GA-990FXA-UD3

User's Manual
Rev. 3001
12ME-990FXA3-3001R
Motherboard
GA-990FXA-UD3
Motherboard
GA-990FXA-UD3
Sept. 21, 2012
Sept. 21, 2012
Copyright
© 2012 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE
without prior notice.

No part of this manual may be reproduced, copied, translated, transmitted, or published in

any form or by any means without GIGABYTE's prior written permission.

Documentation Classifications
In order to assist in the use of this product, GIGABYTE provides the following types of docu-
mentations:
„„ For quick set-up of the product, read the Quick Installation Guide included with the product.
„„ For detailed product information, carefully read the User's Manual.

For product-related information, check on our website at: http://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV:
1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before
updating motherboard BIOS, drivers, or when looking for technical information.

Example:
 Table of Contents
Box Contents....................................................................................................................6
Optional Items..................................................................................................................6
GA-990FXA-UD3 Motherboard Layout...........................................................................7
GA-990FXA-UD3 Motherboard Block Diagram...............................................................8
Chapter 1 Hardware Installation......................................................................................9
1-1 Installation Precautions.................................................................................... 9
1-2 Product Specifications.................................................................................... 10
1-3 Installing the CPU and CPU Cooler............................................................... 13
1-3-1 Installing the CPU...................................................................................................13
1-3-2 Installing the CPU Cooler.......................................................................................15
1-4 Installing the Memory..................................................................................... 16
1-4-1 Dual Channel Memory Configuration.....................................................................16
1-4-2 Installing a Memory.................................................................................................17
1-5 Installing an Expansion Card.......................................................................... 18
1-6 Setting up AMD CrossFire™/NVIDIA SLI Configuration................................ 19
1-7 Back Panel Connectors.................................................................................. 20
1-8 Internal Connectors........................................................................................ 22
Chapter 2 BIOS Setup...................................................................................................31
2-1 Startup Screen................................................................................................ 32
2-2 The Main Menu............................................................................................... 33
2-3 M.I.T................................................................................................................ 35
2-4 System............................................................................................................ 43
2-5 BIOS Features................................................................................................ 44
2-6 Peripherals...................................................................................................... 47
2-7 Power Management........................................................................................ 51
2-8 Save & Exit..................................................................................................... 53

-4-
Chapter 3 Drivers Installation........................................................................................55
3-1 Installing Chipset Drivers................................................................................ 55
3-2 Application Software....................................................................................... 56
3-3 Technical Manuals.......................................................................................... 56
3-4 Contact........................................................................................................... 57
3-5 System............................................................................................................ 57
3-6 Download Center............................................................................................ 58
3-7 New Program.................................................................................................. 58
Chapter 4 Unique Features............................................................................................59
4-1 BIOS Update Utilities...................................................................................... 59
4-1-1 Updating the BIOS with the Q-Flash Utility............................................................59
4-1-2 Updating the BIOS with the @BIOS Utility.............................................................62
4-2 EasyTune 6..................................................................................................... 63
4-3 Q-Share.......................................................................................................... 64
4-4 Smart Recovery 2........................................................................................... 65
4-5 Auto Green...................................................................................................... 67
Chapter 5 Appendix.......................................................................................................69
5-1 Configuring SATA Hard Drive(s) .................................................................... 69
5-1-1 Configuring AMD SB950 SATA Controllers ......................................................... 69
5-1-2 Configuring Marvell 88SE9172 SATA Controller....................................................75
5-1-3 Installing the SATA RAID/AHCI Driver and Operating System..............................81
5-2 Configuring Audio Input and Output............................................................... 89
5-2-1 Configuring 2/4/5.1/7.1-Channel Audio.................................................................. 89
5-2-2 Configuring S/PDIF Out..........................................................................................91
5-2-3 Enabling the Dolby Home Theater Function..........................................................92
5-2-4 Configuring Microphone Recording........................................................................93
5-2-5 Using the Sound Recorder.................................................................................... 95
5-3 Troubleshooting.............................................................................................. 96
5-3-1 Frequently Asked Questions ................................................................................ 96
5-3-2 Troubleshooting Procedure....................................................................................97
5-3-3 Regulatory Statements.......................................................................................... 99

-5-
 Box Contents
55 GA-990FXA-UD3 motherboard
55 Motherboard driver disk
55 User's Manual
55 Quick Installation Guide
55 Four SATA cables
55 I/O Shield

The box contents above are for reference only and the actual items shall depend on the product package you
obtain. The box contents are subject to change without notice.

Optional Items
†† 2-port USB 2.0 bracket (Part No. 12CR1-1UB030-6*R)
†† eSATA bracket (Part No. 12CF1-3SATPW-4*R)
†† 3.5" Front Panel with 2 USB 3.0/2.0 ports (Part No. 12CR1-FPX582-0*R)
†† COM port cable (Part No. 12CF1-1CM001-3*R)
†† 2-port IEEE 1394a bracket (Part No. 12CF1-1IE008-0*R)

-6-
GA-990FXA-UD3 Motherboard Layout

KB_MS_USB ATX_12V
CPU_FAN

OPTICAL

USB_1394_ESATA
Socket AM3+
Marvell
88SE9172
USB_ESATA
PWR_FAN

ATX
R_USB30

USB_LAN

Etron
AUDIO EJ168

PCIEX1_1 AMD 990FX

BAT

Realtek
DDR3_4

DDR3_2

DDR3_3

DDR3_1
GbE LAN PCIEX16_1

PCIEX1_2
GA-990FXA-UD3

AMD SB950 SATA3

PCIEX4_1 4 5
CODEC
2 3
0 1
PCIEX16_2
B_BIOS

PCI
M_BIOS
VIA SYS_FAN1
VT6308 Etron iTE
PCIEX4_2 EJ168 Super I/O

CLR_CMOS
F_AUDIO F_1394 SYS_FAN2 COMA F_USB3 F_USB2 F_USB1 F_USB30 TPM F_PANEL

SPDIF_O

-7-
 GA-990FXA-UD3 Motherboard Block Diagram
2 PCI Express x16 2 PCI Express x4
CPU CLK+/- (200 MHz)

AM3+/AM3 CPU DDR3 2000(O.C.)/1866/1600/1333/1066 MHz

Dual Channel Memory

PCIe CLK
(100 MHz) Hyper Transport 3.0

PCI Express Bus x16 x4

PCI Express Bus

AMD 990FX
x1 x1

Marvell Etron
PCIe CLK 88SE9172 EJ168
(100 MHz)

2 SATA 6Gb/s 2 USB 3.0/2.0

PCI Express Bus 14 USB 2.0/1.1

PCIe CLK x1 x1 x1
(100 MHz)
Etron Dual BIOS
Realtek
GbE LAN EJ168
AMD SB950
6 SATA 6Gb/s
RJ45
2 PCI Express x1 2 USB 3.0/2.0
PCI Bus LAN LPC
Bus COM
VIA iTE
VT6308 Super
CODEC I/O PS/2 KB/Mouse

2 IEEE 1394a
Rear Speaker Out
Center/Subwoofer Speaker Out
Side Speaker Out
MIC
Line Out
Line In

S/PDIF Out

1 PCI

PCI CLK
(33 MHz)
For detailed product information/limitation(s), refer to "1-2 Product Specifications."

-8-
Chapter 1 Hardware Installation
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become
damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's
manual and follow these procedures:
•• Prior to installation, make sure the chassis is suitable for the motherboard.
•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
•• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
•• When connecting hardware components to the internal connectors on the motherboard, make
sure they are connected tightly and securely.
•• When handling the motherboard, avoid touching any metal leads or connectors.
•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic com-
ponents such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep
your hands dry and first touch a metal object to eliminate static electricity.
•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
•• Before unplugging the power supply cable from the motherboard, make sure the power supply
has been turned off.
•• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
•• Before using the product, please verify that all cables and power connectors of your hardware
components are connected.
•• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
•• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
•• Do not place the computer system on an uneven surface.
•• Do not place the computer system in a high-temperature environment.
•• Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
•• If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.

-9- Hardware Installation

1-2 Product Specifications
CPU Š AM3+ Socket:
- AMD AM3+ FX processors
- AMD AM3 Phenom™ II processor/ AMD Athlon™ II processor
(Go to GIGABYTE's website for the latest CPU support list.)
Hyper Transport
Š 5200 MT/s
Bus
Š North Bridge: AMD 990FX
Chipset
Š South Bridge: AMD SB950
Memory Š 4 x 1.5V DDR3 DIMM sockets supporting up to 32 GB of system memory
* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical
memory is installed, the actual memory size displayed will be less than the size of
the physical memory installed.
Š Dual channel memory architecture
Š Support for DDR3 2000 (O.C.)/1866/1600/1333/1066 MHz memory modules
* To support a DDR3 1866 MHz (and above) memory, you must install an AM3+ CPU
first.
Š Support for Extreme Memory Profile (XMP) memory modules
(Go to GIGABYTE's website for the latest supported memory speeds and memory
modules.)
Audio Š Realtek ALC889 codec
Š High Definition Audio
Š 2/4/5.1/7.1-channel
Š Support for Dolby® Home Theater
Š Support for S/PDIF Out
LAN Š 1 x Realtek GbE LAN chip (10/100/1000 Mbit)
Expansion Slots Š 2 x PCI Express x16 slots, running at x16 (PCIEX16_1/PCIEX16_2)
* For optimum performance, if only one PCI Express graphics card is to be installed,
be sure to install it in the PCIEX16_1 slot; if you are installing two PCI Express
graphics cards, it is recommended that you install them in the PCIEX16_1 and
PCIEX16_2 slots.
Š 2 x PCI Express x16 slots, running at x4 (PCIEX4_1/PCIEX4_2)
Š 2 x PCI Express x1 slots
(All PCI Express slots conform to PCI Express 2.0 standard.)
Š 1 x PCI slot
Multi-Graphics Š Support for 2-Way AMD CrossFire™/NVIDIA SLI technology (PCIEX16_1 and
Technology PCIEX16_2)
Storage Interface Š South Bridge:
- 6 x SATA 6Gb/s connectors (SATA3 0~5) supporting up to 6 SATA 6Gb/s
devices
- Support for RAID 0, RAID 1, RAID 5, RAID 10, and JBOD
ŠŠ Marvell 88SE9172 chip:
- 2 x eSATA 6Gb/s connectors on the back panel supporting up to 2 SATA
6Gb/s devices
* Actual transfer rate is dependent on the device being connected.
- Support for RAID 0, RAID 1, and JBOD
Hardware Installation - 10 -
USB Š Chipset:
- Up to 14 USB 2.0/1.1 ports (8 ports on the back panel, 6 ports available
through the internal USB headers)
Š 2 x Etron EJ168 chips:
- Up to 4 USB 3.0/2.0 ports (2 ports on the back panel, 2 ports available through
the internal USB header)

* Be sure to connect your USB device(s) to the USB 2.0/1.1 ports before the USB 3.0
driver is installed. (refer to the labels in section 1-7, "Back Panel Connectors.")
IEEE 1394 ŠŠ VIA VT6308 chip:
- Up to 2 IEEE 1394a ports (1 port on the back panel, 1 port available through
the internal IEEE 1394a header)
Internal Š 1 x 24-pin ATX main power connector
Connectors Š 1 x 8-pin ATX 12V power connector
Š 6 x SATA 6Gb/s connectors
Š 1 x CPU fan header
Š 2 x system fan headers
Š 1 x power fan header
Š 1 x front panel header
Š 1 x front panel audio header
Š 1 x S/PDIF Out header
Š 3 x USB 2.0/1.1 headers
Š 1 x USB 3.0/2.0 header
Š 1 x IEEE 1394a port
Š 1 x serial port header
Š 1 x Clear CMOS jumper
Š 1 x Trusted Platform Module (TPM) header
Back Panel Š 1 x PS/2 keyboard/mouse port
Connectors Š 1 x optical S/PDIF Out connector
Š 1 x IEEE 1394a port
Š 2 x eSATA 6Gb/s connectors
Š 8 x USB 2.0/1.1 ports
Š 2 x USB 3.0/2.0 ports
Š 1 x RJ-45 port
Š 6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker
Out/Side Speaker Out/Line In/Line Out/Microphone)
I/O Controller Š iTE I/O Controller Chip

- 11 - Hardware Installation
 Hardware Š System voltage detection
Monitor Š CPU/System temperature detection
Š CPU/System/Power fan speed detection
Š CPU overheating warning
Š CPU/System/Power fan fail warning
Š CPU/System fan speed control
* Whether the CPU/system fan speed control function is supported will depend on the
CPU/system cooler you install.
BIOS Š 2 x 32 Mbit flash
Š Use of licensed AMI EFI BIOS
Š Support for DualBIOS™
Š PnP 1.0a, DMI 2.0, SM BIOS 2.6, ACPI 2.0a
Unique Features Š Support for @BIOS
Š Support for Q-Flash
Š Support for Xpress Install
Š Support for EasyTune
* Available functions in EasyTune may differ by motherboard model.
Š Support for Smart Recovery 2
Š Support for Auto Green
Š Support for ON/OFF Charge
Š Support for 3TB+ Unlock
Š Support for Q-Share
Bundled
Š Norton Internet Security (OEM version)
Software
Operating
Š Support for Microsoft® Windows 8/7/Vista/XP
System
Form Factor Š ATX Form Factor; 30.5cm x 24.4cm

* GIGABYTE reserves the right to make any changes to the product specifications and product-related information without
prior notice.
* Please visit the Support & Downloads\Utility page on GIGABYTE's website to check the supported operating system(s)
for the software listed in the "Unique Features" and "Bundled Software" columns.

Hardware Installation - 12 -
1-3 Installing the CPU and CPU Cooler
Read the following guidelines before you begin to install the CPU:
• Make sure that the motherboard supports the CPU.
(Go to GIGABYTE's website for the latest CPU support list.)
• Always turn off the computer and unplug the power cord from the power outlet before installing the
CPU to prevent hardware damage.
• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
• Apply an even and thin layer of thermal grease on the surface of the CPU.
• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
of the CPU may occur.
• Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
that the system bus frequency be set beyond hardware specifications since it does not meet the
standard requirements for the peripherals. If you wish to set the frequency beyond the standard
specifications, please do so according to your hardware specifications including the CPU, graphics
card, memory, hard drive, etc.
1-3-1 Installing the CPU
A. Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU.

A Small Triangle Mark-

ing Denotes Pin One AM3+ Socket
of the Socket

A Small Triangle
Marking Denotes AM3+/AM3 CPU
CPU Pin One

- 13 - Hardware Installation
B. Follow the steps below to correctly install the CPU into the motherboard CPU socket.

• Before installing the CPU, make sure to turn off the computer and unplug the power cord from the
power outlet to prevent damage to the CPU.
• Do not force the CPU into the CPU socket. The CPU cannot fit in if oriented incorrectly. Adjust the
CPU orientation if this occurs.
Step 1:
CPU Socket Completely lift up the CPU socket locking lever.
Locking Lever

Step 2:
Align the CPU pin one (small triangle marking) with the triangle mark
on the CPU socket and gently insert the CPU into the socket. Make
sure that the CPU pins fit perfectly into their holes.
Once the CPU is positioned into its socket, place one finger down on
the middle of the CPU, lowering the locking lever and latching it into
the fully locked position.

