Leader in Electrics & Automation

Tri-MEC
Ring Main Units
Medium Voltage Secondary Distribution
Ring Main Units Up to 24kV, SF6-Insulated

Electric Equipment
Ring Main Units

Technology
Safety
Durability and usefulness
Saving Cost
CONTENTS: Applications 4

Features 5

Configurations 6

Modules 8

Medium Voltage Ring switch module (RPL) 8

Fuse-switch module (RPF) 9

Secondary Distribution Circuit breaker module (RVB) 10

Ring Main Units Outer assembly 11

RPS 11
Up to 24kV,
RPF 12

SF6-Insulated RPL 13

RVB 14

RBR 15

Cable termination 16
Ring switch / Circuit breaker 16

Fuse-switch 16

Pannel connection 18

Accessories 19

Installation 24

Technical data 25

Quality assurance 26
Ring Main Units
Applications Tri-MEC

Tri-MEC is designed for use in the following

applications:
•Compact secondary substations
•Small industries
•Wind power plants
•Hotels, shopping centers, office buildings, business centers etc.
•Light mining applications, airports, hospitals, tunnels and underground railways

Generation Transmission Distribution(24kV)

Substation
Commercial &
Transmission Industrial
line customers

Power plant

Note) Application range.

4
Features

Technology
•Metal enclosed unit for indoor installation and type tested.
•Insulated by SF6 Gas
•Independent of climate.
•ON-OFF-EARTH, three position load break switch.

Safety
•Approachable and operable safely in the presence of power in the cables.
•Clear indication of operation status via mimic diagram on front panel.
•Fully automatic interlocking system.
•Voltage detector to check the presence of voltage in the cable.

Durability and usefulness

•Metal enclosed tank is hermetically sealed, it means this is independent of
environmental effects such as dirt, small insects, and moisture and so on.
•Load break switch operating is possible in the front of Ring Main Units.
•All switching operations can be made safely to personnel because of interlocking
system that operates automatically according to the switch position by the operator.
•Remote operation available in case of using motor mechanism.
•Fuse LBS will be tripped by a fuse striker pin connected to the mechanism
in the event of fault happening.
•Individual panels and panel blocks can be freely combined and extended.

Saving cost
•Only a little maintenance is required except replacement of HRC Power fuse after installation.
•Compact design that requires minimum space to install and operate locally is
main advantage especially where the space is limited.
•Materials can be recycled after the end of its service life.

5
Ring Main Units
Configurations

General
Tri-MEC RMU is an extensible and non-extensible ring main unit for the secondary distribution
network. Tri-MEC RMU can be supplied in various different configurations suitable for most
switching applications in 24 kV distribution networks.
When combined with the Tri-MEC RMU, they represent a complete solution for 24kV
secondary distribution networks. Tri-MEC RMU is a completely sealed system with a stainless
steel tank, gas tight metal enclosure, containing all the live parts, Switching-disconnector, earth
switch, Fuse switch, the circuit breaker.
A sealed steel tank filled with SF6 gas ensures a high level of reliability as well as safety and a
maintenance-free system. The Tri-MEC RMU offers the user a choice of either a switch-
disconnector combined with fuse or circuit breaker with relay for protection of the transformer.
Tri-MEC RMU can be controlled completely with an feeder remote unit. Most of this switchgear
exists in version that are extensible on the right or on both sides, in order to provide for future
development.

Information of model name

P: Puffer
D: Double feeder
V :V.I
U: Upside down
B: Bus

R
RMU L: LBS R: Rising
F: Fuse S: Standard
B: Breaker

Non-Extensible type
RPS
<2 LBS + 1 Fused LBS>

LBS LBS LBS

1535

VD Fuse VD

1502
706

Weight: 400kg
RPF(1R1F)
<1 Fused LBS + Bus rising>

* S LBS
1537

Fuse VD
695

SA *
1061 706

880

Note) *: Option Weight: 275kg

6
Configurations

Extensible type
RPL <LBS Panel>

LBS

1750
VD

0
456 73

Weight: 210kg

RPF <Fused switch Panel>

* S LBS

1750
Fuse

683
611 730

765
Weight: 275kg

RVB <Circuit Breaker Panel>

VCB Trip
1750

2×CT OC
*

520 730
Weight: 260kg

RBR <Bus Rising Panel>

1750
683

VD

456 730

765 Weight: 160kg

Note) *: Option
7
Ring Main Units
Modules

Ring switch module (RPL)

