Instruction Manual EDR and ETR Valves

D100391X012 April 2011

Fisherr EDR and ETR easy‐et Valves

Contents Figure 1. Reverse Acting easy‐e Valve with Actuator
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Trim Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Packing Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 8
Parts Ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Packing Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Parts Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

W2080‐1

Introduction
Scope of Manual
This instruction manual includes installation, maintenance, and parts information for NPS 1 through 4 EDR and ETR
valves (see figure 1). The valves are available in CL150 through 600 ratings.
The valves are also available with full‐size and restricted‐trim designs. Refer to separate manuals for instructions
covering the actuator and accessories.
Do not install, operate, or maintain an EDR or ETR valve without being fully trained and qualified in valve, actuator, and
accessory installation, operation, and maintenance. To avoid personal injury or property damage, it is important to
carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings. If you
have any questions about these instructions, contact your Emerson Process Management sales office before
proceeding.

Description
The EDR and ETR are single‐port, globe‐style valves that feature cage guiding, a balanced plug design, and
push‐down‐to‐open valve plug action. The valve constructions are available with metal‐to‐metal or
metal‐to‐composition seats. These constructions permit access to the internal trim parts through the bottom flange
without removing the actuator from the valve.

www.Fisher.com
EDR and ETR Valves Instruction Manual
April 2011 D100391X012

Table 1. Specifications
Available Valve Constructions Shutoff Classification
EDR: ANSI/FCI 70‐2 and IEC 60534‐4 Class II
See table 2
(standard); Class III for valves with a graphite piston
ring and 78 mm (3.4375 inch) or larger port diameter
ETR: Standard air test
End Connection Styles
(0.05 mL/minute/psid/inch of port diameter) using
Cast Iron Valves air at service pressure drop or 3.5 bar (50 psi),
Flanged: CL125 flat‐face or 250 raised‐face flanges per whichever is lower; or ANSI/FCI 70‐2 and
ASME B16.1 IEC 60534‐4 Class V (optional) with PTFE seats; Class
Steel and Stainless Steel Valves IV or V (optional) with metal seats
Flanged: CL150, 300, and 600 raised‐face or ring‐type
joint flanges per ASME B16.5 Flow Characteristics
Screwed or Socket Welding: All available ASME B16.11 Linear (all cages), quick‐opening, or equal percentage
schedules that are consistent with CL600 per ASME
B16.34 Flow Directions
Buttwelding: Consistent with ASME B16.25 Linear, Quick Opening, or Equal Percentage Cage:
Normally up,
Whisper Trimt I Cage: Always down
Maximum Inlet Pressure(1)
Approximate Weights
Cast Iron Valves
Flanged: Consistent with CL125B or 250B VALVE SIZE, WEIGHT
pressure‐temperature ratings per ASME B16.1 NPS kg Pounds
Steel and Stainless Steel Valves 1 & 1‐1/4 14 30
1‐1/2 20 45
Flanged: Consistent with CL150, 300, and 600(2)
2 39 67
pressure‐temperature ratings per ASME B16.34 2‐1/2 45 100
Screwed or Welding: Consistent with CL600 3 54 125
pressure‐temperature ratings per ASME B16.34 4 77 170

1. The pressure/temperature limits in this manual and any applicable standard or code limitation for the valve should not be exceeded.
2. Certain bonnet bolting material selections may require a CL600 easy‐e valve assembly to be derated. Contact your Emerson Process Management sales office.

Table 2. Available Valve Constructions

VALVE MATERIAL AND END CONNECTION STYLE
VALVE Carbon Steel, Alloy Steel, or Stainless Steel Valve Cast Iron Valve
VALVE
SIZE,
DESIGN RF or RTJ Flanged Butt‐ Socket CL125B CL250B
NPS Screwed
CL150 CL300 CL600 welding Weld FF Flanged RF Flanged
1, 1‐1/2, or 2 X X X X X X X X
EDR 1‐1/4 X ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐
2‐1/2, 3, or 4 ‐‐‐ X X X X ‐‐‐ X X
1, 1‐1/2, or 2 X X X X X X ‐‐‐ ‐‐‐
ETR 1‐1/4 X ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐
2‐1/2, 3, or 4 ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐ ‐‐‐
X = Available Construction

2
Instruction Manual EDR and ETR Valves
D100391X012 April 2011

Figure 2. Actuator Mounting

CAP SCREWS

STEM CONNECTOR
INDICATOR SCALE

INDICATOR DISK
ACTUATOR YOKE

STEM LOCKNUTS PACKING FLANGE NUTS

YOKE LOCKNUT
BONNET

W2080‐1

Installation
WARNING
Always wear protective gloves, clothing, and eyewear when performing any installation operations.
To avoid personal injury or property damage resulting from the sudden release of pressure, do not install the valve
assembly where service conditions could exceed the limits given on the valve and actuator nameplates. Use
pressure‐relieving devices as required by accepted industry, local, state, or Federal codes, and good engineering practices.
Check with your process or safety engineer for any other hazards that may be present from exposure to process media.
If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in this
instruction manual.

CAUTION
The valve configuration and construction materials were selected to meet particular pressure, temperature, pressure drop,
and controlled fluid conditions. Because some body/trim material combinations are limited in their pressure drop and
temperature range capabilities, do not exceed these conditions without first contacting your Emerson Process
Management sales office.
Inspect the valve and pipelines to ensure they are not damaged, are clean, and free of foreign material.

3
EDR and ETR Valves Instruction Manual
April 2011 D100391X012

1. Before installing the valve, inspect the valve and associated equipment for any damage and any foreign material.
2. Make certain the valve body interior is clean, that pipelines are free of foreign material, and that the valve is
oriented so that pipeline flow is in the same direction as the arrow (see figure 2) on the side of the valve.
3. The control valve assembly can be installed in any orientation unless limited by seismic criteria. However, the
normal method is with the actuator vertical above the valve body (see figure 2). Other positions may result in
uneven valve plug and cage wear, and improper operation. With some valves, the actuator may also need to be
supported when it is not vertical. For more information, consult your Emerson Process Management sales office.
4. Use accepted piping and welding practices when installing the valve in the line. If a post‐weld heat treatment
process is to be applied to the valve end connections, and the valve has composition or elastomer trim parts,
remove the trim to avoid damage to the soft parts.

CAUTION

Depending on valve body materials used, post weld heat treating may be required. If so, damage to internal elastomeric
and plastic parts, as well as internal metal parts is possible. Shrunk‐fit pieces and threaded connections may loosen. In
general, if post weld heat treating is to be performed, all trim parts should be removed. Contact your Emerson Process
Management sales office for additional information.

5. If continuous operation is required during inspection or maintenance, install a three‐valve bypass around the
control valve assembly.
6. If the actuator and valve are shipped separately, refer to the actuator mounting procedure in the appropriate
actuator instruction manual and also see figure 2.