Hardware Installation - 14 -
1-3-2 Installing the CPU Cooler
Follow the steps below to correctly install the CPU cooler on the motherboard. (The following procedure uses
the GIGABYTE cooler as the example.)

Step 1: Step 2:
Apply an even and thin layer of thermal grease on Place the CPU cooler on the CPU.
the surface of the installed CPU.

Step 3: Step 4:
Hook the CPU cooler clip to the mounting lug on Turn the cam handle from the left side to the
one side of the retention frame. On the other side, right side (as the picture above shows) to lock
push straight down on the CPU cooler clip to hook into place. (Refer to your CPU cooler installation
it to the mounting lug on the retention frame. manual for instructions on installing the cooler.)

Step 5:
Finally, attach the power connector of the CPU cooler to the CPU fan
header (CPU_FAN) on the motherboard.

Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU
cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU.

- 15 - Hardware Installation
1-4 Installing the Memory
Read the following guidelines before you begin to install the memory:
• Make sure that the motherboard supports the memory. It is recommended that memory of the same
capacity, brand, speed, and chips be used.
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
• Always turn off the computer and unplug the power cord from the power outlet before installing the
memory to prevent hardware damage.
• Memory modules have a foolproof design. A memory module can be installed in only one direction.
If you are unable to insert the memory, switch the direction.
1-4-1 Dual Channel Memory Configuration
This motherboard provides four DDR3 memory sockets and supports Dual Channel Technology. After the
memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling
Dual Channel memory mode will double the original memory bandwidth.
The four DDR3 memory sockets are divided into two channels and each channel has two memory sockets as
following:
Channel A: DDR3_2, DDR3_4
Channel B: DDR3_1, DDR3_3

Dual Channel Memory Configurations Table

DDR3_4 DDR3_2 DDR3_3 DDR3_1
Two Modules -- DS/SS -- DS/SS
DS/SS -- DS/SS --
Four Modules DS/SS DS/SS DS/SS DS/SS
(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)
DDR3_4
DDR3_2
DDR3_3
DDR3_1

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1. Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.
2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory
of the same capacity, brand, speed, and chips be used for optimum performance. For optimum per-
formance, when enabling Dual Channel mode with two memory modules, we recommend that you
install them in the DDR3_1 and DDR3_2 sockets.

Hardware Installation - 16 -
1-4-2 Installing a Memory
Before installing a memory module, make sure to turn off the computer and unplug the power
cord from the power outlet to prevent damage to the memory module. DDR3 and DDR2 DIMMs are
not compatible to each other or DDR DIMMs. Be sure to install DDR3 DIMMs on this motherboard.

Notch

DDR3 DIMM

A DDR3 memory module has a notch, so it can only fit in one direction. Follow the steps below to correctly install
your memory modules in the memory sockets.
Step 1:
Note the orientation of the memory module. Spread the retaining clips
at both ends of the memory socket. Place the memory module on the
socket. As indicated in the picture on the left, place your fingers on
the top edge of the memory, push down on the memory and insert it
vertically into the memory socket.

Step 2:
The clips at both ends of the socket will snap into place when the
memory module is securely inserted.

- 17 - Hardware Installation
1-5 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card:
• Make sure the motherboard supports the expansion card. Carefully read the manual that came
with your expansion card.
• Always turn off the computer and unplug the power cord from the power outlet before installing an
expansion card to prevent hardware damage.

PCI Express x1 Slot

PCI Express x16 Slot

PCI Slot

Follow the steps below to correctly install your expansion card in the expansion slot.
1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.
2. Align the card with the slot, and press down on the card until it is fully seated in the slot.
3. Make sure the metal contacts on the card are completely inserted into the slot.
4. Secure the card's metal bracket to the chassis back panel with a screw.
5. After installing all expansion cards, replace the chassis cover(s).
6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your
expansion card(s).
7. Install the driver provided with the expansion card in your operating system.

Example: Installing and Removing a PCI Express Graphics Card:

•• Installing a Graphics Card:
Gently push down on the top edge of the card until
it is fully inserted into the PCI Express slot. Make
sure the card is securely seated in the slot and
does not rock.

•• Removing the Card:

Gently push back on the lever on the slot and then lift the card straight out from
the slot.

Hardware Installation - 18 -
1-6 Setting up AMD CrossFire™/NVIDIA SLI Configuration
A. System Requirements
-- Windows 7, Windows Vista or Windows XP operating system
-- A CrossFire/SLI-supported motherboard with two PCI Express x16 slots and correct driver
-- Two CrossFire/SLI-ready graphics cards of identical brand and chip and correct driver
-- CrossFire (Note)/SLI bridge connector
-- A power supply with sufficient power is recommended (Refer to the manual of your graphics cards for the
power requirement)

B. Connecting the Graphics Cards

Step 1:
Observe the steps in "1-5 Installing an Expansion Card" and install CrossFire/SLI graphics cards on the
PCIEX16_1 and PCIEX16_2 slots.

Step 2:
Insert the CrossFire /SLI bridge connector in the CrossFire/SLI gold edge connectors on top of the cards.
(Note)

Step 3:
Plug the display cable into the graphics card on the PCIEX16_1 slot.

C. Configuring the Graphics Card Driver

C-1. To Enable CrossFire Function
After installing the graphics card driver in the operating system, go to
the AMD VISION Engine Control Center. Browse to Performance\
AMD CrossFireX™ and ensure the Enable CrossFireX™ check box is
selected. And click Apply.

C-2. To Enable SLI Function

After installing the graphics card driver in the operating system, go to
the NVIDIA Control Panel. Browse to the Set SLI and Physx Con-
figuration screen and ensure Maximize 3D performance is enabled.

(Note) The bridge connector(s) may be needed or not depending on your graphics cards.
Procedure and driver screen for enabling CrossFire/SLI technology may differ by graphics cards. Refer
to the manual that came with your graphics cards for more information about enabling CrossFire/SLI
technology.
- 19 - Hardware Installation
1-7 Back Panel Connectors

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB
keyboard/mouse, USB printer, USB flash drive and etc.
PS/2 Keyboard/Mouse Port
Use this port to connect a PS/2 mouse or keyboard.
Optical S/PDIF Out Connector
This connector provides digital audio out to an external audio system that supports digital optical audio.
Before using this feature, ensure that your audio system provides an optical digital audio in connector.
IEEE 1394a Port
 he IEEE 1394 port supports the IEEE 1394a specification, featuring high speed, high bandwidth and
T
hotplug capabilities. Use this port for an IEEE 1394a device.
eSATA 6Gb/s Connector
The eSATA 6Gb/s port conforms to SATA 6Gb/s standard and is compatible with SATA 3Gb/s and SATA
1.5Gb/s standards. Use the port to connect an external SATA device or a SATA port multiplier. The Mar-
vell 88SE9172 chip supports RAID function. Refer to Chapter 5, "Configuring SATA Hard Drive(s)," for
instructions on configuring a RAID array.
USB 3.0/2.0 Port
The USB 3.0 port supports the USB 3.0 specification and is compatible to the USB 2.0/1.1 specification.
Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.
Connection/
Speed LED Activity LED Connection/Speed LED: Activity LED:
State Description State Description
Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring
Green 100 Mbps data rate Off No data transmission or receiving is occurring
LAN Port Off 10 Mbps data rate

Hardware Installation - 20 -
Center/Subwoofer Speaker Out Jack (Orange)
Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio configuration.
Rear Speaker Out Jack (Black)
Use this audio jack to connect rear speakers in a 7.1-channel audio configuration.
Side Speaker Out Jack (Gray)
Use this audio jack to connect side speakers in a 4/5.1/7.1-channel audio configuration.
Line In Jack (Blue)
The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out Jack (Green)
The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used
to connect front speakers in a 4/5.1/7.1-channel audio configuration.
Mic In Jack (Pink)
The default Mic in jack. Microphones must be connected to this jack.

In addition to the default speakers settings, the ~ audio jacks can be reconfigured to perform
different functions via the audio software. Only microphones still MUST be connected to the default
Mic in jack ( ). Refer to the instructions on setting up a 2/4/5.1/7.1-channel audio configuration in
Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."

• When removing the cable connected to a back panel connector, first remove the cable from your
device and then remove it from the motherboard.
• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent
an electrical short inside the cable connector.

- 21 - Hardware Installation
1-8 Internal Connectors

1 3

15

4
16
8

9 12 4 13 10 11 14 7

1) ATX_12V 9) SPDIF_O
2) ATX 10) F_USB1/F_USB2/F_USB3
3) CPU_FAN 11) F_USB30
4) SYS_FAN1/SYS_FAN2 12) F_1394
5) PWR_FAN 13) COMA
6) SATA3 0/1/2/3/4/5 14) TPM
7) F_PANEL 15) BAT
8) F_AUDIO 16) CLR_CMOS

Read the following guidelines before connecting external devices:

• First make sure your devices are compliant with the connectors you wish to connect.
• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
• After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.

Hardware Installation - 22 -
1/2) ATX_12V/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components
on the motherboard. Before connecting the power connector, first make sure the power supply is turned
off and all devices are properly installed. The power connector possesses a foolproof design. Connect the
power supply cable to the power connector in the correct orientation.
The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,
the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high
power consumption be used (500W or greater). If a power supply is used that does not provide the
required power, the result can lead to an unstable or unbootable system.
ATX_12V:
8 4
Pin No. Definition
1 GND (Only for 2x4-pin 12V)
2 GND (Only for 2x4-pin 12V)
5 1
3 GND
ATX_12V 4 GND
5 +12V (Only for 2x4-pin 12V)
6 +12V (Only for 2x4-pin 12V)
7 +12V
8 +12V

ATX:
Pin No. Definition Pin No. Definition
12 24 1 3.3V 13 3.3V
2 3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON (soft On/Off)
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 Power Good 20 -5V
9 5VSB (stand by +5V) 21 +5V
10 +12V 22 +5V
11 +12V (Only for 2x12-pin 23 +5V (Only for 2x12-pin ATX)
ATX)
1 13 12 3.3V (Only for 2x12-pin 24 GND (Only for 2x12-pin ATX)
ATX)
ATX

- 23 - Hardware Installation
 3/4/5) CPU_FAN/SYS_FAN1/SYS_FAN2/PWR_FAN (Fan Headers)
The motherboard has a 4-pin CPU fan header (CPU_FAN), a 4-pin (SYS_FAN1) and a 3-pin (SYS_FAN2)
system fan headers, and a 3-pin power fan header (PWR_FAN). Most fan headers possess a foolproof
insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black
connector wire is the ground wire). The motherboard supports CPU fan speed control, which requires the
use of a CPU fan with fan speed control design. For optimum heat dissipation, it is recommended that a
system fan be installed inside the chassis. CPU_FAN:
Pin No. Definition
1 GND
1
2 +12V /Speed Control
CPU_FAN 3 Sense
4 Speed Control
SYS_FAN1:
Pin No. Definition
1 GND
1 2 +12V /Speed Control
SYS_FAN1 3 Sense
4 Reserve
SYS_FAN2/PWR_FAN:
Pin No. Definition
1
1 1 GND
SYS_FAN2 PWR_FAN 2 +12V
3 Sense
• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheat-
ing. Overheating may result in damage to the CPU or the system may hang.
• These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.
6) SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors, Controlled by AMD SB950 South Bridge)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standard. Each SATA connector supports a single SATA device. The AMD SB950 South Bridge
supports RAID 0, RAID 1, RAID 5, RAID 10, and JBOD. Refer to Chapter 5, "Configuring SATA Hard Drive(s),"
for instructions on configuring a RAID array.
G.QBOFM G.QBOFM G.QBOFM
Pin No. Definition
SATA3 1 GND
2 TXP
7 1
3 TXN
7 1
4 GND
0 2 4 5 RXN
1 3 5 6 RXP
7 GND

• A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives
are to be used, the total number of hard drives must be an even number.
• A RAID 5 configuration requires at least three hard drives. (The total number of hard drives does
not have to be an even number.)
• A RAID 10 configuration requires four hard drives.
EBUG DEBUG Hardware Installation - 24 -
ORT PORT
7) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator
on the chassis to this header according to the pin assignments below. Note the positive and negative pins
before connecting the cables.
Message/Power/
Sleep LED Power Switch Speaker

MSG+

PW+

SPEAK+

SPEAK-
MSG-

PW-
2 20
1 19

HD-

RES+

CI+

PWR+

PWR-
HD+

RES-

CI-
Hard Drive Reset Power LED
Activity LED Switch
Chassis Intru-
sion Header

• MSG/PWR (Message/Power/Sleep LED, Yellow/Purple):

System Status LED Connects to the power status indicator on the chassis front panel. The LED
S0 On is on when the system is operating. The LED is off when the system is in S3/
S3/S4/S5 Off S4 sleep state or powered off (S5).

• PW (Power Switch, Red):

Connects to the power switch on the chassis front panel. You may configure the way to turn off your
system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management," for more
information).
• SPEAK (Speaker, Orange):
Connects to the speaker on the chassis front panel. The system reports system startup status by issuing
a beep code. One single short beep will be heard if no problem is detected at system startup.
• HD (Hard Drive Activity LED, Blue):
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
is reading or writing data.
• RES (Reset Switch, Green):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer
if the computer freezes and fails to perform a normal restart.
• CI (Chassis Intrusion Header, Gray):
Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has
been removed. This function requires a chassis with a chassis intrusion switch/sensor.

The front panel design may differ by chassis. A front panel module mainly consists of power switch,
reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis
front panel module to this header, make sure the wire assignments and the pin assignments are
matched correctly.
- 25 - Hardware Installation
8) F_AUDIO (Front Panel Audio Header)
The front panel audio header supports Intel High Definition audio (HD) and AC'97 audio. You may connect
your chassis front panel audio module to this header. Make sure the wire assignments of the module con-
nector match the pin assignments of the motherboard header. Incorrect connection between the module
connector and the motherboard header will make the device unable to work or even damage it.
For HD Front Panel Audio: For AC'97 Front Panel Audio:
Pin No. Definition Pin No. Definition
1 MIC2_L 1 MIC
9 1
2 GND 2 GND
F_AUDIO(H) F_PANEL(NH) F_PANEL
3 MIC2_R 3 MIC Power (H61M-D2)
4 -ACZ_DET 4 NC
10 2
5 LINE2_R 5 Line Out (R)
6 GND 6 NC
7 FAUDIO_JD 7 NC
8 No Pin 8 No Pin
9 LINE2_L 9 Line Out (L)
10 GND 10 NC

DB_PORT• The front panel audio header supports

BIOS Switcher HD audio by default. If your chassis provides an AC'97
(X58A-OC)
front panel audio module, refer to the instructions on how to activate AC'97 functionality via the
1

audio software in Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."

• Audio signals will be present on both of the front and back panel audio connections simultane-
1
1

ously. If you want to mute the back panel audio (only supported when using an HD front panel
audio module), refer to Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."
Voltage measurement
• Some module(X58A-OC)
chassis provide a front panel audio module that has separated connectors on each wire
PWM
instead of a single plug. For Switch (X58A-OC)
information about connecting the front panel audio module that has
1 2 3

different wire assignments, please contact the chassis manufacturer.

