Size and Weight: 2.875'' 10.40 ppf 0.

362'' wall IU
Grade: G-105
Drill Pipe Performance Sheet Range: 2
Asset Number: 18929 Tool Joint: 3.125'' x 1.500'' 2 7/8" HTPAC

Pipe Body: Tubular Assembly:

Nominal Ultra Class Premium
100% RBW 95% RBW 90% RBW 80% RBW Adjusted Weight (lbs/ft): 10.98 Fluid Displacement (gal/ft): 0.17
Approximate Length (ft): 31.5 Fluid Displacement (bbls/ft): 0.0040
OD (in): 2.875 2.839 2.803 2.730
Wall Thickness (in): 0.362 0.344 0.326 0.290 Box TJ Length (in): 13 Fluid Capacity w/IPC (gal/ft): 0.17
Nominal ID (in): 2.151 2.151 2.151 2.151 Pin TJ Length (in): 9 Fluid Capacity w/IPC (bbls/ft): 0.0041

Tensile Strength (lbs): 300,082 283,025 266,183 233,149 Upset Type: IU Fluid Capacity w/o IPC (gal/ft): 0.18
Torsional Strength (ft-lbs): 16,176 15,203 14,250 12,401 Max Upset OD (in): 3.000 Fluid Capacity w/o IPC (bbls/ft): 0.0042
Drift Size (in): 1.375
Burst Capacity (psi): 23,137 25,120 23,798 21,153
Collapse Capacity (psi): 23,112 22,358 21,574 19,912

Note: These are OEM values that may vary with actual values due to mill tolerances, IPC tolerances, OEM rounding, and other
Notes: Body properties are calculated based on uniform OD and wall thickness. factors. Pipe is purchased at a guaranteed 95% RBW. IPC is applied to a nominal thickness of 0.009''. Pipe will have an ID of
Burst capacity for Nominal (100% RBW) based on 87.5% RBW per API. 2.093'', which is smaller than pipe purchased at 87.5%.

Connection: 2 7/8" HTPAC 1.0 FF 1.1 FF 1.15 FF Elevator Shoulder:

TJ OD (in): 3.125
TJ ID (in):1.500 18
MYS (ksi): 120 Maximum MUT (ft-lbs): 5,100 5,610 5,865 Smooth Edge Height (in): N/A
Maximum MUT is recommended
based on thread compound Tension at Shoulder Separation @ Max MUT (lbs): Tensile Limited Tensile Limited Tensile Limited Smooth Edge OD (in): N/A
friction factor (unless stated). Tension at Connection Yield @ Max MUT (lbs): 213,300 213,300 213,300 SE Elevator Shoulder Capacity (lbs): N/A
Lower than maximum MUT
should only be used when MUT
is limited by rig equipment or Minimum MUT (ft-lbs): 4,300 4,730 4,945 Nominal TJ OD (in): 3.125
connection tensile. Lower than Tension at Shoulder Separation @ Min MUT (lbs): Tensile Limited Tensile Limited Tensile Limited
minimum MUT should never be
used. Tension at Connection Yield @ Min MUT (lbs): 263,200 263,200 263,200

N/A Tool Joint Torsional Strength (ft-lbs): 8,500 9,350 9,775

N/A Tool Joint Tensile Strength (lbs): 266,300 266,300 266,300
2 7/8" HTPAC is a trademark of NOV Grant Prideco. This asset must be handled with a lift nubbin. For more information, please consult
Note: There is no published pressure rating for this connection. Workstrings Operations.
*ADJUST makeup torque according to thread compound friction factor (FF) greater than 1.0 up to 1.15 FF. Not to exceed 1.15 regardless of dope FF.* Reference Page 3

The technical information contained herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical
information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various
inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices,
and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.

www.workstringsinternational.com 02-Jun-20
Download the Workstrings International Pipe Specification App on the App Store℠ or Google Play™
 Operational Limits of Drill Pipe
Connection HT 2-7/8 PAC Tool Joint OD (in) 3.125 Tool Joint ID (in) 1.500 Tool Joint Specified Minimum 120,000
Yield Strength (psi)

