Yamaha Ysp-4300 Ysp-3300 Ysp-Cu4300 Ysp-Cu3300 ns-wsw160
Uploaded by
barber1Yamaha Ysp-4300 Ysp-3300 Ysp-Cu4300 Ysp-Cu3300 ns-wsw160
Uploaded by
barber1DIGITAL SOUND PROJECTOR YSP-4300/YSP-3300
YSP-CU4300/YSP-CU3300/
CENTER UNIT YSP-CU4300/YSP-CU3300
NS-WSW160
WIRELESS SUBWOOFER NS-WSW160
SERVICE MANUAL
The YSP-4300 consists of the YSP-CU4300 and NS-WSW160.
The YSP-3300 consists of the YSP-CU3300 and NS-WSW160.
YSP-4300 は、YSP-CU4300 および NS-WSW160 で構成されています。
YSP-3300 は、YSP-CU3300 および NS-WSW160 で構成されています。
F T
IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known
A
and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury,
destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise
R
all Yamaha product owners that any service required should be performed by an authorized Yamaha Retailer or the
appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
D
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service
departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and specifications
are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's
Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
■ CONTENTS
TO SERVICE PERSONNEL ............................................2 SELF-DIAGNOSTIC FUNCTION /
SYSTEM COMPOSITION / システム構成 .......................3 ダイアグ（自己診断機能）.....................................57–80
FRONT PANELS .........................................................4–6 DISPLAY DATA .......................................................81–82
REAR PANELS ......................................................... 7–15 IC DATA ................................................................. 83–107
REMOTE CONTROL PANELS ..................................... 16 BLOCK DIAGRAM ...............................................108–111
SPECIFICATIONS / 参考仕様 ................................. 17–22 PRINTED CIRCUIT BOARDS ............................. 112–125
INTERNAL VIEW ..........................................................23 PIN CONNECTION DIAGRAMS ................................. 126
SERVICE PRECAUTIONS / サービス時の注意事項 .....24 SCHEMATIC DIAGRAMS ................................... 127–137
DISASSEMBLY PROCEDURES / 分解手順 ...........25–36 REPLACEMENT PARTS LIST ............................ 139–165
UPDATING FIRMWARE / REMOTE CONTROL ........................................... 166–169
ファームウェアのアップデート ............................37–53 ADVANCED SETUP .................................................... 170
WRITING SYSTEM MODEL NAME AND DESTINATION /
システムモデル名と仕向け先の書き込み ..............54–56
Copyright © Yamaha Corpration All rights reserved.
101252 This manual is copyrighted by Yamaha and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
'12.11
YSP-CU4300/YSP-CU3300/NS-WSW160
■ TO SERVICE PERSONNEL AC LEAKAGE
1. Critical Components Information WALL EQUIPMENT TESTER OR
OUTLET UNDER TEST EQUIVALENT
YSP-CU4300/YSP-CU3300/
Components having special characteristics are marked and
must be replaced with parts having specifications equal to those
NS-WSW160
originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
INSULATING
that all exposed conductive surfaces are properly insulated TABLE
from supply circuits.
• Meter impedance should be equivalent to 1500 ohms shunted • Leakage current must not exceed 0.5mA.
by 0.15 μF. • Be sure to test for leakage with the AC plug in both polarities.
YSP-CU4300/YSP-CU3300
For U model
“CAUTION”
“F1: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 6A, 125V
FUSE.”
For C model
CAUTION
T
F1: REPLACE WITH SAME TYPE 6A, 125V FUSE.
ATTENTION
F
F1: UTILISER UN FUSIBLE DE RECHANGE DE MÉME TYPE DE 6A, 125V.
NS-WSW160
A
For U model
“CAUTION”
R
“F301: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 2A, 125V
FUSE.”
For C model
D
CAUTION
F301: REPLACE WITH SAME TYPE 2A, 125V FUSE.
ATTENTION
F301: UTILISER UN FUSIBLE DE RECHANGE DE MÉME TYPE DE 2A, 125V.
WARNING: CHEMICAL CONTENT NOTICE!
This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive
harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON
WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or
expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
About lead free solder / 無鉛ハンダについて
All of the P.C.B.s installed in this unit and solder joints are 本機に搭載されているすべての基板およびハンダ付けに
soldered using the lead free solder. よる接合部は無鉛ハンダでハンダ付けされています。
Among some types of lead free solder currently available, 無鉛ハンダにはいくつかの種類がありますが、修理時に
it is recommended to use one of the following types for は下記のような無鉛ハンダの使用を推奨します。
the repair work. Sn+Ag+Cu（錫 + 銀 + 銅）
• Sn + Ag + Cu (tin + silver + copper) Sn+Cu（錫 + 銅）
• Sn + Cu (tin + copper) Sn+Zn+Bi（錫 + 亜鉛 + ビスマス）
• Sn + Zn + Bi (tin + zinc + bismuth)
注意：
Caution: 無鉛ハンダの融点温度は通常の鉛入りハンダに比べ 30 ∼
As the melting point temperature of the lead free solder 40℃程度高くなっていますので、それぞれのハンダに合っ
is about 30°C to 40°C (50°F to 70°F) higher than that of たハンダごてをご使用ください。
the lead solder, be sure to use a soldering iron suitable
2 to each solder.
YSP-CU4300/YSP-CU3300/NS-WSW160
■ SYSTEM COMPOSITION / システム構成
• The YSP-4300 consists of the YSP-CU4300 and ・ YSP-4300 は、YSP-CU4300 および NS-WSW160 で構成
YSP-CU4300/YSP-CU3300/
NS-WSW160. されています。
• The YSP-3300 consists of the YSP-CU3300 and ・ YSP-3300 は、YSP-CU3300 および NS-WSW160 で構成
NS-WSW160
NS-WSW160. されています。
YSP-4300
▼ NS-WSW160
▼ YSP-CU4300
YSP-3300
F T
A
▼ NS-WSW160
▼ YSP-CU3300
D R
3
YSP-CU4300/YSP-CU3300/NS-WSW160
■ FRONT PANELS
YSP-CU4300
YSP-CU4300/YSP-CU3300/
NS-WSW160
Top view
Front view
F T
R A
D
4
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU3300
YSP-CU4300/YSP-CU3300/
NS-WSW160
Top view
Front view
F T
R A
D
5
YSP-CU4300/YSP-CU3300/NS-WSW160
NS-WSW160
YSP-CU4300/YSP-CU3300/
Front view Side view
NS-WSW160
F T
R A
D
6
YSP-CU4300/YSP-CU3300/NS-WSW160
■ REAR PANELS
YSP-CU4300
YSP-CU4300/YSP-CU3300/
Rear view
NS-WSW160
U, C, T, B, G, F models
A, K, L, V, S, H models
F T
A
J model
Bottom view
D R
Label
7
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300
YSP-CU4300/YSP-CU3300/
Labels
NS-WSW160
U, C models
T model K model
F T
R A
D
A model B, G, F models
8
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300/YSP-CU3300/
NS-WSW160
L, H models V, S models
J model
F T
R A
D
9
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU3300
YSP-CU4300/YSP-CU3300/
Rear view
NS-WSW160
U, C, T, B, G, F models
A, K, L, V, S, H models
F T
A
J model
Bottom view
D R
Label
10
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU3300
YSP-CU4300/YSP-CU3300/
Labels
NS-WSW160
U, C models
T model
F
K model
T
R A
D
A model B, G, F models
11
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300/YSP-CU3300/
L, H models V, S models
NS-WSW160
F T
J model
R A
D
12
YSP-CU4300/YSP-CU3300/NS-WSW160
NS-WSW160
YSP-CU4300/YSP-CU3300/
U, C models
NS-WSW160
Rear view
F T
R A
D
13
YSP-CU4300/YSP-CU3300/NS-WSW160
T model K model
YSP-CU4300/YSP-CU3300/
NS-WSW160
F T
A
A model B, G, F models
D R
14
YSP-CU4300/YSP-CU3300/NS-WSW160
L, H models V model
YSP-CU4300/YSP-CU3300/
NS-WSW160
T
H model
S model
A F
J model
D R
15
YSP-CU4300/YSP-CU3300/NS-WSW160
■ REMOTE CONTROL PANELS
YSP-CU4300 YSP-CU3300
YSP-CU4300/YSP-CU3300/
FSR131 FSR130 FSR131 FSR130
NS-WSW160
(U, C, T, K, A, B, G, F, L, (J model) (U, C, T, K, A, B, G, F, L, (J model)
V, S, H models) V, S, H models)
F T
R A
D
16
YSP-CU4300/YSP-CU3300/NS-WSW160
■ SPECIFICATIONS / 参考仕様
YSP-CU4300 YSP-CU3300
YSP-CU4300/YSP-CU3300/
■ Amplifier Section / アンプ部 ■ FM Tuner Section / FM チューナー部 [YSP-CU4300]
NS-WSW160
Rated Output Power / 定格出力 (1 % THD) Tuning Range / 受信周波数範囲
SUBWOOFER (100 Hz) U, C models .................................................. 87.5 to 107.9 MHz
[YSP-CU4300] (4 ohms) ...............................124 W (62 W x 2) T, K, A, B, G, F, L, V, S, H models .............. 87.50 to 108.00 MHz
[YSP-CU3300] (6 ohms) .................................90 W (45 W x 2) J model ........................................................... 76.0 to 90.0 MHz
TWEETER (1 kHz, 4 ohms) Frequency Step / 周波数ステップ
[YSP-CU4300] .............................................................. 37.4 W U, C models .................................................................. 200 kHz
[YSP-CU3300] .............................................................. 27.2 W T, K, A, B, G, F, L, V, S, H models .................................... 50 kHz
J model ......................................................................... 100 kHz
Maximum Effective Output Power / 実用最大出力
(JEITA, 10 % THD) Antenna Input / アンテナ入力
SUBWOOFER (100 Hz) ................................................................ 75 ohms unbalanced
[YSP-CU4300] (4 ohms) ...............................150 W (75 W x 2)
T
[YSP-CU3300] (6 ohms) ...............................100 W (50 W x 2)
■ Speaker Section / スピーカー部
TWEETER (1 kHz, 4 ohms)
SUBWOOFER L/R
F
[YSP-CU4300] ................................................................. 44 W
[YSP-CU3300] ................................................................. 32 W Type / 型式
......................................... Acoustic suspension type / 密閉型
A
Total Maximum Output Power / 総合最大出力
[YSP-CU4300] .............................. 194 W (2 W x 22 + 75 W x 2) Driver / スピーカーユニット (Full-range)
........................................... 6.5 x 10 cm (2-1/2" x 3-7/8") cone
R
[YSP-CU3300] .............................. 132 W (2 W x 16 + 50 W x 2)
Non-magnetic shielding type x 2
Maximum Input Signal / 最大許容入力 (1 kHz) 6.5 x 10 cm コーン 非防磁型 x 2
Analog input (DSP through) ....................................2.2 V or less
D
Frequency Response / 再生周波数帯域 (*1)
Total Harmonic Distortion / 全高調波歪率 (20k L.P.F., 1 kHz) .....................................................................160 Hz to 22 kHz
SUBWOOFER Impedance / インピーダンス
[YSP-CU4300] (4.4 V, 4 ohms) ..........................0.05 % or less [YSP-CU4300] ..............................................................4 ohms
[YSP-CU3300] (5.0 V, 6 ohms) ..........................0.05 % or less [YSP-CU3300] ..............................................................6 ohms
TWEETER (1.0 V, 4 ohms) ....................................0.08 % or less TWEETER
Type / 型式
■ HDMI Section / HDMI 部 ......................................... Acoustic suspension type / 密閉型
Driver / スピーカーユニット
HDMI Specification / HDMI 規格
[YSP-CU4300] .........................................2.8 cm (1-1/8") cone
................................................................................Version 1.4a
Magnetic shielding type x 22
Content Protection / 著作権保護 2.8 cm コーン 防磁型 x 22
...... HDCP (High-bandwidth Digital Content Protection system) [YSP-CU3300] .........................................2.8 cm (1-1/8") cone
Magnetic shielding type x 16
Audio Format / 音声フォーマット
2.8 cm コーン 防磁型 x 16
...................................HD audio, SD audio, M-ch LPCN, Stereo
Frequency Response / 再生周波数帯域 (*1)
Video Format / 映像フォーマット
.....................................................................500 Hz to 22 kHz
................................................ Up to 4K (4,096 x 2,160p/24Hz)
Impedance / インピーダンス
Link Function / リンク機能
.....................................................................................4 ohms
.............................................................................. HDMI control
Based on version 1.4a audio control *1 Frequency of total sets
(YSP-CU4300 or YSP-CU3300 and NS-WSW160)
Auto Lip Sync / オートリップシンク
Frequency Response / 再生周波数帯域
...........................................................................max. 500 msec
..................................................................30 Hz to 22 kHz
ARC Function / ARC 機能
Crossover Frequency / クロスオーバー周波数
................................................................ Audio Return Channel
Based on version 1.4a ........................................160 Hz (stereo play back mode)
160 Hz, 500 Hz (surround play back mode)
17
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300/YSP-CU3300/
■ Wireless Section / 無線部
NS-WSW160
Band Frequency / 周波数帯域 Accessories / 付属品
...................................................................................... 2.4 GHz Remote control .......................................................................x 1
Transmission Range / 通信距離 Battery (R03, AAA, UM-4) ......................................................x 2
(Without interference / 妨害のないとき ) FM antenna (1.4 m) [YSP-CU4300] ...................x 1
....................................................................approx. 20 m (66 ft) Optical cable (1.5 m) .............................................................x 1
IntelliBeam microphone (6 m) ................................................x 1
Cardboard microphone stand ...............................................x 1
■ General / 総合
Spacer ...................................................................................x 1
Power Supply / 電源電圧 DVD-ROM (Demo disc) (J model) ............................x 1
U, C models ..................................................... AC 120 V, 60 Hz iPod transmitter (YIT-W12TX) (T, A, B, G, F, J models) .....x 1
T, K, A, B, G, F, L, H models ............... AC 220–240 V, 50/60 Hz USB cable (300 mm, A-microB) (T, A, B, G, F, J models) .....x 1
V, S models ......................................... AC 110–120 V, 50/60 Hz
T
J model ....................................................... AC 100 V, 50/60 Hz
* Specifications are subject to change without notice.
Power Consumption / 消費電力
F
※ 参考仕様および外観は、製品の改良のため予告なく変更する
[YSP-CU4300] .................................................................... 45 W ことがあります。
[YSP-CU3300] .................................................................... 40 W
A
U .......................U.S.A. model F .................... Russian model
Standby Power Consumption / 待機時消費電力 C .................Canadian model L .................Singapore model
(at the default setting / 初期設定時 ) T .................... Chinese model V ..................... Taiwan model
R
U, C models K ..................... Korean model S .................. Brazilian model
A ................Australian model H ..........................Thai model
HDMI control: OFF / Wireless interlock: OFF
B ......................British model J .................. Japanese model
.....................................................................Less than 0.5 W G .................European model
D
T, K, A, B, G, F, L, V, S, H models
HDMI control: OFF / Wireless interlock: ON
.....................................................................Less than 2.0 W
J model
HDMI control: ON / Wireless interlock: ON
.....................................................................Less than 2.5 W
Dimensions (W x H x D) / 寸法（幅 × 高さ × 奥行き）
[YSP-CU4300]
............................................................1,102 x 99.5 x 161 mm
43-3/8" x 3-7/8" x 6-3/8"
[YSP-CU3300]
............................................................1,002 x 99.5 x 161 mm
39-1/2" x 3-7/8" x 6-3/8"
Weight / 質量
[YSP-CU4300]
..................................................................... 6.9 kg (15.2 lbs.)
[YSP-CU3300]
..................................................................... 6.3 kg (13.9 lbs.)
Finish / 仕上げ
U, C, T, K, A, B, G, F, L, V, S, H, J models ................ Black color
U, K, A, B, G, F, L, V, S, H, J models .........................Silver color
18
YSP-CU4300/YSP-CU3300/NS-WSW160
NS-WSW160
YSP-CU4300/YSP-CU3300/
NS-WSW160
Type / 型式
...................... Advanced Yamaha Active Servo Technology * Specifications are subject to change without notice.
Linear Port
※ 参考仕様および外観は、製品の改良のため予告なく変更する
Wireless Unit / 無線ユニット (Air Wired) ことがあります。
Band Frequency / 周波数帯域 U .......................U.S.A. model F .................... Russian model
................................................................................... 2.4 GHz C .................Canadian model L .................Singapore model
T .................... Chinese model V ..................... Taiwan model
Transmission Range / 通信距離 K ..................... Korean model S .................. Brazilian model
(Without interference / 妨害のないとき ) A ................Australian model H ..........................Thai model
B ......................British model J .................. Japanese model
.................................................................approx. 20 m (66 ft)
G .................European model
Transmission Delay / 通信遅延時間
Group ID (A, B) ...........................................................12 msec
Group ID (C) ...............................................................50 msec
T
Output Power / 出力 (100 Hz, 10 % THD, 5 ohms)
F
...................................................................................... 75 W The “ ” and “yAired” are trademarks of Yamaha Corporation.
Dynamic Power / ダイナミックパワー
A
.................................................................................... 130 W The “ ” and “AirWired” are trademarks of Yamaha Corporation.
「エアワイヤード」「AirWired」は、ヤマハ株式会社の商標です。
Frequency Response / 再生周波数帯域
R
........................................................................30 Hz to 200 kHz
The “ ” logo and “IntelliBeam” are trademarks of Yamaha
Driver / スピーカーユニット
Corporation.
....................................................................16 cm (6-1/4") cone
D
「インテリビーム」「IntelliBeam」は、ヤマハ株式会社の商標です。
Non-magnetic shielding type x 1
16 cm コーン 非防磁型 x 1
The “ ” logo and “Cinema DSP” are registered trademarks of
Power Supply / 電源電圧 Yamaha Corporation.
U, C models ..................................................... AC 120 V, 60 Hz 「シネマ DSP」「CINEMA DSP」は、ヤマハ株式会社の登録商標です。
T model ............................................................ AC 220 V, 50 Hz
K model ............................................................ AC 220 V, 60 Hz
“UniVolume” is a trademark of Yamaha Corporation.
A model ............................................................ AC 240 V, 50 Hz
「ユニボリューム」「UniVolume」は、ヤマハ株式会社の商標です。
B, G, F models ................................................. AC 230 V, 50 Hz
L, H models ......................................... AC 220–240 V, 50/60 Hz
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic,
V, S models .............................................. AC 110–120 V, 60 Hz Surround EX, and the double-D symbol are trademarks of Dolby Laboratories.
J model ....................................................... AC 100 V, 50/60 Hz ドルビーラボラトリーズからの実施権により製造されています。Dolby、ドル
ビー、Pro Logic、及びダブル D 記号 はドルビーラボラトリーズの商標です。
Power Consumption / 消費電力
U, C, T, K, A, B, G, F, L, V, S, H models ............................. 70 W
J model .............................................................................. 45 W DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered
trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights
Dimensions (W x H x D) / 寸法（幅 × 高さ × 奥行き） Reserved.
Horizontal placement / 横置き DTS と DTS-HD、またそのシンボルマークは DTS, Inc. の登録商標です。DTS-
...................... 435 x 146 x 371 mm (17-1/8" x 5-3/4" x 14-5/8") HD、DTS-HD マスターオーディオ及び DTS のロゴは DTS, Inc. の商標です。
「製品」
にはソフトウェアも含みます。©DTS, Inc. 不許複製。
Vertical placement / 縦置き
...................... 145 x 446 x 371 mm (5-3/4" x 17-1/2" x 14-5/8")
“HDMI,” the “HDMI” logo and “High-Definition Multimedia Interface” are
Weight / 質量 trademarks, or registered trademarks of HDMI Licensing LLC.
........................................................................ 9.0 kg (19.8 lbs.) HDMI、HDMI ロゴ、および High-Definition Multimedia Interface は、HDMI
Licensing, LLC の商標または登録商標です。
Finish / 仕上げ
U, C, T, K, A, B, G, F, L, V, S, H, J models ................ Black color
“x.v.Color” is a trademark of Sony Corporation.
「x.v.Color」はソニー株式会社の商標です。
19
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300/YSP-CU3300/
NS-WSW160
Windows is a registered trademark of Microsoft Corporation in the United
States and other countries.
Manufactured under license from Cambridge Mechatronics Ltd. Worldwide Windows XP, Windows Vista, Windows 7, Windows Media Audio and
patents applied for. Windows Media Player are either registered trademarks or trademarks of
The “ ” logo and “Digital Sound Projector™” are trademarks of Cambridge Microsoft Corporation in the United States and/or other countries.
Mechatronics Ltd.
Windows は米国 Microsoft Corporation の米国およびその他の国における登
世界に広く特許申請中の Cambridge Mechatronics Ltd からライセンスを受けて 録商標です。Windows XP、Windows Vista、Windows 7 は、米国 Microsoft
います。 Corporation の米国およびその他の国における登録商標、または商標です。
は Cambridge Mechatronics Ltd の商標です。
iPad, iPhone, iPod, iPod nano, iPod touch, and Macintosh are trademarks
of Apple Inc., registered in the U.S. and other countries. AAC ロゴマークはドルビーラボラトリーズの商標です。
iPad、iPhone、iPod、iPod nano、iPod touch は、米国およびその他の国々で登
録されている Apple Inc. の商標です。
F T
• DIMENSIONS / 寸法図
R A
D
YSP-CU4300
Top view
(3-1/8") (2")
51
160 (6-1/4")
161 (6-3/8")
7930
(1-1/8")
(with SPACER / スペーサーを含む )
Front view (without SPACER / スペーサーを除く )
(3-3/8")
(3-7/8")
99.5
86
1008 (39-5/8")
1102 (43-3/8")
Unit: mm (inch)
単位：mm（インチ）
20
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300/YSP-CU3300/
YSP-CU3300
NS-WSW160
(3-1/8") (2") Top view
51
160 (6-1/4")
161 (6-3/8")
79
30
(1-1/8")
(with SPACER / スペーサーを含む )
Front view (without SPACER / スペーサーを除く )
(3-3/8")
(3-7/8")
99.5
86
908 (35-3/4")
T
1002 (39-1/2")
F
Unit: mm (inch)
単位：mm（インチ）
R A NS-WSW160
D
Horizontal position
(1-5/8")
Top view
ø 60
40
Upright position
Front view Bottom view
371 (14-5/8")
(2-1/2")
245 (9-5/8")
135 (5-3/8")
65
245 (9-5/8")
435 (17-1/8")
446 (17-1/2")
65
(2-1/2")
50 335 (13-1/4") 50
(2") (2")
ø 60
Front view
(5-3/4")
146
40
(1-5/8")
85 30
(3-3/8") (1-1/8")
30 (1-1/8")
145 (5-3/4") 435 (17-1/8")
Unit: mm (inch)
単位：mm（インチ）
21
YSP-CU4300/YSP-CU3300/NS-WSW160
• SET MENU TABLE / セットメニュー
YSP-CU4300/YSP-CU3300/
CATEGORY MENU SUB-MENU VALUE [INITIAL VALUE]
NS-WSW160
BEAM IntelliBeam BEAM+SOUND OPTIMIZE
BEAM OPTIMIZE ONLY AUTO SETUP
SOUND OPTIMIZE ONLY
HORIZONTAL Front L
ANGLE Front R
Center L90° to R90°
Surround L
Surround R
BEAM TRAVEL Front L
LENGTH Front R
Center 0.3 to 24.0 m / 1.0 to 80.0 ft
Surround L
Surround R
Subwoofer 0.3 to 15.0 m, [2.5 m] / 1.0 to 50.0 ft, [8.5 ft]
T
FOCAL Front L -1.0 to +13.0 m / -3.5 to +43.5 ft
LENGTH Front R
F
Center -1.0 to +13.0 m, [-0.5 m] / -3.5 to +43.5 ft, [-1.5 ft]
Surround L -1.0 to +13.0 m / -3.5 to +43.5 ft
A
Surround R
IMAGE ADJUSTMENT [OFF] / ON
R
LOCATION LEFT 0 to 95 %, [0 %]
RIGHT
CHANNEL OUT 5.1ch / 7.1ch / [AUTO]
D
SOUND SPEAKER Front L
LEVEL Front R
Center -20 to +20
Surround L
Surround R
Subwoofer
Adaptive DRC [ON] / OFF
DYNAMIC RANGE [Max] / Standard / Min/Auto
MATRIX 2ch -> 5ch PLII (Dolby Pro Logic II): Movie, Music, Game
Neo:6 (DTS Neo:6): Cinema, Music
2ch -> 7ch PLIIx (Dolby Pro Logic IIx): Movie, Music, Game
DECODER Neo:6 (DTS Neo:6): Cinema, Music
Dolby PLIIx Center Width 0 to 7, [3]
PARAMETER Panorama [OFF] / ON
Dimension -3 to +3, [0]
HDMI HDMI CONTROL [OFF] / ON
HDMI AUDIO OUT [AMP] / TV
TV INPUT [OPTICAL] / COAXIAL
yAired iPod INTERLOCK [OFF] / ON
GROUP ID [A1] to A2 / B1 to B3 / C1 to C3
DISPLAY DIMMER -4 to -1, [0 (brightest)]
OSD 日本語 (Japanese) / ENGLISH (English) / DEUTSCH (German) /
LANGUAGE FRANÇAIS (French) / ESPAÑOL (Spanish) / ITALIANO (Italian) /
NEDERLANDS (Dutch) / РУССКИЙ (Russian) / SVENSKA (Swedish)
DISTANCE UNIT METERS / FEET
INFORMATION AUDIO Format, Number of channels, Sampling frequency, Bit rate
VIDEO Type, Resolution
SYSTEM Firmware version
22
YSP-CU4300/YSP-CU3300/NS-WSW160
■ INTERNAL VIEW
YSP-CU4300 YSP-CU3300
YSP-CU4300/YSP-CU3300/
Top view 1 2 3 4 5 6 7 8 9 10
NS-WSW160
Front view 13 12 11
14 15 16 17 14
T
1 POWER (5) P.C.B. 10 FM TUNER (YSP-CU4300)
F
2 POWER (2) P.C.B. 11 POWER (2) P.C.B.
3 DAMP P.C.B. 12 AWCD2A P.C.B.
4 POWER (7) P.C.B. 13 INPUT (3) P.C.B.
A
5 POWER (6) P.C.B. 14 DRIVER WOOFER
6 DIGITAL P.C.B. 15 INPUT (4) P.C.B.
R
7 POWER (4) P.C.B. 16 DRIVER TWEETERS
8 INPUT (1) P.C.B. 17 INPUT (2) P.C.B. (YSP-CU4300)
9 POWER (3) P.C.B.
Side view 1 2 3
D 4
NS-WSW160
1
2
3
4
AWCD2A P.C.B.
DSP (1) P.C.B.
DSP (2) P.C.B.
MAIN (3) P.C.B.
5 MAIN (1) P.C.B.
6 MAIN (2) P.C.B.
7 POWER TRANSFORMER
8 MAIN (4) P.C.B.
5
9 DRIVER WOOFER
9 8
23
YSP-CU4300/YSP-CU3300/NS-WSW160
■ SERVICE PRECAUTIONS / サービス時の注意事項
Safety measures 安全対策
YSP-CU4300/YSP-CU3300/
• Some internal parts in this product contain high voltages ・ この製品の内部には高電圧部分があり危険です。修理
NS-WSW160
and are dangerous. の際は、絶縁性の手袋を使用するなどの安全対策を
Be sure to take safety measures during servicing, such 行ってください。
as wearing insulating gloves.