WARNING
Personal injury could result from packing leakage. Valve packing was tightened prior to shipment; however some
readjustment will be required to meet specific service conditions.

Maintenance
WARNING
Avoid personal injury from sudden release of process pressure. Before performing any maintenance operations:
D Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personal
injury.
D Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure the
actuator cannot suddenly open or close the valve.
D Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressure
on both sides of the valve. Drain the process media from both sides of the valve.
D Vent the power actuator loading pressure and relieve any actuator spring precompression.
D Use lock‐out procedures to be sure that the above measures stay in effect while you work on the equipment.
D The valve packing box may contain process fluids that are pressurized, even when the valve has been removed from the
pipeline. Process fluids may spray out under pressure when removing the packing hardware or packing rings, or when
loosening the packing box pipe plug.

4
Instruction Manual EDR and ETR Valves
D100391X012 April 2011

D Check with your process or safety engineer for any additional measures that must be taken to protect against process
media.

Valve parts are subject to normal wear and must be inspected and replaced as necessary. Inspection and maintenance
frequency depends on the severity of service conditions. This section includes instructions for trim maintenance,
packing maintenance, and packing lubrication. All maintenance operations may be performed with the valve installed
in the pipeline.

Note
If the valve has ENVIRO‐SEALt live‐loaded packing installed (figure 8, 9, or 10), see the Fisher instruction manual entitled
ENVIRO‐SEAL Packing System for Sliding‐Stem Valves for packing instructions.

Trim Maintenance
Disassembly

Note
Whenever a gasket seal is disturbed by removing or shifting gasketed parts, install a new gasket upon reassembly. This is necessary
to ensure a good gasket seal.

Key number locations are shown in figure 11 or 12 unless otherwise indicated.

Figure 3. Valve Plug Assembly

STEM
DISK SEAT

DISK

VALVE PLUG

CAGE

CASTLE NUT
40A5479‐B
B2360
COTTER PIN

NOTE:
ETR OR EDR
1 ETR USES A SEAL RING (KEY 24) AND A BACKUP RING (KEY 25) (SEE FIGURE 11).

5
EDR and ETR Valves Instruction Manual
April 2011 D100391X012

CAUTION

Take care when removing the bottom flange (key 31) in the following procedure, to prevent possible product damage from
parts unexpectedly falling out of the valve body.

1. Isolate the control valve from the line pressure, release pressure from both sides of the valve body, and drain the
process media from both sides of the valve. If using a power actuator, also shut off all pressure lines to the power
actuator, release all pressure from the actuator. Use lock‐out procedures to be sure that the above measures stay in
effect while you work on the equipment. When removing the bottom flange (key 31), be careful that the cage and
other parts are not damaged by unexpectedly falling out of the valve body. Remove the nuts (key 16) or cap screws
from the bottom flange.
2. Removing the valve plug from the valve body, the valve plug can be removed independently of the valve stem by
removing the cotter pin and castle nut (keys 30 and 8). Then, slide the valve plug out of the cage (see figure 3).
D Disconnect the stem connector, and loosen the packing flange nuts (see figure 2).

D Move the valve stem away from the actuator stem allowing room to remove the indicator disk and stem locknuts.
Remove the parts indicated.

D Remove the valve plug by pulling the valve plug/stem assembly through the packing and out of the bottom of the
bonnet.

D If the valve plug is to be re‐used but the stem needs to be replaced, drive the pin (key 8) out of the plug/stem
assembly and unscrew the valve stem.

CAUTION

Take care during disassembly in the following procedure, to prevent possible damage to sealing surfaces.

3. Remove the seat ring (key 9), gaskets (keys 10, 11, 12, and 13), and any remaining parts if they did not come out
with the valve plug. If the seat ring (key 9) is stuck in the valve body, strike the outside of the valve body at the seat
ring line with a rubber hammer while pulling down on the seat ring. Carefully remove the seat ring without
damaging sealing surfaces.
If necessary, machine or grind metal seats before installing the piston ring/seal ring or packing, or refer to the Lapping
Metal Seats procedure in this section.

Lapping Metal Seats

A certain amount of leakage should be expected with metal‐to‐metal seating in any valve body. If the leakage
becomes excessive, however, the condition of the seating surfaces of the valve plug and seat ring can be improved by
lapping. (Deep nicks should be machined out rather than ground out.) Use a good quality lapping compound of a
mixture of 280 to 600‐grit.

Assemble the valve to the extent that the seat ring (key 9), cage (key 3), cage adaptor (key 4, if used), and bonnet are
in place. Also, remove the piston ring or seal ring from the valve plug (if used).
1. Insert the valve stem (key 7) into the bonnet and thread the plug (key 2) onto the end of the stem. Make a simple
handle from a piece of strap iron; lock it to the valve with the stem locknuts.

6
Instruction Manual EDR and ETR Valves
D100391X012 April 2011

2. Apply the lapping compound to the seating surfaces. Rotate the handle alternately in each direction to lap the
seats. After lapping the seats, remove the valve plug and stem, then clean all parts. Repeat the lapping procedure if
necessary.

Trim Assembly
Carefully clean all gasket surfaces. Use new gaskets during reassembly of the valve.

Table 3. Valve Body‐to‐Flange Nut Torques(3)

VALVE TORQUES(1)
SIZE, SA193‐B7 SA193‐B8M(2)
NPS NSm LbfSft NSm LbfSft
1 and 1‐1/4 129 95 64 47
1‐1/2, 1‐1/2 x 1, 2, or 2 x 1 96 71 45 33
2‐1/2, 2‐1/2 x 1‐1/2, or 3 x 1‐1/2 129 95 64 47
3, 3 x 2, 3 x 2‐1/2, or 4 x 2 169 125 88 65
4, 4 x 2‐1/2, or 4 x 3 271 200 156 115
1. Determined from laboratory tests.
2. SA193‐B8M annealed.
3. For other materials, contact your Emerson Process Management sales office.

Replacing the Seal or Piston Ring

CAUTION

Be careful not to scratch the surface of the ring groove in the valve plug (key 2), or the new ring may not seal properly.

D For EDR, if the piston ring (key 6) is visibly damaged, remove the ring and replace it with a new part. Refer to the
Parts List at the end of this manual for a replacement part.

D For ETR, if the seal ring and backup ring (keys 24 and 25) are visibly damaged, remove the rings by prying or cutting
them from the groove. Be careful not to scratch valve plug surfaces. Refer to the Parts List at the end of this manual
for replacement parts.

Assembling the Valve Plug and Stem

1. For EDR and ETR, perform the following steps:
D Insert the stem (key 7) into the plug (key 2, figure 3) and thread the castle nut (key 8) onto the end of the stem and
hand tighten.

