Figure 7. PSCD Front-Facing Imager Alignment

Motorola Mobility Confidential Restricted:

PAGE 15 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Table 2. PSCD Gap Measurements

Reference # Description
1 Front Rim Housing to Lens Liner Perimeter
2 Lens Liner to Audio Deco (Left Point) Step
3 Lens Liner to Audio Deco (Right Point) Step
4 Audio Deco Tilt (Left Point vs. Right Point) Step
5 Rear Band Housing to Rear Inlay Perimeter
6 Main Imager Center to Main Imager Lens Artwork Concentricity
7 Camera Deco M Logo Rotation
8 Power Key to Rear Band Housing Step
9 Volume Key to Rear Band Housing Step
10 Main Imager Center to Camera Deco Concentricity
11 Camera Deco to Flash Lens Perimeter
12 Rear Inlay to Rear Bezel Perimeter
13 Rear Bezel to Camera Deco Perimeter
14 Rear Inlay to Droid Logo Perimeter
15 Front Rim Housing to Rear Band Housing (Z)
16 Front Rim Housing to Rear Band Housing Step (X & Y)
17 Rear Band Housing to Power Key (Y)
18 Rear Band Housing to Power Key (Z)
19 Rear Band Housing to Volume Key (Z)
20 Rear Band Housing to Volume Key (Y)
21 Rear Band Housing to SIM Door Perimeter
22 Front Rim Housing to Rear Band Housing Step (X & Y)
23 Rear Band Housing to SIM Door Step
24 Rear Band Housing to Rear Inlay Step
25 Rear Inlay to Rear Bezel Step
26 Rear Bezel to Camera Deco Step
27 Camera Deco to Camera Lens Step
28 Front Rim Housing to Main Lens Step
29 Camera Deco to Camera Flash Lens Step
30 Rear Inlay to Droid Logo Step
31 Main Lens View Area to Display Active Area (X1-X2)
32 Main Lens View Area to Display Active Area (Y1-Y2)

Motorola Mobility Confidential Restricted:

PAGE 16 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Reference # Description
33 Front-Facing Imager Center to Main Lens Artwork Center Concentricity

Motorola Mobility Confidential Restricted:

PAGE 17 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Exploded Views

Figure 8. Assembly Exploded View

Table 3. Exploded View Parts List

Reference # Description Recovery Part

1 DIE CUT,LINER,LENS,NO BRANDING NO
ASSY,HSG,AU DECO,T&R,METALLIC RED,KINZIE (REWORK) NO
BZL,AU DECO,METALLIC BLK (REWORK)
BZL,AU DECO,METALLIC SLVR (REWORK)
BZL,AU DECO,METALLIC DK GRY (REWORK)
2
ASSY,HSG,AU DECO,T&R,METALLIC RED,KINZIE (ORIGINAL)
BZL,AU DECO,METALLIC BLK (ORIGINAL)
BZL,AU DECO,METALLIC SLVR (ORIGINAL)
BZL,AU DECO,METALLIC DK GRY (ORIGINAL)
ASSY,HSG,LENS W/FRONT HOUSING,PSA,BLACK,ROW,KINZIE YES
3
ASSY,HSG,LENS W/FRONT HOUSING,PSA,WHITE,ROW,KINZIE
HSG,FRNT RIM,DECORATED,BLACK NO
4
HSG,FRNT RIM,DECORATED,WHITE
5 GROM,SENSOR,KINZIE NO

6 TRANSDUCER,OTHR,6X12X3,6X12X3MM RCVR F0=200HZ, AAC NO

7 SEAL,O-RING,FRONT IMGR NO

8 ASSY,FLXCKT,5MP IMAGER,KINZIE YES

9 CABLE,COAX YES

Motorola Mobility Confidential Restricted:

PAGE 18 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Reference # Description Recovery Part

ASSY,HSG,SIM DOOR, FULL FLOOR TRAY,DARK MTLC GRAY, KINZIE YES
ASSY,HSG,SIM DOOR,FULL FLOOR TRAY,LIGHT
ASSY,HSG,SIM DOOR, FULL FLOOR TRAY,SINGLE SIM,METALLIC DK
GRAY
10 ASSY,HSG,SIM DOOR, FULL FLOOR TRAY,SINGLE SIM,METALLIC
SILVER,KI
ASSY,HSG,SIM DOOR, FULL FLOOR TRAY,SINGLE SIM,METALLIC
CHAMPAGNE
ASSY,HSG,SIM DOOR, FULL FLOOR TRAY,SINGLE SIM,RED,KINZIE
ASSY,PWA,MN,BOUNCE VZW YES
ASSY,PWA,MN,BOUNCE,ROW
11 ASSY,PWA,MN,64 GB,BOUNCE,VZW
ASSY,PWA,MN,64 GB,BOUNCE,ROW
ASSY,PWA,MN,32 GB,BOUNCE,CHINA,ROW
12 ASSY,PWA,TOP,HSJ,VIBRATOR,KINZIE YES
13 DIE CUT,ADHESIVE,PCB-CHASSIS NO
14 ASSY,FLXCKT,IR LED,KINZIE YES
15 PAD,CONDUCTIVE,FRONT IMGR NO
16 ASSY,FLXCKT,CAMERA,REAR FACING 21MP IMAGER,KINZIE YES
17 DIE CUT,ADHES,COP TAPE,PM8994 NO
18 ASSY,CHAS,REAR,KINZIE YES
19 TRANSDUCER,POLYPHONIC,13X18X2P5 NO
20 ASSY,BAT,LI POLY,FB55,3760MAH,LG CHEM YES
21 PAD,CONDUCTIVE,FRONT IMGR NO
ASSY,HSG,REAR,METALLIC DK GRY YES
ASSY,HSG,REAR,TIN SILVER,KINZIE
22
ASSY,HSG,REAR,CHAMPAGNE,KINZIE
ASSY,HSG,REAR,RED,KINZIE
23 ASSY,HSG,STOPPER,EARPIECE/FLASH,KINZIE YES
24 SCR,MACH,M1.4 NO
25 ASSY,HSG,STOPPER,NFC CONN YES
26 DIE CUT,ADHESIVE,INLAY,REAR COVER NO
ASSY,HSG,INLAY,CSR,BLACK,REAR COVER,ROW YES
ASSY,HSG,INLAY,CSR,WINTER WHITE,REAR COV
27 ASSY,HSG,INLAY,NYLON,BLACK,REAR CVR
ASSY,HSG,INLAY,NYLON,BLACK,ROW,REAR CVR
ASSY,HSG,INLAY,NYLON,GRAY,ROW,REAR CVR
BZL,DECO,REAR,METALLIC DK GRY YES
28 BZL,DECO,REAR,METALLIC SLVR
BZL,DECO,REAR,METALLIC RED

Motorola Mobility Confidential Restricted:

PAGE 19 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Reference # Description Recovery Part

29 DIE CUT,ADHES,CAMERA,DECO NO
ASSY,CAMR DECO,METALLIC SLVR YES
ASSY,CAMR DECO,METALLIC DK GRY
30
ASSY,CAMR DECO,METALLIC CHMPGN
ASSY,CAMR DECO,BLACK
ASSY,DROID LOGO,DARK MTLC GRAY,KINZIE NO
ASSY,DROID LOGO,DARK MTLC SILVER,KINZIE
31
ASSY,DROID LOGO,METALLIC CHAMPAGNE,TALL,KINZIE
ASSY,DROID LOGO,DARK GRAY/BLACK,KINZIE

Motorola Mobility Confidential Restricted:

PAGE 20 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Figure 9. Subassembly Exploded View

Table 4. Subassembly Exploded View Parts List

Reference # Description Recovery Part

2.1 SCRN,MESH,EARPIECE,TOP NO
2.2 SCRN,MESH,MIC5 NO
SCRN,MESH,METAL,BOTTOM,BLACK,KINZIE NO
2.3
SCRN,MESH,METAL,BOTTOM,SILVER,KINZIE
2.4 PAD,HT SPREADER,DISPLAY TO CHAS NO
ASSY,HSG,FRNT FLSH LENS,KINZIE NO
2.5
ASSY,HSG,FRNT FLSH LENS,WHITE,KINZIE
2.6 GROM,SEAL,MIC 5 NO
2.7 PAD,CONNECTOR,REAR IMGR NO
2.8 PAD,CUSHION,COAX CBL N
2.9 DIE CUT,KAPTON TAPE,FRONT CHASSIS,3.2MM X 22.5MM NO
2.10 DIE CUT,ADHES,CONDUCTIVE,DISPLAY FLX NO
2.11 SCRN,MESH,MIC 1&4 NO
5.1 FLX,NFC,WLC NO
5.2 SPCR,WLC COIL NO
5.3 ASSY,HSG,REAR,ENDO,KINZIE YES
5.4 ASSY,FLXCKT,AU NO
5.5 SCRN,MESH,MIC 2,CORE NO
5.6 SEAL,HSET JCK NO
5.7 CONN,JACK,HEADSET,3.5 MM DIA YES