LBS

VD

< ON position > < OFF position > < EARTH position >

EARTHING
EARTHING LOAD BREAK
LOAD EARTHING
EARTHING LOAD BREAK
LOAD EARTHING
EARTHING LOAD BREAK
LOAD
SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH

Open Open Open Open Open Open

Earth
Ear th Close Earth
Ear th Close Earth
Ear th Close

Feature
•Three position load break switch and earthing switch.
•Indicator of switch position for load break switch and earthing switch.
•Voltage indicator lamp on panel makes it possible to check the presence of voltage in the cables.
•Pressure gage indicates status of SF6 gas tank and make it check leakage of gas.
•Intelligent interlock system
: To switch to Earth position, it should pass "OFF" position from "ON" position
•Applied high-speed rotary puffer type for extinction of arc.
•Dead front structure: It prevents an accident of touching because the live part is not exposed.
•Electrical (Remote/Local)operation :
operated by controller which can communicate with FRU (Feeder Remote Unit)
•Busbars, 630A

8
Fuse-switch module (RPF)

A
*
S LBS
B

Fuse

Note) *: Option

< ON position > < OFF position > < EARTH position >

B
B C

Close Close Close

Open Open Open

FUSE SWTICH FUSE SWTICH FUSE SWTICH

Open Earth
Ear th Open Earth
Ear th Open Earth
Ear th

EARTHING
EARTHING SWITCH EARTHING
EARTHING SWITCH EARTHING
EARTHING SWITCH

Feature
•Fuse rating: 24kV, Max 63A HRC power fuse
•Indicator of switch position for load break switch and earthing switch
•The Fuses conforming to DIN 43625 are used.
•Automatically tripped to protect from fault current when a fuse is blown
•Applied high-speed rotary puffer type for extinction of arc.
•Dead front structure: It prevents an accident of touching because the live part is not exposed.
•Busbars 200A
•Option: CTD (Condensor Trip Device)

9
Ring Main Units
Modules

Circuit breaker module (RVB)

VCB Trip

2×CT OC
*

Note) *: Option

< Spring charge

< ON position > < OFF position >
indicator >

Mechanism operation time

Feature
•200A vacuum circuit breaker
•Rated breaking time: 3cycle
•Latched mechanism - close and open coil
•Protection as specified by customers
•Motor charge type and Manual charge type
•Option:CTD(Capacitor Trip Device), OCR

10
Outer assembly(Non-Extensible)

RPS (2LBS + 1Fuse-switch)

❶
❾

❿
❸

⑮ ❼

⑯ ⑰

❶ LBS operation part ❼ Cable clamp ⑬ Fuse strike link

❷ Chamber ❽ Nameplate ⑭ 200A bushing
LBS LBS LBS
❸ Control connector ❾ Gas pressure gauge ⑮ Straight connector
VD Fuse VD ❹ Fixing bolt for cover ❿ Voltage detector ⑯ Earth lug
❺ 630A bushing ⑪ Fuse holder Body ⑰ Earth busbar
❻ Elbow connector ⑫ Fuse holder cap ⑱ Lift lug

11
Ring Main Units
Outer assembly(Extensible)

RPF (Fuse-switch)

⑲ ❶

❺
⑭

⑫
❹

⑬ ⑪

❽ ❻

❶ 630A bushing for connector ❽ Earth connection hole ⑮ Pressure switch(option)

❷ Chamber ❾ Gas pressure gauge ⑯ Nameplate
S LBS
❸ Fuse holder body ❿ Control connector ⑰ Fixing bolt for cover
❹ 200A bushing ⑪ Cable clamp ⑱ Earthing busbar
Fuse ❺ Operating mechanism ⑫ Fuse holder cap ⑲ Lift lug
❻ Straight connector(Option) ⑬ Fuse strike link
❼ Upper side cover ⑭ CTD(option)