CAUTION

To prevent possible product damage, take care that the stem and plug are not damaged during the following tightening
procedure.

D When tightening the castle nut with a wrench, line up the hole in the end of the stem with a slot in the castle nut.
Ensure that the stem and plug are not damaged during the tightening procedure.

D Insert the cotter pin (key 30) and lock it in place.

7
EDR and ETR Valves Instruction Manual
April 2011 D100391X012

Installing the Piston Rings or Backup Ring/Seal Rings

1. For EDR: When using a carbon‐filled PTFE piston ring, spread the ring apart slightly at the split, start one end of the
split into the groove in the valve plug. Work the ring around the valve plug inserting the ring into the groove in the
valve plug.
The replacement graphite piston rings will arrive in one piece. Use a vise with smooth or tapered jaws to break the
replacement piston ring into two halves. Place the new ring in the vise so that the jaws compress the ring into an oval.
Compress the ring slowly until the ring snaps on both sides. If one side snaps first, do not try to tear or cut the other
side. Instead, keep compressing the ring until the other side snaps. The piston ring can also be fractured by scoring
and snapping over a hard surface such as a table edge. Sawing or cutting the ring is not recommended.
2. For ETR: Apply a lubricant to both backup and seal rings (keys 25 and 24). Place the backup ring over the stem (key
7) and into the groove in the valve plug (key 3). Slowly and gently stretch the seal ring over the valve plug and work
it into the groove. Stretching the ring over the valve plug can cause it to appear too large for the groove, but it will
contract to its original size when inserted into the cage.

CAUTION
When installing the EDR or ETR valve plug into the cage, make sure the piston or seal ring is evenly engaged in the entrance
chamfer of the cage to avoid damage to the ring.

Note
Use the preceding procedures to assemble the valve plug and stem before installing the parts into the valve body. Insert the valve
plug into the cage (figure 3), then stack the parts as recommended in steps below.

Installing the Parts into the Valve Body

1. Stack the valve trim parts using figures 11 and 12 to determine the sequence of parts.
2. Lubricate the stud bolts (key 15) before installing the valve trim into the valve body. (Note: For ease of installing
trim parts, remove all packing parts from the packing box before installing the trim parts.)
3. When inserting the stack of trim parts into the valve body, carefully align the parts in the recess of the valve body.
4. Slide the bottom flange onto the stud bolts (key 15). Secure the bottom flange (key 31) in place on the valve body
with the hex nuts (key 16). Tighten the hex nuts to the torque value shown in table 3.
5. Torque the nuts in a criss‐cross pattern. Repeat the pattern until all nuts are torqued to the value indicated in table
3.
6. Refer to the Packing Maintenance procedures below.

Packing Maintenance
This procedure covers PTFE V‐ring, graphite ribbon/filament, and PTFE composition packing rings. Key numbers refer
to figure 5 for PTFE V‐ring packing and PTFE/composition packing, unless otherwise indicated.

Note
If the valve has ENVIRO‐SEAL live‐loaded packing installed (figure 8, 9, or 10), see the Fisher instruction manual entitled
ENVIRO‐SEAL Packing System for Sliding‐Stem Valves for packing instructions.

8
Instruction Manual EDR and ETR Valves
D100391X012 April 2011

For all except spring‐loaded packing, if the packing is relatively new and tight on the stem, and if tightening the
packing flange nuts does not stop the leakage, it is possible that the valve stem is worn or nicked so that a seal cannot
be made. If the leakage comes from the outside diameter of the packing follower, it is possible that the leakage is
caused by nicks or scratches around the inside of the packing box wall.

For spring‐loaded single PTFE V‐ring packing, the spring (key 8) maintains a sealing force on the packing. If leakage is
noted around the packing follower (key 13), check to be sure the shoulder on the packing follower is touching the
bonnet. If the shoulder is not touching the bonnet, tighten the packing flange nuts (key 5, figure 4) until the shoulder
is against the bonnet. If leakage cannot be stopped in this manner, proceed to the Removing Packing and Installing
Packing procedures below.

Removing Packing

WARNING
Refer to the WARNING at the beginning of the Maintenance section in this instruction manual.

The packing may have been removed in earlier steps, or during trim maintenance procedures. Use the following steps,
when necessary, to remove packing and associated assemblies.

Key number locations for packing parts are shown in figures 5 and 6. For valve parts and the live loaded packing
system, refer to figures 8 through 10 (in the Parts List section), for key number locations.
1. Isolate the control valve from the line pressure, release pressure from both sides of the valve body, and drain the
process media from both sides of the valve. If using a power actuator, also shut off all pressure lines to the power
actuator and release all pressure from the actuator. Use lock‐out procedures to be sure that the above measures
stay in effect while you work on the equipment.
2. Exhaust all actuator pressure, disconnect the operating lines from the actuator, and disconnect any leakoff piping
from the actuator. Relieve any actuator precompression from the stem connector. (If necessary, refer to the
appropriate actuator instruction manual for warnings, cautions, and disassembly procedures.)
3. When removing the bottom flange (key 31), be careful that the cage and other parts are not damaged by
unexpectedly falling out of the valve body. Remove the nuts (key 16) or cap screws from the bottom flange.
4. To remove the packing for maintenance, disconnect the stem connector (see figure 2). Remove the yoke locknut,
and lift the actuator off the valve.
5. Remove the packing flange nuts (key 5, figure 4), packing flange (key 15), upper wiper (key 12), and packing
follower (key 13). If maintaining the packing while the valve stem is in place, ensure that the valve stem surface is
not scratched or marred while working with the packing.

Table 4. Recommended Torque for Packing Flange Nuts

VALVE STEM GRAPHITE PACKING PTFE PACKING
DIAMETER PRESSURE
Minimum Torque Maximum Torque Minimum Torque Maximum Torque
RATING
mm Inches NSm LbfSin NSm LbfSin NSm LbfSin NSm LbfSin
CL125, 150 3 24 5 48 1 12 3 24
9.5 3/8 CL250, 300 4 36 7 60 2 18 3 30
CL600 5 48 8 72 3 24 4 36
CL125, 150 5 48 8 72 3 24 4 36
12.7 1/2 CL250, 300 7 60 10 84 3 30 5 42
CL600 10 84 14 120 5 42 7 60
CL125, 150 11 96 16 144 5 48 8 72
19.1 3/4 CL250, 300 14 120 20 180 7 60 10 90
CL600 20 180 30 264 10 90 15 132

9
EDR and ETR Valves Instruction Manual
April 2011 D100391X012

Figure 4. Bonnet Assembly

PACKING
10A6681‐A
BOX 1

NOTE:
1 REFER TO FIGURE 5 OR 6 FOR PACKING ARRANGEMENTS.

CAUTION
To prevent possible product damage, avoid scratching the packing box walls when removing old packing parts. Also
inspect valve stem threads and packing box surfaces for sharp edges which may damage packing.

