MOTOR SPEED PRODUCT LINE: Section 1741

STAINLESS STEEL PUMPS Page 1741.1

4197 Series™, 4197-SEP Series™ Issue F

TABLE OF CONTENTS SERIES DESCRIPTION

Related Products........................................................................1 Viking’s Motor Speed Product Line internal gear pumps are
available in capacities up to 75 GPM. These pumps can be
Operating Range.........................................................................1
furnished directly connected to a 50 Hz or 60 Hz motor.
Series Description.......................................................................1
4197 Series™ and 4197-SEP Series™ pumps are designed
Features & Benefits....................................................................2 for foot type horizontal mounting. These pumps are built
Specifications..............................................................................2 for continuous or intermittent duty for such applications
as filtering, circulating, transferring or booster service in
Standard Materials of Construction............................................2 general industrial, petrochemical, and other industries.
Model Number Key.....................................................................3 The 4197-SEP Series™ pumps are specially fit with low
temperature materials suitable for subzero solvent transfer or
Cutaway View & Pump Features................................................3
circulation applications. They are also assembled and tested
Mounting Options........................................................................4 using only food grade liquids.
Dimensions – GG, HJ, HL Sizes.................................................5 Both pump series are furnished as standard with
Dimensions – AS, AK, AL Sizes..................................................5 mechanical seal construction to minimize liquid loss and
for shaft protection. The thrust control provides micrometer
Dimensions – GG, HJ, HL, AS, AK, AL Sizes (D Drive).................6 adjustments for accurate rotor and shaft positioning to help
NPSH Required..........................................................................7 you keep operating with new-pump efficiency through years of
heavy duty service.

RELATED PRODUCTS
Cast Iron, 495 Series™ / Series™ 4195 Series:
Catalog Section 1441
Steel Externals, 493 Series™ / Series™ 4193 Series:
Catalog Section 1341

GG4197

OPERATING RANGE

NOMINAL MAXIMUM TEMPERATURE VISCOSITY

FLOW PRESSURE* RANGE RANGE*
SERIES GPM m3 h PSI Bar °F °C SSU cSt
4197 Series™ 7 - 75 1.8 - 17 200 14 0 to +350 -20 to +175 28 to 25,000 1 to 5,500
4197-SEP Series™ 2 - 75 0.5 - 17 200 14 -95 to +225 -70 to +105 28 to 5,000 1 to 1,100

* 200 PSI (14 BAR) for above 750 SSU (162 cSt), 150 PSI (10 BAR) for 100 to 750 SSU (20 to 162 cSt),
100 PSI (7 BAR) for 38 to 100 SSU (3 to 20 cSt), 75 PSI (5 BAR) for below 38 SSU (3 cSt)

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

 Section 1741 MOTOR SPEED PRODUCT LINE:
Page 1741.2 STAINLESS STEEL PUMPS
Issue F 4197 Series™, 4197-SEP Series™

FEATURES & BENEFITS STANDARD MATERIALS OF

• Ball Bearings Standard CONSTRUCTION
» Pumps are equipped with inner cas­ing ball bearing
installed outside of mechanical seal and a radial thrust Component Standard Material
ball bearing permitting heavy-duty service up to 200 PSI
Casing Stainless Steel, ASTM A743, Grade CF8M
(14 BAR). Bearings are “Sealed for Life”.
Head Stainless Steel, ASTM A743, Grade CF8M
• Integral Over-Pressure Relief Valve Standard
Stainless Steel, ASTM A743, Grade CF8M,
» Permits bypassing of liquid from discharge to suction Rotor
Case Hardened
side of pump. Prevents build up of pressure in dis­charge
line. GG, HJ and HL size valve mounts on pump head. Idler 770 Stainless Steel Alloy
AS, AK and AL size valve mounts on pump casing. Stainless Steel, ASTM A276 Type XM-19
Rotor Shaft
or 316 Condition B
• Mechanical Seal Standard
Hard coated Stainless Steel, ASTM A276 Type
» All 4197 Series™ and 4197-SEP Series™ pumps are Idler Pin
316, Colmonoy #6 Coated
furnished with a positive drive mechanical seal. The
seal is a simple, self-adjusting, non-leak method of shaft Idler Bushing Carbon Graphite
sealing. It is especially suited for handling liquids Pressure
such as alcohols, solvents, etc. Stainless Steel, ASTM A723, Grade CF8M
Relief Valve
• Stainless Steel Pumping Elements Standard
4197 Series™: Stainless Steel, PTFE,
» Internal pumping gears are constructed of Type 316 Mechanical Carbon Graphite & Silicon Carbide
and Type 770 Stainless Steel Alloy. This allows high Seal 4197-SEP Series™: Stainless Steel, Fluorosilicone,
speed, non-galling operation, handling all types of Carbon Graphite & Silicon Carbide
liquids up to 25,000 SSU (5,500 cSt). PPS composite
idlers are also available for thin liquid applications.

