OMS, OMT

and OMV
Orbital Motors

Technical
Information
 OMS, OMT and OMV
Technical Information
A Wide Range of Orbital Motors

Revision History Table of Revisions

Date Page Changed Rev
Nov 2009 67 conversions, and layout adjusted ED
Nov 2010 68 Dimensions changed EF
Jul 2012 57 Typo in ‘Major dia’ EG
Nov 2012 3 Planetary Gears deleted EH
Jan 2013 20 Correct drawing EI
Apr 2013 16 Drawing corrected EJ
Jun 2013 54 Drawing corrected EK

F300 540., F300 030

A Wide Range of Orbital Sauer-Danfoss is a world leader within production of low speed orbital motors with
Motors high torque. We can offer more than 1600 different orbital motors, categorised in types,
variants and sizes (incl. different shaft versions).
The motors vary in size (rated displacement) from 8 cm3 [0.50 in3] to 800 cm3 [48.9 in3]
per revolution.
Speeds range up to approx. 2500 min-1 (rpm) for the smallest type and up to approx
600 min-1 (rpm) for the largest type.
Maximum operating torques vary from 13 Nm [115 lbf·in] to 2700 Nm [24.000 lbf·in]
(peak) and maximum outputs are from 2.0 kW [2.7 hp] to 70 kW [95 hp].

Characteristic features:
•• Smooth running over the entire speed range
•• Constant operating torque over a wide speed range
•• High starting torque
•• High return pressure without the use of drain line (High pressure shaft seal)
•• High efficiency
•• Long life under extreme operating conditions
•• Robust and compact design
•• High radial and axial bearing capacity
•• For applications in both open and closed loop hydraulic systems
•• Suitable for a wide variety of hydraulics fluids

© 2013 Sauer-Danfoss. All rights reserved.

Sauer-Danfoss accepts no responsibility for possible errors in catalogs, brochures and other printed material.
Sauer -Danfoss reserves the right to alter its products without prior notice. This also applies to products
already ordered provided that such alterations can be made without affecting agreed specifications. All
trademarks in this material are properties of their respective owners. Sauer-Danfoss, the Sauer-Danfoss
logotype, the Sauer-Danfoss S-icon, PLUS+1™, What really matters is inside® and Know-How in Motion™ are
trademarks of the Sauer-Danfoss Group.
Frontpage: F300 211, F300 212, F300 351, F300 145, 151-1976

2 520L0407 • Rev EK • Jun 2013

 OMS, OMT and OMV
Technical Information
A Wide Range of Orbital Motors

The programme is characterised by technical features appealing to a large number

of applications and a part of the programme is characterised by motors that can be
adapted to a given application. Adaptions comprise the following variants among
others:

•• Motors with corrosion resistant parts

•• Wheel motors with recessed mounting flange
•• OMP, OMR- motors with needle bearing
•• OMR motor in low leakage version
•• OMR motors in a super low leakage version
•• Short motors without bearings
•• Ultra short motors
•• Motors with integrated positive holding brake
•• Motors with integrated negative holding brake
•• Motors with integrated flushing valve
•• Motors with speed sensor
•• Motors with tacho connection
•• All motors are available with black finish paint

The Sauer–Danfoss orbital motors are used in the following application areas:

•• Construction equipment
•• Agricultural equipment
•• Material handling & Lifting equipment
•• Forestry equipment
•• Lawn and turf equipment
•• Special purpose
•• Machine tools and stationary equipment
•• Marine equipment

Survey of Literature with Detailed data on all Sauer-Danfoss motors can be found in our motor catalogue, which is
Technical Data on Sauer- divided into 5 individual subcatalogues:
Danfoss Orbital Motors •• General information on Sauer-Danfoss orbital motors: function, use, selection of
orbital motor, hydraulic systems, etc.
•• Technical data on small motors: OML and OMM
•• Technical data on medium sized motors: OMP, OMR, OMH and OMEW
•• Technical data on medium sized motors: DH and DS
•• Technical data on large motors: OMS, OMT and OMV
•• Technical data on large motors: TMT

A general survey brochure on Sauer-Danfoss orbital motors gives a quick motor

reference based on power, torque, speed and capabilities.

520L0407 • Rev EK • Jun 2013 3

 OMS, OMT and OMV
Technical Information
Contents

Contents OMS, OMT and OMV......................................................................................................... 5

Speed, Torque and Output........................................................................................................................... 5

OMS ................................................................................................................................... 6
Versions............................................................................................................................................................... 6
Code Numbers................................................................................................................................................. 7
Technical data for OMS.................................................................................................................................. 8
Max. Permissible Shaft Seal Pressure.................................................................................................. 9
Pressure Drop in Motor............................................................................................................................ 9
Oil Flow in Drain Line..............................................................................................................................10
Direction of Shaft Rotation...................................................................................................................10
Permissible Shaft Loads.........................................................................................................................11
Function Diagrams..................................................................................................................................14
Shaft Version..............................................................................................................................................19
Port Thread Versions...............................................................................................................................22
Dimension........................................................................................................................................................23
OMSS..................................................................................................................................................................32

OMT................................................................................................................................. 34
Versions.............................................................................................................................................................34
Code Numbers...............................................................................................................................................35
Technical data.................................................................................................................................................36
Max. Permissible Shaft Seal Pressure................................................................................................38
Pressure Drop in Motor..........................................................................................................................39
Oil Flow in Drain Line..............................................................................................................................39
Direction of Shaft Rotation...................................................................................................................39
Permissible Shaft Loads.........................................................................................................................40
Function Diagrams..................................................................................................................................42
Shaft Version..............................................................................................................................................45
Port Thread Versions...............................................................................................................................48
Dimensions......................................................................................................................................................49
OMTS..................................................................................................................................................................56

OMV................................................................................................................................. 58
Versions.............................................................................................................................................................58
Code Numbers...............................................................................................................................................59
Technical data . ..............................................................................................................................................60
Max. Permissible Shaft Seal Pressure................................................................................................61
Pressure Drop in Motor..........................................................................................................................62
Oil Flow in Drain Line..............................................................................................................................62
Direction of Shaft Rotation...................................................................................................................62
Permissible Shaft Loads.........................................................................................................................63
Function Diagrams..................................................................................................................................65
Shaft Version..............................................................................................................................................68
Port Thread Versions...............................................................................................................................71
Dimensions......................................................................................................................................................72
OMVS.................................................................................................................................................................78

Weight of Motors ........................................................................................................... 80

4 520L0407 • Rev EK • Jun 2013

 OMS, OMT and OMV
Technical Information
Data Survey

OMS, OMT and OMV Max. speed

min-1
Speed, Torque and (rpm)
Output 800
600
400
200

80 100 125 160 200 250 315 400 500 160 200 250 315 400 500 315 400 500 630 800

lbf•in Nm Max. Torque

22000
2400
20000
2200

18000 2000

16000 1800

14000 1600

1400
12000

1200
10000
1000
8000
800
6000
600

4000
400

2000 200

80 100 125 160 200 250 315 400 500 160 200 250 315 400 500 315 400 500 630 800

hp kW Max. output
80 60
50
60 40
40 30
20
20 10

80 100 125 160 200 250 315 400 500 160 200 250 315 400 500 315 400 500 630 800

OMS OMT OMV

Intermittend values Continuous values 151-1407.11

The bar diagrams above are useful for a quick selection of relevant motor size for the
application. The final motor size can be determined by using the function diagram for
each motor size.
•• OMS can be found on pages 14-18
•• OMT can be found on pages 42-44
•• OMV can be found on pages 65-67
The function diagrams are based on actual tests on a representative number of motors
from our production. The diagrams apply to a return pressure between 5 and 10 bar
[75 and 150 psi] when using mineral based hydraulic oil with a viscosity of 35 mm2/s
[165 SUS] and a temperature of 50°C [120°F]. For further explanation concerning how to
read and use the function diagrams, please consult the paragraph "Selection of motor
size" in the technical information "General Orbital motors" 520L0232.

520L0407 • Rev EK • Jun 2013 5

 OMS
Technical Information
Versions

OMS
Versions

Main type designation

European version

Drain connection
Mounting flange

Check valve
US version
Port size
Shaft

Cyl. 32 mm G 1/2 l Yes Yes OMS

Cyl. 1.25 in 7/8-14 UNF l Yes Yes OMS
G 1/2 l Yes Yes OMS
Standard Splined 1.25 in
7/8-14 UNF l Yes Yes OMS
flange
Tapered 35 mm G 1/2 l Yes Yes OMS
Tapered 1.25 in 7/8-14 UNF l Yes Yes OMS
P.t.o. G 1/2 l Yes Yes OMS
Special flange Splined 1.25 in G 1/2 l Yes Yes OMS
Cyl. 1 in 7/8-14 UNF l Yes Yes OMS
Cyl. 1.25 in 7/8-14 UNF l Yes Yes OMS
A-2
Splined 1 in 7/8-14 UNF l Yes Yes OMS
flange
Splined 1.25 in 7/8-14 UNF l Yes Yes OMS
Tapered 1.25 in 7/8-14 UNF l Yes Yes OMS
Cyl. 1 in 7/8-14 UNF l Yes Yes OMS
Magneto Cyl. 1.25 in 7/8-14 UNF l Yes Yes OMS
flange Splined 1 in 7/8-14 UNF l Yes Yes OMS
Splined 1.25 in 7/8-14 UNF l Yes Yes OMS
Splined 1.25 in 7/8-14 UNF l Yes Yes OMS
SAE B flange
Splined 0.875 in 7/8-14 UNF l Yes Yes OMS
Cyl. 32 mm G 1/2 l Yes Yes OMSW
Cyl. 1.25 in 7/8-14 UNF l Yes Yes OMSW
Wheel
Tapered 35 mm G 1/2 l Yes Yes OMSW
Tapered 1.25 in 7/8-14 UNF l Yes Yes OMSW
Short No output shaft G 1/2 l Yes Yes OMSW
Function diagram - see page : →

Features available (options) :

Speed sensor
Motor with tacho connection
High pressure shaft seal
Viton shaft seal
Painted
Ultra short
Motor with drum brake

6 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Code Numbers

Code Numbers
Displacement [cm3]

Technical data – Page

Dimensions – Page
Shaft loads – Page
Code Numbers

80 100 125 160 200 250 315 400 500

151F 0500 0501 0502 0503 0504 0505 0506 0605 - 8 11 23
151F 2200 2201 2202 2203 2204 2205 2206 2261 2268 8 11 24
151F 0507 0508 0509 0510 0511 0512 0513 - - 8 11 23
151F 2207 2208 2209 2210 2211 2212 2213 2262 2269 8 11 24
151F 0514 0515 0516 0517 0518 0519 0520 - - 8 11 23
151F 2214 2215 2216 2217 2218 2219 2220 2264 2270 8 11 24
151F 0560 0561 0562 0563 0564 0565 0566 - - 8 11 23
151F 0542 0543 0544 0545 0546 0547 0548 - - 8 12 25
151F 2300 2301 2302 2303 2304 2305 2306 2307 2345 8 12 26
151F 2316 2317 2318 2319 2320 2321 2322 2323 2347 8 11 26
151F 2308 2309 2310 2311 2312 2313 2314 2315 2346 8 12 26
151F 2324 2325 2326 2327 2328 2329 2330 2331 2348 8 11 26
151F 2332 2333 2334 2335 2336 2337 2338 2339 2349 8 11 26
151F 2377 2378 2379 2380 2381 2382 2383 2384 2385 8 12 27
151F 2368 2369 2370 2371 2372 2373 2374 2375 2376 8 11 27
151F 2359 2360 2361 2362 2363 2364 2365 2366 2367 8 12 27
151F 2350 2351 2352 2353 2354 2355 2356 2357 2358 8 11 27
151F 2395 2396 2397 2398 2399 2400 2401 2402 2403 8 11 28
151F 2413 2414 2415 2416 2417 - - - - 8 13 28
151F 0521 0522 0523 0524 0525 0526 0527 0610 - 8 11 29
151F 2235 2236 2237 2238 2239 2240 2241 2265 2266 8 11 30
151F 0528 0529 0530 0531 0532 0533 0534 0609 - 8 11 29
151F 2242 2243 2244 2245 2246 2247 2248 2263 2267 8 11 30
151F 0535 0536 0537 0538 0539 0540 0541 0608 - 8 - 31
14 14 15 15 16 16 17 17 18

Ordering
Add the four digit prefix “151F” to the four digit numbers from the chart for complete
code number.

Example:
151F0504 for an OMS 200 with standard flange, cyl. 32 mm shaft and port size G 1/2.

Note: Orders will not be accepted without the four digit prefix.

520L0407 • Rev EK • Jun 2013 7

 OMS
Technical Information
Technical Data

Technical data for OMS

OMS OMS OMS OMS OMS OMS OMS OMS OMS
Type OMSW OMSW OMSW OMSW OMSW OMSW OMSW OMSW OMSW
OMSS OMSS OMSS OMSS OMSS OMSS OMSS OMSS OMSS
Motor size 80 100 125 160 200 250 315 400 500
cm3 80.5 100.0 125.7 159.7 200.0 250.0 314.9 393.0 488.0
Geometric displacement
[in3] [4.91] [6.10] [7.67] [9.75] [12.20] [15.26] [19.22] [23.98] [29.78]
min-1 cont. 810 750 600 470 375 300 240 190 155
Max. speed
[rpm] int1) 1000 900 720 560 450 360 285 230 185
240 305 375 490 610 720 825 865 850
cont.
Nm [2120] [2700] [3320] [4340] [5400] [6370] [7300] [7660] [7520]
Max. torque
[lbf·in] 310 390 490 600 720 870 1000 990 990
int.1)
[2740] [3450] [4340] [5310] [6370] [7700] [8850] [8760] [8760]
15.5 18.0 18.0 16.5 16.5 14.5 15.0 11.0 9.0
cont.
kW [20.8] [24.1] [24.1] [22.1] [22.1] [19.4] [20.1] [14.8] [12.1]
Max. output
[hp] 19.5 22.5 22.5 23.0 22.0 18.0 17.0 12.5 10.5
int.1)
[26.2] [30.2] [30.2] [30.8] [29.5] [24.1] [22.8] [16.8] [14.1]
210 210 210 210 210 200 200 160 120
cont.
[3050] [3050] [3050] [3050] [3050] [2900] [2900] [2320] [1740]
bar 275 275 275 260 250 250 240 190 140
Max. pressure drop int.1)
[psi] [3990] [3990] [3990] [3770] [3630] [3630] [3480] [2760] [2030]
295 295 295 280 270 270 260 210 160
peak2)
[4280] [4280] [4280] [4060] [3920] [3920] [3770] [3050] [2320]
65 75 75 75 75 75 75 75 75
cont.
l/min [17.2] [19.8] [19.8] [19.8] [19.8] [19.8] [19.8] [19.8] [19.8]
Max. oil flow
[USgal/min] 80 90 90 90 90 90 90 90 90
int.1)
[21.1] [23.8] [23.8] [23.8] [23.8] [23.8] [23.8] [23.8] [23.8]
Max. starting pressure bar 12 10 10 8 8 8 8 8 8
with unloaded shaft [psi] [175] [145] [145] [115] [115] [115] [115] [115] [115]
at max. press. drop cont. 180 230 290 370 470 560 710 710 660
Nm [lbf·in] [1590] [2040] [2570] [3270] [4160] [4960] [6280] [6280] [5840]
Min. starting torque
at max. press. drop int.1) 235 300 380 460 560 700 850 840 770
Nm [lbf·in] [2080] [2660] [3360] [4070] [4960] [6200] [7520] [7430] [6820]

Max. return pressure

Type Max. inlet pressure
with drain line
bar 230 140
cont.
[psi] [3340] [2030]
OMS
bar 295 175
OMSW int.1)
[psi] [4280] [2540]
OMSS
bar 300 210
peak2)
[psi] [4350] [3050]

Splined 1 in Cyl. 1 in Splined 0.875 in

Nm cont. 360 [3190] 300 [2660] 200 [1770]
*Max torque for shaft type
[lbf·in] int.1) 450 [3980] 410 [3630] 200 [1770]

1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
2)
Peak load: the permissible values may occur for max. 1% of every minute.

For max. permissible combination of flow and pressure, see function diagram for actual motor.

8 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Technical Data

Max. Permissible Shaft OMS with standard shaft seal, OMS with standard shaft seal,
Seal Pressure check valves and without use check valves and with drain
of drain connection: connection:
The pressure on the shaft seal The shaft seal pressure equals
never exceeds the pressure in the pressure on the drain line.
the return line 151-320.10

Max. return pressure without drain line or max. pressure in the drain line
P P
psi bar
1500
100
90
1200
80
70
900
60
50
600 40
30
300 20
10
0 0
0 100 200 300 400 500 600 700 800 max. min-1
(rpm)

151-1674.10

– – – – Intermittent operation: the permissible values may occur for max. 10% of every minute.
Continuous operation

Pressure Drop in Motor ∆p ∆p

psi bar
16

200 14

12
150 10

8
100
6

4
50
2

0 0 Q
0 10 20 30 40 50 60 70 80 90 l/min

Q
0 2 4 6 8 10 12 14 16 18 20 22 US gal/min

151-1408.10

The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]

520L0407 • Rev EK • Jun 2013 9

 OMS
Technical Information
Technical Data

Oil Flow in Drain Line The table shows the max. oil flow in the Pressure drop Viscosity Oil flow in
drain line
drain line at a return pressure less than
bar mm2/s l/min
5-10 bar [75-150 psi]. [psi] [SUS] [US gal/min]
20 [100] 1.5 [0.40]
140 [2030]
35 [165] 1.0 [0.26]
20 [100] 3.0 [0.79]
210 [3050]
35 [165] 2.0[0.53]

Direction of Shaft
Rotation

10 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Technical Data

Permissible Shaft Loads Mounting flange: Shaft:

for OMS Standard – A-2 – Magneto – SAE B Cyl. 32 mm – Cyl. 1.25 in – Splined 1.25 in.
Prad. Prad. Tapered 35 mm – Tapered 1.25 in – P.t.o.
lbf N
7000
30000
0
6000 - + Pmax. =5000 N
=1124 lbf
25000
5000
20000
4000
15000
3000

10000
2000

5000
1000

0 0
-20 -10 0 10 20 30 40 50 60 70 80 mm

-0.5 0 0.5 1 1.5 2 2.5 3 in

151-1962.10

Mounting flange: Shaft:

Wheel All shaft types
Prad. Prad.
lbf N
7000
30000
0
6000 - + Pmax. =5000 N
=1124 lbf
25000
5000
20000
4000
15000
3000

10000
2000

5000
1000

0 0
0 10 20 30 40 50 60 70 80 90 100 110 mm

0 0.5 1 1.5 2 2.5 3 3.5 4 in

151-1964.10

The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of
the distance from the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at
100 min-1) at rated output torque, when mineral-based hydraulic oil with a sufficient
content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown
in the curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the
chapter "Bearing dimensioning" in the technical information "General Orbital motors"
520L0232.

