Transfer files from PC to controller via Kfloppy http://www.robot-forum.com/robotforum/fanuc_robot_forum/transfer_...
Welcome, Guest. Please login
or register.
Did you miss your activation
email?
March 06, 2012, 04:21:53 PM
News: Any Problems or Experience with Industrial Robots ?
Register and place your Question / Answer to worldwide Robotexperts right here !
Robotforum | Support for Robotprogrammer
and Users
Industrial Robot Help and Discussion Center
0 Members and 1 Guest are
Fanuc Robot Forum (Moderators: Sven viewing this topic.
Weyer, Jim Tyrer, Lerak, Napierian)
Transfer files from PC to controller via « previous
Kfloppy next »
Pages: [1]
Topic: Transfer files from PC to controller via Kfloppy (Read 632
Author
times)
Kayani Transfer files from PC to controller via Kfloppy
Newbie « on: January 28, 2011, 03:08:45 AM »
Offline
Hi all,
Posts: 7
I want to transfer files from PC to controller and vice versa. The
controller is RH and I have installed Kfloppy on PC. I have the serial
cable with pin out:
pin 2 <-> pin2, pin 3<-> pin3 and pin 5<-> pin7.
My problem is I don’t know how to work from here. I think I can send
files from PC to controller by “emulating” using Kfloppy and it would send
all files in the directory of kfloppy. But that doesn’t work. Also I can’t
seem to change the directory of kfloppy either.
I am a newbie so if any one could walk me through with this I would
greatly appreciate it.
Thanks,
Kayani
Logged
Napierian Re: Transfer files from PC to controller via Kfloppy
Global « Reply #1 on: January 28, 2011, 02:59:49 PM »
Moderator
Emulating on KFloppy basically just turns your PC into a large floppy
Offline drive. All of the commands you need have to be done from the karel
screen of your robot.
Gender:
1 of 3 3/6/2012 10:21 PM
Transfer files from PC to controller via Kfloppy http://www.robot-forum.com/robotforum/fanuc_robot_forum/transfer_...
Posts: 298 We will start with the kfloppy side. I find it best to go into its dos mode
using the system in the file menu. from here its just "CD directory" to
go up a directory or "CD.." to go back one directory (Old dos commands)
when done type "exit" to return to kfloppy. I know there can be issues
in using kfloppy on usb and anything newer than XP
on the robot side, you will need a CRT and to be in the Karel screen. the
following are commands you can use
copy /o FD:*.* BM: (copy and overwrite from floppy drive {kfloppy} to
bubble {robot internam memory})
copy BM:*.* FD: (copy robot files to floppy)
del file x (delete file named x)
Good luck
Logged
Jeff Kocher
Robotics Technologist
2Ri Robotics
www.2rirobotics.com
FAQ - http://www.2rirobotics.com/Robot-Info/Pages/FAQ.aspx
15 Cope Court
Guelph, ON N1K 0A4
Tel 519-829-2335 Ext 24
Fax 519-829-2346
24 Hour service 519-993-2335
Kayani Re: Transfer files from PC to controller via Kfloppy
Newbie « Reply #2 on: January 28, 2011, 06:03:28 PM »
Offline
Hi Napierian,
Posts: 7
Thank you so much for your reply. I have been able to change the
directory by going in "System" like you mentioned.
The issue now is when I type any command at "copy /o FD:*.* BM:" at
KCL> it tells me "Port is in use". I think the files don't get transferred
because 1) I don't see them in internal memory of controller when i type
"dir" at KCL>. 2) At the PC end the emulator says "No activity" and
indicates 0 bytes of files transferred.
If you have any suggestions as to how I can get the port to work, please
let me know. [I am using the port on Operator panel.]
Many thanks again.
Logged
Napierian Re: Transfer files from PC to controller via Kfloppy
Global « Reply #3 on: February 01, 2011, 07:06:35 PM »
Moderator
the few times I have seen port in use, it is because the system has
Offline crashed while transfering files (doesn't release the port as the operation
never completed)
2 of 3 3/6/2012 10:21 PM
Transfer files from PC to controller via Kfloppy http://www.robot-forum.com/robotforum/fanuc_robot_forum/transfer_...
Gender:
Posts: 298
Start with a fresh boot of both the PC, and robot. Make sure the PC is
emulating, and it should allow you to do a "DIR fd:" to show the contents
of your pc directory.
Logged
Jeff Kocher
Robotics Technologist
2Ri Robotics
www.2rirobotics.com
FAQ - http://www.2rirobotics.com/Robot-Info/Pages/FAQ.aspx
15 Cope Court
Guelph, ON N1K 0A4
Tel 519-829-2335 Ext 24
Fax 519-829-2346
24 Hour service 519-993-2335
Kayani Re: Transfer files from PC to controller via Kfloppy
Newbie « Reply #4 on: February 03, 2011, 05:25:31 PM »
Offline
Thank you so much. You are right, restarting both the PC and the
Posts: 7 controller and trying all over again works.
I have been successful in transferring files from PC to controller and vice
versa.
Logged
Pages: [1]
« previous next »
Jump to: => Fanuc Robot Forum go
Forever Login
Login with username, password and session length
Powered by SMF 1.1.16 | SMF © 2011, Simple
Machines
3 of 3 3/6/2012 10:21 PM