6. Avoid scratching the packing box walls when removing the old packing parts. Clean the packing box (see figure 4),
and clean, inspect, or replace metal packing parts. Generally, the metal packing parts are not part of the packing
kits listed in the Parts List section, and they must be ordered individually.
7. Inspect the valve stem threads and packing box surfaces for any sharp edges which might cut the packing.
Scratches or burrs on the stem surfaces can cause packing box leakage or damage to new packing. If the surface
condition cannot be improved by light sanding, replace the damaged parts by following the appropriate steps in
the Trim Maintenance procedure.

Note
If the control valve assembly was purchased for an application where the service temperatures are under 232_C (450_F), the
bonnet may be unscrewed from the valve body. Where temperatures are greater than 232_C (450_F), the bonnet is seal welded to
the valve body.

CAUTION
To prevent possible product damage, set the bonnet on a protective surface in the following procedure.

8. If necessary, remove the bonnet assembly from the valve by unscrewing it. Some applications require seal welding
the bonnet to the valve body, and the bonnet should not be removed. Set the bonnet on a protective surface to
prevent damage to the bonnet gasket surface.

10
Instruction Manual EDR and ETR Valves
D100391X012 April 2011

Figure 5. Packing Arrangements

UPPER WIPER UPPER WIPER
(KEY 12) (KEY 12)
PACKING
FOLLOWER PACKING
(KEY 13) FEMALE FOLLOWER
ADAPTOR 2 FEMALE (KEY 13)
2 ADAPTOR
PACKING RING 2
MALE 2 PACKING RING
ADAPTOR 2 MALE
WASHER 2 ADAPTOR SPACER (KEY 8) 1
(KEY 10)
SPRING
(KEY 8)

PACKING BOX
RING (KEY 11)
PACKING BOX
RING (KEY 11)
LOWER WIPER 2 2 LOWER WIPER
FOR S31600 (316 SST) OR S17400 (17‐4PH) FOR ALL OTHER METAL PACKING
SST METAL PACKING BOX PARTS BOX PART MATERIALS
NOTES:
1 REFER TO THE VALVE SERIAL NUMBER AND THE PARTS ORDERING
SECTION FOR THE SPACER AND OTHER METAL PARTS.
2 PACKING SET (KEY 6) (2 REQ'D FOR DOUBLE ARRANGEMENTS).
12A7837‐A
B2358‐1
TYPICAL SINGLE ARRANGEMENTS

UPPER WIPER
(KEY 12)
PACKING
FOLLOWER
(KEY 13)
MALE
ADAPTOR
PACKING RING
FEMALE
ADAPTOR
LANTERN RING
(KEY 8)

PACKING BOX
RING (KEY 11)
12A8187-C 12A7814-C 12A7839-A
ASSEMBLY 1 ASSEMBLY 2 ASSEMBLY 3 ASSEMBLY 1 ASSEMBLY 2 ASSEMBLY 3 ASSEMBLY 1 ASSEMBLY 2 ASSEMBLY 3
(POSITIVE (VACUUM) (POSITIVE (POSITIVE (VACUUM) (POSITIVE (POSITIVE (VACUUM) (POSITIVE LOWER WIPER
PRESSURES) PRESSURES PRESSURES) PRESSURES PRESSURES) PRESSURES
& VACUUM) & VACUUM) & VACUUM)

9.5mm (3/8 INCH) STEM 12.7 mm (1/2 INCH) STEM 19.1 mm (3/4 INCH) STEM
B2359 TYPICAL DOUBLE ARRANGEMENTS

11
EDR and ETR Valves Instruction Manual
April 2011 D100391X012

Figure 6. Packing Arrangements

UPPER WIPER (KEY 12)

PACKING FOLLOWER (KEY 13)

PACKING RING (KEY 7)

LANTERN RING (KEY 8)

PACKING BOX RING (KEY 11)

9.5 mm 12.7 mm 19.1 mm

12A8188‐A
12A7815‐A (3/8 INCH) (1/2 INCH) (3/4 INCH)
12A8173‐A
A2619‐3 STEM STEM STEM

TYPICAL (DOUBLE) ARRANGEMENTS

DETAIL OF PTFE/COMPOSITION PACKING

PACKING FOLLOWER (KEY 13)

GRAPHITE RIBBON PACKING RING (KEY 7)

1 1
GRAPHITE FILAMENT PACKING RING (KEY 7)
1

LANTERN RING (KEY 8)

PACKING BOX RING (KEY 11)
14A3411-A 13A9775-B 13A9776-B

9.5 mm 12.7 mm 19.1 mm

(3/8 INCH) (1/2 INCH) (3/4 INCH)
STEM STEM STEM

SINGLE ARRANGEMENTS
PACKING FOLLOWER (KEY 13)

GRAPHITE RIBBON PACKING RING (KEY 7)

1 1
GRAPHITE FILAMENT PACKING RING (KEY 7)
1

1 LANTERN RING (KEY 8)

PACKING BOX RING (KEY 11)
14A2153-B 14A1849-B 14A1780-B

9.5 mm 12.7 mm 19.1 mm

(3/8 INCH) (1/2 INCH) (3/4 INCH)
STEM STEM STEM
1 NOTE:
0.102 mm (0.004 INCH) THICK SACRIFICIAL DOUBLE ARRANGEMENTS
ZINC WASHERS; USE ONLY ONE BELOW

A5864
EACH GRAPHITE RIBBON RING. DETAIL OF GRAPHITE RIBBON/ FILAMENT PACKING

12
Instruction Manual EDR and ETR Valves
D100391X012 April 2011

Installing Packing
If the trim is removed, refer to Trim Maintenance procedures, and install the trim (including the valve stem) before
installing the packing. If necessary, use the Lapping Metal Seats procedures before installing packing. Key number
locations are shown in figure 5 or 6 unless otherwise indicated.

CAUTION

To prevent possible product damage, take care when installing the bonnet over the valve stem in the following procedure.

1. If the bonnet has been removed from the valve body, install the replacement bonnet (see figure 4). Carefully slide
the bonnet over the valve stem without damaging the stem surfaces.
2. Refer to figure 5 or 6 for the sequence of parts to make up the appropriate packing set for your application. Arrange
the packing parts in sequence before installing them into the packing box.
3. For split‐ring packing, alternate the positions of the splits to avoid creating a leak path. Place a smooth‐edged pipe
over the valve stem and gently tap each soft packing ring into the packing box. Be sure that air is not trapped
between adjacent soft parts.
4. Install the packing follower (key 13), packing flange (key 3), and upper wiper (key 12, if required). Install the
packing flange nuts (key 5).
5. Refer to actuator installation procedures in the actuator instruction manual, and the installation procedures in the
manual when mounting and connecting the actuator to the valve. If lubrication is required, refer to the Packing
Lubrication section below.
6. For spring‐loaded PTFE V‐ring packing, tighten the packing flange nuts until the shoulder on the packing follower
(key 13, figure 4) contacts the bonnet.
For graphite packing, tighten the packing flange nuts to the maximum recommended torque shown in table 4. Then,
loosen the packing flange nuts, and retighten them to the recommended minimum torque shown in table 4.

