Hardware Maintenance Manual

Lenovo B580
Note: Before using this information and the product it supports, be sure to read the general information
under Appendix A “Notices” on page 95.

First Edition (May 2012)

© Copyright Lenovo 2012.

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration
“GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents

About this manual. . . . . . . . . . . iii Chapter 7. Removing and replacing a

FRU . . . . . . . . . . . . . . . . . . 43
Chapter 1. Safety information . . . . . 1 General guidelines . . . . . . . . . . . . . 43
General safety . . . . . . . . . . . . . . . 1 1010 Battery pack . . . . . . . . . . . . . 43
Electrical safety . . . . . . . . . . . . . . 2 1020 Bottom slot cover . . . . . . . . . . . 44
Safety inspection guide . . . . . . . . . . . 3 1030 Optical drive . . . . . . . . . . . . . 44
Handling devices that are sensitive to electrostatic 1040 Memory modules . . . . . . . . . . . 46
discharge. . . . . . . . . . . . . . . . . 3
1050 Hard disk drive assembly . . . . . . . . 47
Grounding requirements . . . . . . . . . . . 4
1060 PCI Express Mini Card for wireless LAN . . 49
Safety notices (multilingual translations) . . . . . 4
1070 mSATA solid state drive . . . . . . . . . 51
Laser compliance statement (multilingual
translations) . . . . . . . . . . . . . . . . 19 1080 Backup battery . . . . . . . . . . . . 52
1090 Keyboard . . . . . . . . . . . . . . 53
Chapter 2. Important service 1100 Keyboard bezel . . . . . . . . . . . . 55
information . . . . . . . . . . . . . . 27 1110 Fingerprint board and LED board . . . . . 58
Strategy for replacing FRUs . . . . . . . . . 27 1120 Power board and touch pad bracket . . . . 59
Strategy for replacing a hard disk drive . . . 28 1130 Microphone assembly . . . . . . . . . 60
Important notice for replacing a system 1140 I/O board . . . . . . . . . . . . . . 61
board . . . . . . . . . . . . . . . . 28 1150 System board assembly and USB board . . 62
Important information about replacing RoHS 1160 DC-in connector . . . . . . . . . . . . 65
compliant FRUs . . . . . . . . . . . . . . 28
1170 Thermal module . . . . . . . . . . . . 66
Chapter 3. General checkout . . . . . 29 1180 CPU . . . . . . . . . . . . . . . . 68
What to do first . . . . . . . . . . . . . . 29 1190 LCD unit . . . . . . . . . . . . . . . 69
Power system checkout . . . . . . . . . . . 30 1200 Speaker assembly . . . . . . . . . . . 71
Checking the ac power adapter . . . . . . 30 1210 Base cover . . . . . . . . . . . . . . 72
Checking operational charging . . . . . . 31 2010 LCD front bezel . . . . . . . . . . . . 73
Checking the battery pack . . . . . . . . 31 2020 Integrated camera . . . . . . . . . . . 74
2030 LCD panel, LCD cable, and hinges . . . . 75
Chapter 4. Related service 2040 Antenna assembly and LCD rear cover . . . 77
information . . . . . . . . . . . . . . 33
Recovering the computer settings . . . . . . . 33 Chapter 8. Locations . . . . . . . . . 79
Passwords . . . . . . . . . . . . . . . . 33 Front and right-side view. . . . . . . . . . . 79
Power-on password . . . . . . . . . . . 33 Bottom and left-side view . . . . . . . . . . 80
Supervisor password . . . . . . . . . . 33
Chapter 9. Parts list . . . . . . . . . . 81
Power management . . . . . . . . . . . . 34
Overall . . . . . . . . . . . . . . . . . . 82
Screen blank mode . . . . . . . . . . . 34
LCD FRUs . . . . . . . . . . . . . . . . 85
Sleep mode . . . . . . . . . . . . . . 34
Keyboard . . . . . . . . . . . . . . . . . 86
Hibernation mode . . . . . . . . . . . 34
Miscellaneous parts . . . . . . . . . . . . 88
Chapter 5. Lenovo B580 . . . . . . . . 37 ac power adapters . . . . . . . . . . . . . 89
Specifications . . . . . . . . . . . . . . . 37 Power cords . . . . . . . . . . . . . . . 90
Status indicators . . . . . . . . . . . . . . 38
Appendix A. Notices . . . . . . . . . . 95
Fn key combinations . . . . . . . . . . . . 39
Electronic emissions notices . . . . . . . . . 96
Chapter 6. FRU replacement Trademarks . . . . . . . . . . . . . . . . 96
notices . . . . . . . . . . . . . . . . 41
Screw notices . . . . . . . . . . . . . . . 41

© Copyright Lenovo 2012 i

ii Hardware Maintenance Manual
About this manual
This manual provides service and reference information for the following Lenovo® products.

Machine Machine type (MT)

Lenovo B580 4377, 20144

Use this manual to troubleshoot problems.

The manual is divided into the following sections:

• The common sections provide general information, guidelines, and safety information required for
servicing computers.
• The product-specific section includes service, reference, and product-specific parts information.

Important:
• This manual is intended only for trained service technicians who are familiar with Lenovo products. Use
this manual to troubleshoot problems effectively.
• Before servicing a Lenovo product, be sure to read all the information under Chapter 1 “Safety
information” on page 1 and Chapter 2 “Important service information” on page 27.

© Copyright Lenovo 2012 iii

iv Hardware Maintenance Manual
Chapter 1. Safety information
This chapter presents following safety information that you need to be familiar with before you service a
Lenovo Notebook.
• “General safety” on page 1
• “Electrical safety” on page 2
• “Safety inspection guide” on page 3
• “Handling devices that are sensitive to electrostatic discharge” on page 3
• “Grounding requirements” on page 4
• “Safety notices (multilingual translations)” on page 4
• “Laser compliance statement (multilingual translations)” on page 19

General safety
Follow these rules to ensure general safety:

• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you
think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, make sure that other service technicians and the customer's personnel are
not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing
the machine.
• Keep your toolcase away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your
sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8
centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing, because metal
objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device
that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan
louvers or cover them with labels or stickers.

© Copyright Lenovo 2012 1

Electrical safety
Observe the following rules when working on electrical equipment.

Important:
Use only approved tools and test equipment. Some hand tools have handles covered with a soft material
that does not insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to
decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.

Attention: Another person must be there to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.

Attention: An electrical shock can occur only when there is a complete circuit. By observing the above
rule, you may prevent a current from passing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages; Instructions for these
precautions are in the safety sections of maintenance information. Use extreme care when measuring
high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on when they are removed from their normal operating
places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
– Similar units to listed above
This practice ensures correct grounding of the units.
• If an electrical accident occurs:

2 Hardware Maintenance Manual

 – Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.

Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each
machine was designed and built, required safety items were installed to protect users and service technicians
from injury. This guide addresses only those items. You should use good judgment to identify potential
safety hazards due to attachment of non-Lenovo features or options not covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present:

• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware

To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning
of every service task. Begin the checks with the power off, and the power cord disconnected.

Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo
alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.

Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.

Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.

Chapter 1. Safety information 3

 2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.

When handling ESD-sensitive parts:

• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.

Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.

Safety notices (multilingual translations)

The safety notices in this section are provided in the following languages:
• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional Chinese

DANGER

DANGER

4 Hardware Maintenance Manual

DANGER

DANGER

DANGER

DANGER

DANGER

Chapter 1. Safety information 5

DANGER

6 Hardware Maintenance Manual

Chapter 1. Safety information 7
PERIGO

PERIGO

PERIGO

PERIGO

PERIGO

PERIGO

8 Hardware Maintenance Manual

PERIGO

PERIGO

DANGER

DANGER

DANGER

Chapter 1. Safety information 9

DANGER

DANGER

DANGER

DANGER

DANGER

VORSICHT

10 Hardware Maintenance Manual

VORSICHT

VORSICHT

VORSICHT

VORSICHT

Chapter 1. Safety information 11

VORSICHT

VORSICHT

VORSICHT

12 Hardware Maintenance Manual

Chapter 1. Safety information 13
14 Hardware Maintenance Manual
Chapter 1. Safety information 15
16 Hardware Maintenance Manual
Chapter 1. Safety information 17
18 Hardware Maintenance Manual
Laser compliance statement (multilingual translations)
The laser compliance statements in this section are provided in the following languages:
• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional Chinese

Chapter 1. Safety information 19

20 Hardware Maintenance Manual
Chapter 1. Safety information 21
22 Hardware Maintenance Manual
Chapter 1. Safety information 23
24 Hardware Maintenance Manual
Chapter 1. Safety information 25
26 Hardware Maintenance Manual
Chapter 2. Important service information
This chapter presents the following important service information that applies to all machine types supported
by this manual:
• “Strategy for replacing FRUs” on page 27
– “Strategy for replacing a hard disk drive” on page 28
– “Important notice for replacing a system board” on page 28
• “Important information about replacing RoHS compliant FRUs” on page 28

Important: BIOS and device driver fixes are customer-installable. The BIOS and device drivers are available
at http://www.lenovo.com/support.