520L0407 • Rev EK • Jun 2013 11

 OMS
Technical Information
Technical Data

Permissible Shaft Loads Mounting flange: Shaft:

for OMS Special Splined 1.25 in
Prad. Prad.
lbf N
7000
30000
0
6000 - + Pmax. =5000 N
=1124 lbf
25000
5000
20000
4000
15000
3000

10000
2000

5000
1000

0 0
-20 -10 0 10 20 30 40 50 60 70 80 mm

-0.5 0 0.5 1 1.5 2 2.5 3 in

151-1960.10

Mounting flange: Shaft:

A-2 – Magneto Cyl. 1 in – Splined 1 in
Prad. Prad.
lbf N

20000
0
4000 - + Pmax. =5000 N
=1124 lbf

15000
3000

10000
2000

5000
1000

0 0
-20 -10 0 10 20 30 40 50 60 mm

-0.5 0 0.5 1 1.5 2 in

151-1961.10

The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of
the distance from the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at
100 min-1) at rated output torque, when mineral-based hydraulic oil with a sufficient
content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown
in the curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the
chapter "Bearing dimensioning" in the technical information "General Orbital motors"
520L0232.

12 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Technical Data

Permissible Shaft Loads Mounting flange: Shaft:

for OMS SAE B Splined 0.875 in
Prad. Prad.
lbf N

20000
0
4000 - + Pmax. =5000 N
=1124 lbf

15000
3000

10000
2000

5000
1000

0 0
-20 -10 0 10 20 30 40 50 60 mm

-0.5 0 0.5 1 1.5 2 in

151-1963.10

The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of
the distance from the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at
100 min-1) at rated output torque, when mineral-based hydraulic oil with a sufficient
content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown
in the curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the
chapter "Bearing dimensioning" in the technical information "General Orbital motors"
520L0232.

520L0407 • Rev EK • Jun 2013 13

 OMS
Technical Information
Function Diagrams

Function Diagrams OMS 80

Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

30 l/min
[7.9 US gal/min]

40 l/min
[10.6 US gal/min]

50 l/min
[13.2 US gal/min]

65 l/min
[17.2 US gal/min]

Q=80 l/min
[21.1 US gal/min]
lbf•in Nm

3000
325
∆ p=275 bar
300 3990 psi
2500 250 bar
275
N=18kW 3630 psi
250
225 bar
2000 15kW 3260 psi
225 9kW
12kW 210 bar
18hp
200 3050 psi
15hp
175 6kW 175 bar
1500 9hp 2540 psi
6hp
150 140 bar
12hp
3kW 2030 psi
125
1000
100 ηt =81% 105 bar
1520 psi
3hp 80%
75
70 bar
500 78% 1020 psi
50 1hp 75%
N=1kW 70%
25 ηt =60% ∆ p= 30 bar
440 psi
0 0

0 100 200 300 400 500 600 700 800 900 1000 min-1
(rpm)

151-901.10

OMS 100
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

30 l/min
[7.9 US gal/min]

40 l/min
[10.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]

lbf•in Nm

4000 450

3500 400 ∆ p=275 bar

3990 psi
350 250 bar
3000 15kW N=18kW 3630 psi
12kW 225 bar
300 9kW 18hp 3260 psi
2500 210 bar
3050 psi
250
12hp 15hp 175 bar
2000 6kW 2540 psi
200
1500 3kW 6hp ηt =83% 140 bar
2030 psi
150
3hp 105 bar
1000 80% 1520 psi
100
N=1kW 70 bar
1hp 75% 1020 psi
500 50 70%
ηt =60% ∆ p= 35 bar
510 psi
0 0

0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 min-1
(rpm)

151-902.10

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent torque for the actual shaft version can be
found on page 8.

Intermittent pressure drop and oil flow must not occur simultaneously.

14 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Function Diagrams

Function Diagrams
OMS 125

Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

30 l/min
[7.9 US gal/min]

40 l/min
[10.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf•in Nm

4500 500 ∆ p=275 bar

3990 psi
4000 450
N=21kW 250 bar
3630 psi
3500 400
21hp 18kW 225 bar
15kW 3260 psi
350 12kW
3000 210 bar
9kW 3050 psi
300 12hp 15hp 18hp 175 bar
2500 6kW 2540 psi
250
2000
6hp 9hp ηt =85% 140 bar
2030 psi
200 83%
1500 3hp 3kW 105 bar
150 1520 psi
80%
1000 100 70 bar
75% 1020 psi
1hp N=1kW 70%
500 50
ηt =60% ∆ p= 35 bar
510 psi
0 0

0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 min-1
(rpm)

151-903.10

OMS 160
lbf•in Nm
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

30 l/min
[7.9 US gal/min]

40 l/min
[10.6 US gal/min]

50 l/min
[13.2 US gal/min]

60 l/min
[15.9 US gal/min]

75 l/min
[19.8 US gal/min]

Q=90 l/min
[23.8 US gal/min]
6000

600 ∆ p=260 bar

5000 3770 psi
550
18hp 18kW N=21kW
225 bar
500 3260 psi
12kW 15kW 210 bar
4000 450 3050 psi
6hp 6kW 9kW
15hp
400 175 bar
21hp 2540 psi
350 12hp 160 bar
3000 9hp
2320 psi
300 140 bar
2030 psi
250
2000 3hp 105 bar
3kW
200 1520 psi
ηt =87%
150
N=1kW 86% 85% 83% 70 bar
1000 80% 1020 psi
100 1hp 75%
70%
50
ηt =60% ∆ p= 35 bar
510 psi
0 0

0 50 100 150 200 250 300 350 400 450 500 550 600 min-1
(rpm)

151-904.11

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent torque for the actual shaft version can be
found on page 8.

Intermittent pressure drop and oil flow must not occur simultaneously.

520L0407 • Rev EK • Jun 2013 15

 OMS
Technical Information
Function Diagrams

Function Diagrams
OMS 200

Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

30 l/min
[7.9 US gal/min]

40 l/min
[10.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf•in Nm

7000
750

6000
700 ∆ p=250 bar
650 3630 psi
15hp 225 bar
N=21kW
600 3260 psi
9kW 15kW 18kW
5000 12kW 210 bar
550 12hp
6kW 3050 psi
500 175 bar
18hp 21hp 2540 psi
4000 450
6hp 160 bar
400 2320 psi
9hp 140 bar
3000 350 2030 psi
300
ηt =88% 105 bar
250 86% 1520 psi
2000 3kW 85%
200
N=1kW 3hp 83% 80% 70 bar
150 1020 psi
1000 1hp 75%
100 70%
ηt =60% ∆ p= 30 bar
50 440 psi
0 0

0 50 100 150 200 250 300 350 400 450 500 min-1
(rpm)

151-905.10

OMS 250
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

30 l/min
[7.9 US gal/min]

40 l/min
[10.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]

lbf•in Nm

8000 900 ∆ p=250 bar

3630 psi

7000 800 225 bar

3260 psi
15kW 18kW N=21kW
700 12kW 200 bar
6000 9kW 2900 psi
175 bar
600 6kW 15hp 2540 psi
5000 18hp 21hp
155 bar
500 2250 psi
9hp 12hp
4000 140 bar
6hp 2030 psi
400
125 bar
3000 1810 psi
300 3hp 3kW 86% 85%
83% 95 bar
80% 1390 psi
2000 75%
200
N=1kW ηt =87% 70 bar
70% 1020 psi
1hp
1000 100
ηt =60% ∆ p= 35 bar
510 psi
0 0

0 50 100 150 200 250 300 350 400 min-1

(rpm)

151-1039.10

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent torque for the actual shaft version can be
found on page 8.

Intermittent pressure drop and oil flow must not occur simultaneously.

16 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Function Diagrams

Function Diagrams
OMS 315

Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

30 l/min
[7.9 US gal/min]

40 l/min
[10.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf•in Nm

10000
1100 ∆ p=240 bar
3480 psi
9000
1000 225 bar
3260 psi
8000 900
N=18kW 200 bar
2900 psi
7000 800 175 bar
15kW 2540 psi
6000 700 9kW 160 bar
12kW 18hp 2320 psi
600 15hp 140 bar
5000 12hp 2030 psi
500 6kW 9hp 120 bar
4000 1740 psi
400 6hp 100 bar
3kW
3000 ηt =87% 80% 1450 psi
300
3hp 70 bar
N=1kW 85% 75% 1020 psi
2000
200 1hp 83% 70%
1000 100 ηt =60% ∆ p= 35 bar
510 psi
0 0

0 25 50 75 100 125 150 175 200 225 250 275 300 min-1
(rpm)

151-906.10

OMS 400
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

30 l/min
[7.9 US gal/min]

40 l/min
[10.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]

lbf•in Nm

10000
1100 ∆ p=190 bar
2760 psi
9000 175 bar
1000
N=15kW 2540 psi
8000 900
160 bar
2320 psi
7000 800
12kW 140 bar
2030 psi
6000 700
6kW 9kW 15hp 120 bar
600 1740 psi
5000 9hp
3kW 12hp 105 bar
500 6hp 1520 psi
4000
400
3hp
ηt =87% 80 bar
3000 1160 psi
300 N= 85% 60 bar
86%
2000 1kW 83% 870 psi
200 1hp 80%
1000 100
75%
70%
∆ p= 30 bar
ηt =60% 440 psi
0 0

0 25 50 75 100 125 150 175 200 225 250 min-1

(rpm)

151-1491.10

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent torque for the actual shaft version can be
found on page 8.

Intermittent pressure drop and oil flow must not occur simultaneously.

520L0407 • Rev EK • Jun 2013 17

 OMS
Technical Information
Function Diagrams

Function Diagrams OMS 500

Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

30 l/min
[7.9 US gal/min]

40 l/min
[10.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf•in Nm

10000
1100
9000
1000

8000 900 N=12kW ∆ p=140 bar

9kW 2030 psi
6hp 6kW
7000 800
12hp 120 bar
1740 psi
6000 700
105 bar
600 3kW ηt =88% 86% 85% 1520 psi
5000 9hp
90 bar
500 83% 1300 psi
4000 3hp
80 bar
400 80% 1160 psi
3000
300 N=
1kW 75%
2000 1hp 70% 50 bar
200 730 psi
ηt =60%
1000 100 ∆ p= 25 bar
360 psi
0 0

0 25 50 75 100 125 150 175 200 min-1

(rpm)

151-1984.10

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent torque for the actual shaft version can be
found on page 8.

Intermittent pressure drop and oil flow must not occur simultaneously.

18 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Shaft Version

Shaft Version

58 [2.28]

45˚ 18 [0.71]

R0.6 [0.024] 6 [0.24] A-A

A: Cylindrical 32 mm shaft
D: Parallel key A
A10 × 8 × 45

Ø32.018 [1.2605]
Ø32.002 [1.2599]
DIN 6885

35.00 [1.378]
34.71 [1.367]
Ø35 [1.38]
Keyway deviates from A

M8
standard

A D
45.5 [1.791] 5.5 [0.217] 10.000 [0.3937]
45.0 [1.772] 4.5 [0.177] 9.964 [0.3923]
56.5 [2.224]

48.4 [1.906]
47.6 [1.874]
min. 20 [0.78]
45˚
R0.4 [0.016] 3/8 -16 UNC A-A
B: Cylindrical 1.25 in shaft A
E: Parallel key
Ø31.750 [1.2500]
Ø31.699 [1.2480]

5/16 × 5/16 × 11/4 in

Ø35 [1.38]

35.33 [1.391]
35.08 [1.381]
SAE J744 B
Keyway deviates from
standard
A
9.4 [0.370] E
7.5 [0.295]
31.75 [1.250] 7.962 [0.3135]
31.37 [1.235] 7.937 [0.3125]

43.4 [1.708]
42.6 [1.678]
R0.5 [0.020]
min. 20 [0.78]

R4 [0.16] 3/8 -16 UNC A-A

C: Cylindrical 1 in shaft A
F: Parallel key
Ø25.40 [1.000]
Ø25.38 [0.999]

1/4 × 1/4 × 11/4 in

Ø35 [1.38]

28.2 [1.110]
27.9 [1.098]

B.S. 46 C
Keyway deviates from
standard

A 3.0 [0.118] F
2.0 [0.079]
6.40 [0.252]
31.75 [1.250] 6.35 [0.250]
31.37 [1.235]

151-876.10

520L0407 • Rev EK • Jun 2013 19

 OMS
Technical Information
Shaft Version

Shaft Version

58 [2.28]

18 [0.71]
45˚ 6 [0.24] A-A
R0.4 [0.016]

Ø31.750 [1.2500]
Ø31.725 [1.2490]
Ø35 [1.38]

M8
D. Involute splined shaft
ANS B92.1 - 1970 standard
Flat root side fit
Pitch 12/24
A
Teeth 14 38 [1.50]
Major dia. 1.25 in 36 [1.42]
Pressure angle 30°

48.4 [1.906]
47.6 [1.874]
min. 20 [0.78]

45˚
R0.4 [0.016] 3/8 -16 UNC A-A
A
US version
Ø31.750 [1.2500]
Ø31.725 [1.2490]

E: Involute splined shaft

Ø35 [1.38]

ANS B92.1 - 1970 standard

Flat root side fit E
Pitch 12/24
Teeth 14
Major dia. 1.25 in A
Pressure angle 30° 35 [1.38]
32 [1.26]

min. 14 [0.55]

R2 [0.08]
A-A
¼ -20 UNC-2B *6.275 [0.2470]
*6.200 [0.2441]
A
Ø25.348 [0.9979]
Ø25.298 [0.9960]

F: Splined shaft
Ø35 [1.38]

SAE 6 B (B.S. 2059)

F
Straight-sided,
bottom fitting, deep.
6x60˚
Fit 2
Nom. size 1 in A
22.3 [0.878] 1[0.04]x45˚ *21.54 [0.848]
45˚ *21.40 [0.843]
*Deviates from 21.7 [0.854]

SAE 6 B (B.S. 2059) 43.4 [1.709]

42.6 [1.677]

151-1912.11

20 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Shaft Version

Shaft Version

Ø18.6 [0.732]
Ø18.4 [0.724]
A-A
A

Ø22.1 [0.870]
Ø21.9 [0.862]
Ø35 [1.38]
G. Involute splined shaft G
ANS B92.1 - 1970 standard
Flat root side fit
Pitch 16/32 A
R4 [0.16]
Teeth 13 R2.5 [0.098]
Major dia. 0.875 in 13.5 [0.531]
12.5 [0.492]
Pressure angle 30° 33.2 [1.307]
32.8 [1.291]

J K
A-A
H: Tapered 35 mm shaft A
(ISO/R775)
K: DIN 937 M20x1.5 [0.591]
Ø4.5 [0.177]
Ø35 [1.38]

Across flats: 41 mm Ø44 [1.73]

H

19.0 [0.748]
19.1.[0.752]
Tightening torque:
200 ± 10 Nm [1770 ±85 lbf·in]
J: Taper 1:10
L: Parallel key A L
B6 × 6 × 20 4 [0.16] 13 [0.51] 6.00 [0.236]
DIN 6885 5.97 [0.235]
20 [0.79]
Keyway deviates from
standard 36 [1.42]

58 [2.28]

54.3 [2.138]
I: Tapered 1 1/4 in shaft 53.7 [2.114]
N: Cone 1:8 12.7 [0.500]
SAE J501
M
M: 1 - 20 UNEF 5 [0.20] A-A
45˚
Across flats 1 7/16 in A N
Tightening torque:
Ø31.775 [1.2510]
Ø31.725 [1.2490]

200 ± 10 Nm (1770 ±85 lbf·in)

Ø35 [1.38]

Ø4 [0.15]

O: Parallel key I
17.16 [0.676]
16.94 [0.677]

/16 × /16 × 1 /4
5 5 1

SAE J501
Keyway deviates from
A
standard O
31.75 [1.250]
31.37 [1.235]
7.960 [0.3134]
35.6 [1.402]
7.940 [0.3126]
34.4 [1.354]

151-1915.10

520L0407 • Rev EK • Jun 2013 21

 OMS
Technical Information
Technical Data

Shaft Version

100 [3.94]

R0.5 [0.020] R6.7 [0.267]

45˚
R5 [0.20] A-A
60˚

8.6 3 [0.3
A

8.5
4[
0.3 36]
40
Ø34.85 [1.372]
Ø34.73 [1.367]

]
29.5 [1.161]
29.3 [1.154]
Ø40 [1.57]

J. P.t.o. shaft
DIN 9611 Form 1 J
(ISO/R500 without pin hole)

** Deviates from DIN 9611 A 7 [0.28] 28.14 [1.108]

27.89 [1.098]
38.25 [1.506]
37.75 [1.486]
77 [3.03]
75 [2.95]

151-1948.10

Port Thread Versions B

A Ø34.4 [1.354]
Ø34.0B[1.339]
E F
A
min. 16.7 [0.657]
min. 16 [0.63]

Ø34.4 [1.354]
Ø34.0 [1.339]
E F
min. 16.7 [0.657]
min. 16 [0.63]

A: G main ports B: UNF main ports

E: ISO 228/1 - G1/2 F: 7/8 - 14 UNF
O-ring boss port D
C Ø21.4 [0.843]
Ø21.0 [0.827]
D
G
C Ø21.4H
min. 12 [0.47]

[0.843]
min. 12 [0.47]

Ø21.0 [0.827]

G H
min. 12 [0.47]
min. 12 [0.47]

151-1971.11

151-1971.11

C: G drain port D: UNF drain port

G: ISO 228/1 - G1/4 H: 7/16 - 20 UNF
O-ring boss port

22 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Dimensions – European Version

Dimension Ø82.55 [3.250]

Standard Flange Ø82.50 [3.248]

1 [0.04]x45˚
R1 [0.04]
6.35 [0.250]
5.85 [0.230]
L3
Ø13.5 [0.531]
18 [0.71]

66.5 [2.618]
64.5 [2.539]
Ø20 [0.79]
L2

48 [1.89]
L1

C
L

5.6 [0.22]
4.4 [0.17]

D
22.6 [0.890]
21.4 [0.850]

27.6 [1.047]
26.4 [1.039]

16.3 [0.642] 16.3 [0.642] max. 54 [2.13]

max. 52 [2.05]
15.7 [0.618] 15.7 [0.618]
R18 [0.71]
21.3 [0.839] 21.3 [0.839]
56 [2.20]
20.7 [0.815] 20.7 [0.815]
70 [2.76]
Rmin. 14 [0.55]
max. 103 [4.06]

R13 [0.51]
40 [1.57]

R20 [0.78]

