ServiceMode 3.71 by stef_no1 e-mail: stef_no1@yahoo.

com
This is ServiceModeWare. If you find this usefull send me 2 new service modes.
Manufacturer Model Chassis Product Mode Enter
Simultaneous press + & - on local panel and
Akai CT-2119 CTV Test Mode
then power on with main switch. Exit: POWER.
OFF: Select programm 38. Simultaneous press
(3 sec) STORE & CONTROL+ on local keyboard.
Allstar 3750 CTV Hotel Mode ON: Select programm 38. Simultaneous press
(3 sec) STORE & PROGRAM- on local
keyboard.
Press UP & DOWN buttons together on tv's
Child Lock local control and then switch on. You will see
AudioTon CTV 5502 10.3 90° MONO CTV
Clear SERVICE MODE. Do not press any button,
just power off the set, then on.
Press UP & DOWN buttons together on tv's
AudioTon CTV 5502 10.3 90° MONO CTV Service Mode
local control and then switch on.
Simultaneous press P+ & P- on local panel and
Beko CTV Service Mode
then power on with main switch.
Press button P/C on RC and switch on TV with
Blaupunkt MM63-13VT FM240.00 CTV ATS
main switch.
Hotel Mode Press button 'i' on RC and switch on TV with
Blaupunkt MM63-13VT FM240.00 CTV
Cancel main switch.

Switch off TV with RC (st-by). Switch off TV with

main switch. Wait a few sec till ST_BY LED
Brandt ICC9 CTV Service Mode switch off. Simultaneous press VT button on RC
and switch on TV with main switch. Press VT
button again. (WARNING: scart must be free.)

Press and hold P+ and P- on local panel, then

Continental CT1412B CTV Service Mode
switch on TV with main switch.

Switch off TV with RC (st-by). Switch off TV with

main switch. Wait a few sec till ST_BY LED
Ferguson ICC9 CTV Service Mode switch off. Simultaneous press VT button on RC
and switch on TV with main switch. Press VT
button again. (WARNING: scart must be free.)

Put TV into standby, then turn power off, then

Hotel Mode turn power on whilst holding standby button on
Ferguson TX92 CTV
Cancel remote and step through menus to `vol set` and
increase level to max.
MUTE --> OK (M) --> TV
17/21B60
Finlux STEREO PLUS CTV Service Mode Controls: cursor buttons. Store: OK (M).
63/71Y2
Exit: TV
Simultaneously press MENU, VOL-, PR- on
GoldStar MC-51B CTV Service Mode
the local panel.
Turn on 'TV Internal Service Program' switch on
the digital modul (SE on display). On RC: 1=U1
BURGGRAF V SHIFT, 2=U2 V LIN DN, 3=U3 V LIN, 4=H1
Graetz STEREO 4876 DIGI III 110° CTV Service Mode H SHIFT, 5=H2 H AMP, 6=H3 EW AMP, 7=
Digivision C, 8=C1, 9=C2, 0=H4 EW TRAPEZ…
TV=MEMO, VOL+/-=ADJUST.

Child Lock
Grundig CUC1800 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Manufacturer Model Chassis Product Mode Enter
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1800 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Menu guide: 'i', 'Special functions', 'Service',
Grundig CUC1800 CTV Service Mode
'Code 8500'.
Press and hold button VOL+ on the TV and
Grundig CUC1805 CTV ATS Reset
switch the mains button ON. ATS bit is set.
Child Lock
Grundig CUC1805 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the button 'P-' on the RC while
Default
switching on with the mains button. (This is
Grundig CUC1805 CTV Values
only possible once on replacement of the NVM
Entering
or uP).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1805 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Press 'i'. Dialog Center --> Service --> 'for
Grundig CUC1805 CTV Service Mode
authorized dealer' --> Code Number 8500.
Volume
Press and hold the 'AUX' button on the RC while
Grundig CUC1805 CTV Offset
switching the TV on with the mains button.
Cancel
Child Lock
Grundig CUC1806 CTV General reset with number 7038.
Cancel
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1806 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1806 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1806 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1806 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1821 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1821 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Menu guide: 'i', 'Special functions', 'Service',
Grundig CUC1821 CTV Service Mode
'Code 8500'.
Child Lock
Grundig CUC1822 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1822 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Menu guide: 'i', 'Special functions', 'Service',
Grundig CUC1822 CTV Service Mode
'Code 8500'.
Child Lock
Grundig CUC1824 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Manufacturer Model Chassis Product Mode Enter
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1824 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Menu guide: 'i', 'Special functions', 'Service',
Grundig CUC1824 CTV Service Mode
'Code 8500'.
Press and hold button VOL+ on the TV and
Grundig CUC1825 CTV ATS Reset
switch the mains button ON. ATS bit is set.
Child Lock
Grundig CUC1825 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1825 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Press and hold the P- buton on the TV and
switch on with the mains button. Loading
ROM Data
Grundig CUC1825 CTV the Average Values / Emergency Data Set
Loading
(ROM Dana). This is only possible once on
replacement of the NVM or uP.
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1825 CTV Service Mode
for retailer', 'Code 8500'.
Volume
Press and hold the 'AUX' button on the RC while
Grundig CUC1825 CTV Offset
switching the TV on with the mains button.
Cancel
Press and hold button VOL+ on the TV and
Grundig CUC1826 CTV ATS Reset
switch the mains button ON. ATS bit is set.
Child Lock
Grundig CUC1826 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1826 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Press and hold the P- buton on the TV and
switch on with the mains button. Loading
ROM Data
Grundig CUC1826 CTV the Average Values / Emergency Data Set
Loading
(ROM Dana). This is only possible once on
replacement of the NVM or uP.
Press 'i'. Dialog Center --> Service --> 'for
Grundig CUC1826 CTV Service Mode
authorized dealer' --> Code Number 8500.
Volume
Press and hold the 'AUX' button on the RC while
Grundig CUC1826 CTV Offset
switching the TV on with the mains button.
Cancel
Child Lock
Grundig CUC1827 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the button 'P-' on the RC while
Default
switching on with the mains button. (This is
Grundig CUC1827 CTV Values
only possible once on replacement of the NVM
Entering
or uP).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1827 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1827 CTV Service Mode
for retailer', 'Code 8500'.
Volume
Press and hold the 'AUX' button on the RC while
Grundig CUC1827 CTV Offset
switching the TV on with the mains button.
Cancel
Child Lock
Grundig CUC1828 CTV General reset with number 7038.
Cancel
Manufacturer Model Chassis Product Mode Enter
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1828 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1828 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1828 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1828 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1829 CTV General reset with number 7038.
Cancel
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1829 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1829 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1829 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1829 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1830 CTV General reset with number 7038.
Cancel
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1830 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1830 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1830 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1830 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1836 CTV General reset with number 7038.
Cancel
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1836 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Manufacturer Model Chassis Product Mode Enter
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1836 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1836 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1836 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1842 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1842 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1842 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1842 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1842 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1851 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1851 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Menu guide: 'i', 'Special functions', 'Service',
Grundig CUC1851 CTV Service Mode
'Code 8500'.
Child Lock
Grundig CUC1852 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1852 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Menu guide: 'i', 'Special functions', 'Service',
Grundig CUC1852 CTV Service Mode
'Code 8500'.
Child Lock
Grundig CUC1881 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1881 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Menu guide: 'i', 'Special functions', 'Service',
Grundig CUC1881 CTV Service Mode
'Code 8500'.
Child Lock
Grundig CUC1892 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1892 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Menu guide: 'i', 'Special functions', 'Service',
Grundig CUC1892 CTV Service Mode
'Code 8500'.
Manufacturer Model Chassis Product Mode Enter
Child Lock
Grundig CUC1894 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1894 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1894 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1894 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1894 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1929 CTV General reset with number 7038.
Cancel
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1929 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1929 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1929 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1929 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1952 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1952 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1952 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1952 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1952 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1962 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Manufacturer Model Chassis Product Mode Enter
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1962 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1962 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1962 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1962 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1983 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1983 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1983 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1983 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1983 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC1984 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Demo on: Depress and hold button 'L+' on the
TV and switch the TV on with the mains button.
Press the 'P+' button within a time of 10s.
Grundig CUC1984 CTV Demo Mode
Demo off: ATS Reset (by depressing the 'L+'
button on the TV while switching on with the
mains button).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC1984 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Factory
Default
Grundig CUC1984 CTV Buttons 'AUX', 'OK'.
Values
Resetting
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC1984 CTV Service Mode
for retailer', 'Code 8500'.
Depress and hold button 'i' on the RC while
Band Limits switching on with the mains button. Move the
Grundig CUC2020 CTV
Cancelling bar to 'AGC' in the Service Menu and operate
the buttons 'AUX', 'OK' in this order.
Child Lock
Grundig CUC2020 CTV General reset with number 7038.
Cancel
Manufacturer Model Chassis Product Mode Enter