For other packing types, tighten the packing flange nuts alternately in small equal increments until one of the nuts
reaches the minimum recommended torque shown in table 4. Then, tighten the remaining flange nuts until the
packing flange is level and at a 90‐degree angle to the valve stem.

Note
If the valve has ENVIRO‐SEAL live‐loaded packing installed (figure 8, 9, or 10), see the Fisher instruction manual entitled
ENVIRO‐SEAL Packing System for Sliding‐Stem Valves for packing instructions.

Packing Lubrication

WARNING
To avoid personal injury or property damage resulting from fire or explosion, do not lubricate packing used in oxygen
service or in processes with temperatures over 260_C (500_F).

13
EDR and ETR Valves Instruction Manual
April 2011 D100391X012

Packing used in oxygen service or in processes with temperatures over 260_C (500_F) should not be lubricated. If a
lubricator or lubricator/isolating valve (see figure 7) is required for the packing, install the lubricator or
lubricator/isolating valve into the threaded hole in the side of the bonnet (see figure 7). Use a good quality silicon‐base
lubricant.

To operate the lubricator, simply turn the cap screw clockwise to force the lubricant into the packing box. The
lubricator/isolating valve operates the same way except the isolating valve must first be opened and then closed after
lubrication is completed.

Figure 7. Lubricator and Lubricator/Isolating Valve

LUBRICATOR

10A9421‐A
AJ5428‐D
A0832‐2
LUBRICATOR/ISOLATING VALVE

Parts Ordering
Each body‐bonnet assembly is assigned a serial number which can be found on the valve body. This same number also
appears on the actuator nameplate when the valve is shipped from the factory as part of a control valve assembly.
Refer to the serial number when contacting your Emerson Process Management sales office for technical assistance.
When ordering replacement parts, refer to the serial number and to the eleven‐character part number for each part
required from the following parts kit or parts list information.

WARNING
Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Process Management should not,
under any circumstances, be used in any Fisher valve, because they may void your warranty, might adversely affect the
performance of the valve, and could cause personal injury and property damage.

Note
Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use, or
maintenance of any product. Responsibility for the selection, use, and maintenance of any product remains with the purchaser and
end user.

14
Instruction Manual EDR and ETR Valves
D100391X012 April 2011

Packing Kits
Standard Packing Repair Kits (Non Live‐Loaded)
Standard Packing Repair Kits (non live‐loaded)
Stem Diameter, mm (Inches) 9.5 (3/8) 12.7 (1/2) 19.1 (3/4)
Yoke Boss Diameter, mm (Inches) 54 (2‐1/8) 71 (2‐13/16) 90 (3‐9/16)
PTFE (Contains keys 6, 8, 10, 11, and 12) RPACKX00012 RPACKX00022 RPACKX00032
Double PTFE (Contains keys 6, 8, 11, 12) RPACKX00042 RPACKX00052 RPACKX00062
PTFE/Composition (Contains keys 7, 8, 11, and 12) RPACKX00072 RPACKX00082 RPACKX00092
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring], 8, and 11) RPACKX00102 RPACKX00112 RPACKX00122
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring]) RPACKX00132 RPACKX00142 RPACKX00152
Double Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring], 8, and 11) RPACKX00162 RPACKX00172 RPACKX00182

ENVIRO‐SEAL Packing Retrofit Kits

Retrofit kits include parts to convert valves with existing standard bonnets to the ENVIRO‐SEAL packing box
construction. Refer to figure 8 for key numbers for PTFE packing, to figure 9 for key numbers for graphite packing, and
to figure 10 for key numbers for duplex packing. PTFE kits include keys 200, 201, 211, 212, 214, 215, 216, 217, 218,
tag, and cable tie. Graphite kits include keys 200, 201, 207, 208, 209, 210, 211, 212, 214, 217, tag, and cable tie.
Duplex kits include keys 200, 201, 207, 209, 211, 212, 214, 215, 216, 217, tag, and cable tie.
Stems and packing box constructions that do not meet Fisher stem finish specifications, dimensional tolerances, and
design specifications, may adversely alter the performance of this packing kit.
For part numbers of individual components in the ENVIRO‐SEAL packing kits, refer to instruction manual ENVIRO‐SEAL
Packing System for Sliding‐Stem Valves, D101642X012.
ENVIRO‐SEAL Packing Retrofit Kits
STEM DIAMETER AND YOKE BOSS DIAMETER, mm (INCH)
PACKING
9.5 (3/8) 12.7 (1/2) 19.1 (3/4)
MATERIAL
54 (2‐1/8) 71 (2‐13/16) 90 (3‐9/16)
Double PTFE RPACKXRT012 RPACKXRT022 RPACKXRT032
Graphite ULF RPACKXRT262 RPACKXRT272 RPACKXRT282
Duplex RPACKXRT212 RPACKXRT222 RPACKXRT232

ENVIRO‐SEAL Packing Repair Kits

Repair kits include parts to replace the “soft” packing materials in valves that already have ENVIRO‐SEAL packing
arrangements installed or in valves that have been upgraded with ENVIRO‐SEAL retrofit kits. Refer to figure 8 for key
numbers for PTFE packing, to figure 9 for key numbers for graphite packing, and to figure 10 for key numbers for
duplex packing. PTFE repair kits include keys 214, 215, and 218. Graphite repair kits include keys 207, 208, 209, 210,
and 214. Duplex repair kits include keys 207, 209, 214, and 215.
Stems and packing box constructions that do not meet Fisher stem finish specifications, dimensional tolerances, and
design specifications, may adversely alter the performance of this packing kit.
For part numbers of individual components in the ENVIRO‐SEAL packing kits, refer to instruction manual ENVIRO‐SEAL
Packing System for Sliding‐Stem Valves, D101642X012.
ENVIRO‐SEAL Packing Repair Kits
Stem Diameter, mm (Inches) 9.5 (3/8) 12.7 (1/2) 19.1 (3/4)
Yoke Boss Diameter, mm (Inches) 54 (2‐1/8) 71 (2‐13/16) 90 (3‐9/16)
Double PTFE (contains keys 214, 215, & 218) RPACKX00192 RPACKX00202 RPACKX00212
Graphite ULF (contains keys 207, 208, 209, 210, and 214) RPACKX00592 RPACKX00602 RPACKX00612
Duplex (contains keys 207, 209, 214, and 215) RPACKX00292 RPACKX00302 RPACKX00312