Motorola Mobility Confidential Restricted:

PAGE 21 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Reference # Description Recovery Part

ALERT DEVICE,VIBR,MOTOR, ROTARY, 11.75 MM X X 4.55 MM MOTOR YES
5.8
BODY
5.9 USB PAD NO
5.10 DIE CUT,ADHES,LOUD NO
5.11 PLT,METAL,ANTENNA,FEED,X+1 NO
5.12 SCRN,MESH,MIC3 NO
5.13 SCRN,MESH,MYLAR,MIC2,CAV NO
5.14 LENS,IMAGER,REAR NO
5.15 ASSY,FLXCKT,FLASH,BOUNCE NO
5.16 PAD,CONNECTOR, FRNT IMGR NO
5.17 BTN,POWER,GRAPHITE GRAY,KINZIE YES
5.18 BTN,VOLUME,GRAPHITE GRAY,KINZIE YES
5.19 SEAL,32014943 MYLAR, BV-REV_A NO

Motorola Mobility Confidential Restricted:

PAGE 22 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

DLN LINER REPLACEMENT

Tools Required for DLN Liner Replacement
The following tools are required to replace the DLN Liner on the DROID TURBO 2 / Moto X Force phone.

Description Part # Picture / Drawing

Bounce Lens Liner Alignment Fixture

3-00-E3-10000

Lens Liner Roller

Lens Removal Pick Tool 3-00-E4-10000

Kimwipes 01018766001W --

Alpha Dry Wipes 01018765001W --

Compressed Air Spray Can -- --

Gloves or Finger Collets -- --

Motorola Mobility Confidential Restricted:

PAGE 23 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

MASC Procedure

Description Reference #
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,BLACK,KINZIE 1
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,WHITE,KINZIE
DIE CUT,LINER,LENS,NO BRANDING 2

1. Place the phone in the Bounce Lens Liner

Alignment Fixture (3-00-E3-10000).

Motorola Mobility Confidential Restricted:

PAGE 24 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

2. Place the alignment lid on the fixture.

3. Spray the Display and all 3 audio ports with
compressed air to remove any dust or foreign
material.

4. Use the Lens Removal Pick Tool (3-00-E4-

10000) to lift the corner of the old DLN Liner, and
then peel it off the Display.

Motorola Mobility Confidential Restricted:

PAGE 25 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

5. Wipe the Display with a Kimwipe in a clockwise

motion and remove any lint or dust.

6. Wipe the Display with an Alpha Dry Wipe in a

counterclockwise motion.

7. Spray the Display with compressed air to remove

any dust or foreign material.

8. Verify the Display is free of lint, dust, or any other

foreign material.

Motorola Mobility Confidential Restricted:

PAGE 26 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

9. Remove the adhesive liner from the DLN Liner.

10. Place the DLN Liner into the fixture over the
Display, using the pins in the fixture and the 3
audio ports and the 3 pins to align it.

11. Use the Lens Liner Roller or Lens Removal Pick

Tool to apply manual pressure to the DLN Liner
as follows: 5 2 5
• Place the roller or pick on point 1 and slide
out to point 2.
• Place the roller or pick on point 1 and slide
out to point 3.
• Place the roller or pick on point 1 and slide
out to point 4.
• Place the roller or pick on point 1 and slide
out to point 5. 3 3
1

4 2 4

Motorola Mobility Confidential Restricted:

PAGE 27 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

12. Remove the top liner from the DLN Liner.

13. Remove the phone from the fixture.
14. Use the roller or pick to press out any remaining
air bubbles.

NOTE
Small air bubbles will disappear over the next 48
hours.

Motorola Mobility Confidential Restricted:

PAGE 28 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Customer Procedure
1. Power off the phone.

2. Use the Lens Removal Pick Tool to lift the

corner. Then, peel off the lens.

3. Use the wet cloth, then dry cloth. Make sure

there’s no lint or dust left.

4. Pull tab 1 to remove the back cling.

5. Carefully align the new lens using the audio ports

as guides.

Motorola Mobility Confidential Restricted:

PAGE 29 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

6. Press and drag down, then across the center.

Wait 15 seconds, then press outward from the
center.

7. Pull tab 2 to remove the top cling. Wait 24 hours

and press out any remaining air bubbles.

NOTE
Use the tool to gently press down any air pockets.
Small air bubbles may disappear over the next 48
hours.

Motorola Mobility Confidential Restricted:

PAGE 30 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

DISASSEMBLY AND RECOVERY

Disassembly and Recovery Map

Audio Bezel

SIM/SD Tray

Rear Inlay

Rear-Facing Rear-Facing
DROID Logo
Imager Lens Imager Bezel

Secondary-
Earpiece Front-Facing Rear
NFC Antenna Microphone Vibrator Loudspeaker Headset Jack
Speaker Imager Housing
Grommet

Front-Facing
Imager Battery
Gasket

Main-
Rear-Facing IR LED Proximity
Coax Cable IR LED Flex Microphone PCB
Imager Grommet Grommet
Grommets

*Shaded parts may be eligible for parts recovery.

Motorola Mobility Confidential Restricted:

PAGE 31 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Tools Required for Disassembly

The following tools are required to disassemble the DROID TURBO 2 / Moto X Force phone.

Description Part # Picture / Drawing

Bounce Inlay Heating Plate 3-00-F5-10000

4-00-Z2-10000
(220V) /
“7x7” Hot Plate*
4-00-Z3-10000
(110V)

SIM Tray Removal Tool 4-00-U2-10000

Blackstick --

3IP Torx Bit --

Thin Plastic Spudger 0-00-00-40826

Tweezers (Plastic or Plastic-Tipped) -- --

Tweezers (Metal) -- --
ESD Mat and Wrist Strap -- --
Gloves or Finger Collets -- --
Isopropyl (ISP) Alcohol -- --
*Hot Plates 4-00-Z2-10000 and 4-00-Z3-10000 are identical tools. The only difference is the voltage rating. Either the
220V 4-00-Z2-10000 or the 110V 4-00-Z3-10000 can be used with the Bounce Inlay Heating Plate (3-00-F5-10000).

Motorola Mobility Confidential Restricted:

PAGE 32 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

SIM/SD Tray Removal

NOTE
The SIM/SD Tray can be recovered
and reused after removal.

1. Insert the SIM Tray Removal Tool into the

SIM/SD Tray hole.

2. Push the SIM Tray Removal Tool into the

SIM/SD Tray hole until the SIM/SD Tray ejects
from the phone.

3. Remove the SIM/SD Tray from the phone.

Motorola Mobility Confidential Restricted:

PAGE 33 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Water Detection Label Inspection

Inspect the Water Detection Label (WDL) visible
through the SIM/SD Tray slot.

Motorola Mobility Confidential Restricted:

PAGE 34 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Audio Deco Removal

Use the Thin Plastic Spudger to pry the Audio Bezel
from the Display.

NOTE
After you remove the Audio Bezel, you
cannot reuse it.

Motorola Mobility Confidential Restricted:

PAGE 35 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear Inlay Removal

NOTE
The Rear Inlay can be recovered and
reused after removal.

1. Place the Bounce Inlay Heating Plate

(3-00-F5-10000) on the Hot Plate.
2. Set the Hot Plate to 80 °C (176 °F).

// CAUTION //
Do not set the Hot Plate temperature higher than
80 °C (176 °F). Damage to the phone may occur.

3. Wait 10-15 minutes for the Hot Plate to warm up.

4. Place the phone in the plate, with the Display
side face up.
5. Wait 5-10 minutes for the Rear Inlay to warm up.
6. Remove the phone from the plate.

// CAUTION //
Wear protective gloves when handling heated
phones.