Depress and hold the button 'P-' on the RC while

switching on with the mains button.
Default
(Additionally on replacement of the memory, the
Grundig CUC2020 CTV Values
Hotel Mode and the band limits are to be
Entering
deactivated and the AGC and AFC are to be
readjusted).

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC2020 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'i' button on the RC while

OSD
Grundig CUC2020 CTV switching on with the mains button. Set the
position
OSD position in the menu and store with 'OK'.
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC2020 CTV Service Mode
for retailer', 'Code 8500'.
Depress and hold button 'i' on the RC while
Band Limits switching on with the mains button. Move the
Grundig CUC2030 CTV
Cancelling bar to 'AGC' in the Service Menu and operate
the buttons 'AUX', 'OK' in this order.
Child Lock
Grundig CUC2030 CTV General reset with number 7038.
Cancel

Depress and hold the button 'P-' on the RC while

switching on with the mains button.
Default
(Additionally on replacement of the memory, the
Grundig CUC2030 CTV Values
Hotel Mode and the band limits are to be
Entering
deactivated and the AGC and AFC are to be
readjusted).

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC2030 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'i' button on the RC while

OSD
Grundig CUC2030 CTV switching on with the mains button. Set the
position
OSD position in the menu and store with 'OK'.
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC2030 CTV Service Mode
for retailer', 'Code 8500'.
Depress and hold button 'i' on the RC while
Band Limits switching on with the mains button. Move the
Grundig CUC2031 CTV
Cancelling bar to 'AGC' in the Service Menu and operate
the buttons 'AUX', 'OK' in this order.
Child Lock
Grundig CUC2031 CTV General reset with number 7038.
Cancel

Depress and hold the button 'P-' on the RC while

switching on with the mains button.
Default
(Additionally on replacement of the memory, the
Grundig CUC2031 CTV Values
Hotel Mode and the band limits are to be
Entering
deactivated and the AGC and AFC are to be
readjusted).
Manufacturer Model Chassis Product Mode Enter

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC2031 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'i' button on the RC while

OSD
Grundig CUC2031 CTV switching on with the mains button. Set the
position
OSD position in the menu and store with 'OK'.
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC2031 CTV Service Mode
for retailer', 'Code 8500'.
Depress and hold button 'i' on the RC while
Band Limits switching on with the mains button. Move the
Grundig CUC2050 CTV
Cancelling bar to 'AGC' in the Service Menu and operate
the buttons 'AUX', 'OK' in this order.
Child Lock
Grundig CUC2050 CTV General reset with number 7038.
Cancel

Depress and hold the button 'P-' on the RC while

switching on with the mains button.
Default
(Additionally on replacement of the memory, the
Grundig CUC2050 CTV Values
Hotel Mode and the band limits are to be
Entering
deactivated and the AGC and AFC are to be
readjusted).

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC2050 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'i' button on the RC while

OSD
Grundig CUC2050 CTV switching on with the mains button. Set the
position
OSD position in the menu and store with 'OK'.
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC2050 CTV Service Mode
for retailer', 'Code 8500'.
Depress and hold button 'i' on the RC while
Band Limits switching on with the mains button. Move the
Grundig CUC2051 CTV
Cancelling bar to 'AGC' in the Service Menu and operate
the buttons 'AUX', 'OK' in this order.
Child Lock
Grundig CUC2051 CTV General reset with number 7038.
Cancel

Depress and hold the button 'P-' on the RC while

switching on with the mains button.
Default
(Additionally on replacement of the memory, the
Grundig CUC2051 CTV Values
Hotel Mode and the band limits are to be
Entering
deactivated and the AGC and AFC are to be
readjusted).

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC2051 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.
Manufacturer Model Chassis Product Mode Enter
Depress and hold the 'i' button on the RC while
OSD
Grundig CUC2051 CTV switching on with the mains button. Set the
position
OSD position in the menu and store with 'OK'.
Menu guide: 'i', 'Dialog Center', 'Service', 'Only
Grundig CUC2051 CTV Service Mode
for retailer', 'Code 8500'.
Child Lock
Grundig CUC6300 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the 'i' button on the RC while
Default
switching on with the mains button. Menu guide:
Grundig CUC6300 CTV Values
'Horizontal Position', 'OK', 'OK', press 'i' to leave
Entering
the menu.

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC6300 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'i' button on the RC while

OSD
Grundig CUC6300 CTV switching on with the mains button. Set the
position
OSD position in the menu and store with 'OK'.
Child Lock
Grundig CUC6301 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the 'i' button on the RC while
Default
switching on with the mains button. Menu guide:
Grundig CUC6301 CTV Values
'Horizontal Position', 'OK', 'OK', press 'i' to leave
Entering
the menu.

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC6301 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'i' button on the RC while

OSD
Grundig CUC6301 CTV switching on with the mains button. Set the
position
OSD position in the menu and store with 'OK'.
Child Lock
Grundig CUC6310 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the 'i' button on the RC while
Default
switching on with the mains button. Menu guide:
Grundig CUC6310 CTV Values
'Horizontal Position', 'OK', 'OK', press 'i' to leave
Entering
the menu.

