installation manual

Activa+ op. single

DTMJOVL101EN - v1 - ENGLISH ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S1

Activa+ single slide operator

Installation Step#1
Packaging
1- BOX #1: DRIVE UNIT & ACCESSORIES

i
Inside this box you will find all the necessary
elements to assemble the drive unit and the
main accessories to operate and control the
door.
sa
fragil
manu
O
PT

These elements are optional, and will

fragil
be found inside this box as per the configuration
of the automatic door.

Box #1

* Only one reference will be delivered

Ref. Description Location
Ref. Description Location Ref. Description Location * BRCVLT Activa+ SS dragging arm Box #1
GV Activa+ motor group Box #1 CACV04 Activa+ leaf trolleys Box #1 * KEGV15LT Activa+ SS extension kit Box #1
O

O
PT

PT

Ref. Description Location Ref. Description Location

CJGV03 Activa+ automatic lock Box #1 APGV04 CO-48 mechanical fail-safe Box #1

01 M s1
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S1

O
PT

PT

PT
sa
nu
ma

Ref. Description Location Ref. Description Location Ref. Description Location

EDFM01 Manusa photocell. Complete Box #1 EDFE01 Photocell housing Box #1 EDDP01 Touch-less switch Box #1
O

O
PT

PT

PT
Ref. Description Location Ref. Description Location Ref. Description Location
EDRM05 Manusa planar radar Box# 1 EDRM04 Manusa infrared sensor IR-2 Box #1 EMPA01 Opening push button Box #1
O

O
O

PT

PT
PT

sa
nu
ma

Ref. Description Location Ref. Description Location Ref. Description Location

EMSR03 Key operated rotative selector Box #1 EMSM03 Optima selector Box #1 EMMD04 Remote control for Optima sel. Box #1
O

O
PT

PT

PT

....
Ref. Description Location Ref. Description Location Ref. Description Location
EMLL01 Key switch Box #1 EDAA01 Buzzer Box #1 ------------ Other optional elements Box #1

02 M s1
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S1

2- Box #2: HEADER FRAME

i
Inside this box you will find the aluminium profiles
and all necessary accessories to build the
header frame.
O
PT

These elements are optional, and will be

found inside this box as per the configuration
of the automatic door.

Box #2

CVPC29
Activa+ header frame: main
profile

Ref. Description Location Ref. Description Location

PACVPC29 Activa+ main profile Box #2 CSPR Track rail Box #2

O
PT

Ref. Description Location Ref. Description Location Ref. Description Location

KSCVPC01 Activa+ front suspension pack Box #2 KSCVPC03 Activa+ pack of accessories Box #2 PACVPLP2 Activa+ clear width profile Box #2
O
O

PT
PT

Ref. Description Location Ref. Description Location

JF06 Wool pile seal 7x8 E20 Box #2 KSCVPC02 Activa+ iron caps pack Box #2

03 M s1
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S1

CVCC29

O
PT
Activa+ header frame:
cover

Ref. Description Location Ref. Description Location

KSCVCC02 Activa+ plastic end caps Box #2 PACVCI29 Bottom cover Box #2

Ref. Description Location Ref. Description Location Ref. Description Location

PACVCFPS29 Front cover Box #2 JUCI Rubber hinge for bottom cover Box #2 KSCVCC01 Activa+ cover suspension pack Box #2

04 M s1
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S1

3- Box #3: STRUCTURAL ELEMENTS

i
Inside this box you will find the aluminium profiles
and all necessary accessories used to fix and
secure the header frame, when required.
O
PT

These elements are optional, and will be

found inside this box as per the configuration
of the automatic door.

Box #3

CSPD
O
PT

Manusa goal posts

Ref. Description Location Ref. Description Location

PAPD01 Goal post strut Box #3 PAPD02 Goal post cover Box #3

Ref. Description Location

KCSPD1 Pack of access. for goal post Box #3

05 M s1
DTMJOVL101EN - v1 - ENGLISH ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S2

Activa+ single slide operator

Installation Step #2
Main profile assembly

1- WHERE TO FIND THE NECESSARY ELEMENTS

O
PT
Ref. Description Location

Description Location PACVPLP2 Activa+ clear width profile Box #2

Ref. Ref. Description Location
PACVPC29 Activa+ main profile Box #2 CSPR Track rail Box #2 JF06 Wool pile seal 7x8 E20 Box #2

Ref. Description Location Ref. Description Location Ref. Description Location

GV Activa+ motor group Box #1 KSCVPC03 Activa+ pack of accessories Box #2 KSCVCC01 Activa+ cover suspension pack Box #2
O
PT

Ref. Description Location

CJGV03 Activa+ automatic lock Box #1

01 M s2
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S2

2- PREPARATION OF THE ALUMINIUM PROFILES

i
IMPORTANT: All aluminium profiles (main profile, track rail and clear width profile) Tools
must be cut down to size, as per the cutting dimensions shown on point no. 6
of Step S2 in this manual.