Lmax L1 L2 L3
Type mm mm mm Output shaft mm
[in] [in] [in] [in]
167 14.0 124 67
OMS 80 max
[6.57] [0.551] [4.88] All shafts except [2.64]
170 17.4 127 P.t.o. shaft 65
OMS 100 min
[6.69] [0.685] [5.00] [2.56]
175 21.8 132 109
OMS 125 max m
[6.89] [0.858] [5.20] [4.29] ax 106.8 [4.205]
P.t.o. shaft m
ax
.1
05 106.0 [4.173]
181 27.8 138 107 .1
28 [4
OMS 160 min [5
.1
3] max. 131 [5.157]
[7.13] [1.094] [5.43] [4.21] .0
4]
188 34.8 145 C: Drain connection
OMS 200
[7.40] [1.370] [5.71] G 1⁄4; 12 mm [0.47 in] deep
196 43.5 153 D: M10; 13 mm [0.51 in] deep
OMS 250
[7.72] [1.713] [6.02] E: G 1⁄2; 15 mm [0.59 in] deep
151-1809.10
208 54.8 165
OMS 315
[8.19] [2.157] [6.50]
221 68.4 178
OMS 400
[8.70] [2.693] [7.01]

520L0407 • Rev EK • Jun 2013 23

 OMS
Technical Information
Dimensions – US Version

Standard Flange Ø82.55 [3.250]

Ø82.50 [3.248]

1 [0.04]x45˚
R1 [0.04]
6.35 [0.250]
5.85 [0.230]
Ø13.5 [0.531]
L3
18 [0.71]

66.5 [2.618]
64.5 [2.539]
Ø21 [0.83]
L2

56 [2.20]
L1

C
L

5.6 [0.22]
4.4 [0.17]

D
22.6 [0.890]
21.4 [0.850]

27.6 [1.047]
26.4 [1.039]

16.3 [0.642] 16.3 [0.642] R18 [0.71] max. 52 [2.05] max. 54 [2.13]
15.7 [0.618] 15.7 [0.618]
21.3 [0.839] 21.3 [0.839]
20.7 [0.815] 20.7 [0.815] 40 [1.57]
70 [2.76]
max. 103 [4.06]

Lmax L1 L2 L3
Type mm mm mm Output shaft mm
[in] [in] [in] [in]
167 14.0 124 57
OMS 80 max
[6.57] [0.551] [4.88] Cyl.1.25 in [2.24]
170 17.4 127 Splined 1.25 in 55
OMS 100 min
[6.69] [0.685] [5.00] [2.17] 106.8 [4.205]
m
ax

106.0 [4.173]
.1
m

175 21.8 132 67

05
ax

OMS 125 max max. 131 [5.16]

[4
.1

.1
26

[6.89] [0.858] [5.20] [2.64]

3]
[4

Tapered 1.25 in
.9
6

181 27.8 138 65

]

OMS 160 min

[7.13] [1.094] [5.43] [2.56]
188 34.8 145 C: Drain connection
OMS 200
[7.40] [1.370] [5.71] 7
⁄16 - 20 UNF;
151-1972.10
196 43.5 153 12 mm [0.47 in] deep
OMS 250
[7.72] [1.713] [6.02] O-ring boss port
208 54.8 165 D: M10; 13 mm [0.51 in] deep
OMS 315 E: 7
⁄8 - 14 UNF;
[8.19] [2.157] [6.50]
221 68.4 178 16.7 mm [0.657 in] deep
OMS 400 O-ring boss port
[8.70] [2.693] [7.01]
221 68.4 178
OMS 500
[8.70] [2.693] [7.01]

24 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Dimensions – European Version

Ø82.55 [3.250]
Special Flange Ø82.50 [3.248]

1 [0.04]x45˚
R1 [0.04]
6.35 [0.250]
5.85 [0.230]
55 [2.17]
53 [2.09]

58 [2.28]
18 [0.71]

78.5 [3.091]
76.5 [3.012]
Ø20 [0.79]
L2

48 [1.89]
C
L1
L

5.6 [0.22]
4.4 [0.17]

E
22.6 [0.890]
21.4 [0.850]
27.6 [1.047]
26.4 [1.039]

16.3 [0.642] 16.3 [0.642] max. 52 [2.05] max. 54 [2.13]

R18 [0.71]
15.7 [0.618] 15.7 [0.618]
21.3 [0.839] 21.3 [0.839] 56 [2.20]
20.7 [0.815] 20.7 [0.815]
70 [2.76]
R10 [0.39]
max. 103 [4.06]
Ø11.5 [0.453]

Lmax L1 L2

max. 103 [4.06]

Type mm mm mm
[in] [in] [in]
178 14.0 136
OMS 80
[7.01] [0.551] [5.35]
182 17.4 140
OMS 100
[7.17] [0.685] [5.51]
Ø
186 21.8 144 Ø1 106
OMS 125 06 .8
.0 [4.
[7.32] [0.858] [5.67] [4 20 max. 103 [4.06]
.1 5]
73
192 27.8 150 ]
OMS 160
[7.56] [1.094] [5.91]
199 34.8 157
OMS 200
[7.83] [1.370] [6.18]
151-1810.10
208 43.5 166
OMS 250
[8.19] [1.713] [6.54]
219 54.8 177
OMS 315
[8.62] [2.157] [6.97]
232 68.4 190
OMS 400
[9.13] [2.693] [7.48]

C: Drain connection
G 1⁄4; 12 mm [0.47 in] deep
D: M10; 13 mm [0.51 in] deep
E: G 1⁄2; 15 mm [0.59 in] deep

520L0407 • Rev EK • Jun 2013 25

 OMS
Technical Information
Dimensions – US Version

Ø88.55 [3.250]
A-2 Flange Ø82.50 [3.248]

1 [0.04]x45˚
R1 [0.04]

6.35 [0.250]
5.85 [0.230]
Ø13.5 [0.531]

L3
18 [0.71]

66.5 [2.618]
64.5 [2.539]
Ø21 [0.83]
L2

56 [2.20]
L1

C
L

5.6 [0.22]
4.4 [0.17]

D
22.6 [0.890]
21.4 [0.850]

27.6 [1.047]
26.4 [1.039]

16.3 [0.642] 16.3 [0.642] max. 52 [2.05] max. 54 [2.13]

15.7 [0.618] 15.7 [0.618]
R18 [0.71]
21.3 [0.839] 21.3 [0.839]
20.7 [0.815] 20.7 [0.815]
70 [2.76] 40 [1.57]

max. 103 [4.06]

max. 131 [5.16]

106.8 [4.205]
106.0 [4.173]

Lmax L1 L2 L3
Type mm mm mm Output shaft mm
[in] [in] [in] [in]
167 14.0 124 52
OMS 80 max
[6.57] [0.551] [4.88] Cyl.1 in [2.05]
170 17.4 127 Splined 1 in 50
OMS 100 min
[6.69] [0.685] [5.00] [1.97]
175 21.8 132 57
m
ax

OMS 125 max

.1

[6.89] [0.858] [5.20] [2.24]

26

Cyl.1.25 in
[4
.9

Splined 1.25 in
6]

181 27.8 138 55

OMS 160 min
[7.13] [1.094] [5.43] [2.17]
188 34.8 145 67
OMS 200 max
[7.40] [1.370] [5.71] [2.64]
Tapered 1.25 in
196 43.5 153 65
OMS 250 min 151-1979.10
[7.72] [1.713] [6.02] [2.56]
208 54.8 165 C: Drain connection
OMS 315
[8.19] [2.157] [6.50] 7⁄16 - 20 UNF;
221 68.4 178 12 mm [0.47 in] deep
OMS 400
[8.70] [2.693] [7.01] O-ring boss port
221 68.4 178 D: M10; 13 mm [0.51 in] deep
OMS 500 E: 7⁄8 - 14 UNF;
[8.70] [2.693] [7.01]
16.7 mm [0.657 in] deep
O-ring boss port

26 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Dimensions – US Version

Ø88.55 [3.250]
Magneto Flange Ø82.50 [3.248]

0.3 [0.012]x45˚
2.6 [0.102]
18.9 [0.744]
Ø13.5 [0.531]

L3

Ø21 [0.83]

70 [2.75]
68 [2.68]
6xØ20 [0.79]
L2

56 [2.20]
L1
L

C
5.6 [0.22]
4.4 [0.17]

D
22.6 [0.890]
21.4 [0.850]

27.6 [1.047]
26.4 [1.039]

16.3 [0.642] 16.3 [0.642] max. 52 [2.05] max. 54 [2.13]

15.7 [0.618] 15.7 [0.618]
R18 [0.71]
21.3 [0.839] 21.3 [0.839]
20.7 [0.815] 20.7 [0.815]
70 [2.76]
max. 103 [4.06] 22.5
22.5˚ ˚
max. 136 [5.35]

Lmax L1 L2 L3
106.8 [4.205]
106.0 [4.173]

Type mm mm mm Output shaft mm

[in] [in] [in] [in]
171 14.0 128 49
OMS 80 max
[6.73] [0.551] [5.04] Cyl.1 in [1.93]
174 17.4 131 Splined 1 in 47
OMS 100 min
[6.85] [0.685] [5.16] [1.85]
179 21.8 136 54
OMS 125 max
[7.05] [0.858] [5.35] Cyl.1.25 in [2.13]
185 27.8 142 Splined 1.25 in 52
OMS 160 min
[7.28] [1.094] [5.59] [2.05]
192 34.8 149 C: Drain connection
OMS 200 151-1980.10
[7.56] [1.370] [5.87] 7
⁄16 - 20 UNF;
200 43.5 157 12 mm [0.47 in] deep
OMS 250 O-ring boss port
[7.87] [1.713] [6.18]
D: M10; 13 mm [0.51 in] deep
212 54.8 169 E: 7
⁄8 - 14 UNF;
OMS 315
[8.35] [2.157] [6.65] 16.7 mm [0.657 in] deep
225 68.4 182 O-ring boss port
OMS 400
[8.86] [2.693] [7.17]
225 68.4 182
OMS 500
[8.86] [2.693] [7.17]

520L0407 • Rev EK • Jun 2013 27

 OMS
Technical Information
Dimensions – US Version

Ø101.60 [4.000] Ø56.5 [2.224]

SAE-B Flange Ø101.55 [3.998] Ø55.5 [2.185]

1 [0.04]x45˚
R1 [0.04]

9.7 [0.382]
9.3 [0.366]
Ø14.3 [0.570]
18 [0.71]
L3

3.5 [0.138]
3.3 [0.130]
66.5 [2.618]
64.7 [2.547]
Ø21 [0.83]
L2

56 [2.20]
C
L

L1
5.6 [0.22]
4.4 [0.17]

D
22.6 [0.890]
21.4 [0.850]

27.6 [1.047]
26.4 [1.039]

16.3 [0.642] 16.3 [0.642] max. 52 [2.05] max. 54 [2.13]

15.7 [0.618] 15.7 [0.618]
R18 [0.71]
21.3 [0.839] 21.3 [0.839]
20.7 [0.815] 20.7 [0.815]
70 [2.76]
max. 103 [4.06]

Rmin. 14 [0.55]
Lmax L1 L2 L3
Type mm mm mm Output shaft mm
max. 174 [6.85]

146.05 [5.750]

[in] [in] [in] [in]

167 14.0 124 57
OMS 80 max
[6.57] [0.551] [4.88] [2.24]
Splined 1.25 in
170 17.4 127 55
OMS 100 min
[6.69] [0.685] [5.00] [2.17]
175 21.8 132 42
OMS 125 max
[6.89] [0.858] [5.20] [1.65]
Splined 0.875 in
181 27.8 138 40
R10 [0.39]

OMS 160 min

[7.13] [1.094] [5.43] [1.57]
m
ax

188 34.8 145 C: Drain connection

.1

OMS 200
26

[7.40] [1.370] [5.71]

[4

7⁄16 - 20 UNF; 40 [1.57]

.9
6]

196 43.5 153 12 mm [0.47 in] deep

OMS 250
[7.72] [1.713] [6.02] O-ring boss port
208 54.8 165 D: M10; 13 mm [0.51 in] deep
OMS 315 E: 7⁄8 - 14 UNF;
[8.19] [2.157] [6.50]
221 68.4 178 16.7 mm [0.657 in] deep
OMS 400 O-ring boss port 151-1981.10
[8.70] [2.693] [7.01]
221 68.4 178
OMS 500
[8.70] [2.693] [7.01]

28 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Dimensions – European Version

Wheel Ø125.000 [4.9213]

Ø124.937 [4.9188] max. Ø73 [2.87]

58 [2.28]
16˚

104 [4.09]
102 [4.02]

1 [0.04]x45˚
R1 [0.04]

R6 [0.24]
43.9 [1.738]
42.5 [1.673]

9 [0.35]
7 [0.28]
Ø20 [0.79]

28.5 [1.12]
16 [0.63]
L2

48 [1.89]
L1

C
5.6 [0.22]
4.4 [0.17]
L

E
22.6 [0.890]
21.4 [0.850]
27.6 [1.047]
26.4 [1.039]

16.3 [0.642] 16.3 [0.642] R18 [0.71] max. 52 [2.05] max. 54 [2.13]
15.7 [0.618] 15.7 [0.618]
21.3 [0.839] 21.3 [0.839] 56 [2.20]
20.7 [0.815] 20.7 [0.815]
70 [2.76]
max. 103 [4.06]
R12 [0.47]
max. 139 [5.46]

Lmax L1 L2
Type mm mm mm
[in] [in] [in]
OMSW 129 14.0 87
max. 139 [5.46]

80 [5.08] [0.551] [3.43]

OMSW 132 17.4 90 16
100 [5.20] [0.685] [3.54] 15 0.4 [6
9.6 .3
Ø13.5 [0.531]

[6. 15]
28
OMSW 137 21.8 95 3]
125 [5.39] [0.858] [3.74]
OMSW 143 27.8 101
160 [5.63] [1.094] [3.98]
OMSW 150 34.8 108
200 [5.91] [1.370] [4.25]
OMSW 158 43.5 116
250 [6.22] [1.713] [4.57]
OMSW 170 54.8 128 151-1812.10

315 [6.69] [2.157] [5.04]

OMSW 183 68.4 142
400 [7.20] [2.693] [5.59]
C: Drain connection
G 1⁄4; 12 mm [0.47 in] deep
D: M10; 13 mm [0.51 in] deep
E: G 1⁄2; 15 mm [0.59 in] deep

520L0407 • Rev EK • Jun 2013 29

 OMS
Technical Information
Dimensions – US Version

Wheel Ø127.05 [5.000]

Ø126.95 [4.998]

max. Ø73 [2.87]

16˚

1 [0.04]x45˚

R6 [0.24]
R1 [0.04]
L3

8 [0.31]
16 [0.63]

Ø21 [0.83]

28.5 [1.12]
L2

56 [2.20]
L1

C
L

5.6 [0.22]
4.4 [0.17]

D
22.6 [0.890]
21.4 [0.850]

27.6 [1.047]
26.4 [1.039]

16.3 [0.642] 16.3 [0.642]

max. 52 [2.05] max. 54 [2.13]
15.7 [0.618] 15.7 [0.618]
R18 [0.71]
21.3 [0.839] 21.3 [0.839]
20.7 [0.815] 20.7 [0.815]
70 [2.76]
max. 103 [4.06] R12 [0.47]
Ø13.5 [0.531]

Lmax L1 L2 L3
Type mm mm mm Output shaft mm
[in] [in] [in] [in]
max. 139 [5.46]

OMSW 130 14.0 88 94

max
80 [5.12] [0.551] [3.46] [3.70]
Cyl.1.25 in 4]
OMSW 133 17.4 91 92 37
min [6.
.9
100 [5.24] [0.685] [3.58] [3.62] Ø16
1

OMSW 138 21.8 96 104

max
125 [5.43] [0.858] [3.78] [4.09]
Tapered 1.25 in
OMSW 144 27.8 102 102
min
160 [5.67] [1.094] [4.02] [4.02]
OMSW 151 34.8 109 C: Drain connection max. 139 [5.46]

200 [5.94] [1.370] [4.29] 7⁄16 - 20 UNF;

OMSW 159 43.5 117 12 mm [0.47 in] deep
250 [6.26] [1.713] [4.61] O-ring boss port
OMSW 171 54.8 129 D: M10; 13 mm [0.51 in] deep
151-1982.10
315 [6.73] [2.157] [5.08] E: 7⁄8 - 14 UNF;
OMSW 184 68.4 142 16.7 mm [0.657 in] deep
400 [7.24] [2.693] [5.59] O-ring boss port
OMSW 184 68.4 142
500 [7.24] [2.693] [5.59]
C: Drain connection
G 1⁄4; 12 mm [0.47 in] deep
D: M10; 13 mm [0.51 in] deep E:
G 1⁄2; 15 mm [0.59 in] deep

30 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
Dimensions – European Version

Short

Lmax L1 L2
Type mm mm mm
[in] [in] [in]
OMSS 124 14.0 83
80 [4.88] [0.551] [3.27]
OMSS 128 17.4 86
100 [5.04] [0.685] [3.39]
OMSS 132 21.8 90
125 [5.20] [0.858] [3.54]
OMSS 138 27.8 96
160 [5.43] [1.094] [3.78]
OMSS 145 34.8 103
200 [5.71] [1.370] [4.06]
OMSS 154 43.5 112
250 [6.06] [1.713] [4.41]
OMSS 165 54.8 123
315 [6.50] [2.157] [4.84]
OMSS 179 68.4 137
400 [7.05] [2.693] [5.39]
C: Drain connection
G 1⁄4; 12 mm [0.47 in] deep
D: M10; 13 mm [0.51 in] deep E:
G 1⁄2; 15 mm [0.59 in] deep

520L0407 • Rev EK • Jun 2013 31

 OMS
Technical Information
OMSS

Installing the OMSS The cardan shaft of the OMSS motor acts as an “output shaft”. Because of the movement
of the shaft, no seal can be fitted at the shaft output.
Internal oil leakage from the motor will therefore flow into the attached component.

During start and operation it is important that the spline connection and the bearings
in the attached component receive oil and are adequately lubricated. To ensure that the
spline connection receives sufficient oil, a conical sealing ring between the shaft of the
attached component and the motor intermediate plate is recommended. This method is
used in the OMS.

The conical sealing ring (code. no. 633B9023) is supplied with the motor.

To ensure that oil runs to the bearings and other parts of the attached component, the
stop plate must have a hole in it (see fig. below).

We recommend an O-ring between motor and attached component. The O-ring

(code no. 151F1033) is supplied with the motor. If motor and attached component have
been separated, remember to refill before starting up. Fill the oil through the drain
connection.

