dIXEL Installing and Operating Instructions 1592009000

KEY COMBINATIONS

WING
+ To lock and unlock the keyboard.

XW220L + To enter the programming mode.

1. GENERAL WARNING + To exit the programming mode.

1.1 PLEASE READ BEFORE USING THIS MANUAL 4.1 USE OF LEDS
• This manual is part of the product and should be kept near the instrument for easy and quick reference. Each LED function is described in the following table.
• The instrument shall not be used for purposes different from those described hereunder. It cannot be used
as a safety device. LED MODE Function
• Check the application limits before proceeding. ON The compressor is running

FLASHING - Programming Phase (flashing with LED )

- Anti-short cycle delay enabled
1.2 SAFETY PRECAUTIONS
FLASHING
• Check the supply voltage is correct before connecting the instrument. Programming Phase (flashing with LED )
• Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden ON The defrost is enabled
temperature changes with high atmospheric humidity to prevent formation of condensation
• Warning: disconnect all electrical connections before any kind of maintenance. ON The Fast Freezing cycle is enabled
• Fit the probe where it is not accessible by the End User. The instrument must not be opened.
ON - ALARM signal
• In case of failure or faulty operation send the instrument back to the distributor or to “Dixell S.p.a.” (see - In “Pr2” indicates that the parameter is also present in “Pr1”
address) with a detailed description of the fault.
• Consider the maximum current which can be applied to each relay (see Technical Data).
Function of the LEDs placed on the left top side of buttons:
• Ensure that the wires for probes, loads and the power supply are separated and far enough from each
other, without crossing or intertwining.
BUTTON MODE FUNCTION
• In case of applications in industrial environments, the use of mains filters (our mod. FT1) in parallel with
inductive loads could be useful. SET FLASHING The Set point is displayed and it can be modified
SET FAST FLASHING The Energy Saving is enabled
2. GENERAL DESCRIPTION DEFROST ON The Manual Defrost is activated
Model XW220L, 38x185 mm format, is microprocessor based controller suitable for applications on normal LIGHT ON The Light is ON
temperature refrigerating units. It is provided with two relay outputs to control compressor, and the lights ON/OFF ON The instrument is OFF
They are also provided with two NTC probe inputs, one for temperature control, one optional, for the display.
There are two digital inputs (free contact) for the door switch and configurable by parameter. 4.2 HOW TO SEE THE MIN TEMPERATURE
The standard TTL output allows the user to connect, by means of a TTL/RS485 external module, a ModBUS-
1. Press and release the à key.
RTU compatible monitoring system and to programme the parameter list with the “Hot Key”.
An optional output for remote display “XW-REP” is available. 2. The “Lo” message will be displayed followed by the minimum temperature recorded.
3. By pressing the à key or waiting for 5s the normal display will be restored.
3. CONTROLLING LOADS
4.3 HOW TO SEE THE MAX TEMPERATURE
3.1 THE COMPRESSOR
1. Press and release the è key.
The regulation is performed according to the temperature measured by the thermostat probe with a positive
2. The “Hi” message will be displayed followed by the maximum temperature recorded.
differential from the set point: if the temperature increases and reaches set point plus differential the compressor
is started and then turned off when the temperature reaches the set point value again. 3. By pressing the è key or waiting for 5s the normal display will be restored.
In case of fault in the thermostat probe the start and stop of the compressor are timed through parameters 4.4 HOW TO RESET THE MAX AND MIN TEMPERATURE RECORDED
“COn” and “COF”.
To reset the stored temperature, when max or min temperature is displayed :
3.2 FAST FREEZING 1. Press SET key until “rST” label starts blinking.

