FEATURES

INSTRUCTION MANUAL • It displays real time battery voltage, discharged capacity and discharge current.
#PC-022-001 • It can test battery capacity that helps select batteries with desired capacity.
• It saves time when user wishes to store their large capacity batteries.
INTRODUCTION
• It helps activate the best performance of your batteries for competition.
Thank you for choosing the PULSETEC Battery Discharger & Analyzer B-GEN 200. The B-GEN 200
is a powerful discharging device that allows the user to discharge a battery at up to 30 amps or 200
FEATURES
watts and also measures and compares the performance of batteries. B-GEN 200 allows for the precise
1- BATTERY CONNECTION 2- POWER ON
measurement of battery capacity and takes the guesswork out of choosing the best battery for your
application. Press the Dial once to power
The B-GEN 200 is much more than a simple battery discharger or a battery load tester. It will test virtually ON the discharger, the LED
any type or size of battery, any chemistry or number of cells, up to 35 volts. (V/mAh) will blink with beep
sound.
The B-GEN 200 is ruggedly built and uses XT60 connector for battery connection. It is small with a high
performance cooling system. Digital LED indicates battery voltage, discharge capacity and discharge
current.

3- SELECT CUT-OFF VOLTAGE AND DISCHARGE CURRENT

The LED(V/mAh) shows the current battery voltage.

Heat Sink

ROTARY DIAL
for Setting Cut-off Voltage
Discharging Current
Start/Stop Button
XT-60 Battery Port Use the Dial button to modify the discharge current
DATA Link Current Display (A)
4- S
 TART DISCHARGING PROCESS
Battery Voltage / Capacity Press and hold Dial button for 2 seconds, the discharger will start
Display (mAh) with beep sound.
During the discharging process, the digital LED(V/mAh) will alternate
the display of battery voltage and discharging capacity.
SPECIFICATIONS
5- STOP DISCHARGING PROCESS
Accepted Voltage Range : . . . . . . . 5,40 - 35,00V Voltage Display Accuracy: . . . . . 5.4-10V ±60mV During the discharging process, Press the dial once to stop the
discharging process, the digital LED(A) shows “Stop”.
Low Voltage Alert :. . . . . . . . . . . . . . . . . . . <5,2V 10-20V ±120mV
High Voltage Alert :. . . . . . . . . . . . . . . . . . . . >35V 20-35V ±160mV 5- PROCESS FINISHED
When the discharging process has finished, the discharger will beep
Max Discharge Power :. . . . . . . . . . . . . . . . 200W Capacity Display Accuracy :. . . . . . . . . . . . . ±3%
5 times, and the LED(V/mAh) will show battery voltage and discharge
Discharge Current range : . . . . . . 0,01A - 30,00A Dimension :. . . . . . . . . . . . . . . . . 136x105x96mm capacity respectively.
Current consumption in Sleep Mode . . . . <100uA Weight :. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 858g
Standby Current :. . . . . . . . . . . . . . . . . . . <35mA
Current Display Accuracy: . . 0.01-10.00A ±60mA
10.00-30.00A ±2%

