Mipa Protector Truckbedliner schwarz

Technical data sheet page 1 / 5

Intended use
Highly resistant 2K polyurethane-acrylic paint for a scratch-resistant and robust black coating of truck bed surfaces (e.g. Pick-Up
truck beds) and of all heavy duty surfaces on commercial vehicles, off-road vehicles, camping cars, trailers and SUVs etc.

Possible application areas:

- bodies of SUVs and off-road vehicles

- rims of SUVs and off-road vehicles
- floors and storage areas in caravans
- underbodies and chassis
- bullbars, running boards, roof racks, spare wheel covers and so on
- fender well
- access ramps, decks of recovery vehicles and trailers

Beside its very high wear resistance Mipa Protector provides also an excellent mechanical and chemical resistance. The very
high vertical stability allows applying extremely high-build coatings. Easy to use since 750 ml paint material is already filled in 1
litre cans for underbody sealants. Just add 250 ml of the hardener Mipa 2K-Härter H 5 or H 10. Shake than the can vigorously
and apply the mixture using an underbody sealant spray gun or paint roller.

Properties:

- high UV and weathering resistance

- excellent shock and scratch resistance
- high resistance to fuels and oils
- excellent water resistance
- provides noise reduction
- short-term temperature exposure: 180 °C
- permanent temperature exposure: 150 °C

Spreading rate: 3 m²/l for 200 μm dry film thickness

Processing instructions

Colour
black

Mixing ratio
hardener by volume lacquer :hardener
Mipa 2K-Härter H 5 / H 10 3 : 1 or
750 ml Mipa Protector in 1,1 litre cans for underbody sealants +
250 ml Mipa 2K-Härter H 5 or H 10 + approx. 2 minutes shaking

Hardener
for complete paintwork for partial paintwork
Mipa 2K-Härter H 10 Mipa 2K-Härter H 5

Pot life
30 - 45 min with Mipa 2K-Härter H 5 at 20 °C
1 - 1,5 h with Mipa 2K-Härter H 10 at 20 °C

Version: en 0421
This technical data sheet is supplied for informational purposes only! According to our information, all data and recommendations correspond to the state of art and are based on years
of experience in manufacturing our products. They do not exempt the user from his obligation to verify professionally, on his own responsibility, the suitability of our products to the
intended purpose under prevailing conditions. Safety data sheets and warnings on packaging must be observed. We reserve the right to modify and to complete the information content
at any time, without prior notice or obligation to update.
MIPA SE · Am Oberen Moos 1 · D-84051 Essenbach · Tel.: +49(0)8703/922-0 · Fax: +49(0)8703/922-100 · [email protected] · www.mipa-paints.com
Mipa Protector Truckbedliner schwarz
Technical data sheet page 2 / 5

Mixing procedure for applications with underbody sealant spray gun (UBS)
1. Shake vigorously Mipa Protector paint material.
2. Open the can, add 250 ml of hardener, close the lid and shake vigorously for approx. 2 minutes.

Mixing procedure for applications with gravity spray guns / paint roller
1. Shake vigorously Mipa Protector paint material.
2. Pour the paint in a mixing cup, add the hardener in a mixing ratio of 3 : 1 by volume and mix thoroughly.
3. Add the thinner and mix thoroughly.

Now the mixture is ready to be applied by spraying or rolling!

Thinner
Mipa 2K-Verdünnung

Spray viscosity
Gravity spray gun UBS spray gun / roller
See application mode undiluted

Application mode

Application mode nozzle dilution How to apply a rough texture

(mm)
MP SprayGun - - 1. Apply a uniform coat with a pressure setting of
UBS/HV 2 - 4 bar until full coverage is achieved.
2. Observe flash-off time of between 10 min and 1
h.
3. To achieve the desired texture reduce the
pressure to 1 - 1,5 bar and increase the spray
distance up to approx. 45 - 60 cm.
HVLP 2,5 10 % 1. Apply a uniform coat with a pressure setting of
(low pressure) 2 bar until full coverage is achieved.
2. Observe flash-off time of between 10 min and
1h.
3. To achieve the desired texture reduce the
pressure to approx. 1 bar and increase the
spray distance to approx. 40 - 50 cm.

Texture roller - - 1. Apply evenly and overlapping with a texture

roller, e.g. MP Strukturroller, until opacity is
achieved. If full hiding power is not yet
achieved, a second coat can be applied after
an intermediate flash-off time of approx. 20
min.