When defrost is not in progress, it can be activated the keypad by holding the è key pressed for about 3 N.B. After the installation RESET the temperature stored .
seconds. The compressor operates in continuous mode for the time set through the “CCt” parameter. The cycle
can be terminated before the end of the set time using the same activation key, è for about 3 seconds. 4.5 HOW TO SEE AND MODIFY THE SET POINT
1. Push and immediately release the SET key: the display will show the Set point value;
3.3 DEFROST 2. The SET LED start blinking;
The defrost interval is control by means of parameter “EdF”: (EdF=in) the defrost is made every “IdF” time, 3. To change the Set value push the è or à arrows within 10s.
(EdF=Sd) the interval “IdF” is calculate through Smart Defrost algorithm (only when the compressor is ON). 4. To memorise the new set point value push the SET key again or wait 10s.
Defrost is performed through a simple stop of the compressor. Parameter “IdF” controls the interval between
defrost cycles, while its length is controlled by parameter “MdF”. 4.6 TO START A MANUAL DEFROST
4. KEYBOARD
1. Push the DEF key for more than 2 seconds and a manual defrost will start.

4.7 TO ENTER IN PARAMETERS LIST “PR1”

To enter the parameter list “Pr1” (user accessible parameters) operate as follows:

1. Enter the Programming mode by pressing the Set and DOWN key for few
seconds ( and start blinking).

To display and modify target set point; in programming mode it selects a parameter or confirm an 2. The instrument will show the first parameter present in “Pr1”
operation.
By holding it pressed for 3s when max or min temperature is displayed it will be erased.
4.8 TO ENTER IN PARAMETERS LIST “PR2”
To see the max. stored temperature; in programming mode it browses the parameter codes or To access parameters in “Pr2”:
increases the displayed value. By holding it pressed for 3s the fast freezing cycle is started. 1. Enter the “Pr1” level.
2. Select “Pr2” parameter and press the “SET” key.
To see the min stored temperature; in programming mode it browses the parameter codes or 3. The “PAS” flashing message is displayed, shortly followed by “0 - -” with a flashing zero.
decreases the displayed value. 4. Use è or à to input the security code in the flashing digit; confirm the figure by pressing “SET”. The
security code is “321“.
5. If the security code is correct the access to “Pr2” is enabled by pressing “SET” on the last digit.
By holding it pressed for 3s the defrost is started.
Another possibility is the following: after switching ON the instrument the user can push Set and DOWN keys
within 30 seconds.
Switch ON and OFF the cold room light.
NOTE: each parameter in “Pr2” can be removed or put into “Pr1” (user level) by pressing “SET” + à. When a
Switch ON and OFF the instrument. parameter is present in “Pr1” LED is on.