12
RPL (Ring switch)

❶
⑭

❽
❾

❿ ❷

❻ ❺

❶ 630A bushing for connector ❻ Earth connection Hole ⑪ Gas pressure gauge
❷ 600A bushing ❼ Upper side cover ⑫ Fixing bolt for cover
LBS
❸ Chamber ❽ Operation mechanism ⑬ Earthing busbar
❹ Elbow connection (option) ❾ Nameplate ⑭ Lift lug
VD
❺ Cable clamp ❿ Voltage detector

13
Ring Main Units
Outer assembly(Extensible)

RVB (Circuit breaker)

❽ ❾

❹
❷

❶ 630A bushing for connector ❻ Gas pressure switch (Option) ⑪ Voltage detector
Trip ❷ 630A bushing ❼ Upper side cover ⑫ Gas pressure gauge
VCB
❸ Chamber ❽ Operation mechanism ⑬ CT
OC ❹ Elbow connection (Option) ❾ Gas filling valve
2×CT
* ❺ Cable clamp ❿ Nameplate

Note) *: Option

14
RBR (Bus rising)

⑫ ❻

❼ ❸

❹ ❺

❶ 630A bushing for connector ❺ Earthing busbar ❾ Voltage detector

❷ 630A bushing ❻ Upper side cover ❿ Cable clamp
❸ Chamber ❼ Gas pressure gauge ⑪ Fixing bolt for cover
❹ Elbow connection (Option) ❽ Nameplate ⑫ Lift lug

VD

15
Ring Main Units
Cable termination

Ring switch / Circuit breaker (ANSI/IEEE Std. 386)

These connectors are designed for easy installation on extruded shield cable or metallic tape shielded cab. The connector
range is from 1/0 to 1000 kcmil for aluminum and copper conductors with insulation diam from o.640" to 1.935".

❽
❻ ❼ ❿ ❸ ❾
❺

❶ Stress relief adapter ❹ Grounding eye ❽ Interference fit

Molded rubber adapter is sized to the cable insulation and Hole provides a convenient point to connect a ground wire Molded insulating peroxide-cured EPDM exerts uniform
provides stress relief for the terminated shield. The radial to the molded conduction shield, placing the molded shield con-centric-pressure on insulation of mating parts to
pressure exerted on the cable shield by the stress surface. at ground potential. provide required creep-path length and watermeal.
Suitable for installation on both extruded-surface. Suitable
for installation on both extruded-shield cable and tape-type
❺ Wrap-around conductive inserts ❾ Apparatus bushing
shield cable. Inner shield of molded conductive peroxide-cured EPDM
precludes subjecting entrapped air to electrical stress. A Epoxy product normally supplied on manufacturers
❷ Spade terminal patented ELASTIMOLD feature. equipment. Can be welded or clamped to the apparatus.

Semi-permanent, crimped-bolted connector sized for the ❻ Voltage test point cap ❿ Threaded stud
specific conductor. Crimped on with standard tools and Molded conduction rubber cap fits over the test point and
dies, Also used in the 650Y splice. A removable threaded stud is included with every 655LR
onto the connector housing.
and K655LR.
❸ Molded conductive shield ❼ Voltage test point
Outer jacket of 1/8 think molded conduction peroxide- The 1 hex nut located on the top of the insulation plug
cured EPDM provides a virtually in destructible ground allows the circuit to be tested without disturbing the
shield for true dead-front construction. A patented ELASTI- connection. The nut is fully insulated from the conductor
and pick up capacitance voltage. A torque wrench with a 1
MOLD feature.
hex socket attachment is required during installation.