Saw

1.- Front fixing only: Drill 5 holes as shown on Pic 2.1 / 2.2
Tools
IMPORTANT: Drill only on the indicated area of the main profile Pic 2.1
Clean and remove all rests of aluminium chips after drilling the holes, preferibly
using an air compressor gun. 25
drill diam 10

Pic 2.1
a

Pic 2.2

.5
R5
20

25

32

Pic 2.3

i
1.- Cut the clear width profile as shown on Pic 2.3 Tools
Profile length = Clear width + 100 mm

Saw
0
+5
CW

02 M s2
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S2

3- FIX THE ALUMINIUM TRACK RAIL

i Pic 2.4
1.- Detach the double side tape Pic 2.4

2.- Stick the track rail to the main profile Pic 2.5

IMPORTANT: Stick firmly and avoid air gaps. To stick properly, start fixing
one end of the track rail on point A (at 15 mm from the edge), and continue
fixing slowly in the opposite direction (towards B) until you reach the other
end..

mm
15
Pic 2.5

4- SLIDE THE NUTS AND HANDRAILS

i Pic 2.6
1.- Slide the rail nuts as shown on Pic 2.6.

2.- On Pic 2.7/2.8 you will see the right number of rail nuts and square
nuts to slide on the main profile, and its correspondance with all the
elements.

03 M s2
 LIST OF RAIL NUTS TO SLIDE ON THE MAIN PROFILE (SINGLE SLIDE WITH LEFT SIDE OPENING ONLY) ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S2

i
List of elements and accessories to be fixed on the main profile:
1- Motor group
2- Cover suspension brackets
3- Fixed leaf suspension brackets
4- Clear width profile
5- Central steel stopper (default) or Activa+ automatic lock(optional)

5
4

2
04 M
s2

2
Pic 2.7
manusa

2
 LIST OF RAIL NUTS TO SLIDE ON THE MAIN PROFILE (SINGLE SLIDE WITH RIGHT SIDE OPENING ONLY) ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S2

i
List of elements and accessories to be fixed on the main profile:
1- Motor group
2- Cover suspension brackets
3- Fixed leaf suspension brackets
4- Clear width profile
5- Central steel stopper (default) or Activa+ automatic lock(optional)

3
2
05 M

3
s2

Pic 2.8
asunam

5
2
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S2

5- FIX THE CLEAR WIDTH PROFILE

i
1.- Fix the clear width profile to the main profile as shown on Pic 2.9 / 2.10

2.- Once the clear width profile has been fixed in place, slide the woolpile seal as shown on Pic 2.11

0
+5
CW
Pic 2.9
manusa

Pic 2.10
a

Pic 2.10 Pic 2.11

Pic 2.10 Pic 2.11

06 M s2
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S2

6- CUTTING DIMENSIONS

i MAXIMUM LENGTH = 2900

( CW X 2 ) + 50
In the following chart we display the minimum cutting dimensions of all the manusa

aluminium profiles and other elements for an Activa+ single slide operator.

All dimensions depend on the clear opening width (CW).

The maximum dimensions displayed correspond to the maximum

recommended dimension for a single sliding door.
CW

PART NO. DESCRIPTION MAX. LENGTH MINIMUM LENGTH

PACVPC41 ACTIVA+ MAIN PROFILE 2900 L1 = ( CW x 2 ) + 50

CSPR TRACK RAIL 2900 L2 = ( CW x 2 ) + 20

PACVPLP2 ACTIVA+ CLEAR WIDTH PROFILE 2900 L3 = CW + 50

JF06 WOOL PILE SEAL 7x8 E20 ------- L4 = CW + 50

PACVCFPS ACTIVA+ FRONT COVER 2900 L5 = ( CW x 2 ) + 40

PACVCIPS ACTIVA+ BOTTOM COVER 2900 L6 = ( CW x 2 ) + 40

JUCI RUBBER HINGE ------- L7 = ( CW X 2 ) + 40

07 M s2
DTMJOVL101EN - v1 - ENGLISH ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S3

Activa+ single slide operator

Installation Step #3
Leaf trolleys assembly and installation
1- WHERE TO FIND THE NECESSARY ELEMENTS