Strategy for replacing FRUs

Before replacing parts:

Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs
listed in this manual.

After a system board is replaced, ensure that the latest BIOS is installed to the system board before
completing the service action.

To download software fixes, drivers, and BIOS, do the following:

1. Go to http://www.lenovo.com/support.
2. Click Download Drivers & Software. The Web site offers three options to begin your search:
• Search by product number
• Search through the product auto-detect function
• Search by product category
3. Follow the directions on the screen and install the necessary software.

Notes: If you need to improve the computer performance, you also could download and install the latest
BIOS utility from the Support Web site.
• Do not try to update the BIOS settings for any computer unless you have been trained and certified. An
untrained person runs the risk of damaging the computer.
• Before installing the latest utility, make sure that the battery is fully charged and an ac power adapter is
connected.
• Do not turn off or put your computer into sleep or hibernation until the update has been completed.
Otherwise, the system board might be damaged.

Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs:
• If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall
the original FRU before you continue.
• Some computers have both a processor board and a system board. If you are instructed to replace either
the processor board or the system board, and replacing one of them does not correct the problem,
reinstall that board, and then replace the other one.

© Copyright Lenovo 2012 27

• If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error.
Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change.
Replace only the FRU that changed the symptoms.

Strategy for replacing a hard disk drive

Always try to run a low-level format before replacing a hard disk drive (HDD). This will cause all customer data
on the hard disk to be lost. Be sure that the customer has a current backup of the data before doing this task.

Attention: The drive startup sequence in the computer you are servicing may have been changed. Be
extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect
drive, data or programs can be overwritten.

Important notice for replacing a system board

Some components mounted on a system board are very sensitive. Improper handling of a system board can
cause damage to those components, and may cause a system malfunction.

Attention: When handling a system board:

• Do not drop a system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.

Important information about replacing RoHS compliant FRUs

RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive
(2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS
requirements must be implemented on Lenovo products placed on the market after June 2006. Products
on the market before June 2006 are not required to have RoHS compliant parts. If the original FRU parts
are non-compliant, the replacement parts also can be non-compliant. That is, if the original FRU parts are
RoHS compliant, the replacement part also must be RoHS compliant.

Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified by the unique
FRU part numbers.

Lenovo plans to transit to RoHS compliance before the implementation date and expects its suppliers to be
ready to meet Lenovo’s requirements and schedule in the European Union. Products sold between 2005
and 2006 might contain some RoHS compliant FRUs. The following statement pertains to the products
with RoHS compliant FRUs.

RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS implementation date, the
failed RoHS compliant parts must be replaced with compliant parts and only the following FRUs can be
used: identified as compliant in the Hardware Maintenance Manual or direct substitutions can be used.
• Compliant FRUs identified in Hardware Maintenance Manual
• Direct substitutions with different FRU part numbers automatically shipped by the distribution center at
the time of order

For products shipped after June 2006

Current or original part Replacement FRU

Must be RoHS Must be RoHS

28 Hardware Maintenance Manual

Chapter 3. General checkout
This chapter presents following information:
• “What to do first” on page 29
• “Power system checkout” on page 30

Before you go to the checkout guide, be sure to read the following important notes.

Important notes:
• Only certified trained personnel should service the computer.
• Before replacing any FRU, read the entire page on removing and replacing FRUs.
• When you replace FRUs, it is recommended to use new nylon-coated screws.
• Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer
that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs
might be overwritten.
• Replace a FRU only with another FRU of the correct model. When you replace a FRU, make sure that the model
of the machine and the FRU part number are correct by referring to the FRU parts list.
• A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for a
variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge,
or software errors. Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective,
clear the error log and run the test again. If the error does not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.

What to do first
When you do return a FRU, you must include the following information in the parts exchange form or
parts return form that you attach to it:
1. Name and phone number of service technician
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Procedure index and page number in which the failing FRU was detected
6. Failing FRU name and part number
7. Machine type, model number, and serial number
8. Customer's name and address

Note: During the warranty period, the customer may be responsible for repair costs if the computer damage
was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper
maintenance by the customer. Following is a list of some common items that are not covered under warranty
and some symptoms that might indicate that the system was subjected to stress beyond normal use.

Before checking problems with the computer, determine whether the damage is covered under the warranty
by referring to the following list:

The following are not covered under warranty:

• LCD panel cracked from the application of excessive force or from being dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of an incompatible card
• Improper disc insertion or use of an optical drive

© Copyright Lenovo 2012 29

• Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive,
or the insertion of a diskette with multiple labels
• Damaged or bent diskette eject button
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect ac power adapter on laptop products

The following symptoms might indicate damage caused by nonwarranted activities:

• Missing parts might be a symptom of unauthorized service or modification.
• If the spindle of a hard disk drive becomes noisy, it may have been subjected to excessive force,
or dropped.

Power system checkout

To verify a symptom, do the following:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the ac power adapter.
4. Check that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the ac power adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you turn on the computer.

If you suspect a power problem, see the appropriate one of the following power supply checkouts:
• “Checking the ac power adapter” on page 30
• “Checking operational charging” on page 31
• “Checking the battery pack” on page 31

Checking the ac power adapter

You are here because the computer fails only when the ac power adapter is used.
• If the power-on indicator does not turn on, check the power cord of the ac power adapter for correct
continuity and installation.
• If the computer does not charge during operation, go to “Checking operational charging” on page 31

To check the ac power adapter, do the following:

1. Unplug the ac power adapter cable from the computer.
2. Measure the output voltage at the plug of the ac power adapter cable. See the following figure:

Pin Voltage (V dc)

1 +20
3 2 0
2
1
(20V)

Note: Output voltage of pin no.2 of the ac power adapter may different from the one you are servicing.
3. If the voltage is not correct, replace the ac power adapter.
4. If the voltage is acceptable, do the following:
• Replace the system board.
• If the problem persists, go to Chapter 5 “Lenovo B580” on page 37.

30 Hardware Maintenance Manual

Note: Noise from the ac power adapter does not always indicate a defect.

Checking operational charging

To check whether the battery charges properly during operation, use a discharged battery pack or a battery
pack that has less than 50% of the total power remaining when installed in the computer.

Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery
pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does
not turn on, replace the battery pack.

If the charge indicator still does not turn on, replace the system board. Then reinstall the battery pack. If it is
still not charged, go to the next section.

Checking the battery pack

Battery charging does not start until the power meter shows that less than 95% of the total power remains;
under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from
being overcharged or from having a shortened life.

To check your battery, move your cursor to the power meter icon in the icon tray of the Windows taskbar and
wait for a moment (but do not click it), and the percentage of battery power remaining is displayed. To get
detailed information about the battery, double-click the power meter icon.

Note: If the battery pack becomes hot, it may not be able to be charged. Remove it from the computer and
leave it at room temperature for a while. After it cools down, reinstall and recharge it.

To check the battery pack, do the following:

1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1 (+) and 7 (-). See the
following figure:

Terminal Voltage (V dc)

1 + 0 to + 14
7 Ground (-)

7(-)
6(-)
5
3 4
2(+)
1(+)
3. If the voltage is less than +11.0 V dc, the battery pack has been discharged.

Note: Recharging will take at least 3 hours, even if the indicator does not turn on.
If the voltage is still less than +11.0 V dc after recharging, replace the battery.
4. If the voltage is more than +11.0 V dc, measure the resistance between battery terminals 5 and 7.
The resistance must be 4 to 30 K Ω.
If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system
board.

