Scribd
Upload
129 views4 pages

Hard Disk PCB Repair Training Guide

The document provides an overview of Module D2 which focuses on hard disk PCB repair training. It discusses [1] basic electronics concepts for hard disk components, [2] common problems in hard disks due to PCB faults such as components being damaged, open, or shorted, and [3] an introduction to the different sections of a hard disk PCB including identifying chips, components, and block diagrams to explain how the PCB works.

Uploaded by

Falco de Zwart
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
129 views4 pages

Hard Disk PCB Repair Training Guide

The document provides an overview of Module D2 which focuses on hard disk PCB repair training. It discusses [1] basic electronics concepts for hard disk components, [2] common problems in hard disks due to PCB faults such as components being damaged, open, or shorted, and [3] an introduction to the different sections of a hard disk PCB including identifying chips, components, and block diagrams to explain how the PCB works.

Uploaded by

Falco de Zwart
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

MODULE D2 HARD DISK REPAIR TRAINING.

MODULE D2 HARD DISK PCB REPAIR TRAINING.

D2.1 SMD Basic electronics for hard disk components and PCB repair

• Basic electronics fast revision.


• Working concept of electronics component resistor, capacitor, diode, transistor, fuse, tvs diode, MOSFET, etc.
• Multimeter basic concept, testing different components.
• Measuring and Identify ok, Short, Open components.
• Introduction to component of hard disk PCB , resistor, capacitor, diode, transistor, MOSFET chips.
• Removing and Inserting Different components.
• Working concept of chips,
D2.2 COMMON PROBLEMS IN HARD DISK DUE TO PCB FAULT.

D2.2 COMMON PROBLEMS IN HARD DISK DUE TO PCB FAULT.

• Totally dead Hard Drive does not spin up *Protection fuse, 0ohms resistor open
• When hard disk connects to computer, *PCB Damaged due to liquid
computer does not start or hangs *Fire Damage
• Broken power connectors *Ceramic capacitor short
• Broken data connectors *Mosfet short, or not giving output
• Spindle/arm driver chip failure *Data connector resistor open
• You can see a burned component *Electric shock
on the hard drive circuit board. *Pcb circuit open / short
• Connector of motor or head is damaged
• Printed circuit board failures including pre-amplification
• TVS diode blow up
D2.3 INTRODUCTION HARD DISK PRINTED CIRCUIT BOARD, BLOCK DIAGRAM, SECTION OF PCB

D2. 3 INTRODUCTION HARD DISK PRINTED CIRCUIT BOARD, BLOCK DIAGRAM,


SECTION OF PCB.

INTRODUCTION TO DIFFERENT SECTION OF HARD DISK.

•Introduction & Block diagram of hard disk printed circuit board.


• Identify different chips on hard disk
• Mcu, driver chip, flah ram chip , buffer chip.
• Identify different component on hard disk.
• Resistor, capacitor, tvs diode, transistor, fuse , inductor, rectifier.
• identify circuit types, no models.
• Block diagram of hard disk pcb.
• How pcb work.
• Identify hard disk pcb .
HARD DISK SECTION
1

• Hard disk Power section normal molex, sata.


• Hard disk Dc to dc converter section. 9
2

• Hard disk Data section connection sata pata.


8

• Hard disk Firmware section.


3

• Hard disk Ram/ Buffer section.


• Hard disk Vcm controller section. 10
4

• Hard disk Spindle motor controller.


7
• Hard disk Mcu section.
6
• Hard disk Pre amplifier section. 5

• Hard disk Head contact section.


• Hard disk Spindle motor section. 11

You might also like