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC6310 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'i' button on the RC while

OSD
Grundig CUC6310 CTV switching on with the mains button. Set the
position
OSD position in the menu and store with 'OK'.
Manufacturer Model Chassis Product Mode Enter

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC6330 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC6331 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Child Lock
Grundig CUC6360 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the button 'P-' on the RC while
Default
switching on with the mains button. (This is
Grundig CUC6360 CTV Values
only possible once on replacement of the NVM
Entering
or uP).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC6360 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.

Depress and hold button 'P/C' on the RC while

switching on with the mains button. In the menu
Grundig CUC6360 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'P/C' button on the RC

Grundig CUC6360 CTV Service Mode
while switching on with the mains button.
Volume
Press and hold the 'AUX' button on the RC while
Grundig CUC6360 CTV Offset
switching the TV on with the mains button.
Cancel
Child Lock
Grundig CUC6365 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the button 'P-' on the RC while
Default
switching on with the mains button. (This is
Grundig CUC6365 CTV Values
only possible once on replacement of the NVM
Entering
or uP).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC6365 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.

Depress and hold button 'P/C' on the RC while

switching on with the mains button. In the menu
Grundig CUC6365 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'P/C' button on the RC

Grundig CUC6365 CTV Service Mode
while switching on with the mains button.
Volume
Press and hold the 'AUX' button on the RC while
Grundig CUC6365 CTV Offset
switching the TV on with the mains button.
Cancel
Manufacturer Model Chassis Product Mode Enter
Child Lock
Grundig CUC6380 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the button 'P-' on the RC while
Default
switching on with the mains button. (This is
Grundig CUC6380 CTV Values
only possible once on replacement of the NVM
Entering
or uP).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC6380 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.

Depress and hold button 'P/C' on the RC while

switching on with the mains button. In the menu
Grundig CUC6380 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'P/C' button on the RC

Grundig CUC6380 CTV Service Mode
while switching on with the mains button.
Volume
Press and hold the 'AUX' button on the RC while
Grundig CUC6380 CTV Offset
switching the TV on with the mains button.
Cancel
Child Lock
Grundig CUC6450 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the button 'P-' on the RC while
Default
switching on with the mains button. (This is
Grundig CUC6450 CTV Values
only possible once on replacement of the NVM
Entering
or uP).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC6450 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.

Depress and hold button 'P/C' on the RC while

switching on with the mains button. In the menu
Grundig CUC6450 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'P/C' button on the RC

Grundig CUC6450 CTV Service Mode
while switching on with the mains button.
Volume
Press and hold the 'AUX' button on the RC while
Grundig CUC6450 CTV Offset
switching the TV on with the mains button.
Cancel
Child Lock
Grundig CUC6460 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the button 'P-' on the RC while
Default
switching on with the mains button. (This is
Grundig CUC6460 CTV Values
only possible once on replacement of the NVM
Entering
or uP).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC6460 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Manufacturer Model Chassis Product Mode Enter

Depress and hold button 'P/C' on the RC while

switching on with the mains button. In the menu
Grundig CUC6460 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'P/C' button on the RC

Grundig CUC6460 CTV Service Mode
while switching on with the mains button.
Volume
Press and hold the 'AUX' button on the RC while
Grundig CUC6460 CTV Offset
switching the TV on with the mains button.
Cancel
Child Lock
Grundig CUC6469 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Depress and hold the button 'P-' on the RC while
Default
switching on with the mains button. (This is
Grundig CUC6469 CTV Values
only possible once on replacement of the NVM
Entering
or uP).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC6469 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.

Depress and hold button 'P/C' on the RC while

switching on with the mains button. In the menu
Grundig CUC6469 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'P/C' button on the RC

Grundig CUC6469 CTV Service Mode
while switching on with the mains button.
Volume
Press and hold the 'AUX' button on the RC while
Grundig CUC6469 CTV Offset
switching the TV on with the mains button.
Cancel
Depress and hold down button 'P-' on the RC
Default
and switch the TV on from Standby with the
Grundig CUC7300 CTV Values
local 'P+' button. (This is only possible once on
Entering
replacement of the NVM or uP).
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC7300 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Depress and hold button 'P/C' while switching
Grundig CUC7300 CTV Hotel Mode on from Standby with button 'P+' on the TV. Set
the Hotel Mode to 'OFF' with 'OK'.
Volume Depress and hold the 'AUX' button on the RC
Grundig CUC7300 CTV Offset while switching the TV on from Standby with
Cancel the local 'P+' button.

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC7301 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold down button 'P-' on the RC

Default
and switch the TV on from Standby with the
Grundig CUC7302 CTV Values
local 'P+' button. (This is only possible once on
Entering
replacement of the NVM or uP).
Manufacturer Model Chassis Product Mode Enter
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC7302 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Depress and hold button 'P/C' while switching
Grundig CUC7302 CTV Hotel Mode on from Standby with button 'P+' on the TV. Set
the Hotel Mode to 'OFF' with 'OK'.
Volume Depress and hold the 'AUX' button on the RC
Grundig CUC7302 CTV Offset while switching the TV on from Standby with
Cancel the local 'P+' button.
Depress and hold button 'i' on the RC while
Band Limits switching on with the mains button. Move the
Grundig CUC7303 CTV
Cancelling bar to 'AGC' in the Service Menu and operate
the buttons 'AUX', 'OK' in this order.

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC7303 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'i' button on the RC while

OSD
Grundig CUC7303 CTV switching on with the mains button. Set the
position
OSD position in the menu and store with 'OK'.
Depress and hold button 'i' on the RC while
Band Limits switching on with the mains button. Move the
Grundig CUC7305 CTV
Cancelling bar to 'AGC' in the Service Menu and operate
the buttons 'AUX', 'OK' in this order.

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC7305 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Depress and hold the 'i' button on the RC while

OSD
Grundig CUC7305 CTV switching on with the mains button. Set the
position
OSD position in the menu and store with 'OK'.

Depress and hold button 'i' on the RC while

switching on with the mains button. In the menu
Grundig CUC7350 CTV Hotel Mode line 'HOTEL' select 'ON' and leave the menu with
button 'i'. Cancelling the Hotel Mode: Repeat
the steps above but change 'HOTEL' to 'OFF'.