• Note that the capacitors indicated below are dangerous ・ 下記のコンデンサには電源を OFF にした後も電荷が残
even after the power is turned off because an electric り、高電圧が維持されており危険です。
charge remains and a high voltage continues to exist 修理作業前に放電用抵抗（5 k Ω /10 W）を下記の各コ
there. ンデンサの端子間に接続して放電してください。
Before starting any repair work, connect a discharging 放電所用時間は各々約 30 秒間です。
resistor (5 k-ohms/10 W) to the terminals of each YSP-CU4300/YSP-CU3300
capacitor indicated below to discharge electricity.
POWER P.C.B. の C8、C44、C48
The time required for discharging is about 30 seconds
per each. NS-WSW160
YSP-CU4300/YSP-CU3300 MAIN P.C.B. の C23、C24
C8, C44 and C48 on POWER P.C.B. 詳しくは PRINTED CIRCUIT BOARDS を参照してくだ
T
さい。
NS-WSW160
F
C23 and C24 on MAIN P.C.B.
For details, refer to “PRINTED CIRCUIT BOARDS”.
A
Precaution for handling measuring instrument 計測機器取り扱い上の注意
R
Since the speaker output of this unit is BTL connected, the 本機のスピーカー出力は BTL 接続となっていますので、
ground side of the measuring instrument to be connected スピーカー端子に接続する計測器のアース側はフロー
to the speaker terminal MUST be kept in floating condition. ティング状態に保つ必要があります。
24
YSP-CU4300/YSP-CU3300/NS-WSW160
■ DISASSEMBLY PROCEDURES / 分解手順
(Remove parts in the order as numbered.) （番号順に部品を外してください。）
YSP-CU4300/YSP-CU3300/
Disconnect the power cable from the AC outlet. AC 電源コンセントから、電源コードを抜いてください。
NS-WSW160
YSP-CU4300 YSP-CU3300
Disassembly procedures of the YSP-CU4300 and YSP- YSP-CU4300 と YSP-CU3300 の分解手順はほぼ同じです。
CU3300 are almost the same. For that reason, we そのため、ここでは代表として YSP-CU3300 の分解手順
explain disassembly procedure of the YSP-CU3300 as a を説明します。
representative here.
1. Removal of Rear Cover 1. リアカバーの外し方
a. Remove 8 screws (①). (Fig. 1) a. ① のネジ 8 本を外します。（Fig. 1）
b. Remove the IR bar A and IR bar B. (Fig. 1) b. IR バー A と IR バー B を外します。（Fig. 1）
c. Remove 12 screws (②). (Fig. 1) c. ② のネジ 12 本を外します。（Fig. 1）
d. Remove the rear cover. (Fig. 1) d. リアカバーを外します。（Fig. 1）
2. Removal of Bottom Panel 2. ボトムパネルの外し方
T
a. Remove 8 screws (③). (Fig. 1) a. ③ のネジ 8 本を外します。（Fig. 1）
b. Remove the bottom panel. (Fig. 1) b. ボトムパネルを外します。（Fig. 1）
A F
Rear cover
リアカバー ①
IR bar B * Length of the IR bar / IR バーの長さ
R
IR バー B
IR bar A: 281.5 mm (11-1/8" inch)
① IR bar B: 191.5 mm (7-1/2" inch)
D
IR bar A
IR バー A
①
IR bar B
IR バー B
①
IR bar A
IR バー A
②
②
Bottom panel
ボトムパネル
Fig. 1
25
YSP-CU4300/YSP-CU3300/NS-WSW160
3. Removal of Cabinet L Assembly 3. キャビネット L Ass'y の外し方
YSP-CU4300/YSP-CU3300/
a. Remove 5 screws (④). (Fig. 2) a. ④ のネジ 5 本を外します。（Fig. 2）
b. Remove the cabinet L assembly. (Fig. 2) b. キャビネット L Ass'y を外します。（Fig. 2）
NS-WSW160
4. Removal of Cabinet R Assembly 4. キャビネット R Ass'y の外し方
a. Remove 5 screws (⑤). (Fig. 2) a. ⑤ のネジ 5 本を外します。（Fig. 2）
b. Remove the cabinet R assembly. (Fig. 2) b. キャビネット R Ass'y を外します。（Fig. 2）
5. Removal of Top Panel 5. トップパネルの外し方
a. Remove 7 screws (⑥). (Fig. 2) a. ⑥ のネジ 7 本を外します。（Fig. 2）
b. Remove the top panel. (Fig. 2) b. トップパネルを外します。 （Fig. 2）
6. Removal of Top Frame 6. トップフレームの外し方
a. Remove 25 screws (⑦). (Fig. 2) a. ⑦ のネジ 25 本を外します。（Fig. 2）
b. Remove CB3, CB9, CB703, CB906 and CB908. b. CB3、CB9、CB703、CB906、CB908 を外します。（Fig. 2）
(Fig. 2) c. トップフレームを外します。（Fig. 2）
T
c. Remove the top frame. (Fig. 2)
A F
Top frame ⑦
トップフレーム Top panel
⑦
トップパネル
D R
Cabinet L assembly
キャビネット L Ass'y
⑥
⑦
⑦
④ ④
④
④
Hook
フック
DAMP P.C.B.
CB908
CB906
⑤
DGITAL P.C.B.
CB3
CB9
CB703 INPUT (1) P.C.B. ⑤
⑤
Cabinet R assembly
キャビネット R Ass'y
26 Fig. 2
YSP-CU4300/YSP-CU3300/NS-WSW160
7. Removal of DAMP P.C.B. 7. DAMP P.C.B. の外し方
YSP-CU4300/YSP-CU3300/
a. Remove 2 screws (⑧) and 7 screws (⑨). (Fig. 3) a. ⑧ のネジ 2 本、⑨ のネジ 7 本を外します。（Fig. 3）
b. Remove CB503, CB504, CB904, CB905, CB907, b. CB503、CB504、CB904、CB905、CB907、CB909、
NS-WSW160
CB909, CB910, CB915 and CB916. (Fig. 3) CB910、CB915、CB916 を外します。（Fig. 3）
c. Remove the DAMP P.C.B. (Fig. 3) c. DAMP P.C.B. を外します。（Fig. 3）
8. Removal of POWER (1) P.C.B. 8. POWER（1）P.C.B. の外し方
a. Remove 6 screws (⑩). (Fig. 3) a. ⑩ のネジ 6 本を外します。（Fig. 2）
b. Remove CB1, CB4, CB6 (POWER (1) P.C.B.), CB6 b. CB1、CB4、CB6（POWER（1）P.C.B.）、CB6（INPUT（1）
(INPUT (1) P.C.B.), CB7 and CB106. (Fig. 3) P.C.B.）、CB7、CB106 を外します。（Fig. 3）
c. Remove the POWER (1) P.C.B. (Fig. 3) c. POWER（1）P.C.B. を外します。（Fig. 3）
⑩ CB1
CB6
F T
R A
⑨ DAMP P.C.B.
POWER (1) P.C.B.
CB907
CB916 CB904
D
CB4 CB7
⑨ CB910
CB915
CB909 CB905
⑨
⑧
DGITAL P.C.B.
INPUT (1) P.C.B.
CB106
CB6
CB503
CB504
Fig. 3
27
YSP-CU4300/YSP-CU3300/NS-WSW160
9. Removal of INPUT (1) P.C.B. 9. INPUT（1）P.C.B. の外し方
YSP-CU4300/YSP-CU3300/
a. Remove 3 screws (⑪) and 2 screws (⑫). (Fig. 4) a. ⑪ のネジ 3 本、⑫ のネジ 2 本を外します。（Fig. 4）
b. Remove CB4, CB7 and CB8. (Fig. 4) b. CB4、CB7、CB8 を外します。（Fig. 4）
NS-WSW160
c. Remove the INPUT (1) P.C.B. (Fig. 4) c. INPUT（1）P.C.B. を外します。（Fig. 4）
10. Removal of DIGITAL P.C.B. 10. DIGITAL P.C.B. の外し方
a. Remove 5 screws (⑬), 2 screws (⑭) and 6 screws a. ⑬ のネジ 5 本、⑭ のネジ 2 本、⑮ のネジ 6 本を外
(⑮). (Fig. 4) します。（Fig. 4）
b. Remove the DIGITAL P.C.B. (Fig. 4) b. DIGITAL P.C.B. を外します。（Fig. 4）
⑮
DIGITAL P.C.B.
⑮
F T
R A
⑫
D CB4
CB8
CB7 INPUT (1) P.C.B.
⑬ ⑪ ⑭
Rear view
Fig. 4
28
YSP-CU4300/YSP-CU3300/NS-WSW160
11. Removal of POWER (2) P.C.B. 11. POWER（2）P.C.B. の外し方
YSP-CU4300/YSP-CU3300/
a. Remove 7 screws (⑯) and 2 screws (⑰). (Fig. 5) a. ⑯ のネジ 7 本、⑰ のネジ 2 本を外します。（Fig. 5）
b. Remove CB4, CB7 (POWER (1) P.C.B.), CB7 (INPUT b. CB4、CB7（POWER（1）P.C.B.）、CB7（INPUT（1）P.C.B.）、
NS-WSW160
(1) P.C.B.), CB904, CB905, CB907, CB909, CB915 CB904、CB905、CB907、CB909、CB915、CB916 を
and CB916. (Fig. 5) 外します。（Fig. 5）
c. Remove 4 screws (⑱). (Fig. 5) c. ⑱ のネジ 4 本を外します。（Fig. 5）
d. Remove the POWER (2) P.C.B. (Fig. 5) d. POWER（2）P.C.B. を外します。（Fig. 5）
12. Removal of Front Panel Unit 12. フロントパネルユニットの外し方
a. Remove 10 screws (⑲), 10 screws (⑳) and 4 screws a. ⑲ のネジ 10 本、⑳ のネジ 10 本、 のネジ 4 本を
( ). (Fig. 5) 外します。（Fig. 5）
b. Remove 2 screws ( ) together with the support. b. のネジ 2 本をサポートと一緒に外します。 （Fig. 5）
(Fig. 5) c. フロントパネルユニットを外します。（Fig. 5）
c. Remove the front panel unit. (Fig. 5)
13. Removal of AWCD2A P.C.B. 13. AWCD2A P.C.B.、INPUT（4）P.C.B. の外し方
and INPUT (4) P.C.B.
T
a. Remove 6 screws ( ). (Fig. 5) a. のネジ 6 本を外します。（Fig. 5）
b. Remove the AWCD2A P.C.B. together with the INPUT b. AWCD2A P.C.B. を INPUT（4）P.C.B. と一緒に外します。
F
(4) P.C.B. (Fig. 5) （Fig. 5）
AWCD2A P.C.B.
Support
A
INPUT (4) P.C.B.
サポート
R
⑳
D
⑰ POWER (2) P.C.B.
⑱
⑱
⑳
Front panel unit ⑲
フロントパネルユニット
⑲
Support
サポート
POWER (1) P.C.B. DAMP P.C.B.
SP unit
CB916 SP ユニット
CB4
CB7
CB915
CB907
CB909
CB904
CB905
INPUT (1) P.C.B.
CB7
⑯
Fig. 5 29
YSP-CU4300/YSP-CU3300/NS-WSW160
14. Removal of Tweeters 14. ツィーターの外し方
YSP-CU4300/YSP-CU3300/
a. Remove the 4 dampers. (Fig. 6) a. ダンパー 4 個を外します。（Fig. 6）
* The old damper, once removed, cannot be ※ 外した古いダンパーは、空気漏れの原因となる恐
NS-WSW160
reused as it may cause air leakage. Be sure to れがあるため、再利用できません。新しいものに
install a new one for its replacement. 交換してください。
b. Remove the SP cabinet. (Fig. 6) b. SP キャビネットを外します。（Fig. 6）
c. Remove 2 screws ( ). Remove the tweeter. (Fig. 6) c. のネジ 2 本を外し、ツィーターを外します。
（Fig. 6）
* Other tweeters can be removed in the same ※ 他のツィーターも同様の方法で外すことができま
manner. す。
SP cabinet
SP キャビネット Tweeter
ツィーター
Damper
ダンパー
F T
R A
Installation of Tweeters
D
Note: Make sure that all the removed tweeters are
reinstalled at specified positions. (Fig. 7)
Fig. 6
ツィーターの取り付け方
注意： 取り外したツィーターはすべて決められた位
置に取り付けてください。（Fig. 7）
SP unit
SP ユニット
YSP-CU4300
CB911 CB912 CB907 CB909 CB904 CB905
T17 T18 T19 T20 T21 T22 T01 T02 T03 T04 T05 T06 T07 T08 T09 T10 T11 T12 T13 T14 T15 T16
YSP-CU4300
Pin No. (Cable color)
CB905 CB904 CB909 CB907 CB912 CB911
ピン番号（線色）
1: (Black), 2: (Red) T13 T12 T05 T04 T20 T19
3: (Black), 4: (Green) T14 T11 T06 T03 T21 T18
5: (Black), 6: (Yellow) T15 T10 T07 T02 T22 T17
7: (Black), 8: (Orange) T16 T09 T08 T01
9: (N.C.) – – –
30 Fig. 7
YSP-CU4300/YSP-CU3300/NS-WSW160
When checking the P.C.B.s: P.C.B. をチェックする場合には：
YSP-CU4300/YSP-CU3300/
• Put the rubber sheet and the cloth over this unit, and ・ 本機の上にゴムシートと布を敷き、その上に P.C.B. を
NS-WSW160
place the sub-chassis unit on them as shown below. 置きます。（Fig. 8）
(Fig. 8) ・ POWER（1）P.C.B. の G2 の ア ー ス を リ ー ド 線 等 で
• Connect the ground points of the POWER (1) P.C.B. シャーシに接続してください。（Fig. 8）
(G2) to the chassis with a ground lead or the like. ・ 外したケーブル（コネクター）をすべて接続します。
(Fig. 8) ・ フラットケーブルを接続する際、極性に注意してく
• Reconnect all cables (connectors) that have been ださい。
disconnected.
• When connecting the flexible flat cable, be careful
with polarity.
Ground lead
アース線
T
POWER (1) P.C.B.
Rubber sheet and cloth
ゴムシートと布
G2
A F
R
DAMP P.C.B.
D
DGITAL P.C.B.
Chassis
シャーシ
INPUT (1) P.C.B.
Cabinet L assembly
キャビネット L Ass'y
AWCD2A P.C.B.
Cabinet R assembly POWER (2) P.C.B.
キャビネット R Ass'y Rubber sheet and cloth
ゴムシートと布 POWER (3) P.C.B.
Fig. 8
31
YSP-CU4300/YSP-CU3300/NS-WSW160
NS-WSW160
YSP-CU4300/YSP-CU3300/
1. Removal of Driver 1. スピーカーユニットの外し方
NS-WSW160
a. Spread a rubber sheet and cloth for protection of this a. 本機に傷などが付かないようにゴムシートと布を敷
unit against any damage and place this unit on cloth き、本機をボトムグリル Ass'y が上になるように置き
with its bottom grille assembly facing up. (Fig. 1) ます。（Fig. 1)
* The bottom grille assembly is fixed to the cabinet ※ ボトムグリル Ass'y は 5 箇所のダボでキャビネッ
with dowels at 5 locations. トに固定されています。
As a flatblade screwdriver is used for removal, use 取り外しの際、キャビネットに傷が付かないよう
special care not to cause damage to the cabinet. 十分注意してください。
b. First, insert a flatblade screwdriver at 2 dowel positions b. 最初にマイナスドライバーを 2 箇所のダボ位置へ差し
and push up the bottom grille assembly. (Fig. 1) 込み、ボトムグリル Ass'y を押し上げます。（Fig. 1）
c. Next, using the metalblade or the like, push the bottom c. 次にヘラ等を使い、徐々に上面ヘ押し上げて、ボトム
grille assembly upward until it comes off. (Fig. 1) グリル Ass'y を外します。（Fig. 1）
Notes: 注意：
• Removing the bottom grille assembly with the flatblade ・ ボトムグリル Ass'y を外す際、ヘラ等を使わずマイ
screwdriver only without using the metalblade or the ナスドライバーだけを使って外すと、ボトムグリル
T
like may cause damage to the bottom grille assembly. Ass'y が破損する場合があります。
• When installing the bottom grille assembly, apply quick- ・ ボトムグリル Ass'y を取り付ける場合、ボトムグリル
F
drying bond or the like to dowels and then fit them into Ass'y のダボに速乾ボンドなどを塗って取り付けます。
dowel holes for secure installation. （ダボへ速乾ボンドなどを塗らずに差し込んだ場合、
(The bottom grille assembly will come off easily if its ボトムグリル Ass'y は容易に外れてしまいます。）
A
dowels are fitted into dowel holes without applying
quick-drying bond or the like.)
R
Bottom grille assembly
ボトムグリル Ass'y
Ruber sheet and the cloth
ゴムシートと布
D Dowel
ダボ
Dowel
ダボ
Dowels
ダボ
Flatblade screwdriver Metalblade
マイナスドライバー ヘラ
32 Fig. 1
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300/YSP-CU3300/
d. Remove 4 screws (①), and pull out the driver. (Fig. 2) d. ① のネジ 4 本を外し、スピーカーユニットを引き出し
NS-WSW160
e. Disconnect the connector connected to the terminal ます。（Fig. 2）
of the driver. (Fig. 2) e. スピーカーユニットの端子に接続されているコネク
f. Remove the driver. (Fig. 2) ターを外します。（Fig. 2）
f. スピーカーユニットを外します。（Fig. 2）
2. Removal of Rear Panel Assembly 2. リアパネル Ass'y の外し方
a. Remove 10 screws (②). (Fig. 2) a. ② のネジ 10 本を外します。（Fig. 2）
b. Remove the rear panel assembly. (Fig. 2) b. リアパネル Ass'y を外します。（Fig. 2）
T
①
F
Driver
A
スピーカーユニット
R
Connector
D
コネクター
Rear panel assembly
リアパネル Ass'y
Ruber sheet and the cloth
② ゴムシートと布
Fig. 2
33
YSP-CU4300/YSP-CU3300/NS-WSW160
3. Removal of Front Panel Assembly 3. フロントパネル Ass'y の外し方
YSP-CU4300/YSP-CU3300/
* The front panel assembly is fixed to the cabinet ※ フロントパネル Ass'y はダボでキャビネット Ass'y
assembly with dowels. As a flatblade screwdriver に固定されています。取り外しの際、キャビネッ
NS-WSW160
is used for removal, use special care not to cause ト Ass'y に傷が付かないよう十分注意してくださ
damage to the cabinet assembly. い。
a. Insert a flatblade screwdriver at 2 dowel positions and a. マイナスドライバーを 2 箇所のダボ位置へ差し込み、
push the front panel assembly frontward. (Fig. 3) フロントパネル Ass'y をフロント側へ押します。
b. Using the metalblade or the like, push the front panel （Fig. 3）
assembly frontward gradually until it comes off. (Fig. 3) b. ヘラ等を使い、フロントパネル Ass'y を徐々にフロン
ト側へ引き出します。（Fig. 3）
Note:
• Removing the front panel assembly with the flatblade 注意：
screwdriver only without using the metalblade or the ・ フロントパネル Ass'y を外す際、ヘラ等を使わずマイ
like may cause a damage to the front panel assembly. ナスドライバーだけを使って外すと、フロントパネル
• When installing the front panel assembly, apply quick- Ass'y が破損する場合があります。
drying bond or the like to dowels and then fit them into ・ フロントパネル Ass'y を取り付ける場合、フロントパ
dowel holes for secure installation. ネル Ass'y のダボに速乾ボンドなどを塗って取り付け
(The front panel assembly will come off easily if its ます。
T
dowels are fitted into dowel holes without applying （フロントパネル Ass'y のダボへ速乾ボンドなどを塗ら
quick-drying bond or the like.) ずに差し込むだけでは、簡単に外れてしまいます。）
F
c. Remove the front panel assembly. (Fig. 3) c. フロントパネル Ass'y を外します。（Fig. 3）
R A
D
Dowel
ダボ
Front panel assembly
フロントパネル Ass'y
Cabinet assembly
キャビネット Ass'y
Flatblad screwdriver
マイナスドライバー
Metalblade
ヘラ
Fig. 3
34
YSP-CU4300/YSP-CU3300/NS-WSW160
4. Removal of AWCD2A P.C.B. 4. AWCD2A P.C.B. の外し方
YSP-CU4300/YSP-CU3300/
a. Remove screw (③). (Fig. 4) a. ③ のネジ 1 本を外します。（Fig. 4）
b. Release hook. (Fig. 4) b. フックを外します。（Fig. 4）
NS-WSW160
c. Remove CB501 and then remove the AWCD2A P.C.B. c. CB501 を外し、AWCD2A P.C.B. を DSP（2）P.C.B. と一
together with the DSP (2) P.C.B. which is connected 緒に外します。（Fig. 4）
directly to the DSP (1) P.C.B. with board-to-board ただし、DSP（2）P.C.B. は DSP（1）P.C.B. に基板対基
connectors. (Fig. 4) 板コネクターで直接接続されています。
Rear panel assembly
リアパネル Ass'y
F T
R A CB501
D
③
Board-to-board connectors
基板対基板コネクター
Hook CB602
フック
DSP (1) P.C.B. DSP (2) P.C.B.
AWCD2A P.C.B.
Fig. 4
35
YSP-CU4300/YSP-CU3300/NS-WSW160
When checking the P.C.B.s: P.C.B. をチェックする場合には：
YSP-CU4300/YSP-CU3300/
• Spread the rubber sheet and the cloth. Then place ・ ゴムシートと布を敷き、その上にリヤパネル Ass'y
NS-WSW160
the rear panel assembly on the cloth and check it. を置いてチェックします。（Fig. 5）
(Fig. 5) ・ 外したケーブル（コネクター）をすべて接続します。
• Reconnect all cables (connectors) that have been ・ フラットケーブルを接続する際、極性に注意してく
disconnected. ださい。
• When connecting the flexible flat cable, be careful
with polarity.
Cabinet assembly
キャビネット Ass'y
F T
R A
Rear panel assembly
D
リヤパネル Ass'y
Rubber sheet and the cloth
ゴムシートと布
Fig. 5
36
YSP-CU4300/YSP-CU3300/NS-WSW160
■ UPDATING FIRMWARE / ファームウェアのアップデート
There are 3 types to write the firmware. ファームウェアを書き込む方法は 3 種類あります。
YSP-CU4300/YSP-CU3300/
Method / 方法 Support Models / 対応するモデル
NS-WSW160
Writing method using the USB storage device YSP-CU4300
USB フラッシュメモリーを使用して書き込む方法
Writing method using the CD YSP-CU3300
CD を使用して書き込む方法
Writing method using the PC (RS-232C)
PC（RS-232C）を使用して書き込む方法 NS-WSW160
YSP-CU4300
When the following parts are replaced, the firmware must 下記の部品を交換した場合、ファームウェアを最新バー
be updated to the latest version. ジョンにアップデートする必要があります。
T
DIGITAL P.C.B. DIGITAL P.C.B.
DSP (TI) FLASH ROM: IC503 on DIGITAL P.C.B. DSP（TI）フラッシュ ROM：DIGITAL P.C.B. の IC503
F
● Confirmation of firmware version and checksum ● ファームウェアのバージョンとチェックサムの確認
A
Before and after updating the firmware, check the ファームウェアのアップデートの前後に、ファーム
firmware version and checksum by using the self- ウェアのバージョンとチェックサムをダイアグで確
R
diagnostic function menu. 認します。
Start up the self-diagnostic function and select “q. ダイアグを起動し、 q. CPU INFORMATION メニュー
D
CPU INFORMATION” menu. を選択します。
Using the sub-menu, have the firmware version and サブメニューでファームウェアのバージョンと
checksum displayed, and note them down. チェックサムを表示し、それらを書きとめます。
(For details, refer to “SELF-DIAGNOSTIC FUNCTION”) （詳細は ダイアグ を参照してください。）
* When the firmware version and checksum are ※ アップデート後、ファームウェアのバージョンと
different from written ones after updating, perform チェックサムが書き込まれたものと異なる場合、
アッ
the updating procedure again from the beginning. プデートの操作を最初からやり直してください。
● Initializing the back-up IC ● バックアップ IC の初期化
(EEPROM: IC703 on DIGITAL P.C.B.) （EEPROM：DIGITAL P.C.B. の IC703）
After updating the firmware, the back-up IC MUST ファームウェアのアップデート後、設定情報（音
be initialized by the following procedure to store the 場プログラムのパラメーターやシステムメモリー、
setting information (soundfield parameters, system チューナープリセット等）を正常に保存するために、
memory and tuner presetting, etc.) properly. 下記の方法でバックアップ IC を初期化する必要が
あります。
Start up the self-diagnostic function and select “o. 本機のダイアグを起動し、 o. FACTORY PRESET メ
FACTORY PRESET” menu. ニューを選択します。
(For details, refer to “SELF-DIAGNOSTIC FUNCTION”) （詳細は ダイアグ を参照してください。）
Select “o2. RESERVE”, press the “ ” (Power) key to o2. RESERVE を選択し、 （電源）キーを押して電
turn off the power once and turn on the power again. 源を一度きってから、もう一度電源を入れるとバッ
Then the back-up IC is initialized. クアップ IC が初期化されます。
37
YSP-CU4300/YSP-CU3300/NS-WSW160
● Required Tools ● 必要なツール
YSP-CU4300/YSP-CU3300/
• USB storage device ・ USB フラッシュメモリー
NS-WSW160
• Firmware ・ ファームウェア
YSP2012-xxxx.bin YSP2012-xxxx.bin
● Preparation ● 準備
1. Download the latest firmware from the specified 1. 指定のダウンロード先から、最新のファームウェ
download source to the folder of the PC. アを PC のフォルダへダウンロードしてください。
2. PC から USB フラッシュメモリーのルートフォル
2. Copy the latest firmware from the PC to the root
ダへ最新のファームウェアをコピーします。
folder of the USB storage device.
注意）最新のファームウェアをサブフォルダにコピー
Note) When the latest firmware is copied to a sub-
した場合、書き込みはできません。
folder of the USB storage device, the update
will not proceed.
F T
R A
D
38
YSP-CU4300/YSP-CU3300/NS-WSW160
● Operation Procedures ● 操作手順
YSP-CU4300/YSP-CU3300/
1. Insert the USB storage device to the USB jack. 1. USB 端子に USB フラッシュメモリーを差し込みま
(Fig. 1)
NS-WSW160
す。（Fig. 1）
2. While pressing the “VOLUME +” key, connect the 2. VOLUME ＋ キーを押しながら、電源コードを
power cable to the AC outlet. (Fig. 1) AC コンセントに接続します。（Fig. 1）
Top view
"VOLUME +" key " " (Power) key
"VOLUME +" キー " "（電源）キー
Front view
FL display
FL ディスプレイ
T
USB jack
USB 端子
USB storage device
F
USB フラッシュメモリー
A
Fig. 1
R
3. The USB UPDATE mode is activated and “USB 3. USB UPDATE モードが起動し、 USB Update が表
Update” is displayed. Writing of the firmware 示されて、ファームウェアの書き込みが自動的に
D
starts automatically. (Fig. 2) 開始されます。（Fig. 2）
Writing is started. / 書き込み開始 Writing being executed. / 書き込み中
USB Update... Connect USB! Update... xx%
Fig. 2
4. When writing of the firmware is completed, 4. ファームウェアの書き込み完了後、 Success 、
“Success”, “Please...” and “Power Off!” are Please... 、 Power Off! が繰り返し表示されます。
displayed repeatedly. (Fig. 3) （Fig. 3）
Writing is completed. / 書き込み完了
Success Please... Power Off!