DIP

1 2 3

DIP

9) SPDIF_O (S/PDIF Out Header) DIP

1 2 3

DIP

This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion
1 2 3

cards) for connector

PCIe power digital audio output from your motherboard to certain expansion cards like graphics cards and
(SATA)(X58A-OC)
sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for
digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display
to the graphics card and have digital audio output from the HDMI display at the same time. For information
about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card.

Pin No. Definition

1 SPDIFO
1
2 GND

Hardware Installation - 26 -
 10) F_USB1/F_USB2/F_USB3 (USB 2.0/1.1 Headers)
The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an
UG
T optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

Pin No. Definition

1 Power (5V)
2 Power (5V)
9 1
10 2 3 USB DX-
4 USB DY-
5 USB DX+
6 USB DY+
7 GND
8 GND
9 No Pin
10 NC

11) F_USB30 (USB 3.0/2.0 Header)

The header conforms to USB 3.0/2.0 specification and can provide two USB ports. For purchasing the
optional 3.5" front panel that provides two USB 3.0/2.0 ports, please contact the local dealer.

1 10
F_USB30 F_AUDIO(H)

20 11

Pin No. Definition Pin No. Definition

1 VBUS 11 D2+
2 SSRX1- 12 D2-
3 SSRX1+ 13 GND
4 GND 14 SSTX2+
5 SSTX1- 15 SSTX2-
6 SSTX1+ 16 GND
BIOS
7 GND 17 SSRX2+DB_PORT
8 D1- 18 SSRX2-
9 D1+ 19 VBUS
10 NC 20 No Pin

When the system is in S4/S5 mode, only the USB ports routed to the F_USB1 header can support
Voltage measurement module(X58A-OC)
the ON/OFF Charge function. TPM
PW
w/housing
• Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB 2.0/1.1 header.
• Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord
from the power outlet to prevent damage to the USB bracket.
PCIe power connector (SATA)(X58A-OC)
- 27 - Hardware Installation
 12) F_1394 (IEEE 1394a Header)
The header conforms to IEEE 1394a specification. The IEEE 1394a header can provide one IEEE 1394a
UG
T port via an optional IEEE 1394a bracket. For purchasing the optional IEEE 1394a bracket, please contact
the local dealer.
Pin No. Definition
1 TPA+
9 1
2 TPA-
10 2 3 GND
4 GND
5 TPB+
6 TPB-
7 Power (12V)
8 Power (12V)
9 No Pin
10 GND

• Do not plug the USB bracket cable into the IEEE 1394a header.
• Prior to installing the IEEE 1394a bracket, be sure to turn off your computer and unplug the power
cord from the power outlet to prevent damage to the IEEE 1394a bracket.
• To connect an IEEE 1394a device, attach one end of the device cable to your computer and then
attach the other end of the cable to the IEEE 1394a device. Ensure that the cable is securely
connected.

13) COMA (Serial Port Header)

The COM header can provide one serial port via an optional COM port cable. For purchasing the optional
COM port cable, please contact the local dealer.

Pin No. Definition

1 NDCD-
2 NSIN
9 1 3 NSOUT
10 2 4 NDTR-
5 GND
6 NDSR-
7 NRTS-
8 NCTS-
9 NRI-
10 No Pin

Hardware Installation - 28 -
 BIOS S
DB_PORT
1

14) TPM (Trusted Platform Module Header)

You may connect a TPM (Trusted Platform Module) to this header.
19 1 Voltage measurement module(X58A-OC)
TPM
PWM
w/housing

20 2

Pin No. Definition Pin No. Definition 1

1 LCLK 11 LAD0 PCIe power connector (SATA)(X58A-OC)

2 GND 12 GND
3 LFRAME 13 NC
4 No Pin 14 ID
5 LRESET 15 SB3V
6 NC 16 SERIRQ
7 LAD3 17 GND
8 LAD2 18 NC
9 VCC3 19 NC
10 LAD1 20 SUSCLK

15) BAT (Battery)

The battery provides power to keep the values (such as BIOS configurations, date, and time information)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low
level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one minute.
(Or use a metal object like a screwdriver to touch the positive and negative
terminals of the battery holder, making them short for 5 seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer.

• Always turn off your computer and unplug the power cord before replacing the battery.
• Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with
an incorrect model.
• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
or uncertain about the battery model.
• When installing the battery, note the orientation of the positive side (+) and the negative side (-)
of the battery (the positive side should face up).
• Used batteries must be handled in accordance with local environmental regulations.

- 29 - Hardware Installation
16) CLR_CMOS (Clear CMOS Jumper)
Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the
CMOS values to factory defaults. To clear the CMOS values, use a metal object like a screwdriver to touch
the two pins for a few seconds.

Open: Normal

Short: Clear CMOS Values

•• Always turn off your computer and unplug the power cord from the power outlet before clearing
the CMOS values.
•• After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or
manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations).

Hardware Installation - 30 -
Chapter 2 BIOS Setup
BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the
motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,
saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows
the user to modify basic system configuration settings or to activate certain system features.

When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to
keep the configuration values in the CMOS.

To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.

To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.
•• Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.
•• @BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet
and updates the BIOS.
For instructions on using the Q-Flash and @BIOS utilities, refer to Chapter 4, "BIOS Update Utilities."
•• Because BIOS flashing is potentially risky, if you do not encounter problems using the current
version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with
caution. Inadequate BIOS flashing may result in system malfunction.
•• It is recommended that you not alter the default settings (unless you need to) to prevent system
instability or other unexpected results. Inadequately altering the settings may result in system's
failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values.
(Refer to the "Load Optimized Defaults" section in this chapter or introductions of the battery/clear
CMOS jumper in Chapter 1 for how to clear the CMOS values.)

- 31 - BIOS Setup
2-1 Startup Screen
The following startup Logo screen will appear when the computer boots.

Function Keys

Function Keys:
<DEL>: BIOS SETUP\Q-FLASH
Press the <Delete> key to enter BIOS Setup or to access the Q-Flash utility in BIOS Setup.
<F9>: SYSTEM INFORMATION
Press the <F9> key to display your system information.
<F12>: BOOT MENU
Boot Menu allows you to set the first boot device without entering BIOS Setup. In Boot Menu, use the up
arrow key <h> or the down arrow key <i> to select the first boot device, then press <Enter> to accept.
The system will boot from the device immediately.
Note: The setting in Boot Menu is effective for one time only. After system restart, the device boot order
will still be based on BIOS Setup settings.
<END>: Q-FLASH
Press the <End> key to access the Q-Flash utility directly without having to enter BIOS Setup first.

BIOS Setup - 32 -
2-2 The Main Menu
The Main Menu
On the main menu of the BIOS Setup program, press arrow keys to move among the items and press <Enter>
to accept or enter a sub-menu. Or you can use your mouse to select the item you want.
(Sample BIOS Version: E11)

Setup Menus

Enter Q-Flash

Help

Function Keys

Configuration Items Current Settings

BIOS Setup Program Function Keys

<f><g> Move the selection bar to select a setup menu
<h><i> Move the selection bar to select an configuration item on a menu
<Enter> Execute command or enter a menu
<+>/<Page Up> Increase the numeric value or make changes
<->/<Page Down> Decrease the numeric value or make changes
<F5> Restore the previous BIOS settings for the current submenus
<F7> Load the Optimized BIOS default settings for the current submenus
<F8> Access the Q-Flash utility
<F9> Display system information
<F10> Save all the changes and exit the BIOS Setup program
<F12> Capture the current screen as an image and save it to your USB drive
<Esc> Main Menu: Exit the BIOS Setup program
Submenus: Exit current submenu

- 33 - BIOS Setup
BIOS Setup Menus
„„ M.I.T.
Use this menu to configure the clock, frequency, and voltages of your CPU and memory, etc. Or check the
system/CPU temperatures, voltages, and fan speeds.
„„ System
Use this menu to configure the default language used by the BIOS and system time and date. This menu
also displays information on the devices connected to the SATA ports.
„„ BIOS Features
Use this menu to configure the device boot order, advanced features available on the CPU, and the primary
display adapter.
„„ Peripherals
Use this menu to configure all peripheral devices, such as SATA, USB, integrated audio, and integrated
LAN, etc.
„„ Power Management
Use this menu to configure all the power-saving functions.
„„ Save & Exit
Save all the changes made in the BIOS Setup program to the CMOS and exit BIOS Setup. You can save
the current BIOS settings to a profile or load optimized defaults for optimal-performance system operations.

•• When the system is not stable as usual, select the Load Optimized Defaults item to set your
system to its defaults.
•• The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS
version.

BIOS Setup - 34 -
2-3 M.I.T.

Whether the system will work stably with the overclock/overvoltage settings you made is dependent
on your overall system configurations. Incorrectly doing overclock/overvoltage may result in damage
to CPU, chipset, or memory and reduce the useful life of these components. This page is for advanced
users only and we recommend you not to alter the default settings to prevent system instability or
other unexpected results. (Inadequately altering the settings may result in system's failure to boot. If
this occurs, clear the CMOS values and reset the board to default values.)

This section provides information on the BIOS version, CPU base clock, CPU frequency, memory frequency,
total memory size, CPU temperature, Vcore, and memory voltage.

- 35 - BIOS Setup
`` M.I.T. Current Status
This screen provides information on CPU/memory frequencies/parameters.

`` Advanced Frequency Settings

&& BCLK Clock Control

Allows you to manually set the CPU base clock in 1 MHz increments. (Default: Auto)
Important: It is highly recommended that the CPU frequency be set in accordance with the CPU
specifications.
&& CPU NorthBridge Frequency
Allows you to manually set the CPU North Bridge frequency. The adjustable range is from 1000 MHz
to 3200 MHz.
&& HT Link Frequency
Allows you to manually set the frequency for the HT Link between the CPU and chipset.The adjustable
range is from 200 MHz to 3200 MHz.

&& CPU Clock Ratio

Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU
being installed.
&& CPU Frequency
Displays the current operating CPU frequency.

BIOS Setup - 36 -
`` Advanced CPU Core Features

&& CPU Clock Ratio, CPU Frequency

The settings above are synchronous to those under the same items on the Advanced Frequency Settings
menu.
&& Core Performance Boost (Note)
Allows you to determine whether to enable the Core Performance Boost (CPB) technology, a CPU
performance-boost technology. (Default: Auto)
&& CPB Ratio (Note)
Allows you alter the ratio for the CPB. The adjustable range is dependent on the CPU being installed.
(Default: Auto)
&& CPU Unlock (Note)
Allows you to determine whether unlock hidden CPU cores. (Default: Disabled)
&& Cool&Quiet

Enabled  Lets the AMD Cool'n'Quiet driver dynamically adjust the CPU clock and VID to
reduce heat output from your computer and its power consumption. (Default)

Disabled Disables this function.
&& C1E Support
Allows you to determine whether to let the CPU enter C1 mode in system halt state. When enabled, the
CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.
(Default: Enabled)
&& SVM
Virtualization enhanced by Virtualization Technology will allow a platform to run multiple operating systems
and applications in independent partitions. With virtualization, one computer system can function as multiple
virtual systems. (Default: Enabled)
&& CPU core Control (Note)
Allows you to determine whether to manually enable/disable CPU cores. Automatic mode allows the BIOS
to enable all CPU cores (number of cores available depends on the CPU being used).(Default: Automatic
mode)
(Note) This item is present only when you install a CPU that supports this feature.

- 37 - BIOS Setup
&& Core C6 State (Note 1)
Allows you to determine whether to let the CPU enter C6 mode in system halt state. When enabled, the
CPU core frequency will be reduced during system halt state to decrease power consumption. The C6
state is a more enhanced power-saving state than C1. (Default: Enabled)
&& HPC Mode (Note 1)
Allows you to determine whether to enable High Performance Computing (HPC) mode for the CPU. Enabled
prevents the CPU frequency from being lowered during system halt state. (Default: Disabled)
&& Extreme Memory Profile (X.M.P.) (Note 2)
Allows the BIOS to read the SPD data on XMP memory module(s) to enhance memory performance when
enabled.

Disabled Disables this function. (Default)

Profile1 Uses Profile 1 settings.

Profile2 (Note 2)
Uses Profile 2 settings.
&& System Memory Multiplier (SPD)
Allows you to set the system memory multiplier. Auto sets memory multiplier according to memory SPD
data. (Default: Auto)
&& Memory Frequency (MHz)
This value is automatically adjusted according to the BCLK Clock Control and System Memory Multiplier
settings.
`` Advanced Memory Settings

&& Extreme Memory Profile (X.M.P.) (Note 2), System Memory Multiplier, Memory
Frequency(Mhz)
The settings above are synchronous to those under the same items on the Advanced Frequency Settings
menu.
&& Performance Enhance
Allows the system to operate at three different performance levels.

Normal Lets the system operate at its basic performance level.

Turbo Lets the system operate at its good performance level. (Default)

Extreme Lets the system operate at its best performance level.
(Note 1) This item is present only when you install a CPU that supports this feature.
(Note 2) This item is present only when you install a memory module that supports this feature.
BIOS Setup - 38 -
&& DRAM Timing Selectable
Quick and Expert allows the memory timing settings below to be configurable. Options are: Auto (default),
Quick, Expert.
&& Profile DDR Voltage
When using a non-XMP memory module or Extreme Memory Profile (X.M.P.) is set to Disabled, this item
will display as 1.50V. When Extreme Memory Profile (X.M.P.) is set to Profile1 or Profile2, this item will
display the value based on the SPD data on the XMP memory.
&& Profile VTT Voltage
The value displayed here is dependent on the CPU being used.
&& Channel Interleaving
Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access
different channels of the memory to increase memory performance and stability. Auto lets the BIOS
automatically configure this setting. (Default: Auto)
&& Rank Interleaving
Enables or disables memory rank interleaving. Enabled allows the system to simultaneously access different
ranks of the memory to increase memory performance and stability. Auto lets the BIOS automatically
configure this setting. (Default: Auto)

`` Channel A/B Timing Settings

This sub-menu provides memory timing settings for each channel of memory. The respective timing setting
screens are configurable only when DRAM Timing Selectable is set to Quick or Expert. Note: Your system
may become unstable or fail to boot after you make changes on the memory timings. If this occurs, please reset
the board to default values by loading optimized defaults or clearing the CMOS values.

- 39 - BIOS Setup
`` Advanced Voltage Settings

This sub-menu allows you to set CPU, Chipset, and memory voltages.

`` PC Health Status

BIOS Setup - 40 -
&& Reset Case Open Status

Disabled Keeps or clears the record of previous chassis intrusion status. (Default)

Enabled Clears the record of previous chassis intrusion status and the Case Open field will show
"No" at next boot.
&& Case Open
Displays the detection status of the chassis intrusion detection device attached to the motherboard CI
header. If the system chassis cover is removed, this field will show "Yes", otherwise it will show "No". To
clear the chassis intrusion status record, set Reset Case Open Status to Enabled, save the settings to
the CMOS, and then restart your system.
&& CPU Vcore/Dram Voltage/+3.3V/+5V/+12V
Displays the current system voltages.
&& CPU/System Temperature
Displays current CPU/system temperature.
&& CPU/System/Power Fan Speed
Displays current CPU/system/power fan speed.
&& CPU Warning Temperature
Sets the warning threshold for CPU temperature. When CPU temperature exceeds the threshold, BIOS
will emit warning sound. Options are: Disabled (default), 60oC/140oF, 70oC/158oF, 80oC/176oF, 90oC/194oF.
&& CPU/System/Power Fan Fail Warning
Allows the system to emit warning sound if the fan is not connected or fails. Check the fan condition or fan
connection when this occurs. (Default: Disabled)
&& CPU Fan Control Mode

Auto  Lets the BIOS automatically detect the type of CPU fan installed and sets the optimal CPU
fan control mode. (Default)

Voltage Sets Voltage mode for a 3-pin CPU fan.