Chapter 3. General checkout 31

32 Hardware Maintenance Manual
Chapter 4. Related service information
This chapter presents the following information:
• “Recovering the computer settings” on page 33
• “Passwords” on page 33
• “Power management” on page 34

Recovering the computer settings

Performing backup and recovery operations using the OneKey Recovery Pro program
The OneKey Recovery Pro program enables you to back up all your hard disk drive contents including the
operating system, data files, software programs, and personal settings. You can designate where the
OneKey Recovery Pro program stores the backup. After you have backed up the contents on the hard disk
drive, you can restore the complete contents of the hard disk drive, restore only the selected files, or restore
only the Windows operating system and applications.

Restoring factory contents using the Product Recovery program

On the Windows 7 operating system, you can use recovery media to restore the computer settings to the
factory contents only.

Attention: When you use the Product Recovery program to restore the computer settings, all the data you
have stored on the hard disk drive will be deleted and the computer settings will be restored to the factory
contents. During the restoring process, you will be given the option to save one or more files currently on the
hard disk drive to other media before the data is deleted.

Passwords
As many as two passwords might be needed for a Lenovo notebook computer: the power-on password, the
hard disk password, and the supervisor password.

If any of these passwords has been set, a prompt for it will be displayed on the screen whenever the
computer is turned on. The computer does not start until the password is entered.

Note: If only a supervisor password is set, the password prompt will not be displayed when the operating
system is started.

Power-on password
A power-on password (POP) protects the system from being powered on by an unauthorized person. The
password must be entered before an operating system can be booted.

Supervisor password
A supervisor password (SVP) protects the system information stored in the BIOS. The user must enter the
SVP in order to get access to the BIOS and change the system configuration.

Attention: If the SVP has been forgotten and cannot be made available to the service technician, there is no
service procedure to reset the password. The system board must be replaced for a scheduled fee.

© Copyright Lenovo 2012 33

Power management
Note: Power management modes are not supported for APM operating system.

To reduce power consumption, the computer has three power management modes: screen blank, sleep,
and hibernation.

Screen blank mode

If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off.
You also can turn off the LCD backlight by pressing Fn+F2.

To end screen blank mode and resume normal operation, press any key.

Sleep mode
When the computer enters sleep mode, the following events occur in addition to what occurs in screen
blank mode:
• The LCD is powered off.
• The hard disk drive is powered off.
• The CPU stops.

To enter sleep mode, press Fn+F1.

In certain circumstances, the computer goes into sleep mode automatically:

• If a “suspend time” has been set on the timer, and the user does not do any operation with the keyboard,
the hard disk drive, the parallel connector, or the diskette drive within that time.
• If the battery indicator blinks orange, indicating that the battery power is low.

To cause the computer to return from sleep mode and resume the operation, do one of the following:
• Press the Fn key.
• Open the LCD cover.
• Turn on the power button.

Also, when the time set on the resume timer elapses, the computer automatically returns from sleep mode
and resumes operation.

Note: The computer does not accept any input immediately after it enters sleep mode. Wait a few seconds
before taking any action to reenter operation mode.

Hibernation mode
In hibernation mode, the following occurs:
• The system status, RAM, VRAM, and setup data are stored on the hard disk drive.
• The system is powered off.

If you have defined one of the following actions as the event that causes the system to go into hibernation
mode, perform that action.
• Closing the lid.
• Pressing the power button.

Also, the computer goes into hibernation mode automatically in either of the following conditions:

34 Hardware Maintenance Manual

• If a “hibernation time” has been set on the timer, and if the user does not do any operation with the
keyboard, the hard disk drive, the parallel connector, or the diskette drive within that time.
• If the timer conditions are satisfied in suspend mode.

When the power is turned on, the computer returns from hibernation mode and resumes operation. The
hibernation file in the boot record on the hard disk drive is read, and system status is restored from the
hard disk drive.

Chapter 4. Related service information 35

36 Hardware Maintenance Manual
Chapter 5. Lenovo B580
This chapter presents the following product-specific service references and parts information:
• “Specifications” on page 37
• “Status indicators” on page 38
• “Fn key combinations” on page 39

Specifications
This topic lists the physical features for the Lenovo B580 models.

Processor
• See the system properties of your computer. You can do this as follows: Click Start, right-click
Computer; then from the pull down menu select Properties.

Memory
• Double data rate 3 (DDR3) synchronous dynamic random access memory (SDRAM)

Storage device
• 2.5-inch (7 mm height or 9.5 mm height) hard disk drive
• mSATA solid state drive

Display
• Size: 15.6 inches (396 mm)
• Resolution:
– LCD: 1366-by-768
– External monitor: Maximum 2048-by-1536
• Integrated camera

Keyboard
• 6-row Lenovo keyboard
• One-key Recovery Pro program button

Interface
• Combo audio jack (stereo headphone or headset)
• Two USB 2.0 connectors
• Two USB 3.0 connectors
• RJ45 Ethernet connector
• HDMI port
• External monitor connector
• 4-in-1 digital media card reader slot

Optical drive

© Copyright Lenovo 2012 37

• 12.7 mm Rambo optical drive

Wireless features
• Integrated wireless LAN
• Integrated Bluetooth (on some models)
• Integrated WiMAX
• 100/1000 Mbps Ethernet communication

Security features
• Fingerprint reader

Status indicators
This chapter presents the system status indicators that show the status of the computer.

1 2 3

Table 1. Status indicators

Indicator Meaning
1 Caps lock White: Caps Lock mode is enabled. You can enter all alphabetic characters (A-Z) in
uppercase without pressing the Shift key. To enable or disable Caps Lock mode, press
the caps lock key (CapsLk).
2 Numeric lock White: The separate numeric keypad on the keyboard is enabled. To enable or disable
the numeric keypad, press the numeric lock key (NmLk).

38 Hardware Maintenance Manual

Table 1. Status indicators (continued)
Indicator Meaning
3 Drive in use White: Data is being read from or written to the hard disk drive. When this indicator is
on, do not put the computer into sleep mode or turn off the computer.

Note: Do not move the system while the white drive-in-use light is on. Sudden physical
shock could cause drive errors.
4 Power and battery • Green: The battery charge level is between 80% and 100%, or the battery discharge
status indicator level is between 20% and 100%.
• Slow blinking green: The battery charge level is between 20% and 80%, and
charging is continuing. When the battery charge level reaches 80%, the battery status
indicator stops blinking, but the charging might continue until the battery is 100%
charged.
• Slow blinking orange: The battery charge level is between 5% and 20%, and the
charging is continuing. When the battery charge level reaches 20%, the blinking
color changes to green.
• Orange: The battery discharge level is between 5% and 20%.
• Fast blinking orange: The battery charge or discharge level is 5% or less.
• Off: The battery is detached or the computer is powered off.

Fn key combinations
The following table shows the function of each combination of Fn with a function key.

Table 2. Function key combinations

Key combination Description
Fn+Esc Turn on or turn off the integrated camera.
Fn+F1 Enter sleep mode.
Fn+F2 Enable or disable the backlight feature of the computer screen.
Fn+F3 Switch between the computer display and an external monitor.
Fn+F5 Enable or disable the built-in wireless features.
Fn+F6 Enable or disable the click pad.
Fn+F9 Start or pause playback of Windows Media Player.
Fn+F10 Stop playback of Windows Media Player.
Fn+F11 Skip to the previous track.
Fn+F12 Skip to the next track.
Fn+Insert Enable or disable the scroll lock function.
Fn+PrtSc Activate the system request.
Fn+Home Activate the pause function.
Fn+End Activate the break function.
Fn + up/down arrow Increase or decrease the display brightness level.
Fn + left/right arrow Increase or decrease the sound volume.

Chapter 5. Lenovo B580 39

40 Hardware Maintenance Manual
Chapter 6. FRU replacement notices
This chapter presents notices related to removing and replacing parts. Read this chapter carefully before
replacing any FRU.

Screw notices
Loose screws can cause a reliability problem. In the Lenovo notebook computer, this problem is addressed
with special nylon-coated screws that have the following characteristics:

• They maintain tight connections.

• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.

Do the following when you service this machine:

• Keep the screw kit in your tool bag.

• It is recommended to use new screws.
• It recommended to use each screw only once.
• Use a torque screwdriver if you have one.

Tighten screws as follows:

• Plastic to plastic
Turn an additional 90 degrees after the screw head touches the surface of the plastic part:

• Logic card to plastic

Turn an additional 180 degrees after the screw head touches the surface of the logic card:

• Torque driver
If you have a torque screwdriver, refer to the Torque column in the screw information table for each step.
• Make sure that you use the correct screw. It is recommended to use new screws for replacements. If
you have a torque screwdriver, tighten all screws firmly to the torque specified in the screw information
table for each step.
• Ensure torque screw drivers are calibrated correctly following country specifications.