1592009000 XW220L GB r1.2 06.07.06.doc XW220L 1/4

dIXEL Installing and Operating Instructions 1592009000
ALARMS
4.9 HOW TO CHANGE THE PARAMETER VALUE
ALC Temperature alarm configuration
1. Enter the Programming mode.
rE = High and Low alarms related to Set Point
2. Select the required parameter with è or à.
Ab = High and low alarms related to the absolute temperature.
3. Press the “SET” key to display its value ( and LED starts blinking). ALU High temperature alarm setting:
4. Use è or à to change its value. ALC= rE, 0 ÷ 50°C or 90°F
5. Press “SET” to store the new value and move to the following parameter. ALC= Ab, ALL ÷ 110°C or 230°F
To exit: Press SET + UP or wait 15s without pressing a key. when this temperature is reached and after the ALd delay time the HA alarm is enabled.
NOTE: the new programming is stored even when the procedure is exited by waiting the time-out. ALL Low temperature alarm setting:
ALC = rE , 0 ÷ 50 °C or 90°F
4.10 HOW TO LOCK THE KEYBOARD
ALC = Ab , - 50°C or -58°F ÷ ALU
1. Keep the è and à keys pressed together for more than 3 s the è and à keys. when this temperature is reached and after the ALd delay time, the LA alarm is enabled,.
2. The “POF” message will be displayed and the keyboard is locked. At this point it is only AFH Temperature alarm and fan differential: (0,1÷25,5°C; 1÷45°F) Intervention differential for temperature
possible the viewing of the set point or the MAX o Min temperature stored and to switch alarm set point, always positive.
ON and OFF the light, the auxiliary output and the instrument. ALd Temperature alarm delay: (0÷255 min) time interval between the detection of an alarm condition and the
corresponding alarm signalling.
TO UNLOCK THE KEYBOARD dAO Delay of temperature alarm at start-up: (0min÷23h 50min) time interval between the detection of the
temperature alarm condition after the instrument power on and the alarm signalling.
Keep the è and à keys pressed together for more than 3s. EdA Alarm delay at the end of defrost: (0÷255 min) Time interval between the detection of the temperature
alarm condition at the end of defrost and the alarm signalling.
dot Delay of temperature alarm after closing the door : (0÷255 min) Time delay to signal the temperature
4.11 ON/OFF FUNCTION alarm condition after closing the door.
By pushing the ON/OFF key, the instrument shows “OFF” for 5 sec. and the ON/OFF LED is doA Open door alarm delay:(0÷255 min) delay between the detection of the open door condition and its
switched ON. alarm signalling: the flashing message “dA” is displayed.
During the OFF status, all the relays are switched OFF and the regulations are stopped; if a nPS Pressure switch number: (0 ÷15) Number of activation of the pressure switch, during the “did” interval,
monitoring system is connected, it does not record the instrument data and alarms. before signalling the alarm event (I2F= PAL).
N.B. During the OFF status the Light and AUX buttons are active.
4.12 TO SEE THE PROBE VALUES PROBE INPUTS
Ot Thermostat probe calibration: (-12.0÷12.0°C/ -21÷21°F) allows to adjust possible offset of the
1. Enter in “Pr2” level.
thermostat probe.
2. Select “Prd” parameter with è or à. O3 Auxiliary probe calibration: (-12.0÷12.0°C/ -21÷21°F) allows to adjust possible offsets of the evaporator
3. Press the “SET” key to display “Pb1” label alternate with Pb1 value. probe.
4. Use è and à keys to display the other probe values. P2P Evaporator probe presence:
5. Press “SET” to move to the following parameter. n= not present: the defrost stops only by time; y= present: the defrost stops by temperature and time.
P3P Auxiliary probe presence: n= not present; y= present.
HES Temperature increase during the Energy Saving cycle : (-30,0°C ÷ 30,0°C / -22÷86°F) sets the
5. PARAMETER LIST increasing value of the set point during the Energy Saving cycle.
REGULATION DIGITAL INPUTS
Hy Differential: (0,1÷25,5°C; 1÷45°F): Intervention differential for set point, always positive. Compressor odc Compressor and fan status when open door:
Cut IN is Set Point Plus Differential (Hy). Compressor Cut OUT is when the temperature reaches the set no = normal;
point. Fan = normal;
LS Minimum set point limit: (-50,0°C÷SET; -58°F÷SET) Sets the minimum acceptable value for the set CPr = Compressor OFF;
point. F_C = Compressor OFF.
US Maximum set point limit: (SET÷110°C; SET÷230°F) Set the maximum acceptable value for set point. I1P Door switch input polarity:
OdS Outputs activation delay at start up: (0÷255 min) This function is enabled at the initial start up of the CL : the digital input is activated by closing the contact;