PWM Sets PWM mode for a 4-pin CPU fan.

- 41 - BIOS Setup
&& CPU Fan Speed Control
Allows you to determine whether to enable the CPU fan speed control function and adjust the fan speed.

Normal  Allows the CPU fan to run at different speeds according to the CPU temperature. You can
adjust the fan speed with EasyTune based on your system requirements. (Default)

Silent Allows the CPU fan to run at slow speeds.

Manual Allows you to control the CPU fan speed under the Slope PWM item.

Disabled Allows the CPU fan to run at full speeds.
&& Slope PWM
Allows you to control the CPU fan speed. This item is configurable only when CPU Fan Speed Control is
set to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC.
&& 1st System Fan Speed Control (SYS_FAN1 Connector)
Allows you to determine whether to enable the system fan speed control function for the system fan
connected to the SYS_FAN1 connector and adjust the fan speed.

Normal  Allows the system fan to run at different speeds according to the system temperature. You
can adjust the fan speed with EasyTune based on your system requirements. (Default)

Silent Allows the system fan to run at slow speeds.

Manual Allows you to control the system fan speed under the Slope PWM item.

Disabled Allows the system fan to run at full speeds.
&& Slope PWM
Allows you to control the system fan speed. This item is configurable only when 1st System Fan Speed
Control is set to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC.

BIOS Setup - 42 -
2-4 System

This section provides information on your motherboard model and BIOS version. You can also select the default
language used by the BIOS and manually set the system time.

&& System Language

Selects the default language used by the BIOS.
&& System Date
Sets the system date. The date format is week (read-only), month, date, and year. Use <Enter> to switch
between the Month, Date, and Year fields and use the <Page Up> or <Page Down> key to set the desired
value.
&& System Time
Sets the system time. The time format is hour, minute, and second. For example, 1 p.m. is 13:0:0. Use
<Enter> to switch between the Hour, Minute, and Second fields and use the <Page Up> or <Page Down>
key to set the desired value.
&& Access Level
Displays the current access level depending on the type of password protection used. (If no password is
set, the default will display as Administrator.) The Administrator level allows you to make changes to all
BIOS settings; the User level only allows you to make changes to certain BIOS settings but not all.

`` ATA Port Information

This section provides information on the device connected to each SATA port controlled by AMD Chipset.

- 43 - BIOS Setup
2-5 BIOS Features

&& Boot Option Priorities

Specifies the overall boot order from the available devices. For example, you can set hard drive as the
first priority (Boot Option #1) and DVD ROM drive as the second priority (Boot Option #2). The list only
displays the device with the highest priority for a specific type. For example, only hard drive defined as the
first priority on the Hard Drive BBS Priorities submenu will be presented here.
Removable storage devices that support GPT format will be prefixed with "UEFI:" string on the boot device
list. To boot from an operating system that supports GPT partitioning, select the device prefixed with "UEFI:"
string.
Or if you want to install an operating system that supports GPT partitioning such as Windows 7 64-bit, select
the optical drive that contains the Windows 7 64-bit installation disk and is prefixed with "UEFI:" string.
BIOS Setup - 44 -
&& Hard Drive/CD/DVD ROM Drive/Floppy Drive/Network Device BBS Priorities
Specifies the boot order for a specific device type, such as hard drives, optical drives, floppy disk drives,
and devices that support Boot from LAN function, etc. Press <Enter> on this item to enter the submenu that
presents the devices of the same type that are connected. This item is present only if at least one device
for this type is installed.
&& Bootup NumLock State
Enables or disables Numlock feature on the numeric keypad of the keyboard after the POST. (Default:
Enabled)
&& Security Option
Specifies whether a password is required every time the system boots, or only when you enter BIOS Setup.
After configuring this item, set the password(s) under the Administrator Password/User Password item.

Setup  A password is only required for entering the BIOS Setup program.

System A password is required for booting the system and for entering the BIOS Setup program.
(Default)
&& Full Screen LOGO Show
Allows you to determine whether to display the GIGABYTE Logo at system startup. Disabled skips the
GIGABYTE Logo when the system starts up. (Default: Enabled)
&& CSM Support
Enables or disables UEFI CSM (Compatibility Support Module) to support a legacy PC boot process.

Always Enables UEFI CSM. (Default)

Never Disables UEFI CSM and supports UEFI BIOS boot process only.
&& Boot Mode Selection
Allows you to select which type of operating system to boot.
UEFI and LegacyAllows booting from operating systems that support legacy option ROM or UEFI option
ROM. (Default)

Legacy Only Allows booting from operating systems that only support legacy Option ROM.

UEFI Only Allows booting from operating systems that only support UEFI Option ROM.
This item is configurable only when CSM Support is set to Always.
&& LAN PXE Boot Option ROM
Allows you to decide whether to enable the legacy option ROM for the LAN controller. (Default: Disabled)
This item is configurable only when CSM Support is set to Always.
&& Storage Boot Option Control
Allows you to select whether to enable the UEFI or legacy option ROM for the storage device controller.

Disabled Disables option ROM.

Legacy Only Enables legacy option ROM only. (Default)

UEFI Only Enables UEFI option ROM only.

Legacy First Enables legacy option ROM first.

UEFI First Enables UEFI option ROM first.
This item is configurable only when CSM Support is set to Always.
&& Display Boot Option Control
Allows you to select whether to enable the UEFI or legacy option ROM for the graphics controller.

Disabled Disables option ROM.

Legacy Only Enables legacy option ROM only. (Default)

UEFI Only Enables UEFI option ROM only.

Legacy First Enables legacy option ROM first.

UEFI First Enables UEFI option ROM first.
This item is configurable only when CSM Support is set to Always.
- 45 - BIOS Setup
&& Other PCI Device ROM Priority
Allows you to select whether to enable the UEFI or Legacy option ROM for the PCI device controller other
than the LAN, storage device, and graphics controllers.

Legacy OpROM Enables legacy option ROM only.

UEFI OpROM Enables UEFI option ROM only. (Default)
&& Network stack
Disables or enables booting from the network to install a GPT format OS, such as installing the OS from
the Windows Deployment Services server. (Default: Disable)
&& Ipv4 PXE Boot Support
Enables or disables IPv4 PXE Support. This item is configurable only when Network stack is enabled.
&& Ipv6 PXE Boot Support
Enables or disables IPv6 PXE Support. This item is configurable only when Network stack is enabled.

&& Administrator Password

Allows you to configure an administrator password. Press <Enter> on this item, type the password, and
then press <Enter>. You will be requested to confirm the password. Type the password again and press
<Enter>. You must enter the administrator password (or user password) at system startup and when entering
BIOS Setup. Differing from the user password, the administrator password allows you to make changes to
all BIOS settings.
&& User Password
Allows you to configure a user password. Press <Enter> on this item, type the password, and then press
<Enter>. You will be requested to confirm the password. Type the password again and press <Enter>.
You must enter the administrator password (or user password) at system startup and when entering BIOS
Setup. However, the user password only allows you to make changes to certain BIOS settings but not all.

To cancel the password, press <Enter> on the password item and when requested for the password, enter the
correct one first. When prompted for a new password, press <Enter> without entering any password. Press
<Enter> again when prompted to confirm.

BIOS Setup - 46 -
2-6 Peripherals

&& Init Display First

Specifies the first initiation of the monitor display from the PCI Express or PCI graphics cards .

PCIe 1 Slot Sets the graphics card on the PCIEX16_1 slot as the first display. (Default)

PCIe 2 Slot Sets the graphics card on the PCIEX16_2 slot as the first display.

PCIe 3 Slot Sets the graphics card on the PCIEX4_1slot as the first display.

PCIe 4 Slot Sets the graphics card on the PCIEX4_2 slot as the first display.

PCI Sets the graphics card on the PCI slot as the first display.
&& VIA 1394 Controller
Enables or disables the onboard IEEE 1394 function. (Default: Enabled)
&& OnChip SATA Controller
Enables or disables the integrated SATA controllers. (Default: Enabled)
&& OnChip SATA Type
Enables or disables RAID for the SATA controllers integrated in the AMD Chipset or configures the SATA
controllers to AHCI mode.

Native IDE Configures the SATA controller to IDE mode.

RAID Enables RAID for the SATA controller.

AHCI Configures the SATA controllers to AHCI mode. Advanced Host Controller Interface
(AHCI) is an interface specification that allows the storage driver to enable advanced
Serial ATA features such as Native Command Queuing and hot plug. (Default)
&& OnChip SATA Port4/5 Type (SATA3 4/SATA3 5 connectors)
This option is configurable only when OnChip SATA Type is set to RAID or AHCI. Configures the operating
mode of the integrated SATA3 4 and SATA3 5 connectors.
 SATA Type The mode depends on the OnChip SATA Type settings.
As

IDE Disables RAID for the SATA controller and configures the SATA controller to IDE mode.
(Default)

- 47 - BIOS Setup
&& HD Audio Azalia Device
Enables or disables the onboard audio function. (Default: Enabled)
If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to
Disabled.
&& OnBoard USB device
Enables or disables the integrated USB controller. (Default: Enabled)
&& Onboard LAN Controller
Enables or disables the onboard LAN function. (Default: Enabled)
If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to
Disabled.
&& F_USB30 Controller (Etron EJ168 USB Controller, USB 3.0/2.0 ports routed to the
onboard F_USB30 header)
Enables or disables the Etron EJ168 USB controller. (Default: Enabled)
&& R_USB3.0 Controller (Etron EJ168 USB Controller, USB 3.0/2.0 ports on the back
panel)
Enables or disables the Etron EJ168 USB controller. (Default: Enabled)
&& Onboard eSATA Controller (Marvell 88SE9172 Chip, eSATA Connectors on the Back
Panel)
Enables or disables the SATA controller integrated in the Marvell 88SE9172 chip. (Default: Enabled)
&& Legacy USB Support
Allows USB keyboard/mouse to be used in MS-DOS. (Default: Enabled)
&& XHCI Hand-off
Determines whether to enable XHCI Hand-off feature for an operating system without XHCI Hand-off
support. (Default: Enabled)
&& EHCI Hand-off
Determines whether to enable EHCI Hand-off feature for an operating system without EHCI Hand-off
support. (Default: Disabled)
&& Port 60/64 Emulation
Enables or disables emulation of I/O ports 64h and 60h. This should be enabled for full legacy support
for USB keyboards/mice in MS-DOS or in operating system that does not natively support USB devices.
(Default: Disabled)
&& USB Storage Devices
Displays a list of connected USB mass storage devices. This item appears only when a USB storage device
is installed.
&& IOMMU Controller
Enables or disables AMD IOMMU support. (Default: Enabled)

`` Trusted Computing
&& TPM SUPPORT
Enables or disables Trusted Platform Module (TPM). Set this item to Enable when a TPM device is installed.
(Default: Disable)

BIOS Setup - 48 -
`` SB SATA Configuration

&& PORT0 Hot Plug~PORT5 Hot Plug

Enables or disable the hot plug capability for each SATA port. (Default: Disabled)
&& SATA Power on PORT0~SATA Power on PORT5
Enables or disables each SATA port. (Default: Enabled)

`` Marvell ATA Controller Configuration

&& GSATA Controller (Marvell 88SE9172 Chip, eSATA connectors)

Enables or disables RAID for the SATA controller integrated in the Marvell 88SE9172 chip or configures
the SATA controller to AHCI mode. The area below displays the current status of the two SATA ports.
 Mode
IDE Disables RAID for the SATA controllers and configures the SATA controllers to IDE
mode.
- 49 - BIOS Setup
 
AHCI Mode Configures the SATA controllers to AHCI mode. Advanced Host Controller Interface (AHCI)
is an interface specification that allows the storage driver to enable advanced Serial ATA
features such as Native Command Queuing and hot plug. (Default)

RAID Mode Enables RAID for the SATA controllers.

Disabled Disables this function.

`` Super IO Configuration
This section provides information on the super I/O chip and allows you to configure the serial port.
&& Serial Port A
Enables or disables the onboard serial port. (Default: Enabled)

BIOS Setup - 50 -
2-7 Power Management

&& Resume by Alarm

Determines whether to power on the system at a desired time. (Default: Disabled)
If enabled, set the date and time as following:

Wake up day: Turn on the system at a specific time on each day or on a specific day in a month.

Wake up hour/minute/second: Set the time at which the system will be powered on automatically.
Note: When using this function, avoid inadequate shutdown from the operating system or removal of the
AC power, or the settings may not be effective.
&& HPET Support (Note)
Enables or disables High Precision Event Timer (HPET) for Windows 7/Vista operating system. (Default:
Enabled)
&& Soft-Off by PWR-BTTN
Configures the way to turn off the computer in MS-DOS mode using the power button.

Instant-Off Press the power button and then the system will be turned off instantly. (Default)

Delay 4 Sec Press and hold the power button for 4 seconds to turn off the system. If the power
button is pressed for less than 4 seconds, the system will enter suspend mode.
&& AC BACK
Determines the state of the system after the return of power from an AC power loss.

Memory The system returns to its last known awake state upon the return of the AC power.

Always On The system is turned on upon the return of the AC power.

Always Off The system stays off upon the return of the AC power. (Default)
&& Power On By Keyboard
Allows the system to be turned on by a PS/2 keyboard wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.

Disabled Disables this function. (Default)

Password Set a password with 1~5 characters to turn on the system.

Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system.
 Key
Any Press any key to turn on the system.
(Note) Supported on Windows 7/Vista operating system only.
- 51 - BIOS Setup
&& Power On Password
Set the password when Power On By Keyboard is set to Password.
Press <Enter> on this item and set a password with up to 5 characters and then press <Enter> to accept.
To turn on the system, enter the password and press <Enter>.
Note: To cancel the password, press <Enter> on this item. When prompted for the password, press <Enter>
again without entering the password to clear the password settings.
&& Power On By Mouse
Allows the system to be turned on by a PS/2 mouse wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.

Disabled Disables this function. (Default)

Move Move the mouse to turn on the system.

Double Click Double click on left button on the mouse to turn on the system.
&& ErP
Determines whether to let the system consume least power in S5 (shutdown) state. (Default: Disabled)
Note: When this item is set to Enabled, the following functions will become unavailable: PME event wake
up, power on by mouse, power on by keyboard, and wake on LAN.

