Scribd
Upload
64 views

2 Main Display Module Initialization - Adjust

Uploaded by

Juan Carlos Inga Vasquez
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
64 views

2 Main Display Module Initialization - Adjust

Uploaded by

Juan Carlos Inga Vasquez
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Service Information System Page 1 of 2

Testing and Adjusting


Caterpillar Monitoring System
Media Number -SENR1394-27 Publication Date -01/07/2019 Date Updated -03/07/2019

i04818112

Main Display Module Initialization - Adjust


SMCS - 7490-025

The initialization is an internal process within the main display module. During the initialization,
the main display module listens to the Cat Data Link and the harness code inputs. From this
information, the module learns about the machine. For example, the module learns that the
information for the engine oil pressure is coming from an engine ECM.

Note: On later model products, the harness code is located within the module software and does
not require this initialization procedure.

Normally, the initialization occurs when the main display module is replaced. Also, the
initialization occurs when there is a change in the harness code. However, when a previously used
main display module is used as a replacement, initialization could be necessary. Faults that cannot
be explained with the Cat Data Link can occur if the main display module is not initialized
correctly. The service person must activate the initialization when the main display module
has been previously used. Initialization is used if the module was taken out of an application
that had the same machine code as the main display module that is to be removed.

Procedure For Initialization


This procedure causes the initialization to occur on any main display module. Initialization
requires that the main display module to be powered up with a valid harness code. The valid
harness code must be different than the harness code when the module was last powered down.
For a list of valid harness codes, see the table for Machine Codes in System Operation, "Harness
Code Mode".

1. Code input configuration.

a. Turn the key start switch to the OFF position.

b. Determine whether the harness code inputs are hard wired in the machine harness or
accessible at a harness code plug. Use the Electrical System Schematic in the Service
Manual for the machine.

Expected Result: There is a harness code plug.

Results:

◾ YES - There is a harness code plug. Remove the harness code plug. Proceed to
3.

◾ NO - The harness code inputs are hard wired in the machine harness. Proceed
to 2.

2. Hard wired procedure.

https://127.0.0.1/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/media... 27/10/2021
Service Information System Page 2 of 2

a. Disconnect the machine harness from the main display module.

b. At the machine harness connector for the main display module, remove the wire for
one of these contacts (3, 6, 12, 16, 22 or 31). Choose a contact that is connected to
ground.

Note: If a ground wire is not available, on any of the mentioned ECM contacts, then
install a jumper wire between contact 2 (ECM ground) and contact 3 and repeat 2.b.

c. With tape, secure the removed connector contact out of the way.

d. Reconnect the machine harness to the main display.

Results:

◾ CONTINUE - Proceed to 3.

3. Reconnection and verification.

a. Turn the disconnect switch and the key start switches to the ON position.

b. Various indicators in the Caterpillar Monitoring System display area will illuminate.
Wait 10 seconds.

c. Turn the key switch to the OFF position.

d. Depending on the previous procedure that was performed, either reinstall the harness
code plug (from "Code input configuration") or reinstall the ground connector contact
(from "Hard wired procedure").

e. Make sure that the main display module successfully completes the self test, see
Testing and Adjusting, "System Self Test".

f. Check the machine code. See System Operation, "Harness Code Mode".

Expected Result: The display module has successfully completed the self test.

Results:

◾ OK - The display module successfully completed the self test. STOP.

◾ NOT OK - The display module did not complete the self test. Exit this
procedure. Determine the cause of the failure and repeat "Initialization". STOP.

Copyright 1993 - 2021 Caterpillar Inc. Wed Oct 27 2021 04:26:25 GMT-0500 (Hora est. Pacífico, Sudamérica)
All Rights Reserved.
Private Network For SIS Licensees.

https://127.0.0.1/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/media... 27/10/2021

You might also like