© Copyright Lenovo 2012 41

42 Hardware Maintenance Manual
Chapter 7. Removing and replacing a FRU
This chapter provides instructions on how to remove or replace a FRU.

General guidelines
This chapter presents directions and drawings for use in removing and replacing a FRU. Be sure to observe
the following general rules:
1. Do not try to service any computer unless you have been trained and certified. An untrained person runs
the risk of damaging parts.
2. Before replacing any FRU, review Chapter 6 “FRU replacement notices” on page 41.
3. Begin by removing any FRUs that have to be removed before replacing the failing FRU. Such FRUs are
listed in each FRU replacement section. Remove them in the order in which they are listed.
4. Follow the correct sequence in the steps for removing a FRU, as given in the drawings by the numbers
in square callouts.
5. When turning a screw, turn it in the direction as given by the arrow in the drawing.
6. When removing a FRU, move it in the direction as given by the arrow in the drawing.
7. To put the new FRU in place, reverse the removal procedure and follow any notes that pertain to
replacement.
8. When replacing a FRU, use the correct screw(s) as shown in the procedures.

DANGER

Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets,
remove the battery pack, and then disconnect any interconnecting cables.

Attention: After replacing a FRU, do not turn on the computer until you have made sure that all screws,
springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking
the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical
short circuits.

Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before
touching it, establish personal grounding by touching a ground point with one hand or by using an
electrostatic discharge (ESD) strap (P/N 6405959).

1010 Battery pack

Removal steps of battery pack

DANGER

Use only the battery specified in the parts list for your computer. Any other battery could ignite
or explode.

© Copyright Lenovo 2012 43

Unlock the spring-loaded battery latch 1 . Holding the manual battery latch in the unlocked position, remove
the battery pack in the direction shown by the arrow 2 .

1
2

When installing: Install the battery pack in the slot. Make sure that the battery latches are in the locked
position.

1020 Bottom slot cover

For access, remove this FRU:
• “1010 Battery pack” on page 43

Removal steps of bottom slot cover

Remove the screws 1 , and then remove the cover 2 .

Step Screw (quantity) Color Torque

1 M2 × 3 mm, flat-head, nylon-coated (2) Black 1.85 kgfcm

1030 Optical drive

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44

44 Hardware Maintenance Manual

Removal steps of optical drive
Remove the screw 1 .

Step Screw (quantity) Color Torque

1 M2 × 3 mm, flat-head, nylon-coated (1) Black 1.85 kgfcm

Insert a screwdriver into the screw hole 2 and push the optical drive in the direction shown by the arrow 3 .
Then remove the optical drive.

3
2

Removal steps of optical drive bezel and optical drive bracket

Chapter 7. Removing and replacing a FRU 45

Remove the screws 1 and then remove the optical drive bracket.

2 1

Step Screw (quantity) Color Torque

1 M2 × 3 mm, flat-head, nylon-coated (2) Black 1.85 kgfcm

1040 Memory modules

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44

Removal steps of memory modules

Release the two latches on both edges of the socket at the same time in the direction shown by the arrows
1 , and then unplug the memory module in the direction shown by the arrow 2 .

1
1

46 Hardware Maintenance Manual

Note: If only one memory module is used on the computer you are servicing, the card must be installed in
SLOT-0 ( a : lower slot), but not in SLOT-1 ( b : upper slot).

When installing: Insert the notched end of the memory module into the socket. Press the memory module
firmly, and pivot it until it snaps into place. Make sure that it is firmly installed in the slot and does not
move easily.

1050 Hard disk drive assembly

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44

Attention:
• Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper
handling can cause damage and permanent loss of data.
• Before removing the drive, have the user make a backup copy of all the information on it if possible.
• Never remove the drive while the computer is operating or is in suspend mode.

Chapter 7. Removing and replacing a FRU 47

Removal steps of hard disk drive assembly
Remove the screw 1 , then pull the tab in the direction shown by the arrow 2 .

Step Screw (quantity) Color Torque

1 M2 × 3 mm, flat-head, nylon-coated (1) Black 1.85 kgfcm

Remove the hard disk drive from the slot 3 .

When installing: Make sure that the hard disk drive connector is attached firmly.

48 Hardware Maintenance Manual

Removal steps of hard disk drive bracket
Remove the screws 1 .

Step Screw (quantity) Color Torque

1 M3 × 4 mm, flat-head, nylon-coated (4) Silver 4 kgfcm

Remove the hard disk drive bracket as shown by the arrow 2 .

1060 PCI Express Mini Card for wireless LAN

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44

Chapter 7. Removing and replacing a FRU 49

Removal steps of PCI Express Mini Card for wireless LAN
In steps 1 , disconnect the cables from the card using the removal tool antenna RF connector (P/N: 08K7159)
or pick up the cables with your fingers and then gently disconnecting the cable from the card in the direction
of the arrows. Then remove the screw 2 .

2
1

Step Screw (quantity) Color Torque

2 M2 × 3 mm, flat-head, nylon-coated (1) Black 1.85 kgfcm

Remove the card in the direction shown by the arrow 3 .

When installing: Plug the black cable (MAIN) into the jack labeled M, and the white cable (AUX) into the jack
labeled A on the card.

50 Hardware Maintenance Manual

1070 mSATA solid state drive
For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44

Attention:
• Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper
handling can cause damage and permanent loss of data.
• Before removing the drive, have the user make a backup copy of all the information on it if possible.
• Never remove the drive while the computer is operating or is in suspend mode.

Removal steps of mSATA solid state drive

Remove the screw 1 .

Step Screw (quantity) Color Torque

1 M2 × 3 mm, flat-head, nylon-coated (1) Black 1.85 kgfcm

Chapter 7. Removing and replacing a FRU 51

Remove the mSATA solid state drive 2 .

1080 Backup battery

Removal steps of backup battery

DANGER

Use only the battery specified in the parts list for your computer. Any other battery could ignite
or explode.

Insert a screwdriver into the backup battery hole and push the backup battery until the battery pops up.

When installing: Make sure that the connector is attached firmly.

52 Hardware Maintenance Manual

1090 Keyboard
For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44

Removal steps of keyboard

Remove the screws 1 .

When installing: Make sure that the screws have been fastened to secure the keyboard.

Step Screw (quantity) Color Torque

1 M2.5 × 8 mm, flat-head, nylon-coated (3) Black 4.0 kgfcm

Push hard in the direction shown by the arrows 2 to unlatch the front side of the keyboard.

Chapter 7. Removing and replacing a FRU 53

Remove the keyboard in the direction shown by the arrow 3 .

Carefully lift the keyboard until you can see how it’s connected. Hold the keyboard above the computer
4 , and then detach the keyboard connector 5 6 .

54 Hardware Maintenance Manual

 4

6
5

When installing: Make sure that the keyboard connector is attached firmly.

1100 Keyboard bezel

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1090 Keyboard” on page 53

Chapter 7. Removing and replacing a FRU 55

Removal steps of keyboard bezel
Remove the screws 1 and 2 that secure the keyboard bezel.

2 1
1
2
2

1 1

1
1

1 1

Step Screw (quantity) Color Torque

1 M2.5 × 8 mm, flat-head, nylon-coated (10) Black 4.0 kgfcm
2 M2 × 3 mm, flat-head, nylon-coated (3) Black 1.85 kgfcm

Remove the screws 3 .

3
3

Step Screw (quantity) Color Torque

3 M2 × 5 mm, flat-head, nylon-coated (3) Black 1.85 kgfcm

56 Hardware Maintenance Manual

Detach the connectors.

5
4
10

11

9 6

When installing: Make sure that all the connectors are attached firmly.

Remove the keyboard bezel.

12
12
12

13

12

12

12
12
12
12

Chapter 7. Removing and replacing a FRU 57

1110 Fingerprint board and LED board
For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55

Removal steps of fingerprint board

Remove the screw 1 and the fingerprint board bracket 2 . Then remove the fingerprint board 3 .

3
3

Step Screw (quantity) Color Torque

1 M2 × 3 mm, flat-head, nylon-coated (1) Silver 1.85 kgfcm

58 Hardware Maintenance Manual

Removal steps of LED board
Peel off the mylar tape 1 . Then remove the LED board 2 .