Version: en 0421
This technical data sheet is supplied for informational purposes only! According to our information, all data and recommendations correspond to the state of art and are based on years
of experience in manufacturing our products. They do not exempt the user from his obligation to verify professionally, on his own responsibility, the suitability of our products to the
intended purpose under prevailing conditions. Safety data sheets and warnings on packaging must be observed. We reserve the right to modify and to complete the information content
at any time, without prior notice or obligation to update.
MIPA SE · Am Oberen Moos 1 · D-84051 Essenbach · Tel.: +49(0)8703/922-0 · Fax: +49(0)8703/922-100 · [email protected] · www.mipa-paints.com
Mipa Protector Truckbedliner schwarz
Technical data sheet page 3 / 5

Application mode nozzle dilution How to apply a medium texture

(mm)
MP SprayGun - - 1. Apply a uniform coat with a pressure setting of
UBS/HV 2 - 4 bar until full coverage is achieved.
2. Observe flash-off time between of 10 min and
1 h.
3. To achieve the desired texture reduce the
pressure to approx. 2 bar and increase the
spray distance to approx. 45 - 60 cm.
HVLP 2,0 - 2,5 15 % 1. Apply a uniform coat with a pressure setting of
(low pressure) 2 bar until full coverage is achieved
2. Observe a flash-off time between of 10 min
and 1 h.
3. To achieve the desired texture reduce the
pressure to approx. 1,5 bar and increase the
spray distance to approx. 45 - 60 cm.

Short nap roller - - 1. Apply evenly and overlapping with a short nap
roller, e.g. MP Heizkörperwalze Masterstreif,
until opacity is achieved. If full hiding power is
not yet achieved, a second coat can be applied
after an intermediate flash-off time of approx.
20 min.

Application mode nozzle dilution How to apply a fine texture

(mm)
MP SprayGun - - 1. Apply a uniform coat with a pressure setting of
UBS/HV 2 - 4 bar until full coverage is achieved.
2. Observe flash-off time of between 10 min and
1 h.
3. To achieve the desired texture, set the
pressure to 3 - 4 bar and increase the spray
distance to approx. 90 cm.
HVLP 1,6 - 1,8 20 % 1. Apply a uniform coat with a pressure setting of
(low pressure) 2 bar until full coverage is achieved.
2. Observe a flash-off time of between 10 min
and 1 h.
3. To achieve the desired texture reduce the
pressure to approx. 2 bar and increase the
spray distance to approx. 60 cm.

Foam roller - - 1. Apply evenly and overlapping with a foam

roller, e.g. MP Heizkörperwalze Premium, until
opacity is achieved. If full hiding power is not
yet achieved, a second coat can be applied
after an intermediate flash-off time of approx.
20 min.

Flash-off time
10 - 60 min between coats
10 - 15 min prior to oven drying

Dry film thickness

100 - 380 μm

Version: en 0421
This technical data sheet is supplied for informational purposes only! According to our information, all data and recommendations correspond to the state of art and are based on years
of experience in manufacturing our products. They do not exempt the user from his obligation to verify professionally, on his own responsibility, the suitability of our products to the
intended purpose under prevailing conditions. Safety data sheets and warnings on packaging must be observed. We reserve the right to modify and to complete the information content
at any time, without prior notice or obligation to update.
MIPA SE · Am Oberen Moos 1 · D-84051 Essenbach · Tel.: +49(0)8703/922-0 · Fax: +49(0)8703/922-100 · [email protected] · www.mipa-paints.com
Mipa Protector Truckbedliner schwarz
Technical data sheet page 4 / 5

Drying time
Object dust dry set to touch ready for sandable recoatable
temperature. assembly
20 °C 15 - 20 min 3-4h 24 h -- --
60 °C -- 30 min 1-2h -- --
Fully cured after 7 days (at 20 °C).

Note
Storage: at least 3 years in unopened original container.

VOC Regulation: EU limit value for this product of category A/j: 500 g/l - B/e 840 g/l
This product contains max. 500 g/l of VOC.

Processing conditions : from +10 °C and up to 80 % relative air humidity. Ensure adequate air ventilation.