Child Lock
Grundig CUC7851 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC7851 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Child Lock
Grundig CUC7880 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC7880 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Child Lock
Grundig CUC7890 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Manufacturer Model Chassis Product Mode Enter
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC7890 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Child Lock
Grundig CUC7951 CTV Press VOL+, VOL-, PR-, PR+, OK.
Cancel
Press button 'i' to call up the 'Dialog Center' -->
EPROM OK. The version number is shown by pressing
Grundig CUC7951 CTV
Version Nr. the 'AUX' button. The index 01 of the part nr.
(19798-300.01) indicates the EPROM version.
Press the 'CODE' button on the remote control
Electronic handset. Enter the numers 4 9 3 4 on the
Grundig GV200 to GV250 VCR
Lock Cancel remote control handset in this order and confirm
with the 'OK' button. Press the STOP button.
Press the 'STANDBY' button on the remote
Electronic
Grundig GV201-1 VCR control handset until 'FREE' is indicated on the
Lock Cancel
display of the video recorder.
GV25SV/5 Electronic Press the 'STAND-BY' button on the RC until
Grundig VCR
GV45SV/5 Lock Cancel 'FREE' appears on the display of the recorder.
Enter the numbers 4 9 3 4 on the remote control
GV280PC Electronic
Grundig VCR handset in this order and confirm with the
GV280S Lock Cancel
button 'OK'. Press the STOP button.
GV400 With the video recorder switched off (Stand-by)
Electronic
Grundig GV400GB VCR press the Stop button on the RC until 'UNLO'
Lock Cancel
GV400OST appears on the display of the recorder.
With the video recorder switched off (Stand-by)
GV4000VPS Electronic
Grundig VCR press the Stop button on the RC until 'UNLO'
GV4001 Lock Cancel
appears on the display of the recorder.
With the video recorder switched off (Stand-by)
Electronic
Grundig GV4003VPS VCR press the Stop button on the RC until 'FREE'
Lock Cancel
appears on the display of the recorder.
Press the 'CODE' button on the remote control
handset. Enter the numers 4 9 3 4 on the
GV400VPS Electronic remote control handset in this order and confirm
Grundig VCR
GV401VPT Lock Cancel with the 'OK' button. Press the 'STAND-BY'
button or disconnect the recorder from the
mains.

GV4010SV-VPT Press the 'CODE' button on the remote control

GV4092.. handset. Enter the numers 4 9 3 4 on the
GV4192VPS Electronic remote control handset in this order and confirm
Grundig VCR
GV4200SV-VPT Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV4400HiFi button or disconnect the recorder from the
GV4592.. mains.
With the video recorder switched off (Stand-by)
Electronic
Grundig GV402 VCR press the Stop button on the RC until 'UNLO'
Lock Cancel
appears on the display of the recorder.
Press the 'CODE' button on the remote control
handset. Enter the numers 4 9 3 4 on the
GV404SV
Electronic remote control handset in this order and confirm
Grundig GV405EURO VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV406EURO
button or disconnect the recorder from the
mains.
With the video recorder switched off (Stand-by)
Electronic
Grundig GV410 VCR press the Stop button on the RC until 'UNLO'
Lock Cancel
appears on the display of the recorder.
Manufacturer Model Chassis Product Mode Enter
Press the 'CODE' button on the remote control
handset. Enter the numers 4 9 3 4 on the
GV410VPS Electronic remote control handset in this order and confirm
Grundig VCR
GV411 Lock Cancel with the 'OK' button. Press the 'STAND-BY'
button or disconnect the recorder from the
mains.
Press and hold the 'STAND-BY' button on the
Electronic
Grundig GV411-1 VCR RC (ca. 5s), until 'UNLOCKED' appears on the
Lock Cancel
display of the recorder.
With the video recorder switched off (Stand-by)
GV411OST Electronic
Grundig VCR press the Stop button on the RC until 'UNLO'
GV412 Lock Cancel
appears on the display of the recorder.
Press the 'CODE' button on the remote control
GV414SV handset. Enter the numers 4 9 3 4 on the
GV415EURO Electronic remote control handset in this order and confirm
Grundig VCR
GV416EURO Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV420VPT button or disconnect the recorder from the
mains.
With the video recorder switched off (Stand-by)
GV430 Electronic
Grundig VCR press the Stop button on the RC until 'UNLO'
GV430GB Lock Cancel
appears on the display of the recorder.
Press the 'CODE' button on the remote control
handset. Enter the numers 4 9 3 4 on the
GV430VPS
Electronic remote control handset in this order and confirm
Grundig GV434SV VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV435EURO
button or disconnect the recorder from the
mains.

GV440.. Press the 'CODE' button on the remote control

GV450.. handset. Enter the numers 4 9 3 4 on the
GV460.. Electronic remote control handset in this order and confirm
Grundig VCR
GV464.. Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV465EURO button or disconnect the recorder from the
GV470.. mains.

Press the 'CODE' button on the remote control

GV500.. handset. Enter the numers 4 9 3 4 on the
GV501VPT Electronic remote control handset in this order and confirm
Grundig VCR
GV505EURO Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV506EURO button or disconnect the recorder from the
mains.
GV5000
GV5000GB Electronic Press the 'STAND-BY' button on the RC until
Grundig VCR
GV5000VPS Lock Cancel 'FREE' appears on the display of the recorder.
GV5000VPS/5
GV5002VPS
GV5003 Electronic Press the 'STAND-BY' button on the RC until
Grundig VCR
GV5008 Lock Cancel 'FREE' appears on the display of the recorder.
GV5050
Press the 'CODE' button on the remote control
GV5050SV handset. Enter the numers 4 9 3 4 on the
GV5050SV/1 Electronic remote control handset in this order and confirm
Grundig VCR
GV5055EURO Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV5095.. button or disconnect the recorder from the
mains.
Manufacturer Model Chassis Product Mode Enter
GV510SV
GV511
Press the 'CODE' button on the remote control
GV515EURO
handset. Enter the numers 4 9 3 4 on the
GV530..
Electronic remote control handset in this order and confirm
Grundig GV535EURO VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV540..
button or disconnect the recorder from the
GV545EURO
mains.
GV560..
GV565EURO
Electronic Press the 'STAND-BY' button on the RC until
Grundig GV5300.. VCR
Lock Cancel 'FREE' appears on the display of the recorder.
Press the 'CODE' button on the remote control
handset. Enter the numers 4 9 3 4 on the
GV5395..
Electronic remote control handset in this order and confirm
Grundig GV5400.. VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV5695HiFi
button or disconnect the recorder from the
mains.
GV600
GV630
GV640HiFi
GV640NIC
Press the 'CODE' button on the remote control
GV645EURO
handset. Enter the numers 4 9 3 4 on the
GV650HiFi
Electronic remote control handset in this order and confirm
Grundig GV660HiFi VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV660NIC
button or disconnect the recorder from the
GV665EURO
mains.
GV670SHiFi
GV670SNIC
GV690SHiFi
GV690SNIC
Press the 'CODE' button on the remote control
GV6096SV
handset. Enter the numers 4 9 3 4 on the
GV6096SV/1
Electronic remote control handset in this order and confirm
Grundig GV6396SV VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
GV6596HiFi
button or disconnect the recorder from the
GV6596NIC
mains.