1 2
 Battery No. of Min. Cut-Off
Voltage
Min. Discharge Current (A) Max. Discharge Current (A) PC SOFTWARE
Type Cell Voltage Discharging power: 200W Discharging power: 200W
• PC software supplied with the B-GEN 200 is easy to use, intuitive.
2S 6.0 8.40 23.80 30.00 • There are two discharge mode: Constant Power and Constant
3S 9.0 12.60 15.87 22.20 Current.
4S 12.0 16.80 11.90 16.60
• The software can automatic sensing of battery cell count and
recommends a minimum safe discharge voltage.
LiPo 5S 15.0 21.00 9.52 13.30 • Discharge tests may be viewed in Amp Hours, Watt Hours or
6S 18.0 25.20 7.93 11.10 Minutes.
7S 21.0 29.40 6.80 9.52
• Results can be graphed as Voltage vs. Amp hours, Watt hours,
Minutes.
8S 24.0 33.60 5.95 8.33
2S 6.2 8.70 22.98 30.00
SAFETY NOTE
3S 9.3 13.05 15.32 21.50
• Never discharge a battery below its recommended cut-off voltage. Over-discharge may damage
4S 12.4 17.40 11.49 16.12 battery and cause FIRE or EXPLOSION.
LiHV 5S 15.5 21.75 9.19 12.90 • Never discharge a battery at a higher discharge rate than it is designed for.
6S 18.6 26.10 7.66 10.75
• Never leave the discharger unattended when it is connected to battery. If any malfunction is found,
TERMINATE THE PROCESS AT ONCE.
7S 21.7 30.45 6.56 9.21 • Place the discharger and battery on a non-flammable surface, and keep away from inflammables.

TCRP INTERNATIONAL LLC Ltd • 21B Moskovska Street. Floor 3 • 1000 Sofia - Bulgaria • [email protected] - www.pulsetec.eu
8S 24.8 34.80 5.74 8.06 • Never discharge swollen, leaky, or damaged batteries.
• Batteries shall be discharged within a room temperature range of 10-40°C.
6S 5.4 9.00 22.22 30.00
• Disconnect the battery and discharger once discharging has finished.
7S 6.3 10.50 19.04 30.00 • Recharge batteries immediately with an appropriate battery charger after discharge process is
8S 7.2 12.00 16.66 27.77 completed. Some battery types do not like to remain discharged for extended periods of time.
9S 8.1 13.50 14.81 24.69 WARRANTY AND SERVICE
10S 9.0 15.00 13.33 22.22 We guarantee this product to be free of manufacturing and assembly defects for a period of 12 or 24 months from the
time of purchase. The warranty only applies to material or operational defects, which are present at the time of purchase.
11S 9.9 16.50 12.12 20.20
During that period, we will repair or replace free of service charge for products deemed defective due to those causes.
12S 10.8 18.00 11.11 18.51 You will be required to produce proof of purchase (invoice or receipt). This warranty is not valid for any damage or
subsequent damage arising as a result of misuse, modification or as a result of failure to observe the procedures outlined
NiMH 13S 11.7 19.50 10.25 17.09
in this manual.
14S 12.6 21.00 9.52 15.87
DURATION OF VALIDITY
15S 13.5 22.50 8.88 14.81
The claim period is 24 months from the date of purchase of the product by the consumer from a dealer in the European
16S 14.4 24.00 8.33 13.88 Community (EC) counted from the date of purchase. The claim period is 12 months from the date of purchase of the
17S 15.3 25.50 7.84 13.07 product by the consumer from a dealer outside the European Community (EC) counted from the date of purchase. If a
defect arises after the end of the claim period, or if evidence or documents required according to this declaration in order
18S 16.2 27.00 7.40 12.34 to make the claim valid are not presented until after this period, then the consumer forfeits any rights or claims from this
declaration. The guarantee period is not prolonged by the granting of any claims within the framework of this warranty,
19S 17.1 28.50 7.01 11.69
especially in the case of repair or replacement. The guarantee period also does not restart in such cases.
20S 18.0 30.00 6.66 11.11
WARRANTY EXPIRATION
If we do not acknowledge the validity of a claim based on this declaration within the claim period, all claims based on this
declaration will expire after six months from the time of registering the claim; however this cannot occur prior to the end
ERROR MESSAGE
of the claim period.
When there is an error, digital LED will display the error code :

Over-temperature protection.

Input voltage is too high. This discharger accepts battery voltage from 5.4 to 35V, if
voltage higher than 35V, it will stop working and show error message.

Input voltage is too low. This discharger accepts battery voltage from 5.4 to 35V, if voltage
Download Téléchargez le Manuel Download
lower than 5.4V, it will stop working and show error message. English Manual en Français Deutsche Anleitung

3 4