Substrate preparation: steel: clean, sand slightly if necessary (remove any rust and mill scale) and degrease with Mipa
Silikonentferner

zinc: clean the surface with the ammonia solution Mipa Zinkreiniger

aluminium: clean, sand slightly and degrease with Mipa Silikonentferner

plastic substrates: Before application, reheat the object to be painted for 60 minutes at 60°C.
Degrease the surface thoroughly with Mipa Kunststoffreiniger antistatisch or Mipa
Silikonentferner

sand with MP Softpad super fine using Mipa Kunststoffreiniger antistatisch or Mipa
Silikonentferner. Clean again with Mipa Kunststoffreiniger antistatisch or Mipa Silikonentferner

allow parts to dry completely

ATTENTION: Releasing agents must be removed completely! After the previously mentioned
preparation, we recommend doing a wetting test with water. If the water rolls off quickly, repeat
the pre-treatment.

Application of Mipa adhesion promoters or primers for plastic substrates: e.g. Mipa 1K-Kunst-
stoffprimer, Mipa 1K-Haftpromoter, Mipa 1K-Plastic-Grundierfiller, Mipa 2K-Multifiller, etc.

Due to very different kinds of plastics and mixtures available on the market, we recommend
testing beforehand on the original plastic substrate.

wooden substrates: clean, sand slightly and dust off

GRP: clean, sand slightly and degrease with Mipa Silikonentferner

sound 2K-resistant paintworks: clean, sand slightly and degrease with Mipa Silikonentferner

Proposed coating structure: steel, zinc and aluminium:

priming coat: suitable Mipa 1K and 2K primer and filler (e. g. Mipa Rapidfiller, Mipa Aktivprimer,
Mipa 2K-Primer CF, Mipa 2K-Multifiller, Mipa EP-Primer Surfacer)

finishing coat: Mipa Protector (film thickness: 100 - 380 μm)

Version: en 0421
This technical data sheet is supplied for informational purposes only! According to our information, all data and recommendations correspond to the state of art and are based on years
of experience in manufacturing our products. They do not exempt the user from his obligation to verify professionally, on his own responsibility, the suitability of our products to the
intended purpose under prevailing conditions. Safety data sheets and warnings on packaging must be observed. We reserve the right to modify and to complete the information content
at any time, without prior notice or obligation to update.
MIPA SE · Am Oberen Moos 1 · D-84051 Essenbach · Tel.: +49(0)8703/922-0 · Fax: +49(0)8703/922-100 · [email protected] · www.mipa-paints.com
Mipa Protector Truckbedliner schwarz
Technical data sheet page 5 / 5

wooden substrates:

priming coat: Mipa EP-Grundierfiller or Mipa EP-Primer Surfacer

finishing coat: Mipa Protector (film thickness: 100 - 380 μm)

GRP, sound 2K-resistant paintworks:

finishing coat: Mipa Protector (film thickness: 100 - 380 μm)

or with priming coat, if irregularities must be levelled:

priming coat: suitable Mipa 2K primer and filler (e. g. Mipa 2K-Multifiller,
Mipa 4+1 Acrylfiller HS, Mipa 2K-HS-Grundfiller F 54)

Application notes: To ensure that the desired structure is achieved, we recommend making a sample.

Texture and gloss affect the colour.

To achieve an uniform texture apply the second layer as drop coat.

Spray distance and spray pressure change the texture.

Maskings or adhesive tapes which have been overcoated with Mipa Protector, must be
removed immediately after application. Otherwise the fresh paint will be peeled off with the
adhesive tape.

Not suitable to coat very oily and highly resinous woods (e.g. teak).

To obtain a non-slip surface just add 5-10% by weight of Mipa Grip-Additiv to the mixture of
basic paint + hardener. Stir thoroughly Mipa Grip-Additiv in the mixture and apply immediately.

Version: en 0421
This technical data sheet is supplied for informational purposes only! According to our information, all data and recommendations correspond to the state of art and are based on years
of experience in manufacturing our products. They do not exempt the user from his obligation to verify professionally, on his own responsibility, the suitability of our products to the
intended purpose under prevailing conditions. Safety data sheets and warnings on packaging must be observed. We reserve the right to modify and to complete the information content
at any time, without prior notice or obligation to update.
MIPA SE · Am Oberen Moos 1 · D-84051 Essenbach · Tel.: +49(0)8703/922-0 · Fax: +49(0)8703/922-100 · [email protected] · www.mipa-paints.com