Fig. 3
5. Press the “ ” (Power) key to turn off the power. 5. （電源）キーを押して電源を切ります。
6. Remove the USB storage device from the USB 6. USB 端子から USB フラッシュメモリーを抜きま
jack. (Fig. 1) す。（Fig. 1）
7. Start up the self-diagnostic function and check that 7. ダイアグを起動し、ファームウェアのバージョン
the firmware version and checksum are the same とチェックサムが、書き込まれたものと同じであ
as written ones. (For details, refer to “Confirmation ることを確認します。
（詳細は ファームウェアの
of firmware version and checksum”) バージョンとチェックサムの確認 を参照してく
ださい。）
39
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU3300
YSP-CU4300/YSP-CU3300/
When the following parts are replaced, the firmware must 下記の部品を交換した場合、ファームウェアを最新バー
NS-WSW160
be updated to the latest version. ジョンにアップデートする必要があります。
DIGITAL P.C.B. DIGITAL P.C.B.
FLASH ROM (IC102) of HDMI/OSD controller HDMI/OSD コントローラーのフラッシュロム（IC102）
● Confirmation of firmware version and checksum ● ファームウェアのバージョンとチェックサムの確認
Before and after updating the firmware, check the ファームウェアのアップデートの前後に、ファーム
firmware version and checksum by using the self- ウェアのバージョンとチェックサムをダイアグで確
diagnostic function menu. 認します。
Start up the self-diagnostic function and select “q. ダイアグを起動し、 q. CPU INFORMATION メニュー
CPU INFORMATION” menu. を選択します。
Using the sub-menu, have the firmware version and サブメニューでファームウェアのバージョンと
T
checksum displayed, and note them down. チェックサムを表示し、それらを書きとめます。
(For details, refer to “SELF-DIAGNOSTIC FUNCTION”) （詳細は ダイアグ を参照してください。）
F
* When the firmware version and checksum are ※ アップデート後、ファームウェアのバージョンと
different from written ones after updating, perform チェックサムが書き込まれたものと異なる場合、
アッ
A
the updating procedure again from the beginning. プデートの操作を最初からやり直してください。
R
● Initializing the back-up IC ● バックアップ IC の初期化
(EEPROM: IC703 on DIGITAL P.C.B.) （EEPROM：DIGITAL P.C.B. の IC703）
D
After updating the firmware, the back-up IC MUST ファームウェアのアップデート後、設定情報（音場
be initialized by the following procedure to store プログラムのパラメーターやシステムメモリー等）
the setting information (soundfield parameters and を正常に保存するために、下記の方法でバックアッ
system memory, etc.) properly. プ IC を初期化する必要があります。
Start up the self-diagnostic function and select “o. 本機のダイアグを起動し、 o. FACTORY PRESET メ
FACTORY PRESET” menu. ニューを選択します。
(For details, refer to “SELF-DIAGNOSTIC FUNCTION”) （詳細は ダイアグ を参照してください。）
Select “o2. RESERVE”, press the “ ” (Power) key to o2. RESERVE を選択し、 （電源）キーを押して電
turn off the power once and turn on the power again. 源を一度きってから、もう一度電源を入れるとバッ
Then the back-up IC is initialized. クアップ IC が初期化されます。
40
YSP-CU4300/YSP-CU3300/NS-WSW160
● Required Tools ● 必要なツール
YSP-CU4300/YSP-CU3300/
• CD, DVD or BD player (with DIGITAL OUTPUT ・ CD、DVD または BD プレーヤー（DIGITAL
(OPTICAL or COAXIAL) jack) OUTPUT（OPTICAL または COAXIAL）端子付き）
NS-WSW160
* The following models can be used as a tool to update the firmware.
下記のモデルはファームウェアのアップデート用に使えます。
CD player: CD-C600/CD-S1000/CD-S2000/CD-S300/CD-S700/CDX-496/CDX-596/CDX-890
DVD player: DV-C6760/DVD-840/DVD-C740/DVD-C750/DVD-C940/DVD-C950/DVD-CX1/DVD-S1200/
DVD-S1800/DVD-S2300(MKII)/DVD-S2700/DVD-S30/DVD-S510/DVD-S520/DVD-S530/
DVD-S540/DVD-S550/DVD-S657/DVD-S700/DVD-S80/DVD-S840
BD (Blu-ray) player: BD-940/BD-S1065/BD-S1900/BD-S2900/BD-S671
Others: CDR-D651/CDR-HD1000/CDR-HD1300/CDR-HD1500/DV-SL100/CDX-E100/CRX-430/
CRX-E150/RDX-E700
• Optical cable (when OPTICAL jack is used) ・ 光ファイバーケーブル（OPTICAL 端子使用時）
• Digital audio pin cable ・ デジタル音声ピンケーブル（COAXIAL 端子使用時）
T
(when COAXIAL jack is used)
・ ファームウェア CD
• Firmware CD 指定のダウンロード先から最新のファームウェア
F
Download the latest firmware from the specified をダウンロードして、ファームウェア CD を製作
download source and create the firmware CD. してください。
A
● Connection ● 接続
R
Connect a CD/DVD/BD player to this unit as shown 本機と CD/DVD/BD プレーヤーを下記のように接続し
below. (Fig. 1) ます。（Fig. 1）
D
Example of OPTICAL jack / OPTICAL 端子使用例
This unit / 本機 (rear view / 後側 )
CD/DVD/BD player
CD/DVD/BD プレーヤー
U, C, T, K, A, B, G, F, L, V, S, H models
J model Optical cable
光ファイバーケーブル
Example of COAXIAL jack / COAXIAL 端子使用例
This unit / 本機 (rear view / 後側 )
CD/DVD/BD player
CD/DVD/BD プレーヤー
U, C, T, K, A, B, G, F, L, V, S, H models
Digital audio pin cable
J model デジタル音声ピンケーブル
Fig. 1
41
YSP-CU4300/YSP-CU3300/NS-WSW160
● Operation Procedures ● 操作手順
YSP-CU4300/YSP-CU3300/
1. While pressing the “VOLUME +” key, connect the 1. VOLUME + キーを押しながら、電源コードを
power cable to the AC outlet. (Fig. 2) AC コンセントに接続します。（Fig. 2）
NS-WSW160
The FIRMWARE UPDATE mode is activated and ファームウェアアップデートモードが起動し、
“PLAY CDDA!” is displayed. (Fig. 2) PLAY CDDA! が表示されます。（Fig. 2）
2. Play the firmware CD on the CD/DVD/BD player. 2. CD/DVD/BD プレーヤーでファームウェア CD を再
Writing of the firmware starts automatically. 生します。 ファームウェアの書き込みが自動的に
開始されます。
Top view
"VOLUME +" key " " (Power) key
"VOLUME +" キー " "（電源）キー
Front view
T
FL display
F
FL ディスプレイ
A
Display / 表示
R
PLAY CDDA!
Fig. 2
D
3. When writing of the firmware is completed,
“Success”, “Please...” and “Power Off!” are
displayed repeatedly. (Fig. 3)
Writing is completed. / 書き込み完了
Success Please...
3. ファームウェアの書き込み完了後、 Success 、
Please... 、 Power Off! が繰り返し表示されます。
（Fig. 3）
Power Off!
Fig. 3
4. Press the “ ” (Power) key to turn off the power. 4. （電源）キーを押して電源を切ります。（Fig. 2）
(Fig. 2)
5. CD/DVD/BD プレーヤーからファームウェア CD
5. Eject the firmware CD from the CD/DVD/BD player. を取り出します。
6. Start up the self-diagnostic function and check 6. ダイアグを起動し、ファームウェアのバージョン
that the firmware version and checksum are the とチェックサムが、書き込まれたものと同じであ
same as written ones. ることを確認します。
(For details, refer to “Confirmation of firmware （詳細は、 ファームウェアのバージョンとチェッ
version and checksum”.) クサムの確認 を参照してください。）
42
YSP-CU4300/YSP-CU3300/NS-WSW160
NS-WSW160
YSP-CU4300/YSP-CU3300/
When the following parts are replaced, the firmware must 下記の部品を交換した場合、ファームウェアを最新バー
NS-WSW160
be updated to the latest version. ジョンにアップデートする必要があります。
Firmware to be updated / アップデートするファームウェア
Replaced parts
Main microprocessor firmware AirWired microprocessor firmware
交換部品
マイコンファームウェア AirWired マイコンファームウェア
DSP P.C.B. yes yes
Main microprocessor (IC501) / メインマイコン（IC501） yes
AWCD2A P.C.B. yes
● Confirmation of firmware version and checksum ● ファームウェアのバージョンとチェックサムの確認
Before and after updating the firmware, check the ファームウェアのアップデートの前後に、ファーム
firmware version and checksum by using the self- ウェアのバージョンとチェックサムをダイアグで確
T
diagnostic function menu. 認します。
F
Start up the self-diagnostic function and select “q. ダイアグを起動し、 q. CPU INFORMATION メニュー
CPU INFORMATION” menu. を選択します。
Using the sub-menu, have the firmware version and サブメニューでファームウェアのバージョンと
A
checksum displayed, and note them down. チェックサムを表示し、それらを書きとめます。
(For details, refer to “SELF-DIAGNOSTIC FUNCTION”) （詳細は ダイアグ を参照してください。）
R
* When the firmware version and checksum are ※ アップデート後、ファームウェアのバージョンと
different from written ones after updating, perform チェックサムが書き込まれたものと異なる場合、
アッ
the updating procedure again from the beginning. プデートの操作を最初からやり直してください。
D
● Initializing the back-up IC ● バックアップ IC の初期化
(EEPROM: IC703 on DIGITAL P.C.B.) （EEPROM：DIGITAL P.C.B. の IC703）
After updating the firmware, the back-up IC MUST ファームウェアのアップデート後、設定情報（セッ
be initialized by the following procedure to store the トメニュー）を正常に保存するために、下記の方法
setting information (set menu) properly. でバックアップ IC を初期化する必要があります。
Start up the self-diagnostic function and select “o. 本機のダイアグを起動し、 o. FACTORY PRESET メ
FACTORY PRESET” menu. ニューを選択します。
(For details, refer to “SELF-DIAGNOSTIC FUNCTION”) （詳細は ダイアグ を参照してください。）
Select “o2. RESERVE”, press the “ ” (Power) key to o2. RESERVE を選択し、 （電源）キーを押して電
turn off the power once and turn on the power again. 源を一度きってから、もう一度電源を入れるとバッ
Then the back-up IC is initialized. クアップ IC が初期化されます。
43
YSP-CU4300/YSP-CU3300/NS-WSW160
● Required tools ● 必要なツール
YSP-CU4300/YSP-CU3300/
• Firmware downloader program ・ ファームウェア書き込み用プログラム
NS-WSW160
Main microprocessor firmware メインマイコンファームウェア
........................................................ FlashSta.exe ................................................................................ FlashSta.exe
AirWired microprocessor firmware AirWired マイコンファームウェア
...........................AWCARD_FW_Update_xxx.exe ...................................... AWCARD_FW_Update_xxx.exe
• Firmware ・ ファームウェア
Main microprocessor firmware メインマイコンファームウェア
.................................................. YSP12_xxxx.mot .......................................................................YSP12_xxxx.mot
YSP12_xxxx.id YSP12_xxxx.id
AirWired microprocessor firmware AirWired マイコンファームウェア
........................................... uaw_card_xxxx.mot ............................................................uaw_card_xxxx.mot
uaw_card_xxxx.id uaw_card_xxxx.id
• RS-232C cross cable “D-sub 9 pin female” ・ RS-232C クロスケーブル D-sub 9pin メス
T
(Specifications) （仕様）
Pin No.2 RxD Pin No.2 RxD Pin No.2 RxD Pin No.2 RxD
F
Pin No.3 TxD Pin No.3 TxD Pin No.3 TxD Pin No.3 TxD
Pin No.5 GND Pin No.5 GND Pin No.5 GND Pin No.5 GND
Pin No.7 RTS Pin No.7 RTS Pin No.7 RTS Pin No.7 RTS
A
Pin No.8 CTS Pin No.8 CTS Pin No.8 CTS Pin No.8 CTS
R
• RS-232C conversion adaptor ・ RS-232C 変換アダプター
(version 4.0, Part No.: WZ064500) （バージョン 4.0、部品番号：WZ064500）
D
● Preparation and precautions ● 準備と注意
• Download the firmware downloader program and ・ 指定のダウンロード先から、ファームウェア書き
the latest firmware from the specified download 込み用プログラムと最新のファームウェアを、PC
source to the same folder of the PC. の同じフォルダにダウンロードしてください。
• Prepare the above specified RS-232C cross cable. ・ RS-232C クロスケーブルは必ず上記仕様のものを
• While writing the firmware, keep the other application 用意してください。
software on the PC closed. ・ 書き込み時は、PC 上の他のアプリケーションソ
It is also recommended to keep the software on フトは閉じてください。
the task tray closed as well. さらに、タスクトレイ上にあるソフトも閉じてお
くことを推奨します。
44
YSP-CU4300/YSP-CU3300/NS-WSW160
Updating the main microprocessor firmware メインマイコンファームウェアのアップデート
YSP-CU4300/YSP-CU3300/
● Connection ● 接続
NS-WSW160
* Disconnect the power cable of this unit from the ※ 本機の電源コードを AC コンセントから抜きます。
AC outlet.
・ RS-232C 変換アダプターのスイッチを下記のよう
• Set the switches on RS-232C conversion adaptor に設定します。（Fig. 1）
as shown below. (Fig. 1)
DSP ucom T
ucom DSP R
RS-232C conversion adaptor
SW7
T
SW4
R RS-232C 変換アダプター
Switches Setting / スイッチ設定
T
Microprocessor type Firmware to be updated SW7 SW4
Microprocessor firmware writing mode
F
マイコンファームウェア書き込みモード
T type
Self-diagnostic function mode
ダイアグモード
A
Microprocessor firmware writing mode
マイコンファームウェア書き込みモード
R type
R
Self-diagnostic function mode
ダイアグモード
Fig. 1
D
• Connect the serial port (RS-232C) of the PC to ・ 本 機 の 書 き 込 み 用 ポ ー ト（MAIN（3）P.C.B. の
the writing port (CB205 on MAIN (3) P.C.B.) of this CB205）と PC のシリアルポート（RS-232C）を下
unit as shown below. (Fig. 2) 記のように接続します。（Fig. 2）
PC Rear view of this unit / 本機の後面
Serial port (RS-232C)
シリアルポート （RS-232C）
Writing port / 書き込みポート
(CB205 on MAIN (3) P.C.B.)
RS-232C cross cable
RS-232C クロスケーブル
RS-232C conversion adaptor
Flexible flat cable (9P)
RS-232C 変換アダプター
カード電線 （9P）
Fig. 2
45
YSP-CU4300/YSP-CU3300/NS-WSW160
● Operation procedures ● 操作方法
YSP-CU4300/YSP-CU3300/
1. Connect the power cable of this unit to the AC 1. 本機の電源コードを AC コンセントに接続します。
NS-WSW160
outlet. 本機に電源が入り、マイコンが書き込みモードに
The power to this unit is supplied and the なります。
microprocessor is in the writing mode. 2. FlashSta.exe を起動します。
2. Start up FlashSta.exe. 下記の画面が表示されます。（Fig. 3）
The screen appears as shown below. (Fig. 3) 3. 送信データ、ポートを選択します。（Fig. 3）
3. Select the data to be transmitted and port. (Fig. 3) ・ Select Program
• Select Program Internal flash memory を選択します。
Select Internal flash memory. ・ RS232C
• RS232C 接続している RS-232C ポートを選択します。
Select the port of RS-232C. ※ ポートの選択は COM1 ∼ 4 までが使用で
* For selection of the port, COM1 to 4 can きます。
be used. COM5 以上は使用できませんので、PC 側
As COM5 or higher port cannot be used, の設定で COM1 ∼ 4 を選択してください。
select out of COM 1 to 4 of the setting on
T
the PC side.
A F
Select Internal flash memory
R
Internal flash memory を選択します
D
Select the port of RS-232C
接続している RS-232C ポートを選択します
Fig. 3
46
YSP-CU4300/YSP-CU3300/NS-WSW160
4. Click [Refer...] and select the firmware name. 4. ［Refer...］をクリックし、書き込むファームウェア
YSP-CU4300/YSP-CU3300/
(Fig. 4) を選択します。（Fig. 4）
* The ID and MCU Type are loaded automatically ※ ID、および MCU Type は書き込みファイル選
NS-WSW160
when the file is selected. (Fig. 4) 択後、自動的に取り込まれます。（Fig. 4）
Click [OK]. (Fig. 4) ［OK］をクリックします。（Fig. 4）
F T
A
When [Refer...] is clicked, the “Open” screen appears
［Refer...］をクリックすると「ファイルを開く」が表示されます
R
Fig. 4
D
5. Click [Setting], and set the baud rate. (Fig. 5) 5. ［Setting］をクリックし、通信速度の設定を行い
ます。（Fig. 5）
115200
40
Fig. 5
47
YSP-CU4300/YSP-CU3300/NS-WSW160
6. Click [E.P.R.], then the “Erase” screen appears. 6. ［E.P.R］をクリックすると、「Erase」が表示されま
YSP-CU4300/YSP-CU3300/
(Fig. 6) す。（Fig. 6）
7. Click [OK] to start writing. (Fig. 6) 7. ［OK］をクリックして書き込みを開始します。
NS-WSW160
（Fig. 6）
Writing being executed.
書き込み中
F T
Fig. 6
A
8. When writing of the firmware is completed, the 8. ファームウェアの書き込みが完了すると、以下の
R
screen appears as shown below. (Fig. 7) 画面が表示されます。（Fig. 7）
Click [OK]. (Fig. 7) ［OK］をクリックします。（Fig. 7）
9. Click [Exit] to end FlashSta.exe. (Fig. 7) 9. ［Exit］をクリックして FlashSta.exe を終了します。
D
（Fig. 7）
Fig. 7
10. Disconnect the power cable of this unit from the 10. 本機の電源コードを AC コンセントから抜きます。
AC outlet. 11. 本 機 の 書 き 込 み 用 ポ ー ト（MAIN（3）P.C.B. の
11. Remove the RS-232C conversion adaptor and CB205）から RS-232C 変換アダプターとカード電
flexible flat cable from the writing port (CB205 on 線を取り外します。
MAIN (3) P.C.B.) of this unit. 12. 本機の電源コードを AC コンセントに接続してダ
12. Connect the power cable of this unit to the AC イアグを起動し、ファームウェアバージョンと
outlet, start up the self-diagnostic function and チェックサムが書き込まれたものと同じであるこ
check that the firmware version and checksum とをチェックします。（詳細は ファームウェアの
are the same as written ones. (For details, refer to バージョンとチェックサムの確認 を参照してく
“Confirmation of firmware version and checksum”) ださい。）
48
YSP-CU4300/YSP-CU3300/NS-WSW160
Updating the AirWired microprocessor firmware AirWired マイコンファームウエアのアップデート
YSP-CU4300/YSP-CU3300/
● Connection ● 接続
NS-WSW160
* Disconnect the power cable of this unit from the ※ 本機の電源コードを AC コンセントから抜きます。
AC outlet.
・ RS-232C 変換アダプターのスイッチを下記のよう
• Set the switches on RS-232C conversion adaptor に設定します。（Fig. 1）
as shown below. (Fig. 1)
DSP ucom T
ucom DSP R
RS-232C conversion adaptor
SW7
T
SW4
R RS-232C 変換アダプター
Switches Setting / スイッチ設定
T
Microprocessor type Firmware to be updated SW7 SW4
Microprocessor firmware writing mode
F
マイコンファームウェア書き込みモード
T type
Self-diagnostic function mode
ダイアグモード
A
Microprocessor firmware writing mode
マイコンファームウェア書き込みモード
R type
R
Self-diagnostic function mode
ダイアグモード
Fig. 1
D
• Connect the serial port (RS-232C) of the PC to ・ 本 機 の 書 き 込 み 用 ポ ー ト（MAIN（3）P.C.B. の
the writing port (CB205 on MAIN (3) P.C.B.) of this CB205）と PC のシリアルポート（RS-232C）を下
unit as shown below. (Fig. 2) 記のように接続します。（Fig. 2）
PC Rear view of this unit / 本機の後面
Serial port (RS-232C)
シリアルポート （RS-232C）
Writing port / 書き込みポート
(CB205 on MAIN (3) P.C.B.)
RS-232C cross cable
RS-232C クロスケーブル
RS-232C conversion adaptor
Flexible flat cable (9P)
RS-232C 変換アダプター
カード電線（9P）
Fig. 2
49
YSP-CU4300/YSP-CU3300/NS-WSW160
● Operation procedures ● 操作方法
YSP-CU4300/YSP-CU3300/
1. Connect the power cable of this unit to the AC 1. 本機の電源コードを AC コンセントに接続します。
NS-WSW160
outlet. 本機に電源が入り、マイコンが書き込みモードに
The power to this unit is supplied and the なります。
microprocessor is in the writing mode. 2. AWCARD_FW_Update_xxx.exe を起動します。
2. Start up AWCARD_FW_Update_xxx.exe. 下記の画面が表示されます。（Fig. 3）
The screen appears as shown below. (Fig. 3) 3. ポートを選択します。（Fig. 3）
3. Select the port. (Fig. 3) RS232C
RS232C 接続している RS-232C ポートを選択します。
Select the port of RS-232C. ※ ポートの選択は COM1 ∼ 4 までが使用できま
* For selection of the port, COM1 to 4 can be す。
used. COM5 以上は使用できませんので、PC 側の設
As COM5 or higher port cannot be used, select 定で COM1 ∼ 4 を選択してください。
out of COM 1 to 4 of the setting on the PC side.
F T
R A
D Fig. 3
Select the port of RS-232C
接続している RS-232C ポートを選択します
50
YSP-CU4300/YSP-CU3300/NS-WSW160
4. Click [...] and select the firmware name. (Fig. 4) 4. ［...］をクリックし、書き込むファームウェアを選
YSP-CU4300/YSP-CU3300/
択します。（Fig. 4）
* The ID and MCU Type are loaded automatically ※ ID、および MCU Type は書き込みファイル選
NS-WSW160
when the file is selected. 択後、自動的に取り込まれます。
When [...] is clicked, the “Open” screen appears
［...］をクリックすると「ファイルを開く」が
表示されます
F T
R A
D
Fig. 4
5. Click [Setting], and set the baud rate. (Fig. 5) 5. ［Setting］をクリックし、通信速度の設定を行い
ます。（Fig. 5）
Click [OK]. (Fig. 5) ［OK］をクリックします。（Fig. 5）
Click [connected]. (Fig. 5) ［connected］をクリックします。（Fig. 5）
115200
Fig. 5 51
YSP-CU4300/YSP-CU3300/NS-WSW160
6. Click [Extension] and select the update area. 6. ［Extension］をクリックし、アップデートエリア
YSP-CU4300/YSP-CU3300/
(Fig. 6) を選択します。（Fig. 6）
Click [OK]. (Fig. 6) ［OK］をクリックします。（Fig. 6）
NS-WSW160
F T
A
Fig. 6
written. (Fig. 7)
D
7. Check the firmware version and checksum
Click [Start] to start writing. (Fig. 7)
R 7. 書 き 込 ま れ る フ ァ ー ム ウ ェ ア の バ ー ジ ョ ン と
チェックサムを確認します。（Fig. 7）
［Start］をクリックして書き込みを開始します。
（Fig. 7）
Firmware version and
checksum
Fig. 7
52
YSP-CU4300/YSP-CU3300/NS-WSW160
8. When writing of the firmware is completed, “OK” is 8. ファームウェアの書き込みが完了すると、Update
YSP-CU4300/YSP-CU3300/
displayed to Update Result. (Fig. 8) Result へ OK が表示されます。（Fig. 8）
9. Click [Exit] to end AWCARD_FW_Update_xxx.exe. 9. ［Exit］をクリックして AWCARD_FW_Update_
NS-WSW160
(Fig. 8) xxx.exe を終了します。（Fig. 8）
F T
R A
Fig. 8
D
10. Disconnect the power cable of this unit from the 10. 本機の電源コードを AC コンセントから抜きます。
AC outlet. 11. 本 機 の 書 き 込 み 用 ポ ー ト（MAIN（3）P.C.B. の
11. Remove the RS-232C conversion adaptor and CB205）から RS-232C 変換アダプターとカード電
flexible flat cable from the writing port (CB205 on 線を取り外します。
MAIN (3) P.C.B.) of this unit. 12. 本機の電源コードを AC コンセントに接続してダ
12. Connect the power cable of this unit to the AC イアグを起動し、ファームウェアバージョンと
outlet, start up the self-diagnostic function and チェックサムが書き込まれたものと同じであるこ
check that the firmware version and checksum とをチェックします。（詳細は ファームウェアの
are the same as written ones. (For details, refer to バージョンとチェックサムの確認 を参照してく
“Confirmation of firmware version and checksum”) ださい。）
53
YSP-CU4300/YSP-CU3300/NS-WSW160
■ WRITING SYSTEM MODEL NAME AND DESTINATION /
システムモデル名と仕向け先の書き込み
YSP-CU4300/YSP-CU3300/
When the following parts are replaced, the system 下記の部品を交換した場合、本機が正常に動作するため
NS-WSW160
model name and the destination MUST be written to the にシステムモデル名と仕向け先を EEPROM に書き込む必
EEPROM to have proper operation. 要があります。
• DIGITAL P.C.B. ・ DIGITAL P.C.B.
• EEPROM (IC703) on DIGITAL P.C.B. ・ DIGITAL P.C.B. の EEPROM（IC703）
CAUTION: When the DIGITAL P.C.B. is replaced, the 注意： DIGITAL P.C.B. を交換した場合、ファームウェア
firmware must be updated to the latest を最新のバージョンにアップデートする必要が
version. (For details, refer to “UPDATING あります。 （詳細は ファームウェアのアップデー
FIRMWARE”) ト を参照してください。）
● Preparation ● 準備
1. Disconnect the power cable of this unit from the 1. 本機の電源コードを AC コンセントから抜きます。
T
AC outlet.
2. 以下の部品を外します。
2. Remove the following parts. (For details, refer to （詳細は 分解手順 を参照してください。）
F
“DISASSEMBLY PROCEDURES”)
・ リアカバー
• Rear cover ・ ボトムパネル
A
• Bottom panel ・ キャビネット L Ass'y
• Cabinet L assembly ・ キャビネット R Ass'y
R
• Cabinet R assembly ・ トップパネル
• Top panel ・ トップフレーム
• Top frame ・ INPUT（1）P.C.B.
D
• INPUT (1) P.C.B.
※ 分解後、外したケーブル（コネクター）をす
* Reconnect all cables (connectors) that have べて接続します。
been disconnected after disassembly.
● Operation procedure ● 操作方法
1. Connect the power cable of this unit to the AC 1. 本機の電源コードを AC コンセントに接続します。
outlet. 本機がスタンバイモードになります。
This unit is in standby mode.
