User’s

Manual Model PH8HF, PH8HFF

Flow-Through Type Holder

IM 12B07N01-01E

IM 12B07N01-01E
6th Edition
 <INTRODUCTION> i

 INTRODUCTION
This manual covers the PH8HF, PH8HFF Flow-Through Type Holder. Other related items
are described in the following manuals:
Model Title IM No.
PH8ERP KCl Refillable type pH Sensor IM 12B7K1-02E
PH8EFP KCl Filling type pH Sensor IM 12B7J1-01E
PH8EHP pH Sensor for Pure Water IM 12B7J2-01E
PH4,OR4 pH and ORP Sensors IM 12B10B00-01EN
FLXA202,FLXA21 2-Wire Liquid Analyzer IM 12A01A02-01E
PH201G*B Distributor IM 19B1E4-02E
FLXA402 4-Wire Converter IM 12A01F01-02EN
IM 12A01F02-01EN etc.
PH450G pH/ORP Converter IM 12B07C05-01E
PUS400G Ultrasonic Oscillator IM 19C1B3-01E
PH8USF, PH8AL Ultrasonic Oscillator (Explosionproof Type), Alarm Box IM 12B5U2-E
WTB10-PH Terminal Box IM 19D01B01-01E
PH8TBG Terminal Box IM 12B07W01-01E
OR8EFG KCl Filling type OPR Sensor IM 12C07J01-01E
OR8ERG KCl Refillable type OPR Sensor IM 12C04K01-01E
OR8TBG Terminal Box IM 12C04W01-01E

Media No. IM 12B07N01-01E 6th Edition : Nov. 2018 (YK) IM 12B07N01-01E

All Rights Reserved Copyright © 2004, Yokogawa Electric Corporation
ii <INTRODUCTION>

 For the safe use of this equipment

n Safety, Protection, and Modification of the Product
• In order to protect the system controlled by the product and the product itself and ensure
safe operation, observe the safety precautions described in this user’s manual. We assume
no liability for safety if users fail to observe these instructions when operating the product.
• If this instrument is used in a manner not specified in this user’s manual, the protection pro-
vided by this instrument may be impaired.
• Be sure to use the spare parts approved by Yokogawa Electric Corporation (hereafter sim-
ply referred to as YOKOGAWA) when replacing parts or consumables.
• Modification of the product is strictly prohibited.

n Notes on Handling User’s Manuals

• Please hand over the user’s manuals to your end users so that they can keep the user’s
manuals on hand for convenient reference.
• Please read the information thoroughly before using the product.
• The purpose of these user’s manuals is not to warrant that the product is well suited to any
particular purpose but rather to describe the functional details of the product.
• No part of the user’s manuals may be transferred or reproduced without prior written con-
sent from YOKOGAWA.
• YOKOGAWA reserves the right to make improvements in the user’s manuals and product at
any time, without notice or obligation.
• If you have any questions, or you find mistakes or omissions in the user’s manuals, please
contact our sales representative or your local distributor.

n Warning and Disclaimer

The product is provided on an “as is” basis. YOKOGAWA shall have neither liability nor respon-
sibility to any person or entity with respect to any direct or indirect loss or damage arising from
using the product or any defect of the product that YOKOGAWA can not predict in advance.

n Signal Words
The following words are used in this manual.

CAUTION
This symbol gives information essential for understanding the operations and functions.

NOTE
This symbol indicates information that complements the present topic.

IM 12B07N01-01E
 <INTRODUCTION> iii

 After-sales Warranty
n Do not modify the product.
n During the warranty period, for repair under warranty consult the local sales representative
or service office. Yokogawa will replace or repair any damaged parts. Before consulting for
repair under warranty, provide us with the model name and serial number and a description
of the problem. Any diagrams or data explaining the problem would also be appreciated.
• If we replace the product with a new one, we won’t provide you with a repair report.
• Yokogawa warrants the product for the period stated in the pre-purchase quotation Yokoga-
wa shall conduct defined warranty service based on its standard. When the customer site is
located outside of the service area, a fee for dispatching the maintenance engineer will be
charged to the customer.
• Returned goods that have been in contact with process fluids must be decontaminated and
disinfected prior to shipment. Goods should carry a certificate to this effect, for the health
and safety of our employees. Material Safety Data sheets must be included for all compo-
nents of the process to which the sensor have been exposed.
n In the following cases, customer will be charged repair fee regardless of warranty period.
• Failure of components which are out of scope of warranty stated in instruction manual.
• Failure caused by usage of software, hardware or auxiliary equipment, which Yokogawa
Electric did not supply.
• Failure due to improper or insufficient maintenance by user.
• Failure due to modification, misuse or outside-of-specifications operation which Yokogawa
does not authorize.
• Failure due to power supply (voltage, frequency) being outside specifications or abnormal.
• Failure caused by any usage out of scope of recommended usage.
• Any damage from fire, earthquake, storms and floods, lightning, disturbances, riots, warfare,
radiation and other natural changes.
n Yokogawa does not warrant conformance with the specific application at the user site.
Yokogawa will not bear direct/indirect responsibility for damage due to a specific application.
n Yokogawa Electric will not bear responsibility when the user configures the product into
systems or resells the product.
n Maintenance service and supplying repair parts will be covered for five years after the pro-
duction ends. For repair for this product, please contact the nearest sales office described in
this instruction manual.