OMSS 2.35 [0.093]

A C
2.25 [0.089]
Dimensions of the E
Attached Component K 0.25 [0.010] B
K 0.1˚
Ø61.5 [2.421]
Ø60.5 [2.382]
min. Ø40 [1.57]

Ø108.0 [4.252]
Ø107.6 [4.236]
min. Ø4 [0.16]

Ø40.5 [1.594]
Ø40.3 [1.587]
Ø100 [3.94]

K
33 [1.30]
31 [1.22]
Ø29.5 [1.161]
Ø28.5 [1.122]

15 [0.59]
Ø35.5 [1.398]
Ø34.5 [1.358]

G H
F 6.2 [0.244] 16.5 [0.650]
8.4 [0.331] 5.8 [0.228] 15.5 [0.610]
8.0 [0.315] 28 [1.10]
27.3 [1.075]
26.7 [1.051] 26 [1.02]
52.3 [2.059]
34.2 [1.346]
51.7 [2.035]
33.8 [1.331]

151-873.10

A: O-ring: 100 × 3 mm E: Internal drain channel

B: External drain channel F: M10; min. 15 mm [0.59 in] deep
C: Drain connection G 1⁄4; 12 mm [0.47 in] deep G: Oil circulation hole
D: Conical seal ring H: Hardened stop plate

32 520L0407 • Rev EK • Jun 2013

 OMS
Technical Information
OMSS

Internal Spline Data for The attached component must have internal splines corresponding to the external
the Component to be splines on the motor cardan shaft (see drawing below).
Attached
Material:
Case hardening steel with a tensile strength corresponding at least to 20 MoCr4
(900 N/mm2) or SAE 8620.

Hardening specification:
•• On the surface: HV = 750 ± 50
•• 0.7 ± 0.2 mm under the surface: HV = 560

Internal involute spline data

Standard ANS B92.1-1970, class 5 (corrected m · X = 0.8; m = 2.1166)

Flat root side fit mm in

Number of
z 12 12
teeth
Pitch DP 12/24 12/24 Rmin
Pressure angle 30° 30°
Pitch dia. D 25.4 1.0
Lo
Major dia. 1.10 0–0.004
Dri 28.0 0–0.1 So
Form dia. Dfi
27.6 1.09 Dri
(min.)
Di
Minor dia. Di 23.0 0+0.033 0.9055 0+0.0013
l Dfi
Space width
Lo 4.308 ±0.020 0.1696 ±0.0008 d D
(circular)
Tooth thickness
So 2.341 0.09217
(circular) 151-874.10
Fillet radius Rmin. 0.2 0.008
Max. mea
surement l 17.62 0+0.15 0.700 0–0.006
between pins*
Pin dia. d 4.835 ±0.001 0.1903 ±0.00004
* Finished dimensions (when hardened)

Drain Connection on A drain line ought to be used when pressure in the return line can exceed the
OMSS or Attached permissible pressure on the shaft seal of the attached component.
Component
The drain line can be connected at two different points:
1) at the motor drain connection
2) at the drain connection of the attached component.

If a drain line is fitted to the attached component, it must be possible for oil to flow freely
between motor and attached component.

The drain line must be led to the tank in such a way that there is no risk of the motor and
attached component being drained of oil when at rest.
The maximum pressure in the drain line is limited by the attached component and its
shaft seal.

520L0407 • Rev EK • Jun 2013 33

 OMT
Technical Information
Versions

OMT
Versions

Main type designation

High pressure release
Low pressure release
European version

Drain connection
Mounting flange

Check valve
US version
Port size
Shaft

Cyl. 40 mm G 3/4 l Yes Yes OMT

Cyl. 1.5 in 1 1/16-12 UN l Yes Yes OMT
G 3/4 l Yes Yes OMT
Standard Splined 1.5 in
1 1/16-12 UN l Yes Yes OMT
flange
Tapered 45 mm G 3/4 l Yes Yes OMT
Tapered 1.75 in 1 1/16-12 UN l Yes Yes OMT
P.t.o. G 3/4 l Yes Yes OMT
Cyl. 40 mm G 3/4 l Yes Yes OMTW
Wheel Tapered 45 mm G 3/4 l Yes Yes OMTW
Tapered 1.75 in 1 1/16-12 UN l Yes Yes OMTW
Wheel bolt flange G 3/4 l Yes No l OMT FX
Brake-wheel
Thread hole flange G 3/4 l Yes No l OMT FX
Cyl. 40 mm G 3/4 l Yes No l OMT FL
Brake- Splined 1.5 in G 3/4 l Yes No l OMT FL
standard Cyl. 40 mm G 3/4 l Yes No l OMT FH
Splined 1.5 in G 3/4 l Yes No l OMT FH
Short No output shaft G 3/4 l Yes Yes OMTS
Function diagram - see page : →

Features available (options) :

Speed sensor
Motor with tacho connection
Viton shaft seal
Painted
Ultra short

34 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Code Numbers

Code Numbers
Displacement [cm3]

Technical data – Page

Dimensions – Page
Shaft loads – Page
Code Numbers

160 200 250 315 400 500

151B 3000 3001 3002 3003 3004 3005 36 40 49
151B 2050 2051 2052 2053 2054 2055 36 40 50
151B 3006 3007 3008 3009 3010 3011 36 40 49
151B 2056 2057 2058 2059 2060 2061 36 40 50
151B 3012 3013 3014 3015 3016 3017 36 40 49
151B 2062 2063 2064 2065 2066 2067 36 40 50
151B 3018 3019 3020 3021 3022 3023 36 40 49
151B 3024 3025 3026 3027 3028 3029 36 40 51
151B 3030 3031 3032 3033 3034 3035 36 40 51
151B 2080 2081 2082 2083 2084 2085 36 40 52
151B 3207 3208 3209 3210 3211 3212 36 41 53
151B 3200 3201 3202 3203 3204 3205 36 41 53
151B 4000 4001 4002 4003 4004 4005 36 41 54
151B 4007 4008 4009 4010 4011 4012 36 41 54
151B 4021 4022 4023 4024 4025 4026 36 41 54
151B 4028 4029 4030 4031 4032 4033 36 41 54
151B 3036 3037 3038 3039 3040 3041 36 - 55
42 42 43 43 44 44

Ordering
Add the four digit prefix “151B” to the four digit numbers from the chart for complete
code number.

Example:
151B3002 for an OMT 250 with standard flange, cyl. 40 mm shaft and port size G 3/4.

Orders will not be accepted without the four digit prefix.

520L0407 • Rev EK • Jun 2013 35

 OMT
Technical Information
Technical Data

Technical data
for OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH
OMT OMT OMT OMT OMT OMT
OMTW OMTW OMTW OMTW OMTW OMTW
OMTS OMTS OMTS OMTS OMTS OMTS
Type
OMT FX OMT FX OMT FX OMT FX OMT FX OMT FX
OMT FL OMT FL OMT FL OMT FL OMT FL OMT FL
OMT FH OMT FH OMT FH OMT FH OMT FH OMT FH
Motor size 160 200 250 315 400 500
cm3 161.1 201.4 251.8 326.3 410.9 523.6
Geometric displacement
[in3] [9.83] [12.29] [15.37] [19.91] [25.07] [31.95]
min-1 cont. 625 625 500 380 305 240
Max. speed
[rpm] int1) 780 750 600 460 365 285
470 590 730 950 1080 1220
cont.
Nm [4160] [5220] [6460] [8410] [9560] [10800]
Max. torque
[lbf·in] 560 710 880 1140 1260 1370
int.1)
[4960] [6280] [7790] [10090] [11150] [12130]
26.5 33.5 33.5 33.5 30.0 26.5
cont.
kW [35.5] [44.9] [44.9] [44.9] [40.2] [35.5]
Max. output
[hp] 32.0 40.0 40.0 40.0 35.0 30.0
int.1)
[42.9] [53.6] [53.6] [53.6] [46.9] [40.2]
200 200 200 200 180 160
cont.
[2900] [2900] [2900] [2900] [2610] [2320]
bar 240 240 240 240 210 180
Max. pressure drop int.1)
[psi] [3480] [3480] [3480] [3480] [3050] [2610]
280 280 280 280 240 210
peak2)
[4060] [4060] [4060] [4060] [3480] [3050]
100 125 125 125 125 125
cont.
l/min [26.4] [33.0] [33.0] [33.0] [33.0] [33.0]
Max. oil flow
[USgal/min] 125 150 150 150 150 150
int.1)
[33.0] [39.6] [39.6] [39.6] [39.6] [39.6]
Max. starting pressure bar 10 10 10 10 10 10
with unloaded shaft [psi] [145] [145] [145] [145] [145] [145]
at max. press. drop cont. 340 430 530 740 840 950
Nm [lbf·in] [3010] [3810] [4690] [6550] [7430] [8410]
Min. starting torque
at max. press. drop int.1) 410 520 630 890 970 1060
Nm [lbf·in] [3630] [4600] [5580] [7880] [8590] [9380]
1) Intermittent operation: the permissible values may occur for max. 10% of every minute.
2) Peak load: the permissible values may occur for max. 1% of every minute.

For max. permissible combination of flow and pressure, see function diagram for actual motor.

36 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Technical Data

Technical data
for OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH
Max. return pressure
Type Max. inlet pressure
with drain line
bar 210 140
cont.
[psi] [3050] [2030]
OMT, OMTW,
bar 250 175
OMTS, OMT FX, int.1)
[psi] [3630] [2540]
OMT FL, OMT FH
bar 300 210
peak2)
[psi] [4350] [3050]

Brake motors
Max. presssure Holding Brake-release Max pressure
Type
in drain line3) torque4) pressure3) in brake line
OMT FX, 5 bar 1200 Nm 12 bar 30 bar
OMT FL [70 psi] [10620 lbf·in] [170 psi] [440 psi]
5 bar 1200 Nm 30 bar 280 bar
OMT FH
[70 psi] [10620 lbf·in] [440 psi] [4060 psi]
1) Intermittent operation: the permissible values may occur for max. 10% of every minute.
2) Peak load: The permissible values may occur for max. 1% of every minute.
3) Brake motors must always have a drain line. The brake-release pressure is the difference between the pressure in the brake line and the
pressure in the drain line.
4) For the supply of motors with holding torques higher than those stated, please contact the Sauer-Danfoss Sales Organization.

For max. permissible combination of flow and pressure, see function diagram for actual motor.

520L0407 • Rev EK • Jun 2013 37

 OMT
Technical Information
Technical Data

Max. Permissible Shaft OMT with check valves OMT with check valves
Seal Pressure and without use of and with drain connection:
drain connection: The shaft seal pressure equals
The pressure on the shaft seal the pressure on the drain line.
never exceeds the pressure in
the return line 151-320.10

OMT FX, OMT FL and OMT FH

must always be fitted with
drain line.
Max. pressure in drain line is
5 bar [75 psi]

151-1405.10

Max. return pressure without drain line or max. pressure in the drain line
P P
psi bar
1500
100
90
1200
80
70
900
60
50
600 40
30
300 20
10
0 0
0 100 200 300 400 500 600 700 800 max. min-1
(rpm)

151-1674.10

– – – – Intermittent operation: the permissible values may occur for max. 10% of every minute.

Continuous operation

38 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Technical Data

Pressure Drop in Motor ∆p ∆p

psi bar
16

200 14

12
150 10

8
100
6

4
50
2

0 0 Q
0 20 40 60 80 100 120 140 l/min

Q
0 4 8 12 16 20 24 28 32 36 US gal/min

151-1409.10

The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]

Oil Flow in Drain Line The table shows the max. oil flow in the Pressure Viscosity Oil flow in
drop drain line
drain line at a return pressure less than
bar mm2/s l/min
5-10 bar [75-150 psi]. [psi] [SUS] [US gal/min]
20 2.5
140 [100] [0.66]
[2030] 35 1.5
[165] [0.40]
20 5.0
210 [100] [1.32]
[3050] 35 3.0
[165] [0.79]

Direction of Shaft B A B A
Rotation

151-1050.10

520L0407 • Rev EK • Jun 2013 39

 OMT
Technical Information
Technical Data

Permissible Shaft Loads Mounting flange: Shaft:

for OMT Standard All shaft types
Prad. Prad.
lbf N
14000
60000
0
- +
12000 Pmax. =10000 N
50000 =2248 lbf

10000
40000
8000
30000
6000

20000
4000

2000 10000

0 0
-60 -40 -20 0 20 40 60 80 100 120 140 mm

-2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 in

151-1967.10

Mounting flange: Shaft:

Wheel All shaft types
Prad. Prad.
lbf N
14000
60000
0 Pmax. =10000 N
12000 - +
=2248 lbf
50000
10000
40000
8000
30000
6000

20000
4000

2000 10000

0 0
0 20 40 60 80 100 120 140 160 mm

0 1 2 3 4 5 6 in
151-1970.10

The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of
the distance from the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at
100 min-1) at rated output torque, when mineral-based hydraulic oil with a sufficient
content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown
in the curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the
chapter "Bearing dimensioning" in the technical information "General Orbital motors"
520L0232.

40 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Technical Data

Permissible Shaft Loads Mounting flange: Shaft:

for OMT Brake-wheel All shaft types
Prad. Prad.
lbf N

5500 25000
0 Pmax. =5000 N
5000 - + =1124 lbf

4500 20000
4000 Pmax. =7000 N
=1574 lbf
3500 15000
3000
2500
10000
2000
1500
5000
1000
500
0 0
0 20 40 60 80 100 120 140 mm

0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 in

151-1966.10

Mounting flange: Shaft:

Brake-standard All shaft types
Prad. Prad.
lbf N
14000
60000
0
- +P
12000 max. =10000 N
50000 =2248 lbf

10000
40000
8000
30000
6000

20000
4000

2000 10000

0 0
-80 -60 -40 -20 0 20 40 60 80 100 120 mm

-3 -2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 in

151-1968.10

The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of
the distance from the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at
100 min-1) at rated output torque, when mineral-based hydraulic oil with a sufficient
content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown
in the curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the
chapter "Bearing dimensioning" in the technical information "General Orbital motors"
520L0232.

520L0407 • Rev EK • Jun 2013 41

 OMT
Technical Information
Function Diagrams

Function Diagrams
OMT 160

Q=10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

40 l/min
[10.6 US gal/min]

60 l/min
[15.9 US gal/min]

80 l/min
[21.1 US gal/min]

100 l/min
[26.4 US gal/min]

Q=125 l/min
[33.0 US gal/min]
lbf•in Nm

5500
600
5000
550 ∆ p=240 bar
3480 psi
4500 500 N=35kW

4000 450 200 bar

35hp 30kW 2900 psi
3500 400
25kW
160 bar
350
3000 30hp 2320 psi
300 25hp 20kW
2500
120 bar
250 20hp 1740 psi
2000 ηt =86% 15kW
200
10kW 15hp
1500 10hp 80 bar
150 85%
N=5kW 1160 psi
1000 5hp
100
∆ p= 40 bar
500 50 80%
580 psi
ηt =70%
0 0

0 100 200 300 400 500 600 700 800 min-1

(rpm)

151-493.10

OMT 200
lbf•in Nm
Q=10 l/min
[2.6 US gal/min]

20 l/min
[5.3 US gal/min]

40 l/min
[10.6 US gal/min]

60 l/min
[15.9 US gal/min]

80 l/min
[21.1 US gal/min]

100 l/min
[26.4 US gal/min]

125 l/min
[33.0 US gal/min]

Q=150 l/min
[39.6 US gal/min]
750
6500
700
6000 ∆ p=240 bar
650 35kW N=40kW 3480 psi
5500
600 30kW
5000 550 200 bar
25kW 2900 psi
4500 500 35hp
20kW 40hp
4000 450 160 bar
15kW 25hp 30hp 2320 psi
3500 400
10kW 15hp 20hp 87%
3000 350
10hp 120 bar
300
2500 N=5kW ηt =88% 1740 psi
250 85%
2000
200 5hp 80 bar
1500 1160 psi
150
80%
1000 100
ηt =70% ∆ p= 40 bar
500 50
580 psi
0 0

0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 min-1
(rpm)

151-494.10

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Intermittent pressure drop and oil flow must not occur simultaneously.

42 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Function Diagrams

Function Diagrams
OMT 250

Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]

40 l/min
[10.6 US gal/min]

60 l/min
[15.9 US gal/min]

80 l/min
[21.1 US gal/min]

100 l/min
[26.4 US gal/min]

125 l/min
[33.0 US gal/min]

Q=150 l/min
[39.6 US gal/min]
lbf•in Nm

9000

8000 900
∆ p=240 bar
7000 800 3480 psi
35kW N=40kW
30kW
700 200 bar
6000
40hp 2900 psi
600 25kW 35hp
5000
20kW 30hp 160 bar
500 2320 psi
4000 15kW 25hp
400 20hp 120 bar
15hp 1740 psi
3000 10kW
ηt =87%
300
N=5kW 80 bar
2000 10hp 85%
200 1160 psi
5hp 80%
1000 100 ∆ p= 40 bar
ηt =70% 580 psi
0 0

0 50 100 150 200 250 300 350 400 450 500 550 600 min-1
(rpm)

151-495.10

OMT 315
lbf•in Nm
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]

40 l/min
[10.6 US gal/min]

60 l/min
[15.9 US gal/min]

80 l/min
[21.1 US gal/min]

100 l/min
[26.4 US gal/min]

125 l/min
[33.0 US gal/min]

Q=150 l/min
[39.6 US gal/min]
11000
1200
10000
1100 ∆ p=240 bar
9000 3480 psi
1000 35kW N=40kW
8000 900 200 bar
30kW
800 25kW 2900 psi
7000
40hp
700 20hp 20kW 160 bar
6000 15kW 30hp 35hp 2320 psi
15hp 25hp
600
5000
120 bar
500 10kW
4000 1740 psi
10hp
400
3000 5hp N=5kW 80 bar
300 87%
ηt =88% 1160 psi
2000
200
1000
85% 80% ∆ p= 40 bar
100
ηt =70% 580 psi
0 0

0 50 100 150 200 250 300 350 400 450 500 min-1
(rpm)

151-869.10

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Intermittent pressure drop and oil flow must not occur simultaneously.

520L0407 • Rev EK • Jun 2013 43

 OMT
Technical Information
Function Diagrams

Function Diagrams
OMT 400

Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]

40 l/min
[10.6 US gal/min]

80 l/min
[21.1 US gal/min]

100 l/min
[26.4 US gal/min]

125 l/min
[33.0 US gal/min]

Q=150 l/min
[39.6 US gal/min]
60 l/min
[15.9 US gal/min]
lbf•in Nm

12000
1300
11000
1200 ∆ p=210 bar
10000 3050 psi
1100
9000 1000 180 bar
2610 psi
8000 900 N=30kW
25kW 150 bar
7000 800 2180 psi
20kW
700
6000 15kW 120 bar
10kW 25hp 30hp 1740 psi
600 10hp
5000 87%
20hp
500
4000 5kW
ηt =89% 15hp 90 bar
5hp 1300 psi
400 85%
3000
300 60 bar
2.5hp 80% 870 psi
2000 200 N=2.5kW

1000 100 ∆ p= 30 bar

ηt =70% 440 psi
0 0

0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 min-1
(rpm)

151-1058.10

OMT 500
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]

40 l/min
[10.6 US gal/min]

80 l/min
[21.1 US gal/min]

100 l/min
[26.4 US gal/min]

125 l/min
[33.0 US gal/min]

Q=150 l/min
[39.6 US gal/min]
60 l/min
[15.9 US gal/min]

lbf•in Nm

1500
12500
∆ p=180 bar
1250 2610 psi

10000 160 bar

30hp N=30kW 2320 psi
1000 140 bar
20kW 25kW 2030 psi
7500 15kW 25hp 120 bar
10hp 10kW 1740 psi
750 20hp
ηt =90% 15hp 90 bar
5000 5kW 1300 psi
500
N=2.5kW 5hp
60 bar
2.5hp 87% 870 psi
2500 85%
250
ηt =80% ∆ p= 30 bar
440 psi
0 0

0 25 50 75 100 125 150 175 200 225 250 275 300 min-1
(rpm)

151-1116.10

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Intermittent pressure drop and oil flow must not occur simultaneously.