2. ダイアグモードで起動します。（詳細は ダイアグ
2. Turn on power in self-diagnostic function mode. を参照してください。）
(For details, refer to “SELF-DIAGNOSTIC
3. p. SET INFORMATION メニューを選択します。
FUNCTION”)
（Fig. 1）
3. Select “p. SET INFORMATION” menu. (Fig. 1)
Main menu display Sub-menu display
メインメニュー表示 サブメニュー表示
p.SET INF p1.4300U
After a few seconds
数秒後
Fig. 1
54
YSP-CU4300/YSP-CU3300/NS-WSW160
4. Short TP731 (connected to pin 140 of IC701) of 4. DIGITAL P.C.B. の TP731（IC701 の 140 ピンと接続）
YSP-CU4300/YSP-CU3300/
DIGITAL P.C.B. and GND. (Fig. 2) と GND をショートさせます。（Fig. 2）
NS-WSW160
Short point
TP800
DGND 144 109
1
DEST WRITE 108
TP731
36 73
37 72
DGITAL P.C.B.
T DE
TP8
DG TE
ST
00
F ND
W
RI
TP7
31
R A Fig. 2
D
5. Select the destination using “ENTER” key on the 5. リモコンの 決定 キーで、仕向けを選択します。
remote control. (Fig. 3) （Fig. 3）
* If the first destination is unknown, press the ※ 最初の仕向けが不明の場合、 決定 キーを押
“ENTER” key, and the displayed destination すと J 仕向けに変化します。
will change to J destination.
Keys on the remote control / リモコンキー
p1.4300U
Every time the “ENTER” key of the remote control is pressed, the destination display
will change.
リモコンの 決定 キーを押す度に、仕向け表示が変わります。
J → U → C → G → E → B → T → A → F → K → L → V → R → H → S → J .....
4300: YSP-CU4300
3300: YSP-CU3300
Fig. 3 55
YSP-CU4300/YSP-CU3300/NS-WSW160
6. If the “RETURN” key of the remote control is 6. リモコンの 戻る キーを押すと、表示されてい
YSP-CU4300/YSP-CU3300/
pressed, the displayed destination will be written る仕向けが書き込まれ、自動的に電源が切れます。
and the power will be turned off automatically. （Fig. 4）
NS-WSW160
(Fig. 4)
※ このとき、バックアップ IC（EEPROM：DIGITAL
* At this time, initialization of the backup IC P.C.B. の IC703）の初期化は予約状態になってい
(FEPROM: IC703 of DIGITAL P.C.B.) is in the ます。
reserved state.
Keys on the remote control / リモコンキー
p1.4300U
F T
A
The displayed destination is written.
表示されている仕向けが書き込まれます。
R
Fig. 4
D
7. Be sure to return the shorted pins to their original 7. ショートしたピンを元の状態に戻します。
condition.
8. 再 び 電 源 を 入 れ、 バ ッ ク ア ッ プ IC（EEPROM：
8. Turn on the power again and initialize the backup DIGITAL P.C.B. の IC703）の初期化を行います。
IC (IC703 of EEPROM: DIGITL P.C.B.).
NOTE: The system model name and destination 注意： バックアップ IC（EEPROM：DIGITAL P.C.B. の
are preserved even when the back-up IC IC703）の初期化を行っても、システムモデ
(EEPROM IC703 of the DIGITAL P.C.B.) is ル名と仕向け先は保持されます。
initialized.
9. Start up the self-diagnostic function and select “q. 9. ダイアグを起動し、 q. CPU INFORMATION メ
CPU INFORMATION” menu. (For details, refer to ニューを選択します。
（詳細は ダイアグ を参照
“SELF-DIAGNOSTIC FUNCTION”) してください。）
Using the sub-menu, have the system model name サブメニューでシステムモデル名と仕向け先を表
and destination displayed, and check that they are 示し、正しく書き込まれていることを確認します。
written properly.
56
YSP-CU4300/YSP-CU3300/NS-WSW160
■ SELF-DIAGNOSTIC FUNCTION / ダイアグ（自己診断機能）
This unit has self-diagnostic functions that are intended 本機には、検査、測定、不良個所の発見を目的にしたダ
YSP-CU4300/YSP-CU3300/
for inspection, measurement and location of faulty point. イアグ（自己診断機能）があります。
There are 26 main menu items, each of which has sub- ダイアグには 26 個のメインメニューがあり、そのそれぞ
NS-WSW160
menu items. れにサブメニューがあります。
Listed in the table below are main menu items and sub- 下表はダイアグメニュー一覧です。
menu items.
注意： 以下のメニュー項目の一部は、このサービスマニュ
Note: Some of the menu items listed below may not apply アルに記載されているモデルに適用されない場合
to the models covered in this service manual. があります。
No. Main menu No. Sub-menu
1 DSP THROUGH 1 MASTER VOLUME 0
2 MASTER VOLUME 1
3 MASTER VOLUME 30
4 MASTER VOLUME 60
5 MASTER VOLUME 100
2 TEST SIGNAL 1 TEST ALL
2 TEST SUBWOOFER
3 TEST WOOFER L
T
4 TEST WOOFER R
5 TEST FRONT L
F
6 TEST CENTER
7 TEST SURROUND L
8 TEST FRONT R
A
9 TEST SURROUND R
3 SWEEP TEST 1 SWEEP
4 MIC CHECK 1 MIC CHECK
R
5 SPEAKER CHECK 1 ALL
2 WOOFER L
3 WOOFER R
D
5 TWEETER 1
...
...
9 TWEETER 5
a TWEETER 6
...
...
k TWEETER 16
l TWEETER 17
...
...
q TWEETER 22 (YSP-CU4300)
6 DISPLAY CHECK 1 ALL SEGMENTS ON / INDICATOR OFF
2 LATTICE PATTERN 1 / INDICATOR ON
3 LATTICE PATTERN 2 / INDICATOR ON
4 ALL SEGMENTS OFF / INDICATOR ON
7 LOOPBACK CHECK 1 RS-232C TxRx DATA
2 RS-232C HARD FLOW
3 AirWired UART
4 AirWired GPIO
5 SUBWOOFER PRE OUT
8 DEVICE CHECK 1 DEVICE CHECK
9 AD DATA CHECK 1 KEY
2 DC
3 DIGITAL AMP
4 INPUT (ANALOG)
5 DSP
6 HDMI
7 AirWired
8 USB VBUS (YSP-CU4300)
9 PRI
a PORT DETECTION 1 PORT CHECK
b EMC TEST 1 EMC TEST
(Not for service / サービスでは使用しません) 2
...
EMC PORT TEST
8
57
YSP-CU4300/YSP-CU3300/NS-WSW160
No. Main menu No. Sub-menu
YSP-CU4300/YSP-CU3300/
c PON CHECK 1 HDMI ON
2 HDMI OFF
NS-WSW160
3 AirWired ON
4 AirWired OFF
5 FL ON
6 FL OFF
7 USB ON (YSP-CU4300)
8 USB OFF (YSP-CU4300)
9 D4SPJ OFF
a IR FLASHER ON
b IR FLASHER OFF
d HDMI SELECT 1 HDMI 1
2 HDMI 2
3 HDMI 3
4 HDMI 4
e HDMI AUDIO 1 SPDIF
2 MULTI CHANNEL PCM
3 ARC
T
f USB TEST (YSP-CU4300) 1 USB TEST
g AirWired TEST 1 Tx/Rx Disable
2 Tx Enable
F
3 Rx Enable
4 Tx/Rx Enable
h SELF INSPECTION DIGITAL
A
(Not for service / サービスでは使用しません)
i SELF INSPECTION INPUT
R
(Not for service / サービスでは使用しません)
j SELF INSPECTION DIGITAL AMP
(Not for service / サービスでは使用しません)
D
k AUTO SLEEP 1 AUTO SLEEP ON
(Not for service / サービスでは使用しません) 2 AUTO SLEEP OFF
l PROTECTION HISTORY 1 HISTORY 1
2 HISTORY 2
3 HISTORY 3
4 HISTORY 4
5 RESET HISTORY
m POWER OFF FACTOR HISTORY 1 HISTORY 1
2 HISTORY 2
3 HISTORY 3
4 HISTORY 4
5 HISTORY 5
6 HISTORY 6
7 HISTORY 7
8 HISTORY 8
9 RESET HISTORY
n RS-232C DBG 1 CI
(Not for service / サービスでは使用しません) 2 MAIN
3 VIDEO
4 SiI
o FACTORY PRESET 1 INHIBIT
2 RESERVE
p SET INFORMATION 1 SYSTEM MODEL NAME/DESTINATION
2 FIRMWARE VERSION
q MICROPROCESSOR INFORMATION 1 MICROPROCESSOR VERSION
2 MICROPROCESSOR CHECKSUM
3 DSP VERSION
4 DSP CHECKSUM
5 HDMI/OSD VERSION
6 AirWired VERSION
7 USB HOST VERSION (YSP-CU4300)
58
YSP-CU4300/YSP-CU3300/NS-WSW160
● Starting Self-Diagnostic Function ● ダイアグの起動
YSP-CU4300/YSP-CU3300/
With this unit in the stand-by mode, press the keys on the スタンバイモードで、リモコンキーを下記の順に押しま
NS-WSW160
remote control in the order as shown below. す。
The self-diagnostic function mode is activated. ダイアグが起動します。
Keys on the remote control / リモコンキー
F T 2
R A
1
D
Display / 表示
Opening message / オープニング表示 Sub-menu display
(Main menu / メインメニュー) サブメニュー表示
After a few seconds
数秒後
59
YSP-CU4300/YSP-CU3300/NS-WSW160
● Starting Self-Diagnostic Function in ● プロテクション解除モードでの起動
YSP-CU4300/YSP-CU3300/
the protection cancel mode
NS-WSW160
If the protection function works and causes hindrance プロテクションが動作することにより、故障箇所の診断
to troubleshooting, cancel the protection function by the に支障をきたすような場合は、次の方法によりプロテク
procedure below, and it will be possible to enter the self- ションを解除した状態でダイアグモードに入ることがで
diagnostic function mode. きます。
With this unit in the stand-by mode, press the keys on the スタンバイ状態で、リモコンキーを下記の順に押します。
remote control in the order as shown below.
プロテクション解除モードでダイアグが起動します。
The self-diagnostic function mode is activated with the
protection functions disabled.
Keys on the remote control / リモコンキー
T
3
A F
D R Display / 表示
2
1
Opening message / オープニング表示 Sub-menu display
(Main menu / メインメニュー) サブメニュー表示
After a few seconds
数秒後
For details of protection functions, refer to “l. PROTECTION プロテクションの詳細は、 l. PROTECTION HISTORY メ
HISTORY” menu. ニューを参照してください。
CAUTION! 注意！
Using this product with the protection function disabled プロテクションを解除した状態でのダイアグモードは、
may cause further damage to this unit. Use special care 危険な状態でもプロテクションが作動しないため、動作
for this point when using this mode. させると、本機を破壊することがあります。このモード
を使用する場合は十分注意してください。
60
YSP-CU4300/YSP-CU3300/NS-WSW160
● Canceling Self-Diagnostic Function ● ダイアグの解除
YSP-CU4300/YSP-CU3300/
1. Before canceling self-diagnostic function, execute 1. ダイアグを解除する前に、 o. FACTORY PRESET メ
NS-WSW160
setting for “o. FACTORY PRESET” menu. (Memory ニュー（メモリーの初期化禁止／またはメモリーの
initialization inhibited or Memory initialized). 初期化）の設定をします。
* In order to keep the user memory preserved, be ※ ユ ー ザ ー メ モ リ ー を 保 持 し た い 場 合 は、 必 ず
sure to select PRESET INHIBIT (Memory initialization PRESET INHIBIT（メモリー初期化禁止）を選択し
inhibited). てください。
2. Press the “ ” (Power) key to turn off the power. 2. （電源）キーを押して電源を切ります。
● Display provided when Self-Diagnostic ● ダイアグ起動時の表示
Function started
The display is as described below depending on the 最後に本機の電源が切れたときの状況により、下記のよ
situation the last time the power to this unit is turned off. うに表示されます。
T
When there is no history of protection function: プロテクション履歴がない場合：
“1. DSP THR” is displayed. “11. VOL 0” menu is displayed 1. DSP THR が表示されます。数秒後、11. VOL 0 メニュー
F
in a few seconds. が表示されます。
A
Display / 表示
Opening message / オープニング表示 Sub-menu display
R
(Main menu / メインメニュー) サブメニュー表示
D
After a few seconds
数秒後
When there is a history of protection function: プロテクション履歴がある場合：
The data of protection function which worked at the moment そのときに働いたプロテクションの情報が 1 秒間表示さ
is displayed for one second, and then the power is turned れた後、電源がオフになります。
off.
Display / 表示
Opening message / オープニング表示 Power is turned off
(Protection function / プロテクション情報) 電源オフ
After one second
1 秒後
For details of protection functions, refer to “l. PROTECTION プロテクションの詳細は、 l. PROTECTION HISTORY メ
HISTORY” menu. ニューを参照してください。
61
YSP-CU4300/YSP-CU3300/NS-WSW160
● History of protection function ● プロテクションの履歴
YSP-CU4300/YSP-CU3300/
When the protection function has worked, its history プロテクションが働いた場合、その履歴はバックアッ
NS-WSW160
is stored in memory as backup data. プデータとしてメモリーに保存されます。
Even if no abnormality is noted while servicing the unit, 修理のときに異常が認められなくても、バックアッ
an abnormality which has occurred previously can be プデータが残っていれば、お客様のところで起きた
defined as long as the backup data has been stored. 異常を区別できます。
The history of the protection function will be initialized o. PRESET RESERVE （メモリーの初期化）、または I5.
when self-diagnostic function is cancelled by HISTORY RESET （履歴消去）メニューを選んでダイ
selecting “o. PRESET RESERVE” (Memory initialized) アグを解除した場合、プロテクションの履歴は初期
/ “l5. HISTORY RESET” menu. 化されます。
● Operation procedure of Main menu ● メインメニューとサブメニューの操作
T
and Sub-menu
There are 26 main menu items, each of which has sub- ダイアグには 26 のメインメニューがあり、そのそれぞれ
F
menu items. にサブメニューがあります。
Main menu selection メインメニューの選択
A
Select the main menu using “ ” (Forward) and “ ” リモコンの （順送り）、 （逆送り）キーで選択
(Reverse) keys on the remote control. します。
R
Sub-menu selection サブメニューの選択
Select the sub-menu using “ ” (Forward) and “ ” リモコンの （順送り）、 （逆送り）キーで選択します。
D
(Reverse) keys on the remote control.
Key on the remote control / リモコンキー
" " (Forward) key
" "（順送り）キー " " (Forward) key
" "（順送り）キー
Main menu selection Sub-menu selection
メインメニューの選択 サブメニューの選択
" " (Reverse) key
" " (Reverse) key " "（逆送り）キー
" "（逆送り）キー
62
YSP-CU4300/YSP-CU3300/NS-WSW160
● Functions in Self-Diagnostic Function ● ダイアグ中の機能
YSP-CU4300/YSP-CU3300/
mode
NS-WSW160
In addition to the self-diagnostic function menu items, ダイアグメニューの他に、以下の機能が動作します。
functions as listed below are available.
・ 電源 オフ
• Power OFF ・ インプット切替
• Input selection ・ マスター音量
• Master volume
● Initial settings when Self-Diagnostic ● ダイアグ開始時の初期設定
Function started
The following initial settings are used when starting self- ダイアグ開始時に以下のような設定になります。
diagnostic function. ダイアグ解除時にはダイアグ開始前の状態に戻ります。
When self-diagnostic function is canceled, these settings
・ インプット： ANALOG
T
are restored to those before starting self-diagnostic
function. ・ マスター音量： １（0 ∼ 50）
F
・ サブウーファー音量： 0（± 6）
• INPUT: ANALOG
・ IR パススルー： オン
• Master volume: 1 (0 to 50)
A
・ AirWired 電源： OFF
• Subwoofer volume: 0 (±6)
• IR Pass Through: ON
R
• AirWired Power: OFF
63
YSP-CU4300/YSP-CU3300/NS-WSW160
● Details of Self-Diagnostic Function menu ● ダイアグメニュー詳細
YSP-CU4300/YSP-CU3300/
1. DSP THROUGH 1. DSP THROUGH
NS-WSW160
This menu is used to select the volume level. ボリュームレベルを選択します。
The signal is output in digital full bit without including ヘッドマージンを含まず、デジタルフルビットで出
the head margin. 力されます。
Using the input key, select the input source. (Default INPUT キーで入力ソースを切り替えます。
（デフォル
set : ANALOG input). ト設定：ANALOG 入力）
* When the multi-channel signal is input, the ※ マルチチャンネル信号が入力された場合、サラウ
surround L/R is not output. ンド L/R は出力されません。
* When the 2-channel stereo signal is input, the L ※ 2ch ステレオ信号が入力された場合、L チャンネ
channel signal is output to center and subwoofer ルの信号がセンターとサブウーファー出力に出力
outputs. されます。
1-1. MASTER VOLUME 0 (Mute)
11.VOL 0
F T
1-2. MASTER VOLUME 1 (-96.5 dB minimum volume)
12.VOL 1
R A
1-3. MASTER VOLUME 30 (-40 dB)
13.VOL 30
D
1-4. MASTER VOLUME 60 (-20 dB)
14.VOL 60
1-5. MASTER VOLUME 100 (0 dB maximum volume)
15.VOL 100
64
YSP-CU4300/YSP-CU3300/NS-WSW160
2. TEST SIGNAL 2. TEST SIGNAL
YSP-CU4300/YSP-CU3300/
* When this menu is selected, the master volume ※ このメニューを選択すると、マスター音量レベル
NS-WSW160
level is raised up automatically. が自動的に上がります。
The built-in noise generator of DSP outputs the test DSP 内蔵のノイズ発生回路によって、サブメニュー
noise through the channels specified by using the で指定したチャンネルへテストノイズが出力されま
sub-menu. す。
2-1. TEST ALL
21.TES ALL
The test noise is output to all channel.
テストノイズが全てのチャンネルへ出力されます。
Master volume level: 60 (-20 dB)
2-2. TEST SUBWOOFER
22.TS SW
The test noise is output to SUBWOOFER channel.
テストノイズが SUBWOOFER チャンネルへ出力されます。
T
Master volume level: 100 (0 dB maximum volume)
F
2-3. TEST WOOFER L
23.TS WL
The test noise is output to WOOFER L channel.
テストノイズが WOOFER L チャンネルへ出力されます。
A
Master volume level: 62
R
2-4. TEST WOOFER R
24.TS WR
The test noise is output to WOOFER R channel.
テストノイズが WOOFER R チャンネルへ出力されます。
D
Master volume level: 62
2-5. TEST FRONT L
25.TS FL
The test noise from FRONT L is output to tweeter A0.
FRONT L から出力されるテストノイズが、ツイーター A0 へ出力されます。
Master volume level: 92
2-6. TEST CENTER
26.TS CT
The test noise from CENTER is output to tweeter A1.
CENTER から出力されるテストノイズが、ツイーター A1 へ出力されます。
Master volume level: 92
2-7. TEST SURROUND L
27.TS SL
The test noise from SURROUND L is output to tweeter A2.
SURROUND L から出力されるテストノイズが、ツイーター A2 へ出力されます。
Master volume level: 92
2-8. TEST FRONT R
28.TS FR
The test noise from FRONT R is output to tweeter A3.
FRONT R から出力されるテストノイズが、ツイーター A3 へ出力されます。
Master volume level: 92
2-9. TEST SURROUND R
29.TS SR
The test noise from SURROUND R is output to tweeter A4.
SURROUND R から出力されるテストノイズが、ツイーター A4 へ出力されます。
Master volume level: 92
65
YSP-CU4300/YSP-CU3300/NS-WSW160
3. SWEEP TEST 3. SWEEP TEST
YSP-CU4300/YSP-CU3300/
* When this menu is selected, the volume level is ※ このメニューを選択すると、出力レベルが自動的
raised up to 52 (-8.0) automatically. に 52（-8.0）に上がります。
NS-WSW160
Input the sweep signal (20 Hz to 2 kHz, 450 mVrms, アナログ入力端子へスイープ信号（20 Hz ∼ 2 kHz、
sweep time 2 sec) to the ANALOG INPUT terminal, 450mVrms、スイープタイム 2 秒）を入力し、出力音
and listen to the output sound very carefully. Check を注意深く聴いて本機にビリ付きや異音等がないこ
that the rattling and/or abnormal sound can not be とを確認します。
heard.
3.SWEEP
4. MIC CHECK 4. MIC CHECK
The signals input through the IntelliBeam microphone インテリビームマイクに入力された信号が A/D − D/A
are output to all channels via A/D-D/A. 経由で全てのチャンネルへ出力されます。
F T
4.MIC CHK
A
5. SPEAKER CHECK 5. SPEAKER CHECK
* When this menu is selected, the master volume ※ このメニューを選択すると、マスター音量レベル
R
level is raised up automatically. が自動的に上がります。
The built-in noise generator of DSP outputs the test DSP 内蔵のノイズ発生回路によって、サブメニュー
D
noise (pink noise) through the speakers specified by で指定したスピーカーへテストノイズ（ピンクノイ
using the sub-menu. ズ）が出力されます。
5-1. ALL
51.ALL
The test noise is output to all speaker.
テストノイズが全てのスピーカーへ出力されます。
Master volume level: 40
5-2. WOOFER L
52.WF L
The test noise is output to WOOFER L.
テストノイズが WOOFER L へ出力されます。
Master volume level: 60
5-3. WOOFER R
53.WF R
The test noise is output to WOOFER R.
テストノイズが WOOFER R へ出力されます。
Master volume level: 60
5-5. to 5-9. TWEETER 1 to 5
55.TW 1
The test noise is output to TWEETER 1 to 5.
テストノイズが TWEETER 1 ∼ 5 へ出力されます。
Master volume level: Max.
5-a. to 5-q. TWEETER 6 to 22
5a.TW 6
The test noise is output to TWEETER 6 to 22 (YSP-CU4300) / 6 to 16 (YSP-CU3300).
テストノイズが TWEETER 6 ∼ 22（YSP-CU4300）／ 6 ∼ 16（YSP-CU3300）へ出力されます。
Master volume level: Max.
66
YSP-CU4300/YSP-CU3300/NS-WSW160
6. FL DISPLAY CHECK 6. FL DISPLAY CHECK
YSP-CU4300/YSP-CU3300/
This menu is used to check operations of the FL display FL 表示とインジケーターの動作を確認します。
and indicators.
NS-WSW160
サブメニュー操作により、表示状態が以下のように
Using the sub-menu, the display condition changes 変わります。
as shown below.
FL display and indicators / FL 表示とインジケーター
Initial display / 初期表示
T
6-1. ALL SEGMENTS ON / 全セグメント点灯
F
STATUS indicator: Off
STATUS インジケーター：消灯
* After check, change to next menu at once.
A
確認後、速やかに次のメニューに変えてください。
D R 6-2. LATTICE PATTERN 1 / 格子状点灯 1
STATUS indicator: Lights (Green)
STATUS インジケーター：点灯（緑）
6-3. LATTICE PATTERN 2 / 格子状点灯 2
SURROUND indicator: Lights (Orange)
SURROUND インジケーター：点灯（橙）
6-4. ALL SEGMENTS OFF / 全セグメント消灯
SURROUND indicator: Lights (Blue)
SURROUND インジケーター：点灯（青）
67
YSP-CU4300/YSP-CU3300/NS-WSW160
7. LOOPBACK CHECK 7. LOOPBACK CHECK
YSP-CU4300/YSP-CU3300/
Loop back check of RS-232C, AirWired and subwoofer. RS-232C、AirWired、サブウーファーのループバック
チェックをします。
NS-WSW160
7-1. RS-232C TxRx DATA
Transmission and reception of the RS-232C 7-1. RS-232C TxRx DATA
data are checked. RS-232C データの送受信チェックを行います。
71.232D:OK
OK: Normal / 正常
NG: Abnormal / 異常
– –: Checking / チェック中
7-2. RS-232C HARD FLOW 7-2. RS-232C HARD FLOW
Operation of the RS-232C flow port of the RS-232C ハードウェアフローポートの動作
hardware is checked. チェックを行います。
T
72.232H:OK
F
OK: Normal / 正常
NG: Abnormal / 異常
A
– –: Checking / チェック中
R
7-3. AirWired UART 7-3. AirWired UART
Transmission and reception of the AirWired AirWired データの送受信チェックを行います。
D
data are checked.
73.AW D:OK
OK: Normal / 正常
NG: Abnormal / 異常
– –: Checking / チェック中
7-4. AirWired GPIO 7-4. AirWired GPIO
Operation of the AirWired GPIO port is AirWired GPIO ポートの動作チェックを行いま
checked. す。
74.AW G:OK
OK: Normal / 正常
NG: Abnormal / 異常
– –: Checking / チェック中
7-5. SUBWOOFER PRE OUT 7-5. SUBWOOFER PRE OUT
PRE OUT of subwoofer is checked. サブウーファー PRE OUT のチェックを行いま
It connects with analog input Lch and detects す。
signal in DIR (Sin wave of about 150 Hz). PRE OUT をアナログ入力 Lch に接続し、DIR
で検出します。（約 150 Hz の Sin 波）
75.SWPO:OK
OK: Normal / 正常
NG: Abnormal / 異常
– –: Checking / チェック中
68
YSP-CU4300/YSP-CU3300/NS-WSW160
8. DEVICE CHECK 8. DEVICE CHECK
YSP-CU4300/YSP-CU3300/
This menu is used to check the communication and 各デバイス間の通信とバスラインの接続をチェック
bus line connection between devices. します。
NS-WSW160
The check is executed automatically. When an error チェックは自動的に実行されます。エラーが検出さ
is detected, the corresponding error message is れると、対応するエラーメッセージが下記のように
displayed as shown below. 表示されます。
Error detection of EEPROM (IC703)
ERR EEPROM
EEPROM（IC703）に不具合がある場合
Error detection of DSP (IC501) / SDRAM (IC502)
ERR DSP
DSP（IC501）/ SDRAM（IC502）に不具合がある場合
Error detection of D4SPJ A (IC905) / B (IC909) / C (IC911, YSP-CU4300)
ERR D4SPJx
D4SPJ A（IC905）／ B（IC909）／ C（IC911、YSP-CU4300）に不具合がある場合
Error detection of USB HOST decoder (IC302) (YSP-CU4300)
ERR USB
USB HOST デコーダー（IC302）に不具合がある場合 （YSP-CU4300）
T
Error detection of Apple authentication IC (IC305) (YSP-CU4300)
ERR APPLE
Apple 認証 IC（IC305）に不具合がある場合 （YSP-CU4300）
F
Error detection of PWM processor (IC916) for digital amplifier.
ERR DAMP
デジタルアンプ用 PWM プロセッサー（IC916）に不具合がある場合
A
Error detection of HDMI/OSD port processor (IC101).
ERR HDMI
HDMI/OSD ポートプロセッサー（IC101）に不具合がある場合
R
Error detection of OSD flash ROM (IC102).