instrument and inhibits any output activation for the period of time set in the parameter. (Light can work) OP : the digital input is activated by opening the contact.
AC Anti-short cycle delay: (0÷30 min) interval between the compressor stop and the following restart. I2P Configurable digital input polarity:
CCt Thermostat override: (0min ÷23h 50min) allows to set the length of the continuous cycle. Can be used, CL : the digital input is activated by closing the contact;
for instance, when the room is filled with new products. OP : the digital input is activated by opening the contact
Con Compressor ON time with faulty probe: (0÷255 min) time during which the compressor is active in case I2F Digital input operating mode: configure the digital input function:
of faulty thermostat probe. With COn=0 compressor is always OFF. EAL = generic alarm;
COF Compressor OFF time with faulty probe: (0÷255 min) time during which the compressor is off in case of bAL = serious alarm mode;
faulty thermostat probe. With COF=0 compressor is always active. PAL = Pressure switch;
CH Type of action : CL (COOL); Ht (HEAT) dFr = Start defrost;
AUS = not used;
DISPLAY Es = Energy Saving;
CF Temperature measurement unit: °C = Celsius; °F = Fahrenheit. When the measurement unit is onF = remote On/OFF.
changed the SET point and the values of some parameters have to be modified did Time interval/delay for digital input alarm:(0÷255 min.) Time interval to calculate the number of the
rES Resolution (for °C): (in = 1°C; de = 0,1°C) allows decimal point display. pressure switch activation when I2F=PAL. If I2F=EAL or bAL (external alarms), “did” parameter defines
de = 0,1°C the time delay between the detection and the successive signalling of the alarm.
in = 1 °C SAA Set Point for anti-condensing heater: (-50,0÷110,0°C; -58÷230°F) defines the room temperature
Lod Local display : select which probe is displayed by the instrument: setpoint to switch on the anti-condensing heater.
P1 = Thermostat probe
P2 = Not used OTHER
P3 = auxiliary probe Adr RS485 serial address (1÷247): Identifies the instrument address when connected to a ModBUS
1r2 = Not used compatible monitoring system.
Red Remote display : select which probe is displayed by the remote display (XW-REP) Rel Release software: (read only) Software version of the microprocessor.
P1 = Thermostat probe Ptb Parameter table: (read only) it shows the original code of the dIXEL parameter map.
P2 = Not used Prd Probes display: (read only) display the temperature values of the evaporator probe Pb2 and the auxiliary
P3 = auxiliary probe probe Pb3.
1r2 = Not used Pr2 Access to the protected parameter list (read only).
6. DIGITAL INPUTS
DEFROST
The Wing series can support up to 2 free contact digital inputs. One is always configured as door switch, the
EdF Defrost mode:
second is programmable in seven different configurations by the “I2F” parameter.
in = interval mode. The defrost starts when the time “Idf” is expired.
Sd = Smartfrost mode. The time IdF (interval between defrosts) is increased only when the compressor 6.1 DOOR SWITCH INPUT
is running (even non consecutively).
It signals the door status and the corresponding relay output status through the “odc” parameter:
IdF Interval between defrosts: (1÷120h) Determines the time interval between the beginning of two defrost
no = normal;
cycles.
Fan = normal;
MdF (Maximum) duration of defrost: (0÷255 min) it sets the maximum length for defrost.
CPr = Compressor OFF;
dFd Display during defrost:
F_C = Compressor OFF.
rt = real temperature;
Since the door is opened, after the delay time set through parameter “dOA”, the alarm output is enabled and the
it = temperature reading at the defrost start;
display shows the message “dA”. The alarm stops as soon as the external digital input is disabled again. During
Set = set point;
this time and then for the delay “dot” after closing the door, the high and low temperature alarms are disabled.
dEF = “dEF” label;
dEG = “dEG” label;
dAd Defrost display time out: (0÷255 min) Sets the maximum time between the end of defrost and the 6.2 CONFIGURABLE INPUT - GENERIC ALARM (EAL)
restarting of the real room temperature display. As soon as the digital input is activated the unit will wait for “did” time delay before signalling the “EAL” alarm
dPO First defrost after start-up: message. The outputs status don’t change. The alarm stops just after the digital input is de-activated.
y = Immediately;
n = after the IdF time
dAF Defrost delay after fast freezing: (0min÷23h 50min) after a Fast Freezing cycle, the first defrost will be
delayed for this time.