IM 12B07N01-01E
 <CONTENTS> v

Model PH8HF, PH8HFF

Flow-Through Type Holder
IM 12B07N01-01E 6th Edition

CONTENTS
 INTRODUCTION..............................................................................................i
 For the safe use of this equipment..............................................................ii
 After-sales Warranty....................................................................................iii
1. Specifications............................................................................................ 1-1
1.1 General Specifications...................................................................................... 1-1
1.1.1 PH8HF Flow-through Type Holder..................................................... 1-1
1.1.2 PH8HFF (Explosionproof Type) ......................................................... 1-2
1.2 Model and Suffix codes..................................................................................... 1-3
1.2.1 Flow-Through Type Holder PH8HF.................................................... 1-3
1.2.2 Flow-Through Type Holder (Explosionproof Type) PH8HFF............. 1-4
1.3 External Dimensions......................................................................................... 1-5
2. Installation, Piping and Wiring................................................................. 2-1
2.1 Holder Installation.............................................................................................. 2-1
2.1.1 Installation Site ................................................................................... 2-1
2.1.2 Mounting the Flow-through Type Holder............................................ 2-1
2.2 Process Piping................................................................................................... 2-2
2.2.1 Main Precautions for Piping................................................................ 2-2
2.2.2 Piping Procedure................................................................................ 2-4
2.3 Installing the Sensor.......................................................................................... 2-5
2.4 Cleaner Piping ................................................................................................... 2-5
2.4.1 Piping Precautions.............................................................................. 2-5
2.4.2 Piping Procedure................................................................................ 2-7
2.4.3 Installation of PH8PU1 Washer Pump and Water Tank..................... 2-8
2.5 Wiring.................................................................................................................. 2-8
2.5.1 Ultrasonic Oscillator Circuit Wiring..................................................... 2-8
2.5.2 Solenoid Valve Circuit Wiring.............................................................. 2-8
2.5.3 Wiring for PH8PU1 Washer Pump and Tank...................................... 2-9
3. Maintenance/Inspection........................................................................... 3-1
3.1 Cleaning the Holder........................................................................................... 3-1
3.1.1 Inspecting the O-ring Seal................................................................. 3-1
3.2 Checking the Cleaning Element....................................................................... 3-2
3.2.1 Jet Cleaning Element.......................................................................... 3-2
3.2.2 Cleaning the Brush............................................................................. 3-2

IM 12B07N01-01E
vi <CONTENTS>

3.2.3 Ultrasonic Cleaning Element.............................................................. 3-3

3.2.4 Maintenance of PH8PU1 Washer Pump and Tank ........................... 3-4
Customer Maintenance Parts List.......................................CMPL 12B05N01-01E
Revision Information................................................................................................i

IM 12B07N01-01E
 < 1. Specifications > 1-1

1. Specifications
The Model PH8HF¨ flow-through type holder is used:
• To connect two pipes and provide a “flow-through” path between them.
• To mount a pH sensor; the sensor measures the pH of liquid flowing through the holder.
Holder versions with or without cleaning for the pH sensor - ultrasonic cleaning or air/water jet
cleaning - are available.

1.1 General Specifications

1.1.1 PH8HF Flow-through Type Holder
Applicable sensors:
General pH Sensor PH8ERP, PH8EFP
PH4 Sensor PH4P, PH4PT,PH4F, PH4FT,PH4C, PH4CT
General ORP Sensor OR8ERG, OR8EFG
OR4 Sensor OR4P, OR4C
Note: An adapter is required when using PH4/OR4 sensor.
When using with PH4/OR4 sensor, this holder cannot be used outdoors due to exposure to rain or due to condensation
at a high humid place.
Mounting:
2-inch pipe mounting vertical or horizontal,with 1 set of mounting hard bracket.
Note: Make sure the mounting pipe is firmly installed.
Cleaning method:
Jet cleaning, brush cleaning or ultrasonic cleaning
Note: Brush cleaning and ultrasonic cleaning cannot be used when using PH4/OR4 sensor.
Material:
Holder; Polypropylene or stainless steel(equivalent to SUS316)
O-ring; Fluoro rubber (FKM) or Perfluoroelastomer (FFKM)
Mounting bracket: Stainless steel (equivalent to SUS304)
Cleaning unit (wetted parts);
Ultrasonic;Stainless steel (equivalent to SUS316), titanium or Hastelloy C
Jet; Polypropylene
Brush; Polypropylene, titanium(shaft), Rulon®(bearings)
Weight:
Holder; Approx. 0.4 to 1.7 kg (polypropylene)
Approx. 3 to 6.1 kg (stainless steel)
Mounting bracket; Approx. 0.5 kg
Temperature range:
No Cleaning: -5 to 80 °C (polypropylene)
-5 to 105°C (stainless steel)
With Cleaning: -5 to 80°C
Note: The temperature may be limited by the specifications of the sensor.
Flow rate: 3 to 11 L/min
Note: The flow rate may be limited by the specifications of the sensor.
Pressure: Atmospheric pressure to 500 kPa
Note: The pressure may be limited by the specifications of the sensor.

IM 12B07N01-01E
1-2 < 1. Specifications >

Utility required for cleaning unit:Utility required for cleaning unit:

Type Pressure (kPa) Flow Ratee
Water jet 200 to 400 + Liquid pressure 5 to 20 l/min
Water brush 100 to 250 + Liquid pressure 20 to 30 l/min
Air jet 200 to 400 + Liquid pressure 100 to 300 Nl/min
Air brush 150 to 250 + Liquid pressure 300 to 600 Nl/min
Note 1: Pressure and flow rate must be simultaneously satisfied at the holder inlet port.
Note 2: A large braid-reinforced tube of ø22 x ø15 is recommended for supply due to the flow rate.

1.1.2 PH8HFF (Explosionproof Type)

The holder is used only when using Ultrasonic cleaning system in the explosionproof area.
Use PH8HF when using no cleaning, jet cleaning or brush cleaning.

Applicable sensors:
General pH Sensor PH8ERP, PH8EFP
General ORP Sensor OR8ERG, OR8EFG
Mounting: 2-inch pipe mounting vertical or horizontal, with 1 set of mounting bracket.
Note: Make sure the mounting pipe is firmly installed.
Cleaning method: Ultrasonic cleaning
Material:
Holder; Polypropylene or stainless steel (equivalent to SUS316)
O-ring; Fluoro rubber (FKM) or Perfluoroelastomer (FFKM)
Mounting bracket; Stainless steel (equivalent to SUS304)
Cleaning unit (wetted parts):
Ultrasonic; Stainless steel (equivalent to SUS316), titanium or Hastelloy C
Construction:
TIIS flameproof type (for d2G4 gas) Cable entrance port of terminal box; G 3/4
Weight:
Holder; Approx. 3 to 3.2 kg (polypropylene)
Approx. 5.6 to 7.6 kg (stainless steel)
Mounting bracket; Approx. 0.5 kg
Temperature range: -5 to 80°C
Note: The temperature may be limited by the specifications of the sensor.
Flow rate: 3 to 11 L/min
Note: The flow rate may be limited by the specifications of the sensor.
Pressure: Atmospheric pressure to 500 kPa
Note: The pressure may be limited by the specifications of the sensor.

