Scribd
Upload
147 views2 pages

AL 6XN Tube and Fittings Specifications

Uploaded by

ah1525
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
147 views2 pages

AL 6XN Tube and Fittings Specifications

Uploaded by

ah1525
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

AL-6XN® TUBING & FITTINGS SPECIFICATIONS

AL-6XN® TUBING SPECIFICATIONS


• Welded tubing in compliance with ASTM A270/A249/B676 and ASME SA249/SB676
• Tubing provided in random lengths, 20 ft. ± 1.0 in. is typical (not less than 17 ft. lengths)
• Full line stencil identification on tubing OD
• Plastic sleeved and capped on polished and electropolished tubing
• MTR according with EN 10204 3.1 with every order
For more specifications, visit csidesigns.com/products/superalloys

AL-6XN TUBING DIMENSIONS AND TOLERANCE


TUBING OD OUTSIDE DIAMETER WALL THICKNESS WALL
NOMINAL SIZE TOLERANCE NOMINAL SIZE THICKNESS
IN MM IN MM IN MM TOLERANCE

1/2 12.7 +/-0.005 +/-0.13 0.065 1.65 +/-10%


3/4 19.05 +/-0.005 +/-0.13 0.065 1.65 +/-10%
1 25.4 +/-0.005 +/-0.13 0.065 1.65 +/-10%
1-1/2 38.1 +/-0.008 +/-0.20 0.065 1.65 +/-10%
2 50.8 +/-0.008 +/-0.20 0.065 1.65 +/-10%
2-1/2 63.5 +/-0.010 +/-0.25 0.065 1.65 +/-10%
3 76.2 +/-0.010 +/-0.25 0.065 1.65 +/-10%
4 101.6 +/-0.015 +/-0.38 0.083 2.11 +/-10%

CONTACT CSI FOR MORE INFORMATION | CSIDESIGNS.COM | [email protected] | + 1.417.831.1411


AL-6XN® TUBING & FITTINGS SPECIFICATIONS

AL-6XN FITTINGS SPECIFICATIONS


• Fittings comply with ASME BPE table DT-3-1

AL-6XN FITTINGS DIMENSIONS AND TOLERANCE


SQUARENESS EQUIVALENT CENTERLINE
NOMINAL OD WALL OFF OFF
FACE TO ANGLE RADIUS
SIZE (IN) (IN) THICKNESS (IN) ANGLE, O PLANE, P
TANGENT, B DEGREE (CLR), R
1/2 ±0.005 +0.005/-0.008 0.005 0.014 1.6 0.030 1.125
3/4 ±0.005 +0.005/-0.008 0.005 0.018 1.4 0.030 1.125
1 ±0.005 +0.005/-0.008 0.008 0.025 1.4 0.030 1.500
1-1/2 ±0.008 +0.005/-0.008 0.008 0.034 1.3 0.050 2.250
2 ±0.008 +0.005/-0.008 0.008 0.043 1.2 0.050 3.000
2-1/2 ±0.010 +0.005/-0.008 0.010 0.054 1.2 0.050 3.750
3 ±0.010 +0.005/-0.008 0.016 0.068 1.3 0.050 4.500
4 ±0.015 +0.008/-0.010 0.016 0.086 1.3 0.060 6.000
GENERAL NOTES:
Tolerance on end-to-end and center-to-dimension E is ±0.050 in. (1.27 mm) for all fittings and process components depicted.
See ASME BPE table DT-3-2 for electropolished wall thickness tolerances.

AL-6XN Dims/Tol REV 6/20

CONTACT CSI FOR MORE INFORMATION | CSIDESIGNS.COM | [email protected] | + 1.417.831.1411

You might also like