1592009000 XW220L GB r1.2 06.07.06.doc XW220L 2/4

dIXEL Installing and Operating Instructions 1592009000
8. ELECTRICAL CONNECTIONS
6.3 CONFIGURABLE INPUT - SERIOUS ALARM MODE (BAL)
The instruments are provided with screw terminal block to connect cables with a cross section up to 2,5 mm2 for
When the digital input is activated, the unit will wait for “did” delay before signalling the “BAL” alarm message.
the digital and analogue inputs. Relays and power supply have a Faston connection (6,3mm). Heat-resistant
The relay outputs are switched OFF. The alarm will stop as soon as the digital input is de-activated.
cables have to be used. Before connecting cables make sure the power supply complies with the instrument’s
requirements. Separate the probe cables from the power supply cables, from the outputs and the power
6.4 CONFIGURABLE INPUT - PRESSURE SWITCH (PAL) connections. Do not exceed the maximum current allowed on each relay, in case of heavier loads use a suitable
external relay.
If during the interval time set by “did” parameter, the pressure switch has reached the number of activation of
N.B. Maximum current allowed for all the loads is 20A.
the “nPS” parameter, the “PAL” pressure alarm message will be displayed. The compressor and the regulation
are stopped. When the digital input is ON the compressor is always OFF.
8.1 PROBE CONNECTIONS
6.5 CONFIGURABLE INPUT - START DEFROST (DFR) The probes shall be mounted with the bulb upwards to prevent damages due to casual liquid infiltration. It is
recommended to place the thermostat probe away from air streams to correctly measure the average room
It executes a defrost if there are the right conditions. After the defrost is finished, the normal regulation will
temperature.
restart only if the digital input is disabled otherwise the instrument will wait until the “Mdf” safety time is expired.

6.6 CONFIGURABLE INPUT - ENERGY SAVING (ES)

9. TTL SERIAL LINE
The Energy Saving function allows to change the set point value as the result of the SET+ HES (parmeter) sum.
The TTL connector allows, by means of the external module TTL/RS485, to connect the unit to a network line
This function is enabled until the digital input is activated.
ModBUS-RTU compatible as the dIXEL monitoring system XJ500 (Version 3.0).
The same TTL connector is used to upload and download the parameter list of the “HOT KEY“.
6.7 CONFIGURABLE INPUT - REMOTE ON/OFF (ONF)
This function allows to switch ON and OFF the instrument. 10. USE OF THE PROGRAMMING “HOT KEY “
The Wing units can UPLOAD or DOWNLOAD the parameter list from its own E2 internal memory to the “Hot
6.8 DIGITAL INPUTS POLARITY Key” and vice-versa.
The digital inputs polarity depends on “I1P” and “I2P” parameters.
CL : the digital input is activated by closing the contact.
10.1 DOWNLOAD (FROM THE “HOT KEY” TO THE INSTRUMENT)
OP : the digital input is activated by opening the contact
1. Turn OFF the instrument by means of the ON/OFF key, remove the TTL serial cable if present, insert
the “Hot Key” and then turn the Wing ON.
7. INSTALLATION AND MOUNTING 2. Automatically the parameter list of the “Hot Key” is downloaded into the Wing memory, the “DoL”
Instruments XW220L shall be mounted on vertical panel, in a 150x31 mm hole, and fixed using two screws ∅ 3 message is blinking. After 10 seconds the instrument will restart working with the new parameters.
x 2mm. To obtain an IP65 protection grade use the front panel rubber gasket (mod. RG-L). The temperature 3. Turn OFF the instrument remove the “Hot Key”, plug in the TTL serial cable, then turn it ON again.
range allowed for correct operation is 0 - 60 °C. Avoid places subject to strong vibrations, corrosive gases, At the end of the data transfer phase the instrument displays the following messages:
excessive dirt or humidity. The same recommendations apply to probes. Let the air circulate by the cooling “end “ for right programming. The instrument starts regularly with the new programming.
holes. “err” for failed programming. In this case turn the unit off and then on if you want to restart the download again
or remove the “Hot key” to abort the operation.
7.1 CUT OUT

165
+1 10.2 UPLOAD (FROM THE INSTRUMENT TO THE “HOT KEY”)
-1

+0.5 1. Turn OFF the instrument by means of the ON/OFF key and remove the TTL serial cable if present; then
150 -0
turn it ON again.
2. When the Wing unit is ON, insert the “Hot key” and push è key; the "uPL" message appears.
+0.5

3. Push “SET” key to start the UPLOAD; the “uPL” message is blinking.
-0
31

4. Turn OFF the instrument remove the “Hot Key”, plug in the TTL serial cable, then turn it ON again.
At the end of the data transfer phase the instrument displays the following messages:
“end “ for right programming.
Ø3 x2 “err” for failed programming. In this case push “SET” key if you want to restart the programming again or
remove the not programmed “Hot key”.

