SI B 84 01 02 July 2006

Phone, Navigation Systems Technical Service

This Service Information Bulletin supersedes S.I. B84 01 02 dated March 2006.

designates changes to this revision

SUBJECT
Navigation System Operating Software

MODEL
E38 (7 Series)

E39 (5 Series)

E46 (3 Series)

E53 (X5)

E83 (X3)

E85, E86 (Z4)

E65, E66 (7 Series)

SITUATION
With the introduction of navigation system operating software V27.1, there are currently 2 valid versions of
navigation software.

1. Navigation system operating software V17.1 is used on MK III systems without "Split Screen".

2. Navigation system operating software V27.1 is used on MK I, MK II, all other MK III navigation
systems, MK IV DVD navigation systems on I-Bus vehicles, NAVI01, NAVI02 and NAVI03.

CORRECTION
Navigation system operating software should be updated under the following circumstances:

The Navigation computer has been replaced.

Progman prompts during programming/coding the navigation software to be updated.

If instructed by a Service Information Bulletin or the Technical Hotline.

NEW FEATURES INTRODUCED WITH NAVIGATION SOFTWARE V27.1

There are no new features relevant for US vehicles on that Navigation SW version.

NEW FEATURES INTRODUCED WITH NAVIGATION SOFTWARE V27

Only E46 (3 Series), E53 (X5), E83 (X3), E85 (Z4) with DVD Navigation system

Disclaimer screen disappears automatically after 8 second

City/Town names displayed in the map

E46 (3 Series), E53 (X5), E83 (X3), E85 (Z4) with DVD Navigation system
E65/E66 (7 Series) DVD NAVI03 (from03/05)

Destination input when Country (UNITED STATES or CANADA) is selected via:

ZIP code

City name

Destination input when an US State or a Canadian Province is selected via:

Street name

City name

ZIP code

Note: Only in conjunction with NAVTEQ DVD road Map 2006-2

POI (Point of Interest) icons and "City Center" icons are displayed together

Travel Information (TMC) is no longer displayed (is inactive and not selectable)

Entries in "Address Book/Last Destination" displayed as:

City name, Street name (Destination entry via City name)

ZIP code, City name, Street name (Destination entry via ZIP code)

Product Information

Legal Disclaimer for usage of the Navigation system and the data on the NAVTEQ road maps

How to report missing or incorrect data feedback to NAVTEQ:

Website: www.navteq.com/bmwmaps

Phone: 1-888-navteq9 (628-8379)

Email: [email protected]

E83 (X3) and E85 (Z4) with flap display

Software fix for the flap issues (opening/closing)

FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V26

The actual location is shown as an arrow in a circle

The destination is marked with a checkered flag

Map Positioning in "Travel Direction" can now be selected in scales up to 100 mls

Disable POI icons is now selectable on I-Bus DVD NAV systems in:

General Destinations
 Travel Information

The following functions are now selectable on E65/E66 with NAVI03 (from 03/2005):

Hide Map Icons

General Destinations and Travel Information

After loading NAV SW V27.1, the vehicle must be driven to ensure the proper function of the
Navigation system and the correct displaying (Interstate Icons)

CHECKING SOFTWARE VERSION

MK I Systems

The software version is shown in the top right corner of the "setting" screen. The software/hardware version is
displayed as "1-1/80". The numbers have the following meanings: first digit 1 - is a 1st generation navigation
system (MK I); second digit 1 - is a 1st device variant (top navigation – MK Ic color screen); the last two digits
80 - are the software version of the graphic component (8.0).

MK II Systems

The software version is shown in the top right corner of the "setting" screen. The software/hardware version is
displayed as "2-1/81". The numbers have the following meanings: first digit 2 - is a 2nd generation navigation
system (MK II); second digit 1 - is a 1st device variant (top navigation – MK IIc color screen); the last two digits
81 - are the software version of the graphic component (8.1).