7. Insert the Thin Plastic Spudger at a 90° angle

between the Rear Inlay and Rear-Facing Imager
Bezel.

Motorola Mobility Confidential Restricted:

PAGE 36 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

8. Slide the Thin Plastic Spudger under the Rear

Inlay at an angle towards the corner nearest the
SIM/SD Tray slot. Slide the Spudger towards the
corner until the corner of the Rear Inlay lifts from
the Rear Housing.

9. After the corner of the Rear Inlay is lifted from

the Rear Housing, insert the flat end of the
Blackstick between the Rear Inlay and Rear
Housing.

10. Slide the Blackstick around the perimeter of the

Rear Inlay to separate the adhesive from the
Rear Housing.

// CAUTION //
Do not insert the Blackstick in the indicated area.

Motorola Mobility Confidential Restricted:

PAGE 37 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

11. Lift the Rear Inlay from the Rear Housing.

Motorola Mobility Confidential Restricted:

PAGE 38 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear-Facing Imager Bezel Removal

NOTE
The Rear-Facing Imager Bezel can be
recovered and reused after removal.

Use the Blackstick to push the Rear-Facing Imager

Bezel out of the Rear Inlay.

Motorola Mobility Confidential Restricted:

PAGE 39 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear-Facing Imager Lens Removal

Use the Thin Plastic Spudger to pry the Rear-Facing
Imager Lens from the Rear Housing.

NOTE
After you remove the Rear-Facing Imager
Lens, you cannot reuse it.

Motorola Mobility Confidential Restricted:

PAGE 40 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

DROID Logo Removal

NOTE
After you remove the DROID Logo, you
cannot reuse it.

1. Bend the bottom left corner of the Rear Inlay until

the left edge of the DROID Logo lifts from the
Rear Inlay.

2. Slide the Thin Plastic Spudger under the left

edge of the DROID Logo. Slide the Spudger
towards the right edge of the Logo until it lifts
from the Rear Inlay.

Motorola Mobility Confidential Restricted:

PAGE 41 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear Housing Removal

NOTE
The Rear Housing can be recovered
and reused after removal.

1. Use the flat end of the Blackstick to remove the

NFC Flex Stopper.

2. Use the flat end of the Blackstick to disconnect

the NFC Flex BtB Connector from the PCB.

3. Use the pointed end of the Blackstick to remove

the Earpiece Flex Stopper.

4. Use the flat end of the Blackstick to disconnect

the Earpiece Flex BtB Connector from the PCB.

Motorola Mobility Confidential Restricted:

PAGE 42 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

5. Remove the 17 3IP Screws from the Rear

Housing.

6. Press and hold the Power Key and Volume Key.

NOTE
The Side Keys will fall out when the Rear Housing
is removed from the phone.

7. Lift the side of the Rear Housing opposite the

Side Keys to remove it from the phone.

Motorola Mobility Confidential Restricted:

PAGE 43 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Side Key Removal

NOTE
The Side Keys can be recovered and
reused after removal.

Use the flat end of the Blackstick to remove the

Power Key and Volume Key from the Rear Housing.

Motorola Mobility Confidential Restricted:

PAGE 44 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Battery Disconnection
/// WARNING /// // CAUTION //
Failure to adhere to Safety Critical Note(s) may increase Handle the Battery Pack with care. If dropped to the
risk of rupture, burning, or failure to function safely when floor, it may be internally damaged and must be
used by the customer. Refer to the Battery Safety scrapped.
Guidelines.
Ensure Battery and its insulation are not damaged (e.g.
scratched, dented, punctured) prior to and throughout
assembly.
Prior to assembly, ensure Battery edges and surfaces
are not dented or deformed, and that fixtures and parts
that will contact the Battery are free of foreign material.
Ensure screws and screwdrivers do not contact the
Battery.

1. Lift the Heat Spreader from the Chassis.

Motorola Mobility Confidential Restricted:

PAGE 45 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

2. Remove the 2 3IP Screws from the Chassis.

3. Lift the Chassis from the phone.

NOTE
The Chassis can be recovered and
reused after removal.

4. Use the flat end of the Blackstick to disconnect

the Battery Flex BtB Connector from the PCB.

Motorola Mobility Confidential Restricted:

PAGE 46 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Front-Facing Imager Removal

NOTE
The Front-Facing Imager can be
recovered and reused after removal.

1. Use the flat end of the Blackstick to disconnect

the Front-Facing Imager BtB Connector.

2. Lift the Front-Facing Imager out of the pocket of

the Display.

Motorola Mobility Confidential Restricted:

PAGE 47 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Front-Facing Imager Gasket Removal

Use the Plastic Tweezers to remove the Front-Facing
Imager Gasket from the pocket of the Display.

NOTE
After you remove the Front-Facing
Imager Gasket, you cannot reuse it.

Motorola Mobility Confidential Restricted:

PAGE 48 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Earpiece Speaker Removal

Use the flat end of the Blackstick to pry the Earpiece
Speaker out of the pocket of the Display.

NOTE
After you remove the Earpiece
Speaker, you cannot reuse it.

Motorola Mobility Confidential Restricted:

PAGE 49 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Secondary-Microphone Grommet Removal

Use the Tweezers to remove the Secondary-
Microphone Grommet from the Display.

NOTE
After you remove the Secondary-
Microphone Grommet, you cannot reuse
it.

Motorola Mobility Confidential Restricted:

PAGE 50 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Battery Removal
/// WARNING /// // CAUTION //
Failure to adhere to Safety Critical Note(s) may increase Handle the Battery Pack with care. If dropped to the
risk of rupture, burning, or failure to function safely when floor, it may be internally damaged and must be
used by the customer. Refer to the Battery Safety scrapped.
Guidelines.
Ensure Battery and its insulation are not damaged (e.g.
scratched, dented, punctured) prior to and throughout
assembly.
Prior to assembly, ensure Battery edges and surfaces
are not dented or deformed, and that fixtures and parts
that will contact the Battery are free of foreign material.
Ensure screws and screwdrivers do not contact the
Battery.

NOTE
The Battery can be recovered and
reused after removal.

1. Slide the Thin Plastic Spudger between the

Battery and Display in the highlighted area to
separate the Battery Adhesive.

2. After the Battery Adhesive is separated from the

Display, lift the Battery from the Display.
3. If the Battery Adhesive remains attached, use
the Battery Pull Tab to aid in separating the
Battery from the Display.

Motorola Mobility Confidential Restricted:

PAGE 51 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

PCB Removal
NOTE
The PCB can be recovered and
reused after removal.

1. Remove the Kapton Tape from the Touch Flex

ZIF Connector.

NOTE
After you remove the Kapton Tape, you
cannot reuse it.

2. Use the flat end of the Blackstick to open the

Touch Flex ZIF Connector Door.
3. Remove the Touch Flex from the connector.

4. Use the Thin Plastic Spudger to separate the

Touch Flex from the PCB.

// CAUTION //
Use caution when lifting the Touch Flex from the
PCB. Damage to the Touch Flex may occur.

5. Use the flat end of the Blackstick to disconnect

the Side-Key Flex BtB Connector.

Motorola Mobility Confidential Restricted:

PAGE 52 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

6. Use the flat end of the Blackstick to lift the Coax

Cable from the retaining clips.

7. Use the flat end of the Blackstick to disconnect

the Coax Cable from the PCB.

8. Remove the Kapton Tape from the Display Flex

ZIF Connector.

NOTE
After you remove the Kapton Tape, you
cannot reuse it.

9. Use the flat end of the Blackstick to open the

Display Flex ZIF Connector Door.
10. Remove the Display Flex from the connector.

11. Lift the PCB from the Display.

// CAUTION //
Do not damage the Display Flex, Touch Flex, or
Coax Cable when removing the PCB.

Motorola Mobility Confidential Restricted:

PAGE 53 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Trim Ring Removal

NOTE
The Trim Ring can be recovered and
reused after removal.

1. Use the flat end of the Blackstick to pry the Trim

Ring away from the recess on the bottom side of
the Display.

2. Lift the two corners of the Trim Ring away from

the bottom of the Display.

3. Continue lifting the Trim Ring away from both

sides of the Display to disengage the 3 snaps.

4. Lift the Trim Ring away from the Display.

Motorola Mobility Confidential Restricted:

PAGE 54 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

IR LED Flex Removal

NOTE
The IR LED Flex can be recovered
and reused after removal.