Fuse-switch
The straight receptacles are fully-shield, fully-submersible and separable insulated connectors. These will accommodate
conductor sizes of No. 4 solid through 4/0 stranded and cable insulation diameters from 0.495" through 0.985".
Molded conductive insert
Conductor contact

Bushing Bail
for load tip
side
Wire
Straight receptacle housing

Grounding eye

Straight
receptacle Bail
Nut
Cable
"A"

Bail plate

16
Cable termination

1 way 1 way with SA 2 way 2 way with SA

24kV cable termination selection table

Company Voltage class Current Description Model number
K655BLR
Power distribution K655BIP
Elastmold 600A
24kV connectors K650CP
(PYUNGIL Co., Ltd)
K650ETP
200A Straight receptacles K151SR
EUROMOLD 24kV 600A Tee connector K400TE
5815-S
5815-T
3M 24kV 600A Modular splicing kit 5815-D
5815-E
5815-B
DT625, 635

Cooper power DIP625AS, 635AS

24kV 600A Bol-T connector
system CC6A-U
CA625, 635
*SA: Surge Arrestor

17
Ring Main Units
Pannel connection

Electrical connection with special connectors

Plug

Clamping bolt
Washer
Spacer Cross connector

Mold cable
End connector

Bushing

Mechanical Joint Panel to Panel

18
Accessaries

Fuse
Features
1. The LS HRC Power Fuses belong to the PRIME MEC
series.
It interrupts high currents before the peak value and
therefore cuts down the required withstand capacity of
the associated equipment on the electric system.
2. Though small in size, it has a high breaking capacity and
its enclosed type is suitable for use inside of the panel
board.
3. PRIME-MEC fuses are equipped with striker pins for
trip indicators as well as for inflicting impulse to trip
link of related load break switches.

Selection of fuses: According to IEC 60787(24kV)

Power Fuse rated current(A) Transformer rating capacity (kVA)
5 36-75
10 75-157
20 172-358
30 258-538
40 464-965
50 598-1246
63 745-1554
Note) Please ask fuse maker for optimum selection of fuses.

Power fuse characteristic curve

Cut-off characteristic Pre-arcing time-current characteristics

1000 1000
800 800
600 600 5A 200A

400 400 10A 160A

200 200 20A 125A

100 100 30A 100A

80 200A 80
60 60 40A 75A
160A
40 40
125A 50A 63A
Cut-off current(peak value:kA) →

100A 20
20
75A
Operating time(sec.) →

10 63A 10
8 8
6 50A 6
4 40A 4

30A
2 2
20A
1 10A 1
0.8 0.8
5A 0.6
0.6
0.4 0.4

0.2 0.2

0.1 0.1
0.08 0.08
0.06 0.06

0.04 0.04

0.02 0.02

0.01 0.01
20

40
60
80

400

800
200

600

4000
100

2000
4

6000
8000
2

1000

10000
10
6
0.1

0.2

2
0.02

0.04
0.06
0.08

0.4
0.6
0.8

6
8
10

100
40
4

20

Prospective breaking current(rms:kA) → Prospective breaking current (rms:A) →

19
Ring Main Units
Accessaries

Vacuum Interrupter
In the closed position, normal current flows
through the interrupter. When a fault occurs
and interruption is required, the contacts are
quickly separated.
Current path
The arc drawn between the surfaces of
contacts is rapidly moved around the slotted
contact surface by self induced magnetic
Driving force
effects, preventing gross contact erosion and
on the high the formation of hot spot on the surface.
current ARC The arc burns in an ionized metal vapor,
which condenses on the surrounding metal
ARC
shield. At current zero the arc extinguishes
and vapor production ceases.
The metal vapor plasma is very rapidly
dispersed, cooled, recombined, and deionized,
and the metal vapor products are quickly
condensed so that the contacts withstand the
Figure 1. Current flow and driving
force on arc for spiral
transient recovery voltage.
contact

(ⅰ) Weld (ⅰ) Contact jets (ⅰ) Arc instability

(ⅱ) Bridge explosion (ⅱ) Shield involvement (ⅱ) Interruption

High current arc mode

Arc initiation Current
zero

Fault
current

Time (ms) Time (㎲)

Voltage Phenomena
(ⅰ) Arc reignition
(ⅱ) Restrikes
(ⅲ) B. I. L
(ⅳ) AC voltage
withstand

Recovery
voltage

Figure 2. AC arcing and interruption phenomena in vacuum.