15
EDR and ETR Valves Instruction Manual
April 2011 D100391X012

Figure 8. Typical ENVIRO‐SEAL Packing System Figure 9. Typical ENVIRO‐SEAL Packing System
with PTFE Packing with Graphite ULF Packing

STUD
(KEY 200)

HEX NUT SPRING

(KEY 212) PACK
ASSEMBLY
(KEY 217)
PACKING
FLANGE GUIDE
(KEY 201) BUSHING
(KEY 207)
PACKING
PACKING WASHERS
RING (KEY 214)
(KEY 209)

PACKING
RING GUIDE
(KEY 210) BUSHING
(KEY 208)
PACKING
BOX RING
(KEY 211)

A6297‐1
39B4612/A

Figure 10. Typical ENVIRO‐SEAL Packing System with Duplex Packing

213
200

212

201

217

207
215

216

207 207

214
209

211
207

24B9310‐A
A6722

16
Instruction Manual EDR and ETR Valves
D100391X012 April 2011

Parts Kits

Note
Kits do not apply to alloy C (N10276 & CW2M), Alloy 20 (N08020 & CN7M), or alloy 400 (N04400 & M35‐1) trims.

Kits for full‐ and restricted‐ capacity trims with service temperature to 593_C (1100_F) include S31600 [316 stainless
steel (SST)] shim and N06600/graphite spiral wound gasket.

Gasket Kits and Shims(1)

Valve Size, NPS Key Number To 593_C (To 1100_F) Valve Size, NPS Key Number To 593_C (To 1100_F)
Set RGASKETX162
Set RGASKETX262
10 1R2859X0042
1 or 1‐1/4 12 1R286099442 10 1R3847X0032
11 1R3100X0032
13 1R2862X0062
32 16A1936X012 2‐1/2 x 1‐1/2 12 1R309999442
13 1R3098X0052
14 1R3844X0052
Set RGASKETX172 32 16A1937X012
10 1R3101X0032
1‐1/2 12 1R309999442
13 1R3098X0052
32 16A1937X012 Set RGASKETX202
10 1R3484X0042
3 12 1R348299442
Set RGASKETX242 13 1R3481X0052
10 1R3101X0032 32 16A1940X012
11 1R2861X0042
1‐1/2 x 1 12 1R286099442
13 1R3098X0052 Set RGASKETX272
20 1U2152X0042 10 1R3484X0042
32 16A1936X012 11 1R3298X0032
3x2 12 1R329799442
13 1R3296X0042
Set RGASKETX182 14 1R3481X0052
10 1R3299X0042 32 16A1938X012
2 12 1R329799442
13 1R3296X0042
32 16A1938X012 Set RGASKETX212
10 1R3724X0042
Set RGASKETX252 4 12 1R372299442
10 1R3299X0042 13 1J5047X0062
11 1R2861X0042 32 16A1941X012
2x1 12 1R286099442
13 1R2862X0062
14 1R3296X0042 Set RGASKETX282
32 16A1936X012 10 1R3724X0042
11 1R3846X0042
Set RGASKETX192
4 x 2‐1/2 12 1R384599442
10 1R3847X0032
2‐1/2 13 1R3844X0052
12 1R384599442
14 1J5047X0062
13 1R3844X0052
32 16A1939X012
32 16A1939X012
1. The bonnet gasket (key 10), spiral gasket (key 12), seat gasket (key 13), adapter gasket (key 14), adapter gasket (key 20) and shim (key 32) are included in gasket kit (RGASKET).

Gasket Descriptions
MATERIAL
KEY NUMBER DESCRIPTION
FGM -198_ to 593_C (-325_ to 1100_F)
10 Bonnet Gasket
11 Cage Gasket
Graphite/S31600
13 Seat Ring or Liner Gasket
14 or 20 Adapter Gasket
12 Spiral‐Wound Gasket N06600/Graphite
32 Shim S31600

17
EDR and ETR Valves Instruction Manual
April 2011 D100391X012

Parts List Valve Assembly

(figures 11 and 12)
Key Description Part Number

Note   1 Valve Body

 If you need a valve body as a replacement part, order by valve
Part numbers are shown for recommended spares only. For part size, serial number, and desired material.
numbers not shown, contact your Emerson Process Management sales   2* Valve plug See following table
office.   3* Cage See following table
  4 Cage adaptor
  5 Seat Ring Adaptor
  6* Piston Ring See following table
  7* Valve Stem See following table
  8* Castle Nut (standard), SST
 For EDR and ETR only
  9.5 mm (3/8 inch) O.D. stem with
   9.5 mm (3/8 inch) VSC(1) and

Bonnet Assembly (figure 4)    12.7 mm (1/2 inch) O.D. stem

   with 9.5 mm (3/8 inch) VSC 1E5034X0012
  12.7 mm (1/2 inch) O.D. stem
   with 12.7 mm (1/2 inch) VSC and
   19.1 mm (3/4 inch) O.D. stem
   with 12.7 mm (1/2 inch) VSC 1J141235072
Note   9* Seat Ring See following table
For ENVIRO‐SEAL packing box parts, see instruction manual  10* Bonnet Gasket See following table
ENVIRO‐SEAL Packing System for Sliding‐Stem Valves, D101642X012.  11* Cage Gasket See following table
 12* Spiral‐Wound Gasket See following table
 13* Seat Ring or Liner Gasket See following table
 14*
  or
 20* Adapter Gasket See following table
 15 Cap Screw or Stud Bolt
Key Description Part Number
 16 Hex Nut
 17 Pipe plug for tapped bottom flanges
  1 Bonnet  18 Flow Arrow
 If you need a bonnet as a replacement part, order by valve  19 Drive screw
  size and stem diameter, serial number, and desired material.  21* Disk retainer, S31600
  3 Packing flange  For ETR only
  4 Packing flange stud   NPS 1, 1‐1/4 or 2 x 1 valve 1V710035072
  5 Packing flange nut   NPS 1‐1/2 valve 1V710335072
  6* Packing Set, Single PTFE V‐ring, (2 req'd)   NPS 1‐1/2 x 1 valve 1V712135072
For 9.5 mm (3/8 inch) stem 1R290001012   NPS 1‐1/2 or 2‐1/2 x 1‐1/2 valve 1V710335072
For 12.7 mm (1/2 inch) stem 1R290201012   NPS 2 or 3 x 2 valve 1V710835072
For 19.1 mm (3/4 inch) stem 1R290401012   NPS 2‐1/2 or 4 x 2‐1/2 valve 1V710935072
  7* Packing ring See key 5, Set   NPS 3 valve 1V711235072
  8 Spring   NPS 4 valve 1V711533092
  8 Lantern ring  22* Disk Seat
  8 Spacer   For ETR only
 Please refer to the valve serial number and the Parts Ordering    Use w/soft seat, 1,
section for the spacer and packing replacement parts     NPS 1‐1/4, or 2 x 1 restricted trim
information.     S31600 1V710235072
 11* Packing Box ring, S31600 (standard)     R30006 (alloy 6) 1V710239102
 9.5 mm (3/8 inch) stem 1J873135072    NPS 1‐1/2 x 1 restricted trim
 12.7 mm (1/2 inch) stem 1J873235072     S31600 1V712235072
 19.1 mm (3/4 inch) stem 1J873335072     R30006 1V712239102
 14 Pipe plug    NPS 1‐1/2 or 2‐1/2 x 1‐1/2 valve
 14 Optional lubricator     S31600 1V710535072
 14 Optional lubricator/isolating valve     R30006 1V710539102
 15 Yoke Locknut    NPS 2 or 3 x 2 valve
 27 Pipe nipple for optional lubricator/isolating valve     S31600 1V710635072
 30* Lower Wiper, PTFE See key 6, Set     R30006 1V710639102
 31* Male Adapter, PTFE See key 6, Set    NPS 2‐1/2 or 4 x 2‐1/2 valve
 32* Female Adaptor, PTFE See key 6, Set     S31600 1V711135072
    R30006 1V711139102