MK III Systems

The software version is shown in the top right corner of the "setting" screen. The software/hardware version is
displayed as "3-1/63" or "3-2/63"(MK III with split screen). The numbers have the following meanings: first
digit 3 - is a 3rd generation navigation system (MK III); second digit 1 - is a 1st device variant (top navigation –
MK IIIc color screen), or 2 – is a 2nd device variant (radio navigation – MK IIIm monochrome display); the last
two digits 63 - are the software version of the graphic component (6.3).

DVD navigation system for I-Bus vehicles

The software version is shown in the top right corner of the "setting" screen. The software/hardware version is
displayed as "4-1/71". The numbers have the following meanings: first digit 4 - is a 4th generation navigation
system (DVD); second digit 1 - is a 1st device variant (top navigation – DVD color screen); the last two digits 71
- are the software version of the graphic component (7.1).

E65/E66 Systems

Enter the Service Mode of the Control Display

Select "MOST Devices"

Scroll down and select "Navigation"

Scroll down a few pages until "Software Version" is displayed

Software Version for CD navigation (NAVI01) should be 7.3.2 (I-level E065-05-03-810.2)

Software Version for DVD navigation (NAVI02) should be 8.4.4 (I-level E065-05-03-800.2)
 Software Version for DVD navigation (NAVI03) should be 9.3.0C (I-level E065-06-03-500)

Current Software Versions

Software
Application
version
8.0 MK I - E39/E38 (up to 9/97)
8.1 MK II - E39/E38 (from 9/97), E46, X5

9.0 MK II - Radio Navigation – E52 (Z8)

5.1 MK III Radio Navigation – E52 (Z8) from 09/00
MK III w/o Split Screen -E46 from 06/00, E39/E38 from 09/00, E53 from
3.1*
10/00

6.3 MK III with Split Screen

7.1 MK IV DVD Navigation
7.3.2 E65/E66 NAVI01 (CD-drive)
8.4.4 E65/E66 NAVI02 (DVD-drive)
9.3.0C E65/E66 NAVI03 (DVD-drive)
*Included in Navigation software CD V17.1

LOADING SOFTWARE (ALL EXCEPT E65/E66)

For MK I, MK II, MK III, and DVD NAV systems (except E65/E66) use the following software loading
instructions:

1. Turn ignition to position 1 (terminal R).

Do not cycle the key or perform diagnosis while installing the new software. Make sure that the power supply is
stable, i.e. do not switch on any electrical loads.

2. Activate "GPS-Navigation" and acknowledge the screen disclaimer by pushing the rotary knob.

3. Remove the map CD from the Navigation computer by pressing "eject" button.

4. Insert the Navigation Software CD (V17.1 P/N 01 59 9 789 299 index "x" for MK III without split
screen, V27.1 P/N 01 59 0 141 891 index "t" for all other versions).

5. Mark I System (up to 9/97 production):

After a few seconds, the BMW roundel will appear on the board monitor and will be "filled in" clockwise to
show the progress of loading (approx. 4-6 minutes).

Mark II System (from 9/97 production),

Mark III System (E46 from 06/00 and E38/E39/E52 from 09/00 production),

DVD navigation system (E46, E39, E52 from 09/02 and E53, E85 from 10/02 production):
After a few seconds, a menu of notes on loading procedure and "progress" bar appear on the board monitor.

When the loading process has been completed, the message "Software has been successfully loaded" is displayed.

6. Remove the operating software CD and confirm the end of the loading process by pressing the rotary
push-button on the board monitor. "OK" appears in the display.

7. Drive the vehicle before delivering to the customer to ensure the correct function and displaying
(Interstate Icons) of the Navigation system.

LOADING SOFTWARE (E65/E66 ONLY)

When programming any E65/E66 using Progman V21 or higher, you will be prompted by the Progman
screen that "BMW Navigation CD Version 27" must be loaded prior to programming the vehicle.