Press the 'CODE' button on the remote control

handset. Enter the numers 4 9 3 4 on the
GV740.. Electronic remote control handset in this order and confirm
Grundig VCR
GV745EURO Lock Cancel with the 'OK' button. Press the 'STAND-BY'
button or disconnect the recorder from the
mains.
Press and hold down the buttons 'STAND-BY'
Electronic and 'SELECT' simultaneously on the RC until
Grundig GV7400.. VCR
Lock Cancel key simbol disappears from the display of the
recorder.
Press the 'CODE' button on the remote control
handset. Enter the numers 4 9 3 4 on the
Electronic remote control handset in this order and confirm
Grundig GV7497NIC VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
button or disconnect the recorder from the
mains.
Press and hold down the buttons 'STAND-BY'
GV8..
Electronic and 'SELECT' simultaneously on the RC until
Grundig KV8.. VCR
Lock Cancel key simbol disappears from the display of the
SE8..
recorder.
Manufacturer Model Chassis Product Mode Enter
Electronic Press the 'STAND-BY' button on the RC until
Grundig GVP600ICNEURO VCR
Lock Cancel 'FREE' appears on the display of the recorder.
KV5001VPS/5 Electronic Press the 'STAND-BY' button on the RC until
Grundig VCR
KV5301VPS/5 Lock Cancel 'FREE' appears on the display of the recorder.
With the video recorder switched off (Stand-by)
MV4005 Electronic
Grundig VCR press the Stop button on the RC until 'UNLO'
MV4105 Lock Cancel
appears on the display of the recorder.
Press the 'CODE' button on the remote control
handset. Enter the numers 4 9 3 4 on the
SE4100VPS
Electronic remote control handset in this order and confirm
Grundig SE4104SV VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
SE4120SV
button or disconnect the recorder from the
mains.

Press the 'CODE' button on the remote control

handset. Enter the numers 4 9 3 4 on the
SE5102SV
Electronic remote control handset in this order and confirm
Grundig SE5104SV VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
SE5106HiFi
button or disconnect the recorder from the
mains.

Press the 'CODE' button on the remote control

handset. Enter the numers 4 9 3 4 on the
SE6102SV
Electronic remote control handset in this order and confirm
Grundig SE6104SV VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
SE6106HiFi
button or disconnect the recorder from the
mains.

Press the 'CODE' button on the remote control

handset. Enter the numers 4 9 3 4 on the
Electronic remote control handset in this order and confirm
Grundig SE7104SV VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
button or disconnect the recorder from the
mains.
Press and hold down the buttons 'STAND-BY'
Electronic and 'SELECT' simultaneously on the RC until
Grundig SE7105 VCR
Lock Cancel key simbol disappears from the display of the
recorder.
Press the 'CODE' button on the remote control
handset. Enter the numers 4 9 3 4 on the
Electronic remote control handset in this order and confirm
Grundig SE7106HiFi VCR
Lock Cancel with the 'OK' button. Press the 'STAND-BY'
button or disconnect the recorder from the
mains.
Press and hold STOP button on the RC and
Electronic depress the PLAY button on the video recorder.
Grundig TVR3700 VCR
Lock Cancel Press the 'STAND-BY' button or disconnect the
video recorder from the mains.
TVR3701
TVR3705
Electronic Press the cursor buttons on the RC in this
Grundig TVR3710 VCR
Lock Cancel order: VOL+, VOL-, PR+, PR-.
TVR3720
TVR3730
Interconnect the service test points on the
TVR4500 Electronic keyboard control unit for a short period.
Grundig VCR
TVR4510 Lock Cancel Switch the unit off and disconnect it from
mains.
Manufacturer Model Chassis Product Mode Enter
TVR5100
Electronic Press the cursor buttons on the RC in this
Grundig TVR5130 VCR
Lock Cancel order: VOL+, VOL-, PR+, PR-.
TVR5500
Interconnect the service test points on the
Electronic keyboard control unit for a short period.
Grundig TVR5510 VCR
Lock Cancel Switch the unit off and disconnect it from
mains.
Electronic Press the cursor buttons on the RC in this
Grundig TVR5530 VCR
Lock Cancel order: VOL+, VOL-, PR+, PR-.
Switch the video recorder off. Remove the top of
the cabinet. Unplug the B1 connector on the
Electronic sequence control. Switch the recorder on. After
Grundig VS200 to VS267 VCR
Lock Cancel approx. 2 seconds, re-insert the B1 connector.
Switch the video recorder off. Re-fit the top of
the cabinet.
Switch the video recorder off. Remove the top of
the cabinet. Switch the recorder on.
Electronic Interconnect the service test points on the
Grundig VS300 to VS460 VCR
Lock Cancel keyboard control unit for a short period. Press
the STOP button. Switch the video recorder
off. Re-fit the top of cabinet.
Enter the numbers 4 9 3 4 on the remote control
Electronic
Grundig VS500 VCR handset in this order and confirm with the
Lock Cancel
button '0000'. Press the STOP button.