BIOS Setup - 52 -
2-8 Save & Exit

&& Save & Exit Setup

Press <Enter> on this item and select Yes. This saves the changes to the CMOS and exits the BIOS Setup
program. Select No or press <Esc> to return to the BIOS Setup Main Menu.
&& Exit Without Saving
Press <Enter> on this item and select Yes. This exits the BIOS Setup without saving the changes made
in BIOS Setup to the CMOS. Select No or press <Esc> to return to the BIOS Setup Main Menu.
&& Load Optimized Defaults
Press <Enter> on this item and select Yes to load the optimal BIOS default settings. The BIOS defaults
settings help the system to operate in optimum state. Always load the Optimized defaults after updating
the BIOS or after clearing the CMOS values.
&& Boot Override
Allows you to select a device to boot immediately. Press <Enter> on the device you select and select Yes
to confirm. Your system will restart automatically and boot from that device.
&& Save Profiles
This function allows you to save the current BIOS settings to a profile. You can create up to 8 profiles and
save as Setup Profile 1~ Setup Profile 8. Press <Enter> to complete. Or you can select Select File in
HDD/USB/FDD to save the profile to your storage device.
&& Load Profiles
If your system becomes unstable and you have loaded the BIOS default settings, you can use this function
to load the BIOS settings from a profile created before, without the hassles of reconfiguring the BIOS
settings. First select the profile you wish to load and then press <Enter> to complete. You can select Select
File in HDD/USB/FDD to input the profile previously created from your storage device or load the profile
automatically created by the BIOS, such as reverting the BIOS settings to the last settings that worked
properly (last known good record).

- 53 - BIOS Setup
BIOS Setup - 54 -
 Chapter 3 Drivers Installation
•• Before installing the drivers, first install the operating system.
•• After installing the operating system, insert the motherboard driver disk into your optical drive.
The driver Autorun screen is automatically displayed which looks like that shown in the screen
shot below. (If the driver Autorun screen does not appear automatically, go to My Computer,
double-click the optical drive and execute the Run.exe program.)

3-1 Installing Chipset Drivers

After inserting the driver disk, "Xpress Install" will automatically scan your system and then list all the drivers
that are recommended to install. You can click the Install All button and "Xpress Install" will install all the rec-
ommended drivers. Or click Install Single Items to manually select the drivers you wish to install.

•• Please ignore the popup dialog box(es) (e.g. the Found New Hardware Wizard) displayed
when "Xpress Install" is installing the drivers. Failure to do so may affect the driver installation.
•• Some device drivers will restart your system automatically during the driver installation. After the
system restart, "Xpress Install" will continue to install other drivers.
•• After "Xpress Install" installs all of the drivers, a dialog box will appear asking whether to install
new GIGABYTE utilities. Click Yes to automatically install the utilities. Or click No if you want to
manually select the utilities to install on the Application Software page later.
•• For USB 2.0 driver support under the Windows XP operating system, please install the Windows
XP Service Pack 1 or later. After installing the SP1 (or later), if a question mark still exists in
Universal Serial Bus Controller in Device Manager, please remove the question mark (by
right-clicking your mouse and select Uninstall) and restart the system. (The system will then
autodetect and install the USB 2.0 driver.)

- 55 - Drivers Installation
3-2 Application Software
This page displays all the utilities and applications that GIGABYTE develops and some free software. You
can click the Install button on the right of an item to install it.

3-3 Technical Manuals

This page provides the content descriptions for this driver disk.

Drivers Installation - 56 -
3-4 Contact
For the detailed contact information of the GIGABYTE Taiwan headquarter or worldwide branch offices, click
the URL on this page to link to the GIGABYTE website.

3-5 System
This page provides the basic system information.

- 57 - Drivers Installation
3-6 Download Center
To update the BIOS, drivers, or applications, click the Download Center button to link to the GIGABYTE
website. The latest version of the BIOS, drivers, or applications will be displayed.

3-7 New Program

This page provides a quick link to GIGABYTE's lately developed utilities for users to install. You can click the
Install button on the right of an item to install it.

Drivers Installation - 58 -
Chapter 4 Unique Features
4-1 BIOS Update Utilities
GIGABYTE motherboards provide two unique BIOS update tools, Q-Flash™ and @BIOS™. GIGABYTE Q-Flash
and @BIOS are easy-to-use and allow you to update the BIOS without the need to enter MS-DOS mode.
Additionally, this motherboard features the DualBIOS™ design, which enhances protection for the safety and
stability of your computer by adding one more physical BIOS chip.

What is DualBIOS™?
Motherboards that support DualBIOS have two BIOS onboard, a main BIOS and
a backup BIOS. Normally, the system works on the main BIOS. However, if the
main BIOS is corrupted or damaged, the backup BIOS will take over on the next system boot and copy the
BIOS file to the main BIOS to ensure normal system operation. For the sake of system safety, users cannot
update the backup BIOS manually.

What is Q-Flash™?
With Q-Flash you can update the system BIOS without having to enter operating
systems like MS-DOS or Window first. Embedded in the BIOS, the Q-Flash tool
frees you from the hassles of going through complicated BIOS flashing process.

What is @BIOS™?
@BIOS allows you to update the system BIOS while in the Windows environment.
@BIOS will download the latest BIOS file from the nearest @BIOS server site
and update the BIOS.

4-1-1 Updating the BIOS with the Q-Flash Utility

A. Before You Begin
1. From GIGABYTE's website, download the latest compressed BIOS update file that matches your
motherboard model.
2. Extract the file and save the new BIOS file (e.g. 9FXAUD33.F1) to your USB flash drive or hard drive.
Note: The USB flash drive or hard drive must use FAT32/16/12 file system.
3. Restart the system. During the POST, press the <End> key to enter Q-Flash. Note: You can access Q-Flash
by either pressing the <End> key during the POST or pressing the <F8> key in BIOS Setup. However, if the
BIOS update file is saved to a hard drive in RAID/AHCI mode or a hard drive attached to an independent
SATA controller, use the <End> key during the POST to access Q-Flash.

Because BIOS flashing is potentially risky, please do it with caution. Inadequate BIOS flashing may
result in system malfunction.

- 59 - Unique Features
B. Updating the BIOS
In the main menu of Q-Flash, use the keyboard or mouse to select an item to execute. When updating the
BIOS, choose the location where the BIOS file is saved. The following procedure assumes that you save the
BIOS file to a USB flash drive.

Step 1:
1. Insert the USB flash drive containing the BIOS file into the computer. In the main menu of Q-Flash, select
Update BIOS From Drive.
•• The Save BIOS to Drive option allows you to save the current BIOS file.
•• Q-Flash only supports USB flash drive or hard drives using FAT32/16/12 file system.
•• If the BIOS update file is saved to a hard drive in RAID/AHCI mode or a hard drive attached to
an independent SATA controller, use the <End> key during the POST to access Q-Flash.

2. Select USB Flash Drive.

Q-Flash Utility v1.05
Model Name : 990FXA-UD3
BIOS Version : E6
BIOS Date : 09/27/2012
Flash Type/Size : MXIC 25L3206E 4MB
Update BIOS From Drive
Save BIOS
Select to Drive
Device
Return to BIOS setup
USB Flash Drive

3. Select the BIOS update file.

Make sure the BIOS update file matches your motherboard model.

Step 2:
The process of the system reading the BIOS file from the USB flash drive is displayed on the screen. When
the message "Are you sure to update BIOS?" appears, select Yes to begin the BIOS update. The monitor will
display the update process.
•• Do not turn off or restart the system when the system is reading/updating the BIOS.
•• Do not remove the USB flash drive or hard drive when the system is updating the BIOS.

Step 3:
When the update process is complete, select Reboot to reboot the system.

Q-Flash

BIOS update is completed.

Power off
Reboot

Unique Features - 60 -
Step 4:
During the POST, press <Delete> to enter BIOS Setup. Select Load Optimized Defaults on the Save & Exit
screen and press <Enter> to load BIOS defaults. System will re-detect all peripheral devices after a BIOS update,
so we recommend that you reload BIOS defaults.

Select Yes to load BIOS defaults

Step 5:
Select Save & Exit Setup and press <Enter>. And then select Yes to save settings to CMOS and exit BIOS
Setup. The procedure is complete after the system restarts.

- 61 - Unique Features
4-1-2 Updating the BIOS with the @BIOS Utility
A. Before You Begin
1. In Windows, close all applications and TSR (Terminate and Stay Resident) programs. This helps prevent
unexpected failures when performing a BIOS update.
2. During the BIOS update process, ensure the Internet connection is stable and do NOT interrupt the Internet
connection (for example, avoid a power loss or switching off the Internet). Failure to do so may result in a
corrupted BIOS or a system that is unable to start.
3. Do not use the G.O.M. (GIGABYTE Online Management) function when using @BIOS.
4. GIGABYTE product warranty does not cover any BIOS damage or system failure resulting from an
inadequate BIOS flashing.

B. Using @BIOS

1. Update the BIOS Using the Internet Update Function:

Click Update BIOS from GIGABYTE Server, select the @BIOS server site closest to your location and
then download the BIOS file that matches your motherboard model. Follow the on-screen instructions to
complete.
If the BIOS update file for your motherboard is not present on the @BIOS server site, please
manually download the BIOS update file from GIGABYTE's website and follow the instructions in
"Update the BIOS without Using the Internet Update Function" below.
2. Update the BIOS without Using the Internet Update Function:
Click Update BIOS from File, then select the location where you save the BIOS update file obtained from
the Internet or through other source. Follow the on-screen instructions to complete.

3. Save the Current BIOS File:

Click Save Current BIOS to File to save the current BIOS file.

4. Load BIOS Defaults after BIOS Update:

Select the Load CMOS default after BIOS update check box and then the system will automatically load
BIOS defaults after BIOS update and after the system restarts.

C. After Updating the BIOS

Restart your system after updating the BIOS.

Make sure that the BIOS file to be flashed matches your motherboard model. Updating the
BIOS with an incorrect BIOS file could cause your system not to boot.

Unique Features - 62 -
4-2 EasyTune 6
GIGABYTE's EasyTune 6 is a simple and easy-to-use interface that allows users to fine-tune their system
settings or do overclock/overvoltage in Windows environment. The user-friendly EasyTune 6 interface also
includes tabbed pages for CPU and memory information, letting users read their system-related information
without the need to install additional software.

The EasyTune 6 Interface

Tabs Information
Tab Function
The CPU tab provides information on the installed CPU and motherboard.
The Memory tab provides information on the installed memory module(s). You can select memory
module on a specific slot to see its information.
The Tuner tab allows you to change memory settings and voltages.
•• Easy mode provides information on CPU/memory.
•• Advanced mode allows you to individually change system clock settings and voltages settings
using the sliders.
•• Easy Boost is an easy-to-use auto-overclocking function (Note). When activated, the system
automatically experiments all sorts of overclocking configurations till it hangs. After restart,
the system will operate with the optimum configurations tested to let the CPU reach the best
overclocking performance.
•• Save allows you to save the current settings to a new profile (.txt file).
•• Load allows you to load previous settings from a profile.
After making changes in Easy mode/Advanced mode, be sure to click Set for these changes to take
effect or click Default to restore to default values.
The Graphics tab allows you to change the core clock and memory clock for your AMD or NVIDIA
graphics card.
The Smart tab allows you to specify a Smart Fan mode. Smart Fan Advanced mode allows the fan
speed to be changed linearly based on the temperature thresholds you set.
The HW Monitor tab allows you to monitor hardware temperature, voltage and fan speed and set
temperature/fan speed alarm. You can choose the alert sound from the buzzer or use your own sound
file (.wav file).
(Note) Before enabling Easy Boost, right-click the EasyTune 6 icon in the notification area. Select Auto overclock last
tune on the next reboot to allow the system to work with the optimum overclocking configuration after restart.
Available functions in EasyTune 6 may differ by motherboard model. Grayed-out area(s) indicates that the item is not
configurable or the function is not supported.
Incorrectly doing overclock/overvoltage may result in damage to the hardware components such as CPU, chipset, and
memory and reduce the useful life of these components. Before you do the overclock/overvoltage, make sure that you
fully know each function of EasyTune 6, or system instability or other unexpected results may occur.

- 63 - Unique Features
4-3 Q-Share
Q-Share is an easy and convenient data sharing tool. After configuring your LAN connection settings and Q-Share,
you are able to share your data with computers on the same network, making full use of Internet resources.

Directions for using Q-Share

After installing Q-Share from the motherboard driver disk, go to Start>All Programs>GIGABYTE>Q-Share.exe
to launch the Q-Share tool. Find the Q-Share icon in the notification area and right-click on this icon to
configure the data sharing settings.

Figure 1. Data Sharing Disabled Figure 2. Data Sharing Enabled

Options Descriptions
Option Description
Connect ... Displays the computers with data sharing enabled
Enable Incoming Folder ... Enables data sharing
Disable Incoming Folder ... Disables data sharing
Open Incoming Folder : Accesses the shared data folder
C:\Q-ShareFolder
Change Incoming Folder : Changes the data folder to be shared (Note)
C:\Q-ShareFolder
Update Q-Share ... Updates Q-Share online
About Q-Share ... Displays the current Q-Share version
Exit... Exits Q-Share

(Note) This option is available only when data sharing is NOT enabled.

Unique Features - 64 -
4-4 Smart Recovery 2
Smart Recovery 2 allows you to back up a partition as an image file every hour. You can use these images to
restore your system or files when needed.

The Smart Recovery 2 main menu:

Button Function
Settings Allows you to select the source and destination partition
Backup Now Allows you to perform the backup immediately
File Recovery... Allows you to recover your files from the backup image
System Allows you to recover your system from the backup
Recovery... image

•• Supported operating systems: Windows 7 and Vista.

•• Smart Recovery 2 only supports NTFS file system.
•• You need to select the destination partition in Settings the first time
you use Smart Recovery 2.
•• The Backup Now button will be available only after you log in
Windows for ten minutes.

Creating a backup:
Click the Settings button on the main menu. In the Settings dialog
box, select the source partition and destination partition and click OK.
The initial backup will start after 10 minutes and regular backup will be
performed hourly. Note: By default, all partitions on the system drive
are selected as the backup source. The backup destination cannot be
on the same partition as the backup source.

Saving the the backup to a network location:

If you want to save the backup to a network location, select Browse
network location. Make sure your computer and the computer where
you want to save the backup are in the same domain. Choose the
network location where you want to store the backup and enter the user
name and password. Follow the on-screen instructions to complete.

Recovering a file:
Click the File Recovery button on the main menu. Use the time slider on
the top of the popped out window to select a previous backup time. The
right pane will display the backed-up partitions in the backup destination
(in the My Backup folder). Browse to the file you want and copy it.

- 65 - Unique Features
 Recovering your system with Smart Recovery 2 (Windows 7 only):
Steps:
1. Click the System Recovery button on the main menu.
2. Select the location where your backup is saved.
3. Use the time slider to select a time point.
4. Select a partition backup created on the selected time point and
click Restore.
5. Confirm whether to restart your system to proceed with the restore
immediately or later. Once you respond "Yes" the system will restart to
the Windows recovery environment. Follow the onscreen instructions
to restore your system.
•• For Windows Vista, refer to the steps below to use the original
Windows installation disk for system recovery.
•• All of your files and programs will be deleted and replaced with those
on the selected backup. If needed, be sure to make a copy of your
data before the restore.

Recovering your system using the original Windows installation disk:

In case Windows or your hard drive has serious errors, use the original Windows installation disk for system recovery.
Steps:
1. Restart your computer to boot from the original Windows installation disk.
2. When the Windows installation screen appears, select your language and click Next.
3. Select Repair your computer.
4. Select Restore your computer using a system image that you created earlier and then click Next.
5. Select the backup you want to use and then follow the on-screen instructions to complete.
For further instructions, refer to the Help file of Smart Recovery 2.