ERR OFLASH
OSD flash ROM（IC102）に不具合がある場合
Error detection of TUNER (YSP-CU4300)
D
ERR TUNER
チューナーに不具合がある場合 （YSP-CU4300）
Error detection of PRI port (IC701, 142 pin)
ERR PRI
PRI（IC701、142 ピン）ポートに不具合がある場合
No error detected
NO ERROR
不具合がない場合
IC102 IC101 IC305
HDMI/OSD Apple
FLASH ROM
PORT PROCESSOR AUTHENTICATION IC
16Mbit
SII9573CTUC SIL9134
IC703 IC701 IC501 IC302
EEPROM MICROPROCESSOR USB HOST DECODER
R1EX25032ASA00A TMPM362F10FG BU94607ARKV-E2
PRI port (26V_PRI)
142
DSP
D81Y IC502
IC916
SDRAM
PWM PROCESSOR 64Mbit
TAS5086DBT TUNER
IC905
Power supply voltage DIGITAL AMPLIFIER – A
YDA141-SZ IC909
DIGITAL AMPLIFIER – B
IC911 YDA141-SZ
DIGITAL AMPLIFIER – C
YDA141-SZ
: YSP-CU4300
69
YSP-CU4300/YSP-CU3300/NS-WSW160
9. AD DATA CHECK 9. AD DATA CHECK
YSP-CU4300/YSP-CU3300/
This menu is used to display the A/D conversion パネルキー、プロテクションなどを検出しているマ
value of the microprocessor which detects panel keys イコンの A/D 変換の値を、サブメニューで表示しま
NS-WSW160
and protection functions by using the sub-menu. す。
9-1. KEY 9-1. KEY
KEY: The voltage at 131 pin (KEY1) of KEY： マイコン（IC701）の 131 ピン（KEY1）
microprocessor IC701 is displayed. の電圧値を表示します。
(Reference voltage: 3.3 V = 255) （基準電圧：3.3 V = 255）
91.KEY:255
Key destination for A/D port
Key input (A/D) pull-up resistance 10 k-ohms
Display / 表示 0 – 15 95 – 115 180 – 200
T
Key name / キー名称 VOLUME + VOLUME - INPUT
F
9-2. DC 9-2. DC
A
DC voltage protection value of speaker output スピーカ出力 DC 電圧の値
R
DC: Center channel DC： センターチャンネル
Normal value: 105 to 150 正常値：105 ∼ 150
(Reference voltage: 3.3 V = 255) （基準電圧：3.3 V = 255）
D
* If DC becomes out of the normal value range, ※ DC が正常値を外れるとプロテクションが
the protection function works to turn off the 働き、電源が切れます。
power.
92.DC :124
9-3. DIGITAL AMP 9-3. DIGITAL AMP
DMP: Power supply voltage +26D, +5VP_A, DMP：電源電圧 +26D、+5VP_A、+3.3D
+3.3D 正常値：48 ∼ 143
Normal value: 48 to 143 （基準電圧：3.3 V = 255）
(Reference voltage: 3.3 V = 255)
※ DMP が正常値を外れるとプロテクションが
* If DMP becomes out of the normal value 働き、電源が切れます。
range, the protection function works to turn
off the power.
93.DMP:114
70
YSP-CU4300/YSP-CU3300/NS-WSW160
9-4. INPUT (ANALOG) 9-4. INPUT（ANALOG）
YSP-CU4300/YSP-CU3300/
INP: Power supply voltage +12A, +5A, FL, VP INP： 電源電圧 +12A、+5A、FL、VP
NS-WSW160
Normal value: 97 to 147 正常値：97 ∼ 147
(Power is turned on/ （電源オン／ iPod 充電中）
Charged iPod) 29 ∼ 64（iPod スタンバイ）
29 to 64 (iPod standby) （基準電圧：3.3 V = 255）
(Reference voltage: 3.3V=255)
※ INPUT が正常値を外れるとプロテクション
* If INPUT becomes out of the normal value が働き、電源が切れます。
range, the protection function works to turn
off the power.
94.INP:207
9-5. DSP 9-5. DSP
T
DSP: Power supply voltage +3.3DSP, +1.2DSP DSP： 電源電圧 +3.3DSP、+1.2DSP
F
Normal value: 82 to 139 正常値：82 ∼ 139
(Reference voltage: 3.3V=255) （基準電圧：3.3 V = 255）
A
* If DSP becomes out of the normal value ※ DSP が正常値を外れるとプロテクションが
range, the protection function works to turn 働き、電源が切れます。
R
off the power.
D
95.DSP:134
9-6. HDMI 9-6. HDMI
HDM: Power supply voltage +5.0H, +3.3H, HDM：電源電圧 +5.0H、+3.3H、+1.3H
+1.3H 正常値：102 ∼ 137
Normal value: 102 to 137 （基準電圧：3.3 V = 255）
(Reference voltage: 3.3V=255)
※ HDMI が正常値を外れるとプロテクション
* If HDMI becomes out of the normal value が働き、電源が切れます。
range, the protection function works to turn
off the power.
96.HDM:180
9-7. AirWired 9-7. AirWired
AW: Power supply voltage +5AIR AW： 電源電圧 +5AIR
Normal value: 102 to 137 正常値：102 ∼ 137
(Reference voltage: 3.3V=255) （基準電圧：3.3 V = 255）
* If AW becomes out of the normal value range, ※ AW が正常値を外れるとプロテクションが
the protection function works to turn off the 働き、電源が切れます。
power.
97.AW :000
71
YSP-CU4300/YSP-CU3300/NS-WSW160
9-8. USB 9-8. USB
YSP-CU4300/YSP-CU3300/
VBU: Power supply voltage USB_VBUS VBU： 電源電圧 USB_VBUS
NS-WSW160
Normal value: 94 to 178 正常値：94 ∼ 178
(Reference voltage: 3.3V=255) （基準電圧：3.3 V = 255）
* If VBU becomes out of the normal value ※ VBU が正常値を外れるとプロテクションが
range, the protection function works to turn 働き、電源が切れます。
off the power.
98.VBU:098
9-9. PRI 9-9. PRI
Overcurrent detection to digital amplifier デジタルアンプへの過電流の検出
PRI: Power supply voltage +26V PRI： 電源電圧 +26V
T
Normal value: 169 to 255 正常値：169 ∼ 255
(Reference voltage: 3.3 V = 255) （基準電圧：3.3 V = 255）
F
* If PRI becomes out of the normal value ※ PRI が正常値を外れるとプロテクションが
range, the protection function works to turn 働き、電源が切れます。
A
off the power.
R
99.PRI:049
a. PORT DETECTION
D
This menu is used to check the input port.
DETECT OK
a. PORT DETECTION
入力ポートをチェックします。
OK: No error detection / エラー検出なし
NG: An error is detected / 不良検出あり
– –: Checking / チェック中
b. EMC TEST b. EMC TEST
Not for service. サービスでは使用しません。
b1.TEST D4_PON H
72
YSP-CU4300/YSP-CU3300/NS-WSW160
c. PON CHECK c. PON CHECK
YSP-CU4300/YSP-CU3300/
This menu is used to check the power supply control. 電源制御をチェックします。
NS-WSW160
c-1. HDMI ON
c1.HON OK
The HDMI power supply control is set to ON.
HDMI 電源コントロールが ON に設定されます。
HDMI_PON1 (107 pin) : +3.3H on
HDMI_PON2 (108 pin) : +5H on
HDMI_PON3 (109 pin) : +1.2H on
c-2. HDMI OFF
c2.HOFF OK
The HDMI power supply control is set to OFF.
HDMI 電源コントロールが OFF に設定されます。
HDMI_PON1 (107 pin) : +3.3H on
HDMI_PON2 (108 pin) : +5H on
HDMI_PON3 (109 pin) : +1.2H on
c-3. AirWired ON
T
c3.AON OK
The AirWired power supply control is set to ON.
AirWired 電源コントロールが ON に設定されます。
F
AW_PON (104 pin) : S3.3_AW on
c-4. AirWired OFF
c4.AOFF OK
A
The AirWired power supply control is set to OFF.
AirWired 電源コントロールが OFF に設定されます。
AW_PON (104 pin) : S3.3_AW on
R
c-5. FL ON
c5.FON OK
The FL power supply control is set to ON.
D
FL 電源コントロールが ON に設定されます。
FL_PON (73 pin) : +12D on
c-6. FL OFF
The FL power supply control is set to OFF.
FL 電源コントロールが OFF に設定されます。
FL_PON (73 pin) : +12D on
c-7. USB ON (YSP-CU4300)
c7.UON OK
The USB power supply control is set to ON.
USB 電源コントロールが ON に設定されます。
USB_PON (97 pin) : VBUS on
c-8. USB OFF (YSP-CU4300)
c8.UOFF OK
The USB power supply control is set to OFF.
USB 電源コントロールが OFF に設定されます。
USB_PON (97 pin) : VBUS on
c-9. DAMP OFF
c9.DOFF OK
The DAMP power supply control is set to OFF.
DAMP 電源コントロールが OFF に設定されます。
D4_PON (22 pin) : DGND on
c-a. IR FLASHER ON
ca.RON OK
The IR FLASHER power supply control is set to ON.
IR FLASHER 電源コントロールが ON に設定されます。
FLASHER_PON (86 pin) : +12IR on
c-b. IR FLASHER OFF
cv.ROFF OK
The IR FLASHER power supply control is set to OFF.
IR FLASHER 電源コントロールが OFF に設定されます。
FLASHER_PON (86 pin) : +12IR on
73
YSP-CU4300/YSP-CU3300/NS-WSW160
d. HDMI SELECT d. HDMI SELECT
YSP-CU4300/YSP-CU3300/
* When this menu is selected, the volume level is ※ このメニューを選択すると、出力レベルが自動的
raised up to 60 (-4.0) automatically. に 30（-19.0）に上がります。
NS-WSW160
This menu is used to display the information of the HDMI 入力信号の情報を表示します。
HDMI input signal. このメニューを選択すると入力ソースは HDMI 1 に切
When this menu is selected, the input source is り替わります。
changed to HDMI 1.
d.1_******
The number of output channels is displayed.
出力チャンネル数が表示されます。
2.0 (20) / 5.1 (51) / 7.1 (71)
The resolution is displayed.
解像度が表示されます。
108i / 108p / 480p / 480i / 720p / 576p / 576i / 4k2k / 3D
T
The selected HDIMI IN number (1/2/3/4) is displayed.
選択された HDMI IN（1/2/3/4）が表示されます。
A F
R
e. HDMI AUDIO e. HDMI AUDIO
This menu is used to check the route of audio signal HDMI IN/OUT に入力されたオーディオ信号の経路を
input to HDMI IN/OUT. チェックします。
D
* Before check using “e-3. ARC” menu, be sure to ※ e-3. ARC メニューでのチェックの前に、あらか
connect a TV monitor equipped with Audio Return じめ必ず Audio Return Channel 機能に対応してい
Channel function to this unit in advance. るテレビを接続してください。
e-1. SPDIF
e1.SPDIF
SPDIF signal is output.
SPDIF 信号が出力されます。
e-2. MULTI CH PCM
e2.MPCM
Multi channel PCM signal is output.
Multi channel PCM 信号が出力されます。
e-3. ARC (Audio Return Channel function)
e3.ARC
The audio signal input from HDMI OUT is output.
HDMI OUT から入力された音声信号が出力されます。
f. USB TEST (YSP-CU4300) f. USB TEST（YSP-CU4300）
This menu is used to check connection of USB. USB の接続をチェックします。
The 1st music file stored in the USB storage device USB 端子に接続された USB フラッシュメモリーの音
connected to the USB port is reproduced. 楽ファイルの 1 曲目が再生されます。
* Copy 2 or more music files from PC to the root ※ あらかじめ PC から USB フラッシュメモリーの
folder of the USB storage device in advance. ルートフォルダに音楽ファイルを 2 曲以上コピー
してください。
f.USB TEST
74
YSP-CU4300/YSP-CU3300/NS-WSW160
g. AirWired TEST g. AirWired TEST
YSP-CU4300/YSP-CU3300/
This menu is used to setup of AirWired Rx/Tx Enable AirWired Rx/Tx Enable ポートの設定を行います。
port.
NS-WSW160
g-1. AirWired DISABLE
g1.AW DIS
Both Rx/Tx (Receiver/Transmitter) are disable.
Rx/Tx（送受信）を無効にします。
g-2. AirWired Tx ENABLE
g2.AW TxEN
Tx (Transmitter) is enable.
Tx（送信）を有効にします。
g-3. AirWired Rx ENABLE
g3.AW RxEN
Rx (Receiver) is enable.
Rx（受信）を有効にします。
T
g-4. AirWired Rx/Tx ENABLE
g4.AW EN
F
Both Rx/Tx (Receiver/Transmitter) are enable.
Rx/Tx（送受信）を有効にします。
h. SELF INSPECTION DIGITAL
R A h. SELF INSPECTION DIGITAL
D
Not for service. サービスでは使用しません。
f.USB TEST
i. SELF INSPECTION INPUT i. SELF INSPECTION INPUT
Not for service. サービスでは使用しません。
f.USB TEST
j. SELF INSPECTION DAMP j. SELF INSPECTION DAMP
Not for service. サービスでは使用しません。
f.USB TEST
k. AUTO SLEEP k. AUTO SLEEP
Not for service. サービスでは使用しません。
k.SLP ON
75
YSP-CU4300/YSP-CU3300/NS-WSW160
l. PROTECTION HISTORY l. PROTECTION HISTORY
YSP-CU4300/YSP-CU3300/
This menu is used to display the history of protection プロテクション履歴が表示されます。
function.
NS-WSW160
※ 図中の数値は参考例です。
* Numeric values in the figure are given as reference
only.
l-1. History 1 / 履歴 1
l1.No PRT
l-2. History 2 / 履歴 2
l2.No PRT
l-3. History 3 / 履歴 3
l3.No PRT
l-4. History 4 / 履歴 4
l4.No PRT
T
l-5. HISTORY RESET / 履歴消去
l5.RESET
Select this menu and press the “ENTER” key on the remote control. The protection history will be
F
initialized.
本メニュー選択後、リモコンの ENTER キーを押すとプロテクション履歴が消去されます。
A
History of protection function is displayed as shown プロテクション履歴は下記のように表示されます。
R
below.
Digital amplifier shut-down and over-temperature detection / デジタルアンプ シャットダウン、過熱検出
lx.TIWxxxH
H: Displayed when the voltage is HIGHER than upper limit. / 電圧が上限値より高い場合に表示されます
D
L: Displayed when the voltage is LOWER than lower limit. / 電圧が下限値より低い場合に表示されます
xxx: A/D conversion value of voltage at the moment when the protection function worked.
プロテクションが働いた瞬間の電圧の A/D 変換値
D4SPJ over-current and over-temperature detection
lx.D4WxxxH
D4SPJ 過電流、過熱検出
DC voltage protection value of speaker output detection
lx.DCxxxH
スピーカ出力 DC 電圧検出
Digital amplifier power supply voltage protection detection (+26D, +5VP_A, +3.3D)
lx.AMPxxxH
デジタルアンプ電源電圧プロテクションの検出（+26D、+5VP_A、+3.3D）
Analog power supply voltage protection detection (+12A, +5A, FL, VP)
lx.INPxxxH
アナログ電源電圧プロテクションの検出（+12A、+5A、FL、VP）
DSP power supply voltage protection detection (+3.3DSP, +1.2DSP)
lx.DSPxxxH
DSP 電源電圧プロテクションの検出（+3.3DSP、+1.2DSP）
HDMI power supply voltage protection detection (+5H, +3.3H, +1.3H)
lx.HDMxxxH
HDMI 電源電圧プロテクションの検出（+5H、+3.3H、+1.3H）
AirWired power supply voltage protection detection (+5AIR)
lx.AWxxxH
AirWired 電源電圧プロテクションの検出（+5AIR）
USB power supply voltage protection detection (USB_VBUS) (YSP-CU4300)
lx.VBUxxxH
USB 電源電圧プロテクションの検出（USB_VBUS） （YSP-CU4300）
Over-current detection (+26V)
lx.26VxxxH
過電流検出（+26V）
USB power supply voltage and over-current protection detection (USB_VBUS) (YSP-CU4300)
lx.USIxxxH
USB 電源電圧、過電流プロテクションの検出（USB_VBUS） （YSP-CU4300）
No error detection.
lx.No PRT
検出なし
76
YSP-CU4300/YSP-CU3300/NS-WSW160
m. POWER OFF FACTOR HISTORY m. POWER OFF FACTOR HISTORY
YSP-CU4300/YSP-CU3300/
This menu is used to display the history of power-off 電源オフ要因履歴が表示されます。
factor.
NS-WSW160
※ 図中の数値は参考例です。
* Numeric values in the figure are given as reference
only.
m-1. History 1 / 履歴 1
m1.NO OFF
m-2. History 2 / 履歴 2
m2.NO OFF
m-3. History 3 / 履歴 3
m3.NO OFF
m-4. History 4 / 履歴 4
m4.NO OFF
T
m-5. History 5 / 履歴 5
m5.NO OFF
F
m-6. History 6 / 履歴 6
m6.NO OFF
A
m-7. History 7 / 履歴 7
m7.NO OFF
R
m-8. History 8 / 履歴 8
m8.NO OFF
D
m-9. HISTORY RESET / 履歴消去
m9.RESET
Select this menu and press the “ENTER” key on the remote control. The history of power-off factor will be
initialized.
本メニュー選択後、リモコンの ENTER キーを押すと電源オフ要因履歴が消去されます。
Power-off factor is displayed as shown below. 電源オフ要因は下記のように表示されます。
Power-off by AC pulling out
mx.PDOWN
AC 抜きによる電源オフ
Power-off by anomaly detection
mx.PRT.
異常検出による電源オフ
Power-off with panel key
mx.KEY
パネルキーによる電源オフ
Power-off by remote control
mx.REM
リモコンによる電源オフ
Power-off by CI
mx.CI
CI コマンドによる電源オフ
Power-off by CEC
mx.CEC
CEC コントロールコマンドによる電源オフ
Power-off with sleep timer
mx.SLEEP
無操作スリープタイマーによる電源オフ
Power-off with no signal timer
mx.NO SIG
信号無入力で、一定期間経過したことによる電源オフ
Power-off by AirWired
mx.AW
AirWired 連動による電源オフ
Power-off by finish of iPod Charging (YSP-CU4300)
mx.CHARGE
iPod 充電終了による電源オフ （YSP-CU4300）
No history
mx.NO OFF
履歴なし
77
YSP-CU4300/YSP-CU3300/NS-WSW160
n. RS-232C DBG n. RS-232C DBG
YSP-CU4300/YSP-CU3300/
Not for service. サービスでは使用しません。
NS-WSW160
n.DBG CI n.DBG SiI
o. FACTORY PRESET o. FACTORY PRESET
This menu is used to reserve/inhibit initialization of the バックアップ IC（EEPROM：MAIN P.C.B. の IC706）の
back-up IC (EEPROM: IC706 on MAIN P.C.B.). 初期化を予約／禁止します。
INIT INHI (Initialization inhibited) / INIT INHI（初期化禁止）
o1.INHI
Initialization of the back-up IC is not executed.
Select this sub-menu to protect the values set by the user.
T
バックアップ IC の初期化は行われません。
ユーザーの設定値を保護するときは、こちらを選択してください。
F
INIT RSRV (Initialization reserved) / INIT RSRV（初期化予約）
o2.RSRV
A
Initialization of the back-up IC is reserved. (Actually, initialization is executed when the power cable is
connected to the AC outlet next.)
To reset to the original factory settings or to reset the back-up IC, select this sub-menu.
R
バックアップ IC の初期化が予約されます。（実際に初期化されるのは、次に電源コードを AC コンセン
トに接続した時です。）
D
工場出荷時やバックアップ IC をリセットしたいときは、こちらを選択してください。
78
YSP-CU4300/YSP-CU3300/NS-WSW160
p. SET INFORMATION p. SET INFORMATION
YSP-CU4300/YSP-CU3300/
This menu is used to write the model name and モ デ ル 名 と 仕 向 け 先 を バ ッ ク ア ッ プ IC（DIGITAL
NS-WSW160
destination to the back-up IC (EEPROM: IC703 on P.C.B. の IC703）に書き込みます。
DIGITAL P.C.B.). 下記の部品を交換した場合、正常動作のために本メ
When the following parts are replaced, the model ニューでモデル名と仕向け先を書き込む必要があり
name and destination MUST be written by using this ます。
menu to have proper operation.
DIGITAL P.C.B.
DIGITAL P.C.B. EEPROM：DIGITAL P.C.B. の IC703
EEPROM: IC703 on DIGITAL P.C.B.
モデル名と仕向け先を書き込むには、まず最初に
To write the model name and destination, short TP731 DIGITAL P.C.B. の TP731（IC701 の 140 ピンと接続）
(connected to pin 140 of IC701) of DIGITAL P.C.B. and と GND をショートさせます。
GND first. それから p-1. SYSTEM MODEL NAME and
Then, enter the menu item “p-1. SYSTEM MODEL DESTINATION メニューで目的のモデル名と仕向け先
NAME and DESTINATION” and write the model name を選択し、書き込みます。
and target destination by selecting them.
T
（詳細は システムモデル名と仕向け先の書き込み
(For details, refer to “WRITING SYSTEM MODEL NAME を参照してください。）
F
AND DESTINATION”)
p-1. SYSTEM MODEL NAME and DESTINATION p-1. SYSTEM MODEL NAME and DESTINATION
A
Select the target destination by pressing the リモコンの 決定 キーを繰り返し押して目的
“ENTER” key of the remote control repeatedly. の仕向け先を選択します。
R
Start writing by pressing the “RETURN” key of リモコンの 戻る キーを押して書き込みを開
the remote control. 始します。
* When writing is completed, the power will ※ 書き込みが完了すると、自動的に電源が切
D
be turned off automatically. れます。
p1.4300U
Destination / 仕向け先
U, C, T, K, A, B, G, F, L, V, S, H, J is displayed.
リモコンの 決定 キーを押す度に、仕向け表示が変わります。
J → U → C → G → E → B → T → A → F → K → L → V → R → H → S → J .....
System model name / システムモデル名
4300: YSP-CU4300
3300: YSP-CU3300
p-2. FIRMWARE VERSION p-2. FIRMWARE VERSION
The firmware version is displayed. ファームウェアバージョンが表示されます。
05.00.04
HDMI/OSD (IC101 on DIGITAL P.C.B.) / HDMI/OSD（DIGITAL P.C.B. の IC101）
DSP (IC501 on DIGITAL P.C.B.) / DSP（DIGITAL P.C.B. の IC501）
Microprocessor (IC701 on DIGITAL P.C.B.) / マイコン（DIGITAL P.C.B. の IC701）
79
YSP-CU4300/YSP-CU3300/NS-WSW160
q. MICROPROCESSOR INFORMATION q. MICROPROCESSOR INFORMATION
YSP-CU4300/YSP-CU3300/
This menu is used to display the firmware version and ファームウェアバージョン、チェックサムが表示さ
NS-WSW160
checksum values. れます。
The checksum is obtained by adding the data at チェックサムは、データを 8 ビットごとに加算して
every 8-bit and expressing the result as a 4-digit いき、4 桁の 16 進数で表記したものです。
hexadecimal notation.
※ 図中の数値は参考例です。
* Numeric values in the figure are given as reference
only.
q-1. MICROPROCESSOR VERSION
MvE0612
The firmware version of microprocessor (IC701 on DIGITAL P.C.B.) is displayed.
マイコン（DIGITAL P.C.B. の IC701）のファームウェアバージョンが表示されます。
q-2. MICROPROCESSOR CHECKSUM
Ms27C8
The checksum value of microprocessor (IC701 on DIGITAL P.C.B.) is displayed.
T
マイコン（DIGITAL P.C.B. の IC701）のチェックサムが表示されます。
F
q-3. DSP (DA81Y) VERSION
Dv00.08r
The firmware version of DSP (DA81Y, IC501 on DIGITAL P.C.B.) is displayed.
A
DSP1（TI1、MAIN P.C.B. の IC110）のファームウェアバージョンが表示されます。
q-4. DSP (DA81Y) CHECKSUM
R
Ds871D4052
The checksum value of DSP (DA81Y, IC501 on DIGITAL P.C.B.) is displayed.
DSP（DA81Y、DIGITAL P.C.B. の IC501）のチェックサムが表示されます。
D
q-5. HDMI/OSD VERSION
O:04
The firmware version of HDMI/OSD (IC101 on DIGITAL P.C.B.) is displayed.
HDMI/OSD（DIGITAL P.C.B. の IC101）のファームウェアバージョンが表示されます。
q-6. AirWired VERSION
A:----
The firmware version of AirWired is displayed.
AirWired のファームウェアバージョンが表示されます。
q-7. USB VERSION (YSP-CU4300)
U:20111228
The firmware version of USB HOST (IC302 on INPUT P.C.B.) is displayed.
USB HOST（INPUT P.C.B. の IC302）のファームウェアバージョンが表示されます。
80
YSP-CU4300/YSP-CU3300/NS-WSW160
■ DISPLAY DATA
● V901 : 011BT267GINAK (POWER P.C.B.)
YSP-CU4300/YSP-CU3300/
39 1
NS-WSW160
PATTERN AREA
● PIN CONNECTION
Pin No. 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23
Connection F2 NX NP NP LGND PGND VH VDD OSC RESET CS CP DA TSA TSB 11G Q11G
Pin No. 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Connection NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NP NP NX F1
Note: 1) F1, F2 ..... Filament pin 2) NP ..... No pin 3) DL ..... Datum line pin 4) 11G ..... Grid 5) NX ..... No extend pin
T
6) LGND ..... Logic GND pin 7) PGND ..... Power GND pin 8) VH ..... High voltage supply pin 9) VDD ..... Logic voltage supply pin
10) CP ..... Shift resister clock 11) DA ..... Serial data input 12) TSA, B ..... Test pin 13) CS ..... Chip select input pin
14) RESET ..... Reset input 15) OSC ..... Pin for self-oscillation 16) Q11G ..... Driver output port 17) Solder composition is Sn-3Ag-0.5Cu.
F
18) NC ..... No connection
A
● GRID ASSIGNMENT
11G
D R
1G 2G 3G 4G 5G 6G 7G 8G 9G 10G
1-1 2-1 3-1 4-1 5-1
1-2 2-2 3-2 4-2 5-2
1-3 2-3 3-3 4-3 5-3 S9
1-4 2-4 3-4 4-4 5-4 S8
S7
S6
S5
S4
1-5 2-5 3-5 4-5 5-5 S3
S2
S1
1-6 2-6 3-6 4-6 5-6
1-7 2-7 3-7 4-7 5-7
(1G – 10G) (11G)
81
YSP-CU4300/YSP-CU3300/NS-WSW160
• Anode connection
YSP-CU4300/YSP-CU3300/
1G – 10G 11G
NS-WSW160
D0 1-1
D1 2-1
D2 3-1
D3 4-1
D4 5-1
D5 1-2
D6 2-2
D7 3-2
D8 4-2
D9 5-2
T
D10 1-3
D11 2-3
F
D12 3-3
D13 4-3
A
D14 5-3
R
D15 1-4
D16 2-4
D
D17 3-4
D18 4-4
D19 5-4
D20 1-5
D21 2-5
D22 3-5
D23 4-5
D24 5-5
D25 1-6 –
D26 2-6 S9
D27 3-6 S8
D28 4-6 S7
D29 5-6 S6
D30 1-7 S5
D31 2-7 S4
D32 3-7 S3
D33 4-7 S2
D34 5-7 S1
82
YSP-CU4300/YSP-CU3300/NS-WSW160
■ IC DATA
YSP-CU4300 YSP-CU3300
YSP-CU4300/YSP-CU3300/
IC101: SII9573CTUC (DIGITAL P.C.B.)