1. Use the Tweezers to remove the Kapton Tape

from the IR LED Flex ZIF Connector.

NOTE
After you remove the Kapton Tape, you
cannot reuse it.

2. Use the flat end of the Blackstick to open the IR

LED Flex ZIF Connector door.

3. Remove the IR LED Flex from the connector.

Motorola Mobility Confidential Restricted:

PAGE 55 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

IR LED Grommet Removal

Use the Tweezers to remove the IR LED Grommet
from the PCB.

NOTE
After you remove the IR LED Grommet,
you cannot reuse it.

Motorola Mobility Confidential Restricted:

PAGE 56 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Coax Cable Removal

NOTE
The Coax Cable can be recovered
and reused after removal.

Pull up on the Coax Cable to disconnect it from the

PCB.

Motorola Mobility Confidential Restricted:

PAGE 57 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear-Facing Imager Removal

NOTE
The Rear-Facing Imager can be
recovered and reused after removal.

1. Use the Tweezers to remove the Kapton Tape

from the Rear-Facing Imager ZIF Connector.

NOTE
After you remove the Kapton Tape, you
cannot reuse it.

2. Use the flat end of the Blackstick to open the

Rear-Facing Imager ZIF Connector door.

3. Remove the Rear-Facing Imager from the

connector.

Motorola Mobility Confidential Restricted:

PAGE 58 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Proximity Grommet Removal

Use the Tweezers to remove the Proximity Grommet
from the PCB.

NOTE
After you remove the Proximity Grommet,
you cannot reuse it.

Motorola Mobility Confidential Restricted:

PAGE 59 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Microphone Grommet Removal

Use the Tweezers to remove the 4 Microphone
Grommets from the PCB.

NOTE
After you remove the Microphone
Grommets, you cannot reuse them.

Motorola Mobility Confidential Restricted:

PAGE 60 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Loudspeaker Removal
Use the flat end of the Blackstick to pry the
Loudspeaker from the Rear Housing.

NOTE
After you remove the Loudspeaker, you
cannot reuse it.

Motorola Mobility Confidential Restricted:

PAGE 61 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Vibrator Removal
NOTE
The Vibrator can be recovered and
reused after removal.

1. Hold the Retaining Tab open.

2. With the Retaining Tab open, push the Vibrator
out of the pocket of the Rear Housing.

Motorola Mobility Confidential Restricted:

PAGE 62 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Headset Jack Removal

NOTE
The Headset Jack and Headset Jack
Gasket can be recovered and reused
after removal.

Use the flat end of the Blackstick to pry the Headset

Jack from the pocket of the Rear Housing.

NOTE
The Headset Jack Gasket is adhered to and
removed along with the Headset Jack.

Motorola Mobility Confidential Restricted:

PAGE 63 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

NFC Antenna Removal

Using both hands, push the NFC Antenna out of the
Rear Housing.

NOTE
After you remove the NFC Antenna, you
cannot reuse it.

Motorola Mobility Confidential Restricted:

PAGE 64 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

PARTS REFRESH
Tools Required for Parts Refresh
The following tools are required for parts refresh of the DROID TURBO 2 / Moto X Force phone.

Description Part # Image

Blackstick --

Thin Plastic Spudger 0-00-00-40826

Tweezers (Plastic or Plastic-Tipped) -- --

ESD Mat and Wrist Strap -- --
Gloves or Finger Collets -- --
Isopropyl (ISP) Alcohol -- --

Motorola Mobility Confidential Restricted:

PAGE 65 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Battery Cleaning
/// WARNING /// // CAUTION //
Failure to adhere to Safety Critical Note(s) may increase Handle the Battery Pack with care. If dropped to the
risk of rupture, burning, or failure to function safely when floor, it may be internally damaged and must be
used by the customer. Refer to the Battery Safety scrapped.
Guidelines.
Ensure Battery and its insulation are not damaged (e.g.
scratched, dented, punctured) prior to and throughout
assembly.
Prior to assembly, ensure Battery edges and surfaces
are not dented or deformed, and that fixtures and parts
that will contact the Battery are free of foreign material.
Ensure screws and screwdrivers do not contact the
Battery.

1. Use the Blackstick and ISP Alcohol to remove

the Heat Spreader and any remaining adhesive
from the Battery.

// CAUTION //
To prevent damage, do not allow sharp tools or
screws to come in contact with the Battery.

Motorola Mobility Confidential Restricted:

PAGE 66 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

2. Use the Blackstick and ISP Alcohol to remove

any remaining adhesive from the Battery.

// CAUTION //
To prevent damage, do not allow sharp tools or
screws to come in contact with the Battery.

3. Inspect the Battery to verify it is not creased,

crushed, or punctured.
4. If the Battery foil pack is wrinkled, slide the flat
edge of the Blackstick against the foil pack to
smooth out all wrinkles.

// CAUTION //
To prevent damage, do not allow sharp tools or
screws to come in contact with the Battery.

Motorola Mobility Confidential Restricted:

PAGE 67 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

PCB Cleaning
1. Use the Blackstick and ISP Alcohol to remove
any remaining adhesive from the PCB.

2. Use the Blackstick and ISP Alcohol to remove

the Display Flex ZIF Connector Pad.

3. Use the Blackstick and ISP Alcohol to remove

the Rear-Facing Imager ZIF Connector Pad.

Motorola Mobility Confidential Restricted:

PAGE 68 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

4. Use the Blackstick and ISP Alcohol to remove

the IC Copper Tape.

5. Use the Blackstick and ISP Alcohol to remove

the PCB Shield Copper Tape.

Motorola Mobility Confidential Restricted:

PAGE 69 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear Housing Cleaning

1. Use the Blackstick and ISP Alcohol to remove
any remaining adhesive left by the NFC Antenna.

NOTE
This step is applicable only if the NFC Antenna
was removed during disassembly.

2. Use the Blackstick and ISP Alcohol to remove

any remaining adhesive left by the Rear Inlay on
the Rear Housing and NFC Antenna.

3. Use the Blackstick and ISP Alcohol to remove

any remaining adhesive left by the Headset
Jack.

Motorola Mobility Confidential Restricted:

PAGE 70 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

4. Use the Blackstick and ISP Alcohol to remove

the Loudspeaker Gasket.

Motorola Mobility Confidential Restricted:

PAGE 71 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear Inlay Cleaning

Use the Blackstick and ISP Alcohol to remove any
remaining adhesive from the Rear Inlay.

Motorola Mobility Confidential Restricted:

PAGE 72 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

ASSEMBLY
Assembly Map
Main-
PCB ZIF Connector Proximity IR LED Rear-Facing
Microphone IR LED Flex Coax Cable PCB
Preparation Pads Grommet Grommet Imager
Grommets

Secondary-
Front-Facing Earpiece Battery
Side-Key Flex Microphone Battery Display
Imager Speaker Adhesive
Grommet

Loudspeaker
WDL Loudspeaker Vibrator NFC Antenna Headset Jack LED Flash Rear Housing
Gasket

Side Keys

Rear-Facing Rear-Facing
DROID Logo Rear Inlay
Imager Lens Imager Bezel

SIM/SD Tray

Audio Bezel

DLN Liner

Motorola Mobility Confidential Restricted:

PAGE 73 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Tools Required for Assembly

The following tools are required to assemble the DROID TURBO 2 / Moto X Force phone.

Description Part # Picture / Drawing

Universal Press Fixture 3-00-A3-10000

Universal Press Weights 3-00-E5-10000

Universal Nest 3-00-A7-10000

Bounce PCB Assembly Fixture 3-00-D7-10000

Bounce Earpiece Deco Press Fixture 3-00-D8-10000

Motorola Mobility Confidential Restricted:

PAGE 74 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Description Part # Picture / Drawing

Bounce Audio Gasket Alignment Fixture 3-00-D9-10000

Bounce Inlay Adhesive Fixture 3-00-E8-10000

Bounce Chassis Screw Guide 3-00-F6-10000

Bounce Audio Bezel Press Tool 3-00-F7-10000

3IP Torx Bit --

Torque Driver (Adjustable) --

Tweezers (Plastic or Plastic-Tipped) -- --

ESD Mat and Wrist Strap -- --
Gloves or Finger Collets -- --
Isopropyl (ISP) Alcohol -- --
Cotton Swabs -- --
Compressed Air Spray Can -- --

Motorola Mobility Confidential Restricted:

PAGE 75 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Description Part # Picture / Drawing

3M AP-111 Adhesion Promoter --

Motorola Mobility Confidential Restricted:

PAGE 76 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear Housing WDL Assembly

Description Reference #
ASSY,HSG,REAR,METALLIC DK GRY 1
ASSY,HSG,REAR,TIN SILVER,KINZIE
ASSY,HSG,REAR,CHAMPAGNE,KINZIE
ASSY,HSG,REAR,RED,KINZIE
LBL,WATER, DETECT 2

Place the Rear Housing WDL near the SIM/SD Card

slot as shown.