IM 12B07N01-01E
 < 1. Specifications > 1-3

1.2 Model and Suffix codes

1.2.1 Flow-Through Type Holder PH8HF
Model Suffix Code Option Code Description
PH8HF ................................................. ................ Flow-through type holder
Material (*7) -PP ................ Polypropylene (Refer to note below for selection)
-S3 ................ Stainless steel
-PV ................ Heat-resistant PVC
-TN ................ Titanium
Process Connection -JPT ................ Rc1
-NPT ................ 1 NPT female thread
-J10 ................ JIS 10K 25 FF (*6)
-A15 ................ ANSI Class 150 1 FF flange (for polypropylene holder -PP) (*6)
ANSI Class 150 1 RF flange with serration (for SUS316 holder -S3)
pH Measuring System -T ................ Always -T
Cleaning System -NN ................ None
-S3 ................ For ultrasonic cleaning (Transducer: SUS316) (*1)
-TN ................ For ultrasonic cleaning (Transducer: Titanium) (*2)
-HC ................ For ultrasonic cleaning (Transducer: Hastelloy C) (*3)
-JT ................ For jet cleaning. The solenoid valve must be specified separately
-BR ................ For brush cleaning. The solenoid valve must be specified separately
Cable Length for Ultrasonic Cleaning -NN ................ None
-C1 ................ 1m
-C3 ................ 3m
-C6 ................ 7m
-C7 ................ 10m
-C8 ................ 15m
-C9 ................ 20m
Connector for Jet or Brush Cleaning -JP ................ Rc1/2
-NP ................ 1/2 NPT
Style Code *A ................... Style A
Option Special Mounting /MF1 Mounting bracket (stainless steel) (*5)
O-ring /PF Perfluoroelastomer (FFKM) (*4)

*1: General purpose (Normal pH 3 to 14)

*2: For salt water
*3: For acid (Normal pH 0 to 4)
*4: Choose Perfluoroelastomer (FFKM) when this holder is used in organic solvent, high alkali or high temperature alkali.
*5: Mounting bracket is generally not required when the stainless steel holder is installed in-line in a pipe
It is required where the holder is installed in a sampling rack (in which case the U-bolt included in /MF1 in not used).
*6: Only mating dimensioms are according to flange standard.
*7: Criteria for material selection (-PP or -S3)
In general, polypropylene is recommended from the viewpoint of chemical resistance.
However stainless steel is recommend in any of the following cases:
• The liquid contains organic reagent, oxidizing agents, etc., which can attack polypropylene.
• The temperature/pressure correlation of the process condition falls within the hatched area of the diagram shown right.
• The use of polypropylene is not reasonable from a viewpoint of strength or past experience.
For stainless steel, normally a 3 to 14 pH value is recommended.
105
100

Stainless Steel
80

60
(°C)
40
Temperature

20 Polypropylene
(or Stainless Steel)
0 100 200 300 400 500
Pressure (kPa)

IM 12B07N01-01E
1-4 < 1. Specifications >

1.2.2 Flow-Through Type Holder (Explosionproof Type)

PH8HFF
[Style: S2]
Model Suffix Code Option Code Description
PH8HFF ................................................. ................ Flow-through type holder
Material (*7) -PP ................ Polypropylene (Refer to note below for selection)
-S3 ................ Stainless steel
Process Connection -JPT ................ Rc1
-NPT ................ 1 NPT female thread
-J10 ................ JIS 10K 25 FF flange
-A15 ................ ANSI Class 150 1 FF flange equivalent (for polypropylene holder -PP)
ANSI Class 150 1 RF Flange with serration (for SUS316 holder -S3)
pH Measuring System -T ................ Always -T
Cleaning System (*4) -S3 ................
(SUS316 transducer) (*1)
(Ultrasonic cleaning only) -TN ................
(Titanium transducer) (*2)
-HC ................
(Hastelloy C transducer) (*3)
Explosion Protection -JS ................
TIIS Flameproof (d2G4)
Style Code *A ................... Style A
Option Special Mounting /MF1 Mounting bracket (stainless steel) (*6)
Flameproof Packing /PG2 JIS flameproof packing adapter 3/4 inch
Tag Plate /SCT Stainless steel tag plate
O-ring /PF Perfluoroelastomer (FFKM) (*5)

*1: General purpose (Normal pH 3 to 14)

*2: For salt water
*3: For acid (Normal pH 0 to 4)
*4: Use PH8HS for no cleaning, Jet cleaning or Brush cleaning.
*5: Choose Perfluoroelastomer (FFKM) when this holder is used in organic solvent, high alkali or high temperature alkali.
*6: Mounting bracket is generally not required when the stainless steel holder is installed in-line in a pipe
It is required where the holder is installed in a sampling rack (in which case the U-bolt included in /MF1 in not used).
*7: Criteria for material selection (-PP or -S3)
In general, polypropylene is recommended from the viewpoint of chemical resistance.
However stainless steel is recommend in any of the following cases:
• The liquid contains organic reagent, oxidizing agents, etc., which can attack polypropylene.
• The temperature/pressure correlation of the process condition falls within the hatched area of the diagram shown right.
• The use of polypropylene is not reasonable from a viewpoint of strength or past experience.
For stainless steel, normally a 3 to 14 pH value is recommended.

105
100

Stainless Steel
80

60
(°C)
40
Temperature

20 Polypropylene
(or Stainless Steel)
0 100 200 300 400 500
Pressure (kPa)

CAUTION
Select the material of wetted parts with careful consideration of process characteristics.
Inappropriate selection may cause leakage of process fluids, which greatly affects facilities.
Considerable care must be taken particularly in the case of strongly corrosive process fluid such
as hydrochloric acid, sulfuric acid, hydrogen sulfide, and sodium hypochlorite. If you have any
questions about the wetted part construction of the product, be sure to contact Yokogawa.

IM 12B07N01-01E
 < 1. Specifications > 1-5

1.3 External Dimensions

1. PH8HF - PP - ¨PT - T - NN - NN, PH8HF - S3 - ¨PT - T - NN - NN UNIT: mm
Øa
(pH sensor)

A Screw

O-Ring
Outlet

Ød
h
110±1

Inlet

O-Ring
100±1

Model and Code A Screw a d g h Weight

PH8HF-PP-JPT-T-NN-NN Rc1 80 Approx. 60 Approx. 70 Approx. 250 Approx. 0.4kg
PH8HF-PP-NPT-T-NN-NN 1NPT 80 Approx. 60 Approx. 70 Approx. 250 Approx. 0.4kg
PH8HF-S3-JPT-T-NN-NN Rc1 70 Approx. 60 Approx. 70 Approx. 243 Approx. 3kg
PH8HF-S3-NPT-T-NN-NN 1NPT 70 Approx. 60 Approx. 70 Approx. 243 Approx. 3kg

□ Mounting Bracket (Option Code : /MF1) Weight : Approx. 0.5 kg

Bracket (Thickness : 3)