Pipe Body 80 % Inspection Class Pipe Body OD (in) 2.875 Wall Thickness (in) 0.362 Pipe Body Grade G-105

(ft-lbs) (ft-lbs)

(ft-lbs) (lbs) (lbs) (lbs) (ft-lbs) (lbs) (lbs) (lbs)

0 213,300 233,100 213,300 0 233,100 233,100 263,200

233,100 213,300 200 233,100 233,100 263,200

200 213,300
233,000 213,300 400 233,000 233,000 263,200
400 213,300
700 213,300 232,800 213,300 500 233,000 233,000 263,200

900 213,300 232,500 213,300 700 232,800 232,800 263,200

1,100 213,300 232,200 213,300 900 232,500 232,500 263,200

1,300 213,300 231,900 213,300 1,100 232,200 232,200 263,200

1,600 213,300 231,200 213,300 1,300 231,900 231,900 263,200

1,800 213,300 230,700 213,300 1,400 231,700 231,700 263,200

2,000 213,300 230,100 213,300 1,600 231,200 231,200 263,200

229,500 213,300 1,800 230,700 230,700 263,200

2,200 213,300
228,400 213,300 2,000 230,100 230,100 263,200
2,500 213,300
2,700 213,300 227,600 213,300 2,200 229,500 229,500 263,200

2,900 213,300 226,700 213,300 2,300 229,100 229,100 263,200

3,100 213,300 225,700 213,300 2,500 228,400 228,400 263,200

3,400 213,300 224,200 213,300 2,700 227,600 227,600 263,200

3,600 213,300 223,100 213,300 2,900 226,700 226,700 263,200

3,800 213,300 221,900 213,300 3,100 225,700 225,700 263,200

4,000 213,300 220,700 213,300 3,200 225,300 225,300 263,200

219,000 213,300 3,400 224,200 224,200 263,200

4,300 213,300

Connection
Make-up Torque Range

(ft-lbs) (lbs)

4,300 263,200
4,400 257,600
4,500 251,900
4,600 246,300
4,700 240,700
4,700 235,700
4,800 230,100
4,900 224,500
5,000 218,900
5,100 213,300
Note: Recommended MUT should always be used when possible. If not possible, MUT should be as close to Recommended MUT as possible.

Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box ID’s, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.

06-17-2015
 Makeup Torque Guidelines
- Good COPPER-BASED thread compound is recommended for rotary-shouldered drill pipe connections by the OEM.
- Be LIBERAL with the thread compound in the box, the base of the box, and on the pin using a copper-based or a
compatible thread compound.
- Ensure 360 DEGREES of coverage of the threads and torque shoulders.
- Ensure 360 DEGREES of coverage on the seal surfaces on completion pipe.
- Always ENSURE proper pipe alignment.
- ADJUST makeup torque according to thread compound Friction Factor (FF) greater than 1.0 FF up to 1.15 FF.
Workstrings Engineering is available for more information.
- MINIMIZE clamp pressure with the tongs or iron roughneck.
- MAXIMIZE the distance between the box shoulder and lower jaw die per OEM guidelines (1”-2” minimum for most
tool joints).
- Use a SLOW rotation speed during spin-up and break-out of the first 5-6 threads - especially critical for premium
and completion connections.

NOTE: More detailed running procedures for proprietary rotary-shouldered connections are available from the OEM’s website

PIPE SPECIFICATION MOBILE APP

Download the Workstrings International Pipe Specification App on the App StoreSM or
Google PlayTM
The App allows users to access specifications for the most commonly used sizes and
connections of drill pipe, landing string, HWDP, drill collars and tubing providing the
option to view and email specification sheets conveniently using your mobile device.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of
Apple Inc. Google Play is a trademark of Google Inc.

Global Headquarters Engineering & Marketing EMEA Corporate

1150 Smede Hwy 11330 Clay Road, Suite 200 Kirkton Avenue, Dyce
Broussard, LA 70518 - USA Houston, TX 77041 - USA Aberdeen, AB21 0BF - UK
Phone: +1 337-989-9675 Phone: +1 281-999-0047 Phone: +44 1224-724900
Email: [email protected] Email: [email protected] Email: [email protected]

www.workstringsinternational.com