1120 Power board and touch pad bracket

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55

Chapter 7. Removing and replacing a FRU 59

Removal steps of power board
Remove the screw 1 and then remove the power board 2 .

1
2

Step Screw (quantity) Color Torque

1 M2 × 3 mm, flat-head, nylon-coated (1) Black 1.85 kgfcm

Removal steps of touch pad bracket

Remove the screw 1 and then remove the touch pad bracket 2 .

2 1

Step Screw (quantity) Color Torque

1 M2 × 3 mm, flat-head, nylon-coated (1) Black 1.85 kgfcm

1130 Microphone assembly

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55

Removal steps of microphone assembly

Detach the connector 1 , and then remove the microphone assembly in the direction shown by the arrow 2 .

60 Hardware Maintenance Manual

 2 1

When installing: Make sure that the connector is attached firmly to the system board.

1140 I/O board

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55

Chapter 7. Removing and replacing a FRU 61

Removal steps of I/O board
Remove the screws 1 , and then detach the cable 2 3 . Remove the I/O board 4 .

1 1

Step Screw (quantity) Color Torque

1 M2 × 5 mm, flat-head, nylon-coated (2) Black 1.85 kgfcm

When installing: Make sure that the cable is attached firmly to the system board.

1150 System board assembly and USB board

Important notices for handling the system board:

When handling the system board, bear the following in mind:

• Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
• Avoid rough handling of any kind.
• At every point in the process, be sure not to drop or stack the system board.
• If you put a system board down, be sure to put it only on a padded surface such as an ESD mat or a corrugated
conductive surface.

62 Hardware Maintenance Manual

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60

Removal steps of system board assembly

Remove the screws 1 , and then detach the connectors as shown in the following illustration.

2
3

4 5
1

1 6
7

10

Step Screw (quantity) Color Torque

1 M2 × 5 mm, flat-head, nylon-coated (2) Black 1.85 kgfcm

When installing: Make sure that all the connectors are attached firmly.

Chapter 7. Removing and replacing a FRU 63

Detach the DC-in cable 11 . Remove the system board in the direction shown by the arrow 12 .

11

12

Removal steps of USB board

Remove the screw 1 , and then detach the connectors as shown in the following illustration. Remove
the USB board 4 .

3
2

Step Screw (quantity) Color Torque

1 M2 × 5 mm, flat-head, nylon-coated (1) Black 1.85 kgfcm

64 Hardware Maintenance Manual

1160 DC-in connector
For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
• “1140 I/O board” on page 61
• “1150 System board assembly and USB board” on page 62

Removal steps of DC-in connector

Detach the connector 1 . Remove the screw 2 and the DC-in connector bracket 3 . Then remove the DC-in
connector in the direction shown by the arrow 4 .

3
1

Step Screw (quantity) Color Torque

2 M2 × 3 mm, flat-head, nylon-coated (1) Black 1.85 kgfcm

Chapter 7. Removing and replacing a FRU 65

1170 Thermal module
For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
• “1150 System board assembly and USB board” on page 62

Removal steps of thermal module

Detach the fan connector 1 .

When installing: Make sure that the connector is attached firmly.

66 Hardware Maintenance Manual

Loosen the screws 2 to 8 .

8
6

2
4
3

Note: Different models might have different numbers of screws.

Lift the fan assembly in the direction shown by the arrow 9 .

Note: Be careful not to damage the connector.

Chapter 7. Removing and replacing a FRU 67

When installing: Before you attach the thermal module to the computer, apply thermal grease, at an amount
of 0.2 grams, on the part marked a and b as shown in the following illustration. Either too much or too less
application of grease can cause a thermal problem due to imperfect contact with a component.

For models with a discrete thermal module

For models with an integrated thermal module

1180 CPU
For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid state drive” on page 51
• “1080 Backup battery” on page 52

68 Hardware Maintenance Manual

• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
• “1150 System board assembly and USB board” on page 62
• “1170 Thermal module” on page 66

Attention: The CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling.

Removal steps of CPU

Rotate the head of the screw in the direction shown by the arrow 1 to release the lock, then remove the
CPU 2 .

When installing: Place the CPU above the CPU socket a , and then rotate the head of the screw in the
direction shown by the arrow b to secure the CPU.

1190 LCD unit

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53

Chapter 7. Removing and replacing a FRU 69

• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
• “1140 I/O board” on page 61
• “1150 System board assembly and USB board” on page 62
• “1160 DC-in connector” on page 65

Removal steps of LCD unit

Release the antenna cables from the cable guides. Then remove the screws 1 .

1
1

Step Screw (quantity) Color Torque

1 M2.5 × 5 mm, flat-head, nylon-coated (4) Black 4 kgfcm

When installing:
• Route the antenna cables along the cable guides. As you route the cables, make sure that they are
not subjected to any tension. Tension could cause the cables to be damaged by the cable guides,
or a wire to be broken.
• Make sure that the LCD connector is attached firmly and make sure that you do not pinch the antenna
cables when you attach the LCD assembly. Route the LCD cable along the cable guides.

70 Hardware Maintenance Manual

Remove the LCD unit in the direction shown by the arrow 2 .

1200 Speaker assembly

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
• “1140 I/O board” on page 61
• “1150 System board assembly and USB board” on page 62
• “1160 DC-in connector” on page 65
• “1190 LCD unit” on page 69

Chapter 7. Removing and replacing a FRU 71

Removal steps of speaker assembly
Remove the screws 1 . Then remove the speaker assembly 2 .

1
2

1
1
2

Step Screw (quantity) Color Torque

1 M2.5 × 5.7 mm, flat-head, nylon-coated (4) Black 4.0 kgfcm

1210 Base cover

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 44
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
• “1140 I/O board” on page 61
• “1150 System board assembly and USB board” on page 62
• “1160 DC-in connector” on page 65
• “1190 LCD unit” on page 69
• “1200 Speaker assembly” on page 71

Applying labels to the base cover

The new base cover FRU is shipped with a kit containing labels of several kinds.

The following illustration shows the correct location of each label.

72 Hardware Maintenance Manual

 12

1
11

10
2

6
7

If the Windows Certificate of Authentication label (COA) 11 is attached to a part that is replaced, return the
old part with the label attached to the customer, or provide a letter to the customer stating what the label
was originally on the system and what the label part number, serial number, and product key were.

The following labels need to be peeled off from the old base cover, and need to be put on the new base cover.

1 WWAN IMEI barcode label 7 Brazil WLAN label / WLAN label for US/CA/TW

2 PRC label / KCC label / MAC label 8 PPT label

3 Indonesia D side label 9 Malaysia SIRIM label

4 Indonesia WLAN and BT label 10 Vodafone label

5 Israel label 12 Rating label

6 Brazil Bluetooth label / Bluetooth label for US/CA/TW

2010 LCD front bezel

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1190 LCD unit” on page 69

Chapter 7. Removing and replacing a FRU 73

Removal steps of LCD front bezel
Remove the screws 1 .

Step Screw (quantity) Color Torque

1 M2 × 3.5 mm, flat-head, nylon-coated (2) Black 1.85 kgfcm

Remove the LCD front bezel in the direction shown by the arrows 2 .

2
2

When installing: Make sure that all the latches are attached firmly. Then secure the bezel with the screws.

2020 Integrated camera

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1190 LCD unit” on page 69
• “2010 LCD front bezel” on page 73

74 Hardware Maintenance Manual

Removal steps of integrated camera
Remove the integrated camera from the LCD cover as shown in the following illustration.

Note: The integrated camera is stuck on the top center of the LCD cover.

1
2

When installing: Stick the integrated camera to the top center of the LCD cover and adjust the placement to
make sure that the connector is attached firmly.

2030 LCD panel, LCD cable, and hinges

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1190 LCD unit” on page 69
• “2010 LCD front bezel” on page 73

Chapter 7. Removing and replacing a FRU 75

Removal steps of LCD panel and LCD cable
Remove the screws 1 . Then remove the LCD panel in the direction shown by the arrow 2 .

1 1

1 1

Step Screw (quantity) Color Torque

1 M2 × 3.5 mm, flat-head, nylon-coated (6) Black 1.85 kgfcm

Turn over the LCD panel 3 . Remove the LCD cable.

3
4

When installing: Make sure that the connector is attached firmly.