NS-WSW160
HDMI port processors
* No replacement part available. / サービス部品供給なし
Always-On
CEC A0
Section
CEC A1
73 CEC Interface
CBUS/ CEC Interface
Mobile HD
Controller 0 Controller 1 72
HPD Control
78,82,86,90,94,99 CBUS0
Serial Ports CBUS1
DDC0 RnPWR5V,
DDC1 SBVCC5V
DDC Booting
DDC2 NVRAM Power
DDC3 EDID SRAM Sequencer 101
DDC4
DDC5 INT
DDC6
Configuration, Status, 69
HDCP and Interrupt-Control
I2C OTP
Local Registers Registers
I2C
DDC TX
TPI HW
E I2S/SPDIF/
DSD
Power-Down
M Main
Section Audio Output
T
R0X U 76,80,84,88,92,97
TMDS Rx Multi-Channel I2S/SPDIF
10-17
(Port 0)
A X
Audio Input
HDMI/
R1X TMDS Rx
M
U
MHL
Stream
C OSD
SPI
F
(Port 1) Receiver
X Mixer
20-27 InstaPort
M
U Main
TMDS Tx T0X
R2X TMDS Rx X
(Port 0) HDCP
(Port 2) 151-158
28-35 Encryption
SRC
HDCP
A
InstaPrevue
Decryption
R3X TMDS Rx
39-46
(Port 3)
B D
R4X Video/
TMDS Rx M HDMI/ Sub
R
Audio
(Port 4) U MHL M TMDS Tx T1X
47-54 Splitter
X Receiver U (Port 1)
InstaPort
R5X
TMDS Rx
X
M G HDCP Encryption 141-148
57-64 U
(Port 5)
X
F
D
D[19..0] Parallel M
Audio Output ENB I2S/SPDIF
Video U Sub
1-6,161-171,174-176 2 Channel
Input X
Audio Input
Video
Pattern
Generator
ARC0/1 Rx
136,137 ARC
Input
ARC0/1 Tx
and
Output
37 CVCC12
38 AVDD33
36 AVDD12
19 AVDD33
18 AVDD12
9 HSYNC
8 VSYNC
40 R3XC+
29 R2XC+
21 R1XC+
11 R0XC+
44 R3X1+
42 R3X0+
35 R2X2+
33 R2X1+
31 R2X0+
27 R1X2+
25 R1X1+
23 R1X0+
17 R0X2+
15 R0X1+
13 R0X0+
39 R3XC-
28 R2XC-
20 R1XC-
10 R0XC-
43 R3X1-
41 R3X0-
34 R2X2-
32 R2X1-
30 R2X0-
26 R1X2-
24 R1X1-
22 R1X0-
16 R0X2-
12 R0X0-
14 T0X1-
6 D19
5 D18
4 D17
3 D16
2 D15
1 D14
7 DE
R3X2- 45 176 D13
R3X2+ 46 175 D12
R4XC- 47 174 D11
R4XC+ 48 173 IOVCC33
R4X0- 49 172 IDCK
R4X0+ 50 171 D10
R4X1- 51 170 D9
R4X1+ 52 169 D8
R4X2- 53 168 D7
R4X2+ 54 167 D6
AVDD12 55 166 D5
AVDD33 56 165 D4
R5XC- 57 164 D3
R5XC+ 58 163 D2
R5X0- 59 162 D1
R5X0+ 60 161 D0
R5X1- 61 160 CVCC12
R5X1+ 62 159 TOX2+
G
R5X2- 63 DGND 158 TOX2-
R5X2+ 64 157 TOX1+
CVCC12 65 156 TOX1-
CSCL 66 155 TOX0+
CSDA 67 154 TOX0-
INT 68 153 TOXC+
RESET# 69 152 TOXC-
TPWR_CI2CA 70 151 TDVDD12
CEC_A1 71 150 TPVDD12
CEC_A0/WAKEUP 72 149 T1X2+
DSDA6(VGA) 73 148 T1X2-
DSCL6(VGA) 74 147 T1X1+
RSVDL 75 146 T1X1-
DSDA0 76 145 T1X0+
DSCL0 77 144 T1X0-
CBUS_HPD0 78 143 T1XC+
R0PWR5V 79 142 T1XC-
DSDA1 80 141 TDVDD12
DSCL1 81 140 TPVDD12
CBUS_HPD1 82 139 CVCC12
R1PWR5V 83 138 ARC1
DSDA2 84 137 ARC0
DSCL2 85 136 SD1_IN/SD1_OUT/SPDIF1_IN/SPDIF1_OUT
CBUS_HPD2 86 135 WS1_IN/WS1_OUT
R2PWR5V 87 134 SCK1_IN/SCK1_OUT
133
DSDA3 88 SD0_IN/SPDIFO_IN
R5PWR5V 100
SBVCC5V 101
VCC33OUT 102
MHL_CD0/GPIO0 103
MHL_CD1/GPIO1 104
TX_HPD0 105
TXDSDA0 106
TXDSCL0 107
TX_HPD1 108
TXDSDA1 109
TXDSCL1 110
APLL12 111
XTALVCC33 112
XTALOUT 113
XTALIN 114
XTALGND 115
CVCC12 116
SS/GPIO2 117
SCLK/GPIO3 118
SD0/GPIO4 119
SDI/GPIO5 120
WS0_OUT/DR0 121
SCK0/DDCK 122
IOVCC33 123
SD0_0/DL0 124
MCLK 125
SD0_1/DR1/GPIO6 126
SD0_2/DL1/GPIO7 127
SD0_3/DR2/GPIO8 128
MUTEOUT/GPIO9 129
SPDIF0_OUT/DL2 130
WS0_IN/GPIO11 131
132
DSCL3 89
CBUS_HPD3 90
R3PWR5V 91
DSDA4 92
DSCL4 93
CBUS_HPD4 94
R4PWR5V 95
RSVDL 96
DSDA5 97
DSCL5 98
CBUS_HPD5 99
SCK0_IN/GPIO10
83
YSP-CU4300/YSP-CU3300/NS-WSW160
HDMI Receiver and MHL Port Pins HDMI Transmitter Port Pins
YSP-CU4300/YSP-CU3300/
Pin Function Pin Function
Type I/O Detail of Function Type I/O Detail of Function
No. Name No. Name
NS-WSW160
12 R0X0- 154 T0X0-
13 R0X0+ 155 T0X0+ HDMI transmitter Port 0 TMDS output
14 R0X1- HDMI receiver Port 0 TMDS input data 156 T0X1- data pairs.
TMDS Input TMDS Output
15 R0X1+ pairs. 157 T0X1+ Main HDMI transmitter output Port
16 R0X2- 158 T0X2- TMDS data pairs.
17 R0X2+ 159 T0X2+
10 R0XC- HDMI receiver Port 0 TMDS input clock HDMI transmitter Port 0 TMDS output
TMDS Input 152 T0XC-
11 R0XC+ pair. clock pair.
TMDS Output
22 R1X0- Main HDMI transmitter output Port
153 T0XC+
23 R1X0+ TMDS clock pair.
24 R1X1- HDMI receiver Port 1TMDS input data 144 T1X0-
TMDS Input
25 R1X1+ pairs. 145 T1X0+ HDMI transmitter Port 1 TMDS output
26 R1X2- 146 T1X1- data pairs.
TMDS Output
27 R1X2+ 147 T1X1+ Sub HDMI transmitter output Port
20 R1XC- HDMI receiver Port 1 TMDS input clock 148 T1X2- TMDS data pairs.
TMDS Input
T
21 R1XC+ pair. 149 T1X2+
30 R2X0- HDMI transmitter Port 1 TMDS output
142 T1XC-
clock pair.
F
31 R2X0+
TMDS Output
32 R2X1- HDMI receiver Port 2 TMDS input data Sub HDMI transmitter output Port
TMDS Input 143 T1XC+
33 R2X1+ pairs. TMDS clock pair.
A
34 R2X2-
35 R2X2+
28 R2XC- HDMI receiver Port 2 TMDS input clock
R
TMDS Input
29 R2XC+ pair.
41 R3X0-
42 R3X0+ Audio Return Channel Pins
D
43 R3X1- HDMI receiver Port 3 TMDS input data Pin Function
TMDS Input Type I/O Detail of Function
44 R3X1+ pairs. No. Name
45 R3X2- 137 ARC0 Audio Return Channels 0 and 1.
46 R3X2+ These pins are used to transmit or
39 R3XC- receive an IEC60958-1 audio stream.
HDMI receiver Port 3 TMDS input clock
TMDS Input In ARC transmitter mode, received
40 R3XC+ pair.
on the SPDIFn_IN input pin, this pin
49 R4X0- transmits an S/PDIF signal to an ARC
50 R4X0+ receiver-capable source (such as HTiB)
or a repeater (such as AVR) devices,
51 R4X1- HDMI receiver Port 4 TMDS input data
TMDS Input Input/ using single-mode ARC.
52 R4X1+ pairs. Analog
138 ARC1 Output In ARC receiver mode, transmitted
53 R4X2- through the SPDIFn_OUT pin, this pin
54 R4X2+ receives an S/PDIF signal from an ARC
47 R4XC- transmitter-capable sink (such as DTV)
HDMI receiver Port 4 TMDS input clock
TMDS Input device, using single-mode ARC. In
48 R4XC+ pair.
combination with external components,
59 R5X0- common-mode ARC can be received.
60 R5X0+ Each channel can either be an ARC
61 R5X1- input or an ARC output at one time.
HDMI receiver Port 5 TMDS input data
TMDS Input
62 R5X1+ pairs.
63 R5X2-
64 R5X2+
57 R5XC- HDMI receiver Port 5 TMDS input clock
TMDS Input
58 R5XC+ pair.
Note: For Port 0 and Port 5 that have been configured as MHL inputs, the
R0X0+ and R0X0- pin pair and R5X0+ and R5X0- pin pair carry the
respective MHL signals.
84
YSP-CU4300/YSP-CU3300/NS-WSW160
Audio Pins SPI Interface Pins
YSP-CU4300/YSP-CU3300/
Pin Function Pin Function
Type I/O Detail of Function Type I/O Detail of Function
No. Name No. Name
NS-WSW160
WS0_OUT/ Main port I2S word select output/DSD Input/
121 LVTTL Output 117 SS/GPIO2 LVTTL SPI slave select/programmable GPIO 2.
DR0 data right bit 0. Output
SCK0/ Main port I2S serial clock output/DSD LVTTL
122 LVTTL Output
DDCK clock output. SCLK/ Schmitt Input/
118 SPI clock/programmable GPIO 3.
Main port I2S serial data 0 output/DSD GPIO3 Open Output
124 SDO_0/DL0 LVTTL Output drain/
data left bit 0 output.
125 MCLK LVTTL Output Master clock output. LVTTL
Schmitt Input/ SPI slave data output/master data
119 SDO/GPIO4
Open Output input/programmable GPIO 4.
Main port I2S serial data 1 output/DSD
SDO_1/ drain
126 LVTTL Output data right bit 1 output/programmable
DR1/GPIO6
GPIO 6.
LVTTL
Main port I2S serial data 2 output/DSD Schmitt Input/ SPI slave data input/master data
SDO_2/DL1/ 120 SDI/GPIO5
127 LVTTL Output data left bit 1 output/programmable Open Output output/programmable GPIO 5.
GPIO7 drain
GPIO 7.
SDO_3/ Main port I2S serial data 3 output/DSD
128 LVTTL Output
T
DR2/GPIO8 data right bit 2/programmable GPIO 8.
MUTEOUT/ Input/ Mute audio output/programmable GPIO
129 LVTTL
GPIO9 Output 9.
F
SPDIF0_ Analog/ Main port S/PDIF output/DSD data left
130 Output Parallel Video Bus
OUT/DL2 LVTTL bit 2.
A
WS0_IN/ Input/ Main port I2S word select input/ Pin Function
131 LVTTL Type I/O Detail of Function
GPIO11 Output programmable GPIO 11. No. Name
SCK0_IN/ Input/ Main port I2S serial clock input/ 1 D14
R
132 LVTTL
GPIO10 Output programmable GPIO 10. 2 D15
SD0_IN/ Analog/ Main port I2S serial data input/S/PDIF 3 D16
133 Input
SPDIF0_IN LVTTL input. 4 D17
D
SCK1_IN/ Input/ Sub port I2S serial clock1 input/I2S 5 D18
134 LVTTL
SCK1_OUT Output serial bit clock output. 6 D19
WS1_IN/ Input/ Sub port I2S word select input/I2S 161 D0
135 LVTTL
WS1_OUT Output word select output. 162 D1 Video data inputs.
163 D2
SD1_IN/
SD1_OUT/ Sub port I2S serial data input/I2S serial 164 D3
LVTTL Input The video data inputs can be configured
Input/
136 SPDIF1_IN/ LVTTL data1 output/ SPDIF input//SPDIF 165 D4 to support a wide variety of input formats,
Output
SPDIF1_ output. 166 D5 including multiple RGB and YCbCr bus
OUT formats, using register settings.
167 D6
168 D7
169 D8
170 D9
171 D10
174 D11
Crystal Pins 175 D12
Pin Function 176 D13
Type I/O Detail of Function
No. Name 7 DE LVTTL Input Data enable input.
LVTTL 9 HSYNC LVTTL Input Horizontal sync input.
113 XTALOUT 5V Output Crystal clock output. 8 VSYNC LVTTL Input Vertical sync input.
tolerant 172 IDCK LVTTL Input Input data clock.
LVTTL
114 XTALIN 5V Input Crystal clock input.
tolerant
85
YSP-CU4300/YSP-CU3300/NS-WSW160
System Switching Pins
YSP-CU4300/YSP-CU3300/
Pin
Function Name Type I/O Detail of Function
No.
NS-WSW160
76 DSDA0
80 DSDA1 DDC I2C data for respective HDMI receiver port.
84 DSDA2 LVTTL Schmitt Open
Input/Output
88 DSDA3 drain 5 V tolerant These signals are true open drain, and do not pull to ground when power is not
92 DSDA4 applied to the device. These pins require an external pull-up resistor.
97 DSDA5
DDC I2C data for VGA port.
LVTTL Schmitt Open
73 DSDA6(VGA) Input/Output
drain 5 V tolerant This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
77 DSCL0
81 DSCL1 DDC I2C clock for respective HDMI receiver port.
85 DSCL2 LVTTL Schmitt Open
Input
89 DSCL3 drain 5 V tolerant These signals are true open drain, and do not pull to ground when power is not
93 DSCL4 applied to the device. These pins require an external pull-up resistor.
T
98 DSCL5
DDC I2C clock for VGA port.
F
LVTTL Schmitt Open
74 DSCL6(VGA) Input
drain 5 V tolerant This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
A
DDC master I2C data for HDMI transmitter Port 0.
LVTTL Schmitt Open
106 TXDSDA0 Input/Output
drain 5 V tolerant This signal is true open drain, and does not pull to ground when power is not
R
applied to the device. This pin requires an external pull-up resistor.
DDC master I2C data for HDMI transmitter Port 1.
LVTTL Schmitt Open
D
109 TXDSDA1 Input/Output
drain 5 V tolerant This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
DDC master I2C clock for HDMI transmitter Port 0.
LVTTL Schmitt Open
107 TXDSCL0 Input/Output
drain 5 V tolerant This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
DDC master I2C clock for HDMI transmitter Port 1.
LVTTL Schmitt Open
110 TXDSCL1 Input/Output
drain 5 V tolerant This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
79 R0PWR5V
83 R1PWR5V 5 V port detection input for respective HDMI receiver port.
87 R2PWR5V Connect to 5 V signal from HDMI input connector. These pins require a 10 ohms
Power Input
91 R3PWR5V series resistor, a 5.1 k-ohms pull down resistor, and at least a 1 μF capacitor to
95 R4PWR5V ground.
100 R5PWR5V
78 CBUS_HPD0
82 CBUS_HPD1
86 CBUS_HPD2 LVTTL 1.5 mA 5 V Hot plug detect output for the respective HDMI receiver port.
Input/Output
90 CBUS_HPD3 tolerant Analog In MHL mode, these pins serve as the respective CTRL bus.
94 CBUS_HPD4
99 CBUS_HPD5
105 TX_HPD0 LVTTL 5 V tolerant Input Hot plug detect input for HDMI transmitter Port 0.
108 TX_HPD1 LVTTL 5 V tolerant Input Hot plug detect input for HDMI transmitter Port 1.
103 MHL_CD0/GPIO0 LVTTL Input/Output MHL cable detect 0/programmable GPIO 0.
104 MHL_CD1/GPIO1 LVTTL Input/Output MHL cable detect 1/programmable GPIO 1.
86
YSP-CU4300/YSP-CU3300/NS-WSW160
Control Pins
YSP-CU4300/YSP-CU3300/
Pin
Function Name Type I/O Detail of Function
No.
NS-WSW160
Local configuration/status I2C clock.
Schmitt Open drain 5
66 CSCL Input
V tolerant Chip configuration/status is accessed via this I2C port. This pin is true open
drain, so it does not pull to ground if power is not applied.
Local configuration/status I2C data.
LVTTL Schmitt Open
67 CSDA Input/Output
drain 5 V tolerant Chip configuration/status is accessed via this I2C port. This pin is true open
drain, so it does not pull to ground if power is not applied.
External reset.
Active LOW. Must be pulled up to VCC33OUT. When main power is not provided
69 RESET# Schmitt Input to the system, the microprocessor must present a high impedance of at least
100 k-ohms to RESET#. If this condition is not met, a circuit to block the leakage
from VCC33OUT to the microprocessor GPIO may be required.
Configuration Pins
T
Pin
Function Name Type I/O Detail of Function
No.
F
I2C slave address input / Transmit power sense output.
During power-on-reset (POR), this pin is used as an input to latch the I2C
A
subaddress. The level on this pin is latched when the POR transitions from the
70 TPWR_CI2CA LVTTL Input/Output asserted state to the de-asserted state.
After completion of POR, this pin is used as the TPWR output. A register setting
R
can change this pin to show if the active port is receiving a TMDS clock.
Schmitt Open drain Interrupt output.
68 INT Output
8 mA 3.3 V tolerant This is an open-drain output and requires an external pull-up resistor.
D
CEC Pins
Pin
Function Name Type I/O Detail of Function
No.
Primary CEC I/O used for interfacing to CEC devices This signal is electrically
compliant with the CEC specification.
As an input, this pin acts as an LVTTL schmitt triggered input and is 5 V tolerant.
As an output, the pin acts as an NMOS driver with resistive pull-up.
This pin has an internal pull-up resistor.
CEC Compliant 5V This signal should be connected to the CEC signal of all HDMI input and output
72 CEC_A0 tolerant, Schmitt Input/Output ports if the system supports just one CEC line.
triggered, LVTTL OR
In a system designed to have separate CEC connectivity for the HDMI input and
output ports, this signal should be connected to the CEC signal of all the input
ports supported in the system.
This signal and CEC_A0 each connect to a separate CEC controller within the
port processor and are independent of each other.
Secondary CEC I/O used for interfacing to CEC devices.
This signal is electrically compliant with the CEC specification. As an input, this
pin acts as an LVTTL schmitt triggered input and is 5 V tolerant. As an output,
the pin acts as an NMOS driver with resistive pull-up. This pin has an internal
pull-up resistor.
CEC Compliant 5V
This is an optional CEC signal provided for system designers who want to
71 CEC_A1 tolerant, Schmitt Input/Output
implement a system with two independent CEC lines, such as a system that
triggered, LVTTL
supports a separate CEC line for the HDMI input ports and the HDMI output
ports. In the example of a DTV that provides a second HDMI output using the
SiI957n port processor; this signal can be connected to the CEC signal of the
output port while the CEC_A1 signal is connected to the CEC signal of the input
ports.
This signal and CEC_A1 each connect to a separate CEC controller within the
port processor and are independent of each other.
87
YSP-CU4300/YSP-CU3300/NS-WSW160
Power and Ground Pins
YSP-CU4300/YSP-CU3300/
Pin
Function Name Type I/O Detail of Function
No.
NS-WSW160
19
38 AVDD33 Power 3.3 V TMDS core VDD.
56
123
IOVCC33 Power 3.3 V I/O VCC.
173
Local power from system.
101 SBVCC5 Power 5.0 V
This pin requires a 10 ohms series resistor.
18
36 AVDD13 Power 1.3 V TMDS receiver core VDD.
55
37
65
116 CVCC13 Power 1.3 V Digital core VCC.
139
160
T
111 APLL13 Power 1.3 V PLL analog VCC.
102 VCC33OUT Power 3.3 V Internal regulator 3.3 V output.
F
140
TPVDD13 Power 1.3 V Analog power for TMDS Tx core.
150
141
TDVDD13 Power 1.3 V Digital power for TMDS Tx core.
A
151
112 XTALVCC33 Power 3.3 V PLL crystal oscillator power.
115 XTALGND Ground GND PLL crystal oscillator ground.
R
The ePad must be soldered to ground, as this is the only ground connection for
ePad GND Ground GND
the device.
D
Reserved Pin
Pin
Function Name Type Detail of Function
No.
75
RSVDL Reserved Reserved, must be tied to ground.
96
88
YSP-CU4300/YSP-CU3300/NS-WSW160
IC302: BU94607ARKV-E (DIGITAL P.C.B.)
YSP-CU4300/YSP-CU3300/
USB host WAV/AAC/WMA/MP3 decoder LSI
NS-WSW160
TESTI2/MCLK
TEST_PLL2
TEST_PLL1
XOUT_PLL
VDD_PLL
VSS_PLL
VCDACO
USB_DM
XIN_PLL
USB_DP
VOREFI
RDACO
AMUTE
DAVDD
LDACO
TESTI1
DAVSS
AVSSC
REXTI
DVSS
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
LED_ERROR/SS_CS 61 40 AVDDC
LED_PLAY/SS_DI 62 Audio DAC PLL USB
39 ATEST1
PHY
LED_PSD/SS_CLK 63 38 DVDD_M2
LED_PUSB/SS_DO 64 37 DVSS
LED_ACCESS/LRCKO 65
Audio
Sound Effecter USB 36 TEST10
Controller
LED_RANDOM/BCKO 66 Controller
35 TEST9
LED_REPEAT/SDATAO 67
34 TEST8
DVDDIO 68 AAC / WMA / MP3
33 DVDDIO
Decoder
TEST13 69
IPL 32 TEST7
TEST14 70 FAT 31 TEST6
SIO I/F
SEL_USB 71 File system
Controller 30 TEST5
T
TEST4 72
29 TEST/CKL12MO
TEST3 73
SD I/F 28 FL_CS
F
TEST2 74 Controller 27 DVSS
TEST1 75
26 SD_CS
TMODE 76
25 SD_DI
System I2C I/F
A
DVSS 77
CD-ROM I/F
LDO Controller Controller 24 SD_CLK
DVDD_M1 78
23 SD_DO
DVDDIO 79
R
22 SD_CON
TEST0 80
21 SD_PW
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
D
RESETX
TEST15
TEST16
SEL_SLAVE
SEL_MP3/INREQI
SEL_DOUT/LRCKI
SEL_VOL/BCKI
SEL_APLAY/SDATAI
SEL_UTPKT/BFULLO
DVSS
IRPTO
SEARCH
DVDDIO
KEY_ROW1/MCHNG
KEY_ROW2/BUSY
KEY_ROW3/SCL
KEY_ROW4/SDA
KEY_COL1/A0
KEY_COL2/A1
KEY_COL3/TEST
Pin Function
Port Name I/O Detail of Function
No. Name
1 RESETX RESETX I System reset terminal
2 TEST15 SCLM O [TEST15] pull-up at 2.2k-ohms to VDD1 system power supply terminal (TEST pin)
3 TEST16 SDAM O [TEST16] pull-up at 2.2k-ohms to VDD1 system power supply terminal (TEST pin)
4 SEL_SLAVE SEL_SLAVE I Slave mode selection (H: Stand alone mode, L: Slave mode)
5 SEL_MP3/INREQI INREQI I [SEL_MP3] MPEG audio layer selection
(H: Only MP3, L: MP1, MP2 and MP3 can be playback), [INREQI] input data valid
6 SEL_DOUT/LRCKI LRCKI I [SEL_DOUT] digital audio out selection (H: Disable, L: Enable)
[LRCKI] digital audio channel clock input terminal
7 SEL_VOL/BCKI BCKI I [SEL_VOL] volume operation selection (H: Volume+- effective, L: Volume+- inavaildity),
[BCKI] digital audio bit clock input terminal
8 SEL_APLAY/SDATAI SDATAI I [SEL_APLAY] at device (USB, DS) connection, auto play mode selection
(H: It stop, L: It playback), [SDATAI] digital audio data input terminal
9 SEL_UTPKT/BFULLO BFULLO I/O [SEL_UTPKT] USB test packet output selection (H: Normal, L: Test packet),
[BFULLO] input buffer FULL flag output terminal
10 DVSS DVSS – GND terminal
11 IRPTO IRPTO O To HOST interruption output terminal
12 SEARCH SEARCH O Search flag terminal
13 DVDDIO DVDDIO – IO power supply (VDD1) terminal
14 KEY_ROW1/MCHNG MCHNG I/O [KEY_ROW1] KEY matrix terminal, [MCHNG] music change flag terminal
15 KEY_ROW2/BUSY BUSY I/O [KEY_ROW2] KEY matrix terminal, [BUSY] busy flag terminal
16 KEY_ROW3/SCL SCL I [KEY_ROW3] KEY matrix terminal, [SCL] I2C slave clock I/F input terminal
17 KEY_ROW4/SDA SDA I/O [KEY_ROW4] KEY matrix terminal, [SDA] I2C slave data I/F terminal
18 KEY_COL1/A0 A0 O/I [KEY_COL1] KEY matrix terminal, [A0] I2C slave address selection
19 KEY_COL2/A1 A1 O/I [KEY_COL2] KEY matrix terminal, [A1] I2C slave address selection
20 KEY_COL3/SEL_I2C TEST O/I [KEY_COL3] KEY matrix terminal,
[SEL_I2C] pull-up to VDD1 system power supply terminal
21 SD_WP SD_WP I SD card Write Protect terminal
22 SD_CON SD_CON I SD card Connect terminal
89
YSP-CU4300/YSP-CU3300/NS-WSW160
Pin Function
Port Name I/O Detail of Function
YSP-CU4300/YSP-CU3300/
No. Name
23 SD_DO SD_DO I SD card Data In terminal
NS-WSW160
24 SD_CLK SD_CLK O SD card Clock terminal
25 SD_DI SD_DI O SD card Data Out terminal
26 SD_CS SD_CS O SD card Chip Select terminal
27 DVSS VDSS – GND terminal
28 FL_CS FL_CS O Serial FLASH ROM chip select terminal
29 TEST/CLK12MO TEST I/O [TEST] pull-up to VDD1 system power supply terminal (TEST pin),
[CLK12MO] 12MHz clock output terminal
30 TEST5 TEST5 O [TEST5] OPEN (TEST pin)
31 TEST6 TEST6 I [TEST6] pull-up to VDD1 system power supply terminal (TEST pin)
32 TEST7 TEST7 I [TEST7] pull-up to VDD1 system power supply terminal (TEST pin)
33 DVDDIO DVDDIO – IO power supply (VDD1) terminal
34 TEST8 TEST8 I [TEST8] pull-up to VDD1 system power supply terminal (TEST pin)
35 TEST9 TEST9 I [TEST9] pull-up to VDD1 system power supply terminal (TEST pin)
36 TEST10 TEST10 O OPEN (TEST pin, IPL ERROR flag output)
37 DVSS DVSS – GND terminal
38 DVDD_M2 DVDD – CORE power supply (VDD2) monitor terminal, connect to DVDD_M1 pin
39 ATEST1 ATEST1 O USB TEST terminal (TEST pin), OPEN
T
40 AVDDC ADVDD – USB power supply (VDD1) terminal
41 USB_DM USB_DM I/O USB D-I/O terminal
F
42 USB_DP USB_DP I/O USB D+I/O terminal
43 AVSSC AVSSC – USB GND terminal
44 REXTI REXTI O USB bias resistor (12k-ohms) connecting terminal
A
45 VOREFI VOREFI O USB TEST terminal (TEST pin), OPEN
46 VSS_PLL VSS_PLL – PLL GND terminal
47 TEST_PLL1 TEST_PLL1 I PLL TEST terminal (TEST pin), OPEN
R
48 XIN_PLL XIN_PLL I X'tal (16.9344MHz) connecting input terminal
49 XOUT_PLL XOUT_PLL O X'tal (16.9344MHz) connecting output terminal
50 TEST_PLL2 TEST_PLL2 O PLL TEST terminal (TEST pin), pull-up to VDD1 system power supply terminal
D
51 VDD_PLL VDD_PLL – PLL power supply (VDD1) terminal
52 DAVSS DA_VSS – Audio DAC GND terminal
53 RDACO RDACO O Audio DAC Rch line output terminal
54 VCDACO VCDACO O Audio DAC reference voltage output terminal
55 LDACO LDACO O Audio DAC Lch line output terminal
56 DAVDD DAVDD – Audio DAC power supply (VDD1) terminal
57 DVSS DVSS – GND terminal
58 AMUTE AMUTE O Audio Mute output terminal (H: MUTE OFF, L: MUTE ON)
59 TEST11 TEST11 O OPEN (TEST pin)
60 TEST12/MCLK TEST12 O [TEST12] OPEN (TEST pin),
[MCLK] digital audio master clock (16.9344MHz) output terminal
61 LED_ERROR/SS_CS SS_CS O/I [LED] lighting output terminal at ERROR, [SS_CS] slave SIO chip select in terminal
62 LED_PLAY/SS_DI SS_DI O/I [LED] lighting output terminal at PLAY, [SS_DI] slave SIO data in terminal
63 LED_PSD/SS_CLK SS_CLK O/I [LED] lighting output terminal at PLAY for SD card, [SS_CLK] slave SIO clock in terminal
64 LED_PUSB/SS_DO SS_DO O [LED] lighting output terminal at PLAY for USB memory,
[SS_DO] slave SIO data out terminal
65 LED_ACCESS/LRCKO LRCKO O [LED] lighting output terminal when memory is being accessed,
[LRCKO] digital audio channel clock or SPDIF output terminal
66 LED_RANDOM/BCKO BCKO O [LED] lighting output terminal at PLAY for RANDOM,
[BCKO] digital audio bit clock output terminal
67 LED_REPEAT/SDATAO SDATAO O [LED] lighting output terminal at PLAY for REPEAT,
[SDATAO] digital audio data output terminal
68 DVDDIO DVDDIO – IO power supply (VDD1) terminal
69 TEST13 TEST13 O OPEN (TEST pin)
70 TEST14 TEST14 O OPEN (TEST pin)
71 SEL_USB SEL_USB I At device (USB, SD) connection, 1st device detection selection (H: USB, L: SD)
72 TEST4 TEST4 I Pull-up to VDD1 system power supply terminal (TEST pin)
73 TEST3 TEST3 I Pull-up to VDD1 system power supply terminal (TEST pin, L: IPL write mode 1)
74 TEST2 TEST2 I Pull-up to VDD1 system power supply terminal (TEST pin, L: IPL write mode 2)
75 TEST1 TEST1 I Pull-up to VDD1 system power supply terminal (TEST pin)
76 TMODE TMODE I Connect to GND (TEST pin)
77 DVSS DVSS – GND terminal
78 DVDD_M1 DVDD – CORE power supply (VDD2) monitor terminal, connect to bypass condenser
79 DVDDIO DVDDIO – IO power supply (VDD1) terminal
80 TEST0 TEST0 I Connect to GND (TEST pin)
90
YSP-CU4300/YSP-CU3300/NS-WSW160
IC501: D81YK113CZKB400 (DIGITAL P.C.B.)