Mounting holes for holder

26
6-Ø10 holes

75 75
140

70±0.3
45 45
10

70±0.3
92
Approx. 82
2B(O.D. 60.5) Pipe Holes Dimension for Wall Mounting
Approx. 130

Figure 1.1 Flow-Through Type Holder

IM 12B07N01-01E
1-6 < 1. Specifications >

2. PH8HF - PP - ¨1¨ - T - NN – NN, PH8HF - S3 - ¨1¨ - T - NN - NN UNIT: mm

Øa
(pH sensor) 4-ØD hole

O-Ring Outlet ØB ØA
Ød

h
110±1

Inlet C

150±1
O-Ring

Model and Code A B C D E a d g h Weight

PH8HF-PP-J10-T-NN-NN 125 90 14 19 - 80 Approx. 60 Approx. 70 Approx. 250 Approx. 0.6kg
PH8HF-PP-A15-T-NN-NN 108 79.4 14.2 15.7 - 80 Approx. 60 Approx. 70 Approx. 250 Approx. 0.6kg
PH8HF-S3-J10-T-NN-NN 125 90 14 19 - 70 Approx. 60 Approx. 70 Approx. 243 Approx. 5kg
PH8HF-S3-A15-T-NN-NN 108 79.2 14.2 15.7 2 70 Approx. 60 Approx. 70 Approx. 243 Approx. 5kg

□ Mounting Bracket (Option Code : /MF1) Weight : Approx. 0.5 kg

Bracket (Thickness : 3)

Mounting holes for holder

26 6-Ø10 holes

75 75
140

70±0.3
45 45
10

70±0.3
92
Approx. 82
2B(O.D. 60.5) Pipe
Approx. 130 Holes Dimension for Wall Mounting

Figure 1.2 Flow-Through Type Holder (with Flange)

IM 12B07N01-01E
 < 1. Specifications > 1-7
PH8HF - PV - ¨1¨ - T - NN – NN UNIT: mm

ø80
(Sensor) 4-øD hole
9

11
25

O-Ring
Outlet
ø60 øB øA

165
Approx.
234 110±1

Inlet C

54

150±1

Model and Code A B C D Weight

PH8HF-PV-J10-h-NN-NN 125 90 14 19 Approx. 0.7 kg
PH8HF-PV-A15-h-NN-NN 108 79.2 14.2 15.7 Approx. 0.7 kg

Mounting Bracket (Option Code : /MF1) Weight : Approx. 0.5 kg

The external dimensions refer to PH8HF-PP-¨1¨-T-NN–NN, PH8HF- S3-¨1¨-T-NN-NN.
Figure 1.2 Flow-Through Type Holder (with Flange) (2)

IM 12B07N01-01E
1-8 < 1. Specifications >

PH8HF - TN - ¨1¨ - T - NN – NN UNIT: mm

ø70
(Sensor) Washer 4-øD hole
8

6
26

O-Ring ø34 Outlet

ø48.6 øE øB øA

76
210 Approx.
219
1
160±1
C

Inlet
110±1

Model and Code A B C D E Weight

PH8HF-TN-J10-h-NN-NN 125 90 14 19 68.5 Approx. 3kg
PH8HF-TN-A15-h-NN-NN 108 79.2 14.2 15.7 57.5* Approx. 3kg
*: With serrations
F1.2_3E_TN1.ai

 Mounting Hardware (Option Code : /MF1) Weight : Approx. 0.5kg

Bracket (Thickness : 3)

Mounting holes for holder

6-ø10 hole
26

75
140
75
70±0.3

45
45 10

70±0.3
92

Approx. 70
2B(O.D. 60.5) Pipe Holes Dimension for Wall Mounting
Approx. 118

Figure 1.2 Flow-Through Type Holder (with Flange) (3)

IM 12B07N01-01E
 < 1. Specifications > 1-9
2.1 PH8HF - ¨¨- ¨PT - T - ¨¨ – ¨P, PH8HF - ¨¨- ¨1¨ - T - ¨¨ - ¨P UNIT: mm
Øa
(pH sensor)

A Screw

O-Ring
Outlet

Ød
h 110±1

Inlet

k
O-Ring

Approx. 47

□ Rc 1/2 (Suffix Code : -JP) 100±1

□ Rc 1/2 NPT (Suffix Code : -NP)

Model and Code A Screw a d g h k Weight

PH8HF-PP-JPT-T-□□-□P Rc1 80 Approx. 60 Approx. 70 Approx. 250 15 Approx. 1.4kg
PH8HF-S3-JPT-T-□□-□P Rc1 70 Approx. 60 Approx. 70 Approx. 245 17 Approx. 4kg
PH8HF-PP-NPT-T-□□-□P 1NPT 80 Approx. 60 Approx. 70 Approx. 250 15 Approx. 1.4kg
PH8HF-S3-NPT-T-□□-□P 1NPT 70 Approx. 60 Approx. 70 Approx. 245 17 Approx. 4kg

Øa
(pH sensor) 4-ØD hole

O-Ring Outlet ØB ØA
Ød

110±1
h
E
Inlet C

O-Ring
Approx. 47

□ RC 1/2 (Suffix Code : -JP) 150±1

□ 1/2 NPT (Suffix Code : -NP)

Model and Code A B C D E a d g h k Weight

PH8HF-PP-J10-T-□□-□P 125 90 14 19 - 80 Approx. 60 Approx. 70 Approx. 250 15 Approx. 1.6kg
PH8HF-S3-J10-T-□□-□P 125 90 14 19 - 70 Approx. 60 Approx. 70 Approx. 245 17 Approx. 6kg
PH8HF-PP-A15-T-□□-□P 108 79.4 14.2 15.7 - 80 Approx. 60 Approx. 70 Approx. 250 15 Approx. 1.6kg
PH8HF-S3-A15-T-□□-□P 108 79.2 14.2 15.7 2 70 Approx. 60 Approx. 70 Approx. 245 17 Approx. 6kg

F1.2.1.ai

Figure 1.2.1 Flow-Through Type Holder (with Jet, Brush Cleaner)

IM 12B07N01-01E
1-10 < 1. Specifications >

2.2 PH8HF - ¨¨- ¨PT - T - ¨¨ – C¨, PH8HF - ¨¨- ¨1¨ - T - ¨¨ - C¨ UNIT: mm

Øa
(pH sensor)

A Screw

O-Ring
Outlet

Ød
110±1
h

Inlet

Cable length (I) g

(Code: C□)
1m (C1) k
3m (C3)
5m (C5)
7m (C6)
10m (C7)
15m (C8) l
100±1
20m (C9)
Cable weigth; Approx. 0.1kg/m