76 Hardware Maintenance Manual

Removal steps of hinges
Remove the screws 1 . Then remove the hinges 2 .

1
2

Step Screw (quantity) Color Torque

1 M2 × 3.5 mm, flat-head, nylon-coated (4) Black 1.85 kgfcm

2040 Antenna assembly and LCD rear cover

For access, remove these FRUs in order:
• “1010 Battery pack” on page 43
• “1190 LCD unit” on page 69
• “2010 LCD front bezel” on page 73
• “2020 Integrated camera” on page 74
• “2030 LCD panel, LCD cable, and hinges” on page 75

Chapter 7. Removing and replacing a FRU 77

Removal steps of antenna assembly and LCD rear cover
Release the antenna cables from the cable guides of the LCD rear cover assembly and from the hinges in
the direction shown by the arrows 1 .

Cable routing: Route the antenna cables along the cable guides and secure the antenna boards with
adhesive tapes. As you route the cables, make sure that they are not subjected to any tension. Tension
could cause the cables to be damaged by the cable guides, or a wire to be broken.

78 Hardware Maintenance Manual

Chapter 8. Locations
This chapter presents the locations of the Lenovo B580 hardware components.

Front and right-side view

17

16

15

14

13
5
12
6

7
8
11 9
10

Figure 1. Lenovo B580 front and right-side view

1 Integrated camera (on some models) 10 Combo audio jack

2 Wireless module antennas 11 Media card reader slot

3 Status indicators1 12 Touch pad

4 Speaker (right) 13 Microphone

5 ac power connector 14 Power and battery indicator1

6 USB connector 15 Power button

7 Optical drive 16 OneKey Recovery Pro program button

8 Fingerprint reader (on some models) 17 Speaker (left)

9 USB connector

1: For the description of the indicators, see “Status indicators” on page 38.

© Copyright Lenovo 2012 79

Bottom and left-side view

1
2
3

4
10 5
6
7
8
9

Figure 2. Lenovo B580 bottom and left-side view

1 Battery latch (manual) 6 Monitor connector

2 Battery pack 7 Ethernet connector

3 Battery latch (spring loaded) 8 HDMI port

4 Security keyhole 9 USB 3.0 connectors

5 Fan louvers 10 Bottom slot cover1

1: The memory modules, hard disk drive, and wireless cards are located underneath the bottom slot cover.

80 Hardware Maintenance Manual

Chapter 9. Parts list
This chapter contains following lists of the service parts.
• “Overall” on page 82
• “LCD FRUs” on page 85
• “Keyboard” on page 86
• “Miscellaneous parts” on page 88
• “ac power adapters” on page 89
• “Power cords” on page 90

Note: Each FRU is available for all types or models, unless specific types or models are specified.

© Copyright Lenovo 2012 81

Overall

23
2

a
j

3
22
4

21
b

20 5

c
d

19 6

7
18
8
17
e
16
9

10
15
f

h 11
g
14
12

13

Table 3. Parts list—Overall

No. FRU (Overall) FRU no.
1 LCD unit (see “LCD FRUs” on page 85.)
2 LB58 Power Board 90000235
3 LB58 LED Board W/Cable 90200814

82 Hardware Maintenance Manual

Table 3. Parts list—Overall (continued)
No. FRU (Overall) FRU no.
4 LB58 Upper Case W/TP 90200819
5 LB58 FingerPrint Board 90000236
6 LB58 USB Board 90000233
7 LB58 Speaker R 90200832
8 Battery, 6CELL 2.2Ah，Sanyo 2.2Ah 48Wh 6cell battey 121500047
8 Battery, 6CELL 2.2Ah, LG 2.2Ah 48Wh 6cell battey 121500049
8 Battery, 6CELL 2.2Ah, SMP 2.2Ah 48Wh 6cell battey 121500050
8 Battery, 6CELL 2.8Ah, SA L11S6F01 3S2P 62Wh Batt C01 Origa 121500051
8 Battery, 6CELL 2.8Ah, LG L11L6F01 3S2P 62Wh Batt C01 Origa 121500052
8 Battery, 6CELL 2.8Ah, SM/S L11M6F01 3S2P 62Wh Batt C01 Origa 121500053
9 LB58 DC-IN Cable 90200811
10 LB58 Lower Case 90200822
11 ODD, 12.7mm Tray-in Rambo, PLDS, DS-8A8SH 25201487
11 ODD, 12.7mm Tray-in Rambo, Sony Optiarc, AD-7740H 25201106
11 ODD, 12.7mm Tray-in Rambo, TSST, SN-208AB 25201108
11 ODD, 12.7mm Tray-in Rambo, HLDS, GT50N 25201635
12 LB58 IO Board 90000234
13 LB58 Memory Door 90200816
14 HDD, 320G 5400rpm, Toshiba Capricorn BS (H6sp)，Toshiba MK3265GSX 5400RPM 320G 16200097
14 HDD, 320G 5400rpm, HGST Jaquar B7, HGST HTS545032A7E380 5400PRM7mm 320G 16200068
14 HDD, 320G 5400rpm, Seagate Sapta 15, Seagate ST320LT020 5400RPM 7MM 320G 16005211
14 HDD, 500G 5400rpm, WD ML500M, WD5000BPVT-08A1Y 16200118
14 HDD, 500G 5400rpm, WD ML375M, WD5000BPVT-08HXZ 16200090
14 HDD, 500G 5400rpm, Toshiba Capricorn BS (H6sp), Toshiba MK5065GSX 5400RPM 500G 16200098
14 HDD, 750G 5400rpm, WD ML500M, WD7500BPVT-08A1Y 16200119
14 HDD, 750G 5400rpm, WD ML375M, WD7500BPVT-08HXZ 16200121
14 HDD, 750G 5400rpm, HGST Jaguar B, HTS541075A9E680 16200192
14 HDD, 1TB 5400rpm, WD ML500M, WD10JPVT-08A1Y 16200120
14 HDD, 1TB 5400rpm, HGST Jaquar B, HTS541010A9E680 16200193
14 HDD, 320G 7200rpm, WD MX320S-1, WD3200BEKT-08PVM 16200092
14 HDD, 320G 7200rpm, Toshiba Capricorn CS (H6sp), TSB MK3261GSY 7200PRM 9.5mm 320G HDD 16200099
14 HDD, 320G 7200rpm, HGST Jaquar C7, HTS725032A7E630 16200194
14 HDD, 320G 7200rpm, Seagate Julius 1 4K, Seagate ST320LT007 7200RPM 7MM 320G 16005030
14 HDD, 500G 7200rpm, WD MX375M, WD5000BPKT-08PK4T 16200124
14 HDD, 500G 7200rpm, Toshiba Capricorn CS (H6sp), TSB MK5061GSY 7200PRM 9.5mm 500G HDD 16200100
14 HDD, 500G 7200rpm, Jaguar C7, HTS725050A7E630 16200195
15 LB58 Microphone 90200829
16 LB58 Speaker L 90200833