Ref. Description Location Ref. Description Location

CACV04 Activa+ leaf trolleys Box #1 KSCVPC03 Activa+ pack of accessories Box #2

* Only one reference will be delivered

Ref. Description Location
Ref. Description Location * BRCVLT Activa+ SS dragging arm Box #1
GV Activa+ motor group Box #1 * KEGV15LT Activa+ SS extension kit Box #1

terms
Rigth side opening: Left side opening:
trolley A trolley B trolley B trolley A

01 M s3
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S3

2- LEAF TROLLEYS ASSEMBLY

i Pic 3.1
Tools
On all both trolleys (A and B):
1.- Assemble the leaf suspension brackets as
shown on Pic 3.1 / Pic 3.2 / Pic 3.3
nº10-11/nº12-13
2.- Put on the screws and nuts, but do not tighten
fully yet. Attach the central bolt as shown on Pic 3.2 / Pic 3.3

Pic 3.2 Pic 3.3

i
Tools
On the trolley A:
1.- Fix the screws, dragging arm and nuts as shown on Pic 3.4 / Pic 3.5
/ Pic 3.6 / Pic 3.7
2.- Assemble as shown on Pic 3.4 / Pic 3.6 if the door opens to the right
nº10-11
3.- Assemble as shown on Pic 3.5 / Pic 3.7 if the door opens to the left

Pic 3.4 Pic 3.5

Pic 3.6 Pic 3.7

02 M s3
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S3

3- FIX THE TROLLEYS TO THE MAIN PROFILE

3a- OPERATOR WITH RIGHT SIDE OPENING

manusa

i
Tools
1.- Fix the trolleys on the track rail Pic 3.8 / 3.9
2.- Slide the middle wheel to the top until the trolley is well
adjusted to the main profile. Pic 3.9
3.- Tighten the middle wheel firmly and check that trolleys slide nº4
smoothly and securely (without bouncing) on the track rail .
Pic 3.8 / 3.10
4.- Insert the rubber stops on one end of the trolley B as shown on
Pic 3.8 / 3.9
5.- Insert the steel stopper on the opposite end of the trolley A as shown on
Pic 3.8 / 3.10

Pic 3.8

Pic 3.10

Pic 3.9

Pic 3.9 Pic 3.9

Pic 3.9 Pic 3.10

03 M s3
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S3

3b- OPERATOR WITH LEFT SIDE OPENING

manusa

i
Tools
1.- Fix the trolleys on the track rail Pic 3.11 / 3.12
2.- Slide the middle wheel to the top until the trolleys are well
adjusted to the main profile. Pic 3.12
3.- Tighten the middle wheel firmly and check that trolleys slide nº4
smoothly and securely (without bouncing) on the track rail .
Pic 3.11 / 3.13
4.- Insert the rubber stops on one end of the trolley B as shown on
Pic 3.11 / 3.12
5.- Insert the steel stopper on the opposite end of the trolley A as shown on
Pic 3.11 / 3.13

Pic 3.11

Pic 3.12

Pic 3.13

Pic 3.12 Pic 3.12

Pic 3.12 Pic 3.13

04 M s3
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S3

4- ASSEMBLE THE END STOPS

4a- OPERATOR WITH RIGHT SIDE OPENING

manusa

i
1.- Fix the central steel stopper to the rail nut supplied, ant Tools
secure it at 100 mm from the left end of the main pofile. Pic
3.14 / 3.15

2.- Fix the side stopper on the right end of the track rail as nº10
shown on Pic 3.14 / 3.16 but do not tighten yet.
IMPORTANT: the central steel stopper is supplied with every
Activa+ motor group. If the door is equipped with an Automatic
Lock (optional), the central steel stopper must NOT be installed.
Please refer to step S6 for installation instructions of the automatic
lock.