Mode and Code A Screw a d g h k Weight

PH8HF-PP-JPT-T-□□-C□ Rc1 80 Approx. 60 Approx. 70 Approx. 250 15 Approx. 1.5kg
PH8HF-S3-JPT-T-□□-C□ Rc1 70 Approx. 60 Approx. 70 Approx. 245 17 Approx. 4.1kg
PH8HF-PP-NPT-T-□□-C□ 1NPT 80 Approx. 60 Approx. 70 Approx. 250 15 Approx. 1.5kg
PH8HF-S3-NPT-T-□□-C□ 1NPT 70 Approx. 60 Approx. 70 Approx. 245 17 Approx. 4.1kg

Øa
(pH sensor) 4-ØD hole

O-Ring Outlet ØB ØA
Ød

110±1
h
E
Inlet C

Cable length (I)

g
(Code: C□)
1m (C1)
3m (C3) k
5m (C5)
7m (C6)
10m (C7)
15m (C8) l
20m (C9) 150±1
Cable weigth; Approx. 0.1kg/m

Model and Code A B C D E a d g h k Weight

PH8HF-PP-J10-T-□□-C□ 125 90 14 19 - 80 Approx. 60 Approx. 70 Approx. 250 15 Approx. 1.7kg
PH8HF-S3-J10-T-□□-C□ 125 90 14 19 - 70 Approx. 60 Approx. 70 Approx. 245 17 Approx. 6.1kg
PH8HF-PP-A15-T-□□-C□ 108 79.4 14.2 15.7 - 80 Approx. 60 Approx. 70 Approx. 250 15 Approx. 1.7kg
PH8HF-S3-A15-T-□□-C□ 108 79.2 14.2 15.7 2 70 Approx. 60 Approx. 70 Approx. 245 17 Approx. 6.1kg
F1.2.2.ai

Figure 1.2.2 Flow-Through Type Holder (with Ultrasonic Cleaner)

IM 12B07N01-01E
 < 1. Specifications > 1-11
3. PH8HFF - ¨¨ - ¨PT - T - ¨¨ - JS UNIT: mm
Øa
(pH sensor)
b
c
e A Screw
G 3/4(Wiring hole)
74
28 42 69
O-Ring Outlet
165
Ød h
Ø80 110±1

Inlet

g
□ Flameproof Packing Adaptor f
Ø21.7 (Code : /PG2)

Approx. 231
Approx. 95

100 100±1

Model and Code A Screw a b c d e f g h Weight

PH8HFF-PP-JPT-T-□□-JS Rc1 80 9 11 60 25 30 70 Approx. 250 Approx. 3kg
PH8HFF-S3-JPT-T-□□-JS Rc1 70 10 6 60.5 26 26 69 Approx. 245 Approx. 5.6kg
PH8HFF-PP-NPT-T-□□-JS 1NPT 80 9 11 60 25 30 70 Approx. 250 Approx. 3kg
PH8HFF-S3-NPT-T-□□-JS 1NPT 70 10 6 60.5 26 26 69 Approx. 245 Approx. 5.6kg

□ Mounting Bracket (Option Code : /MF1) Weight : Approx. 0.5 kg

Bracket(Thickness : 3)

Mounting holes for holder

26 6-Ø10 holes

75 75
140

70±0.3

45 45
10

70±0.3
92
Approx. 82
2B(O.D. 60.5) Pipe Holes Dimension for Wall Mounting
Approx. 130

Figure 1.3 Flow-Through Type Holder (with Fameproof type Ultrasonic Cleaner)

IM 12B07N01-01E
 1-12 < 1. Specifications >

4. PH8HFF - ¨¨ - ¨1¨ - T - ¨¨ - JS UNIT: mm

Øa
(pH sensor) 4-ØD hole
b
c
e
G3/4 (Wiring hole)
74 Outlet
28 42 69 ØB ØA
O-Ring Ød

165 Ø80 h 110±1

E
Inlet C

g
□ Flameproof Packing Adaptor f
Ø21.7 (Code : /PG2)
Approx. 231

Approx. 95

100 150±1

Model and Code A B C D E a b c d e f g h Weight

PH8HFF-PP-J10-T-□□-JS 125 90 14 19 - 80 9 11 60 25 30 70 Approx. 250 Approx. 3.2kg
PH8HFF-S3-J10-T-□□-JS 125 90 14 19 - 70 10 6 60.5 26 26 69 Approx. 245 Approx. 7.6kg
PH8HFF-PP-A15-T-□□-JS 108 79.4 14.2 15.7 - 80 9 11 60 25 30 70 Approx. 250 Approx. 3.2kg
PH8HFF-S3-A15-T--□□-JS 108 79.2 14.2 15.7 2 70 10 6 60.5 26 26 69 Approx. 245 Approx. 7.6kg

□ Mounting Bracket (Option Code : /MF1) Weight : Approx. 0.5 kg

Bracket (Thickness : 3)

Mounting holes for holder

26 6-Ø10 holes

75 75
140

70±0.3
45 45
10

70±0.3
92
Approx. 82
2B(O.D. 60.5) Pipe
Approx. 130 Holes Dimension for Wall Mounting

Figure 1.4 Flow-Through Type Holder (with Fameproof type Ultrasonic Cleaner)

IM 12B07N01-01E
 < 1. Specifications > 1-13
5. Solenoid Valve UNIT: mm

General Purpose Solenoid Valve Explosionproof Solenoid Valve

PH8MV*D PH8MVF*B
95
70 64
103
72 46

102

146.5
14.5
71 2-Rc1/2 G1/2

14
90 2-Rc1/2 G1/2

Cautions on Installation of Solenoid Valve for Jet / Brush Cleaning

1. Do not allow a sample solution to flow backward into the solenoid valve or to be replaced with the driving fluid.
For this take relevant measures; e.g. install a check valve to prevent inverse pressure between the inlet and outlet of the solenoid
valve, or install the solenoid valve higher than the holder, especially when using the air jet/brush cleaning system.
2. Make sure to avoid the risk of corrosion of the solenoid body (bronze) and seal (nitrilel rubber) by vapor or gaseous components
generated from a sample solution, especially when using the air jet/brush cleaning system.