Chapter 9. Parts list 83

Table 3. Parts list—Overall (continued)
No. FRU (Overall) FRU no.
17 SSD, mSATA 16G, Sandisk, U100 mSATA SDSA5DK-016G 16200215
18 WLAN, Non-Intel 1x1 11bgn + BT4.0 Combo, Broadcom 4313 + 20702 20200100
20200101
18 WLAN, Non-Intel 2x2 11abgn + BT4.0 Combo, Broadcom 43228 + 20702 20200098
20200099
18 WLAN, Intel 2x2 11bgn + BT4.0 Combo, Jackson Peak 1 20200078
18 WLAN, Non-Intel 1x1 11bgn, Broadcom BCM4313 1*1 BGN MOW 20200102
18 WLAN, Non-Intel 1x1 11bgn, Realtek bgn 1x1 HMC WLAN Stockton 20200016
19 RAM, DDRIII 1600 2GB, Samsung, M471B5773DH0-CK0 DDR3 1600 2GB 11200340
19 RAM, DDRIII 1600 2GB, Hynix, HMT325S6CFR8C-PB DDR3 1600 2GB 11200343
19 RAM, DDRIII 1600 2GB, Micron, MT8KTF25664HZ-1G6M1 DDR3 1600 2GB 11200346
19 RAM, DDRIII 1600 2GB, Ramaxel, RMT3150ED58E8W-1600 DDR3 1600 2GB 11200392
19 RAM, DDRIII 1600 2GB, Sharetronic(Micron), SM321NH08IAF DDR3 1600 2GB 11200396
19 RAM, DDRIII 1600 4GB, Samsung, M471B5273DH0-CK0 DDR3 1600 4GB 11200341
19 RAM, DDRIII 1600 4GB, Hynix, HMT351S6CFR8C-PB DDR3 1600 4GB 11200344
19 RAM, DDRIII 1600 4GB, Micron, MT16KTF51264HZ-1G6M1 DDR3 1600 4GB 11200347
19 RAM, DDRIII 1600 4GB, Ramaxel, RMT3160ED58E9W-1600 DDR3 1600 4GB 11200393
19 RAM, DDRIII 1600 4GB, Sharetronic(Micron), SM322NQ08IAF DDR3 1600 4GB 11200397
20 LB58 MB UMA W/HDMI WO/3G 90000239
20 LB58 MB DIS N13P-GE 1G W/HDMI WO/3G 90000240
21 CPU, Intel I5-2520M 2.5G 3M 2c J1 PGA processor 102001067
21 CPU, Intel B815 1.6G Q0 2M 2cPGA processor 102500229
21 CPU, Intel I3-2370M 2.4G J1 3M 2cPGA processor 102500228
21 CPU, Intel SNB I3-2350M 2.3G 3M J1 PGA processor 102500018
21 CPU, Intel SNB I3-2330M 2.2G 3M J1 PGA processor 102500017
21 CPU, Intel SNB B950 2.1G 2M Q0 PGA processor 102500016
21 CPU, Intel SNB B940 2.0G 2M Q0 PGA processor 102500015
21 CPU, Intel SNB I3-2310M 2.1G 3M 2c J1 PGA processor 102001065
21 CPU, Intel B970 2.3G D2 2M 2cPGA processor 102500230
21 CPU, Intel SNB B800 1.5G Q0 2M 2c PGA processor 102500101
21 CPU, Intel SNB B960 2.2G 2M 35W PGA processor 102500133
21 CPU, Intel B820 1.7G Q0 2M 2cPGA processor 102500350
21 CPU, Intel I3-2308M 2.1G Q0 3M 2cPGA processor 102500351
21 CPU, i5-3210M Ivy Bridge L-0 3MB 2c PGA 2.5GHz STD 35W processor 102500301
21 CPU, i3-3110M Ivy Bridge L-0 3MB 2c PGA 2.3GHz STD 35W processor 102500303
22 LB58 Thermal Module UMA W/FAN 90200827
22 LB58 Thermal Module DIS W/FAN 90200828
23 Keyboard (see “Keyboard” on page 86.)
— ac power adapter (see “ac power adapters” on page 89.)

84 Hardware Maintenance Manual

LCD FRUs
In Lenovo B580 models, the type of LCD is 15.6-inch high definition (HD) TFT LCD (Table 4 “Parts list -
LCD” on page 85).

3
k

Table 4. Parts list - LCD

No. FRU FRU no.
1 LB58 LCD Bezel 90200824
2 LB58 Hinge L+R 90200817
3 LB58 Antenna R 90200826
4 LB58 Camera 0.3M 90000238
5 LB58 LCD Cover 90200823
6 LB58 Antenna L 90200825
7 Panel, 15.6 HD Wedge Glossy, SEC, LTN156AT24-L01 18200114
7 Panel, 15.6 HD Wedge Glossy, LGD, LP156WH4-TLN1 18200158
7 Panel, 15.6 HD Wedge Glossy, AUO, B156XTN02.0 18200157

Chapter 9. Parts list 85

Table 4. Parts list - LCD (continued)
No. FRU FRU no.
7 Panel, 15.6 HD Wedge Anti-Glare, AUO, B156XTN02.1 18200649
7 Panel, 15.6 HD Wedge Anti-Glare, SEC, LTN156AT24-401 18200650
7 Panel, 15.6 HD Wedge Anti-Glare, CMI, N156BGE-L11 18200651
7 Panel, 15.6 HD Wedge Anti-Glare, LGD, LP156WH4-TLP1 18200652

Keyboard
Table 5. Parts list - Keyboard (Dafon)
Language FRU no.
Arabic 25204626
Belgian 25204634
Brazilian Portuguese 25204627
Bulgarian 25204640
French, English 25204620
Czech, Slovak 25204639
C& Nordics 25204633
Dutch 25204629
French 25204624
German 25204625
Greek 25204630
Hebrew 25204631
Hungarian 25204632
Icelandic 25204635
Indian 25204641
Italian 25204614
Korean 25204621
Latin 25204619
Portuguese 25204618
Russian 25204623
Slovenian 25204636
Swiss 25204637
Spanish 25204615
Thai 25204617
Traditional Chinese 25204622
Turkish 25204616
U.K. English 25204613
U.S. English 25204612
U.S. English (International, with a Euro symbol) 25204638

86 Hardware Maintenance Manual

Table 6. Parts list - Keyboard (Sunrex)
Language FRU no.
Arabic 25204656
Belgian 25204664
Brazilian Portuguese 25204657
Bulgarian 25204670
Czech, Slovak 25204669
C& Nordics 25204663
Dutch 25204659
French 25204654
French, English 25204650
German 25204655
Greek 25204660
Hebrew 25204661
Hungarian 25204662
Icelandic 25204665
Indian 25204671
Italian 25204644
Japanese 25204658
Korean 25204651
Latin 25204649
Portuguese 25204648
Russian 25204653
Swiss 25204667
Spanish 25204645
Slovenian 25204666
Thai 25204647
Traditional Chinese 25204652
Turkish 25204646
U.K. English 25204643
U.S. English 25204642
U.S. English (International, with a Euro symbol) 25204668

Table 7. Parts list - Keyboard (Chicony)

Language FRU no.
Arabic 25204597
Belgian 25204604
Brazilian Portuguese 25204598
Bulgarian 25204610
Czech, Slovak 25204609

Chapter 9. Parts list 87

Table 7. Parts list - Keyboard (Chicony) (continued)
Language FRU no.
C& Nordics 25204603
Dutch 25204599
French 25204595
French, English 25204591
German 25204596
Greek 25204600
Hebrew 25204601
Hungarian 25204602
Indian 25204611
Icelandic 25204605
Italian 25204585
Japanese 25204584
Korean 25204592
Latin 25204590
Portuguese 25204589
Russian 25204594
Slovenian 25204606
Swiss 25204607
Spanish 25204586
Thai 25204588
Traditional Chinese 25204593
Turkish 25204587
U.K. English 25204583
U.S. English 25204582
U.S. English (International, with a Euro symbol) 25204608

Miscellaneous parts
Table 8. Parts list - Miscellaneous parts
FRU FRU no.
(a) LB58 Power Board Cable 90200809
(b) LB58 FP Board Cable 90200810
(c) LB58 FP Bracket 90200818
(d) LB58 USB Cable 90000237
(e) LB58 DC-IN Bracket 90200821
(f) LA48 ODD Bracket 33.4TD06.001 90200518
(g) LB58 ODD Bezel Rambo 90200815
(h) LA48 HDD Bracket 60.4TE08.001 90200520

88 Hardware Maintenance Manual

Table 8. Parts list - Miscellaneous parts (continued)
FRU FRU no.
(i) LB58 TP Bracket 90200820
(j) LB58 TP Cable 90200813
(k) LB58 LCD Cable 90200812
LB58 Microphone Rubber 90200830
LB58 LCD Bezel Screw Pad 90200831

Note: Italicized letters in parentheses are references to the exploded view in “Overall” on page 82.

ac power adapters
Table 9. Parts list—2-pin (65 W) ac power adapters
FRU FRU no.
Delta ADP-65AD AA, EuP model 36200090
Liteon PA-1650-75I, EuP model 36200092
Chicony Power A065R040L, EuP model 36200094
Delta ADP-65SB A, EPA model 36200143
Liteon PA-1650-53I, EPA model 36200144
Chicony Power A065R028L, EPA model 36200210

Table 10. Parts list—3-pin (65 W) ac power adapters

FRU FRU no.
Delta ADP-65AD BA, EuP model 36200096
Liteon PA-1650-76I, EuP model 36200097
Chicony Power A065R041L, EuP model 36200098
Delta ADP-65SB B, EPA model 36200033
Liteon PA-1650-54I, EPA model 36200034
Chicony Power A065R017L, EPA model 36200212

Table 11. Parts list—2-pin (90 W) ac power adapters

FRU FRU no.
Delta ADP-90SD AA, EuP model 36200102
Liteon PA-1900-75I, EuP model 36200101
Chicony Power A090A047L, EuP model 36200103
Delta PA-1900-53I, EPA model 36200147
Liteon ADP-90ZH CA, EPA model 36200149
Chicony Power HP-A0905A2C1LF, EPA model 36200150

Chapter 9. Parts list 89

Table 12. Parts list—3-pin (90 W) ac power adapters
FRU FRU no.
Delta ADP-90SD BA, EuP model 36200106
LITEON PA-1900-76I, EuP model 36200105
Chicony A090A048L, EuP model 36200107
Liteon PA-1900-54I, EPA model 36200030
Delta ADP-90ZH DA, EPA model 36200031
Chicony Power HP-BT090E13LF, EPA model 36200032

Power cords
A Lenovo power cord for a specific country or region is usually available only in that country or region.