Unique Features - 66 -
4-5 Auto Green
Auto Green is an easy-to-use tool that provides users with simple options to enable system power savings via
a Bluetooth cell phone. When the phone is out of the range of the computer's Bluetooth receiver, the system
will enter the specified power saving mode.
The Configuration dialog box:
First, you have to set your Bluetooth cell phone as a portable key. On the Auto Green main
menu, click Configure and then click Configure BT devices. Select the Bluetooth cell
phone that you want to use as the portable key (Note 1). (If the screen doesn't display your
Bluetooth cell phone, click Refresh to let Auto Green re-detect the device.)
Before creating a Bluetooth cell phone key, make sure your motherboard
has a Bluetooth receiver and you have turned on the search and Bluetooth
functions on your phone.
Configuring the Bluetooth cell phone key:
After you select a cell phone, the Add device as shown on the left will appear. Enter a
passkey (8~16 digits recommended) which will be used for pairing with the cell phone.
Then enter the same passkey on your cell phone.

Configuring other Bluetooth settings:

On the Other Settings tab, you can set how much time it takes to scan your Bluetooth
cell phone key, how many times to rescan the key to make sure it is in range of your
computer, and when to turn off the hard drive if the system energy saving state lasts
over the predetermined period of time. After completing the settings, click Set for the
settings to take effect and then click Exit to quit.

•• Device Scan Time (sec.):

Set the length of time Auto Green scans your Bluetooth cell phone key, ranging from 5 to 30 seconds in 5-second increment.
Auto Green searches for the key based on the length of time you set.
•• Rescan Times:
Set how many times Auto Green will rescan your Bluetooth cell phone key if it does not detect it, ranging from 2 to 5 times. Auto
Green will keep rescanning according to the times you set. When the times limit is reached and your Bluetooth cell phone key is
still not detected, the system will enter the selected energy saving mode.
•• Turn off HD:
Set when to turn off the hard drive. If the system inactivity time exceeds the specified time limit, the hard drive will be turned off.
Selecting a system energy saving mode:
Depending on your needs, select a system power saving mode on the Auto Green
main menu and click Save to save the settings.
Button Description
Standby Enters Power on Suspend mode
Suspend Enters Suspend to RAM mode
Disable Disables this function
The Bluetooth dongle included in the motherboard package(Note 2) allows
you to wake up the system from Suspend to RAM mode without the
need to press the power button first.

(Note 1) If your cell phone has been configured as the Auto Green key, you'll not be able to use it to connect to other Bluetooth
device(s) when Auto Green is enabled.
(Note 2) Whether the Bluetooth dongle is included depends on the motherboard models. Before installing the Bluetooth
dongle, be sure to turn off other Bluetooth receiver on your computer.

- 67 - Unique Features
Unique Features - 68 -
Chapter 5 Appendix
5-1 Configuring SATA Hard Drive(s)
RAID Levels
RAID 0 RAID 1 RAID 5 RAID 10
Minimum
Number of Hard ≥2 2 ≥3 ≥4
Drives
Array Capacity Number of hard Size of the smallest (Number of hard (Number of hard
drives * Size of the drive drives -1) * Size of drives/2) * Size of the
smallest drive the smallest drive smallest drive
Fault Tolerance No Yes Yes Yes

To configure SATA hard drive(s), follow the steps below:

A. Install SATA hard drive(s) in your computer.
B. Configure SATA controller mode in BIOS Setup.
C. Configure a RAID array in RAID BIOS. (Note 1)
D. Install the SATA RAID/AHCI driver (Note 2) and operating system.

Before you begin

Please prepare:
•• At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard
drives with identical model and capacity). If you do not want to create RAID, you may prepare only one
hard drive.
•• Windows 7/Vista/XP setup disk.
•• Motherboard driver disk.
•• A USB floppy disk drive (needed during Windows XP installation)
•• An empty formatted floppy disk (needed during Windows XP installation)

5-1-1 Configuring AMD SB950 SATA Controllers

A. Installing SATA hard drive(s) in your computer

Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available
SATA port on the motherboard. If there is more than one SATA controller on your motherboard, refer to
"Chapter 1," "Hardware Installation," to identify the SATA controller for the SATA port. (For example, on this
motherboard, the SATA3 0~SATA3 5 ports are supported by the AMD SB950 South Bridge.) Then connect
the power connector from your power supply to the hard drive.Then connect the power connector from your
power supply to the hard drive.

(Note 1) Skip this step if you do not want to create RAID array on the SATA controller.
(Note 2) Required when the SATA controller is set to AHCI or RAID mode.

- 69 - Appendix
B. Configuring SATA controller mode in BIOS Setup
Make sure to configure the SATA controller mode correctly in system BIOS Setup.

Step 1:
Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test).
Make sure OnChip SATA Controller is enabled. To enable RAID for the SATA3 0/1/2/3 connectors, set On-
Chip SATA Type to RAID. To enable RAID for the SATA3 4/5 connectors, set OnChip SATA Type to RAID
and set OnChip SATA Port4/5 Type to As SATA Type (Figure 1).

Figure 1

Step 2:
Save changes and exit BIOS Setup.

The BIOS Setup menus described in this section may differ from the exact settings for your moth-
erboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you
have and the BIOS version.

Appendix - 70 -
C. Configuring RAID set in RAID BIOS
Enter the RAID BIOS setup utility to configure a RAID array. Skip this step and proceed with the installation of
Windows operating system for a non-RAID configuration.

Step 1:
After the POST memory test begins and before the operating system boot begins, look for a message which
says "Press <Ctrl-F> to enter RAID Option ROM Utility" (Figure 2). Press <Ctrl> + <F> to enter the RAID
BIOS setup utility.
RAID Option ROM Version 3.3.1540.11
(c) 2011 Advanced Micro Devices, Inc. All rights reserved.

No Array is defined..

Press <Ctrl-F> to enter RAID Option ROM Utility...

Figure 2

Step 2:
Main Menu
This is the first option screen when you enter the BIOS RAID Setup utility. (Figure 3).
To view the disk drives assigned to arrays, press <1> to enter the View Drive Assignments window.
To create an array, press <2> to enter the LD View/LD Define Menu window.
To delete an array, press <3> to enter the Delete LD Menu window.
To view controller settings, press <4> to enter the Controller Configuration window.

Option ROM Utility (c) 2011 Advanced Micro Devices, Inc.

[ Main Menu ]

View Drive Assignments........................... [ 1 ]

LD View/ LD Define Menu...................... [ 2 ]

Delete LD Menu....................................... [ 3 ]

Controller Configuration............................ [ 4 ]

[ Keys Available ]

Press 1..4 to Select Option [ESC] Exit

Figure 3

- 71 - Appendix
Create Arrays Manually
To create a new array, press <2> to enter the LD View Menu window (Figure 4). To create an array, press
<Ctrl+C> to access the LD Define Menu.

Option ROM Utility (c) 2011 Advanced Micro Devices, Inc.

[ LD View Menu ]

< There is no any LD >

[ Keys Available ]
[h] Up [i] Down [PaUp/PaDn] Switch Page [Ctrl+C] Define LD
[Enter] View LD [Ctrl+V] View Single Disk [ESC] Exit

Figure 4

In the LD Define Menu, use the up or down arrow key to move to an item for further configuration (Figure 5).

Option ROM Utility (c) 2011 Advanced Micro Devices, Inc.

[ LD Define Menu ]
LD No LD Name RAID Mode Drv

LD 1 Logical Drive 1 RAID 0 0

Stripe Block 64 KB Initialization ON

Gigabyte Boundary ON
Read Policy Read Ahead Write Policy WriteBack
[ Drives Assignments ]

Port:ID Drive Model Capabilities Capacity (GB) Assignment

01:00 WDC WD800JD-22LSA0 SATA 3G 79.89 N
02:00 WDC WD800JD-22LSA0 SATA 3G 80.02 N

[[Keys
KeysAvailable
Available]]
[h] Up [i] Down [PaUp/PaDn] Switch Page [Space] Change Option
[Ctrl+Y] Save [ESC] Exit

Figure 5

Appendix - 72 -
In the following procedure, we'll create RAID 0 as an example.
1. Under the RAID Mode section, press the <SPACE> key to select RAID 0.
2. Set the Stripe Block size. 64 KB is the default.
3. Under the Drives Assignments section, press the up or down arrow key to highlight a drive.
4. Press the <SPACE> key or <Y>to change the Assignment option to Y. This action adds the drive to the
disk array. The Drv section will show the number of disks assigned.
5. Press <Ctrl>+<Y> keys to save the information. The message in Figure 6 will appear. Press <Ctrl+Y> to
input the array name. If you do not input the array name, the default array name will be used.
Please press Ctrl-Y key to input the LD name
or press any key to exit.
If you do not input any LD name, the default
LD name will be used.

Figure 6
6. When the next message appears, press <Ctrl>+<Y> to clear the MBR or press other keys to ignore this
option.
Fast Initialization option has been selected
It will erase the MBR data of the disks.
<Press Ctrl-Y key if you are sure to erase it>
<Press any other key to ignore this option>

Figure 7

7. Then, the message in Figure 8 will appear. Press <Ctrl>+<Y> to set the capacity of the RAID array or
press other keys to set the array to its maximum capacity.

Press Ctrl-Y to Modify Array Capacity or press any

other key to use maximum capacity...

Figure 8
8. After the creation is complete, the screen will return to LD View Menu where you will see the newly-
created array.
9. Press <Esc> to return to Main Menu and press <Esc> again if you want to exit the RAID BIOS utility.

- 73 - Appendix
View Drive Assignments
The View Drive Assignments option in the Main Menu displays whether the attached hard drives are as-
signed to a disk array or are unassigned. Under the Assignment column, drives are labeled with their as-
signed disk array or shown as Free if unassigned.

Option ROM Utility (c) 2011 Advanced Micro Devices, Inc.

[ View Drives Assignments ]

Port:ID Drive Model Capabilities Capacity (GB) Assignment

01:00 WDC WD800JD-22LSA0 SATA 3G 79.89
[S.M.A.R.T.] Health
Extent 1 79.82 LD 1-1
02:00 WDC WD800JD-22LSA0 SATA 3G 80.2
Extent 1 80.02 LD 1-2
[S.M.A.R.T.] Health

[ Keys Available ]
[h] Up [i] Down [PaUp/PaDn] Switch Page [Ctrl+H] Secure Erase
[ESC] Exit

Figure 9

Delete an Array
The Delete Array menu option allows for deletion of disk array assignments.

Deleting an existing disk array could result in loss of data. Record all array information including the
array type, the disk members, and stripe block size in case you wish to undo a deletion.
1. To delete an array, press <3> in the Main Menu to enter the Delete LD Menu. Then highlight the array you
wish to delete and press the <Delete> key or the <Alt>+<D> keys.
2. The View LD Defination Menu will appear (as shown in Figure 10) showing which drives are assigned to
this array. Press <Ctrl>+<Y> if you are sure to delete the array or other keys to abort.
3. When the array is deleted, the screen will return to Delete LD Menu. Press <Esc>to return to Main Menu.

Option ROM Utility (c) 2011 Advanced Micro Devices, Inc.

[ View LD Defination Menu ]

LD No LD Name RAID Mode Drv Capacity(GB)

LD 1 GBT RAID 0 2 80

Stripe Block 64 KB
Read Policy Read Ahead Write Policy WriteBack

[ Drives Assignments ]

Port:ID Drive Model Capabilities Capacity (GB)

01:00 WDC WD800JD-22LSA0 SATA 3G 79.89
02:00 WDC WD800JD-22LSA0 SATA 3G 80.02

Press Ctrl-Y to delete the data in the disk!

or press any other key to
[[Keys
Keys abort... ]]
Available
Available

Figure 10
Appendix - 74 -
5-1-2 Configuring Marvell 88SE9172 SATA Controller

A. Installing SATA hard drive(s) in your computer

Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available
SATA port on the motherboard. The Marvell 88SE9172 SATA controller controls the onboard eSATA connec-
tors on the back panel. Then connect the power connector from your power supply to the hard drive.

B. Configuring SATA controller and RAID mode in BIOS Setup

Make sure to configure the SATA controller mode correctly in system BIOS Setup.

Step 1:
Turn on your computer and press <Delete> to enter BIOS Setup during the POST. Go to Peripherals and set
Onboard eSATA Controller to Enabled. To create RAID, enter the Marvell ATA Controller Configuration
submenu and set GSATA Controller to RAID Mode (Figure 2). If you do not want to create RAID, set this
item to IDE Mode or AHCI Mode.

Figure 1

The BIOS Setup menus described in this section may differ from the exact settings for your moth-
erboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you
have and the BIOS version.

- 75 - Appendix
 Figure 2

Step 2:
Save changes and exit BIOS Setup.

C. Configuring a RAID array in RAID BIOS

Enter the RAID BIOS setup utility to configure a RAID array. Skip this step and proceed to the installation of
Windows operating system for a non-RAID configuration.
After the POST memory test begins and before the operating system boot begins, look for a message which
says "Press <Ctrl>+<M> to enter BIOS Setup or <Space> to continue" (Figure 3). Press <Ctrl> + <M> to en-
ter the RAID setup utility.
Marvell 88SE91xx Adapter - BIOS Version 1.0.0.0027
PCIe x1 5.0Gbps
Mode: RAID
[Virtual Disks]
No Virtual Disk!
[Physical Disks]
Adapter 0
Port Disk Name Size Max Speed
S0 SATA: WDC WD800JD-22LSA0 76.3GB SATA 3Gb/s
S1 SATA: WDC WD800JD-22LSA0 76.3GB SATA 3Gb/s

Press <Ctrl>+<M> to enter BIOS Setup or <Space> to continue_

Figure 3
Appendix - 76 -
On the main screen of the RAID setup utility (Figure 4), use the left or right arrow key to move through tabs.
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd.
[ Selection ] [ Adapter ] [ Devices ] [ RAID ]
Adapter 0

Vendor ID Device ID: 1B4B:91A2

BIOS Version: 1.0.1.0025
PCI Slot: 00
IRQ Number: 0A
Raid Mode: RAID0 RAID1

ENTER/SPACE: Select, ESC: Back/Exit

Figure 4

Create a RAID Array:

Step 1: On the main screen, press <Enter> on the RAID tab. Then the RAID Config menu appears (Figure 5).
Press <Enter> on the Create VD item.
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd.
[ Selection] [ Adapter] [ Devices] [ RAID ]

RAID Config
Create VD
Delete VD
Wipe out disk
Spare Management

ENTER/SPACE: Select, ESC: Back/Exit

Figure 5

- 77 - Appendix
Step 2: The next screen displays the two hard drives you installed. Press <Enter> or <Space> on the two
hard drives respectively to add them into the RAID array. Selected hard drives are marked with an asterisk
(Figure 6). Then press <Enter> on NEXT.
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd.
[ Selection] [ Adapter] [ Devices] [ RAID ]

RAID Config
Select free disks to create
Port Disk Name Size Max Speed Status
* S0 SATA: WDC WD800JD-22LSA0 76.3GB SATA 3Gb/s FREE
* S1 SATA: WDC WD800JD-22LSA0 76.3GB SATA 3Gb/s FREE
NEXT