Pic 3.14

Pic 3.15

100

Pic 3.16

Pic 3.15 Pic 3.16

05 M s3
 ACTIVA+ SINGLE LEAF OPERATOR INSTALLATION S3

4b- OPERATOR WITH LEFT SIDE OPENING

manusa

i
1.- Fix the central steel stopper to the rail nut supplied, and Tools
secure it at 100 mm from the right end of the main pofile. Pic
3.17 / 3.19
2.- Fix the side stopper on the left end of the track rail as shown
on Pic 3.17 / 3.18 but do not tighten yet nº10

IMPORTANT: the central steel stopper is supplied with every

Activa+ motor group. If the door is equipped with an Automatic
Lock (optional), the central steel stopper must NOT be installed.
Please refer to step S6 for installation instructions of the automatic
lock.

Pic 3.17

100
Pic 3.19

Pic 3.18

Pic 3.18 Pic 3.19

06 M s3
DTMJOVL101EN - v1 - ENGLISH ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S4

Activa+ single slide operator

Installation Step #4
Assembly of the motor group

1- WHERE TO FIND THE NECESSARY ELEMENTS

* Only one reference will be delivered

Ref. Description Location
Ref. Description Location * BRCVLT Activa+ SS dragging arm Box #1
GV Activa+ motor group Box #1 * KEGV15LT Activa+ SS extension kit Box #1

2- DOORS WITH CLEAR WIDTH (CW) < 1000 mm

2.1- MOUNT THE MOTOR GROUP ONTO THE MAIN PROFILE

i
Tools
1.- Fix the motor group at 250 mm of one end of the main profile, observing the opening
direction of the sliding leaf:

- If the door opens to the right: fix at 250 mm of the left end of the main profile Pic 4.1 nº10

- If the door opens to the left: fix at 250 mm of the right end of the main profile Pic 4.2

01 M s4
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S4

2.1a- OPERATOR WITH RIGHT SIDE OPENING

asunam

250

Pic 4.1

2.1b- OPERATOR WITH LEFT SIDE OPENING

manusa

250

Pic 4.2

02 M s4
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S4

2.2- FIX THE DRAGGING ARM TO THE BELT

i
1.- Fix the dragging arm of the outer trolley to the drive belt Pic 4.3 / 4.4 Tools

nº3

Pic 4.3 manusa

Pic 4.4 asunam

03 M s4
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S4

3- DOORS WITH CLEAR WIDTH (CW) BETWEEN 1001 AND 1400 MM

i
If the clear opening width (CW) is bigger than 1000 mm, an extension kit ref. KEGV15LT Tools
is required. Should this be the case, please read carefully the following instructions:

a.- Drive belt: the standard 2350 mm belt must be replaced with a 3120 mm belt, which
can be found in the extension kit KEGV15LT.Pic 4.5 Saw

b.- Motor group: must split in two parts. Use a metal saw to cut the steel base on the
left side of the motor group (it is marked from origin), no matter the opening direction
of the operator or the number of motors. Pic 4.5

Pic 4.5

3.1- MOUNT THE MOTOR GROUP ONTO THE MAIN PROFILE

i
Tools
1.- Mount the two parts of the Activa+ motor group onto the main profile observing the
distance to one end of the main profile as shown on Pic 4.6 / 4.7. Leave the screws
still loose to let both parts slide on the main profile until the corect position is found.
nº10

04 M s4
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S4

3.1a- OPERATOR WITH RIGHT SIDE OPENING

asunam

250

Pic 4.6

3.1b- OPERATOR WITH LEFT SIDE OPENING

manusa

250

Pic 4.7

05 M s4
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S4

3.2- FIX THE DRAGGING ARM TO THE EXTENSION BELT

i
1.- Fix and secure both ends of the drive belt to the dragging armPic Tools
4.8 / 4.9.

nº3

Pic 4.8 manusa

Pic 4.9 asunam

3.3- ADJUST AND SECURE THE MOTOR GROUP

i
1.- Slide the opposite end of the motor group until the drive belt has the Tools
right tension. Secure the motor group to the main profile, tightening the
screws to the rail nuts. Pic 4.10 / 4.11

nº10

Pic 4.10 manusa

Pic 4.11 manusa

on
ight tensi
h a s the r
it
until on
Slide ensi
h e r ight t
t
it has
l i d e until
S

