TECHNICAL BULLETIN
NO: LTB00338 (ISSUE 1)
02 MAR 2011
SERVICE PARTS WARRANTY BODY SHOP
CIRCULATE TO:
9 9 9
THIS BULLETIN REPLACES LTB00253 (ALL ISSUES)
SECTION: 307
‘Transmission Fault’ Displayed / DTC P0826-62 Stored
AFFECTED VEHICLE RANGE:
LR4 (LA) VIN: AA510742 – AA526446
Model Year: 2010
Range Rover Sport (LS) VIN: AA212147 – AA232569
Model Year: 2010
CONDITION SUMMARY:
Situation: Transmission Fault’ may be displayed in the instrument cluster message center. Diagnostic
Trouble Code (DTC) P0826-62 may be stored in the Transmission control module (TCM) and the shift paddles
may be inoperative. This may be caused when the TCM receives a Sport / Manual signal with the
transmission shift lever in the Park (P) position, usually occurring at ignition ‘ON’ or during engine cranking.
Action: In the event of a customer concern of the above, refer to the Repair Procedure outlined below to
update the TCM software.
PARTS:
No parts necessary
TOOLS:
IDS with latest IDS-DVD and Calibration File; first available on IDS-DVD123_V7.08 Calibration File 56
Land Rover-Approved Midtronics Vehicle Power Supply
Refer to Workshop Manual for any required special tools
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to DDW to obtain the latest repair
time.
DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a
quantity of zero.
DESCRIPTION SRO TIME CONDITION CAUSAL PART
(HOURS) CODE
Update TCM software – LR4 44.90.07 0.30 42 LR013863
Update TCM software – Range Rover Sport 44.90.07 0.30 42 LR016316
Normal Warranty policies and procedures apply
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and
equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are
not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Land Rover service facility to
determine whether this bulletin applies to a specific vehicle.
©2011 Jaguar Land Rover North America LLC Page 1
NO: LTB00338 (ISSUE 1)
02 MAR 2011 TECHNICAL BULLETIN
REPAIR PROCEDURE
UPDATE THE TRANSMISSION CONTROL MODULE SOFTWARE
CAUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these
steps may cause damage to control modules in the vehicle.
CAUTION: A Land Rover-approved Midtronics Vehicle Power Supply must be connected to the
vehicle battery during IDS diagnosis / module programming.
1. Connect the Land Rover-approved Midtronics Vehicle Power Supply to the vehicle battery.
2. Turn ignition 'ON' (engine not running).
NOTE: IDS must be loaded with IDS-DVD123_V7.08 or later and Calibration File 56 or later.
3. Connect the IDS to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.
4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.
5. From the Session Type selection screen, choose 'Diagnosis'.
6. Select the 'Selected Symptoms' tab, and then select one of the following:
x Powertrain > Automatic transmission and transaxle > Automatic transmission and transaxle symptoms >
Paddle shift malfunction > Inoperative
OR
x Electrical > Instruments > Information and message centre > Message display area > Powertrain
7. Select 'continue'.
8. Select the 'Recommendations' tab.
NOTE: The option to configure the Transmission control module will only appear on the
Recommendations tab if DTC P0826-62 is currently stored.
9. From the Recommendations tab, select 'Run' to configure the 'Transmission control module'
x Follow all on-screen instructions to complete this task.
10. Exit the current session.
11. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.
Page 2 of 2