20
Relay
GIPAM

•LS Integrated Protection and Metering Device

•Integrating the other panel meter, protection relay, control
switch on GIPAM
•Option
- Transducer function
- Sequence of event
•Special Features
- Simplication of the equipments
- Various display function
- Various protection function & easy event analysis
- Data communication function
- High reliability with self-diagnosis function

DPR

•LS high performance Digital Protection Relay

•Various unit types
OCR, OCR/OCGR, OVR(UVR), OVR/UVR, OVGR, SGR
•Effective mutual back-up protecting. Setting range of time
and current is wide and subdivided.
•Fault Recording function and SOE(Sequence of Event)
function provides quickly accurate information to user that is
used in analyzing causes of fault.
•High speed data communication by I-NET communication
method, completely interface with SCADA

Devices
Protection/monitoring Code
GIPAM DPR-011S DPR-111S DPR-211S DPR-311S DPR-411S DPR-511S
Three-phase overcurrent 50-51 ○ ○ ○
Zero-sequence overcurrent 50N-51N ○ ○
Selective zero-sequence overcurrent 67G ○ ○
Overvoltage 59 ○ ○ ○
Undervoltage 27 ○ ○ ○
Zero-sequence overvoltage 59N ○ ○
Measuring ○

21
Ring Main Units
Accessaries

Current transformer
Max. system voltage kV 0.6

Primary current A 100

Secondary current A 5

Rated burden VA 10

Accuracy class 10P10

Short time current kA/1s 16

Rated frequency Hz 60

Polarity Subtractive

Surge arrester
The 273ESA Elbow Arrester is combined with a loadbreak elbow connector interface.

Surge arrester Stud bolt

Bushing

Bushing insert
Probe Spade terminal Shelded elbow

Grounding eye
Cable adapter

Ground lead Cable

Protective characteristics
Note1)
Duty cycle Maximum discharge voltage (kV crest) F.O.W. protective
MCOV
rating ×20 microsecond current wave
8× level
(kVrms)
(kVrms) 1.5kV 3kV 5kV 10kV 20kV (kV crest) Note2)

25kV 8.4 10 30.5 32.5 34.5 38.5 43.5 38.5

class 10.2 12 40.0 42.5 45.0 50.0 56.5 50.0
12.7 15 48.0 51.0 54.0 60.0 68.0 60.0
15.3 18 56.5 60.0 64.0 71.0 80.5 71.0
17.0 21 65.5 69.5 74.0 82.5 93.0 82.5

Note) 1. MCOV- Maximum Continuous Operation Voltage.

2. The front of wave (FOW) protective level is the maximum discharge for a 5kA impulse current wave producing a voltage
wave cresting in 0.5 microseconds.

22
CTD (Condenser trip device)

(For discharge)
AC input DC output
CTD is built as standard in the contactor with
AC control of instantaneous excitation so that
the contactor can be tripped within 30 seconds in
the event of an electricity failure. The automatic
Control circuit diagram
trip circuit in the event of an electricity failure is
to be built by a customer.
Rating Description
Type CTD-100 CTD-200

Rated input voltage(V) AC 100/110 AC 200/220

Frequency(Hz) 50/60 50/60

Rated impulse
140/155 280/310
voltage(V)
Charging time Within 5 sec. Within 5 sec.
Trip command
Max. 30 sec. Max. 30 sec.
possible time Terminal
Input voltage range 85%~110% 85%~110%
Capacitor rating(μ
F) 400 160

Closing coil (C) Shunt coil (TC)

The coil operated only when the power is applied When the VCB is 'ON' position, even though the control
continuously over 45ms. It has built-in electrically anti- power of a shunt coil is 'OFF', the VCB maintains the 'ON'
pumping circuit. position.