Motorola Mobility Confidential Restricted:

PAGE 77 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

PCB Preparation

Description Reference #
ASSY,PWA,MN,BOUNCE VZW 1
ASSY,PWA,MN,BOUNCE,ROW
ASSY,PWA,MN,64 GB,BOUNCE,VZW
ASSY,PWA,MN,64 GB,BOUNCE,ROW
ASSY,PWA,MN,32 GB,BOUNCE,CHINA,ROW
DIE CUT,ADHESIVE,COPPER TAPE,MSM8994 2
DIE CUT,ADHES,COP TAPE,PM8994 3
DIE CUT,ADHESIVE,PCB-CHASSIS 4
LBL,WATER, DETECT 5

Motorola Mobility Confidential Restricted:

PAGE 78 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

1. Place the PCB into the Bounce PCB Assembly

Fixture (3-00-D7-10000).

2. Remove the PCB Shield Copper Tape from the

carrier.
3. Place the PCB Shield Copper Tape into the
fixture over the PCB, using the pins in the fixture
to align it.
4. Press down on the PCB Shield Copper Tape for
5 seconds to secure it to the PCB Shield.

5. Remove the PCB from the fixture.

6. Remove the remaining liner from the PCB Shield
Copper Tape.
7. Use the Blackstick to adhere the edges of the
PCB Shield Copper Tape to the PCB Shield.

Motorola Mobility Confidential Restricted:

PAGE 79 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

8. Place the PCB into the fixture.

9. Remove the PCB Adhesive from the carrier.

10. Place the PCB Adhesive into the fixture, using
the pins in the fixture to align it.
11. Press down on the PCB Adhesive for 5 seconds
to secure it to the PCB.

12. Remove the PCB from the fixture.

13. Remove the remaining liner from the PCB
Adhesive.

Motorola Mobility Confidential Restricted:

PAGE 80 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

14. Place the PCB into the fixture.

15. Remove the IC Copper Tape from the carrier.

16. Place the IC Copper Tape into the fixture, using
the pins in the fixture to align it.
17. Press down on the IC Copper Tape for 5
seconds to secure it to the IC Shield.

18. Remove the PCB from the fixture.

19. Remove the remaining liner from the IC Copper
Tape.
20. Use the Blackstick to adhere the edges of the IC
Copper Tape to the IC Shield.

Motorola Mobility Confidential Restricted:

PAGE 81 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

21. Place the PCB WDL on the PCB in the location

shown.
22. Press down on the PCB WDL for 5 seconds to
secure it to the PCB.

Motorola Mobility Confidential Restricted:

PAGE 82 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

ZIF Connector Pad Assembly

Description Reference #
ASSY,PWA,MN,BOUNCE VZW 1
ASSY,PWA,MN,BOUNCE,ROW
ASSY,PWA,MN,64 GB,BOUNCE,VZW
ASSY,PWA,MN,64 GB,BOUNCE,ROW
ASSY,PWA,MN,32 GB,BOUNCE,CHINA,ROW
PAD,CONNECTOR,REAR IMGR 2
Display Flex ZIF Connector Pad 3

1. Place the Display Flex ZIF Connector Pad on the

PCB, using the etched markings on the PCB to
align it.

Motorola Mobility Confidential Restricted:

PAGE 83 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

2. Place the Rear-Facing Imager ZIF Connector

Pad on the PCB, using the etched markings on
the PCB to align it.

Motorola Mobility Confidential Restricted:

PAGE 84 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Proximity Grommet Assembly

Description Reference #
ASSY,PWA,MN,BOUNCE VZW 1
ASSY,PWA,MN,BOUNCE,ROW
ASSY,PWA,MN,64 GB,BOUNCE,VZW
ASSY,PWA,MN,64 GB,BOUNCE,ROW
ASSY,PWA,MN,32 GB,BOUNCE,CHINA,ROW
GROM,SENSOR,KINZIE 2

1. Use the Plastic Tweezers to place the Proximity

Grommet in position on the Proximity Sensor.

2. Verify the Proximity Grommet is flush with the

Proximity Sensor.

Motorola Mobility Confidential Restricted:

PAGE 85 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

IR LED Grommet Assembly

Description Reference #
ASSY,PWA,MN,BOUNCE VZW 1
ASSY,PWA,MN,BOUNCE,ROW
ASSY,PWA,MN,64 GB,BOUNCE,VZW
ASSY,PWA,MN,64 GB,BOUNCE,ROW
ASSY,PWA,MN,32 GB,BOUNCE,CHINA,ROW
SEAL,IR LED 2

1. Use the Plastic Tweezers to place the IR LED

Grommet in position on the IR LED.

2. Verify the IR LED Grommet is flush with the IR

LED.

Motorola Mobility Confidential Restricted:

PAGE 86 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Main-Microphone Grommet Assembly

Description Reference #
ASSY,PWA,MN,BOUNCE VZW 1
ASSY,PWA,MN,BOUNCE,ROW
ASSY,PWA,MN,64 GB,BOUNCE,VZW
ASSY,PWA,MN,64 GB,BOUNCE,ROW
ASSY,PWA,MN,32 GB,BOUNCE,CHINA,ROW
GROM,MIC PURPLE 2 (qty 4)
GROM,MIC ORANGE

Motorola Mobility Confidential Restricted:

PAGE 87 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

1. Use the Plastic Tweezers to place the 4 Main-

Microphone Grommets in position on the
Microphones.

2. Verify all 4 Microphone Grommets are flush with

the PCB.

NOTE
Only 2 of the 4 Microphone Grommets are shown.
The orientation of all 4 grommets is the same.

Motorola Mobility Confidential Restricted:

PAGE 88 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

IR LED Flex Assembly

Description Reference #
ASSY,PWA,MN,BOUNCE VZW 1
ASSY,PWA,MN,BOUNCE,ROW
ASSY,PWA,MN,64 GB,BOUNCE,VZW
ASSY,PWA,MN,64 GB,BOUNCE,ROW
ASSY,PWA,MN,32 GB,BOUNCE,CHINA,ROW
ASSY,FLXCKT,IR LED,KINZIE 2

1. Insert the IR LED Flex into the IR LED Flex ZIF

Connector, using the white line as a guide for
insertion depth.
2. Slide a fingertip across the ZIF Connector Door
to close it.
3. Place Kapton Tape over the IR LED Flex ZIF
Connector.

Motorola Mobility Confidential Restricted:

PAGE 89 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear-Facing Imager Assembly

Description Reference #
ASSY,PWA,MN,BOUNCE VZW 1
ASSY,PWA,MN,BOUNCE,ROW
ASSY,PWA,MN,64 GB,BOUNCE,VZW
ASSY,PWA,MN,64 GB,BOUNCE,ROW
ASSY,PWA,MN,32 GB,BOUNCE,CHINA,ROW
ASSY,FLXCKT,CAMERA,REAR FACING 21MP IMAGER,KINZIE 2

1. Insert the Rear-Facing Imager Flex into the

Rear-Facing Imager ZIF Connector.
2. Slide a fingertip across the ZIF Connector Door
to close it.
3. Place Kapton Tape over the Rear-Facing Imager
ZIF Connector.

Motorola Mobility Confidential Restricted:

PAGE 90 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Trim Ring Assembly

Description Reference #
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,BLACK,ROW,KINZIE 1
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,WHITE,ROW,KINZIE
HSG,FRNT RIM,DECORATED,BLACK 2
HSG,FRNT RIM,DECORATED,WHITE

1. Place the top side of the Trim Ring onto the

Display.

Motorola Mobility Confidential Restricted:

PAGE 91 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

2. Push the left side of the Trim Ring into the

recess of the Display and engage the snap.