SPECIFICATIONS

Standard Ports ③ Nominal Pump Rating (100 SSU & below) ① Maximum ④ Maximum ②⑤ Approximate
Differential Hydrostatic Maximum Shipping Weight
Port Size 60 Hz 50 Hz Pressure* Pressure Temperature with Valve
Model
Number Inches Port Type GPM m3/h RPM GPM m3/h RPM PSIG BAR PSIG BAR °F °C Lbs. Kg.
GG4197
1 10 2.3 8 1.9 20 9
GG4197-SEP1
HJ4197
20 4.5 1750 17 3.8
HJ4197-SEP1
1½ 50 23
HL4197
Class 30 6.8 25 5.6
HL4197-SEP1
150 1450 200 14 400 27 350 175
AS4197 Flanged 35 8 45 10
AS4197-SEP1
115 52
AK4197
3 50 11 1150 70 16
AK4197-SEP1
AL4197
75 17 95 22 120 55
AL4197-SEP1

① If suction pressure exceeds 100 PSI (7 BAR), consult factory.

② Standard PTFE seal from 0°F to +350°F (-20°C to +175°C). Extra clearances are required above 225°F (105°C).
③ Nominal capacities based on handling thin liquids at 1800 RPM on GG, HJ and HL sizes, 1200 RPM on AS, AK and AL sizes.
④ Maximum hydrostatic pressure for standard pump construction. Rating is dependent on seal, gaskets and ports.
⑤ 4197-SEP1 Fluorosilicone seal from -95°F to +225°F (-70°C to +105°C)
* 200 PSI (14 BAR) for above 750 SSU (162 cSt),
150 PSI (10 BAR) for 100 to 750 SSU (20 to 162 cSt),
100 PSI (7 BAR) for 38 to 100 SSU (3 to 20 cSt),
75 PSI (5 BAR) for below 38 SSU (3 cSt) (solvents, alcohols, aqueous solutions and similar liquids)

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

MOTOR SPEED PRODUCT LINE: Section 1741
STAINLESS STEEL PUMPS Page 1741.3
4197 Series™, 4197-SEP Series™ Issue F

MODEL NUMBER KEY

A K 4 1 9 7 - S E P 1
Size: Shaft Seal: Basic Series Application Specific Construction:
GG 4 = Mechanical Seal Configuration -SEP1 = Solvent Extraction Pump
HJ
Material of Construction
HL
7 = Stainless Steel
AS Mounting:
AK 1 = Foot Mount
AL

CUTAWAY VIEW & PUMP FEATURES

Behind the rotor seal,

so shaft and bearings
Sealed anti-friction not exposed to media
bearings eliminate the Pressure lubricated idler pin
need for relubrication lubricates the idler pin / bushing
interface to extend life on thin
liquids. (AS-AL)

Threaded one-piece
bearing housing allows for Class 150 flanged ports
end clearance adjustment enable easy in-line mounting
to almost any piping system
One-piece casing ensures alignment
for maximum bearing and seal life