Rated voltage Rated current (A) Rated voltage Rated current (A)

DC 24V 10 DC 24V 10
DC 110V 2.5 DC 110V 2.5
Note 1) Range of the normal operating voltage: 85~110% Note 1) Range of the normal operating voltage: 70~110%
2) DC 24V is the underdeveloped rating. 2) DC 24V is the underdeveloped rating.

GAS pressure gauge Control connector Voltage detector

Screw type

Plug in type
07
08
09
10
11
01
02
03
04
05

06
12
13
14

17
18
19

23
Ring Main Units
Installation

R = 10D

D : Cable diameter

RPS RVB + RPL + RBR

4- 18×38 12-Ø16
Mounting hole 77 1348 77 Mounting hole
120

607
626

466
120

61.5
102 327 524 327 102 90.5 377 144 315 144 315
40

RPF RPL, RBR RVB

6-Ø18 4-Ø18
Mounting hole Mounting hole 4-Ø16
Mounting hole
607
607
607
303.5

70.5 315
61.5
61.5

70.5 315
61.5

70.5 470

24
Technical data

Installation type Indoor type

Rated voltage up to kV 24

Rated current A 630 A

Rated current (RVB,RPF) A 200

Rated power frequency Hz 50 / 60

Rated short current kA/1s 16

Rated making current kA 41.6

Power frequency withstand voltage kV 50

Rated impulse withstand voltage kV 125

Operation type electromotion / manual

Operating voltage V DC 110

Operating voltage (CTD Input) V AC 110

Insulation material SF6 Gas

Rated filling pressure (20 °C) Mpa. 0.034 (5 psi.G)

Minimum operating pressure (20 °C) Mpa. 0.014 (2 psi.G)

Transfer current (RPF) A 800

Electrical life E3

Electrical life (RVB) E1 , C1

Mechanical life M1

Standard IEC 60265-1, IEC 60420

Standard (RVB) IEC 62271-100

25
Ring Main Units
Quality assurance

Certified quality: KEMA, ISO 9001, ISO 14001

LS Industrial systems has integrated a functional organization into each of its units, the main
purpose of which is to check quality and ensure the adherence to standards.

Routine quality check

While producing Tri-MEC RMU, various routine tests are taken for product capacity, which
testing items are as shown follows.
•Filling pressure check
•Tightness check
•Opening and closing speed measurement
•Dielectric check
•Contact resistance check

Seismic tests
Application standard: JEAG5003-1999

26
 Norminals
Test Structural
excitation level(g) Direction Freq.(Hz) Waveforms Duration(S) Operability
category integrity
X/Y/Z
Resonance X
search 0.1/0.1/0.1 Y 0.5-30 Random 328 N/A N/A
test Z
Real Kobe
earthquake 0.3/0.3/0.15 XYZ Earth- 82 OK OK
test quake
0.3/0/0 X OK OK
0.3/0/0.15 XZ OK OK
5
0/0.3/0 Y OK OK
0/0.3/0.15 YZ OK OK
0.3/0/0 X OK OK
Sine 30 0.3/0/0.15 XZ Sine 30 OK OK
waves test 10
0/0.3/0 Y Wave Waves OK OK
0/0.3/0.15 YZ OK OK
0.3/0/0 X OK OK
37.8
0.3/0/0.15 XZ OK OK
0/0.3/0 Y OK OK
12.2
0/0.3/0.15 YZ OK OK
Resonance X
search 0.1/0.1/0.1 Y 0.5-30 Random 328 N/A N/A
test Z

Ordering Information

LGS R M 24 6 12 RT D

LS Ring Main Unit Rated Current Cable connection type

2 200A D Dead Break Type
Switch type 6 630A Dead Break &
M
RPF, RPL, RPS, Plug-in Type
R Rated impulse
RVB, RBR
withstand voltage Switch and circuit type
Operating type 12 125kV BIL 21 2L-1F (RPS)
M Automatic 1L 1 LBS (RPL)
B Manual 1Fuse-Combination
1F
LBS (RPF)
Rated Voltage 1R Bus Rising (RVR)
24 25.8(24)kV 1V 1VCB (RVB)
21V 2L-1VCB (RVS)

