Scribd
Upload
259 views

2.9.2 Lab - Basic Switch and End Device Configuration

This document describes a lab activity to configure a basic network topology with two switches and two PCs. The objectives are to set up the network topology, configure the PCs with static IP addresses, and configure basic settings on the switches including hostname, passwords, interfaces, and verifying connectivity. Students will cable the devices together, configure the PCs and switches, and use ping to verify connectivity between all devices. Reflection questions ask about interface status and potential issues with ping.

Uploaded by

jhon
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
259 views

2.9.2 Lab - Basic Switch and End Device Configuration

This document describes a lab activity to configure a basic network topology with two switches and two PCs. The objectives are to set up the network topology, configure the PCs with static IP addresses, and configure basic settings on the switches including hostname, passwords, interfaces, and verifying connectivity. Students will cable the devices together, configure the PCs and switches, and use ping to verify connectivity between all devices. Reflection questions ask about interface status and potential issues with ping.

Uploaded by

jhon
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Lab - Basic Switch and End Device Configuration

Topology

Addressing Table
Device Interface IP Address Subnet Mask

S1 VLAN 1 192.168.1.1 255.255.255.0


S2 VLAN 1 192.168.1.2 255.255.255.0
PC-A NIC 192.168.1.10 255.255.255.0
PC-B NIC 192.168.1.11 255.255.255.0

Objectives
 Set Up the Network Topology
 Configure PC Hosts
 Configure and Verify Basic Switch Settings

Background / Scenario
In this lab, you will build a simple network with two hosts and two switches. You will also configure basic
settings including hostname, local passwords, and login banner. Use show commands to display the running
configuration, IOS version, and interface status. Use the copy command to save device configurations.
You will apply IP addressing for this lab to the PCs and switches to enable communication between the
devices. Use the ping utility to verify connectivity.
Note: The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.0(2) (lanbasek9 image). Other
switches and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the
commands available and output produced might vary from what is shown in the labs.
Note: Make sure that the switches have been erased and have no startup configurations. Refer to Appendix A
for the procedure to initialize and reload a switch.

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 3 www.netacad.com
Lab - Basic Switch and End Device Configuration

Required Resources
 2 Switches (Cisco 2960 with Cisco IOS Release 15.0(2) lanbasek9 image or comparable)
 2 PCs (Windows with terminal emulation program, such as Tera Term)
 Console cables to configure the Cisco IOS devices via the console ports
 Ethernet cables as shown in the topology

Instructions
Step 1: Set Up the Network Topology
In this step, you will cable the devices together according to the network topology.
a. Power on the devices.
b. Connect the two switches.
c. Connect the PCs to their respective switches.
d. Visually inspect network connections.

Step 2: Configure PC Hosts


a. Configure static IP address information on the PCs according to the Addressing Table.
b. Verify PC settings and connectivity.

Step 3: Configure and Verify Basic Switch Settings


a. Console into the switch. Enter the global configuration mode.
Open Configuration Window

b. Give the switch a name according to the Addressing Table.


c. Prevent unwanted DNS lookups.
d. Enter local passwords. Use class as the privileged EXEC password and cisco as the password for
console access.
e. Configure and enable the SVI according to the Addressing Table.
f. Enter a login MOTD banner to warn about unauthorized access.
g. Save the configuration.
h. Display the current configuration.
i. Display the IOS version and other useful switch information.
j. Display the status of the connected interfaces on the switch.
Close Configuration Window.

k. Configure switch S2.


l. Record the interface status for the following interfaces.

Interface S1 Status S1 Protocol S2 Status S2 Protocol

F0/1 blank blank blank blank

F0/6 blank blank blank blank

F0/18 blank blank blank blank

VLAN 1 blank blank blank blank

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 3 www.netacad.com
Lab - Basic Switch and End Device Configuration

m. From a PC, ping S1 and S2. The pings should be successful.


n. From a switch, ping PC-A and PC-B. The pings should be successful.

Reflection Question
Why some FastEthernet ports on the switches are up and others are down?

Type your answers here.

What could prevent a ping from being sent between the PCs?
Type your answers here.
End of Document

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 3 www.netacad.com

You might also like