Motorola Mobility Confidential Restricted:

PAGE 92 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

3. Push the right side of the Trim Ring into the

recess of the Display and engage the 2 snaps.

4. Push the USB Connector side of the Trim Ring

into the recess of the Display.

Motorola Mobility Confidential Restricted:

PAGE 93 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

5. Verify the Trim Ring is seated in the recess of

the Display, and no light is visible between the
Trim Ring and Display.

Motorola Mobility Confidential Restricted:

PAGE 94 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Coax Cable Assembly

Description Reference #
ASSY,PWA,MN,BOUNCE VZW 1
ASSY,PWA,MN,BOUNCE,ROW
ASSY,PWA,MN,64 GB,BOUNCE,VZW
ASSY,PWA,MN,64 GB,BOUNCE,ROW
ASSY,PWA,MN,32 GB,BOUNCE,CHINA,ROW
CABLE,COAX 2

// CAUTION //
The Coax Cable must be assembled to the PCB
with the small cable shield towards the PCB.

Motorola Mobility Confidential Restricted:

PAGE 95 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

1. Place one end of the Coax Cable over the

connector on the PCB.
2. Press down on the Coax Cable until it snaps in
place.

3. Push the Coax Cable and small cable shield into

the guide on the PCB.

// CAUTION //
Make sure the Coax Cable is assembled with the
small cable shield inserted in the guide on the
PCB. If the Coax Cable is assembled as shown,
remove it and connect the opposite end of the
cable.

Motorola Mobility Confidential Restricted:

PAGE 96 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

PCB Assembly

Description Reference #
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,BLACK,ROW,KINZIE 1
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,WHITE,ROW,KINZIE
ASSY,PWA,MN,BOUNCE VZW 2
ASSY,PWA,MN,BOUNCE,ROW
ASSY,PWA,MN,64 GB,BOUNCE,VZW
ASSY,PWA,MN,64 GB,BOUNCE,ROW
ASSY,PWA,MN,32 GB,BOUNCE,CHINA,ROW

1. Insert the Display Flex into the Display Flex ZIF

Connector.
2. Align the PCB to the Display along the edge
opposite the Side Keys.

Motorola Mobility Confidential Restricted:

PAGE 97 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

3. Lower the PCB into the Display, keeping the

Side-Key Flex and Touch Flex from tucking
underneath the PCB.

Motorola Mobility Confidential Restricted:

PAGE 98 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

4. Remove the adhesive liner from the Touch Flex

if present.
5. Fold the Touch Flex down onto the PCB, aligning
it to the etched markings on the PCB.

6. Insert the Touch Flex into the Touch Flex ZIF

Connector. Use the white line as a guide for
insertion depth.
7. Slide a fingertip across the ZIF Connector Door
to close it.
8. Place Kapton tape over the Touch Flex ZIF
Connector Door.

Motorola Mobility Confidential Restricted:

PAGE 99 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

9. Verify the Display Flex is inserted in the Display

Flex ZIF Connector. Use the white line as a
guide for insertion depth.
10. Slide a fingertip across the ZIF Connector Door
to close it.
11. Place Kapton Tape over the Display Flex ZIF
Connector.

12. Press down on the Side-Key Flex to connect the

Side-Key Flex BtB Connector.

13. Place the IR LED Flex in position on the Display.

Use the post in the Display to align the flex.
14. Push the IR LED Flex Sensor into the pocket of
the Display.

Motorola Mobility Confidential Restricted:

PAGE 100 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

15. Place the end of the Coax Cable over the

connector on the PCB.
16. Press down on the Coax Cable until it snaps in
place.

17. Push the Coax Cable and large cable shield into
the guide on the PCB.

Motorola Mobility Confidential Restricted:

PAGE 101 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Earpiece Speaker Assembly

Description Reference #
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,BLACK,ROW,KINZIE 1
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,WHITE,ROW,KINZIE
TRANSDUCER,OTHR,6X12X3,6X12X3MM RCVR F0=200HZ, AAC 2

1. Remove the Earpiece Speaker adhesive liner.

2. Place the Earpiece Speaker in the pocket of the
Display, with the raised speaker contacts facing
away from the top edge of the phone as shown.
3. Press down on the Earpiece Speaker for 5
seconds to secure it to the Display.

Motorola Mobility Confidential Restricted:

PAGE 102 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Front-Facing Imager Assembly

Description Reference #
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,BLACK,ROW,KINZIE 1
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,WHITE,ROW,KINZIE
SEAL,O-RING,FRONT IMGR 2
ASSY,FLXCKT,5MP IMAGER,KINZIE 3

1. Place the Front-Facing Imager Gasket over the

Front Facing Imager as shown.

Motorola Mobility Confidential Restricted:

PAGE 103 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

2. Spray the Front-Facing Imager pocket in the

Display with compressed air to remove any dust
or foreign material.

3. Remove the protective liner from the Front-

Facing Imager if present.
4. Place the Front-Facing Imager into the pocket of
the Display.

5. Press down on the Front-Facing Imager BtB

Connector to connect it to the PCB.

Motorola Mobility Confidential Restricted:

PAGE 104 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Secondary-Microphone Grommet Assembly

Description Reference #
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,BLACK,ROW,KINZIE 1
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,WHITE,ROW,KINZIE
GROM,SEAL,MIC 5 2

1. Use the Tweezers to place the Secondary-

Microphone Grommet into position on the
Display.

2. Verify the grommet is positioned as shown.

3. Press down on the Secondary-Microphone
Grommet for 5 seconds to secure it to the
Display.

Motorola Mobility Confidential Restricted:

PAGE 105 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Battery Adhesive Assembly

Description Reference #
ASSY,BAT,LI POLY,FB55,3760MAH,LG CHEM 1
DIE CUT,ADHES,BAT 2

1. Remove the Battery Adhesive from the carrier.

2. Place the Battery Adhesive onto the Battery.
Align the flat edge of the Battery Adhesive liner
with the black Battery liner tape, and the curved
edge of the adhesive with the text on the Battery
foil pack. The Battery Adhesive should not
overlap the black Battery liner.
3. Press down on the Battery Adhesive for 5
seconds to secure it to the Battery.

Motorola Mobility Confidential Restricted:

PAGE 106 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Battery Assembly

Description Reference #
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,BLACK,ROW,KINZIE 1
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,WHITE,ROW,KINZIE
ASSY,BAT,LI POLY,FB55,3760MAH,LG CHEM 2
ASSY,CHAS,REAR,KINZIE 3
SCR,MACH,M1.4 4 (qty 2)

/// WARNING /// // CAUTION //

Failure to adhere to Safety Critical Note(s) may increase Handle the Battery Pack with care. If dropped to the
risk of rupture, burning, or failure to function safely when floor, it may be internally damaged and must be
used by the customer. Refer to the Battery Safety scrapped.
Guidelines.
Ensure Battery and its insulation are not damaged (e.g.
scratched, dented, punctured) prior to and throughout
assembly.
Prior to assembly, ensure Battery edges and surfaces
are not dented or deformed, and that fixtures and parts
that will contact the Battery are free of foreign material.
Ensure screws and screwdrivers do not contact the
Battery.

Motorola Mobility Confidential Restricted:

PAGE 107 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

1. Remove the adhesive liner from the Battery

Adhesive.
2. Place the Battery into the pocket of the Display,
sliding the top-right corner of the Battery under
the SIM/SD Tray slot.

3. Press down on the Battery for 5 seconds to

secure it to the Display.

Motorola Mobility Confidential Restricted:

PAGE 108 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

4. Press down on the Battery Flex BtB Connector

to connect it to the PCB.

5. Place the Chassis over the PCB, using the screw

holes in the Chassis to align it.

6. Place the Bounce Chassis Screw Guide

(3-00-F6-10000) over the Chassis. Slide the
fixture toward the top of the phone until it is
aligned over the screw holes.

7. Tighten the 2 3IP Screws to 1.0 in-lbs

(0.11 N m).