06 M s4
DTMJOVL101EN - v1 - ENGLISH ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S5

Activa+ single slide operator

Installation Step #5
Cover assembly
1- WHERE TO FIND THE NECESSARY ELEMENTS

Ref. Description Location Ref. Description Location Ref. Description Location

KSCVCC02 Activa+ plastic end caps Box #2 PACVCI29 Bottom cover Box #2 JUCI Rubber hinge for bottom cover Box #2

Ref. Description Location Ref. Description Location Ref. Description Location

PACVCFPS29 Front cover Box #2 KSCVCC01 Activa+ cover suspension pack Box #2 GV Activa+ motor group Caja#1
Box 1

2- PREPARE THE BOTTOM COVER

i
IMPORTANT: All aluminium profiles (bottom and front covers) Tools
as well as the rubber hinge must be cut down to size, as per the
cutting dimensions shown on point no. 6 of Step 2 in this manual.

Saw

01 M s5
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S5

Pic 5.1

i Pic 5.3
1.- Slide 6 nuts through the rail on the bottom Tools
cover. 3 nuts are used to fix the suspension
brackets. 1 pc is used to fix the central steel
stopper or the automatic lock (optional). Pic
5.1. The 2 nuts on both ends are used to fix nº10
the plastic end caps. Pic 5.14

2.- Assemble the steel suspension brackets

to the bottom cover profile using the screws
supplied. Pic 5.2 / 5.3 The position of these
brackets is determined by the type of operator,
hence we suggest to assemble them only
when fixing the cover to the operator.

Pic 5.2

02 M s5
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S5

3- ASSEMBLE THE COVER CLIPS

i Pic 5.4
1.- Insert a M6x10 screw into the cover clips. Pic 5.4 Tools

2.- Fix 3 clips to the steel brackets Pic 5.5 / 5.6

nº10

Pic 5.6

Pic 5.5

Pic
Fig 5.6

03 M s5
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S5

4- ASSEMBLY OF THE HEADER FRAME

i
Tools
1.- Screw the central steel stopper or the
automatic lock to the bottom cover.
Pic 5.7 / 5.8
nº10
2.- Mount the bottom cover onto the main profile
using the suspension brackets as shown on
Pic 5.7 / 5.9

Pic 5.8

Pic 5.7
asunam

Pic 5.9

Pic 5.8 Pic 5.9

04 M s5
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S5

5- SLIDE THE RUBBER HINGE AND MOUNT THE END CAPS

i Pic 5.12
1.- Slide the rubber hinge into the bottom cover. Pic 5.12 Tools

2.- Fix the plastic end caps on both ends as shown on Pic
5.13 / 5.14
nº10 star
3.- Use the 2 clips on both ends to attach the plastic end
caps to the header frame Pic 5.13 / 5.14

Pic 5.13
asunam

Pic 5.14

Pic 5.14 Pic 5.14

05 M s5
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S5

6- ASSEMBLE THE FRONT COVER TO THE HEADER FRAME

i
1.- Assemble the front cover to the header frame, sliding the rubber hinge
into the front cover.

2.- To close the operator, lift the cover and tighten it to the main profile using
the 8 clips supplied Pic 5.15 / 5.16

Pic 5.15
asunam

Pic 5.16

Pic 5.16 Pic 5.16

06 M s5
DTMJOVL101EN - v1 - ENGLISH ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S6

Activa+ single slide operator

Installation Step #6

O
PT
Automatic lock CJGV03

1- WHERE TO FIND THE NECESSARY ELEMENTS

TECHNICAL FEATURES

1.- Operation by step motor

2.- Two positions: Open / Close, bi-stable in the event of a power failure.

Important:
If a central steel stopper is being used, it must be removed prior to
installing the automatic lock.

It is recommended to remove the front and bottom covers before

Ref. Description Location
assembling the automatic lock. On a new installation, fix the lock
CJGV03 Activa+ automatic lock Box #1
before assembling the cover.

2- BEFORE INSTALLING THE AUTOMATIC LOCK

i
1.- If the operator is equipped with a cover, remove the bottom cover before Tools
installing the automatic lock.