F1.5.ai

Figure 1.5 Solenoid Valve for Jet & Brush Cleaning

IM 12B07N01-01E
Blank Page
 < 2. Installation, Piping and Wiring > 2-1

2. Installation, Piping and Wiring

2.1 Holder Installation

2.1.1 Installation Site
Install the flow-through type holder in a site where the holder can be easily maintained.

2.1.2 Mounting the Flow-through Type Holder

When strong piping - e.g. process piping - is next to the holder, mount the holder on it as shown
in Figure 2.1.
When a polypropylene holder is used, be careful not to apply excessive force to it.
Outlet Outlet

Inlet Inlet

F2.1E.ai

Figure 2.1 Support by Process Piping

If the process piping is not strong enough to mount the holder, use mounting hardware (available
as option) to mount the holder on a vertical (or horizontal) pipe with sufficient strength as
shown in Figure 2.2. The holder can be mounted on a bracket as shown in Figure 2.3 (remove
unnecessary parts from the metal fittings).
Sensor Mounting Nut

Flow-Through
Type Holder Stanchion

F2.2E.ai

Figure 2.2 Pipe Mounting

IM 12B07N01-01E
2-2 < 2. Installation, Piping and Wiring >

Sensor Mounting Nut

Flow-Through Type Holder

Bracket

70 mm

2-M6

F2.3E.ai

Figure 2.3 Bracket Mounting

2.2 Process Piping

Piping (through which the process fluid flows) connected to the holder: The process piping should
be installed as per specifications, and the temperature, pressure and flow rate of process fluid
conforms to the specifications of the sensor and holder to be used. When a holder with jet or
brush cleaning is used, the piping should be installed accordingly. You should also keep “ease of
maintenance” and “calibration with standard solution” in mind when installing the piping.

2.2.1 Main Precautions for Piping

(1) When a holder with jet or brush cleaning is used:
The cleaning fluid (water or air) is at higher pressure than the process fluid. If you want to
prevent water or air flowing up line, a check valve should be provided as shown in Figure
2.4.

Note
For safety’s sake you should confirm that it is safe for the cleaning fluid to flow into the down-line
piping.

Flow Outlet

Check Valve

Flow Inlet

Jet or Brush Cleaning

F2.4E.ai

Figure 2.4 Check Valve Installation

IM 12B07N01-01E
 < 2. Installation, Piping and Wiring > 2-3
(2) When a polypropylene holder is used:
Keep the temperature and pressure of the process fluid (pressure of the cleaning fluid for
holders with jet or brush cleaning) within the range shown in Figure 2.5.
105
100

Stainless Steel
80

60
(°C)
40
Temperature

20 Polypropylene
(or Stainless Steel)
0 100 200 300 400 500
Pressure (kPa)
F2.5E.ai

Figure 2.5 Temperature and Pressure Diagram for Polypropylene Resin Holder

(3) When a general use sensor with KCl, solution tank is used:
The pressure of the process fluid inside the holder should not exceed the tank head
pressure 10 kPa (0.1 kg/cm2G).
General Type Reserve Tank

Ht > Hm
KCl Head Pressure Ht

Solution Head Pressure Hm

At Least 1 m

KCl Filling
Type Sensor

Inlet

F2.6E.ai

Figure 2.6 Relationship between the Solution Pressure, Pressure and Reserve Tank Height

IM 12B07N01-01E
2-4 < 2. Installation, Piping and Wiring >

(4) When a sensor with medium pressure KCl, solution tank is used:
Provide stop valves in the up-line and down-line piping adjacent to the holder.

Stop Valve

Stop Valve
F2.7E.ai

Figure 2.7 Stop Valve Installation

2.2.2 Piping Procedure

Piping Materials:
Use the materials shown below for the process piping adjacent to the flow-through type holder.
• Hard polyvinylchloride pipe Nominal diameter 25 mm
• Polypropylene pipe Nominal diameter 25 mm
• Wire rainforced soft polyvinylchloride pipe Nominal diameter 25 mm
• Stainless steel pipe (JIS G3459)
SUS304 or SUS316 Nominal diameter 25 mm
Piping Example:
1. The outlet tube should be as short as possible to expel 2. When a horizontal outlet tubing is long,
the solution to atmosphere. a vertical tube (H) should also be long.

Flowmeter Flowmeter

F2.8E.ai

Figure 2.8 Sensor with General Type Reserve Tank

IM 12B07N01-01E
 < 2. Installation, Piping and Wiring > 2-5
1. Install stop valves upstream and downstream of the 2. Install a check valve before the flow-through holder
flow-through holder to allow ease of maintenance. as necessary.

Process Piping
Solenoid
Valve
Stop Valve

Check Stop
Valve Valve
Stop
Flowmeter
Valve

Stop Valve Cleaning Piping

Drain Piping

F2.9E.ai

Figure 2.9 When the Solution has a Pressure

Flow-Through Holder

Drain Pan

F2.10E.ai

Figure 2.10 Cleaning the Flow-Through Holder

2.3 Installing the Sensor

Refer to the separate manual describing the sensor to be used.

2.4 Cleaner Piping

This section applies only to the submersion type holder with cleaner.

2.4.1 Piping Precautions

(1) Provide a slight slack in a flexible tubing between the cleaner and a mating device to allow
ease of maintenance.
(2) Determine the cleaner pipe size to allow sufficient flow and pressure. Use nominal 15
mm pipe for air cleaning piping. If the water/jet cleaner pipe or water/brush cleaner pipe is
subject to freezing temperature during winter, cover it with a suitable insulation material.
(3) Use a normally-open (opens when relay is energized) nominal 15 mm diameter solenoid
valve for the cleaning line. The solenoid valve supplied by Yokogawa meets the following
specifications.

IM 12B07N01-01E
2-6 < 2. Installation, Piping and Wiring >

[Model PH8MV Solenoid Valve]

Pilot kick operated, 2-port valve. Open when energized.
Fluid: Normal tap water, industrial water, or air.
Operating Pressure: 0 to 1 MPa
Forward (reverse) Pressure Resistance: 2 MPa
Fluid Temperature: Water; 5 to 60°C, Air; -10 to 60°C
Cv: 4.5
Process Connection: Rc 1/2
Power Supply: 100/110/200/220 V AC, 50/60 Hz
Power Consumption: 10 W
Construction: IP53
Material: Body; Bronze
Sealing; Nitrile rubber
Ambient Temperature: Maximum 50°C
Cable Inlet Connection: G 1/2
Weight: Approx. 0.9 kg

[Model PH8MVF Explosionproof Solenoid Valve]