44 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Shaft Version

Shaft Version 82 [3.23]

26 [1.02]
9.5 [0.374]
45˚
R0.5 [0.020] M12
A-A
A

Ø40.018 [1.5755]
Ø40.002 [1.5749]
A: Cylindrical 40 mm shaft

43.00 [1.693]
42.71 [1.681]
Ø45 [1.77]
C: Parallel key
A
A12 × 8 × 70
DIN 6885
Keyway deviates from
standard C
A

70.5 [2.776] 5.5 [0.217]
70.0 [2.756] 4.5 [0.177]
12.000 [0.4724]
11.957 [0.4707]

82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]
45˚
R0.5 [0.020] 3/8 -16 UNC
A-A
A
B: Cylindrical 1.5 in shaft
D: Parallel key
3/8 × 3/8 × 21/4 in
Ø38.10 [1.500]
Ø38.05 [1.498]

42.40 [1.669]
42.14 [1.659]
Ø45 [1.77]

B.S. 46
B
Keyway deviates from
standard

A D
57.5 [2.264] 11.5 [0.453]
56.9 [2.240] 9.3 [0.366]
9.545 [0.3758]
9.525 [0.3750]

151-1032.10

520L0407 • Rev EK • Jun 2013 45

 OMT
Technical Information
Shaft Version

Shaft Version 82 [3.23]

26 [1.02]
9.5 [0.374]
45˚
R0.5 [0.020] M12
C. Involute splined shaft A-A
A
ANS B92.1 - 1970 standard
Flat root side fit

Ø38.100 [1.5000]
Ø38.075 [1.4990]
Pitch 12/24
Ø45 [1.77]

Teeth 17 C
Major dia. 1.50 in
Pressure angle 30°

A
58 [2.28]
56 [2.20]

82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]
45˚
R0.5 [0.020] 3/8 -16 UNC
US version A A-A
D. Involute splined shaft
ANS B92.1 - 1970 standard
Ø38.100 [1.5000]
Ø38.075 [1.4990]

Flat root side fit

Ø45 [1.77]

Pitch 12/24 D
Teeth 17
Major dia. 1.50 in
Pressure angle 30°
A
58 [2.28]
56 [2.20]

151-1916.10

46 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Shaft Version

Shaft Version
I A-A
H
A
E: Tapered 45 mm shaft
(ISO/R775)
I: DIN 937

Ø56 [2.20]
Ø45 [1.77]

Ø6 [0.24]

Ø7 [0.28]
M30x2
Across flats: 46 mm E

24.15 [0.951]
23.95 [0.943]
Tightening torque:
500 ± 30 Nm [4430 ±270 lbf·in]
H: Taper 1:10
J: Parallel key A J
B12 × 8 × 28 34 [1.34] 4 [0.16]
DIN 6885 12.000 [0.4724]
54 [2.13] 22 [0.87]
Keyway deviates from 11.957 [0.4707]
standard 82 [3.23]

16 [0.63]
A-A
K L
F: Tapered 1.75 in shaft A
K: Cone 1:8
SAE J501
L: 1 1/4 - 18 UNEF
Ø45 [1.77]

Ø4 [0.16]
Across flats 2 3/16 in F
Tightening torque:

5.71 [0.225]
5.61 [0.221]
500 ±10 Nm (4425 ±90 lbf·in)
M: Parallel key
7
/16 × /16 × 1 /4
7 1 M
A
B.S. 46 32.1 [1.264]
Keyway deviates from 31.5 [1.240]
59.00 [2.323] 11.150 [0.4390]
standard 11.130 [0.4382]
57.80 [2.276]

4.5 [0.177]

80.8 [3.181]
80.0 [3.150]

102 [4.02]

45˚ R0.5 [0.020] R6.7 [0.267]

G. P.t.o. shaft R5 [0.20]
60˚
DIN 9611 Form 1 A A-A
8.6 3 [0.3
8.5

(ISO/R500 without pin hole)

4[
0.3 36]
40
Ø34.85 [1.372]
Ø34.73 [1.367]

]
29.5 [1.161]
29.3 [1.154]
Ø45 [1.77]

** Deviates from DIN 9611

G

28.14 [1.108]**
A 7 [0.28]
27.89 [1.098]
38.25 [1.506]
37.75 [1.486]
77 [3.03]
75 [2.95]

151-1917.10

520L0407 • Rev EK • Jun 2013 47

 OMT
Technical Information
Technical Data

Port Thread Versions B

A Ø41.5 [1.634]
Ø41.0 [1.614]
E F

min. 18 [0.67]

min. 19 [0.75]
A: G main ports B: UN main ports
E: ISO 228/1 - G3/4 F: 1 1/16 - 12 UN
O-ring boss port
C D

G H

min. 13 [0.51]
min. 12 [0.47]

151-1977.11

C: G drain port D: UNF drain port

G: ISO 228/1 - G1/4 H: 9/16 - 18 UNF
O-ring boss port

48 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Dimensions – European Version

Dimensions Ø125.000 [4.9213]

Ø124.937 [4.9188]
Standard Flange Ø123.8 [4.874]
Ø122.2 [4.811]
Ø73 [2.87]
Ø71 [2.80]

L3

22.4 [0.882]

R1.6 [0.063]
9 [0.35]
32 [1.26]

31 [1.22]
60 [2.36]

72 [2.83]

18 [0.71]
64 [2.52]
L2
13.0 [0.512]
12.0 [0.472]
L

L1

D
C
13.0 [0.512]
12.0 [0.472]

max. 69 [2.72]
13.0 [0.512]
12.0 [0.472]
23.6 [0.929]
22.4 [0.882]

13.0 [0.512]
12.0 [0.472]

22.1 [0.870] 22.1 [0.870] max. 67 [2.64] max. 71 [2.80]

21.1 [0.831] 21.1 [0.831]
20.3 [0.799] 20.3 [0.799] E
19.7 [0.776] 19.7 [0.776]
22.1 [0.870] 22.1 [0.870]
21.1 [0.831] 21.1 [0.831]
100 [3.94]
max. 128 [5.04]
Ø14 [0.55]
max. 143 [5.63]

28 ]
[6. .315
3]
59 [6
Ø1 60.4

Lmax L1* L2 L3
.6
R12 [0.47]

Ø1

Type mm mm mm Output shaft mm

[in] [in] [in] [in]
190 16.5 140 All shafts except 82
OMT 160 max.
[7.48] [0.650] [5.51] P.t.o. shaft [3.23] max. 143 [5.63]
195 21.5 145 102
OMT 200 P.t.o. shaft max.
[7.68] [0.846] [5.71] [4.02]
201 27.8 151 C: Drain connection
OMT 250
[7.91] [1.094] [5.94] G 1⁄4; 12 mm [0.47 in] deep 151-889.11

211 37.0 161 D: M10; 10 mm [0.39 in] deep

OMT 315
[8.31] [1.457] [6.34] E: G 3⁄4; 17 mm [0.67 in] deep
221 47.5 171
OMT 400 *) The gearwheel set is 3.5 mm
[8.70] [1.870] [6.73]
235 61.5 185 [0.138 in] wider across the
OMT 500 rollers than the L1 dimensions
[9.25] [2.421] [7.28]

520L0407 • Rev EK • Jun 2013 49

 OMT
Technical Information
Dimensions – US Version

Standard Flange Ø127.00 [5.000]

Ø126.95 [4.998]
Ø123.8 [4.874]
Ø122.2 [4.811]
Ø86.5 [3.406]
Ø85.5 [3.366]
33.15 [1.305]
30.85 [1.215]
L3

22.4 [0.882]

R0.8 [0.003]
9 [0.35]

31 [1.22]
60 [2.36]

73.7 [2.902]
18 [0.71] 71.5 [2.815]
64.5 [2.539]
63.5 [2.500]
L2
L

L1

max. 69 [2.72]
23.6 [0.929]
22.4 [0.882]

20.3 [0.799] 20.3 [0.799] max. 67 [2.64] max. 75 [2.95]

D
19.7 [0.776] 19.7 [0.776]
100 [3.94]
max. 128 [5.04]
Ø14 [0.55]
max. 143 [5.63]

35 ]
[6. .390
8]
61 3 [6
R12.5 [0.492]

Lmax L1* L2 L3
Ø1 62.
.5
Ø1

Type mm mm mm Output shaft mm

[in] [in] [in] [in]
190 16.5 140 Cyl. 1.5 in 82
OMT 160
[7.48] [0.650] [5.51] Splined 1.5 in [3.23] max. 143 [5.63]

195 21.5 145 80.4

OMT 200 Tapered 1.75 in
[7.68] [0.846] [5.71] [3.17]
201 27.8 151 C: Drain connection 9⁄16 - 18
OMT 250
[7.91] [1.094] [5.94] UNF; 13 mm [0.51 in] deep 151-889.11.22

211 37.0 161 O-ring boss port

OMT 315
[8.31] [1.457] [6.34] D: 1 1⁄16 - 12 UN; 19 mm [0.75 in]
221 47.5 171 deep O-ring boss port
OMT 400
[8.70] [1.870] [6.73]
235 61.5 185 *) The gearwheel set is 3.5 mm
OMT 500 [0.138 in] wider across the
[9.25] [2.421] [7.28]
rollers than the L1 dimensions

50 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Dimensions – European Version

Wheel Ø172.000 [6.7717]

Ø171.937 [6.7692]
Ø160.000 [6.2992]
Ø159.937 [6.2967]
Ø126.25 [4.970]
Ø123.75 [4.872]
Ø123.8 [4.874]
Ø122.2 [4.811]
Ø73 [2.87]
Ø71 [2.80]
82 [3.23]

2 [0.08]x45˚

98.2 [3.866]
99 [3.90]

90.3 [3.555]
78.2 [3.079]

R1.2 [0.047]
45˚
7 [0.28]

8 [0.31]
18 [0.71]
13.0 [0.512]
12.0 [0.472]
L1
L2

R1.2 [0.047]
4 [0.16]

13.0 [0.512]
12.0 [0.472]

C
L

max. 69 [2.72]
D
13.0 [0.512]
12.0 [0.472]

23.6 [0.929]
22.4 [0.882]

13.0 [0.512]
12.0 [0.472]

22.1 [0.870] 22.1 [0.870]

E max. 67 [2.64] max. 71 [2.80]
21.1 [0.831] 21.1 [0.831] 75 [2.95]
20.3 [0.799] 20.3 [0.799]
19.7 [0.776] 19.7 [0.776]
22.1 [0.870] 22.1 [0.870]
21.1 [0.831] 21.1 [0.831]
100 [3.94]
max. 128 [5.04]
Ø18 [0.71]

Lmax L1* L2
max. 180 [7.09]

Type mm mm mm
[in] [in] [in]
85 ]
[7. .890

OMTW 123 16.5 73

8]
99 [7

160 [4.84] [0.650] [2.87]

Ø1 00.4
.6
Ø2

OMTW 128 21.5 78

R16 [0.63]

200 [5.04] [0.846] [3.07]

C: Drain connection
OMTW 134 27.8 84 G 1⁄4; 12 mm [0.47 in] deep
250 [5.28] [1.094] [3.31] D: M10; 10 mm [0.39 in] deep
max. 180 [7.09]
OMTW 144 37.0 94 E: G 3⁄4; 17 mm [0.67 in] deep
315 [5.67] [1.457] [3.70]
OMTW 154 47.5 104 *) The gearwheel set is 3.5 mm
400 [6.06] [1.870] [4.09] [0.138 in] wider across the 151-897.12
OMTW 168 61.5 118 rollers than the L1 dimensions
500 [6.61] [2.421] [4.65]

520L0407 • Rev EK • Jun 2013 51

 OMT
Technical Information
Dimensions – US Version

Wheel Ø172.000 [6.7717]

Ø171.937 [6.7692]
Ø160.000 [6.2992]
Ø159.937 [6.2967]
Ø126.25 [4.970]
Ø123.75 [4.872]
Ø123.8 [4.874]
Ø122.2 [4.811]
Ø73 [2.87]
Ø71 [2.80]
80.8 [3.181]
80.0 [3.150]

2 [0.08]x45˚
102.1 [4.020]
99.1 [3.902]

98.2 [3.866]
90.3 [3.555]
78.6 [3.094]
77.5 [3.051]

R1.2 [0.047]

45˚
7 [0.28]

7 [0.28]
18 [0.71]
L1
L2

3.5 [0.138]

R1.2 [0.047]

C
L

max. 69 [2.72]
23.6 [0.929]
22.4 [0.882]

D max. 67 [2.64] max. 75 [2.95]

20.3 [0.799] 20.3 [0.799]
19.7 [0.776] 19.7 [0.776] 75 [2.95]
100 [3.94]
max. 128 [5.04]
Ø18 [0.71]

Lmax L1* L2
max. 180 [7.09]

Type mm mm mm
[in] [in] [in]
85 ]

OMTW 123 16.5 73

[7. .890
8]
99 4 [7

160 [4.84] [0.650] [2.87]

Ø1 00.
.6
Ø2

OMTW 128 21.5 78

R16 [0.63]

C: Drain connection
200 [5.04] [0.846] [3.07] 9⁄16 - 18 UNF;
OMTW 134 27.8 84 13 mm [0.51 in] deep
250 [5.28] [1.094] [3.31] O-ring boss port
OMTW 144 37.0 94 D: 1 1⁄16 - 12 UN; max. 180 [7.09]

315 [5.67] [1.457] [3.70] 19 mm [0.75 in] deep

OMTW 154 47.5 104 O-ring boss port
400 [6.06] [1.870] [4.09]
151-897.11.22
OMTW 168 61.5 118 *) The gearwheel set is 3.5 mm
500 [6.61] [2.421] [4.65] [0.138 in] wider across the
rollers than the L1 dimensions

52 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Dimensions – European Version

Brake-Wheel

m
ax
Ø

.2
Ø1 200

32
75 [2.95]
99 .4

[9
.6 [7.8

. 13
F [7 9

]
.8 0]
58
]

71 [2.80]
C

Ø22 [0.87]
67 [2.64]

Ø201 [7.91]
Ø180.00 [7.087] Ø120.0 [4.724]

12.2 [0.480]
11.8 [0.465]

13.2 [0.520]
12.8 [0.504]
Ø179.6 [7.074]

5.2 [0.205]
4.8 [0.189]

4.2 [0.165]
3.8 [0.150]
Ø119.6 [4.709]
H Ø95.8 [3.772] Ø76.0 [2.992]
Ø95.6 [3.764] Ø75.8 [2.984]
G
35 [1.38]

111.4 [4.386]
110.6 [4.354]
115.4 [4.543]
114.6 [4.512]
10.2 [0.402]
9.8 [0.386]
7.2 [0.283]
6.8 [0.268]

L max. 1
L max. 2
E D L1
L2

I
13 [0.51]
12 [0.47]

11.1 [0.437]
10.9 [0.429]
23.3 [0.917]
22.7 [0.894]
13 [0.51]
12 [0.47]

23.1 [0.909]
22.9 [0.902]
Lmax 1 Lmax 2 L1* L2 20.3 [0.799] 20.3 [0.799]
Type mm mm mm mm 19.7 [0.776] 19.7 [0.776]
22.1 [0.870] 22.1 [0.870]
[in] [in] [in] [in] 21.1 [0.831] 21.1 [0.831]
100 [3.94]
OMT 223 227 16.5 62 128 [5.04]
160 FX [8.78] [8.94] [0.650] [2.45] Ø172.00 [6.772]
Ø171.94 [6.769]
OMT 228 232 21.5 67
200 FX [8.98] [9.13] [0.846] [2.65]
OMT 234 238 27.8 74
250 FX [9.21] [9.37] [1.094] [2.89]
OMT 243 247 37.0 83
315 FX [9.57] [9.72] [1.457] [3.26]
10x36˚
5x72˚
4x90˚

OMT 254 258 47.5 93

400 FX [10.00] [10.16] [1.870] [3.67]
OMT 268 272 61.5 107
500 FX [10.55] [10.71] [2.421] [4.22]
Ø140.0 [5.512] Ø100.0 [3.937]
Ø139.6 [5.496] Ø99.6 [3.921]
C: Brake-release port G 1/4;
12 mm [0.47 in] deep (BS/ISO 228/1)
D: Drain connection G 1/4;
12 mm [0.47 in] deep 151-1443.11
E: G 3/4; 17 mm [0.67 in] deep
F: 4 × M12; 27 mm [1.06 in] deep
G: 10 × M12
H: Wheel bolts 5 × M14 × 1.5
I: M10; 10 mm [0.39 in] deep
*) The gearwheel set is 3.5 mm
[0.138 in] wider across the rollers than
the L1 dimensions

520L0407 • Rev EK • Jun 2013 53

 OMT
Technical Information
Dimensions – European Version

Brake-Standard Ø125.000 [4.9213]

Ø124.937 [4.9188]
Ø123.5 [4.862]
Ø122.5 [4.823]
Ø86.2 [3.406]
12 [0.47]
Ø85.5 [3.366]

31.5 [1.240]
82 [3.23]

R1.6 [0.063]

12 [0.47]
18 [0.71]
60 [2.36]
32 [1.26]

104 [4.09]
85.8 [3.378]

90.5 [3.563]

E L2
L

D
F
L1
13.0 [0.512]
12.0 [0.472]

C
23.6 [0.929]
22.4 [0.882]
13.0 [0.512]
12.0 [0.472]
13.0 [0.512]
12.0 [0.472]

13.0 [0.512]
12.0 [0.472]

max. 67 [2.64] max. 71 [2.80]

22.1 [0.870] 22.1 [0.870]
21.1 [0.831] 21.1 [0.831]
20.3 [0.799] 20.3 [0.799]
19.7 [0.776] 19.7 [0.776]
22.1 [0.870] 22.1 [0.870] max. 171 [6.73]
21.1 [0.831] 21.1 [0.831]
Ø160.4 [6.315]
100 [3.94] Ø159.6 [6.283]
max. 128 [5.04] max. 147.3 [5.799]
max. 147.3 [5.799]

max. 170 [6.69]

Ø14 [0.55]