Enter the numbers 4 9 3 4 on the remote control

Electronic
Grundig VS505 to VS510 VCR handset in this order and confirm with the
Lock Cancel
button 'OK'. Press the STOP button.
Switch the video recorder off. Remove the top of
the cabinet. Switch the recorder on.
Electronic Interconnect the service test points on the
Grundig VS520 to VS550 VCR
Lock Cancel keyboard control unit for a short period. Press
the STOP button. Switch the video recorder
off. Re-fit the top of cabinet.
Enter the numbers 4 9 3 4 on the remote control
Electronic
Grundig VS600 to VS960 VCR handset in this order and confirm with the
Lock Cancel
button 'OK'. Press the STOP button.
MUTE --> OK (M) --> TV
ITT STEREO PLUS CTV Service Mode Controls: cursor buttons. Store: OK (M).
Exit: TV
LG MC64 CTV Service Mode Simultaneous press OK on RC & local panel.
LG MC84 CTV Service Mode Simultaneous press OK on RC & local panel.
Art.-Nr. 64420
Simultaneous press CM on the RC & "Service"
66426 66449 TV Service
Loewe. C9000 CTV key on the control panel. Select: MEM IN/OUT.
66450 66460 Mode
Adjust: VOL +/-. Store: X. Exit: TV.
66480 66490
Art.-Nr. 64420
Simultaneous press VT on the RC & "Service"
66426 66449 VT Service
Loewe. C9000 CTV key on the control panel. Select: MEM IN/OUT.
66450 66460 Mode
Adjust: VOL +/-. Store: X. Exit: TV.
66480 66490
On the local control press function key five times
(indication "Service" will appear), afterwards
Loewe. C9003 CTV Service Mode
within a sec. press key "MEN" on the remote
control. Store: X. Exit: TV.
Go to 'SERVICE' in menu and then quick press
Loewe. Q2200 CTV Service Mode 'MENU' on the RC. Select: yellow cursors.
Adjust: +/-. Store: 'X'. Exit: 'TV'.
Manufacturer Model Chassis Product Mode Enter
5585-21A1 MUTE --> OK (M) --> TV
Luxor 7057-27 STEREO PLUS CTV Service Mode Controls: cursor buttons. Store: OK (M).
63/7954 Exit: TV
Press S701 (on board) and button 9 (in 5s).
Mitsubishi CT21M5E CTV Service Mode
Store: '0'. Exit: stand-by.
Select DISPLAY MODE. Press PROCEED.
XExx Press and hold RESET. Then simultaneous
NEC XPxx MON Service Mode press + & -. 'Warning Entering Service Menu…'
XVxx appears. Press PROCEED for enter. Be
careful! You can damage a monitor!
Nokia 6364, 7364 2B-F CTV Service Mode Quick press: --\-, MENU, TV.
In 1s press buttons '-/--', 'MENU', 'TV'. Select:
Nokia EUROSTEREO CTV Service Mode PR+/-. Adjust: VOL+/-. Store: fill-dot-symbol
on RC (near 'i' button). Exit: 'STANDBY'.
63/7168 55A1-0 MUTE --> OK (M) --> TV
Nokia 45H1-0 55Y2-0 STEREO PLUS CTV Service Mode Controls: cursor buttons. Store: OK (M).
63/7157 63/7177 Exit: TV
i --> M --> PROGR.
Nokia STEREO PLUS CTV Service Mode Controls: cursor buttons. Store: M.
Exit: TV
Switch to Standby. Switch off with the mains
switch. Press and hold red button on RC and
Nordmende DC1 CTV Service Mode then switch on with the mains switch (cca 10s).
Select: numbers buttons. Adjust: +/-. Store:
red button. Exit: 'MUTE'.
Switch to Standby. Switch off with the mains
switch. Press and hold red button on RC and
Nordmende DC2 CTV Service Mode then switch on with the mains switch (cca 10s).
Select: numbers buttons. Adjust: +/-. Store:
red button. Exit: 'MUTE'.
After replacement of the MDA2061 (IR73) the
TV receiver acts as folows: a) All programme
storages have stored Ch00. b) The indicator
shows German function characters. c) PAL and
SECAM EAST standard recepcion is possible
(not NTSC and/or SECAM WEST).
If required to change according to paragr. b and
c then switch off the set by the mains switch.
Press both buttons + and - for volume on TV
and simultaneously switch the set on with the
MDA2061
Nordmende Color 3038 F15-03 110° CTV mains switch. Keep the two volume buttons
Replacement
pressed until the display indicates Pr. After 8s
the display indicates __. Now the following
buttons can be presseed on the RC, thus
additional corresponding segments will be
illuminated: Button '1' function symbols indicate
international display. Reversible to German
display with button '2'. Button '5' additional
SECAM WEST and/or NTSC reception
(Multistandard). Reversible to Single Standard
with button '3'. Store: Stand-By.
Switch to Stand By. Switch off with the mains
Nordmende ICC10 CTV Service Mode switch. Press and hold 'VT' on RC then switch
on with the mains switch.
Manufacturer Model Chassis Product Mode Enter
Switch off TV with RC (st-by). Switch off TV with
main switch. Wait a few sec till ST_BY LED
switch off. Simultaneous press blue button on
Nordmende ICC9 CTV Service Mode
RC and switch on TV with main switch. Press
blue button again. (WARNING: scart must be
free.)
Simultaneous press red & blue buttons on RC
then (in 5 sec.) simultaneously press P- & P+
Palladium TV-100 CTV Service Mode
on local keyboard. Commands: arrows. Store:
OK. Exit: TV.
In Sound-Menu Low-tone-regel to MAX and
High-tone-regel to MIN. Press VOL- on TV
Panasonic EURO-1 CTV Service Mode and RESET on RC in some time. Select: red
and green buttons. Adjust: yellow and blue
buttons. Store: 'STORE'. Exit: switch off.
In Sound-Menu Low-tone-regel to MAX and
High-tone-regel to MIN. Press 'F' button on TV.
Then press VOL- on TV and REVEAL on RC in
Panasonic EURO-2 CTV Service Mode
some time. Select: red and green buttons.
Adjust: yellow and blue buttons. Store:
'STR'. Exit: 'N' on RC.
ON: Press simultaneously 'OFF TIMER' on RC
MX-3 and 'CH.UP' local.
Panasonic CTV Hotel Mode
MX-3C OFF: Press simultaneously 'OFF TIMER' on RC
and 'VOL-' local.
MX-3 Simultaneously press 'RECALL' on RC and
Panasonic CTV Service Mode
MX-3C 'VOL-' local. Exit: 'NORMAL' on RC.
ON: Set HOTEL ON in Service Menu. Select
programm 38. Simultaneous press (3 sec)
Philips ANUBIS B CTV Hotel Mode
INSTALL & P- on local keyboard.
OFF: Set HOTEL OFF in Service Menu.
Simultaneously press VOL+ & P- on RC.
Philips ANUBIS B CTV Service Mode
Exit: STANDBY.
OFF: Select programm 38. Simultaneous press
(3 sec) PR+ & VOL- on local keyboard.
Philips Anubis S CTV Hotel Mode
ON: Select programm 38. Simultaneous press
(3 sec) STORE & PR- on local keyboard.
With special service RC. Or short M25, M25
Philips L7.1A CTV Service Mode
on board and then switch on TV. Exit: st-by.
Select program 38 on the TV. Simultaneously
press the keys VOLUME- and VOLUME+ on
Philips L9.1 CTV Hotel Mode
the keyboard of the TV and the OSD key of
the remote control.
This model also supports the 062596 sequence
Philips L9H CTV Service Mode followed by [MENU] (service default) or
[i+]/[OSD] (service mode).
There is a small Service jumper to short on the
small signal PCB. When the TV is in this first
level service mode, you can go in the second
level service mode by pressing both MENU
and - keys on top of the TV at the same time.
Philips MD1.2E CTV Service Mode There you can read much parameters and
proceed with most of the adjustments. In fact
this method let you use an ordinary Remote
control but you also need to open the back
cover. With the special service remote control,
a special code is sent to enter the service mode.
Manufacturer Model Chassis Product Mode Enter

Option 1: In the TV-set itself is a 3-pin connector

with which either SERVICE-DEFAULT or
SERVICE-MODE can be activated. This
connector is depicted 0356 (SERVICE-PINS)
on page K7 (TXT&CONTROL). Shorting pins 1-2
will activate SERVICE-MODE. Shorting pins 2-3
will activate SERVICE-DEFAULT. Option 2:
Activate these modes using the remote control.
Obviously option 2 is the preferred method
because the settings have to be changed using
a remote control anyway.... To activate
SERVICE-DEFAULT: Press 0 6 2 5 9 6 and then
the [menu] button. The message ‘Service Default’
Philips MG3.1E CTV Service Mode
appears and channel ‘SER T’ will be selected.
This only sets some settings to a preset value
(color/brightness/volume and such). This mode
is primarily intended to be used when the non
volatile memory has been replaced. It is then
loaded with the default values. To activate
SERVICE-MODE: Press 0 6 2 5 9 6 and then
the [i+] button. After pressing 0 6 2 5 9 6 the
message ‘Dealer’ should have appeared.
Do not worry about the channel changing while
you press the numbers.
Service technicians have the m
service mode using a special re