18 *Recommended spare parts

Instruction Manual EDR and ETR Valves
D100391X012 April 2011

Key Description Part Number Key Description Part Number

   NPS 3 valve    NPS 3 valve 1V659705092

    S31600 1V711435072    NPS 4 valve 1V659905092
    R30006 1V711439102  25* Backup ring
   NPS 4 valve   For ETR only
    CF8M 1V711733092    NPS 1, 1‐1/4, 1‐1/2 x 1, or
    R30006 1V711739102     2 x 1 valve
 23* Disk      Nitrile 1V659003052
 Use with composition seats only      Fluorocarbon 1V659005292
  NPS 1, 1‐1/4, 1‐1/2 x 1 or 2 x 1 valve      Ethylene‐propylene 1V6590X0042
   PTFE 1V710106242    NPS 1‐1/2, or 2‐1/2 x 1‐1/2 valve
   Nylon 1V710103152      Nitrile 1V659203052
  NPS 1‐1/2, or 2‐1/2 x 1‐1/2 valve      Fluorocarbon 1V659205292
   PTFE 1V710406242      Ethylene‐propylene 1V6592X0032
   Nylon 1V710403152    NPS 2 or 3 x 2 valve
  NPS 2 or 3 x 2 valve      Nitrile 1V550703052
   PTFE 1V710706242      Fluorocarbon 1V550705292
   Nylon 1V710703152      Ethylene‐propylene 1V5507X0042
  NPS 2‐1/2 or 4 x 2‐1/2 valve    NPS 2‐1/2 or 4 x 2‐1/2 valve
   PTFE 1V711006242      Nitrile 1V659403052
   Nylon 1V711003152      Fluorocarbon 1V659405292
  NPS 3 valve      Ethylene‐propylene 1V6594X0032
   PTFE 1V711306242    NPS 3 valve
   Nylon 1V711303152      Nitrile 1V659603052
  NPS 4 valve      Fluorocarbon 1V659605292
   PTFE 1V711606242      Ethylene‐propylene 1V6596X0032
   Nylon 1V711603152    NPS 4 valve
 24* Seal ring, carbon filled PTFE      Nitrile 1V659803052
  For ETR only      Fluorocarbon 1V659805292
   NPS 1, 1‐1/4, 1‐1/2 x 1, or      Ethylene‐propylene 1V6598X0022
    2 x 1 valve 1V659105092  30 Cotter pin
   NPS 1‐1/2, or 2‐1/2 x 1‐1/2 valve 1V653905092  31 Bottom Flange
   NPS 2 or 3 x 2 valve 1V550805092  32* Shim See following table
   NPS 2‐1/2 or 4 x 2‐1/2 valve 1V659505092  33 Nameplate

Key 2* Valve Plug for EDR and ETR Valves

VALVE ORIFICE STEM S41600 S31600/ S31600/ HI TEMPERATURE
SIZE DIAMETER S31600
SIZE, (416 SST) CoCr‐A CoCr‐A S31600/CoCr‐A
(316 SST)
NPS mm Inches mm Inches STANDARD SEAT SEAT & GUIDE SEAT & GUIDE
1, 1‐1/4
33 1.3125 9.5 3/8 20A6125X012 20A6125X022 20A6126X012 20A6127X012 21A2891X012
1‐1/2 x 1, 2 x 1
1‐1/2 &
48 1.875 9.5 3/8 20A6128X012 20A6128X022 20A6129X012 20A6130X012 21A2892X012
2‐1/2 x 1‐1/2
2&3x2 59 2.3125 12.7 1/2 20A6131X012 20A6131X022 20A6132X012 20A6133X012 21A2893X012
2‐1/2 &
73 2.875 12.7 1/2 20A6134X012 20A6134X022 20A6135X012 20A6136X012 21A2894X012
4 x 2‐1/2
3 87 3.4375 12.7 1/2 20A6137X012 20A6137X022 20A6138X012 20A6139X012 21A2895X012
4 111 4.375 12.7 1/2 20A6140X012 20A6140X022 20A6141X012 20A6142X012 21A2896X012

*Recommended spare parts 19

EDR and ETR Valves Instruction Manual
April 2011 D100391X012

Key 3* Cage
CB7Cu‐1
CF8M CF8M, Alloy 6
Cage Style Hardened
(316 SST) Nickel Coated (Cast)
(17‐4 HT)
Valve Sizes NPS 1, 1‐1/4, 1‐1/2 x 1, and 2 x 1
Equal Percentage 2U215333272 2U215333092 2U740848932 2U215339102
Linear 2U215633272 2U215633092 2U741448932 2U215639102
Quick Opening 2U215033272 2U215033092 2U740348932 2U215039102
Whisper I 2V502333272 ‐‐‐ 2V503048932 ‐‐‐
Valve Sizes NPS 1‐1/2 and 2‐1/2 x 1‐1/2
Equal Percentage 2U219533272 2U219533092 2U740948932 2U219539102
Linear 2U219833272 2U219833092 2U741548932 2U219839102
Quick Opening 2U219233272 2U219233092 2U725448932 2U219239102
Whisper I 2V502433272 ‐‐‐ 2V503148932 ‐‐‐
Valve Sizes NPS 2 and 3 x 2
Equal Percentage 2U223733272 2U223733092 2U741048932 2U223739102
Linear 2U224033272 2U224033092 2U741648932 2U224039102
Quick Opening 2U223433272 2U223433092 2U740448932 2U223439102
Whisper I 2V502533272 ‐‐‐ 2U503248932 ‐‐‐
Valve Sizes NPS 2‐1/2 and 4 x 2‐1/2
Equal Percentage 2U227933272 2U227933092 2U741148932 2U227939102
Linear 2U228233272 2U228233092 2U741748932 2U228239102
Quick Opening 2U227633272 2U227633092 2U740548932 2U227639102
Whisper I 2V502633272 ‐‐‐ 2V503348932 ‐‐‐
Valve Size NPS 3
Equal Percentage 2U232133272 2U232133092 2U741248932 2U232139102
Linear 2U232433272 2U232433092 2U741848932 2U232439102
Quick Opening 2U231833272 2U231833092 2U740648932 2U231839102
Whisper I 2V502733272 ‐‐‐ 2V503448932 ‐‐‐
Valve Size NPS 4
Equal Percentage 2U236333272 2U236333092 2U741348932 2U236339102
Linear 2U236633272 2U236633092 2U741948932 2U236639102
Quick Opening 2U236033272 2U236033092 2U740748932 2U236039102
Whisper I 23A8915X032 ‐‐‐ 2V503548932 ‐‐‐

