K11 FLEX

FLEXIBLE 2 PART
CEMENTITIOUS
WATERPROOFING SYSTEM

TECHNICAL DATA
Tensile Strength > 1.5N/mm2 ASTM D412-2016a
Elongation at break > 150% ASTM D412-2016a
Adhesion to concrete > 0.3 N/mm2 ASTM D4541:2002
ECO FRIENDLY LOW CARBON
Hardness Shore A > 40 ASTM D2240:2015
CRACK BRIDGING
FOOTPRINT Improves water resistance Passed DIN 1048
of concrete by more than Pt 5:1991
7 times @ 0.2kgf/cm2
Chemical resistance Passed
DESCRIPTION
Davco K11 Flex is a flexible 2-part acrylic-modified NaOCI - 0.5%
cementitious waterproofing system. The 2-components NH4OH - 1.25%
of Davco K11 Flex react chemically after mixing to
form a hard and elastic film which bonds tenaciously HCI - 3.7%
to most concrete or masonry substrate to protect Toxicity Passed SS 375
against possible ingress of water.
Bridge cracks up to 2mm Passed
The application of Davco K11 Flex requires the Chloride Content < 0.01%
surface to be saturated or wetted down prior to its Drying Time (30°C) Touch Dry Approx. 1-3 hours
application. This make Davco K11 Flex a practical
and ideal product for waterproofing in damp Foot Trafficable 4 hours
conditions such as basement, wet areas and external Ponding Test 24 hours after
areas of most sites where the surface has to be application
pre-washed prior to applying any waterproofing
system. In external areas, application of Davco K11 Pot Life (@30°C) Approx. 2 hours
Flex is not affected by change in weather conditions. Specifications are subject to change without notification. Results shown are
typical but reflect test procedures used. Actual field performance will depend
on installation methods and site conditions.
Davco K11 Flex can receive direct plaster or screed
without affecting bond. Marbles and tiles can be ADVANTAGES
fixed directly onto Davco K11 Flex with most types of • 2 components eliminates risk of incorrect mixing
Davco adhesives. ratio.
• Seals lightweight aerated blocks
Davco K11 Flex can accommodate slight movement • Seals precast joints
of structure and can be used as a repair material for • Anti-carbonation protection
bridging cracks in substrate or cracks due to • Non-toxic
shrinkage up to 2mm width. • Foot trafficable when cured
• Will not attack metal
USES • No protection require prior to fixing other types of
Apply on internal and external surface of wall and finishes
slab, swimming pools, kitchens, toilets, balcony,
water tanks. External areas parking deck, planter
boxes, sealing precast joints and intersection of two
concrete elements. Protection to lightweight blocks,
hollow blocks, aerated blocks.
Suitable Substrate
• Concrete • Brickwork • Precast Surface
• Lightweight Blocks • Shotcrete
 K11 FLEX
SURFACE PREPARATION APPLICATION (CON’T)
Clean the substrate of any protrusion or Davco K11 Flex must be protected by rendering or
substances that may damage the membrane. screeding after application.
Ensure all surfaces are free from dirt, dust,
Note : If applied directly onto lightweight aerated block, the block must be
grease, oil, wax, curing compounds and any primed with Davco Acrylic Primer until a coloured tint is visible.
other loose contaminating materials.
COVERAGE
Fill all voids, cracks, edges and angles with Set Size (kg) Coverage (m²) Thickness (mm)
Lanko Grout 180 ECO or suitable repair
material, so that the prepared surface is sound, 42kg set 15 – 20 m² Approx. 1.2mm to 1.5mm
even and clean. 36kg set 12 – 17 m² Approx. 1.2mm to 1.5mm
12kg set 4 – 6 m² Approx. 1.2mm to 1.5mm
MIXING 10kg set 3 – 5 m² Approx. 1.2mm to 1.5mm
Put Davco K11 Flex Liquid into a clean mixing
container. Add the Davco K11 Flex Powder Wet film thickness: 0.7 ± 0.1 mm/coat.
gradually while mixing until a lump free plastic
consistency is achieved. NO ADDITION OF PACKAGING
WATER IS ALLOWED. It is recommended that 42 kg set, 36 kg set, 12 kg set & 10 kg set.
mechanical mixing (400-500 rpm) should be
used for 2-3 minutes to ensure proper SHELF LIFE
dispersion of the components. Davco K11 Flex has a shelf life of up to 12 months in
unopened bags and containers when stored in a cool
APPLICATION dry and elevated position.
Pre-wet the surface with clean water. Do not
allow water ponding. Very porous surface must CLEANING
be primed with Davco Acrylic Primer prior to All tools and equipment should be cleaned
applying Davco K11 Flex. Apply the mixed immediately with clean water after use. Hardened
material onto the prepared surface using a material can only be removed mechanically.
block brush, squeegee or roller in a stiffling
action. Apply 1-2 coats finish depending on site HEALTH & SAFETY
conditions and film thickness required. If a Product contains cement, which may cause
trowel is used for application, all undulating or dermatitis. Wear rubber gloves when handling the
uneven areas must be patched to level before product. In case of insufficient ventilation, put on
applying the Davco K11 Flex to prevent the suitable respiratory equipment. Do not apply the
material from building up too thick in one product when the surface temperature is below 5ºC
application. or greater than 45ºC. Product is classified as
non-hazardous. Refer to safety data sheet.
Before a 2nd coat is applied, the 1st coat must be
left for approximately 2-3 hours depending on Disclaimer
the thickness, substrate porosity and the The use of this product is beyond the manufacturer's control and
liability is restricted to the replacement of material proven faulty.
temperature until it is dry. The manufacturer is not responsible for any loss or damage arising
from incorrect usage. Specifications are subjected to changes
without prior notice. Before application, customers and users are
requested to check that they have the latest version of this
document from our website www.parexgroup.com.sg

PAREXGROUP PTE LTD

28 TUAS SOUTH AVENUE 8, SINGAPORE 637648
TEL: (65) 6861 0632 FAX: (65) 6862 3915
EMAIL: SALES@ PAREXGROUP.COM.SG
ISO 14064 : 2006
WEBSITE: WWW.PAREXGROUP.COM.SG Certificate GMS-C / GHG / 0002
ONLINE STORE: DAVCO-ONLINE .COM.SG

ParexGroup, a French multi-national company with

headquarters in Paris, is a leading manufacturer of speciality
products for the construction industry with
operations in more than 20 countries, and our 2700 people
around the world are the cornerstone of our growing
organization.

Updated WP04 May 2018