Table 13. Parts list - 3-pin power cords (Linetek)

Country or region FRU no.
Argentina 145000599
• LINETEK LS15+H03VV-F+LP39 1 m
Australia, New Zealand 145000589
• LINETEK LS15+H03VV-F+LP-23A 1 m
Brazil 145000596
• LINETEK LS15 H03VV-F LP26A 1 m
CE 145000585
• LINETEK LP-34+H03VV-F + LS15 1 m
China 145000600
• LINETEK PC323+RVV300/300+LS15 1 m
Denmark 145000598
• LINETEK LS15+H03VV-F+LP-38 1 m
Indian 145000592
• LINETEK PE-361+ H05VV-F+ LS15 1 m
Israel 145000595
• LINETEK LS15+H03VV-F+LP-41 1 m
Italy 145000591
• LINETEK LS15+H03VV-F+PE-336 1 m
Japan 145000587
• LINETEK LS15+VCTF+LP-54 1 m
Korea 145000590
• LINETEK LS15+H05VV-F+LP-E04A 1 m
South Africa 145000586
• LINETEK LS15+H03VV-F+PE-364 1 m
Switzerland 145000597
• LINETEK LS15+H03VV-F+LP-37 1 m

90 Hardware Maintenance Manual

Table 13. Parts list - 3-pin power cords (Linetek) (continued)
Country or region FRU no.
Taiwan 145000588
• LINETEK LS15+VCTF+LP-53 1 m
U.K. 145000593
• LINETEK LP-61L+ H03VV-F+ LS15 1 m
UL 145000594
• LINETEK LP-30B + SPT-2 + LS15 1 m

Table 14. Parts list - 3-pin power cords (Longwell)

Country or region FRU no.
Argentina 145000567
• Longwell LP-24+H03VV-F+LS-18 1 m
Australia, New Zealand 145000557
• Longwell LP-23A+LFC-3R+LS-18 1 m
Brazil 145000564
• Longwell LP-46+H03VV-F+LS-18 1 m
CE 145000553
• Longwell LP-34A+H03VV-F+LS-18 1 m
China 145000568
• Longwell LSG-31+RVV300/300+LS-18 1 m
Denmark 145000566
• Longwell LP-40+H03VV-F+LS-18 1 m
Indian 145000560
• Longwell LP-67+BIS+LS-18 1 m
Israel 145000563
• Longwell LP-41+H03VV-F+LS-18 1 m
Italy 145000559
• Longwell LP-22+H03VV-F+LS-18 1 m
Japan 145000555
• Longwell LP-54+VCTF+LS-18 1 m
Korea 145000558
• Longwell LP-486+KTLH03VV-F+LS-5 1 m
South Africa 145000554
• Longwell LP-39+H03VV-F+LS-18 1
Switzerland 145000565
• Longwell LP-37+H03VV-F+LS-18 1 m
Taiwan 145000556
• Longwell LP-71+VCTF+LS-33 1 m

Chapter 9. Parts list 91

Table 14. Parts list - 3-pin power cords (Longwell) (continued)
Country or region FRU no.
U.K. 145000561
• Longwell LP-61L+H03VV-F+LS-18 1 m
UL 145000562
• Longwell LP-30B+SPT-2 18AWG+LS-18 1 m

Table 15. Parts list - 3-pin power cords (Volex)

Country or region FRU no.
Argentina 145000528
• VOLEX VA2073+H03VV-F+VAC5S 1 m
Australia, New Zealand 145000532
• VOLEX AU10S3+H03VV-F+VAC5S 1 m
Brazil 145000527
• VOLEX CH10S3+H03VV-F+VAC5S 1 m
CE 145000525
• VOLEX M2511+HO3VV-F+VAC5S 1 m
China 145000538
• VOLEX GB10S3+RVV 300/500+VAC5S 1 m
Denmark 145000534
• VOLEX MP233D+H03VV-F+VAC5S 1 m
Indian 145000536
• VOLEX IA6A3+IS694+VAC5S 1 m
Israel 145000526
• VOLEX SI16S3+H03VV-F+VAC5S 1 m
Italy 145000535
• VOLEX IT10S3+HO3VV-F+VAC5S 1 m
Japan 145000530
• VOLEX VAC5S+VCTF+M755 1 m
Korea 145000533
• VOLEX M2511+KETI IEC+VAC5S 1 m
South Africa 145000529
• VOLEX SA16A+HO3VV-F+VAC5S 1 m
Switzerland 145000524
• VOLEX MP232+H03VV-F+VAC5S 1 m
Taiwan 145000531
• VOLEX TW15CS3+VCTF+VAC5S 1 m
U.K. 145000605
• VOLEX MP5004+H03VV-F+VAC5S 1 m
UL 145000537
• Volex US15S3+SPT-2 ＋VAC5S 1 m

92 Hardware Maintenance Manual

Table 16. Parts list - 2-pin power cords (Linetek)
Country or region FRU no.
Africa 145500024
• LINETEK PE364("O")+H03VVH2-F+LS7H 1 m
Argentina 145500030
• LINETEK LP40+H03VVH2-F+LS7H 1 m
Australia 145500023
• LINETEK LP15A+H03VVH2-F+LS7 1 m
Brazil 145500028
• LINETEK LP25+H03VVH2-F+LS7H 1 m
CCC 145500018
• LINETEK PC205+RVV 0.75/2C+COC03 1 m
CE 145500022
• LINETEK LP21+H03VVH2-F+ LS7 1 m
India 145500020
• LINETEK LP28+IS:694 0.75/2C+ LS7H 1 m
Israel 145500029
• LINETEK LP45+H03VV-F+LS7 1 m
Japan 145500026
• LINETEK LP51A+HVCTFK 0.75/2C+LS7J 1 m
Korea 145500025
• LINETEK LPE03A+H03VVH2-F+LS7 1 m
Taiwan 145500027
• LINETEK LP51A+VCTFK 0.75/2C+LS7J 1 m
UL 145500021
• LINETEK LP5+SPT-2 #18/2C+ LS7C 1 m
UK 145500019
• LINETEK LP61L+H03VVH2-F+ LS7H 1 m

Chapter 9. Parts list 93

94 Hardware Maintenance Manual
Appendix A. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult
your local Lenovo representative for information on the products and services currently available in your
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's
responsibility to evaluate and verify the operation of any other product, program, or service.

Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing

LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow
disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply
to you.

This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.

The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in this
document does not affect or change Lenovo product specifications or warranties. Nothing in this document
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo
or third parties. All information contained in this document was obtained in specific environments and is
presented as an illustration. The result obtained in other operating environments may vary.

Lenovo may use or distribute any of the information you supply in any way it believes appropriate without
incurring any obligation to you.

Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of
the materials for this Lenovo product, and use of those Web sites is at your own risk.

Any performance data contained herein was determined in a controlled environment. Therefore, the result
obtained in other operating environments may vary significantly. Some measurements may have been
made on development-level systems and there is no guarantee that these measurements will be the same
on generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.

© Copyright Lenovo 2012 95

Electronic emissions notices
For electronic emission information on Class B digital devices, refer to the corresponding information in
the User Guide.

Trademarks
The following terms are trademarks of Lenovo in the United States, other countries or both:

Lenovo
OneKey

Windows is the trademark of the Microsoft group of companies.

Intel is the trademark of Intel Corporation or its subsidiaries in the United States, other countries, or both.

Other company, product, or service names may be the trademarks or service marks of others.

96 Hardware Maintenance Manual