Lmax L1* L2
Type mm mm mm
[in] [in] [in]
OMT 160 228 16.5 178
FL/FH [8.98] [0.650] [7.01] max. Ø187 [7.36]
C: G 3/4; 17 mm [0.67 in] deep
OMT 200 233 21.5 183 (BS/ISO 228/1)
FL/FH [9.17] [0.846] [7.20] D: Drain connection
OMT 250 239 27.8 189 G 3/8; 14 mm [0.55 in] deep
151-1453.10
FL/FH [9.41] [1.094] [7.44] E: Brake-release port G 1/4;
OMT 315 248 37.0 199 12 mm [0.47 in] deep
FL/FH [9.76] [1.457] [7.83] F: M10; 10 mm [0.39 in] deep
OMT 400 259 47.5 209
FL/FH [10.20] [1.870] [8.23] *) The gearwheel set is 3.5 mm
[0.138 in] wider across the
OMT 500 273 61.5 223
rollers than the L1 dimensions
FL/FH [10.75] [2.421] [8.78]

54 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
Dimensions – European Version

Short
max. Ø186 [7.32]
Ø125.000 [4.9213]
28 [1.10]

1 [0.04]x45˚
Ø124.937 [4.9188]
8 [0.31]

R1 [0.04]
Ø14 [0.55]

22 [0.87]
31 [1.22]
18 [0.71]
L2

13 [0.512]
12 [0.472]
L1

8 [0.31]

13 [0.512]
12 [0.472]
L

max. 69 [2.72]
13 [0.512]
12 [0.472]

D
23.6 [0.926]
22.4 [0.882]

13 [0.512]
12 [0.472]

22.1 [0.870] 22.1 [0.870] max. 67 [2.64] max. 71 [2.80]

21.1 [0.831] 21.1 [0.831] E
20.3 [0.799] 20.3 [0.799]
19.7 [0.776] 19.7 [0.776] 42 [1.65] 50 [1.97]
22.1 [0.870] 22.1 [0.870] Ø6 [0.24]
21.1 [0.831] 21.1 [0.831]
100 [3.94]
max. 128 [5.04]

28 [1.10]
Ø16
Ø15 0.4 [6.3
9.6 1
[6.2 5]
83]

Ø6 [0.24]

151-898.11

Lmax L1* L2
Type mm mm mm
[in] [in] [in]
OMTS 146 16.5 96
160 [5.75] [0.650] [3.78]
OMTS 151 21.5 101
200 [5.94] [0.846] [3.98]
C: Drain connection
OMTS 157 27.8 107 G 1⁄4; 12 mm [0.47 in] deep
250 [6.18] [1.094] [4.21] D: M10; 10 mm [0.39 in] deep E:
OMTS 166 37.0 116 G 3⁄4; 17 mm [0.67 in] deep
315 [6.54] [1.457] [4.57]
OMTS 177 47.5 127 *) The gearwheel set is 3.5 mm
400 [6.97] [1.870] [5.00] [0.138 in] wider across the
OMTS 191 61.5 142 rollers than the L1 dimensions
500 [7.52] [2.421] [5.59]

520L0407 • Rev EK • Jun 2013 55

 OMT
Technical Information
OMTS

Installing the OMTS The cardan shaft of the OMTS motor acts as an “output shaft”. Because of the movement
of the shaft, no seal can be fitted at the shaft output.
Internal oil leakage from the motor will therefore flow into the attached component.

During start and operation it is important that the spline connection and the bearings
in the attached component receive oil and are adequately lubricated. To ensure that the
spline connection receives sufficient oil, a conical sealing ring between the shaft of the
attached component and the motor intermediate plate is recommended. This method is
used in the OMT.

The conical sealing ring (code. no. 633B9022) is supplied with the motor.

To ensure that oil runs to the bearings and other parts of the attached component, the
stop plate must have a hole in it (see fig. below).

We recommend an O-ring between motor and attached component. The O-ring

(code no. 151B1040) is supplied with the motor. If motor and attached component have
been separated, remember to refill before starting up. Fill the oil through the drain
connection.

F
OMTS 2.35 [0.093]
2.25 [0.089]
Dimensions of the A C
Attached Component
B

K 0.25 [0.010]
Ø88.5 [3.484]
Ø87.5 [3.445]

K 0.1˚
Ø125.063 [4.9237]
Ø125.000 [4.9212]

Ø133.0 [5.236]
Ø132.6 [5.220]
min. Ø55 [2.17]

Ø53.5 [2.106]
Ø53.5 [2.098]
min. Ø6 [0.24]

Ø63.5 [2.500]
Ø62.5 [2.461]
K
39.5 [1.555]
38.5 [1.516]

Ø51.5 [2.028]
Ø50.5 [1.988]

G
H D
E
2.5 [0.098] min. 5 [0.2] 8.2 [0.323]
1.5 [0.059] 7.8 [0.307]
18.5 [0.728]
25.5 [1.004] 17.5 [0.689]
24.5 [0.965]
11.4 [0.449] 30 [1.181]
11.0 [0.433] 29 [1.142]
46.3 [1.823]
45.7 [1.799]
69.4 [2.732]
68.6 [2.701]

151-452.10

A: O-ring: 125 × 3 mm E: Internal drain channel

B: External drain channel F: M12; min. 18 mm [0.71 in] deep
C: Drain connection G: Oil circulation hole
G 1⁄4; 12 mm [0.47 in] deep H: Hardened stop plate
D: Conical seal ring

56 520L0407 • Rev EK • Jun 2013

 OMT
Technical Information
OMTS

Internal Spline Data for The attached component must have internal splines corresponding to the external
the Component to be splines on the motor cardan shaft (see drawing below).
Attached
Material:
Case hardening steel with a tensile strength corresponding at least to 20 MoCr4
(900 N/mm2) or SAE 8620.

Hardening specification:
•• On the surface: HV = 750 ± 50
•• 0.7 ± 0.2 mm under the surface: HV = 560

Internal involute spline data

Standard ANS B92.1-1970, class 5 (corrected m · X = 1; m = 2.1166)

Flat root side fit mm in

Number of
z 16 16 Rmin
teeth
Pitch DP 12/24 12/24
Pressure angle 30° 30°
Lo
Pitch dia. D 33.8656 1.3333
Major dia. Dri 38.4 +0.4 1.5118 +0.0157 So
0 0
Form dia.
Dfi 37.6 1.4803
(min.) l d
Minor dia. Di 32.150 + 0.04
0
1.2657 +0 0.00157 Dri
Space width Di
Lo 4.516 ±0.037
0.1777 ±0 .0014 Dfi
(circular)
Tooth thickness D
So 2.170 0.0854
(circular)
Fillet radius Rmin. 0.5 0.02
Max.
measurement l 26.9 +0 0.1 1.059 +0.004
0
151-455.10
between pins*
Pin dia. d 4.834 ±0.001
0.1903 ±0.00004

* Finished dimensions (when hardened)

Drain Connection on A drain line ought to be used when pressure in the return line can exceed the
OMTS or Attached permissible pressure on the shaft seal of the attached component.
Component
The drain line can be connected at two different points:
1) at the motor drain connection
2) at the drain connection of the attached component.
If a drain line is fitted to the attached component, it must be possible for oil to flow freely
between motor and attached component.

The drain line must be led to the tank in such a way that there is no risk of the motor and
attached component being drained of oil when at rest.
The maximum pressure in the drain line is limited by the attached component and its
shaft seal.

520L0407 • Rev EK • Jun 2013 57

 OMV
Technical Information
Versions

OMV
Versions

Main type designation

European version

Drain connection
Mounting flange

Check valve
US version
Port size
Shaft

Cyl. 50 mm G1 l Yes Yes OMV

Cyl. 2.25 in 1 5/16-12 UN l Yes Yes OMV
Standard G1 l Yes Yes OMV
Splined 2.125 in
flange 1 5/16-12 UN l Yes Yes OMV
Tapered 60 mm G1 l Yes Yes OMV
Tapered 2.25 in 1 5/16-12 UN l Yes Yes OMV
Cyl. 2.25 in 1 5/16-12 UN l Yes Yes OMV
SAE-C flange
Splined 2.125 in 1 5/16-12 UN l Yes Yes OMV
Cyl. 50 mm G1 l Yes Yes OMVW
Wheel Tapered 60 mm G1 l Yes Yes OMVW
Tapered 2.25 in 1 5/16-12 UN l Yes Yes OMVW
Short No output shaft G1 l Yes Yes OMVS
Function diagram - see page : →

Features available (options) :

Speed sensor
Motor with tacho connection
Viton shaft seal
Painted
Ultra short

58 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
Code Numbers

Code Numbers
Displacement [cm3]

Technical data – Page

Dimensions – Page
Shaft loads – Page
Code Numbers

315 400 500 630 800

151B 3100 3101 3102 3103 3104 60 63 72
151B 2150 2151 2152 2153 2154 60 63 73
151B 3105 3106 3107 3108 3109 60 63 72
151B 2155 2156 2157 2158 2159 60 63 73
151B 3110 3111 3112 3113 3114 60 63 72
151B 2160 2161 2162 2163 2164 60 63 73
151B 2183 2184 2185 2186 2187 60 64 74
151B 2188 2189 2190 2191 2192 60 64 74
151B 3115 3116 3117 3118 3119 60 63 75
151B 3120 3121 3122 3123 3124 60 63 75
151B 2170 2171 2172 2173 2174 60 63 76
151B 3125 3126 3127 3128 3129 60 - 77
65 65 66 66 67

Ordering
Add the four digit prefix “151B” to the four digit numbers from the chart for complete
code number.

Example:
151B3101 for an OMV 400 with standard flange, cyl. 50 mm shaft and port size G 1.

Orders will not be accepted without the four digit prefix.

520L0407 • Rev EK • Jun 2013 59

 OMV
Technical Information
Technical Data

Technical data
for OMV, OMVW and OMVS
OMV OMV OMV OMV OMV
Type OMVW OMVW OMVW OMVW OMVW
OMVS OMVS OMVS OMVS OMVS
Motor size 315 400 500 630 800
cm3 400.9 499.6 629.1 801.8
Geometric displacement 314.5 [19.19]
[in3] [24.46] [30.49] [38.39] [48.93]
min-1 cont. 510 500 400 315 250
Max. speed
[rpm] int1) 630 600 480 380 300
920 1180 1460 1660 1880
cont.
Nm [8140] [10440] [12920] [14690] [16640]
Max. torque
[lbf·in] 1110 1410 1760 1940 2110
int.1)
[9820] [12480] [15580] [17170] [18680]
42.5 53.5 53.5 48.0 42.5
cont.
kW [57.0] [71.7] [71.7] [64.4] [57.0]
Max. output
[hp] 51.0 64.0 64.0 56.0 48.0
int.1)
[68.4] [85.8] [85.8] [75.1] [64.4]
200 200 200 180 160
cont.
[2900] [2900] [2900] [2610] [2320]
bar 240 240 240 210 180
Max. pressure drop int.1)
[psi] [3480] [3480] [3480] [3050] [2610]
280 280 280 240 210
peak2)
[4060] [4060] [4060] [3480] [3050]
160 200 200 200 200
cont.
l/min [42.3] [52.8] [52.8] [52.8] [52.8]
Max. oil flow
[USgal/min] 200 240 240 240 240
int.1)
[52.8] [63.4] [63.4] [63.4] [63.4]
Max. starting pressure bar 8 8 8 8 8
with unloaded shaft [psi] [116] [116] [116] [116] [116]
at max. press. drop cont. 710 910 1130 1330 1510
Nm [lbf·in] [6280] [8050] [10000] [11770] [13360]
Min. starting torque
at max. press. drop int.1) 850 1090 1360 1550 1700
Nm [lbf·in] [7520] [9650] [12040] [13720] [15050]

Max. return pressure

Type Max. inlet pressure
with drain line
bar 210 140
cont.
[psi] [3050] [2030]
OMV
bar 250 175
OMVW int.1)
[psi] [3630] [2540]
OMVS
bar 300 210
peak2)
[psi] [4350] [3050]

1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: The permissible values may occur for max. 1% of every minute.
2)

For max. permissible combination of flow and pressure, see function diagram for actual motor.

60 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
Technical Data

Max. Permissible Shaft OMV with check valves OMV with check valves and
Seal Pressure and without use of drain with drain connection:
connection: The shaft seal pressure equals
The pressure on the shaft seal the pressure on the drain line.
never exceeds the pressure in
the return line 151-320.10

Max. return pressure without drain line or max. pressure in the drain line
P P
psi bar
1500
100
90
1200
80
70
900
60
50
600 40
30
300 20
10
0 0
0 100 200 300 400 500 600 max. min-1
(rpm)

151-1673.10

– – – – Intermittent operation: the permissible values may occur for max. 10% of every minute.
Continuous operation

520L0407 • Rev EK • Jun 2013 61

 OMV
Technical Information
Technical Data

Pressure Drop in Motor ∆p ∆p

psi bar
16

200 14

12
150 10

8
100
6

4
50
2

0 0 Q
0 20 40 60 80 100 120 140 160 180 200 l/min

Q
0 5 10 15 20 25 30 35 40 45 50 US gal/min

151-1410.10
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s (165 SUS)

Oil Flow in Drain Line The table shows the max. oil flow in the Pressure Viscosity Oil flow in
drop drain line
drain line at a return pressure less than
bar mm2/s l/min
5-10 bar [75-150 psi]. [psi] [SUS] [US gal/min]
20 3.0
140 [100] [0.79]
[2030] 35 2.0
[165] [0.53]
20 6.0
210 [100] [1.59]
[3050] 35 4.0
[165] [1.06]

Direction of Shaft
Rotation

62 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
Technical Data

Permissible Shaft Loads Mounting flange: Shaft:

for OMV Standard All shaft types
Prad. Prad.
lbf N
16000 70000
0 Pmax. =15000 N
- +
14000 =3372 lbf
60000
12000
50000
10000
40000
8000
30000
6000
20000
4000

2000 10000

0 0
-80 -60 -40 -20 0 20 40 60 80 100 120 mm

-3 -2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 in

151-1973.10

Mounting flange: Shaft:

Wheel All shaft types
Prad. Prad.
lbf N
16000 70000
0 Pmax. =15000 N
- +
14000 =3372 lbf
60000
12000
50000
10000
40000
8000
30000
6000
20000
4000

2000 10000

0 0
0 20 40 60 80 100 120 140 160 180 200 mm

0 1 2 3 4 5 6 7 in

151-1969.10

The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of
the distance from the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at
100 min-1) at rated output torque, when mineral-based hydraulic oil with a sufficient
content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown
in the curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the
chapter "Bearing dimensioning" in the technical information "General Orbital motors"
520L0232.

520L0407 • Rev EK • Jun 2013 63

 OMV
Technical Information
Technical Data

Permissible shaft loads Mounting flange: Shaft:

for OMV SAE-C All shaft types
Prad. Prad.
lbf N
14000
60000
0 Pmax. =10000 N
12000 A B
- +
=2248 lbf
50000
10000 B
40000
8000 A
30000
6000

20000
4000

2000 10000

0 0
-80 -60 -40 -20 0 20 40 60 80 100 120 mm

-3 -2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 in

151-1965.10

A: Cyl. 2.25 in shaft

B: Splined 2.125 in shaft

The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of
the distance from the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at
100 min-1) at rated output torque, when mineral-based hydraulic oil with a sufficient
content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown
in the curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the
chapter "Bearing dimensioning" in the technical information "General Orbital motors"
520L0232.

64 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
Function Diagrams

Function Diagrams OMV 315

Q=10 l/min
[2.6 US gal/min]

25 l/min
[6.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

100 l/min
[26.4 US gal/min]

125 l/min
[33.0 US gal/min]

150 l/min
[39.6 US gal/min]
160 l/min
[42.2 US gal/min]

Q=200 l/min
[52.8 US gal/min]
lbf•in Nm

11000
1200
10000
1100
∆ p=240 bar
9000 1000 3480 psi

8000 N=50kW
900
200 bar
7000 800 2900 psi
170 bar
40kW
700 30kW 2540 psi
6000 30hp 50hp
600 140 bar
5000 20kW
20hp 40hp 2030 psi
500
4000
400
N=5kW 10kW ηt =87% 105 bar
5hp 10hp 1520 psi
3000 85%
300
70 bar
2000 1020 psi
200
80%
1000 100 ηt =70% ∆ p= 35 bar
510 psi
0 0

0 50 100 150 200 250 300 350 400 450 500 550 600 650 min-1
(rpm)

151-870.10

OMV 400
Q=10 l/min
[2.6 US gal/min]
25 l/min
[6.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

100 l/min
[26.4 US gal/min]

125 l/min
[33.0 US gal/min]

150 l/min
[39.6 US gal/min]

175 l/min
[46.2 US gal/min]

200 l/min
[52.8 US gal/min]

Q=240 l/min
[63.4 US gal/min]
lbf•in Nm

14000 1600

1400
12000 ∆ p=240 bar
3480 psi
1200
10000
200 bar
1000 N=50kW 2900 psi
30hp 50hp 175 bar
8000
40hp 40kW 2540 psi
800
20hp 140 bar
6000 30kW 2030 psi
600
ηt =88% 87%
105 bar
10hp 20kW
4000 85% 1520 psi
400
5hp 10kW 70 bar
N=5kW 80% 1020 psi
2000 200
ηt =70% ∆ p= 35 bar
510 psi
0 0

0 50 100 150 200 250 300 350 400 450 500 550 600 min-1
(rpm)

151-871.10

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Intermittent pressure drop and oil flow must not occur simultaneously.

520L0407 • Rev EK • Jun 2013 65

 OMV
Technical Information
Function Diagrams

Function Diagrams
OMV 500
lbf•in Nm

Q=10 l/min
[2.6 US gal/min]
25 l/min
[6.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

100 l/min
[26.4 US gal/min]

125 l/min
[33.0 US gal/min]

150 l/min
[39.6 US gal/min]

175 l/min
[46.2 US gal/min]

200 l/min
[52.8 US gal/min]

Q=240 l/min
[63.4 US gal/min]
16000 1800

1600 ∆ p=240 bar

14000
3480 psi
N=60kW
1400
12000
200 bar
1200 2900 psi
10000 50hp 50kW 175 bar
60hp 2540 psi
1000
8000 40hp 40kW 140 bar
30kW 2030 psi
800
6000 ηt =88% 20kW 105 bar
600 1520 psi
20hp 30hp
4000 N=5kW 87%
400 10kW
85% 70 bar
10hp 1020 psi
2000 200
ηt =70%
80%
5hp ∆ p= 35 bar
510 psi
0 0

0 50 100 150 200 250 300 350 400 450 500 min-1
(rpm)

151-872.10

OMV 630
Q=10 l/min
[2.6 US gal/min]
25 l/min
[6.6 US gal/min]

50 l/min
[13.2 US gal/min]

75 l/min
[19.8 US gal/min]

100 l/min
[26.4 US gal/min]

125 l/min
[33.0 US gal/min]

Q=240 l/min
[63.4 US gal/min]
150 l/min
[39.6 US gal/min]

175 l/min
[46.2 US gal/min]

200 l/min
[52.8 US gal/min]
lbf•in Nm

17500 2000

1750
∆ p=210 bar
15000 N=60kW 3050 psi

1500 50kW 180 bar

30kW 2610 psi
12500 40kW 60hp
1250 50hp 150 bar
10000 2180 psi

1000 40hp
ηt =89% 20kW
30hp
120 bar
1740 psi
7500
750 10kW
87% 90 bar
N=5kW 20hp 1300 psi
5000
500
85% 60 bar
80% 10hp 870 psi
2500 250
ηt =70% 5hp ∆ p= 30 bar
440 psi
0 0

0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 min-1
(rpm)

151-879.10

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Intermittent pressure drop and oil flow must not occur simultaneously.