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

 Section 1741 MOTOR SPEED PRODUCT LINE:
Page 1741.4 STAINLESS STEEL PUMPS
Issue F 4197 Series™, 4197-SEP Series™

MOUNTING OPTIONS

Direct Drive (D Drive)

Pump and motor mounted on a base
with coupling and coupling guard.
Sizes: GG, HJ, HL, AS, AK, AL
4197 Series™ and 4197-SEP Series™ D Drive units in the
GG, HJ and HL size (nomi­nal rating 10, 20, 30 GPM) are
designed for high-speed, heavy-duty service. The pump
is connected by a flexible coupling with guard directly to
a 1200 or 1800 RPM motor. Both pump and motor mount
on a sturdy formed steel base.
Sizes AS, AK and AL D Drive direct-connected units all
feature the 4197 Series™ or 4197-SEP Series™ high-speed
pump connected by a flexi­ble coupling with guard to 1200
RPM motor. Both pump and motor are mounted on a formed (Shown with optional drip rim and
steel base. non-sparking aluminum guard)

These make very compact, rugged units for heavy duty

service, handling many types of liquids up to 25,000 SSU
(5,500 cSt).

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

MOTOR SPEED PRODUCT LINE: Section 1741
STAINLESS STEEL PUMPS Page 1741.5
4197 Series™, 4197-SEP Series™ Issue F

DIMENSIONS – GG, HJ, HL SIZES

Model A U V
Number (in) B D E F G H J K L M N O P S T (in) (in) W X
GG4197 in 4.00 2.75 1.62 1.31 4.00 2.44 0.34 0.94 0.03 0.66 1.12 0.31 0.62 7.31 1.12 .12 x 2.66 0.38
1 0.50
GG4197-SEP1 mm 102 70 41 33 102 62 9 24 1 17 29 8 16 186 29 .06 67 10
HJ4197 in 4.00 4.12 1.75 2.00 5.00 3.50 0.41 1.50 1.25 0.88 1.50 0.44 0.62 10.00 1.62 .19 x 2.84 0.75
1½ 0.75
HJ4197-SEP1 mm 102 105 44 51 127 89 10 38 32 22 38 11 16 254 41 .09 72 19
HL4197 in 4.00 4.12 1.75 2.00 5.00 3.50 0.41 1.50 1.25 0.88 1.50 0.44 0.62 10.00 1.62 .19 x 2.84 0.75
1½ 0.75
HL4197-SEP1 mm 102 105 44 51 127 89 10 38 32 22 38 11 16 254 41 .09 72 19

DIMENSIONS – AS, AK, AL SIZES

Model A U V
Number (in) B D E F G H J K L M N O P S T (in) (in) W X Z
AS4197 in 6.00 5.25 2.88 2.00 6.75 4.00 0.41 2.25 1.25 1.00 2.00 0.44 1.12 12.12 2.38 .25 x 7.00 0.50 1.56
3 1.00
AS4197-SEP1 mm 152 133 73 51 171 102 10 57 32 25 51 11 29 308 60 .12 178 13 40
AK4197 in 6.00 5.25 2.88 2.00 6.75 4.00 0.41 2.25 1.25 1.00 2.00 0.44 1.12 12.12 2.38 .25 x 7.00 0.50 1.56
3 1.00
AK4197-SEP1 mm 152 133 73 51 171 102 10 57 32 25 51 11 29 308 60 .12 178 13 40
AL4197 in 6.00 5.25 2.88 2.00 6.75 4.00 0.41 2.25 1.75 1.00 2.50 0.44 1.12 12.12 2.38 .25 x 7.00 0.50 1.56
3 1.00
AL4197-SEP1 mm 152 133 73 51 171 102 10 57 44 25 64 11 29 308 60 .12 178 13 40

NOTE: Models AS and AK have 2½” cored opening.