7.2 MOUNTING WITH KEYBOARD COVER OPENING DOWNWARD 11. ALARM SIGNALS
Message Cause Outputs
“P1” Thermostat probe failure Alarm output ON; Compressor output according to
parameters “COn” and “COF”
“P3” Auxiliary probe failure Alarm output ON; Other outputs unchanged
2 CLICK! “HA” Maximum temperature alarm Alarm output ON; Other outputs unchanged
“LA” Minimum temperature alarm Alarm output ON; Other outputs unchanged
“EE” Data or memory failure Alarm output ON; Other outputs unchanged
“dA” Defrost timeout alarm Alarm output ON; Other outputs unchanged
1 “dAL” Door switch alarm Alarm output ON; Other outputs unchanged
3 “EAL” External alarm Alarm output ON; Other outputs unchanged
“BAL” Serious external alarm Alarm output ON; Other outputs OFF
“PAL” Pressure switch alarm Alarm output ON; Other outputs OFF
The alarm message is displayed until the alarm condition is recovery.
1
All the alarm messages are showed alternating with the room temperature except for the “P1” which is flashing.
2
1 3 To reset the “EE” alarm and restart the normal functioning press any key, the “rSt” message is displayed for
about 3s.
11.1 SILENCING BUZZER
Once the alarm signal is detected the buzzer and the relay are is silenced by pressing any key.
7.3 MOUNTING WITH KEYBOARD COVER OPENING UPWARD

11.2 “EE” ALARM

The dIXEL instruments are provided with an internal check for the data integrity. Alarm “EE” flashes when a
failure in the memory data occurs. In such cases the alarm output is enabled.

1 11.3 ALARM RECOVERY

2
Probe alarms : “P1” (probe1 faulty), and “P3”; they automatically stop 10s after the probe restarts normal
3 operation. Check connections before replacing the probe.
1 Temperature alarms “HA” and “LA” automatically stop as soon as the thermostat temperature returns to normal
values or when the defrost starts.
Door switch alarm “dA” stop as soon as the door is closed.
External alarms “EAL”, “BAL” stop as soon as the external digital input is disabled “PAL” alarm is recovered by
2 switching OFF the instrument.
3
2 CLICK! 12. TECHNICAL DATA
1
Housing: self extinguishing ABS.
Case: facia 38x185 mm; depth 76mm
Mounting : panel mounting in a 150x31 mm panel cut-out with two screws. ∅ 3 x 2mm.
Distance between the holes 165mm
Protection: IP20.
Frontal protection: IP65 with frontal gasket mod RG-L. (optional)
Connections: Screw terminal block ≤ 2,5 mm2 heat-resistant wiring and 6,3mm Faston
Power supply: 230Vac or. 110Vac ± 10%

1592009000 XW220L GB r1.2 06.07.06.doc XW220L 3/4

dIXEL Installing and Operating Instructions 1592009000
Power absorption: 7VA max. Pr2 Access parameter list --- --- Pr2
Display: 3 digits, red LED, 14,2 mm high.
Inputs: 2 NTC probes
Digital inputs: 2 free voltage
Relay outputs: Total current on loads MAX. 20A
compressor: relay SPST 20(8) A, 250Vac
light: relay SPST 16(3) A, 250Vac
Other output : alarm buzzer
Serial output : TTL standard
Communication protocol: Modbus - RTU
Data storing: on the non-volatile memory (EEPROM).
Kind of action: 1B.
Pollution grade: normal
Software class: A.
Operating temperature: 0÷60 °C.
Storage temperature: -25÷60 °C.
Relative humidity: 20÷85% (no condensing)
Measuring and regulation range: NTC probe: -40÷110°C (-58÷230°F)
Resolution: 0,1 °C or 1°C or 1 °F (selectable).
Accuracy (ambient temp. 25°C): ±0,5 °C ±1 digit