66 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
Function Diagrams

Function Diagrams
OMV 800
lbf•in Nm

Q = 10 l/min
2.6 US gal/min
25 l/min
6.6 US gal/min

50 l/min
13.2 US gal/min

75 l/min
19.8 US gal/min

100 l/min
26.4 US gal/min

125 l/min
33.0 US gal/min

150 l/min
39.6 US gal/min

175 l/min
46.2 US gal/min

200 l/min
52.8 US gal/min

Q = 240 l/min
63.4 US gal/min
20000 2250

17500 2000 p=180 bar

2610 psi
1750 160 bar
15000
2320 psi
1500
12500 130 bar
1250 1890 psi
10000
1000 100 bar
7500 1450 psi
750
75 bar
5000 1090 psi
500
50 bar
2500 250 730 psi
p=25bar
0 0 360 psi

0 25 50 75 100 125 150 175 200 225 250 275 300 min-1
(rpm)

P301 250

Explanation of function diagram use, basis and conditions can be found on page 5.
 Continuous range
 Intermittent range (max. 10% operation every minute)
Intermittent pressure drop and oil flow must not occur simultaneously.

520L0407 • Rev EK • Jun 2013 67

 OMV
Technical Information
Shaft Version

Shaft Version
82 [3.23]

26 [1.02]

9.5 [0.374]

60˚ R0.5 [0.020] M12 A-A

A: Cylindrical 50 mm shaft A
D: Parallel key

Ø50.018 [1.9692]
Ø50.002 [1.9686]
A14 × 9 × 70
Ø60 [2.36]

53.5 [2.106]
53.2 [2.094]
DIN 6885 A
Keyway deviates from
standard

A
70.5 [2.776] 5.5 [0.217]
4.5 [0.177] 14.000 [0.5512]
70.0 [2.756]
13.957 [0.5495]
79 [3.11] D

82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]

60˚
R0.5 [0.020] 3/8 -16 UNC A-A
A
B: Cylindrical 2.25 in shaft
for OMV with standard
mounting flange
Ø57.15 [2.250]
Ø57.10 [2.248]
Ø60 [2.36]

62.92 [2.477]
62.66 [2.467]
E: Parallel key B
1/2 × 1/2 × 21/4 in
B.S. 46
Keyway deviates from
standard
A
13.1 [0.516]
10.9 [0.429]
12.73 [0.501]
12.70 [0.500]
E
57.5 [2.264]
56.9 [2.240]

99.2 [3.906]
98.8 [3.890]
min. 26 [1.02]

½ -20 UNF
60˚
R0.5 [0.020] A-A
C: Cylindrical 2.25 in shaft A
for OMV with mounting
flange SAE-C
57.15 [2.250]
57.10 [2.248]
Ø60 [2.36]

F: Parallel key
62.93 [2.478]
62.66 [2.467]

1/2 × 1/2 × 21/4 in C

B.S. 46
Keyway deviates from
standard
A
70.4 [2.772]
70.2 [2.763] 12.73 [0.501]
12.70 [0.500] F

151-878.12

68 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
Shaft Version

Shaft Version 82[3.23]

26 [1.02]

45˚ 9.5 [0.374]

R0.5 [0.020] M12
A-A
D: Involute splined shaft A
ANS B92.1 - 1970 standard
Flat root side fit
Pitch 8/16

53.975 [2.1250]
53.950 [2.1240]
Ø60 [2.36]
Teeth 16
Major dia. 2.125 in D
Pressure angle 30°

A
58 [2.28]
56 [2.20]

82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]
45˚
3/8 -16 UNC
R0.5 [0.020] A-A
US Version
A
E: Involute splined shaft
for OMV with standard
mounting flange
Ø53.975 [2.1250]
Ø53.950 [2.1240]

ANS B92.1 - 1970 standard

Ø60 [2.36]

Flat root side fit E

Pitch 8/16
Teeth 16
Major dia. 2.125 in
Pressure angle 30°
A
57 [2.24]
55 [2.17]

76.9 [3.028]
76.5 [3.011]
min. 26 [1.02]

½ -20 UNF
US Version 30˚ R0.5 [0.020]
A-A
F: Involute splined shaft A
for OMV with mounting
flange SAE-C
ANS B92.1 - 1970 standard
Ø53.972 [2.1249]
Ø53.954 [2.1242]
Ø60 [2.36]

Flat root side fit

Pitch 8/16 F
Teeth 16
Major dia. 2.125 in
Pressure angle 30°

A
56.3 [2.217]
55.3 [2.177]

151-1918.10

520L0407 • Rev EK • Jun 2013 69

 OMV
Technical Information
Shaft Version

Shaft Version

23 [0.91]
A-A
7 [0.28]
I J
G: Tapered 60 mm shaft A
(ISO/R775)
J: DIN 937
Across flats: 65 mm

M42x3 [0.12]
Ø60 [2.36]

Tightening torque:

Ø78 [3.07]
Ø8 [0.31]

Ø9 [0.35]
750 ±50 Nm [6640 ±440 lbf·in] G

32.25 [1.270]
32.05 [1.262]
I: Taper 1:10
K: Parallel key
B16 × 10 × 32
DIN 6885
A
Keyway deviates from
40.5 [1.594]
standard 40.0 [1.575]
6 [0.24]
16.000 [0.6299] K
70 [2.76] 15.957 [0.6282]

105 [4.13]

16 [0.63]
45˚
4.5 [0.177]
L M A-A
A
H: Tapered 2.25 in shaft
L: Cone 1:8
SAE J501
Ø57.20 [2.252]
Ø57.10 [2.248]
Ø60 [2.36]

M: 11/2 - 18 UNEF
Ø4 [0.16]

Across flats: 23/8 in H

Tightening torque:
750 ±50 Nm [6640 ±440 lbf·in]
7.29 [0.287]*
7.19 [0.283]

N: Parallel key
9/16 × 9/16 × 2 in A
B.S. 46
Keyway deviates from 51.1 [2.012] 14.308 [0.5633]
50.5 [1.988] 14.288 [0.5625]
standard 73.6 [2.898] N
72.4 [2.850]
100.4 [3.953]
99.6 [3.921]

151-1919.10

70 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
Technical Data

Port Thread Versions A B

Ø45.5 [1.791]
Ø45.0 [1.772]
E F

min. 18 [0.71]

min. 19 [0.75]
A: G main ports B: UN main ports
E: ISO 228/1 - G1 F: 1 5/16 - 12 UN
O-ring boss port

C D
Ø22.5 [0.886]
Ø22.0 [0.866]

G H

min. 13 [0.51]
min. 12 [0.47]

151-1978.10

C: G drain port D: UNF drain port

G: ISO 228/1 - G1/4 H: 9/16 - 18 UNF
O-ring boss port

520L0407 • Rev EK • Jun 2013 71

 OMV
Technical Information
Dimensions – European Version

Dimensions Ø160.000 [6.2992]

Ø159.937 [6.2967]
Standard Flange
Ø146.4 [5.764]
Ø145.0 [5.710]

Ø83 [3.27]
L3

2 [0.08]x45˚
11 [0.43]

39.4 [1.551]
38.6 [1.520]
40 [1.57]

33˚

R1.6 [0.063]
60 [2.36]

20 [0.79]
L2

C 69 [2.72] 8 [0.31]

E
L1
14.0 [0.551]
13.0 [0.512]
L

14.0 [0.551]
13.0 [0.512]

max. 76 [2.99]
14.0 [0.551]
13.0 [0.512]
24.6 [0.969]
23.4 [0.921]

14.0 [0.551]
13.0 [0.512]

23.9 [0.941] 23.9 [0.941]

22.9 [0.902] 22.9 [0.902] max. 77 [3.03] max. 81 [3.19]

23.9 [0.941] 23.9 [0.941]

D 22.9 [0.902] 22.9 [0.902]
25.3 [0.996] 25.3 [0.996]
24.7 [0.972] 24.7 [0.972]
120 [4.72]
max. 149 [5.87]

0]
89
[7. 58]
0 0.4 [7.8
max. 179 [7.05]

Lmax L1* L2 L3 Ø2 99.6

Ø1
Type mm mm mm Output shaft mm
[in] [in] [in] [in]
215 22.0 160 Cyl. 50 mm 82
OMV 315
[8.46] [0.866] [6.30] Splined 2.125 in [3.23]
222 29.0 167 105
OMV 400 Tapered 60 mm
[8.74] [1.142] [6.57] [4.13]
230 37.0 175 C: Drain connection
OMV 500
[9.05] [1.457] [6.89] G 1⁄4; 12 mm [0.47 in] deep
D: M12; 12 mm [0.47 in] deep Ø18 [0.71]
240 47.5 186
OMV 630 R16 [0.63] max. 179 [7.05]
[9.45] [1.870] [7.32] E: G 1; 18 mm [0.71 in] deep
254 61.5 200
OMV 800 *) The gearwheel set is 3.5 mm
[10.00] [2.421] [7.87]
[0.138 in] wider across the
rollers than the L1 dimensions 151-890.11

72 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
Dimensions – US Version

Standard Flange Ø160.000 [6.2992]

Ø159.937 [6.2967]

Ø146.3 [5.760]
Ø145.7 [5.736]
Ø90 [3.54]
Ø88 [3.46]
L3

2 [0.08]x45˚
11 [0.43]

39.4 [1.551]
38.6 [1.520]
40 [1.57]

33˚

R1.6 [0.063]
60 [2.36]

20 [0.79]
77 [3.03]
L2

C 69 [2.72]

D
L1
L

max. 76 [2.99]
24.6 [0.969]
23.4 [0.921]

25.3 [0.996] 25.3 [0.996] max. 77 [3.03] max. 83 [3.27]

24.7 [0.972] 24.7 [0.972]
120 [4.72]
max. 149 [5.87]

Lmax L1* L2 L3 0]
89
[7. 58]
Type mm mm mm Output shaft mm 0.4 [7.8
max. 179 [7.05]

0
Ø2 99.6
[in] [in] [in] [in] Ø1

215 22.0 160 Cyl. 2.25 in 82

OMV 315
[8.46] [0.866] [6.30] Splined 2.125 in [3.23]
222 29.0 167 100
OMV 400 Tapered 2.25 in
[8.74] [1.142] [6.57] [3.94]
230 37.0 175 C: Drain connection
OMV 500
[9.05] [1.457] [6.89] 9⁄16 - 18 UNF;
240 47.5 186 13 mm [0.51 in] deep
OMV 630
[9.45] [1.870] [7.32] O-ring boss port Ø18 [0.71]
254 61.5 200 D: 1 5⁄16 - 12 UN; R16 [0.63] max. 179 [7.05]
OMV 800 19 mm [0.75 in] deep
[10.00] [2.421] [7.87]
O-ring boss port

*) The gearwheel set is 3.5 mm

151-890.11.22
[0.138 in] wider across the
rollers than the L1 dimensions

520L0407 • Rev EK • Jun 2013 73

 OMV
Technical Information
Dimensions – US Version

Ø127.00 [5.000]
SAE-C Flange Ø126.95 [4.998]

L3

16.1 [0.634]
13.7 [0.539]

13.8 [0.543]
13.2 [0.520]
21.0 [0.827]
19.6 [0.772]
85.5 [3.366]

C 71.0 [2.795]
L2

81.5 [3.209]
L
L1
24.0 [0.945]

max. 76 [2.99]
D

25 [0.98] 25 [0.98] max. 77 [3.03] max. 83 [3.27]

max. 121 [4.76]
max. 149 [5.87]
R16 [0.63]

0]
Lmax L1* L2 L3 [6.
39 8]
2 .3 [6.35
Type mm mm mm Output shaft mm 6
Ø1 61.5
max. 147 [5.79]

Ø1
[in] [in] [in] [in]
239 22.0 185 99
OMV 315 Cyl. 2.25 in
[9.41] [0.866] [7.28] [3.90]
246 29.0 192 76.7
OMV 400 Splined 2.125 in
[9.69] [1.142] [7.56] [3.02]
254 37.0 200 C: Drain connection
OMV 500
[10.00] [1.457] [7.87] 9⁄16 - 18 UNF; Ø17.7 [0.697]
265 47.5 211 13 mm [0.51 in] deep Ø17.3 [0.681]
OMV 630 max. 147 [5.79]
[10.43] [1.870] [8.31] O-ring boss port
279 61.5 225 D: 1 5⁄16 - 12 UN;
OMV 800 19 mm [0.75 in] deep
[10.98] [2.421] [8.86]
O-ring boss port
151-1485.10

*) The gearwheel set is 3.5 mm

[0.138 in] wider across the
rollers than the L1 dimensions

74 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
Dimensions – European Version

Ø180.000 [7.0866]
Wheel Ø179.937 [7.0841]
Ø146.4 [5.764]
Ø145.0 [5.710]
Ø148.0 [5.827]
Ø83 [3.27] Ø147.9 [5.823]
2 [0.08]x45˚
L3

33˚

max. 107.7 [4.240]

108 [4.25]
79 [3.11]

10 [0.39]

R1.2 [0.047]
22 [0.87]

8 [0.31]
20 [0.79]

R1.2 [0.047]
L1
3.6[0.142]

14.0 [0.551]
13.0 [0.512]
L2

14.0 [0.551]
13.0 [0.512]

C
L

max. 76 [2.99]
14.0 [0.551]
13.0 [0.512]
24.6 [0.969]
23.4 [0.921]

14.0 [0.551]
13.0 [0.512]

23.9 [0.941] 23.9 [0.941] max. 77 [3.03] max. 81 [3.19]

22.9 [0.902] 22.9 [0.902]
85 [3.35]
23.9 [0.941] 23.9 [0.941]
22.9 [0.902] 22.9 [0.902]
25.3 [0.996] 25.3 [0.996]
D 24.7 [0.972] 24.7 [0.972] E
120 [4.72]
max. 149 [5.87]

Ø194.000 [7.6378]
Ø193.928 [7.6350]

1]
83 7]
[8.
4 .3 [8.80
max. 198 [7.80]

2
Ø2 23.7
Ø2
Lmax L1* L2 L3
Type mm mm mm Output shaft mm
[in] [in] [in] [in]
OMVW 146 22.0 92 82
Cyl. 50 mm
315 [5.75] [0.866] [3.62] [3.23]
OMVW 153 29.0 99 105
Tapered 60 mm
400 [6.02] [1.142] [3.90] [4.13]
OMVW 161 37.0 107 C: Drain connection
500 [6.34] [1.457] [4.21] G 1⁄4; 12 mm [0.47 in] deep Ø18 [0.71]
OMVW 172 47.5 118 D: M12; 12 mm [0.47 in] deep R16 [0.63] max. 198 [7.80]
630 [6.77] [1.870] [4.65] E: G 1; 18 mm [0.71 in] deep
OMVW 185 61.5 132
800 [7.28] [2.421] [5.20] *) The gearwheel set is 3.5 mm
[0.138 in] wider across the
151-899.11
rollers than the L1 dimensions

520L0407 • Rev EK • Jun 2013 75

 OMV
Technical Information
Dimensions – US Version

Wheel Ø180.000 [7.0866]

Ø179.937 [7.0841]
Ø146.3 [5.760]
Ø145.7 [5.736]
Ø90 [3.54] Ø148.0 [5.827]
Ø88 [3.46] Ø147.9 [5.823]
100.4 [3.953]

2 [0.08]x45˚
99.6 [3.921]

33˚

max. 107.7 [4.240]

108 [4.25]
79 [3.11]

10 [0.39]

R1.2 [0.047]
22 [0.87]

8 [0.31]
20 [0.79]

R1.2 [0.047]
L1
3.6 [0.142]
L2

C
L

max. 76 [2.99]
24.6 [0.969]
23.4 [0.921]

max. 77 [3.03] max. 83 [3.27]

25.3 [0.996] 25.3 [0.996]
24.7 [0.972] 24.7 [0.972] 85 [3.35]
120 [4.72]
max. 149 [5.87]
D
Ø194.000 [7.6378]
Ø193.928 [7.6350]

1]
83 7]
[8.
4 .3 [8.80
2
max. 198 [7.80]

Ø2 23.7
Ø2

Lmax L1* L2
Type mm mm mm
[in] [in] [in]
C: Drain connection
OMVW 147 22.0 92
9⁄16 - 18 UNF;
315 [5.79] [0.866] [3.62]
13 mm [0.51 in] deep
OMVW 154 29.0 99 O-ring boss port
400 [6.06] [1.142] [3.90] D: 1 5⁄16 - 12 UN;
OMVW 162 37.0 107 19 mm [0.75 in] deep Ø18 [0.71]
500 [6.38] [1.457] [4.21] O-ring boss port R16 [0.63] max. 198 [7.80]

OMVW 172 47.5 118

630 [6.77] [1.870] [4.65] *) The gearwheel set is 3.5 mm
OMVW 187 61.5 132 [0.138 in] wider across the
800 [7.36] [2.421] [5.20] rollers than the L1 dimensions 151-899.11.22

76 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
Dimensions – European Version

Short 28 [1.10]
Ø140.000 [5.5118]
Ø139.937 [5.5093]

1 [0.04]x45˚
8 [0.31]

R1 [0.04] Ø14 [0.55]

22 [0.87]
35 [1.38]
13.0 [0.512] 20 [0.79]

82 [3.23] 8 [0.31]
L2

L1
14.0 [0.551]

14.0 [0.551]
13.0 [0.512]
L

max. 76 [2.99]
14.0 [0.551]
13.0 [0.512]
24.6 [0.969]
23.4 [0.921]

14.0 [0.551]
13.0 [0.512]
23.9 [0.941] 23.9 [0.941] max. 77 [3.03] max. 81 [3.19]
22.9 [0.902] 22.9 [0.902]
23.9 [0.941] 23.9 [0.941]
22.9 [0.902] 22.9 [0.902]
25.3 [0.996] 25.3 [0.996] 58 [2.28]
D 24.7 [0.972] 24.7 [0.972] E
120 [4.72]
max. 149 [5.87] Ø6 [0.24]
m
ax
.Ø
20
7
[8
.1

Ø180
5]

28 [1.10]
.4
Ø179 [7.102]
.6 [7.0
71]

Lmax L1* L2 C: Drain connection 151-900.10

Type mm mm mm G 1⁄4; 12 mm [0.47 in] deep

[in] [in] [in] D: M12; 12 mm [0.47 in] deep
E: G 1; 18 mm [0.71 in] deep
OMVS 171 22.0 117
315 [6.73] [0.866] [4.61]
OMVS 179 29.0 124 *) The gearwheel set is 3.5 mm
400 [7.05] [1.142] [4.88] [0.138 in] wider across the
OMVS 186 37.0 132 rollers than the L1 dimensions
500 [7.32] [1.457] [5.20]
OMVS 197 47.5 143
630 [7.76] [1.870] [5.63]
OMVS 211 61.5 157
800 [8.31] [2.421] [6.18]

520L0407 • Rev EK • Jun 2013 77

 OMV
Technical Information
OMVS

Installing the OMVS The cardan shaft of the OMVS motor acts as an “output shaft”. Because of the movement
of the shaft, no seal can be fitted at the shaft output.
Internal oil leakage from the motor will therefore flow into the attached component.