These dimensions are average and not for construction purposes. Certified prints on request.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

 Section 1741 MOTOR SPEED PRODUCT LINE:
Page 1741.6 STAINLESS STEEL PUMPS
Issue F 4197 Series™, 4197-SEP Series™

DIMENSIONS – GG, HJ, HL, AS, AK, AL SIZES (D DRIVE)

A
Model Motor Frame Size (in) B D E F H J K L M M1 N P S
GG4197 in 4.00 3.50 1.50 20.50 0.75 0.75 8.50 0.38 3.78 0.62 0.62 4.25
56, 143T, 145T 1 —
GG4197-SEP1 mm 102 89 38 521 19 19 216 10 96 16 16 108
in 4.00 3.50 ① 2.12 20.50 0.75 0.75 8.50 — 4.34 0.62 0.62 4.25
56, 143T, 145T 1½
HJ4197 mm 102 89 54 521 19 19 216 — 110 16 16 108
HJ4197-SEP1 in 4.00 4.50 2.94 29.00 1.00 1.50 9.00 0.25 4.34 0.62 0.62 4.50
182, 182T, 184, 184T 1½ —
HL4197 mm 102 114 75 737 25 38 229 6 110 16 16 114
HL4197-SEP1 in 4.00 5.25 2.94 29.00 1.00 1.50 9.00 0.25 4.34 0.62 0.62 4.50
213, 213T, 215, 215T 1½
mm 102 133 75 737 25 38 229 6 110 16 16 114
in 6.00 4.50 ② 3.69 29.00 1.00 1.50 9.00 — 7.00 1.12 0.62 4.50
AS4197 182, 182T, 184, 184T 3
AS4197-SEP1 mm 152 114 94 737 25 38 229 — 178 29 16 114
AK4197 in 6.00 5.25 2.94 34.00 1.00 1.50 9.00 — 7.00 1.12 0.62 4.50
213, 213T, 215, 215T 3 —
AK4197-SEP1 mm 152 133 75 864 25 38 229 — 178 29 16 114
AL4197 in 6.00 6.25 4.00 39.00 1.38 1.38 16.00 3.75 7.00 1.12 0.62 8.00
AL4197-SEP1 254U, 254T, 256U, 256T 3
mm 152 159 102 991 35 35 406 95 178 29 16 203

① Dimension includes motor block, base height is 1½”.

② Dimension includes motor block, base height is 2 ¹⁵⁄₁₆”.
NOTE: AS and AK sizes have 2½” cored opening.
NOTE: All AS, AK, AL sizes are available with any of the three motors shown in columns.

These dimensions are average and not for construction purposes. Certified prints on request.

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020

MOTOR SPEED PRODUCT LINE: Section 1741
STAINLESS STEEL PUMPS Page 1741.7
4197 Series™, 4197-SEP Series™ Issue F

NPSH REQUIRED
Printed performance curves are not available.
Performance curves can be electronically generated with the Viking Pump Curve Generator on vikingpump.com.
NPSHR data is not available on the curve generator.

NPSH (Net Positive Suction Head): The NPSHR (Net Positive Suction Head Required by the pump) is given in the table below
and applies for viscosities through 750 SSU. NPSHA (Net Positive Suction Head – Available in the system) must be greater than
the NPSHR. For a complete explanation of NPSH, see Application Data Sheet AD-19.
FOR VISCOSITIES UP TO 750 SSU – See NPSHR table below.
NPSHR for high viscosities can be estimated using the following method:
1. Calculate line loss for a 1 foot long pipe of a diameter matching the pump inlet port size. Use your flow rate and max viscosity.
2. Convert this value into Feet of Liquid (S.G. 1.0)
3. Add this value to the NPSHR value in the chart below.

PUMPS SPEED, RPM

PUMP SIZE
520 640 780 950 1150 1450 1750
GG 1.6 2.2 2.6 3.1 3.9 5.6 7.6
HJ, HL 2 2.8 3.4 4.5 6.2 9.5 13.5
AS, AK, AL 2.8 3.9 5.5 7.7 11.2 16.8 23.3

Note: NPSHR – FEET OF LIQUID (Specific Gravity 1.0), Viscosities up to 750 SSU

• A Unit of IDEX Corporation • Cedar Falls, IA ©2020