ENTER/SPACE: Select, ESC: Back/Exit

Figure 6

Step 3: On the Create VD menu (Figure 7), use the up or down arrow key to move the selection bar to select
an item and press <Enter> to display options. Set the required items in sequence and press the down arrow
key to proceed to the next item.
Sequence:
1. RAID Level: Select a RAID level. Options include RAID 0 (Stripe) and RAID 1 (Mirror).
2. Stripe Size: Select the stripe block size. Options include 32 KB, 64 KB, and 128 KB.
3. Quick Init: Select whether to quickly erase old data on the hard drives when creating the array.
4. Cache Mode: Select write-back or write-through cache.
5. VD Name: Enter an array name with 1~10 letters (letters cannot be special characters).
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd.
[ Selection] [ Adapter] [ Devices] [ RAID ]

RAID Config
Select free disks to create
Port
Create VD Disk Name Size Max Speed Status
* S0 SATA: WDC WD800JD-22LSA0 76.3GB SATA 3Gb/s FREE
RAID Level : RAID0
* S1 Max SizeSATA:
(MB):WDC WD800JD-22LSA0
152478 76.3GB SATA 3Gb/s FREE
Stripe Size : 64KB
Quick Init : NO
Cache Mode : WriteBack
VD Name :
Disks ID : 01
NEXT

ENTER/SPACE: Select, ESC: Back/Exit

Figure 7

Appendix - 78 -
6. NEXT: After completing the settings above, move to NEXT and press <Enter> to begin creating the array.
When prompted to confirm, press <Y> to confirm or <N> to cancel (Figure 8).
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd.
[ Selection] [ Adapter] [ Devices] [ RAID ]

RAID Config
Select free disks to create
Port
Create VD Disk Name Size Max Speed Status
* S0 SATA: WDC WD800JD-22LSA0 76.3GB SATA 3Gb/s FREE
RAID Level : RAID0
* S1 Max SizeSATA:
(MB):WDC WD800JD-22LSA0
152478 76.3GB SATA 3Gb/s FREE
NEXT Stripe Size : 64KB
Quick Init : NO
Cache Mode : WriteBack
VD Name : GBT
Disk ID : 01
NEXT

Create the VD?[Y]

Figure 8

When completed, the RAID tab will display the new array. (Figure 9)
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd.
[ Selection ] [ Adapter ] [ Devices ] [ RAID ]

[Virtual Disks]
ID Name Size Level Status Stripe CacheMode
0 GBT 152.4GB RAID0 ONLINE 64KB WriteBack
[Physical Disks]
Port Disk Name Size Max Speed Status
S0 SATA: WDC WD800JD-22LSA0 76.3GB SATA 3Gb/s ASSIGNED
S1 SATA: WDC WD800JD-22LSA0 76.3GB SATA 3Gb/s ASSIGNED

ENTER/SPACE: Select, ESC: Back/Exit

Figure 9

To exit the RAID BIOS utility, press <Esc> on the main screen and press <Y> to confirm.
Now, you can proceed to install the operating system.

- 79 - Appendix
Delete the RAID Array:
To deleted the existing array, press <Enter> on the RAID tab and select Delete VD. When the Delete VD menu
appears, press <Enter> on the array to select it and then press <Enter> on NEXT. When prompted, press <Y>
to confirm (Figure 10). When the message "Do you want to delete the VD's MBR?" appears, press <Y> to
clear the MBR or press other keys to ignore.
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd.
[ Selection] [ Adapter] [ Devices] [ RAID ]

RAID Config
Delete VD
ID Name Size Level Status Stripe CacheMode
* 0 GBT 152.4GB RAID0 ONLINE 64KB WriteBack

NEXT

Delete the VD?[Y]

Figure 10

Use the Marvell Storage Utility in the Operating System:

With the Marvell Storage utility, you can set up an array or view the current array status in the operating
system. To install the utility, insert the motherboard driver disk, then go to Application Software\Install
Application Software and select Marvell Storage Utility to install. Note: After the installation, you must
login the utility with the same account name and password that you use to login the operating system.
If you did not set the account password before, click Login to enter the Marvell Storage Utility directly.
Please note that if you set the hard drive(s) to IDE or AHCI mode, it is normal that you will not see the hard
drive(s) in the Marvell Storage Utility.

Appendix - 80 -
5-1-3 Installing the SATA RAID/AHCI Driver and Operating System
With the correct BIOS settings, you are ready to install Windows 7/Vista/XP.

A. Installing Windows 7/Vista

(The following instructions use Windows 7 as the example operating system.)

For the AMD SB950:

Step 1:
You need to install the SATA RAID/AHCI driver during the OS installation. Use an alternative system to copy
the SATA RAID/AHCI driver from the motherboard driver disk to a USB flash drive. Copy the Hw7 folder un-
der BootDrv in the driver disk.

Step 2:
Boot from the Windows 7 setup disk and perform standard OS installation steps. When the screen requesting
you to load the driver appears, select Browse.

Step 3:
Then browse to the USB flash drive and select the location of the driver. The locations of the drivers are as
follows:
RAID driver for Windows 7 32-bit: Hw7\RAID\x86
RAID driver for Windows 7 64-bit: Hw7\RAID\x64
AHCI driver for Windows 7 32-bit: Hw7\AHCI\W7
AHCI driver for Windows 7 64-bit: Hw7\AHCI\W764A

Step 4:
When a screen as shown in Figure 1 appears, select AMD AHCI Compatible RAID Controller and click
Next to load the driver and continue the OS installation.

Figure 1

- 81 - Appendix
For the Marvell 88SE9172:
Step 1:
Copy the Marvell folder under BootDrv in the driver disk.

Step 2:
Boot from the Windows 7 setup disk and perform standard OS installation steps. When the screen requesting
you to load the driver appears, select Browse.

Step 3:
Insert the motherboard driver disk and then browse to the location of the driver. The locations of the drivers
are as follows:
RAID driver for Windows 32-bit: \BootDrv\Marvell\RAID\i386
RAID driver for Windows 64-bit: \BootDrv\Marvell\RAID\amd64
AHCI driver for Windows 32-bit: \BootDrv\Marvell\AHCI\Floppy32
AHCI driver for Windows 64-bit: \BootDrv\Marvell\AHCI\Floppy64

Step 4:
When a screen as shown in Figure 2 appears, select Marvell 91xx SATA 6G RAID Controller and click Next
to load the driver and continue the OS installation

Figure 2

Appendix - 82 -
B. Installing Windows XP
Before installing Windows XP, connect a USB floppy disk drive to your computer first because you need to in-
stall the SATA RAID/AHCI driver from a floppy disk that contains the driver during the OS installation. Without
the driver, the hard drive(s) may not be recognized during the Windows setup process. First, copy the driver
from the motherboard driver disk to a floppy disk. Refer to the methods below.

Method A:
•• For the AMD SB950 Chipset, copy all files in the \BootDrv\Hxp folder to your floppy disk.
•• For the Marvell 88SE9172, copy all files in the \BootDrv\Marvell\RAID\Floppy32 folder to your floppy
disk. For AHCI mode, depending on whether you want to install the 32- or 64-bit version, copy the files
in the AHCI\Floppy32 or AHCI\Floppy64 folder.

Method B:
Steps:
1. Use an alternative system and insert the motherboard driver disk.
2. From your optical drive folder, double click the Menu.exe file in the BootDrv folder. A Command Prompt
window will open similar to that in Figure 3.
3. Insert the blank formatted disk (if you're using a USB floppy disk drive, make sure it is designated as drive
A). Select the controller driver by pressing the corresponding letter from the menu and press <Enter>. For
example, from the menu in Figure 3:
•• For the AMD SB950 Chipset, select 6) hseries AHCI/RAID for XP
•• For the Marvell 88SE9172, select 5) Marvell RAID driver. (For AHCI drive(s), select Marvell AHCI
driver.)
Your system will then automatically copy the driver files to the floppy disk. Press any key to exit when finished.

Figure 3

- 83 - Appendix
Refer to the following for installing the driver during the Windows setup process.
For the AMD SB950:
Step 1:
Restart your system to boot from the Windows XP setup disk and press <F6> as soon as you see the mes-
sage "Press F6 if you need to install a 3rd party SCSI or RAID driver." A screen will then appear asking you to
specify an additional SCSI adapter. Press <S>.
Step 2:
Insert the floppy disk containing the SATA RAID/AHCI driver and press <Enter>. Then a controller menu simi-
lar to that in Figure 4 will appear. Select AMD AHCI Compatible RAID Controller-x86 platform and press
<Enter>.
Windows Setup

You have chosen to configure a SCSI Adapter for use with Windows,
using a device support disk provided by an adapter manufacturer.

Select the SCSI Adapter you want from the following list, or press ESC
to return to the previous screen.

AMD AHCI Compatible RAID Controller-x86 platform

AMD AHCI Compatible RAID Controller-x64 platform

ENTER=Select F3=Exit

Figure 4

Step 3:
On the next screen, press <Enter> to continue the driver installation. After the driver installation, you can pro-
ceed with the Windows XP installation.

Appendix - 84 -
For the Marvell 88SE9172:
Insert the floppy disk containing the SATA RAID/AHCI driver and press <Enter>. Both of the Marvell shared
library and Marvell 91xx SATA Controller need to be installed. Below we assume that you are installing
the 32-bit version. First select Marvell shared library (install first) and press <Enter>. On the next screen,
press <S> to return to the screen in Figure 5. Then select Marvell 91xx SATA Controller 32bit Driver and
press <Enter>. When both of the two drivers appear on the confirmation screen, press <Enter> to continue
the driver installation.
Windows Setup

You have chosen to configure a SCSI Adapter for use with Windows,
using a device support disk provided by an adapter manufacturer.

Select the SCSI Adapter you want from the following list, or press ESC
to return to the previous screen.

Marvell shared library (install first)

Marvell 91xx SATA Controller 32bit Driver

ENTER=Select F3=Exit

Figure 5

Step 3:
On the next screen, press <Enter> to continue the driver installation. After the driver installation, you can pro-
ceed with the Windows XP installation.

- 85 - Appendix
Rebuilding an Array:
Rebuilding is the process of restoring data to a hard drive from other drives in the array. Rebuilding applies
only to fault-tolerant arrays such as RAID 1, RAID 5, or RAID 10. To replace the old drive, make sure to use a
new drive of equal or greater capacity. The procedures below assume a new drive is added to replace a failed
drive to rebuild a RAID 1 array.

While in the operating system, make sure the chipset drivers have been installed from the motherboard driver
disk. Then launch the AMD RAIDXpert from All Programs in the Start Menu.

Step 1: Step 2:
Enter the login ID and password (default: "admin"), Select the RAID array to be rebuilt under Logical
and then click Sign in to launch AMD RAIDXpert. Drive View and click the Rebuild tab in the Logi-
cal Drive Information pane.

Step 3: Step 4:
Select one available drive and click Start Now to The rebuilding progress is displayed on the
start the rebuilding process. screen and you can select Pause/Resume/Abort
during the rebuilding process.

Step 5:
When done, the array's status on the Information page
in the Logical Drive Information pane will display as
Functional.

Appendix - 86 -
 For the Marvell 88SE9172:

Turn off your computer and replace the failed hard drive with a new one. Restart your computer. To enable an
automatic rebuild in the operating system, you have to set the new hard drive as a Spare drive in the RAID
setup utility first.

•• Enabling Automatic Rebuild

Step 1:
When the message "Press <Ctrl>+<M> to enter BIOS Setup or <Space> to continue" appears, press <Ctrl> +
<M> to enter the RAID setup utility. On the main screen, press <Enter> on the RAID tab and then press <En-
ter> on Spare Management.
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd.
[ Selection] [ Adapter] [ Devices] [ RAID ]

RAID Config
Create VD
Delete VD
Wipe out disk
Spare Management

ENTER/SPACE: Select, ESC: Back/Exit

Step 2:
The new hard drive will be displayed on the screen. Press <Enter> or <Space> on the new hard drive to select
it and then press <Enter> on NEXT. When prompted, press <Y> to confirm. The new hard drive is now set as a
Spare drive.
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd.
[ Selection] [ Adapter] [ Devices] [ RAID ]

RAID Config
Spare Management
Port Disk Name Size Max Speed Status
* S0 SATA: Seagate ST3120036AS 76.3GB SATA 3Gb/s FREE

NEXT

ENTER/SPACE: Select, ESC: Back/Exit

- 87 - Appendix
Step 3:
Make sure you have installed the Marvell RAID driver and Marvell Storage Utility from the motherboard driver
disk. While in the operating system, launch the Marvell Storage Utility from Start\All Programs\Marvell Storage
Utility\Marvell Tray.Then login the Marvell Storage Utility.

Under Virtual Disk 0, the Property tab displays the

rebuild progress on the right of the Background Activ-
ity Progress item, indicating that the RAID volume is
being rebuilt. When completed, the status will display
as Done.

•• Manually Rebuilding RAID 1 in the Operating System

You can manually rebuild a RAID 1 array without setting the new hard drive as a Spare drive in the RAID
setup utility first. While in the operating system, open the Marvell Storage Utility and login.

Step 1:
Under Virtual Disk 0, click the Operation tab and se-
lect Rebuild.

Step 2:
The screen will display the new hard drive. Click on the
hard drive to select it and click the Submit button to
begin the rebuild.

Appendix - 88 -
5-2 Configuring Audio Input and Output
5-2-1 Configuring 2/4/5.1/7.1-Channel Audio
The motherboard provides six audio jacks on the back
panel which support 2/4/5.1/7.1-channel (Note) audio.
The picture to the right shows the default audio jack Center/Subwoofer Line In
Speaker Out
assignments.
Rear Speaker Out Front Speaker Out
The integrated HD (High Definition) audio provides
Side Speaker Out Mic In
jack retasking capability that allows the user to change
the function for each jack through the audio driver.
For example, in a 4-channel audio configuration, if a Side speaker is plugged into the default Center/Sub-
woofer speaker out jack, you can retask the Center/Subwoofer speaker out jack to be Side speaker out.

•• To install a microphone, connect your microphone to the Mic in jack and manually configure the
jack for microphone functionality.
•• Audio signals will be present on both of the front and back panel audio connections simultane-
ously. If you want to mute the back panel audio (only supported when using an HD front panel
audio module), refer to instructions on the next page.

High Definition Audio (HD Audio)

HD Audio includes multiple high quality digital-to-analog converters (DACs) and features multistreaming ca-
pabilities that allow multiple audio streams (in and out) to be simultaneously processed. For example, users
can listen to MP3 music, have an Internet chat, make a telephone call over the Internet, and etc. all at the
same time.

A. Configuring Speakers
(The following instructions use Windows 7 as the example operating system.)

Step 1:
After installing the audio driver, the HD Audio Manager
icon will appear in the notification area. Double-click
the icon to access the HD Audio Manager.

(Note) 2/4/5.1/7.1-Channel Audio Configurations:

Refer to the following for multi-channel speaker configurations.
•• 2-channel audio: Headphone or Line out.
•• 4-channel audio: Front speaker out and Side speaker out.
•• 5.1-channel audio: Front speaker out, Side speaker out, and Center/Subwoofer speaker out.
•• 7.1-channel audio: Front speaker out, Rear speaker out, Center/Subwoofer speaker out, and Side speaker out.