2.- If the operator is equipped with a central steel stopper, it must be removed
prior to installing the automatic lock. Pic 6.1 nº10

Pic 6.1
asunam

01 M s6
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S6

i Pic 6.2
1.- Dettach the manual handle from the lock Pic 6.2

3- INSTALL THE AUTOMATIC LOCK

i
Tools
1.- Fix the lock onto the main profile using the screws and rail nut supplied, but leaving the screws
4-the
still loose to let the lock slide on INSTALL ANDuntil
main profile CENTRE
the finalTHE AUTOMATIC
position LOCK
is found. Pic 6.3

2.- Fix the lock at 100 mm of the left end of the main profile if the operator opens to the right;
nº10
or at 100 mm of the right end, if the operator opens to the left Pic 6.4 / 6.5. Make sure you leave a
3 mm gap between the steel stopper and the lock hook. Adjust the steel stopper right or left until
the right position is found. Pic 6.6

3.- Secure the lock to the main profile tightening the fixing screws to the rail nut. Then assemble
the manual handle Pic 6.7

Pic 6.3
manusa

Pic 6.4 manusa

Pic 6.5 manusa

3 mm 3 mm
100 mm 100 mm

02 M s6
 ACTIVA+ SINGLE SLIDE OPERATOR INSTALLATION S6

i
1.- Connect the automatic lock to the control board using the
extension cable. Slide the cable through the bottom cover and
secure it using the clips supplied. Connect the white connector
on one end to the control board. Pic 6.14 / 6.15

2.- Connect the black connector to the automatic lock Pic 6.14
/ 6.16

Pic 6.14
asunam

Pic 6.15

Pic 6.16

Pic 6.15 Pic 6.16

05 M s6
DTMJOVL101EN - v1 - ENGLISH ACTIVA+ SINGLE SLIDE OPERATOR - INSTALLATION MANUAL S7

Activa+ single slide operator

Installation Step #7
Fixing the operator to the wall
1- WHERE TO FIND THE NECESSARY ELEMENTS

Ref. Description Location Ref. Description Location

------- Assemblied Activa+ operator ------- KSCVPC01 Activa+ front suspension pack Box #2

2- PREPARATORY STEPS BEFORE INSTALLATION

i
IMPORTANT: It is easier to install the operator in its final position if its front and bottom covers are removed.

Pic 7.1

01 M s7
 ACTIVA+ SINGLE SLIDE OPERATOR - INSTALLATION MANUAL S7

Plumb line Interior and exterior

Operator

IO R
ER
A vertical reference EXT
line to guide installation

R
IO
R
of the door.

TE
IN
The plumb line shall be used as a reference line throughout the
installation process. Its position corresponds to the rear face of For these doors, the side where the operator is located, which is
the main profile of the operator, whichever type of suspension is also the side where the sliding leaves are placed, is considered to
used (front or side suspension). be the interior side.

3- FRONT SUSPENSION

i
1.- Drill 5 holes at the positions indicated in Fig. 7.2, in the surface Tools
on which the operator is to be suspended.

lead drill dia 10

OW (min) = (2xCW)+100
25 = = = = 25

50 100

CH OH
CH

FW left CW

HW

Pic 7.2

02 M s7
 ACTIVA+ SINGLE SLIDE OPERATOR - INSTALLATION MANUAL S7

Front suspension to a wall Front suspension to a 80 mm C-beam

4 4

50 50

OH=CH+100 OH=CH+100

CH + 50 CH + 50

20

CH CH

A vertical reference A vertical reference

line to guide installation line to guide installation
of the door. of the door.

The drawing shows the basic measurements required to attach the The drawing shows the basic measurements required to attach the
operator frontally to the wall. operator frontally to the 80 mm C-beam.
IMPORTANT: Mark the reference line shown both vertically and on IMPORTANT: Mark the reference line shown both vertically and on
the floor. To determine the position of the reference line, consult the the floor. To determine the position of the reference line, consult the
door-leaf installation manual, since the position will vary, depending door-leaf installation manual, since the position will vary, depending
on which type of profile is used. on which type of profile is used.

03 M s7
NOTE: The technical specifications described in this manual are given for information purposes HEAD OFFICE FACTORY
only, and do not represent any contractual obligation for Manusa. Edif. TESTA-10, 4º Polígono Industrial Km. 1,2
Avda. Vía augusta, 71-73 43800 Valls - Tarragona (España)
Manusa reserves the right to modify in any moment and without prior notice the technical
08174 Sant Gugat del Vallés Tel.+34 902 321 700
specifications displayed in this manual, whenever it is considered to improve the product.
Barcelona - España Fax+34 902 321 750
Last revision: May 2006 Tel. +34 902 321 400 www.manusa.com
Fax +34 902 321 450