Note: Connect an approved battery charger before loading software.

1. Turn on ignition to Terminal R or 15

2. Enter the Navigation Menu.

3. Remove the NAVTEQ road map CD/DVD

4. Insert the Navigation Operating Software CD V27.1 (P/N 01 59 0 141 891 index "t") into the
navigation computer and use Progman V22 or a more recent version for NAVI03 (DVD navigation).

5. Select "Yes" with the Controller to install software.

6. The software will then load in two steps, takes approximately 10-15 minutes.

7. Do not touch the iDrive while the software is loading.

8. When the installation is finished the CD will be ejected. The message "Installation Successful, Remove
Software loading CD and press OK" will appear. At this point select "OK" with the Controller.

9. The Navigation system will then "reinitialize".

10. When prompted, insert NAVTEQ road map CD/DVD.

11. Refer to SI B09 05 01 (Coding, Individualization and Programming) for any necessary coding and
programming. Note that Progman will automatically reprogram all programmable control units that do not
have the latest software.

12. Drive the vehicle before delivering to the customer to approve the correct function and displaying
(Interstate Icons) of the Navigation system.

NAVIGATION COMPUTER REPLACEMENT MK III

When replacing a defective MK III computer, a configuration signal is required to allow the new computer
to load the correct software for its respective application. This is generated by using DIS coding program
"Coding ZCS C46.0" or higher and Navigation System operating software CD V 17.1 or V27.1.

1. Connect DIS/GT1 tester to vehicle

2. From the DIS Coding/Programming select "1 ZCS Coding"

 3. Select appropriate engineering series (E38, E39, etc.)

4. Select "4 conversion"

5. Select "3 IKE/Kombi"

6. Select "2 Language"

7. At prompt "Is the CD-ROM present?" – select "Yes", but do not insert Navigation CD into the Nav
Computer yet!

8. First select the main language and then an additional language (the choices are: English, French, Italian,
Spanish, German)

9. NOTE: The announcer's voice gender (male or female) can't be selected anymore.

MK I, MK II & MK III: Only male.

MK IV (DVD NAV), NAVI01, NAVI02 & NAVI03: Only female

10. After activation of the automatic coding, the DIS tester tells you to follow the instructions on the monitor
for Navigation CD installation

11. Place the Navigation CD into the navigation computer CD drive

Important: Do not switch ignition OFF during software loading procedure

12. Once loading has been completed, remove the CD and then confirm completion by pressing the rotary
push-button on the monitor

13. Turn ignition OFF for 10 seconds, then turn it ON and conduct a functional check

14. After this step has been finished, encode the Navigation computer in the regular manner using the path "1
Recoding"

TROUBLESHOOTING HINTS
The following problems may occur during the software loading procedure:

The message "CD defective" appears on the display screen.

The message "Fault during programming" appears on the display screen.

The message "The system is restarting" appears on the display screen.

The installation process has stopped and the display screen is blank and the power LED on the navigation
computer is off. The CD will not eject.

These complaints are usually the result of a faulty Navigation Operating software CD.

For points 1-3 for error messages that appear on the display screen, check for the correct software version
and try loading a new Navigation CD.

For a CD that will not eject from the Navigation computer follow the procedure below:

1. Remove the Navigation computer.

 2. Unplug the voltage supply (blue connector).

3. Reconnect the voltage supply and immediately press the eject button repeatedly until the CD in the
drive is ejected.

4. Insert a new Navigation CD and restart the installation process.

PARTS INFORMATION
Part Number Description
01 59 9 789 299 Navigation Software CD V17.1 Index "x"
01 59 0 141 891 Navigation Software CD V27.1 Index "t"
Copies of the CD V27.1 will be shipped to every BMW Center through the Automatic Tool Shipment
Program.

WARRANTY INFORMATION
Updating the vehicle at customer request is not covered under warranty.

[ Copyright © 2006 BMW of North America, LLC ]