TVL-IA (Electrical Installation and

Learning Area Grade Level

W1
12
Maintenance)
Quarter Fourth Date
I. LESSON TITLE PERFORM ROUGHING-IN ACTIVITIES FOR COMMUNICATION AND DISTRIBUTION
SYSTEM USING ELECTRICAL METALLIC CONDUIT
II. MOST ESSENTIAL LEARNING
LO 1. Install electrical metallic tubing
COMPETENCIES (MELCs)
III. CONTENT/CORE CONTENT ● Install electrical metallic tubing according to the job requirements
following PEC and NEC
● PEC provisions on electrical metallic conduits

IV. LEARNING PHASES AND LEARNING ACTIVITIES

I. Introduction (Time Frame: ________)
PEC PROVISION ON ELECTRICAL METALLIC TUBING

A rigid metal conduit is a type of wiring installation which is designed to lessen or eliminate fire hazard and electrical
accident. The following rules and regulations on the use of electrical metallic tubing should be observed:

Electrical metallic tubing may be used for exposed and concealed work at the same condition with rigid metal conduit.
EMT protected with enamel should not be used on the following conditions:

a. subjected to mechanical during or after the construction

b. cinder fill
c. hazardous location
d. exposure to corrosive fumes and vapor
Electrical metallic tubing has smooth surface inside diameter. Its standard length follows the gas pipe which is 10 ft. and a
diameter from ½ inch, ¾ inch up to 6 inches.
Electrical metallic tubing can be used provided the water is prevented in entering the conduit. The support, straps and
other fitting must be approved for the purpose.

Learning Task 1
Arrange the following jumbled words into a meaningful word. Write your answers on your answer sheet or work sheet
notebook.
1. ONDUTIC – ________________________
2. SOODRAZAH – ________________________
3. NECCORNTORN – ________________________
4. BOWEL – ________________________
5. LICALTEM BITUNG – ________________________
6. TESOFF – ________________________
7. DELDAS – ________________________
8. ODEC – ________________________
9. NGITTIF – ________________________
10. CKOLTUN – ________________________

For ODL and Blended Modality:

You can access additional information using the link below.
https://filipinoengineer.com/wiki/PEC
The proper usage of electrical materials, tools and PPE must be observed in installing the EMT. The sizes should be
considered as well as the quality of materials which should be in accordance with the PEC and NEC.
Learning Task 2
Identify each picture of materials, tools and PPE in column A with the name listed in column B. Write the letter of the
correct answer. Write your answers on your answer sheet or work sheet notebook.

A B
 1. A. Hacksaw

2. B. Pull-push rule

3. C. Straps

4. D. Condulets

5. E. Gloves

6. F. Locknut

7. G. Adapter

8. H. Coupling

9. I. Connector

10. J. Octagonal box

For ODL and Blended Modality:

You can access additional information using the link below.
https://iiee.org.ph:89/uploads/files/1176.pdf

There are three basic bends that are commonly used: the 90° bend, the common offset and the saddle. Each bending
style has proper procedure to follow. There must be an accurate measuring to achieve a good metal bending.
For connecting metal raceways, we intend to use appropriate fittings to make the harness of each tubing fitly joint.
In installation of metal raceway the size of the metallic tubing has each proper size of wire that will be inserted inside the
tubing.
Learning Task 3
A. Identify the following statement. Write your answers on your answer sheet or work sheet notebook.

________________________1. It is a kind of bend to cross a small destruction that would prevent the electrician.
 ________________________2. Bends are used to move a run of conduit from one plane to another.
________________________3. Bends are classified as 90 degrees or 45 degrees.
________________________4. A thin-walled metal raceway having a circular cross section.
________________________5. Also known as electrical fittings, used to connect runs conduit together.
B. Determine the missing data in the table.
Trade size of conduit in Size in AWG No. of
inches conductors
1. 3/8“ 8
2. 14 8
3. 3/4" 10
4. 1” 12
5. 1 ½” 12
For ODL and Blended Modality:
You can access additional information using the link below.
dengarden.com/home-improvement/EMT-Electrical-Conduit-Pipe-Bending-Instructions
One of the problems that both commercial and industrial fields face today is that few electricians don't know how to
bend EMT conduit with a hand bender. This is one of the primary skills necessary to acquire but for new electricians this is the
most troubling stage. Learning how to bend conduit is an early task for the beginning electrician in both the commercial and
industrial fields.
Proper procedure must take place when doing the bending of EMT. This may help certain electricians to do their job
properly and to avoid hazards. The following picture may help to understand the step-by-step procedure.

Learning Task 4
Arrange the proper procedure on elbow bending of metallic tubing from 1-9. Write your answers on your answer sheet
or work sheet notebook.
_________________A. Mark of the center of the location of the bend.
_________________B. Remove the bender on the right angle bent EMT.
_________________C. Draw a right angle bend on the floor using the try square.
_________________D. Insert the EMT into the conduit bender/hickey where the center of the bend is to be made.
_________________E. Prepare the necessary tools, materials and equipment.
_________________F. Bend the EMT gradually to form a 90 bend. Check the desired shape by placing the conduit on the
layout.
_________________G. Draw an arc near the corner.
_________________H. Observe good housekeeping.
_________________I. Wear the appropriate PPE

For ODL and Blended Modality:

You can access additional information using the link below.

dengarden.com/home-improvement/EMT-Electrical-Conduit-Pipe-Bending-Instructions
V. ASSESSMENT (Time Frame: _________)
(Learning Activity Sheets for Enrichment, Remediation, or Assessment to be given on Weeks 3 and 6)
Make a 1-10 step by step of proper procedure of bending metallic tubing for offset bend. Write your answers on your
answer sheet or work sheet notebook.
1. ___________________________________________________________________
2. ___________________________________________________________________
3. ___________________________________________________________________
4. ___________________________________________________________________
5. ___________________________________________________________________
6. ___________________________________________________________________
7. ___________________________________________________________________
8. ___________________________________________________________________
9. ___________________________________________________________________
10. ___________________________________________________________________
For ODL and Blended Modality:
You can access additional information using the link below.
dengarden.com/home-improvement/EMT-Electrical-Conduit-Pipe-Bending-Instructions
VI. REFLECTION (Time Frame: _________)
● Communicate your personal assessment as indicated in the Learner’s Assessment Card.
Personal Assessment on Learner’s Level of Performance
Using the symbols below, choose one which best describes your experience in working on each given task. Draw it
in the column for Level of Performance (LP). Be guided by the descriptions below:
 - I was able to do/perform the task without any difficulty. The task helped me in understanding the target content/
lesson.
- I was able to do/perform the task. It was quite challenging, but it still helped me in understanding the target
content/lesson.
? – I was not able to do/perform the task. It was extremely difficult. I need additional enrichment activities to be able to
do/perform this task.
Learning Task LP Learning Task LP Learning Task LP Learning Task LP
Number 1 Number 3 Number 5 Number 7
Number 2 Number 4 Number 6 Number 8
VII. REFERENCES Rodrigo S. Castillo et al.,DEPED – COMPETENCY-BASED LEARNING MATERIALS
ELECTRICAL INSTALLATION NC II PERFORMING ROUGHING-IN ACTIVITIES FOR COMMUNICATION
AND DISTRIBUTION SYSTEM

Hector M. Vallarta And Roman A. Cabusora Jr,ELECTRICAL INSTALLATION MAINTENANCE

EXPLORATORY COURSE GRADE 7 AND 8 K to 12 – Technology and Livelihood Education
Prepared by: Dennis D. Librando Checked by: Christian M. Niebres
Diosdado S. Villeta