- 89 - Appendix
Step 2:
Connect an audio device to an audio jack. The The cur-
rent connected device is dialog box appears. Select the
device according to the type of device you connect. Then
click OK.

Step 3:
On the Speakers screen, click the Speaker Configura-
tion tab. In the Speaker Configuration list, select Stereo,
Quadraphonic, 5.1 Speaker, or 7.1 Speaker according to
the type of speaker configuration you wish to set up. Then
the speaker setup is completed.

B. Configuring Sound Effect

You may configure an audio environment on the Sound Effects tab.

C. Activating an AC'97 Front Panel Audio Module

If your chassis provides an AC'97 front panel audio mod-
ule, to activate the AC'97 functionality, click the tool icon
on the Speaker Configuration tab. On the Connector
Settings dialog box, select the Disable front panel jack
detection check box. Click OK to complete.

D. Muting the Back Panel Audio (For HD Audio Only)

Click Device advanced settings on the top right corner
on the Speaker Configuration tab to open the Device
advanced settings dialog box. Select the Mute the rear
output device, when a front headphone plugged in
check box. Click OK to complete.

Appendix - 90 -
5-2-2 Configuring S/PDIF Out

The S/PDIF Out jack can transmit audio signals to an external decoder for decoding to get the best audio
quality.

1. Connecting a S/PDIF Out Cable:

Connect a S/PDIF optical cable to the corresponding S/PDIF out connector as shown below and an external
decoder for transmitting the S/PDIF digital audio signals.

Connects to a S/PDIF optical cable

2. Configuring S/PDIF Out:

On the Digital Output(Optical) screen (Note), click the Default Format tab and then select the sample rate and
bit depth. Click OK to complete.

(Note)  nter the Digital Output(Optical) screen to configure further settings if you use the S/PDIF Out
E
connector(s) on the back panel for digital audio output or enter the Digital Output screen if you use
the internal S/PDIF Out connector (SPDIF_O) for digital audio output.

- 91 - Appendix
5-2-3 Enabling the Dolby Home Theater Function

Before Dolby Home Theater is enabled, you get only 2-channel playback output (from the
front speakers) when playing 2-channel stereo sources. You must play 4-, 5.1-, or 7.1- chan-
nel content to get 4-, 5.1-, or 7.1- channel audio effects. With Dolby Home Theater enabled,
2-channel stereo content will be transformed into multi-channel audio, creating a virtual sur-
round sound environment.

Step 1:
The Dolby Home Theater icon will appear in the
notification area. Click the icon to access the Dolby
Home Theater.

Step 2:
Click the Customize button on the Dolby Home The-
ater panel to open advanced settings.

Appendix - 92 -
5-2-4 Configuring Microphone Recording
Step 1:
After installing the audio driver, the HD Audio Manager
icon will appear in the notification area. Double-click
the icon to access the HD Audio Manager.

Step 2:
Connect your microphone to the Mic in jack (pink) on
the back panel or the Mic in jack (pink) on the front
panel. Then configure the jack for microphone function-
ality.
Note: The microphone functions on the front panel and
back panel cannot be used at the same time.

Step 3:
Go to the Microphone screen. Do not mute the record-
ing volume, or you'll not be able to record the sound.
To hear the sound being recorded during the recording
process, do not mute the playback volume. It is recom-
mended that you set the volumes at a middle level.

Step 4:
To raise the recording and playback volume for the
microphone, click the Microphone Boost icon on
the right of the Recording Volume slider and set the
Microphone Boost level.

- 93 - Appendix
Step 5:
After completing the settings above, click Start, point
to All Programs, point to Accessories, and then click
Sound Recorder to begin the sound recording.

* Enabling Stereo Mix

If the HD Audio Manager does not display the recording device you wish to use, refer to the steps below. The
following steps explain how to enable Stereo Mix (which may be needed when you want to record sound from
your computer).

Step 1:
Locate the icon in the notification area and right-
click on this icon. Select Recording Devices.

Step 2:
On the Recording tab, right-click on an empty space
and select Show Disabled Devices.

Step 3:
When the Stereo Mix item appears, right-click on this
item and select Enable. Then set it as the default de-
vice.

Appendix - 94 -
Step 4:
Now you can access the HD Audio Manager to config-
ure Stereo Mix and use Sound Recorder to record the
sound.

5-2-5 Using the Sound Recorder

A. Recording Sound
1. Make sure you have connected the sound input device (e.g. microphone) to the computer.
2. To record the audio, click the Start Recording button .
3. To stop recording audio, click the Stop Recording button .
Be sure to save the recorded audio file upon completion.

B. Playing the Recorded Sound

You can play your recording in a digital media player program that supports your audio file format.

- 95 - Appendix
5-3 Troubleshooting

5-3-1 Frequently Asked Questions

To read more FAQs for your motherboard, please go to the Support & Downloads\FAQ page on GIGABYTE's
website.

Q: Why is the light of my keyboard/optical mouse still on after the computer shuts down?
A: Some motherboards provide a small amount of standby power after the computer shuts down and that's why the light is
still on.

Q: How do I clear the CMOS values?

A: For motherboards that have a Clear CMOS button, press this button to clear the CMOS values (before doing this, please
turn off the computer and unplug the power cord). For motherboards that have a Clear CMOS jumper, refer to the instruc-
tions in Chapter 1 to short the jumper to clear the CMOS values. If your board doesn't have this jumper/button, refer to the
instructions on the motherboard battery in Chapter 1. You can temporarily remove the battery from the battery holder to
stop supplying power to the CMOS, which will clear the CMOS values after about one minute.

Q: Why do I still get a weak sound even though I have turned my speaker to the maximum volume?
A: Make sure your speaker is equipped with an internal amplifier. If not, try a speaker with power/amplifier.

Q: Why cannot I install the onboard HD audio driver successfully? (For Windows XP only)
A: Step 1: First, make sure Service Pack 1 or Service Pack 2 has been installed (check in My Computer > Properties > Gen-
eral > System). If not, please update it from Microsoft's website. Then make sure the Microsoft UAA Bus Driver for
High Definition Audio has been installed successfully (check in My Computer > Properties > Hardware > Device
Manager > System Devices).
Step 2: Check if Audio Device on High Definition Audio Bus or Unknown device is present in Device Manager or
Sound, video, and game controllers. If yes, please disable this device. (If not, skip this step.)
Step 3: Then go back to My Computer > Properties > Hardware > Device Manager > System devices and right-click on
Microsoft UAA Bus Driver for High Definition Audio and select Disable and Uninstall.
Step 4: In Device Manager, right-click on the computer name and select Scan for hardware changes. When the Add
New Hardware Wizard appears, click Cancel. Then install the onboard HD audio driver from the motherboard
driver disk or download the audio driver from GIGABYTE's website to install.
For more details, go to the Support & Downloads\FAQ page on our website and search for "onboard HD audio driver."

Appendix - 96 -
5-3-2 Troubleshooting Procedure

If you encounter any troubles during system startup, follow the troubleshooting procedure below to solve the
problem.

START

Turn off the power. Remove all peripherals, connecting cables, and
power cord etc.

Make sure the motherboard does not short-circuit with the chassis or Yes
Isolate the short circuit.
other metal objects.

No The problem is verified and solved.

Secure the CPU cooler

Check if the CPU cooler is attached to the CPU securely. Is the pow- No on the CPU. Connect the
er connector of the CPU cooler connected to the CPU_FAN header CPU cooler power cable
properly? to the motherboard.

Yes The problem is verified and solved.

Correctly insert the

No
Check if the memory is installed properly on the memory slot. memory into the memory
socket.

Yes The problem is verified and solved.

Insert the graphics card. Connect the ATX main power cable and the
12V power cable. Turn on the power to start the computer.
Make sure the graphics card is securely seated in the
expansion slot and power connectors are firmly attached.

(Continued...)

- 97 - Appendix
 A

No The power supply, CPU or

When the computer is turned on, is the CPU cooler running? CPU socket might fail.

Yes The problem is verified and solved.

The graphics card,

No
Check if there is display on your monitor. expansion slot, or monitor
might fail.

Yes The problem is verified and solved.

Turn off the computer. Plug in the keyboard and mouse and restart
the computer.

No The keyboard or keyboard

Check if the keyboard is working properly.
connector might fail.

Yes The problem is verified and solved.

Press <Delete> to enter BIOS Setup. Select "Load Optimized De-

faults." Select "Save & Exit Setup" to save changes and exit BIOS
Setup.

The hard drive, connector,

Turn off the computer and connect the hard drive(s). Check if the No
or cable might fail.
system can boot successfully.

Yes The problem is verified and solved.

Reinstall the operating system. Reinstall other devices one by one

(install one device at one time and then boot the system to see if the
device works successfully).

END

If the procedure above is unable to solve your problem, contact the place of purchase or local deal-
er for help. Or go to the Support & Downloads\Technical Support page to submit your question.
Our customer service staff will reply you as soon as possible.

Appendix - 98 -
5-3-3 Regulatory Statements
Regulatory Notices
This document must not be copied without our written permission, and the contents there of must not be
imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted. We
believe that the information contained herein was accurate in all respects at the time of printing. GIGABYTE
cannot, however, assume any responsibility for errors or omissions in this text. Also note that the information
in this document is subject to change without notice and should not be construed as a commitment by
GIGABYTE.

Our Commitment to Preserving the Environment

In addition to high-efficiency performance, all GIGABYTE motherboards fulfill European Union regulations
for RoHS (Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment) and WEEE
(Waste Electrical and Electronic Equipment) environmental directives, as well as most major worldwide safety
requirements. To prevent releases of harmful substances into the environment and to maximize the use of
our natural resources, GIGABYTE provides the following information on how you can responsibly recycle or
reuse most of the materials in your "end of life" product.

Restriction of Hazardous Substances (RoHS) Directive Statement

GIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6,
PBDE and PBB). The parts and components have been carefully selected to meet RoHS requirement.
Moreover, we at GIGABYTE are continuing our efforts to develop products that do not use internationally
banned toxic chemicals.

Waste Electrical & Electronic Equipment (WEEE) Directive Statement

GIGABYTE will fulfill the national laws as interpreted from the 2002/96/EC WEEE (Waste Electrical and
Electronic Equipment) directive. The WEEE Directive specifies the treatment, collection, recycling and
disposal of electric and electronic devices and their components. Under the Directive, used equipment must
be marked, collected separately, and disposed of properly.

WEEE Symbol Statement

The symbol shown below is on the product or on its packaging, which indicates that this product
must not be disposed of with other waste. Instead, the device should be taken to the waste
collection centers for activation of the treatment, collection, recycling and disposal procedure.
The separate collection and recycling of your waste equipment at the time of disposal will help to
conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop off your waste equipment
for recycling, please contact your local government office, your household waste disposal service or where
you purchased the product for details of environmentally safe recycling.
ŠŠ When your electrical or electronic equipment is no longer useful to you, "take it back" to your local or
regional waste collection administration for recycling.
ŠŠ If you need further assistance in recycling, reusing in your "end of life" product, you may contact us at the
Customer Care number listed in your product's user's manual and we will be glad to help you with your
effort.

Finally, we suggest that you practice other environmentally friendly actions by understanding and using the
energy-saving features of this product (where applicable), recycling the inner and outer packaging (including
shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly.
With your help, we can reduce the amount of natural resources needed to produce electrical and electronic
equipment, minimize the use of landfills for the disposal of "end of life" products, and generally improve our
quality of life by ensuring that potentially hazardous substances are not released into the environment and
are disposed of properly.

- 99 - Appendix
Appendix - 100 -
- 101 - Appendix
Appendix - 102 -
 Contact Us

•• GIGA-BYTE TECHNOLOGY CO., LTD. •• NINGBO G.B.T. TECH. TRADING CO., LTD. - China
Address: No.6, Bao Chiang Road, Hsin-Tien Dist., WEB address : http://www.gigabyte.cn
New Taipei City 231,Taiwan Shanghai
TEL: +886-2-8912-4000 TEL: +86-21-63410999
FAX: +886-2-8912-4003 FAX: +86-21-63410100
Tech. and Non-Tech. Support (Sales/Marketing) : Beijing
http://ggts.gigabyte.com.tw TEL: +86-10-62102838
WEB address (English): http://www.gigabyte.com FAX: +86-10-62102848
WEB address (Chinese): http://www.gigabyte.tw Wuhan
•• G.B.T. INC. - U.S.A. TEL: +86-27-87851061
TEL: +1-626-854-9338 FAX: +86-27-87851330
FAX: +1-626-854-9326 GuangZhou
Tech. Support: http://ggts.gigabyte.com.tw TEL: +86-20-87540700
Warranty Info: http://rma.gigabyte.us FAX: +86-20-87544306
Web address: http://www.gigabyte.us Chengdu
•• G.B.T. INC (USA) - Mexico TEL: +86-28-85236930
Tel: +1-626-854-9338 x 215 (Soporte de habla hispano) FAX: +86-28-85256822
FAX: +1-626-854-9326 Xian
Correo: [email protected] TEL: +86-29-85531943
Tech. Support: http://rma.gigabyte.us FAX: +86-29-85510930
Web address: http://latam.giga-byte.com Shenyang
•• Giga-Byte SINGAPORE PTE. LTD. - Singapore TEL: +86-24-83992901
WEB address : http://www.gigabyte.sg FAX: +86-24-83992909
•• Thailand •• GIGABYTE TECHNOLOGY (INDIA) LIMITED - India
WEB address : http://th.giga-byte.com WEB address : http://www.gigabyte.in
•• Vietnam •• Saudi Arabia
WEB address : http://www.gigabyte.vn WEB address : http://www.gigabyte.com.sa
•• Gigabyte Technology Pty. Ltd. - Australia
WEB address : http://www.gigabyte.com.au

- 103 - Appendix
•• G.B.T. TECHNOLOGY TRADING GMBH - Germany •• Hungary
WEB address : http://www.gigabyte.de WEB address : http://www.giga-byte.hu
•• G.B.T. TECH. CO., LTD. - U.K. •• Turkey
WEB address : http://www.giga-byte.co.uk WEB address : http://www.gigabyte.com.tr
•• Giga-Byte Technology B.V. - The Netherlands •• Russia
WEB address : http://www.giga-byte.nl WEB address : http://www.gigabyte.ru
•• GIGABYTE TECHNOLOGY FRANCE - France •• Poland
WEB address : http://www.gigabyte.fr WEB address : http://www.gigabyte.pl
•• Sweden •• Ukraine
WEB address : http://www.gigabyte.se WEB address : http://www.gigabyte.ua
•• Italy •• Romania
WEB address : http://www.giga-byte.it WEB address : http://www.gigabyte.com.ro
•• Spain •• Serbia
WEB address : http://www.giga-byte.es WEB address : http://www.gigabyte.co.rs
•• Greece •• Kazakhstan
WEB address : http://www.gigabyte.com.gr WEB address : http://www.gigabyte.kz
•• Czech Republic You may go to the GIGABYTE website, select your language
WEB address : http://www.gigabyte.cz in the language list on the top right corner of the website.

• GIGABYTE Global Service System

To submit a technical or non-technical (Sales/Market-

ing) question, please link to:
http://ggts.gigabyte.com.tw
Then select your language to enter the system.

Appendix - 104 -