During start and operation it is important that the spline connection and the bearings
in the attached component receive oil and are adequately lubricated. To ensure that the
spline connection receives sufficient oil, a conical sealing ring between the shaft of the
attached component and the motor intermediate plate is recommended. This method is
used in the OMV.

The conical sealing ring (code. no. 633B9021) is supplied with the motor.

To ensure that oil runs to the bearings and other parts of the attached component, the
stop plate must have a hole in it (see fig. below).

We recommend an O-ring between motor and attached component. The O-ring

(code no. 151B1041) is supplied with the motor. If motor and attached component have
been separated, remember to refill before starting up. Fill the oil through the drain
connection.

2.35 [0.093]
OMVS 2.25 [0.089]
A C
Dimensions of the
F
Sttached Component
B
min. Ø6 [0.24]

K 0.25 [0.010]
6 [0.24]
K 0.1˚ R
min. Ø60 [2.36]

4 [0.16]
Ø140.063 [5.5143]
Ø140.000 [5.5118]
Ø147.9 [5.823]
Ø147.7 [5.815]

Ø61.2 [2.409]
Ø61.0 [2.402]
Ø102 [4.02]
Ø100 [3.94]

Ø71 [2.80]
Ø69 [2.72]
K
Ø46.2 [1.819]
Ø45.8 [1.803]
Ø56.3 [2.217]
Ø55.5 [2.165]

G E
H max. 2 [0.08] min. 5 [0.2]
8.4 [0.331]
7.6 [0.299] 20.5 [0.807]
9.5 [0.374]
19.5 [0.768]
8.5 [0.335]
32.5 [1.280] 28.7 [1.130]
31.5 [1.240] 26.3 [1.035]
53.3 [1.098]
52.7 [2.075]
76.3 [3.004]
75.7 [2.980]

151-815.10

A: O-ring: 140 × 3 mm E: Internal drain channel

B: External drain channel F: M12; min. 18 mm [0.71 in] deep
C: Drain connection G: Oil circulation hole
G 1⁄4; 12 mm [0.47 in] deep H: Hardened stop plate
D: Conical seal ring

78 520L0407 • Rev EK • Jun 2013

 OMV
Technical Information
OMVS

Internal Spline Data for The attached component must have internal splines corresponding to the external
the Component to be splines on the motor cardan shaft (see drawing below).
Attached
Material:
Case hardening steel with a tensile strength corresponding at least to 20 MoCr4
(900 N/mm2) or SAE 8620.

Hardening specification:
•• On the surface: HV = 750 ± 50
•• 0.7 ± 0.2 mm under the surface: HV = 560

Internal involute spline data

Standard ANS B92.1-1970, class 5 (corrected m · X = 1; m = 2.54)

Flat root side fit mm in

Number of
z 16 16
teeth
Pitch DP 10/20 10/20
Rmin
Pressure angle 30° 30°
Pitch dia. D 40.640 1.6
Major dia. Dri 45.2 +0.4 1.780 +0.016 Lo
0 0
Form dia. So
Dfi 44.6 1.756
(min.)
Minor dia. Di 38.5 +0 0.039 1.516 +0 0.0015 Dri
Space width Di
Lo 5.180 ±0.037
0.204 ±0 .0015
Dfi
(circular) l d
Tooth thickness D
So 2.835 0.1116
(circular)
Fillet radius Rmin. 0.4 0.015
151-816.10
Max.
measurement l 32.47 + 0.15
0
1.278 +0.006
0
between pins*
Pin dia. d 5.6 ±0.001 0.22 ±0.00004
* Finished dimensions (when hardened)

Drain Connection on A drain line ought to be used when pressure in the return line can exceed the
OMVS or Attached permissible pressure on the shaft seal of the attached component.
Component
The drain line can be connected at two different points:
1) at the motor drain connection
2) at the drain connection of the attached component.
If a drain line is fitted to the attached component, it must be possible for oil to flow freely
between motor and attached component.

The drain line must be led to the tank in such a way that there is no risk of the motor and
attached component being drained of oil when at rest.
The maximum pressure in the drain line is limited by the attached component and its
shaft seal.

520L0407 • Rev EK • Jun 2013 79

 OMS, OMT and OMV
Technical Information
Weight of Motors

Weight of Motors Weight Weight Weight

Code no Code no Code no
kg [lb] kg [lb] kg [lb]
151B2050 20.0 44.1 151B2190 31.7 69.9 151B3106 32.6 71.9
151B2051 20.5 45.2 151B2191 33.1 73.0 151B3107 33.5 73.9
151B2052 21.0 46.3 151B2192 34.7 76.5 151B3108 34.9 76.9
151B2053 22.0 48.5 151B3000 20.0 44.1 151B3109 36.5 80.5
151B2054 23.0 50.7 151B3001 20.5 45.2 151B3110 31.8 70.1
151B2055 24.0 52.9 151B3002 21.0 46.3 151B3111 32.6 71.9
151B2056 20.0 44.1 151B3003 22.0 48.5 151B3112 33.5 73.9
151B2057 20.5 45.2 151B3004 23.0 50.7 151B3113 34.9 76.9
151B2058 21.0 46.3 151B3005 24.0 52.9 151B3114 36.5 80.5
151B2059 22.0 48.5 151B3006 20.0 44.1 151B3115 32.4 71.4
151B2060 23.0 50.7 151B3007 20.5 45.2 151B3116 33.2 73.2
151B2061 24.0 52.9 151B3008 21.0 46.3 151B3117 34.1 75.2
151B2062 20.0 44.1 151B3009 22.0 48.5 151B3118 35.5 78.3
151B2063 20.5 45.2 151B3010 23.0 50.7 151B3119 37.1 81.8
151B2064 21.0 46.3 151B3011 24.0 52.9 151B3120 32.4 71.4
151B2065 22.0 48.5 151B3012 20.0 44.1 151B3121 33.2 73.2
151B2066 23.0 50.7 151B3013 20.5 45.2 151B3122 34.1 75.2
151B2067 24.0 52.9 151B3014 21.0 46.3 151B3123 35.5 78.3
151B2080 22.0 48.5 151B3015 22.0 48.5 151B3124 37.1 81.8
151B2081 22.5 49.6 151B3016 23.0 50.7 151B3125 22.7 50.1
151B2082 23.0 50.7 151B3017 24.0 52.9 151B3126 23.5 51.8
151B2083 24.0 52.9 151B3018 20.0 44.1 151B3127 24.4 53.8
151B2084 25.0 55.1 151B3019 20.5 45.2 151B3128 25.6 56.4
151B2085 26.0 57.3 151B3020 21.0 46.3 151B3129 27.7 61.1
151B2150 31.8 70.1 151B3021 22.0 48.5 151B3200 31.0 68.3
151B2151 32.6 71.9 151B3022 23.0 50.7 151B3201 31.5 69.4
151B2152 33.5 73.9 151B3023 24.0 52.9 151B3202 32.0 70.5
151B2153 34.9 76.9 151B3024 22.0 48.5 151B3203 33.0 72.8
151B2154 36.5 80.5 151B3025 22.5 49.6 151B3204 34.0 75.0
151B2155 31.8 70.1 151B3026 23.0 50.7 151B3205 35.0 77.2
151B2156 32.6 71.9 151B3027 24.0 52.9 151B3207 31.0 68.3
151B2157 33.5 73.9 151B3028 25.0 55.1 151B3208 31.5 69.4
151B2158 34.9 76.9 151B3029 26.0 57.3 151B3209 32.0 70.5
151B2159 36.5 80.5 151B3030 22.0 48.5 151B3210 33.0 72.8
151B2160 31.8 70.1 151B3031 22.5 49.6 151B3211 34.0 75.0
151B2161 32.6 71.9 151B3032 23.0 50.7 151B3212 35.0 77.2
151B2162 33.5 73.9 151B3033 24.0 52.9 151B4000 24.5 54.0
151B2163 34.9 76.9 151B3034 25.0 55.1 151B4001 25.0 55.1
151B2164 36.5 80.5 151B3035 26.0 57.3 151B4002 25.5 56.2
151B2170 32.4 71.4 151B3036 15.0 33.1 151B4003 26.5 58.4
151B2171 33.2 73.2 151B3037 15.5 34.2 151B4004 27.5 60.6
151B2172 34.1 75.2 151B3038 16.0 35.3 151B4005 28.5 62.8
151B2173 35.5 78.3 151B3039 17.0 37.5 151B4007 24.5 54.0
151B2174 37.1 81.8 151B3040 18.0 39.7 151B4008 25.0 55.1
151B2183 30.0 66.2 151B3041 19.0 41.9 151B4009 25.5 56.2
151B2184 30.8 67.9 151B3100 31.8 70.1 151B4010 26.5 58.4
151B2185 31.7 69.9 151B3101 32.6 71.9 151B4011 27.5 60.6
151B2186 33.1 73.0 151B3102 33.5 73.9 151B4012 28.5 62.8
151B2187 34.7 76.5 151B3103 34.9 76.9 151B4021 24.5 54.0
151B2188 30.0 66.2 151B3104 36.5 80.5 151B4022 25.0 55.1
151B2189 30.8 67.9 151B3105 31.8 70.1 151B4023 25.5 56.2

80 520L0407 • Rev EK • Jun 2013

 OMS, OMT and OMV
Technical Information
Weight of Motors

Weight of Motors Weight Weight Weight

Code no Code no Code no
kg [lb] kg [lb] kg [lb]
151B4024 26.5 58.4 151F0542 10.2 22.5 151F2247 12.1 26.7
151B4025 27.5 60.6 151F0543 10.4 22.9 151F2248 12.8 28.2
151B4026 28.5 62.8 151F0544 10.7 23.6 151F2261 13.1 28.9
151B4028 24.5 54.0 151F0545 11.1 24.5 151F2262 13.1 28.9
151B4029 25.0 55.1 151F0546 11.5 25.4 151F2263 13.6 30.0
151B4030 25.5 56.2 151F0547 12.0 26.5 151F2264 13.1 28.9
151B4031 26.5 58.4 151F0548 12.7 28.0 151F2265 13.6 30.0
151B4032 27.5 60.6 151F0560 9.8 21.6 151F2300 9.8 21.6
151B4033 28.5 62.8 151F0561 10.0 22.1 151F2301 10.0 22.1
151F0500 9.8 21.6 151F0562 10.3 22.7 151F2302 10.3 22.7
151F0501 10.0 22.1 151F0563 10.7 23.6 151F2303 10.7 23.6
151F0502 10.3 22.7 151F0564 11.1 24.5 151F2304 11.1 24.5
151F0503 10.7 23.6 151F0565 11.6 25.6 151F2305 11.6 25.6
151F0504 11.1 24.5 151F0566 12.3 27.1 151F2306 12.3 27.1
151F0505 11.6 25.6 151F0605 13.1 28.9 151F2307 13.1 28.9
151F0506 12.3 27.1 151F0608 11.1 24.5 151F2308 9.8 21.6
151F0507 9.8 21.6 151F0609 13.6 30.0 151F2309 10.0 22.1
151F0508 10.0 22.1 151F0610 13.6 30.0 151F2310 10.3 22.7
151F0509 10.3 22.7 151F2200 9.8 21.6 151F2311 10.7 23.6
151F0510 10.7 23.6 151F2201 10.0 22.1 151F2312 11.1 24.5
151F0511 11.1 24.5 151F2202 10.3 22.7 151F2313 11.6 25.6
151F0512 11.6 25.6 151F2203 10.7 23.6 151F2314 12.3 27.1
151F0513 12.3 27.1 151F2204 11.1 24.5 151F2315 13.1 28.9
151F0514 9.8 21.6 151F2205 11.6 25.6 151F2316 9.8 21.6
151F0515 10.0 22.1 151F2206 12.3 27.1 151F2317 10.0 22.1
151F0516 10.3 22.7 151F2207 9.8 21.6 151F2318 10.3 22.7
151F0517 10.7 23.6 151F2208 10.0 22.1 151F2319 10.7 23.6
151F0518 11.1 24.5 151F2209 10.3 22.7 151F2320 11.1 24.5
151F0519 11.6 25.6 151F2210 10.7 23.6 151F2321 11.6 25.6
151F0520 12.3 27.1 151F2211 11.1 24.5 151F2322 12.3 27.1
151F0521 10.3 22.7 151F2212 11.6 25.6 151F2323 13.1 28.9
151F0522 10.5 23.1 151F2213 12.3 27.1 151F2324 9.8 21.6
151F0523 10.8 23.8 151F2214 9.8 21.6 151F2325 10.0 22.1
151F0524 11.2 24.7 151F2215 10.0 22.1 151F2326 10.3 22.7
151F0525 11.6 25.6 151F2216 10.3 22.7 151F2327 10.7 23.6
151F0526 12.1 26.7 151F2217 10.7 23.6 151F2328 11.1 24.5
151F0527 12.8 28.2 151F2218 11.1 24.5 151F2329 11.6 25.6
151F0528 10.3 22.7 151F2219 11.6 25.6 151F2330 12.3 27.1
151F0529 10.5 23.1 151F2220 12.3 27.1 151F2331 13.1 28.9
151F0530 10.8 23.8 151F2235 10.3 22.7 151F2332 9.8 21.6
151F0531 11.2 24.7 151F2236 10.5 23.1 151F2333 10.0 22.1
151F0532 11.6 25.6 151F2237 10.8 23.8 151F2334 10.3 22.7
151F0533 12.1 26.7 151F2238 11.2 24.7 151F2335 10.7 23.6
151F0534 12.8 28.2 151F2239 11.6 25.6 151F2336 11.1 24.5
151F0535 7.8 17.2 151F2240 12.1 26.7 151F2337 11.6 25.6
151F0536 8.0 17.6 151F2241 12.8 28.2 151F2338 12.3 27.1
151F0537 8.3 18.3 151F2242 10.3 22.7 151F2339 13.1 28.9
151F0538 8.7 19.2 151F2243 10.5 23.1 151F2345 14.0 30.9
151F0539 9.1 20.1 151F2244 10.8 23.8 151F2346 14.0 30.9
151F0540 9.6 21.2 151F2245 11.2 24.7 151F2347 14.0 30.9
151F0541 10.3 22.7 151F2246 11.6 25.6 151F2348 14.0 30.9

520L0407 • Rev EK • Jun 2013 81

 OMS, OMT and OMV
Technical Information
Weight of Motors

Weight of Motors Weight Weight Weight

Code no Code no Code no
kg [lb] kg [lb] kg [lb]
151F2349 14.0 30.9 151F2363 11.1 24.5 151F2395 9.8 21.6
151F2350 9.8 21.6 151F2364 11.6 25.6 151F2396 10.0 22.1
151F2351 10.0 22.1 151F2365 12.3 27.1 151F2397 10.3 22.7
151F2352 10.3 22.7 151F2366 13.1 28.9 151F2398 10.7 23.6
151F2353 10.7 23.6 151F2367 14.0 30.9 151F2399 11.1 24.5
151F2354 11.1 24.5 151F2368 9.8 21.6 151F2400 11.6 25.6
151F2355 11.6 25.6 151F2369 10.0 22.1 151F2401 12.3 27.1
151F2356 12.3 27.1 151F2370 10.3 22.7 151F2402 13.1 28.9
151F2357 13.1 28.9 151F2371 10.7 23.6 151F2403 14.0 30.9
151F2358 14.0 30.9 151F2372 11.1 24.5 151F2413 9.8 21.6
151F2359 9.8 21.6 151F2373 11.6 25.6 151F2414 10.0 22.1
151F2360 10.0 22.1 151F2374 12.3 27.1 151F2415 10.3 22.7
151F2361 10.3 22.7 151F2375 13.1 28.9 151F2416 10.7 23.6
151F2362 10.7 23.6 151F2376 14.0 30.9 151F2417 11.1 24.5

82 520L0407 • Rev EK • Jun 2013

 OMS, OMT and OMV
Technical Information
Notes

Notes

520L0407 • Rev EK • Jun 2013 83

Products we offer: Sauer-Danfoss is a global manufacturer and supplier of high-
quality hydraulic and electronic components. We specialize in
• Bent Axis Motors providing state-of-the-art technology and solutions that excel in
the harsh operating conditions of the mobile off-highway market.
• Closed Circuit Axial Piston Pumps
Building on our extensive applications expertise, we work closely
and Motors
with our customers to ensure exceptional performance for a broad
• Displays range of off-highway vehicles.
• Electrohydraulic Power Steering
We help OEMs around the world speed up system development,
• Electrohydraulics reduce costs and bring vehicles to market faster.
Sauer-Danfoss – Your Strongest Partner in Mobile Hydraulics.
• Hydraulic Power Steering
• Integrated Systems
• Joysticks and Control Handles
Go to www.sauer-danfoss.com for further product information.
• Microcontrollers and Software
• Open Circuit Axial Piston Pumps
• Orbital Motors Wherever off-highway vehicles are at work, so is Sauer-Danfoss.
• PLUS+1™ GUIDE
We offer expert worldwide support for our customers, ensuring
• Proportional Valves the best possible solutions for outstanding performance. And with
an extensive network of Global Service Partners, we also provide
• Sensors
comprehensive global service for all of our components.
• Steering
• Transit Mixer Drives
Please contact the Sauer-Danfoss representative nearest you.

Members of the Sauer-Danfoss Group: Local address:

Comatrol
www.comatrol.com

Schwarzmüller-Inverter
www.schwarzmueller-inverter.com

Turolla
www.turollaocg.com Sauer-Danfoss (US) Company Sauer-Danfoss ApS
2800 East 13th Street DK-6430 Nordborg, Denmark
Ames, IA 50010, USA Phone: +45 7488 4444
Valmova
Phone: +1 515 239 6000 Fax: +45 7488 4400
www.valmova.com Fax: +1 515 239 6618

Hydro-Gear Sauer-Danfoss GmbH & Co. OHG Sauer-Danfoss-Daikin LTD.

www.hydro-gear.com Postfach 2460, D-24531 Neumünster Shin-Osaka TERASAKI 3rd Bldg. 6F
Krokamp 35, D-24539 Neumünster, Germany 1-5-28 Nishimiyahara, Yodogawa-ku
Phone: +49 4321 871 0 Osaka 532-0004, Japan
Sauer-Danfoss-Daikin Fax: +49 4321 871 122 Phone: +81 6 6395 6066
www.sauer-danfoss-daikin.com Fax: +81 6 6395 8585

520L0407 • Rev EK • Jun 2013 www.sauer-danfoss.com