Key 6* Piston Ring (EDR only)

GRAPHITE
VALVE SIZE, NPS
Oxidizing Service
1, 1‐1/4, 1‐1/2 x 1, 2 x 1 1U2174X0012
1‐1/2, 2‐1/2 x 1‐1/2 1U2216X0012
2, 3 x 2 1U2258X0012
2‐1/2, 4 x 2‐1/2 1U2300X0012
3 1U2342X0012
4 1U2392X0012

Group 1 Actuators by Type Number

54 mm (2‐1/8 inches),
71 mm (2‐13/16 inches),
or 90 mm (3‐9/16 inches) Yoke Boss
585C Series—50.8 mm (2 inches) maximum travel
585C
1B
644 & 645
655
657 & 667—76.2 mm (3 inches) maximum travel
1008—71.4 mm (2‐13/16 inches) yoke boss

20 *Recommended spare parts

Instruction Manual EDR and ETR Valves
D100391X012 April 2011

Key 7* Valve Stem, S31600 (316 Stainless Steel) for EDR and ETR Valves
GROUP 1 ACTUATOR(1)
Stem
Stem
Valve Size, Travel Connection Part
Diameter
NPS Diameter Number
mm Inches mm Inches mm Inches
Valves with Full Size Trim
1& 9.5 3/8 9.5 3/8 22A3121X012
7 to 19 0.25 to 0.75
1‐1/4 12.7 1/2 12.7 1/2 22A3122X012
9.5 3/8 9.5 3/8 20A6492X012
1‐1/2 7 to 19 0.25 to 0.75
12.7 1/2 9.5 3/8 20A6496X012
7 to 19 0.25 to 0.75 12.7 1/2 12.7 1/2 22A3123X012
2 29 1.125 12.7 1/2 12.7 1/2 20A6493X012
7 to 29 0.25 to 1.125 19.1 3/4 12.7 1/2 20A6499X012
7 to 19 0.25 to 0.75 12.7 1/2 12.7 1/2 22A3124X012
29 to 38 1.125 to 1.5 12.7 1/2 12.7 1/2 20A6494X012
2‐1/2
7 to 29 0.25 to 1.125 19.1 3/4 12.7 1/2 22A3127X012
38 1.5 19.1 3/4 12.7 1/2 20A6500X012
7 to 19 0.25 to 0.75 12.7 1/2 12.7 1/2 21A4298X012
29 to 38 1.125 to 1.5 12.7 1/2 12.7 1/2 20A6494X012
3
7 to 29 0.25 to 1.125 19.1 3/4 12.7 1/2 22A3128X012
38 1.5 19.1 3/4 12.7 1/2 20A6500X012
7 to 19 0.25 to 0.75 12.7 1/2 12.7 1/2 21A5097X012
29 to 38 1.125 to 1.5 12.7 1/2 12.7 1/2 22A3126X012
4 51 2 12.7 1/2 12.7 1/2 20A6495X012
7 to 29 0.25 to 1.125 19.1 3/4 12.7 1/2 22A3129X012
38 to 51 1.5 to 2 19.1 3/4 12.7 1/2 20A6501X012
Valves with Restricted Trim
1‐1/2 x 1 7 to 19 0.25 to 0.75 9.5 3/8 9.5 3/8 20A6492X012
2x1 7 to 19 0.25 to 0.75 12.7 1/2 9.5 3/8 27A2091X012
2‐1/2 x 1‐1/2 7 to 19 0.25 to 0.75 12.7 1/2 9.5 3/8 27A2092X012
7 to 19 0.25 to 0.75 12.7 1/2 12.7 1/2 27A2093X012
3x2
29 1.125 12.7 1/2 12.7 1/2 27A2094X012
7 to 19 0.25 to 0.75 12.7 1/2 12.7 1/2 22A3126X012
4 x 2‐1/2
29 to 38 1.125 to 1.5 12.7 1/2 12.7 1/2 20A6495X012
1. For Group 1 actuators by type number, see following table.

Key 9* Seat Ring (for metal seat only)

S41600 (416 SST) S31600 S31600/CoCr‐A
Valve Size, NPS
Hardened (316 SST) Seat
1, 1‐1/4 & 2 x 1 1U222546172 1U222535072 1U222539102
1‐1/2 & 2‐1/2 x 1‐1/2 1U221946172 1U221935072 1U221939102
1‐1/2 x 1 1U222046172 1U222035072 1U222039102
2&3x2 1U222646172 1U222635072 1U222639102
2‐1/2 & 4 x 2‐1/2 1U222746172 1U222735072 1U222739102
3 1U222846172 1U222835072 1U222839102
4 1U222946172 1U222933092 1U222939102

*Recommended spare parts 21

EDR and ETR Valves Instruction Manual
April 2011 D100391X012

Figure 11. EDR and ETR with Full‐Size Trim Valve Assembly

FLOW DIRECTION
WHISPER TRIM
STANDARD TRIM

40A5480‐D

22
Instruction Manual EDR and ETR Valves
D100391X012 April 2011

Figure 12. EDR and ETR with Restricted Trim Valve Assembly

FLOW DIRECTION
40A5482‐D WHISPER TRIM
STANDARD TRIM

23
EDR and ETR Valves Instruction Manual
April 2011 D100391X012

Fisher, easy-e, ENVIRO-SEAL, and Whisper Trim are marks owned by one of the companies in the Emerson Process Management business division of
Emerson Electric Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other
marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not
to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales
are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of
such products at any time without notice. Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the
selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser
and end user.
Emerson Process Management
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Chatham, Kent ME4 4QZ UK
Dubai, United Arab Emirates
Singapore 128461 Singapore

www.Fisher.com

24
EFisher Controls International LLC 1992, 2011; All Rights Reserved