Use the standard remote control an key in a

special sequence 0 6 2 5 9 6 followed by
pressing the 'MENU' button. If the main menu
also appears with the service menu just press
Philips 29PT9416 MG7.1 CTV Service Mode 'MENU' again to clear it. The other way is to
short the two service pins on the signal panel
(pins 2 and 3 of connector 0356). The advantage
of this last method is that all the software
protections are turned off.
Use the standard remote control an key in a
special sequence 0 6 2 5 9 6 followed by
Philips Y6 CTV Service Mode pressing the 'MENU' button. If the main menu
also appears with the service menu just press
'MENU' again to clear it.
Without cassette. Press and hold SYSTEM till
Modulator
Philips VR210/58 VCR 'G591' appears. Press and hold CLEAR(CL) till
off
'MOFF' appears. Exit: TV/STANBY.
Without cassette. Press and hold SYSTEM till
Modulator
Philips VR210/58 VCR 'MOFF' appears. Press and hold CLEAR(CL) till
on
'G591' appears. Exit: TV/STANBY.
Child Lock Press CHILD LOCK (key-simbol) on the RC
Philips VR220/58 VCR
Cancel for 5s with the VCR switched on.
Without cassette. Press and hold STOP on the
RC and then press STOP/EJECT on VCR.
Select the line 'MODULATOR' on the TV screen
Modulator
Philips VR220/58 VCR or 'MOD+' in the display with P+/-. In the display
on/off
select 'OFF' / 'MOD-' (modulator off) with VOL-
or 'MOD+' (modulator on). Confirm with OK.
Exit with MENU
Manufacturer Model Chassis Product Mode Enter
Without cassette. Hold the STOP button on the
RC. In addition press the STOP/EJECT button
on the VCR until the pre-set modulator
frequency appears in the display, e.g. 'M591'
(591MHz or 36 ch. UHF). Select line 'OPTIMIZE
Modulator
Philips VR220/58 VCR FREQUENCY' using P+/-. Enter new
preset
modulator frequency with the numbers 0-9. In
line 'SOUND SYSTEM' select the TV system
using VOL+/-. 'G' = PAL B/G. 'K' = SECAM D/K.
Confirm with OK. 'STORED' will appear briefly
on the screen.

Disconect from the mains power supply. Press

Reset to and hold the STANDBY/ON button on the device
Philips VR220/58 VCR factory and reconnect to the mains power supply.
settings Release the button when 'OSD' appears in the
VCR display.
Auto ST-BY
Philips VR400/58 VCR Press and hold STOP till [] appears.
off
Without cassette. Press and hold SYSTEM till
Modulator
Philips VR400/58 VCR 'G591' appears. Press and hold CLEAR(CL) till
off
'MOFF' appears. Exit: TV/STANBY.
Without cassette. Press and hold SYSTEM till
Modulator
Philips VR400/58 VCR 'MOFF' appears. Press and hold CLEAR(CL) till
on
'G591' appears. Exit: TV/STANBY.
Without cassette. VCR st-by. Press and hold
Modulator SYSTEM till 'G591' appears. System change:
Philips VR400/58 VCR
preset SELECT. Freq. Change: P +/-. Store: OK.
Exit: TV/STANBY.
On the local control press function key five times
(indication "Service" will appear), afterwards
Revox D-TV C9003 CTV Service Mode
within a sec. press key "MEN" on the remote
control. Store: X. Exit: TV.
Switch off set with main switch. Switch on set
with main switch and during doing this press
the buttons + and - of volume control on the
ULTRACOLOR
ICC5115ML 110 Combination set's control bord simultaneously until the
Saba T55U42 T55U43 CTV
ICC5116MM 90° Lock Cancel display lights. Display: SS… Press the button
T63U42 T63U43
'S' on the RC. Switch off with RC. Now the
combination lock is unlocked and one can
switch on again in the normal manner.

Switch off TV with RC (st-by). Switch off TV with

main switch. Wait a few sec till ST_BY LED
Saba ICC9 CTV Service Mode switch off. Simultaneous press VT button on RC
and switch on TV with main switch. Press VT
button again. (WARNING: scart must be free.)

Put TV into standby, then turn power off, then

Hotel Mode turn power on whilst holding standby button on
Saba T7032VT TX92 CTV
Cancel remote and step through menus to `vol set` and
increase level to max.
Salora 28N8S 2B-F CTV Service Mode Quick press: --\-, MENU, TV.
MUTE --> OK (M) --> TV
17/21SF 25/28X71
Salora STEREO PLUS CTV Service Mode Controls: cursor buttons. Store: OK (M).
25/28SP50
Exit: TV
Manufacturer Model Chassis Product Mode Enter

CB-14F1 CB-20P30
CB-20H1 CB-20S20
STAND-BY --> DISPLAY --> P.STD -->
CB-21H1 CB-21P30
MUTE --> POWER ON.
Samsung CB-21S20 CB-3373 S15A CTV Service Mode
Controls: VOL +/-, CH +/-. Exit: POWER OFF.
CB-5020 CB-5073
CB-5079 CB-5320
CB-5373 CB-5379