13. CONNECTIONS
13.1 XW220L

16A 20A XW220L

250Vac 250Vac MAX
20A

9 10 11 12 13 14 17 18 19 21 22 23
Door switch

Room
Digital inp.
Common

Display
Neutral
Line

Light Comp

14. DEFAULT SETTING VALUES

Label Name Range Default Level
REGULATION °C/°F XW220L
Set Set point LS÷US 3 Pr1
Hy Differential 0,1÷25,5 °C / 1÷45°F 2 Pr1
LS Minimum set point -50,0°C÷SET / -58°F÷SET -10 Pr2
US Maximum set point SET ÷ 110°C / SET ÷ 230°F 20 Pr2
OdS Outputs activation delay at start up 0÷255 min. 1 Pr2
AC Anti-short cycle delay 0÷30 min. 1 Pr1
CCt Compressor ON time during fast freezing 0 ÷ 23h 50 min. 0 Pr2
COn Compressor ON time with faulty probe 0÷255 min. 15 Pr2
COF Compressor OFF time with faulty probe 0÷255 min. 30 Pr2
CH Type of action CL÷Ht CL Pr2
DISPLAY
CF Temperature measurement unit °C ÷ °F °C Pr2
rES Resolution (integer/decimal point) in ÷ de de Pr1
Lod Local display P1 ÷ 1r2 P1 Pr2
Red Remote display P1 ÷ 1r2 P1 Pr2
DEFROST
EdF Defrost mode In, Sd In Pr2
IdF Interval between defrost cycles 1÷120h 8 Pr1
MdF (Maximum) length for 1° defrost 0÷255 min. 20 Pr1
dFd Displaying during defrost rt, it, SEt, dEF, dEG it Pr2
dAd MAX display delay after defrost 0÷255 min. 30 Pr2
dPO First defrost after start up n÷y n Pr2
dAF Defrost delay after fast freezing 0 ÷ 23h 50 min. 2 Pr2
ALARMS
ALC Temperature alarms configuration rE÷Ab rE Pr2
ALU MAXIMUM temperature alarm -50,0÷110°C/ -58÷230°F 10 Pr1
ALL minimum temperature alarm -50,0÷110°C/ -58÷230°F 10 Pr1
AFH Temperature alarm differential 0,1÷25,5 °C / 1÷45°F 2 Pr2
ALd Temperature alarm delay 0÷255 min. 15 Pr2
dAO Delay of temperature alarm at start up 0 ÷ 23h 50 min. 1.3 Pr2
EdA Alarm delay at the end of defrost 0÷255 min. 30 Pr2
dot Delay of temperature alarm after closing the door 0÷255 min. 15 Pr2
dOA Open door alarm delay 0÷255 min. 15 Pr2
nPS Pressure switch activation number 0÷15 0 Pr2
ANALOGUE INPUTS
Ot Thermostat probe calibration -12,0÷12,0°C / -21÷21°F 0 Pr1
O3 Auxiliary probe calibration -12,0÷12,0°C / -21÷21°F 0 Pr2
P3P Auxiliary probe presence n÷y n Pr2
HES Temperature increase during the Energy Saving -30÷30°C / -22÷86°F 0 Pr2
cycle
DIGITAL INPUTS
Odc Open door control
I1P Door switch polarity
no, Fan, CPr, F_C
CL÷OP
Fan
CL
Pr2
Pr2
dIXEL S.p.a.
Z.I. Via dell’Industria, 27 - 32010 Pieve d’Alpago (BL) ITALY
I2P Configurable digital input polarity CL÷OP CL Pr2 tel. +39 - 0437 - 98 33 - fax +39 - 0437 - 98 93 13
i2F Digital input configuration EAL, bAL, PAL, dFr, EAL Pr2 http://www.dixell.com E-mail: [email protected]
AUS, ES, OnF
dId Digital input alarm delay 0÷255 min. 5 Pr2
OTHER
Adr Serial address 0÷247 1 Pr1
rEL Software release --- 1.0 Pr2
Ptb Map code --- --- Pr2
Prd Probes display Pb1÷Pb3 --- Pr2

1592009000 XW220L GB r1.2 06.07.06.doc XW220L 4/4