Pilot kick operated, 2-port valve. Open when energized.
Fluid: Normal tap water, industrial water, or air.
Operating Pressure: 0.05 to 1 MPa
Forward (reverse) Pressure Resistance: 1.5 MPa
Fluid Temperature: Water; 5 to 60°C, Air; -10 to 60°C
Cv: 4.5
Process Connection: Rc 1/2
Power Supply: 100V AC, 50/60 Hz., 110V AC, 60 Hz
200V AC, 50/60 Hz., 220V AC, 60 Hz
Power Consumption: 10 W
Construction: TIIS flameproof (for d2G4 gas).
Material: Body; Bronze
Seal; Nitrile rubber
Ambient Temperature: Maximum 50°C
Valve Seat Leakage: 300 Nml/min. (At air pressure 50 to 700 kPa )
Cable Inlet Connection: G 1/2 (Frameproof packing adaptor)
Mounting Position: Vertical mounting with coil in top
Weight: Approx. 1.9 kg

IM 12B07N01-01E
 < 2. Installation, Piping and Wiring > 2-7

2.4.2 Piping Procedure

(1) Air piping examples
Drive Signal
To Wash Cycle Timer

Solenoid Valve*1
Regulator
Supply Air

Nominal 15 mm Pressure 200 kPa (2 kg/cm2)

Hard Pipe Minimum
Nominal 16 mm Wire-Reinforced Vinyl Tube*2

Notes:
*1 If corrosive gas is produced at the measuring site, consider
using a corrosion-resistant solenoid valve.
*2 If the solution temperature is high, use a high temperature
resistant solenoid valve.
F2.11E.ai

Figure 2.11 Typical Brush/jet Cleaner Air Piping

(2) Industrial water piping examples

Drive Signal
To Wash Cycle Timer
Solenoid Valve

Industrial Water

Pressure 200 kPa (2 kg/cm2)

Minimum
Nominal 15 mm Hard Pipe
Ball
Valve
Nominal 16 mm Wire- Reinforced Vinyl Tube
F2.12E.ai

Figure 2.12 Industrial Water Piping for Typical Brush/Jet Cleaner

(3) Tap water piping examples

Drive Signal
* To Wash Cycle Timer

Tap Water
Float Valve

Nominal 16 mm
Wire-Reinforced
Vinyl Tube

Pump
Cleaning
Water Tank
Check Drain
Valve

Note:
*: When using a Model PH8PU1 cleaner pump and tank, set the solution
pressure to 10 kPa (0.1 kg/cm2) or below. F2.13E.ai

Figure 2.13 Tap Water Piping for Typical Brush/Jet Cleaner

IM 12B07N01-01E
2-8 < 2. Installation, Piping and Wiring >

2.4.3 Installation of PH8PU1 Washer Pump and Water Tank

The PH8PU1 Washer Pump and Tank are used to provide water jet and brush cleaning in
drinking water applications. For details, refer to the separate IM 19C1E1-01E on PH8PU1
Washer Pump and Tank.

2.5 Wiring
This section describes the wiring between the ultrasonic oscillator and cleaner, and between
the solenoid valve, pump, and PH201G distributor. For the sensor wiring, refer to the chapter
describing the sensor.

2.5.1 Ultrasonic Oscillator Circuit Wiring

For the non-explosionproof ultrasonic oscillator, connect the cable from the cleaner directly to the
terminals inside the PUS400G Ultrasonic Oscillator.

For details of PUS400G, refer to the separate IM 19C1B3-01E.

For the explosionproof ultrasonic oscillator, connect the cable from the cleaner directly to the
terminals inside the PH8USF Ultrasonic Oscillator and PH8AL Alarm Box.

For detailsof PH8USF, PH8AL, refer to the separate IM 12B5U2-E.

2.5.2 Solenoid Valve Circuit Wiring

This is the wiring for the water jet or brush cleaning.
The wash timer in the Intelligent pH transmitter outputs a contact signal via the PH201G
Distributor. You should wire this contact to operate the solenoid valve. If you are using the
PH8PU1 Washer Pump and Tank, then the wiring is described in Sec. 2.5.3.

PH201G Distributor

Washing contact
Solenoid Valve Signal Terminals

General-purpose Explosionproof
Solenoid Valve Solenoid Valve
Power supply
F2.14E.ai

Figure 2.14 Wiring the Solenoid Valve Circuit

IM 12B07N01-01E
 < 2. Installation, Piping and Wiring > 2-9
[Non-explosionproof solenoid valve]
Use a 2-conductor vinyl-sheathed cable with an outer diameter of 10 to 12 mm for the wiring.
[Explosionproof solenoid valve]
When the PH8MVF explosionproof solenoid valve is used, use tapped (screw-in) explosionproof
conduit for wiring.

2.5.3 Wiring for PH8PU1 Washer Pump and Tank

Figure 2.15 shows the internal and external wiring for the PH8PU1 Washer Pump and Tank.
For 100 V AC wiring
Terminal Box

Spark Killer Solenoid Actuator U1

U2
X Pump
1 3 5 13 A
V1
M
V2
Y E
G
2 4 6 14 B
96 98

Terminal box in field

2 6 95 6 2G

For 200 V AC wiring

V2
U2
Y Pump
V1
M
U1
A1 A2 L1 L2 G
X E
G

Terminal box in field

Ground

Distributor "wash" Pump Power

contact signal F2.15E.ai

Figure 2.15 Internal and external wiring for the PH8PU1 Washer Pump and Tank

As shown in the figure, connect terminals "A1" and "L1" from the PH201G distributor to terminals
A1 and L1 in the terminal box, and connect the power supply to operate the pump between
terminals L1 and L2. Also connect together terminals A2 and L2 as shown in the figure. Be sure
to ground the ground terminal G.

IM 12B07N01-01E
Blank Page
 < 3. Maintenance/Inspection > 3-1

3. Maintenance/Inspection

3.1 Cleaning the Holder

When process fluid contains slurry which tends to settle in the holder regularly so that the slurry
does not build up. Remove the plug or cleaning element on the holder bottom to clean the holder.

Plug or Cleaning Element

Nut

F3.1E.ai

Figure 3.1 Plug and Nut

3.1.1 Inspecting the O-ring Seal

The O-ring seal used in the wetted part of the flow-through type holder is made of fluorocarbon
rubber, which has superior resistance to corrosion - suitable for use with most process fluids.
Usually, therefore, no periodic inspection is necessary. When a flow-through holder with
ultrasonic cleaner is used, if the process fluid enters the ultrasonic cleaner, parts replacement
may be required to repair it. Inspect the O-ring seal when checking or repairing the ultrasonic
cleaner.
To prevent trouble, replace the O-ring seal periodically - e.g. every two years.