Motorola Mobility Confidential Restricted:

PAGE 109 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Heatspreader Assembly

Description Reference #
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,BLACK,ROW,KINZIE 1
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,WHITE,ROW,KINZIE
DIE CUT,THRM SPREAD,MSM,KINZIE 2

/// WARNING /// // CAUTION //

Failure to adhere to Safety Critical Note(s) may increase Handle the Battery Pack with care. If dropped to the
risk of rupture, burning, or failure to function safely when floor, it may be internally damaged and must be
used by the customer. Refer to the Battery Safety scrapped.
Guidelines.
Ensure Battery and its insulation are not damaged (e.g.
scratched, dented, punctured) prior to and throughout
assembly.
Prior to assembly, ensure Battery edges and surfaces
are not dented or deformed, and that fixtures and parts
that will contact the Battery are free of foreign material.
Ensure screws and screwdrivers do not contact the
Battery.

Motorola Mobility Confidential Restricted:

PAGE 110 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

1. Remove the Heatspreader adhesive liner.

2. Place the Heatspreader over the Battery and
Chassis. Align the top and left sides to the raised
features of the Battery.

3. Press down on the Heatspreader for 5 seconds

to secure it to the Battery and Chassis.

Motorola Mobility Confidential Restricted:

PAGE 111 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

NFC Antenna Assembly

Description Reference #
ASSY,HSG,REAR,METALLIC DK GRY 1
ASSY,HSG,REAR,TIN SILVER,KINZIE
ASSY,HSG,REAR,CHAMPAGNE,KINZIE
ASSY,HSG,REAR,RED,KINZIE
FLX,NFC,WLC 2

1. Remove the NFC Antenna adhesive liner.

2. Place the NFC Antenna into the cutout area of
the Rear Housing. Use the posts in the Rear
Housing to align the antenna.

Motorola Mobility Confidential Restricted:

PAGE 112 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

3. Apply manual pressure to the NFC Antenna as

follows:
• Place both thumbs on point 1 and slide them
out to point 2.
2 1 2
// CAUTION //
Do not apply pressure to the LED Flash Flex.
Apply pressure to the NFC Antenna below the LED
Flash Flex.

• Place both thumbs on point 2 and slide them

down to point 3.

3 3

Motorola Mobility Confidential Restricted:

PAGE 113 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Vibrator Assembly

Description Reference #
ASSY,HSG,REAR,METALLIC DK GRY 1
ASSY,HSG,REAR,TIN SILVER,KINZIE
ASSY,HSG,REAR,CHAMPAGNE,KINZIE
ASSY,HSG,REAR,RED,KINZIE
ALERT DEVICE,VIBR,MOTOR, ROTARY, 11.75 MM X X 4.55 MM MOTOR BODY 2

1. Place the Vibrator into the pocket of the Rear

Housing.

Motorola Mobility Confidential Restricted:

PAGE 114 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

2. Verify the Vibrator is fully seated in the pocket of

the Rear Housing.

Motorola Mobility Confidential Restricted:

PAGE 115 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Headset Jack Assembly

Description Reference #
ASSY,HSG,REAR,METALLIC DK GRY 1
ASSY,HSG,REAR,TIN SILVER,KINZIE
ASSY,HSG,REAR,CHAMPAGNE,KINZIE
ASSY,HSG,REAR,RED,KINZIE
CONN,JACK,HEADSET,3.5 MM DIA 2

1. Remove the Headset Jack adhesive liner.

2. Place the Headset Jack into the pocket of the
Rear Housing.
3. Press down on the Headset Jack for 5 seconds
to secure it in the Rear Housing.

// CAUTION //
Do not damage the Headset Jack contacts when
pressing it into the Rear Housing.

Motorola Mobility Confidential Restricted:

PAGE 116 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

4. Verify the Headset Jack is flush to the edges of

the pocket of the Rear Housing.

Motorola Mobility Confidential Restricted:

PAGE 117 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Loudspeaker Assembly

Description Reference #
ASSY,HSG,REAR,METALLIC DK GRY 1
ASSY,HSG,REAR,TIN SILVER,KINZIE
ASSY,HSG,REAR,CHAMPAGNE,KINZIE
ASSY,HSG,REAR,RED,KINZIE
TRANSDUCER,POLYPHONIC,13X18X2P5 2

1. Remove the Loudspeaker Adhesive from the

carrier.
2. Place the Loudspeaker Adhesive into the
Bounce Audio Gasket Alignment Fixture (3-00-
D9-10000), using the pins in the fixture to align it.

Motorola Mobility Confidential Restricted:

PAGE 118 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

3. Place the Rear Housing into the fixture over the

Loudspeaker Adhesive, using the pins in the
fixture to align it.
4. Press down on the entire Rear Housing for 5
seconds to secure the adhesive.
5. Remove the Rear Housing from the fixture.

6. Remove the adhesive liner from the

Loudspeaker Adhesive.

7. Place the Loudspeaker into the pocket of the

Rear Housing.
8. Press down on the Loudspeaker for 5 seconds to
secure it to the Rear Housing.

Motorola Mobility Confidential Restricted:

PAGE 119 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear Housing Assembly

Description Reference #
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,BLACK,ROW,KINZIE 1
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,WHITE,ROW,KINZIE
ASSY,HSG,REAR,METALLIC DK GRY 2
ASSY,HSG,REAR,TIN SILVER,KINZIE
ASSY,HSG,REAR,CHAMPAGNE,KINZIE
ASSY,HSG,REAR,RED,KINZIE
BTN,POWER,GRAPHITE GRAY,KINZIE 3
BTN,VOLUME,GRAPHITE GRAY,KINZIE 4
SCR,MACH,M1.4 5 (qty 19)
ASSY,HSG,STOPPER,EARPIECE/FLASH,KINZIE 6
ASSY,HSG,STOPPER,NFC CONN 7

1. Remove the protective liners from the Rear-

Facing Imager and Loudspeaker Gasket opening
if present.

Motorola Mobility Confidential Restricted:

PAGE 120 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

2. Insert the Side Keys into the slots of the Rear

Housing. Orient the Side Keys as shown.
3. Push the Side Keys into the slots until they are
flush with the edge of the Rear Housing.

4. Place the Rear Housing over the phone. Place

the key side of the Rear Housing over the phone
first, then lower the side opposite the Side Keys
into position.

5. Verify the profiles of the Side Keys are visible.

The Side Keys should no longer be flush with the
edge of the Rear Housing.

6. Tighten 3IP Screw #1 to 1.0 in-lbs

(0.11N m).
7. Press the Power Key and Volume Key several
times to verify the tactile response.
8. Tighten 3IP Screw #2 to 1.0 in-lbs
(0.11N m).
1 2

Motorola Mobility Confidential Restricted:

PAGE 121 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

9. Press down on the USB Connector side of the

Rear Housing to engage the snaps.

10. Tighten the 17 3IP screws to 1.0 in-lbs

(0.11N m) in the order shown.

13 11 7 1 9 3
6

15
17

14
16

5 12 8 10 2 4

Motorola Mobility Confidential Restricted:

PAGE 122 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

11. Press down on the Flash Flex BtB Connector to

connect it to the PCB.
12. Press down on the NFC Antenna BtB Connector
to connect it to the PCB.

13. Insert the Flash Flex Stopper into the opening of

the Rear Housing. The stopper must be inserted
at the angle shown.
14. Press down on the Flash Flex Stopper until it
snaps into place.

15. Insert the NFC Flex Stopper into the opening of

the Rear Housing. The stopper must be inserted
at the angle shown.
16. Press down on the NFC Flex Stopper until it
snaps into place.

Motorola Mobility Confidential Restricted:

PAGE 123 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear-Facing Imager Lens Assembly

Description Reference #
ASSY,HSG,REAR,METALLIC DK GRY 1
ASSY,HSG,REAR,TIN SILVER,KINZIE
ASSY,HSG,REAR,CHAMPAGNE,KINZIE
ASSY,HSG,REAR,RED,KINZIE
LENS,IMAGER,REAR 2

1. Remove the adhesive liner from the Rear-Facing

Imager Lens.
2. Place the Rear-Facing Imager Lens on the Rear
Housing, using the raised features to align the
lens.

NOTE
The Rear-Facing Imager Lens can be placed by
hand or using the Plastic Tweezers.

3. Press down on the Rear-Facing Imager Lens for

5 seconds to secure it to the Rear Housing.