YSP-CU4300/YSP-CU3300/
DSP (Digital signal processor)
NS-WSW160
JTAG Interface DSP Subsystem
System Control C674x™
DSP
Input PLL/Clock MICROPROCESSOR
Clock(s) Generator
w/OSC Memory Protection
I/O Protection AET
General-
Purpose 32 KB 32 KB
Timer L1 Pgm L1 RAM
Power/Sleep
General- Controller
256 KB L2 RAM
Purpose
Timer RTC/ Pin
(Watchdog) 32-KHz Multiplexing 1024 KB L2 ROM
OSC
Switched Central Resource (SCR)
Peripherals
DMA Audio Ports Serial Interfaces
GPIO
T
EDMA3 dMAX McASP I2C SPI UART
w/FIFO
DMA Shared Memory
F
128 KB
eHRPWM eCAP eQEP RAM
Connectivity External Memory Interfaces
A
USB2.0 EMIFA(8b/16b) EMIFB
OTG Ctlr HPI MMC/SD NAND/Flash SDRAM Only
PHY (8b) 16b SDRAM (16b/32b)
R
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SPI0_CLK/ SPI1_CLK/ EMA_D[0]/
EMA_CS[3]/ EMA_CS[0]/ EMA_D[9]/
AXR1[0]/ AXR1[11]/ EQEP1I/ EQEP1S/ EMA_A[0]/ EMA_A[4]/ EMA_A[8]/ EMA_SDCKE/ MMCSD_DAT[0]/
T VSS VSS AMUTE2/ UHPI_HAS/ UHPI_HD[0]/ UHPI_HD[9]/ VSS VSS T
D
GP4[0] GP5[11] GP5[2]/ GP5[7]/ GP1[0] GP1[4] GP1[8] GP2[0] GP0[0]/
GP2[6] GP2[4] GP0[9]
BOOT[2] BOOT[7] BOOT[12]
UART0_RXD/ SPI0_ENA/ SPIO_SOMI[0]/ EMA_OE/ EMA_A[1]/ EMA_CLK/
SPI1_ENA/ EMA_D[2]/ EMA_D[1]/
I2C0_SDA/ UART0_CTS/ EMA_D[10]/
AXR1[1]/ EQEPOI/ UHPI_HDS1/ EMA_BA[0]/ MMCSD_CLK/ EMA_A[5]/ EMA_A[9]/ OBSCLK/ MMCSD_DAT[2]/ MMCSD_DAT[1]/
R DVDD TM64P0_IN12/ UART2_RXD/ EQEP0A/ UHPI_HD[10]/ DVDD R
GP4[1] GP5[8]/ GP5[3]/
GP5[0]/ AXR0[13]/ GP1[14] UHPI_HCNTL0/ GP1[5] GP1[9] AHCLKR2/ UHPI_HD[2]/
GP0[10]
UHPI_HD[1]/
GP5[12] BOOT[0] GP1[1] GP0[2] GP0[1]
BOOT[8] BOOT[3] GP2[7] GP1[15]
UART0_TXD/ EMA_CS[2]/ EMA_WE_
AXR1[3]/ I2C0_SCL/ SPI1_SCS[0]/ SPI1_SOMI[0]/ SPI0_SIMO[0]/ EMA_BA[1]/ EMA_A[2]/
DQM[1]/
EMA_D[4]/
EMA_D[12]/ EMA_D[3]/ EMA_D[11]/
AXR1[2]/ I2C1_SCL/ EQEP0S/ UHPI_HCS/ MMCSD_CMD/ EMA_A[6]/ EMA_A[11]/ MMCSD_DAT[4]/ MMCSD_DAT[3]/
P EQEP1A/ TM64P0_OUT12/ UART2_TXD/ UHPI_HHWIL/ UHPI_HCNTL1/ UHPI_HDS2/ UHPI_HD[12]/ UHPI_HD[11]/ P
GP4[2] GP5[9]/
GP5[5]/ GP5[1]/ GP2[5]/ GP1[6] GP1[11] AXR0[14]/
UHPI_HD[4]/
GP0[12]
UHPI_HD[3]/
GP4[3] GP5[13] BOOT[5] BOOT[1] GP1[13] GP1[2] GP0[4] GP0[3] GP0[11]
BOOT[9] BOOT[15] GP2[8]
SPI0_SCS[0]/ SPI1_SIMO[0]/ EMA_WAIT[0]/ EMA_RAS/
AXR1[5]/ AXR1[4]/ EMA_D[8]/ EMA_D[6]/ EMA_D[5]/
UART0_RTS/ EMA_D[14]/ EMA_D[13]/
AXR1[10]/ I2C1_SDA/ EMA_A[10]/ EMA_A[3]/ EMA_A[7]/ EMA_A[12]/ MMCSD_DAT[6]/ MMCSD_DAT[5]/
N EPWM2B/ EQEP1B/ EQEP0B/ UHPI_HRDY/ EMA_CS[5]/ UHPI_HD[8]/ UHPI_HD[14]/ UHPI_HD[13]/ N
GP5[10] GP5[4]/
GP5[6]/ GP1[10] GP1[3] GP1[7] GP1[12] UHPI_HD[6]/
GP0[14]
UHPI_HD[5]/
GP0[13]
GP4[5] GP4[4] BOOT[6] GP2[10] GP2[2] GP0[8] GP0[6] GP0[5]
BOOT[4]
EMA_WE/ EMA_WE_ EMA_D[7]/
AXR1[8]/ AXR1[7]/ AXR1[6]/ UHPI_HRW/ DQM[0]/ MMCSD_DAT[7]/ EMA_D[15]/
AXR1[9]/
M EPWM1A/ EPWM1B/ EPWM2A/ DVDD VSS VSS DVDD DVDD VSS VSS DVDD AXR0[12]/ UHPI_HINT/ UHPI_HD[7]/ UHPI_HD[15]/ M
GP4[9] GP2[3]/ AXR0[15]/ GP0[7]/ GP0[15]
GP4[8] GP4[7] GP4[6]
BOOT[14]] GP2[9] BOOT[13]
ACLKR1/ EMA_CAS/
AHCLKR1/ ECAP2/ AFSR1/ AMUTE0/
L DVDD CVDD VSS VSS VSS VSS DVDD DVDD EMB_CAS EMB_D[22] EMB_D[23] EMA_CS[4]/ L
GP4[11] APWM2/ GP4[13] RESETOUT
GP4[12] GP2[1]
AHCLKX1/ ACLKX1/ AFSX1/ EMB_WE_
EPWMSYNCI/
K GP7[14] EPWM0B/ EPWM0A/ EPWMSYNCO/
DVDD CVDD CVDD VSS VSS CVDD CVDD DVDD EMB_D[20] DQM[0]/ EMB_WE EMB_D[21] K
GP3[14] GP3[15] GP4[10] GP5[15]
EMU[0]/ EMB_D[5]/ EMB_D[6]/ EMB_D[7]/
J TMS TDI TDO TRST CVDD CVDD VSS VSS CVDD CVDD CVDD EMB_D[19] J
GP7[15] GP6[5] GP6[6] GP6[7]
USB0_ EMB_D[3]/ EMB_D[4]/
H RTC_XI RTC_XO TCK NC CVDD CVDD VSS VSS CVDD CVDD CVDD EMB_D[17] EMB_D[18] H
VDDA33 GP6[3] GP6[4]
EMB_D[1]/ EMB_D[2]/
G RTC_CVDD RTC_VSS RESET USB0_DM DVDD CVDD CVDD VSS VSS CVDD CVDD DVDD EMB_D[31] EMB_D[16] G
GP6[1] GP6[2]
EMB_D[15]/ EMB_D[0]/
F OSCOUT OSCIN NC USB0_DP DVDD CVDD RSV1 VSS VSS VSS DVDD DVDD EMB_D[29] EMB_D[30] F
GP6[15] GP6[0]
USB0_
USB0_ EMB_D[13]/ EMB_D[14]/
E PLL0_VSSA OSCVSS DRVVBUS/ DVDD VSS VSS DVDD DVDD VSS VSS DVDD EMB_D[27] EMB_D[28] E
VDDA18 GP6[13] GP6[14]
GP4[15]
AMUTE1/ AFSX0/ UART1_TXD/ AXR0[6]/ AXR0[2]/
EMB_A[0]/ EMB_A[4]/ EMB_A[8]/ EMB_D[9]/ EMB_D[10]/ EMB_D[11]/ EMB_D[12]/
D PLL0_VDDA USB0_ID USB0_VBUS EHRPWMTZ/ GP2[13]/ AXR0[10]/ ACLKR2/ AXR2[3]/ EMB_CS[0] D
GP7[2] GP7[6] GP7[10] GP6[9] GP6[10] GP6[11] GP6[12]
GP4[14] BOOT[10] GP3[10] GP3[6] GP3[2]
ACLKX0/
UART1_RXD/ AXR0[5]/ AXR0[1]/ EMB_WE_
USB0_ AFSR0/ ECAP0/ EMB_BA[0]/ EMB_A[1]/ EMB_A[5]/ EMB_A[9]/ EMB_D[8]/
C NC NC AXR0[9]/ AFSX2/ ACLKX2/ EMB_SDCKE EMB_CLK DQM[1]/ C
VDDA12 GP3[12] APWM0/ GP7[1] GP7[3] GP7[7] GP7[11] GP6[8]
GP3[9] GP3[5] GP3[1] GP5[14]
GP2[12]
ACLKR0/ AHLKX0/
AHCLKX2/ AXR0[4]/ AXR0[0]/
ECAP1/ AXR0[8]/ EMB_BA[1]/ EMB_A[2]/ EMB_A[6]/ EMB_A[11]/ EMB_WE_ EMB_A[12]/
B RSV2 VSS VSS USB_ AXR2[1]/ AFSR2/ EMB_D[25] DVDD B
APWM1/ REFCLKIN/ GP3[8] GP7[0] GP7[4] GP7[8] GP7[13] DQM[2] GP3[13]
GP3[4] GP3[0]
GP2[15] GP2[11]
AHCLKR0/ AXR0[11]/ AXR0[3]/
AXR0[7]/ EMB_A[10]/ EMB_A[3]/ EMB_A[7]/ EMB_WE_
A VSS VSS VSS GP2[14]/ AXR2[0]/ AXR2[2]/ EMB_RAS EMB_D[24] EMB_D[26] VSS VSS A
GP3[7] GP3[3] GP7[12] GP7[5] GP7[9] DQM[3]
BOOT[11] GP3[11]
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
91
YSP-CU4300/YSP-CU3300/NS-WSW160
Pin TYPE PULL
Function Name Detail of Function
YSP-CU4300/YSP-CU3300/
No. (1) (2)
Device Reset and JTAG
NS-WSW160
G3 RESET I EMIFA Async chip select
L4 AMUTE0/ RESETOUT O (3) IPD Reset output. Multiplexed with McASP0 mute output.
J1 TMS I IPU JTAG test mode select
J2 TDI I IPU JTAG test data input
J3 TDO O IPD JTAG test data output
H3 TCK I IPU JTAG test clock
J4 TRST I IPD JTAG test reset
J5 EMU[0]/GP7[15] I/O IPU Miscellaneous emulation pin.
High-Frequency Oscillator and PLL
R12 EMA_CLK/OBSCLK/AHCLKR2/ GP1[15] O IPU PLL Observation Clock
F2 OSCIN I Oscillator input
F1 OSCOUT O Oscillator output
E2 OSCVSS GND Oscillator ground (for filter only)
D1 PLL0_VDDA PWR PLL analog VDD (1.2-V filtered supply)
E1 PLL0_VSSA GND PLL analog VSS (for filter)
Real-Time Clock and 32-kHz Oscillator
G1 RTC_CVDD PWR RTC module core power ( isolated from rest of chip CVDD)
H1 RTC_XI I Low-frequency (32-kHz) oscillator receiver for real-time clock
T
H2 RTC_XO O Low-frequency (32-kHz) oscillator driver for real-time clock
G2 RTC_VSS GND Oscillator ground (for filter)
F
External Memory Interface A (ASYNC, SDRAM)
M16 EMA_D[15]/UHPI_HD[15]/ GP0[15] I/O IPD EMIFA data bus
N14 EMA_D[14]/UHPI_HD[14]/GP0[14] I/O IPD
N16 EMA_D[13]/UHPI_HD[13]/GP0[13] I/O IPD
A
P14 EMA_D[12]/UHPI_HD[12]/GP0[12] I/O IPD
P16 EMA_D[11]/UHPI_HD[11]/GP0[11] I/O IPD
R14 EMA_D[10]/UHPI_HD[10]/GP0[10] I/O IPD
R
T14 EMA_D[9]/UHPI_HD[9]/GP0[9] I/O IPD
N12 EMA_D[8]/UHPI_HD[8]/GP0[8] I/O IPD
M15 EMA_D[7]/MMCSD_DAT[7]/UHPI_HD[7]/GP0[7]/ I/O IPU
D
BOOT[13]
N13 EMA_D[6]/MMCSD_DAT[6]/UHPI_HD[6]/GP0[6] I/O IPU
N15 EMA_D[5]/MMCSD_DAT[5]/UHPI_HD[5]/GP0[5] I/O IPU
P13 EMA_D[4]/MMCSD_DAT[4]/UHPI_HD[4]/GP0[4] I/O IPU
P15 EMA_D[3]/MMCSD_DAT[3]/UHPI_HD[3]/GP0[3] I/O IPU
R13 EMA_D[2]/MMCSD_DAT[2]/UHPI_HD[2]/GP0[2] I/O IPU
R15 EMA_D[1]/MMCSD_DAT[1]/UHPI_HD[1]/GP0[1] I/O IPU
T13 EMA_D[0]/MMCSD_DAT[0]/UHPI_HD[0]/GP0[0]/ I/O IPU
BOOT[12]
External Memory Interface A (EMIFA) Terminal Functions (continued)
N11 EMA_A[12]/ GP1[12] O IPU EMIFA address bus
P11 EMA_A[11]/ GP1[11] O IPU
N8 EMA_A[10]/ GP1[10] O IPU
R11 EMA_A[9]/ GP1[9] O IPU
T11 EMA_A[8]/ GP1[8] O IPU
N10 EMA_A[7]/ GP1[7] O IPD
P10 EMA_A[6]/ GP1[6] O IPD
R10 EMA_A[5]/ GP1[5] O IPD
T10 EMA_A[4]/ GP1[4] O IPD
N9 EMA_A[3]/ GP1[3] O IPD
P9 EMA_A[2]/MMCSD_CMD/UHPI_HCNTL1/GP1[2] O IPU
R9 EMA_A[1]/MMCSD_CLK/UHPI_HCNTL0/GP1[1] O IPU
T9 EMA_A[0]/ GP1[0] O IPD
P8 EMA_BA[1]/ UHPI_HHWIL/GP1[13] O IPU EMIFA bank address
R8 EMA_BA[0]/ GP1[14] O IPU
R12 EMA_CLK/OBSCLK/AHCLKR2/GP1[15] O IPU EMIFA clock
T12 EMA_SDCKE/GP2[0] O IPU EMIFA SDRAM clock enable
N7 EMA_RAS /EMA_CS[5]/GP2[2] O IPU EMIFA SDRAM row address strobe
L16 EMA_CAS /EMA_CS[4]/GP2[1] O IPU EMIFA SDRAM column address strobe
N7 EMA_RAS/ EMA_CS[5] /GP2[2] O IPU EMIFA Async chip select
L16 EMA_CAS/ EMA_CS[4] /GP2[1] O IPU
T7 EMA_CS[3] /AMUTE2/GP2[6] O IPU
P7 EMA_CS[2] /UHPI_HCS/GP2[5]/BOOT[15] O IPU
T8 EMA_CS[0] /UHPI_HAS/GP2[4] O IPU EMIFA SDRAM chip select
M13 EMA_WE /UHPI_HRW/AXR0[12]/GP2[3]/BOOT[14] O IPU EMIFA SDRAM write enable
P12 EMA_WE_DQM[1] /UHPI_HDS2/AXR0[14]/GP2[8] O IPU EMIFA write enable/data mask for EMA_D[15:8]
92
YSP-CU4300/YSP-CU3300/NS-WSW160
Pin TYPE PULL
Function Name Detail of Function
YSP-CU4300/YSP-CU3300/
No. (1) (2)
M14 EMA_WE_DQM[0] /UHPI_HINT/AXR0[15]/GP2[9] O IPU EMIFA write enable/data mask for EMA_D[7:0]
NS-WSW160
R7 EMA_OE /UHPI_HDS1/AXR0[13]/GP2[7] O IPU EMIFA output enable
N6 EMA_WAIT[0]/ UHPI_HRDY/GP2[10] I IPU EMIFA wait input/interrupt
External Memory Interface B (only SDRAM )
G14 EMB_D[31] I/O IPD EMIFB SDRAM data bus
F15 EMB_D[30] I/O IPD
F14 EMB_D[29] I/O IPD
E15 EMB_D[28] I/O IPD
E14 EMB_D[27] I/O IPD
A14 EMB_D[26] I/O IPD
B14 EMB_D[25] I/O IPD
A13 EMB_D[24] I/O IPD
L15 EMB_D[23] I/O IPD
L14 EMB_D[22] I/O IPD
K16 EMB_D[21] I/O IPD
K13 EMB_D[20] I/O IPD
J14 EMB_D[19] I/O IPD
H15 EMB_D[18] I/O IPD
H14 EMB_D[17] I/O IPD
T
G15 EMB_D[16] I/O IPD
F13 EMB_D[15]/GP6[15] I/O IPD
F
E16 EMB_D[14]/GP6[14] I/O IPD
E13 EMB_D[13]/GP6[13] I/O IPD
D16 EMB_D[12]/GP6[12] I/O IPD
D15 EMB_D[11]/GP6[11] I/O IPD
A
D14 EMB_D[10]/GP6[10] I/O IPD
D13 EMB_D[9]/GP6[9] I/O IPD
C16 EMB_D[8]/GP6[8] I/O IPD
R
J16 EMB_D[7]/GP6[7] I/O IPD
J15 EMB_D[6]/GP6[6] I/O IPD
J13 EMB_D[5]/GP6[5] I/O IPD
D
H16 EMB_D[4]/GP6[4] I/O IPD
H13 EMB_D[3]/GP6[3] I/O IPD
G16 EMB_D[2]/GP6[2] I/O IPD
G13 EMB_D[1]/GP6[1] I/O IPD
F16 EMB_D[0]/GP6[0] I/O IPD
B15 EMB_A[12]/GP3[13] O IPD EMIFB SDRAM row/column address bus
B12 EMB_A[11]/GP7[13] O IPD
A9 EMB_A[10]/GP7[12] O IPD
C12 EMB_A[9]/GP7[11] O IPD
D12 EMB_A[8]/GP7[10] O IPD
A11 EMB_A[7]/GP7[9] O IPD
B11 EMB_A[6]/GP7[8] O IPD
C11 EMB_A[5]/GP7[7] O IPD
D11 EMB_A[4]/GP7[6] O IPD EMIFB SDRAM row/column address
A10 EMB_A[3]/GP7[5] O IPD
B10 EMB_A[2]/GP7[4] O IPD
C10 EMB_A[1]/GP7[3] O IPD
D10 EMB_A[0]/GP7[2] O IPD
B9 EMB_BA[1]/GP7[0] O IPU EMIFB SDRAM bank address
C9 EMB_BA[0]/GP7[1] O IPU
C14 EMB_CLK O IPU EMIF SDRAM clock
C13 EMB_SDCKE I/O IPU EMIFB SDRAM clock enable
K15 EMB_WE O IPU EMIFB write enable
A8 EMB_RAS O IPU EMIFB SDRAM row address strobe
L13 EMB_CAS O IPU EMIFB column address strobe
D9 EMB_CS[0] O IPU EMIFB SDRAM chip select 0
A12 EMB_WE_DQM[3] O IPU EMIFB write enable/data mask for EMB_D
B13 EMB_WE_DQM[2] O IPU
C15 EMB_WE_DQM[1] /GP5[14] O IPU
K14 EMB_WE_DQM[0] /GP5[15] O IPU
Serial Peripheral Interface Modules (SPI0, SPI1)
N4 SPI0_SCS[0] /UART0_RTS/EQEP0B/GP5[4]/ I/O IPU SPI0 chip select
BOOT[4]
R5 SPI0_ENA /UART0_CTS/EQEP0A/GP5[3]/BOOT[3] I/O IPU SPI0 enable
T5 SPI0_CLK/EQEP1I/GP5[2]/BOOT[2] I/O IPD SPI0 clock
P6 SPI0_SIMO[0]/EQEP0S/GP5[1]/BOOT[1] I/O IPD SPI0 data/slave-in-master-out
93
YSP-CU4300/YSP-CU3300/NS-WSW160
Pin TYPE PULL
Function Name Detail of Function
YSP-CU4300/YSP-CU3300/
No. (1) (2)
R6 SPI0_SOMI[0]/EQEP0I/GP5[0]/BOOT[0] I/O IPD SPI0 data/slave-out-master-in
NS-WSW160
P4 SPI1_SCS[0] /UART2_TXD/GP5[13] I/O IPU SPI1 chip select
R4 SPI1_ENA /UART2_RXD/GP5[12] I/O IPU SPI1 enable
T6 SPI1_CLK/EQEP1S/GP5[7]/BOOT[7] I/O IPD SPI1 clock
N5 SPI1_SIMO[0]/I2C1_SDA/GP5[6]/BOOT[6] I/O IPU SPI1 data/slave-in-master-out
P5 SPI1_SOMI[0]/I2C1_SCL/GP5[5]/BOOT[5] I/O IPU SPI1 data/slave-out-master-in
Enhanced Capture/Auxiliary PWM Modules (eCAP0, eCAP1, eCAP2)
C5 ACLKX0/ECAP0/APWM0/GP2[12] I/O IPD Enhanced capture 0/input or auxiliary PWM 0 output
B4 ACLKR0/ECAP1/APWM1/GP2[15] I/O IPD Enhanced capture 1/input or auxiliary PWM 1 output
L2 ACLKR1/ECAP2/APWM2/GP4[12] I/O IPD Enhanced capture 2/input or auxiliary PWM 2 output
Enhanced Pulse Width Modulators (eHRPWM0, eHRPWM1, eHRPWM2)
K3 ACLKX1/EPWM0A/GP3[15] I/O IPD eHRPWM0 A output
K2 AHCLKX1/EPWM0B/GP3[14] I/O IPD eHRPWM0 B output
D4 AMUTE1/EPWMTZ/GP4[14] I/O IPD eHRPWM0 trip zone input
K4 AFSX1/EPWMSYNCI/EPWMSYNCO/GP4[10] I/O IPD Sync input to eHRPWM0 module or sync output to external PWM
M2 AXR1[8]/EPWM1A/GP4[8] I/O IPD eHRPWM1 A (with high-resolution)
M3 AXR1[7]/EPWM1B/GP4[7] I/O IPD eHRPWM1 B
D4 AMUTE1/EPWMTZ/GP4[14] I/O IPD eHRPWM1 trip zone input
M4 AXR1[6]/EPWM2A/GP4[6] I/O IPD eHRPWM2 A (with high-resolution)
T
N1 AXR1[5]/EPWM2B/GP4[5] I/O IPD eHRPWM2 B
D4 AMUTE1/EPWMTZ/GP4[14] I/O IPD eHRPWM2 trip zone input
F
Enhanced Quadrature Encoder Pulse Module (eQEP)
R5 SPI0_ENA/UART0_CTS/EQEP0A/GP5[3]/ I IPU eQEP0A quadrature input
BOOT[3]
N4 SPI0_SCS[0]/UART0_RTS/EQEP0B/GP5[4]/ I IPU eQEP0B quadrature input
A
BOOT[4]
R6 SPI0_SOMI[0]/EQEP0I/GP5[0]/BOOT[0] I IPD eQEP0 index
P6 SPI0_SIMO[0]/EQEP0S/GP5[1]/BOOT[1] I IPD eQEP0 strobe
R
P1 AXR1[3]/EQEP1A/GP4[3] I IPD eQEP1A quadrature input
N2 AXR1[4]/EQEP1B/GP4[4] I IPD eQEP1B quadrature input
T5 SPI0_CLK/EQEP1I/GP5[2]/BOOT[2] I IPD eQEP1 index
D
T6 SPI1_CLK/EQEP1S/GP5[7]/BOOT[7] I IPD eQEP1 strobe
Boot
P7 EMA_CS[2]/UHPI_HCS/GP2[5]/BOOT[15] I IPU BOOT[15]
M13 EMA_WE/UHPI_HRW/AXR0[12]/GP2[3]/BOOT[14] I IPU BOOT[14]
M15 EMA_D[7]/MMCSD_DAT[7]/UHPI_HD[7]/GP0[7]/ I IPU BOOT[13]
BOOT[13]
T13 EMA_D[0]/MMCSD_DAT[0]/UHPI_HD[0]/GP0[0]/ I IPU BOOT[12]
BOOT[12]
A4 AHCLKR0/GP2[14]/BOOT[11] I IPD BOOT[11]
D5 AFSX0/GP2[13]/BOOT[10] I IPD BOOT[10]
P3 UART0_TXD/I2C0_SCL/TM64P0_OUT12/GP5[9]/ I IPU BOOT[9]
BOOT[9]
R3 UART0_RXD/I2C0_SDA/TM64P0_IN12/GP5[8]/ I IPU BOOT[8]
BOOT[8]
T6 SPI1_CLK/EQEP1S/GP5[7]/BOOT[7] I IPD BOOT[7]
N5 SPI1_SIMO[0]/I2C1_SDA/GP5[6]/BOOT[6] I IPU BOOT[6]
P5 SPI1_SOMI[0]/I2C1_SCL/GP5[5]/BOOT[5] I IPU BOOT[5]
N4 SPI0_SCS[0]/UART0_RTS/EQEP0B/GP5[4]/ I IPU BOOT[4]
BOOT[4]
R5 SPI0_ENA/UART0_CTS/EQEP0A/GP5[3]/ I IPU BOOT[3]
BOOT[3]
T5 SPI0_CLK/EQEP1I/GP5[2]/BOOT[2] I IPD BOOT[2]
P6 SPI0_SIMO[0]/EQEP0S/GP5[1]/BOOT[1] I IPD BOOT[1]
R6 SPI0_SOMI[0]/EQEP0I/GP5[0]/BOOT[0] I IPD BOOT[0]
Universal Asynchronous Receiver/Transmitters (UART0, UART1, UART2)
R3 UART0_RXD/I2C0_SDA/TM64P0_IN12/GP5[8]/ I IPU UART0 receive data
BOOT[8]