Ultrasonic Vibrator

O-ring

Note: This ultrasonic cleaning element is non-explosionproof type.

F3.2E.ai

Figure 3.2 Ultrasonic Cleaner O-ring

IM 12B07N01-01E
3-2 < 3. Maintenance/Inspection >

3.2 Checking the Cleaning Element

This section applies to the flow-through type holder with cleaning element. Check the cleaning
element to maintain the flow-through type holder in good operating condition.

3.2.1 Jet Cleaning Element

If the cleaner does not clean the sensor electrode, check if the sensor nozzles are clogged. Use a
0.8 mm diameter wire to remove any material clogging the sensor nozzles.

F3.3E.ai

Figure 3.3 Cleaning the Nozzle Holes

3.2.2 Cleaning the Brush

If the electrode becomes dirty, the brush may be excessively worn. When the brush is worn out,
replace it. Insert a screwdriver into the cleaner hole to prevent the rotor from turning, and then
turn the brush assembly counterclockwise. The brush can be easily removed from the rotor. See
Figure 3.4. When mounting a new brush, reverse the disassembly procedure.
Brush Cleaning Loosen
Element

To prevent the rotor turning,

insert a screwdriver into the
hole, then turn the brush
assembly.

F3.4E.ai

Figure 3.4 Disassembling the Brush

IM 12B07N01-01E
 < 3. Maintenance/Inspection > 3-3

3.2.3 Ultrasonic Cleaning Element

For several weeks after starting the operation, check the ultrasonic cleaning element for
corrosion. If corroded, replace it with the type most suitable for the measurement solution,
selecting from among the element materials: SUS316 stainless steel, titanium and Hastelloy C.
If a corroded element is not replaced, the solution may enter the ultrasonic element and cause
problems. If this occurs, replace the cleaning element immediately.
[Non-explosionproof ultrasonic cleaning element]
(1) To remove a defective ultrasonic cleaning element, unscrew the cleaning element mounting
screw, so the cleaning element holder can be removed from the screw connector. Move
the cleaning element out until the connector appears, and disconnect the vibrator leadwire
connector from the holder side connector. See Figure 3.5.

F3.5E.ai

Figure 3.5 Non-Explosionproof Cleaning Element

(2) Check that there is no corrosion around the O-ring sealed surface. It is recommended that
the O-ring be replaced whenever the element cleaned.
(3) Mounting a new ultrasonic cleaning element. After attaching the connector, rotate the
cleaning element two to three turns and store the cable inside the holder. Secure the
cleaning element mounting screw. Check the cleaning element material by the marking
on the surface of the vibrator element; H for Hastelloy, T for titanium, none for SUS316
stainless steel.
Ultrasonic Cleaning Element

Cleaning Element Mounting Nuts

O-Ring

F3.6E.ai

Figure 3.6 Non-Explosionproof Ultrasonic Cleaning Element

IM 12B07N01-01E
3-4 < 3. Maintenance/Inspection >

[Replace the explosionproof cleaning element]

For replacing the ultrasonic cleaning element, consults with Yokogawa service personnel.

3.2.4 Maintenance of PH8PU1 Washer Pump and Tank

For details, refer to the separate IM 19C1E1-01E.

IM 12B07N01-01E
Customer Model PH8HF, PH8HFF
Maintenance Flow-Through type Holders
Parts List

PH8HF Non-Explosionproof Type

2
3

6 4 5
7

Item Part No. Qty Description

1 ─ 1 O-Ring
K9142QW Fluoro rubber (FKM)
K9319RG for /PF option
2 K9143KM 1 Brush
3 K9143KA 1 Brush Assembly (for brush cleaning)

4 K9143JN 1 Nozzle (for jet cleaning)

5 ─ 1 Vibrator Assembly (for ultrasonic cleaning)
K9143QA Transducer: Stainless Steel
K9143QB Transducer: Titanium
K9143QC Transducer: Hastelloy C

6 ─ 1 O-Ring
K9142QT Fluoro rubber (FKM) for Ultrasonic Cleaning
K9319RD /PF option for Ultrasonic Cleaning
K9142QU Fluoro rubber (FKM) for Jet or Brush Cleaning
K9319RS /PF for Jet or Brush Cleaning

7 ─ 1 O-Ring
K9142QX Fluoro rubber (FKM)
K9319RH for /PF option

All Rights Reserved. Copyright © 1982 Yokogawa Electric Corporation. CMPL 12B05N01-01E
Subject to change without notice. 1st Edition: Nov. 1982 (YK)
4th Edition: Jun. 2016 (YK)
2

PH8HFF Explosionproof Type

Item Part No. Qty Description

1 ─ 1 O-Ring
K9142QW Fluoro rubber (FKM)
K9319RG for /PF option
2 ─ 1 O-Ring
K9142QX Fluoro rubber (FKM)

K9319RH for /PF option

Stainless Steel Mounting Bracket (Option code: /MF1)

Set part No: K9145LD for option code /MF1

4th Edition: Jun. 2016 (YK) CMPL 12B05N01-01E

 i

Revision Information
 Title : Model PH8HF, PH8HFF Flow-Through Type Holder
 Manual No. : IM 12B07N01-01E

Nov. 2018/6th Edition

Added FLXA402 (page i)

Jul. 2016/5th Edition

List of related items: Deletion HA405, HA406, DPA405, DPA406, HF405; Page 1-1 Applicable sensors
of PH8HF Flow-through Type Holder: Deletion special pH/ORP sensor; CMPL 12B05N01-01E revised
to 4th edition (all revision of P/N).

Nov. 2015/4th Edition

Revision by the version up of GS.; page-i ♦ INTRODUCTION “2. Contents“ Add PH4,OR4 and
FLXA202. Delete PH400G, PH100 and PH8PU1; page 1-11 Some revision of solenoid valve of
PH8MV and PH8MVF; Page 2-6 Some revision of Specification of PH8MV and PH8MVF; Some revi-
sion of page 5 on CMPL 12B07N01-01E 3rd edition (P/N deletion for explosion-proof type).

Oct. 2011/3rd Edition Page layout changed by InDesign

p.1-1, Some addition of Caution on use, and correction of jet cleaning unit material; p.3-4 to p.3-7
Deletion of procedure for [Replace the explosionproof cleaning element].

Dec. 2005/2nd Edition

Some error correction.

Oct. 2004/1st Edition

Newly published.

IM 12B07N01-01E
Blank Page