STAND-BY --> P.STD --> HELP --> SLEEP -->

Samsung CK5038 SCT11B CTV Service Mode POWER ON.
Controls: VOL +/-, CH +/-. Exit: STATUS.
STAND-BY --> P.STD --> HELP --> SLEEP -->
POWER ON.
Samsung CX5944 CX6844 SCT12B CTV Service Mode
FACTORY MODE: set PSL=15 and PVA=63.
Controls: VOL +/-, CH +/-. Exit: STATUS
CB-14V10 CB-3373
CB-14V20 CB-5073
CB-20P30 CB-5079
STAND-BY --> P.STD --> HELP --> SLEEP -->
CB-20S10 CB-5373
Samsung SCT13B CTV Service Mode POWER ON.
CB-20S20
Controls: VOL +/-, CH +/-. Exit: STATUS.
CB-21P30
CB-21S10
CB-21S20
PICTURE OFF --> SLEEP --> P.STD -->
Samsung CS7272 SCT51A CTV Service Mode
MUTE --> PICTURE ON
CS-721 PICTURE OFF --> SLEEP --> P.STD -->
Samsung SCT52A CTV Service Mode
CS-723 MUTE --> PICTURE ON
TVP3350 SCV11A STAND-BY --> P.STD --> MENU -->
Samsung CTV/VCR Service Mode
TVP5050 SCV11B SLEEP --> POWER ON
Simultaneous press Service-button on digi-
Schneider DTV 1 CTV Service Mode bord & button C on RC. Selection: Bass +/-.
Adjust: Volume +/-. Store: T. Exit: TV.
Simultaneous press red & blue buttons on RC
then (in 5 sec.) simultaneous press P- & P+
Schneider DTV 100 CTV Service Mode
on local keyboard. Commands: arrows. Store:
OK. Exit: TV.
Like DTV 1 or simultaneous press Service-
button (down right on RC) & C button on RC.
Schneider DTV 2 CTV Service Mode
Selection: Bass +/-. Adjust: Volume +/-. Store:
IDEAL. Exit: TV.
Simultaneous press red & blue buttons on RC
then (in 5 sec.) simultaneous press P- &
Schneider DTV 3 CTV Service Mode
VOL+ on local keyboard. Selection: wheel.
Adjust: ring. Store: red button. Exit: OFF.
Simultaneous press red & blue buttons on RC
then (in 5 sec.) simultaneous press P- &
Schneider TV 4 CTV Service Mode
VOL+ on local keyboard. Selection: P +/-.
Adjust: VOL +/-. Store: auto. Exit: OFF.
Simultaneous press red & blue buttons on RC
then (in 5 sec.) simultaneous press P- &
Schneider STV7128 TV 8 CTV Service Mode
VOL+ on local keyboard. Selection: P +/-.
Adjust: VOL +/-. Store: auto. Exit: OFF.
Simultaneous press red & blue buttons on RC
then (in 5 sec.) simultaneous press P- &
Schneider TV 9 CTV Service Mode
VOL+ on local keyboard. Selection: P +/-.
Adjust: VOL +/-. Store: auto. Exit: OFF.
Schneider STV355FST CTV Service Mode MENU --> SERVICE --> OK --> 089
Manufacturer Model Chassis Product Mode Enter
SEG 11AK18 CTV Service Mode MENU 1 6 7 5
SEG 11AK19 CTV Service Mode MENU 4 7 2 5
MUTE --> OK (M) --> TV
Seleco STEREO PLUS CTV Service Mode Controls: cursor buttons. Store: OK (M).
Exit: TV
Short conntacts 2 & 6 on bord TB connector
Sharp 4BSA CTV Service Mode and press button 'MODE' on RC. Remove short.
Store: auto. Exit: 'MODE'.
Press and hold buttons VOL- and PR+ on the
Sharp 63CS-03S CS CTV Service Mode local keyboard and then switch on with main
switch. Store: 'POWER'.
Press Service-button on Digi-modul. Store:
Sharp D3000 CTV Service Mode
on/off. Exit: Service button.
Short conntacts 2 & 6 on Digi Modul Service
Slot and then press button 'MODE' on RC.
Sharp Euro-DS1 CTV Service Mode
Store: (romb-symbol) on RC. Exit:
standby, switch off, switch on, remove short.
Press and hold buttons VOL- and PR+ on the
Sharp 54AT-15SC CTV Service Mode local keyboard and then switch on with main
switch. Store: 'POWER'.
Locate place for 2 buttons on local keyboard
(main board) S754-MODE and S755-PRESET.
Sharp DV-5401S CTV Service Mode
Enter: short S754 (-SERV-). Commands:
CH +/-. Store: short S755.
Info Center' --> 'Special Functions' --> 'Service'
Siemens FS369M4 CS9409 CTV Service Mode
--> Code Number 089
Programm
Siemens SAT Unlock: Press key-symbol and 6 1 0 1.
Lock
Silva STV355FST CTV Service Mode MENU --> SERVICE --> OK --> 089
Turn on the main power switch of the set while
pressing any two buttons on the front panel.
KV-E2531 'TT' will appear on the upper right corner of the
Sony KV-E2931 AE-2 CTV Service Mode screen. Press the 'MENU' button on the RC.
KV-E3431 In menu select 'DEMO' and press 'OK'. Select
DEVICE coresponding to the adjustment you
need. Store: OK. Exit: turn off.
KV-2170
? --> 5 --> VOL+ --> TV --> MENU
Sony KV-2180 BE4 CTV Service Mode
Exit: 00
KV-2540
Turn on the main power switch of the set while
pressing any two buttons on the front panel.
'TT' will appear on the upper right corner of the
Sony KV-B2911 CTV Service Mode screen. Press the 'MENU' button on the RC.
In menu select 'DEMO' and press 'OK'. Select
DEVICE coresponding to the adjustment you
need. Store: OK. Exit: turn off.
Switch TV to STANDBY.
Sony KV-G21M1 CTV Service Mode
DISPLAY --> 5 --> VOL+ --> POWER

Switch off TV with RC (st-by). Switch off TV with

main switch. Wait a few sec till ST_BY LED
Telefunken ICC9 CTV Service Mode switch off. Simultaneous press VT button on RC
and switch on TV with main switch. Press VT
button again. (WARNING: scart must be free.)

MUTE --> OK (M) --> TV

Telefunken STEREO PLUS CTV Service Mode Controls: cursor buttons. Store: OK (M).
Exit: TV
Manufacturer Model Chassis Product Mode Enter

Switch off TV with RC (st-by). Switch off TV with

main switch. Wait a few sec till ST_BY LED
Telefunken TX-90 CTV Service Mode switch off. Simultaneous press VT button on RC
and switch on TV with main switch. Press VT
button again.

Switch off TV with RC (st-by). Switch off TV with

main switch. Wait a few sec till ST_BY LED
Telefunken TX-91 CTV Service Mode switch off. Simultaneous press VT button on RC
and switch on TV with main switch. Press VT
button again.

Switch to Standby. Switch off with the mains

switch. Press and hold blue button and then
Thomson ICC19 CTV Service Mode
switch on with the mains switch. Press blue
button again. Exit: switch off with mains switch.
Switch to Standby. Switch off with the mains
switch. Press and hold 'PROG-' and 'VOL-' and
Thomson ICC19 CTV Service Mode
then switch on with the mains switch. Exit:
switch off with mains switch.

Switch off TV with RC (st-by). Switch off TV with

main switch. Wait a few sec till ST_BY LED
Thomson ICC9 CTV Service Mode switch off. Simultaneous press VT button on RC
and switch on TV with main switch. Press VT
button again. (WARNING: scart must be free.)

Switch off TV with RC (st-by). Switch off TV with

main switch. Wait a few sec till ST_BY LED
Thomson TX-90 CTV Service Mode switch off. Simultaneous press VT button on RC
and switch on TV with main switch. Press VT
button again.

Switch off TV with RC (st-by). Switch off TV with

main switch. Wait a few sec till ST_BY LED
Thomson TX-91 CTV Service Mode switch off. Simultaneous press VT button on RC
and switch on TV with main switch. Press VT
button again.

Press 'MUTE' button. Press and hold 'MUTE'

button and press 'MENU' on local keyboard.
Toshiba 2150 S5E CTV Service Mode
Select: PR nr.. Adjust: VOL+/-. Store: auto.
Exit: 'STANDBY'. Test picture: 'AV'.
Press 'MUTE' button. Press and hold 'MUTE'
2876DD button and press 'MENU' on local keyboard.
Toshiba CTV Service Mode
2988DG Select: PR+/-. Adjust: VOL+/-. Store: auto.
Exit: 'STANDBY'. Test picture: 'AV'.
Switch on with main switch. Press 'MENU',
'TV', 'i'. If TV is still in st-by press 2x'TV', 'i'.
Universum 6000 CTV Service Mode
Select and adjust with cursors. Store: 'OK'.
Exit: switch off with main switch.