Motorola Mobility Confidential Restricted:

PAGE 124 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Rear Inlay Assembly

Description Reference #
ASSY,HSG,REAR,METALLIC DK GRY 1
ASSY,HSG,REAR,TIN SILVER,KINZIE
ASSY,HSG,REAR,CHAMPAGNE,KINZIE
ASSY,HSG,REAR,RED,KINZIE
DIE CUT,ADHESIVE,INLAY,REAR COVER 2
ASSY,HSG,INLAY,CSR,BLACK,REAR COVER,ROW 3
ASSY,HSG,INLAY,CSR,WINTER WHITE,REAR COV
ASSY,HSG,INLAY,NYLON,BLACK,REAR CVR
ASSY,HSG,INLAY,NYLON,BLACK,ROW,REAR CVR
ASSY,HSG,INLAY,NYLON,GRAY,ROW,REAR CVR
BZL,DECO,REAR,METALLIC DK GRY 4
BZL,DECO,REAR,METALLIC SLVR
BZL,DECO,REAR,METALLIC RED
ASSY,CAMR DECO,METALLIC SLVR 5
ASSY,CAMR DECO,METALLIC DK GRY
ASSY,CAMR DECO,METALLIC CHMPGN
ASSY,CAMR DECO,BLACK
ASSY,DROID LOGO,DARK MTLC GRAY,KINZIE 6
ASSY,DROID LOGO,DARK MTLC SILVER,KINZIE
ASSY,DROID LOGO,METALLIC CHAMPAGNE,TALL,KINZIE
ASSY,DROID LOGO,DARK GRAY/BLACK,KINZIE

Motorola Mobility Confidential Restricted:

PAGE 125 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

1. Place the Inlay Adhesive into the Bounce Inlay

Adhesive Fixture (3-00-E8-10000), using the pin
in the fixture and the deco hole in the adhesive
to align it.
2. Remove the adhesive liner from the Inlay
Adhesive.

3. Place the Rear Inlay into the fixture over the

Inlay Adhesive, using the pin in the fixture and
the deco hole to align it.
11
4. Apply manual pressure to the Rear Inlay as 12 12
follows:
• Place both thumbs on point 1 and slide
them out to point 2. 9
10 10
• Place both thumbs on point 3 and slide
them out to point 4.
1
• Place both thumbs on point 5 and slide 2
2
them out to point 6.
• Place both thumbs on point 7 and slide
them out to point 8. 3
4 4
• Place both thumbs on point 9 and slide
them out to point 10.
• Place both thumbs on point 11 and slide 5
them out to point 12.
6 6

7
8 8

5. Remove the Rear Inlay from the fixture.

6. Place the Rear Inlay on a flat surface.

Motorola Mobility Confidential Restricted:

PAGE 126 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

7. Remove the adhesive liner from the Camera

Deco.
8. Place the Camera Deco on the Rear-Facing
Imager Bezel, aligning the Bezel Lens.
9. Press down on the Camera Deco for 5 seconds
to secure it to the Rear-Facing Imager Bezel.

10. Remove the Rear-Facing Imager Bezel adhesive

liner from the Rear Inlay.
11. Place the Rear-Facing Imager Bezel into
position on the Rear Inlay. Verify the Bezel Lens
is oriented toward the top of the Rear Inlay.
12. Press down on the Rear-Facing Imager Bezel
for 5 seconds to secure it to the Rear Inlay.

13. Use a cotton swab to apply 3M Adhesion

Promoter 111 to the Rear Housing in the
highlighted area.

Motorola Mobility Confidential Restricted:

PAGE 127 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

14. Verify the liners on the Rear Housing and Flash

Lens have been removed, if present.
15. Remove the remaining adhesive liner from the
Rear Inlay.
16. Beginning at the top corners, apply the Rear
Inlay to the Rear Housing.
17. Verify the Inlay is seated in all 4 corners and not
overlapping any of the Rear Housing edges.

18. Apply manual pressure to the Rear Inlay as

follows: 11
12 12
• Place both thumbs on point 1 and slide them
out to point 2.
• Place both thumbs on point 3 and slide them 9
out to point 4. 10 10
• Place both thumbs on point 5 and slide
them out to point 6.
1
• Place both thumbs on point 7 and slide 2 2
them out to point 8.
• Place both thumbs on point 9 and slide
them out to point 10.
3
4 4
• Place both thumbs on point 11 and slide
them out to point 12.
5
6 6

7
8 8

Motorola Mobility Confidential Restricted:

PAGE 128 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

19. Place both thumbs on point 1 and slide them

around the perimeter of the Rear Inlay to point 2. 1

20. Place the phone onto the Universal Nest (3-00-

A7-10000), with the Display side face up.

Motorola Mobility Confidential Restricted:

PAGE 129 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

21. Place the Universal Press Fixture (3-00-A3-

10000) onto the Universal Nest over the phone.

22. Place the brackets for the Universal Press

Weights onto the Universal Press Fixture.

23. While holding the Universal Press Fixture in

position, place the Universal Press Weights into
the brackets.

Motorola Mobility Confidential Restricted:

PAGE 130 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

24. Using both hands, press down on the phone

with the Universal Press Fixture at 500 N m for 5
seconds.
25. Repeat two more times.

26. Remove the adhesive liner from the DROID

Logo.
27. Place the DROID Logo in the recess in the Rear
Inlay. Align the left, straight edge of the Logo
first.

NOTE
The DROID Logo can be placed by hand or using
the Plastic Tweezers.

28. Press down on the DROID Logo for 5 seconds

to secure it to the Rear Inlay.

Motorola Mobility Confidential Restricted:

PAGE 131 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

Audio Deco Assembly

Description Reference #
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,BLACK,ROW,KINZIE 1
ASSY,HSG,LENS W/ FRNT HOUSING,PSA,WHITE,ROW,KINZIE
ASSY,HSG,AU DECO,T&R,METALLIC RED,KINZIE (REWORK) 2
BZL,AU DECO,METALLIC BLK (REWORK)
BZL,AU DECO,METALLIC SLVR (REWORK)
BZL,AU DECO,METALLIC DK GRY (REWORK)
ASSY,HSG,AU DECO,T&R,METALLIC RED,KINZIE (ORIGINAL)
BZL,AU DECO,METALLIC BLK (ORIGINAL)
BZL,AU DECO,METALLIC SLVR (ORIGINAL)
BZL,AU DECO,METALLIC DK GRY (ORIGINAL)

Motorola Mobility Confidential Restricted:

PAGE 132 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

NOTE
When the Display is new, assemble using an original
Audio Bezel. When the Display is reused, assemble
using a rework Audio Bezel, which has added features
on the tab.

Original Audio Bezel Rework Audio Bezel

1. Place the phone into the Bounce Earpiece Deco

Press Fixture (3-00-D8-10000).

2. Place the alignment lid on the fixture over the

Display, using the pins in the fixture to align it.

Motorola Mobility Confidential Restricted:

PAGE 133 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

3. Insert the Audio Bezel into the slot in the

alignment lid.

4. Use the Bounce Audio Bezel Press Tool

(3-00-F7-10000) to press the Audio Bezel into
the Display.

Motorola Mobility Confidential Restricted:

PAGE 134 Do not share without consent from Motorola
DROID TURBO 2 / Moto X Force
Level 2 – Service and Repair Manual

SIM/SD Tray Assembly

Description Reference #
ASSY,HSG,REAR,METALLIC DK GRY 1
ASSY,HSG,REAR,TIN SILVER,KINZIE
ASSY,HSG,REAR,CHAMPAGNE,KINZIE
ASSY,HSG,REAR,RED,KINZIE
ASSY,HSG,SIM DOOR, FULL FLOOR TRAY,DARK MTLC GRAY, KINZIE 2
ASSY,HSG,SIM DOOR,FULL FLOOR TRAY,LIGHT
ASSY,HSG,SIM DOOR, FULL FLOOR TRAY,SINGLE SIM,METALLIC DK GRAY
ASSY,HSG,SIM DOOR, FULL FLOOR TRAY,SINGLE SIM,METALLIC SILVER,KI
ASSY,HSG,SIM DOOR, FULL FLOOR TRAY,SINGLE SIM,METALLIC CHAMPAGNE
ASSY,HSG,SIM DOOR, FULL FLOOR TRAY,SINGLE SIM,RED,KINZIE

1. Insert the SIM/SD Tray into the Rear Housing

assembly. The small hole should be oriented
toward the Headset Jack.

2. Verify the SIM/SD Tray is flush with the Rear

Housing.

Motorola Mobility Confidential Restricted:

PAGE 135 Do not share without consent from Motorola