27
 Leader in Electrics & Automation

� For your safety, please read user's manual thoroughly before operating.
� Contact the nearest authorized service facility for examination, repair, or adjustment.
� Please contact qualified service technician when you need maintenance.
Do not disassemble or repair by yourself!
Safety Instructions � Any maintenance and inspection shall be performed by the personnel having expertise concerned.

www.lsis.biz

� HEAD OFFICE � Global Network

�LS Industrial Systems (Middle East) FZE �
�Dubai, U.A.E.
Yonsei Jaedan Severance Bldg., 84-11, Namdaemunno 5ga, Address: P.O.Box-114216, API World Tower, 303B, Sheikhe Zayed Road, Dubai, U.A.E.
Jung-gu, Seoul, 100-753, Korea Tel: 971-4-332-8289 Fax: 971-4-332-9444 e-mail: [email protected]

Tel. (82-2)2034-4870 �Dalian LS Industrial Systems Co., Ltd. �

�Dalian, China
Address: No.15, Liaohexi 3-Road, Economic and Technical Development zone, Dalian 116600, China
Fax. (82-2)2034-4713 Tel: 86-411-8273-7777 Fax: 86-411-8730-7560 e-mail: [email protected]
�LS Industrial Systems (Wuxi) Co., Ltd. �
�Wuxi, china
Address: 102-A , National High & New Tech Industrial Development Area, Wuxi, Jiangsu,214028, P.R.China
Tel: 86-510-8534-6666 Fax: 86-510-522-4078 e-mail: [email protected]
� CHEONG-JU PLANT �LS-VINA Industrial Systems Co., Ltd. �
�Hanoi, Vietnam
Cheong-Ju Plant #1, Song Jung Dong, Hung Duk Ku, Address: Nguyen Khe - Dong Anh - Ha Noi - Viet Nam
Tel: 84-4-882-0222 Fax: 84-4-882-0220 e-mail: [email protected]
Cheong Ju, 361-720, Korea
�LS Industrial Systems Tokyo Office �
�Tokyo, Japan
Address: 16FL, Higashi-Kan, Akasaka Twin Tower 17-22, 2-chome, Akasaka, Minato-ku Tokyo 107-8470, Japan
Tel: 81-3-3582-9128 Fax: 81-3-3582-2667 e-mail: [email protected]
�LS Industrial Systems Shanghai Office �
�Shanghai, China
Address: Room E-G, 12th Floor Huamin Empire Plaza, No.726, West Yan'an Road Shanghai 200050, P.R. China
Tel: 86-21-5237-9977 (609) Fax: 89-21-5237-7191 e-mail: [email protected]
�LS Industrial Systems Beijing Office � �Beijing, China
Address: B-Tower 17FL.Beijing Global Trade Center B/D. No.36, BeiSanHuanDong-Lu, DongCheng-District,
Beijing 100013, P.R. China
Tel: 86-10-5825-6025,7 Fax: 86-10-5825-6026 e-mail: [email protected]
�LS Industrial Systems Guangzhou Office �
�Guangzhou, China
Address: Room 1403,14F,New Poly Tower,2 Zhongshan Liu Road,Guangzhou, P.R. China
Tel: 86-20-8326-6764 Fax: 86-20-8326-6287 e-mail: [email protected]
�LS Industrial Systems Chengdu Office �
�Chengdu, China
Address: 12Floor, Guodong Buiding, No52 Jindun Road Chengdu, 610041, P.R. China
Tel: 86-28-8612-9151 Fax: 86-28-8612-9236 e-mail: [email protected]
�LS Industrial Systems Qingdao Office �
�Qingdao, China
Address: 7B40,Haixin Guangchang Shenye Building B, No.9, Shandong Road Qingdao 26600, P.R. China
Specifications in this catalog are subject to change without notice due to Tel: 86-532-8501-6568 Fax: 86-532-583-3793 e-mail: [email protected]
continuous product development and improvement.

2008. 01 Ring Main Units(E) 2003. 06/(06) 2008. 01 Printed in Korea STAFF