P3 UART0_TXD/I2C0_SCL/TM64P0_OUT12/GP5[9]/ O IPU UART0 transmit data
BOOT[9]
N4 SPI0_SCS[0]/ UART0_RTS /EQEP0B/GP5[4]/ O IPU UART0 ready-to-send output
BOOT[4]
R5 SPI0_ENA/ UART0_CTS /EQEP0A/GP5[3]/ I IPU UART0 clear-to-send input
BOOT[3]
C6 UART1_RXD/AXR0[9]/GP3[9] (4) I IPD UART1 receive data
D6 UART1_TXD/AXR0[10]/GP3[10] (4) O IPD UART1 transmit data
R4 SPI1_ENA/UART2_RXD/GP5[12] I IPU UART2 receive data
P4 SPI1_SCS[0]/UART2_TXD/GP5[13] O IPU UART2 transmit data
94
YSP-CU4300/YSP-CU3300/NS-WSW160
Pin TYPE PULL
Function Name Detail of Function
YSP-CU4300/YSP-CU3300/
No. (1) (2)
Inter-Integrated Circuit Modules(I2C0, I2C1)
NS-WSW160
R3 UART0_RXD/I2C0_SDA/TM64P0_IN12/GP5[8]/ I/O IPU I2C0 serial data
BOOT[8]
P3 UART0_TXD/I2C0_SCL/TM64P0_OUT12/GP5[9]/ I/O IPU I2C0 serial clock
BOOT[9]
N5 SPI1_SIMO[0]/I2C1_SDA/GP5[6]/BOOT[6] I/O IPU I2C1 serial Data
P5 SPI1_SOMI[0]/I2C1_SCL/GP5[5]/BOOT[5] I/O IPU I2C1 serial clock
Timers
R3 UART0_RXD/I2C0_SDA/TM64P0_IN12/GP5[8]/ I IPU Timer0 lower input
BOOT[8]
P3 UART0_TXD/I2C0_SCL/TM64P0_OUT12/GP5[9]/ O IPU Timer0 lower output
BOOT[9]
Universal Host-Port Interface (UHPI)
M16 EMA_D[15]/UHPI_HD[15]/GP0[15] I/O IPD UHPI data bus
N14 EMA_D[14]/UHPI_HD[14] /GP0[14] I/O IPD
N16 EMA_D[13]/UHPI_HD[13] /GP0[13] I/O IPD
P14 EMA_D[12]/UHPI_HD[12] GP0[12] I/O IPD
P16 EMA_D[11]/UHPI_HD[11] /GP0[11] I/O IPD
R14 EMA_D[10]/UHPI_HD[10] GP0[10] I/O IPD
T
T14 EMA_D[9]/UHPI_HD[9] /GP0[9] I/O IPD
N12 EMA_D[8]/UHPI_HD[8] /GP0[8] I/O IPD
F
M15 EMA_D[7]/MMCSD_DAT[7]/UHPI_HD[7]/GP0[7]/ I/O IPU
BOOT[13]
N15 EMA_D[6]/MMCSD_DAT[6]/UHPI_HD[6]/GP0[6] I/O IPU
N15 EMA_D[5]/MMCSD_DAT[5]/UHPI_HD[5]/GP0[5] I/O IPU
A
P13 EMA_D[4]/MMCSD_DAT[4]/UHPI_HD[4]/GP0[4] I/O IPU
P15 EMA_D[3]/MMCSD_DAT[3]/UHPI_HD[3]/GP0[3] I/O IPU
R13 EMA_D[2]/MMCSD_DAT[2]/UHPI_HD[2]/GP0[2] I/O IPU
R
R15 EMA_D[1]/MMCSD_DAT[1]/UHPI_HD[1]/GP0[1] I/O IPU
T13 EMA_D[0]/MMCSD_DAT[0]/UHPI_HD[0]/GP0[0]/ I/O IPU
BOOT[12]
D
P9 EMA_A[2]/MMCSD_CMD/UHPI_HCNTL1/GP1[2] I/O IPU UHPI access control
R9 EMA_A[1]/MMCSD_CLK/UHPI_HCNTL0/GP1[1] I/O IPU
P8 EMA_BA[1]/UHPI_HHWIL/GP1[13] I/O IPU UHPI half-word identification control
M13 EMA_WE/UHPI_HRW /AXR0[12]/GP2[3]/ I/O IPU UHPI read/write
BOOT[14]
P7 EMA_CS[2]/ UHPI_HCS /GP2[5]/BOOT[15] I/O IPU UHPI chip select
P12 EMA_WE_DQM[1]/ UHPI_HDS2 /AXR0[14]/ I/O IPU UHPI data strobe
GP2[8]
R7 EMA_OE/ UHPI_HDS1 /AXR0[13]/GP2[7] I/O IPU
M14 EMA_WE_DQM[0]/ UHPI_HINT /AXR0[15]/GP2[9] I/O IPU UHPI host interrupt
N6 EMA_WAIT[0]/ UHPI_HRDY /GP2[10] I/O IPU UHPI ready
T8 EMA_CS[0]/ UHPI_HAS /GP2[4] I/O IPU UHPI address strobe
Multichannel Audio Serial Ports (McASP0, McASP1, McASP2)
M14 EMA_WE_DQM[0]/UHPI_HINT/AXR0[15]/GP2[9] I/O IPU McASP0 serial data
P12 EMA_WE_DQM[1]/UHPI_HDS2/AXR0[14]/GP2[8] I/O IPU
R7 EMA_OE/UHPI_HDS1/AXR0[13]/GP2[7] I/O IPU
M13 EMA_WE/UHPI_HRW/AXR0[12]/GP2[3]/BOOT[14] I/O IPU
A5 AXR0[11]/ AXR2[0]/GP3[11] I/O IPD
D6 AXR0[10]/GP3[10] I/O IPD
C6 UART1_RXD/AXR0[9]/GP3[9] I/O IPD
B6 AXR0[8]/GP3[8] I/O IPU
A6 AXR0[7]/GP3[7] I/O IPD
D7 AXR0[6]/ACLKR2/GP3[6] I/O IPD
C7 AXR0[5]/AFSX2/GP3[5] I/O IPD
B7 AXR0[4]/ AXR2[1]/GP3[4] I/O IPD
A7 AXR0[3]/AXR2[2]/GP3[3] I/O IPD
D8 AXR0[2]/AXR2[3]/GP3[2] I/O IPD
C8 AXR0[1]/ACLKX2/GP3[1] I/O IPD
B8 AXR0[0]/AFSR2/GP3[0] I/O IPD
B5 AHCLKX0/AHCLKX2/USB_REFCLKIN/GP2[11] I/O IPD McASP0 transmit master clock
C5 ACLKX0/ECAP0/APWM0/GP2[12] I/O IPD McASP0 transmit bit clock
D5 AFSX0/GP2[13]/BOOT[10] I/O IPD McASP0 transmit frame sync
A4 AHCLKR0/GP2[14]/BOOT[11] I/O IPD McASP0 receive master clock
B4 ACLKR0/ECAP1/APWM1/GP2[15] I/O IPD McASP0 receive bit clock
C4 AFSR0/GP3[12] I/O IPD McASP0 receive frame sync
L4 AMUTE0/RESETOUT - O IPD McASP0 mute output
95
YSP-CU4300/YSP-CU3300/NS-WSW160
Pin TYPE PULL
Function Name Detail of Function
YSP-CU4300/YSP-CU3300/
No. (1) (2)
T4 AXR1[11]/GP5[11] I/O IPU McASP1 serial data
NS-WSW160
N3 AXR1[10]/GP5[10] I/O IPU
M1 AXR1[9]/GP4[9] I/O IPD
M2 AXR1[8]/EPWM1A/GP4[8] I/O IPD
M3 AXR1[7]/EPWM1B/GP4[7] I/O IPD
M4 AXR1[6]/EPWM2A/GP4[6] I/O IPD
N1 AXR1[5]/EPWM2B/GP4[5] I/O IPD
N2 AXR1[4]/EQEP1B/GP4[4] I/O IPD
P1 AXR1[3]/EQEP1A/GP4[3] I/O IPD
P2 AXR1[2]/GP4[2] I/O IPD
R2 AXR1[1]/GP4[1] I/O IPD
T3 AXR1[0]/GP4[0] I/O IPD
K2 AHCLKX1/EPWM0B/GP3[14] I/O IPD McASP1 transmit master clock
K3 ACLKX1/EPWM0A/GP3[15] I/O IPD McASP1transmit bit clock
K4 AFSX1/EPWMSYNCI/EPWMSYNCO/GP4[10] I/O IPD McASP1 transmit frame sync
L1 AHCLKR1/GP4[11] I/O IPD McASP1 receive master clock
L2 ACLKR1/ECAP2/APWM2/GP4[12] I/O IPD McASP1 receive bit clock
L3 AFSR1/GP4[13] I/O IPD McASP1 receive frame sync
D4 AMUTE1/EPWMTZ/GP4[14] O IPD McASP1 mute output
T
B8 AXR0[0]/AFSR2/GP3[0] O IPD McASP2 serial data
D8 AXR0[2]/ AXR2[3]/GP3[2] O IPD
F
A7 AXR0[3]/ AXR2[2]/GP3[3] O IPD
B7 AXR0[4]/ AXR2[1]/GP3[4] O IPD
A5 AXR0[11]/AXR2[0]/GP3[11] O IPD
B5 AHCLKX0/AHCLKX2/USB_REFCLKIN/GP2[11] O IPD McASP2 transmit master clock
A
C8 AXR0[1]/ ACLKX2/GP3[1] O IPD McASP2 transmit bit clock
C7 AXR0[5]/ AFSX2/GP3[5] O IPD McASP2 transmit frame sync
R12 EMA_CLK/OBSCLK/AHCLKR2/GP1[15] O IPU McASP2 receive master clock
R
D7 AXR0[6]/ ACLKR2/GP3[6] I/O IPD McASP2 receive bit clock
T7 EMA_CS[3]/AMUTE2/GP2[6] O IPU McASP2 mute output
Universal Serial Bus Module (USB0)
D
G4 USB0_DM A USB0 PHY data minus
F4 USB0_DP A USB0 PHY data plus
H5 USB0_VDDA33 PWR USB0 PHY 3.3-V supply
E3 USB0_VDDA18 PWR USB0 PHY 1.8-V supply input
C3 USB0_VDDA12 (5) PWR USB0 PHY 1.2-V LDO output for bypass cap
D2 USB0_ID A USB0 PHY identification (mini-A or mini-B plug)
D3 USB0_VBUS A USB0 bus voltage
E4 USB0_DRVVBUS/GP4[15] O IPD USB0 controller VBUS control output
Multiplexed with GPIO bank 4 pin 15
B5 AHCLKX0/AHCLKX2/USB_REFCLKIN/GP2[11] I IPD USB_REFCLKIN. Optional 48 MHz clock input
Multimedia Card/Secure Digital (MMC/SD)
R9 EMA_A[1]/MMCSD_CLK/UHPI_HCNTL0/GP1[1] O IPU MMCSD_CLK
P9 EMA_A[2]/MMCSD_CMD/UHPI_HCNTL1/GP1[2] I/O IPU MMCSD_CMD
M15 EMA_D[7]/MMCSD_DAT[7]/UHPI_HD[7]/GP0[7]/ I/O IPU MMC/SD data
BOOT[13]
N13 EMA_D[6]/MMCSD_DAT[6]/UHPI_HD[6]/GP0[6] I/O IPU
N15 EMA_D[5]/MMCSD_DAT[5]/UHPI_HD[5]/GP0[5] I/O IPU
P13 EMA_D[4]/MMCSD_DAT[4]/UHPI_HD[4]/GP0[4] I/O IPU
P15 EMA_D[3]/MMCSD_DAT[3]/UHPI_HD[3]/GP0[3] I/O IPU
R13 EMA_D[2]/MMCSD_DAT[2]/UHPI_HD[2]/GP0[2] I/O IPU
R15 EMA_D[1]/MMCSD_DAT[1]/UHPI_HD[1]/GP0[1] I/O IPU
T13 EMA_D[0]/MMCSD_DAT[0]/UHPI_HD[0]/GP0[0]/ I/O IPU
BOOT[12]
General-Purpose IO Only Terminal Functions
K1 GP7[14] (6) I/O IPD General-Purpose IO signal
Reserved and No-connect
F7 RSV1 – – Reserved
(Leave unconnected, do not connect to power or ground)
B1 RSV2 PWR – Reserved
For proper device operation, this pin must be tied directly to CVDD
H4 NC – – –
F3 NC – – –
C1 NC – – –
C2 NC – – –
96
YSP-CU4300/YSP-CU3300/NS-WSW160
Pin TYPE PULL
Function Name Detail of Function
YSP-CU4300/YSP-CU3300/
No. (1) (2)
Supply and Ground
NS-WSW160
F6 CVDD (Core supply) PWR – 1.2-V core supply voltage pins
G6 CVDD (Core supply) PWR –
G7 CVDD (Core supply) PWR –
G10 CVDD (Core supply) PWR –
G11 CVDD (Core supply) PWR –
H6 CVDD (Core supply) PWR –
H7 CVDD (Core supply) PWR –
H10 CVDD (Core supply) PWR –
H11 CVDD (Core supply) PWR –
H12 CVDD (Core supply) PWR –
J6 CVDD (Core supply) PWR –
J7 CVDD (Core supply) PWR –
J10 CVDD (Core supply) PWR –
J11 CVDD (Core supply) PWR –
J12 CVDD (Core supply) PWR –
K6 CVDD (Core supply) PWR –
K7 CVDD (Core supply) PWR –
K10 CVDD (Core supply) PWR –
T
K11 CVDD (Core supply) PWR –
L6 CVDD (Core supply) PWR –
F
B16 DVDD (I/O supply) PWR – 3.3-V I/O supply voltage pins
E5 DVDD (I/O supply) PWR –
E8 DVDD (I/O supply) PWR –
E9 DVDD (I/O supply) PWR –
A
E12 DVDD (I/O supply) PWR –
F5 DVDD (I/O supply) PWR –
F11 DVDD (I/O supply) PWR –
R
F12 DVDD (I/O supply) PWR –
G5 DVDD (I/O supply) PWR –
G12 DVDD (I/O supply) PWR –
D
K5 DVDD (I/O supply) PWR –
K12 DVDD (I/O supply) PWR –
L5 DVDD (I/O supply) PWR –
L11 DVDD (I/O supply) PWR –
L12 DVDD (I/O supply) PWR –
M5 DVDD (I/O supply) PWR –
M8 DVDD (I/O supply) PWR –
M9 DVDD (I/O supply) PWR –
M12 DVDD (I/O supply) PWR –
R1 DVDD (I/O supply) PWR –
R16 DVDD (I/O supply) PWR –
A1 VSS (Ground) GND – Ground pins
A2 VSS (Ground) GND –
A3 VSS (Ground) GND –
A15 VSS (Ground) GND –
A16 VSS (Ground) GND –
B2 VSS (Ground) GND –
B3 VSS (Ground) GND –
E6 VSS (Ground) GND –
E7 VSS (Ground) GND –
E10 VSS (Ground) GND –
E11 VSS (Ground) GND –
F8 VSS (Ground) GND –
F9 VSS (Ground) GND –
F10 VSS (Ground) GND –
G8 VSS (Ground) GND –
G9 VSS (Ground) GND –
H8 VSS (Ground) GND –
H9 VSS (Ground) GND –
J8 VSS (Ground) GND –
J9 VSS (Ground) GND –
K8 VSS (Ground) GND –
K9 VSS (Ground) GND –
L7 VSS (Ground) GND –
L8 VSS (Ground) GND –
L9 VSS (Ground) GND –
97
YSP-CU4300/YSP-CU3300/NS-WSW160
Pin TYPE PULL
Function Name Detail of Function
YSP-CU4300/YSP-CU3300/
No. (1) (2)
L10 VSS (Ground) GND – Ground pins
NS-WSW160
M6 VSS (Ground) GND –
M7 VSS (Ground) GND –
M10 VSS (Ground) GND –
M11 VSS (Ground) GND –
T1 VSS (Ground) GND –
T2 VSS (Ground) GND –
T15 VSS (Ground) GND –
T16 VSS (Ground) GND –
(1) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.
Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name
highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the
configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where
functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral.
(2) IPD = Internal Pull-down resistor, IPU = Internal Pull-up resistor
(3) Open drain mode for RESETOUT function.
T
(4) As these signals are internally pulled down while the device is in reset, it is necessary to externally pull them high with resistors if
UART1 boot mode is used.
F
(5) Core power supply LDO output for USB PHY. This pin must be connected via a 0.22 -uF capacitor to VSS. When the USB peripheral is
not used, the USB_VDDA12 signal should still be connected via a 1-uF capacitor to VSS.
A
(6) GP7[14] is initially configured as a reserved function after reset and will not be in a predictable state. This signal will only be stable after
the GPIO configuration for this pin has been completed. Users should carefully consider the system implications of this pin being in an
unknown state after reset.
D R
98
YSP-CU4300/YSP-CU3300/NS-WSW160
IC701: TMPM362F10FG (DIGITAL P.C.B.)
YSP-CU4300/YSP-CU3300/
32-bit RISC microprocessor
* No replacement part available. / サービス部品供給なし
NS-WSW160
ETM Cortex-M3 DMA
SWD NVIC Controller
AHB Lite Bus Matrix
FLASH (1MB)
CG
RAM (56KB) PORT
Backup RAM WDT
(8KB)
RTC
AHB to I/O Bridge
AHB Lite Bus 0
16bit Timer
SMC
T
SIO/UART
(4byte FIFO)
I2C/SIO
F
10bit ADC
BOOT ROM CEC
A
RMC
KWUP
R
AHB to APB Bridge
SSP
D
21 D4_N_DISABLE
12 PWM_N_MUTE
13 D4_N_WARNG
14 AC_PDN_DET
10 TUNER_GPIO
9 PWM_N_PDN
11 PWM_N_RST
31 DSP1_N_INT
25 FLASH_RXD
23 FLASH_RXD
35 DSP1_N_CS
24 FLASH_TXD
34 DIR_N_RST
2 TI_WARNG
29 DSP_MISO
28 DSP_MOSI
27 DIR_N_INT
20 D4_N_RST
7 PWM_SDA
33 DIR_N_CS
26 232C_CTS
8 PWM_SCL
32 D4_N_IRQ
36 AW_MOSI
30 DSP_SCK
5 N_RESET
19 D4_N_CS
18 D4_MISO
17 D4_MOSI
22 D4_PON
16 D4_SCK
4 VREFH
6 MODE
15 DVss
3 AVss
1
AW_MISO 37 144 DSP_PRT
DSP1_N_RST 38 143 DC_PRT
USB_N_INT 39 142 26V_PRI
DSP1_N_RDY 40 141 DAMP_PRT
DSP1_FMT 41 140 DEST_N_WR
USB_MOSI 42 139 DIR_WCK2
USB_MISO 43 138 MODEL
USB_SCK 44 137
USB_N_CS 45 136 AW_PRT
46 135 HDMI_PRT
DVcc3 47 134
DVss 48 133 VBUS_PRT
49 132 INPUT_PRT
AW_FS_N_O 50
MICROPROCESSOR 131 KEY1
51 130 AVcc
AW_RX_EN 52 129 HDMI_CEC
AW_TX_EN 53 128 FLASH_N_BOOT
54 127 TEST2
I2S_SEL 55
TMPM362F10FG 126 TEST1
USB_N_RST 56 125 NMin
USB_BUSY 57 124 P_CON
USB_MCHNG 58 123 232C_RTS
USB_IPLERR 59 122 REGVss
USB_SEARCH 60
IC701 121 DVcc3
APL_N_RST 61 120 X2
APL_N_CS 62 119 CVss
P-GOOD 63 118 X1
64 117 CVcc3
65 116 XT2
66 115 XT1
67 114 REGVcc3
68 113 HDMI_MUTE
CEC_CHECK 69 112 HDMI_N_RST
70 111 HDMI_SCL
71 110 HDMI_SDA
PWR_N_LED 72 109 HDMI_PON3
MIC_N_DET 100
STBY_SW 101
TUN_N_RST 102
HDSUR_LED 103
AW_PON 104
HDMI_N_INT 105
OSD_WRITE 106
HDMI_PON1 107
HDMI_PON2 108
FL_PON 73
SDSUR_N_LED 74
SW_N_MUTE 75
E2P_N_CS 76
E2P_MOSI 77
E2P_MISO 78
E2P_SCK 79
AW_FS_I 80
ISEL_CNT1 81
ISEL_CNT2 82
FL_N_RST 83
FL_N_CS 84
FL_MOSI 85
FLASHER_PON 86
FL_SCK 87
REM_IN 88
DVcc3 89
DVss 90
SWD_IO 91
SWD_SCK 92
93
SWD_SWV 94
S3.3_2_PON1 95
USB_FLG 96
USB_PON 97
TUN_USB_SDA 98
TUN_USB_SCL 99
99
YSP-CU4300/YSP-CU3300/NS-WSW160
I/O
YSP-CU4300/YSP-CU3300/
When Apply Current
[Stby AW] / (iPod)
NS-WSW160
Stby HDMI /
[Stby CEC]
Function
Power On
Standby /
Pin
Port Name Name Detail of Function
No.
(P.C.B.)
1 PK6 DIR_SDO2 I I CDDA writing data input
PK6/AN14
2 PK7 TI_WARNG I+ HiZ DAMP error detect input
PK7/AN15 P.U to +3.3D
3 AVSS AVSS MCU MCU MCU
4 VREFH VREFH MCU
5 RESETn N_RESET MCU uCOM RESET input / Processed in microprocessor, usually pull-up
6 MODE MODE MCU Connected to GND / Processed in microprocessor, usually pull-up
7 SDA0 / PL0/ PWM_SDA SIO HiZ PWM_MOD I2C data input/output
SDA0/TB0OUT P.U to +3.3D
8 SCL0 / PL1/ PWM_SCL SO HiZ PWM_MOD I2C data clock output
SCL0/TB1OUT P.U to +3.3D
T
9 PL2 PWM_N_PDN O O PWM_MOD power down output
PL2/SCK0/TB2OUT
F
10 INT0 TUNER_GPIO IRQ HiZ TUNER GPIO input (INT pulse 1uS:RDS/SEEK detect)
PL3/INT0/TB3OUT P.U to +3.3D
11 PL4 PWM_N_RST O O PWM_MOD reset output
PL4/TXD1/TB4OUT P.U to +3.3D
A
12 PL5 PWM_N_MUTE O O PWM_MOD mute output
PL5/RXD1/TB5OUT P.U to +3.3D
13 PL6 D4_N_WARNG I+ HiZ D4 protection / Processed in microprocessor, usually pull-up
R
PL6/SCLK1/TB6OUT/CTS1n P.U to +3.3D
14 INT1 AC_PON_DET IRQ IRQ AC Interrupt input to detect connection
PL7/INT1/TB7OUT
D
15 DVSS DVSS MCU MCU MCU
16 SCLK2 D4_SCK SO O D4 synchronous clock
PM0/SCLK2/TB1IN0/CTS2n
17 TXD2 D4_MOSI SO O D4 synchronous data output
PM1/TXD2/TB1IN1
18 RXD2 D4_MISO SI HiZ D4 synchronous data input
PM2/RXD2/ALARMn
19 PM3 D4_N_CS O O D4 chip select output
PM3/INT2
20 PM4 D4_N_RST O O D4 reset output
PM4/SCLK3/CTS3n
21 PM5 D4_N_DISABLE O O D4 PWM stop
PM5/TXD3
22 PM6 D4_PON O O D4 power ON/OFF
PM6/RXD3
23 INT3 FLASH_RXD IRQ IRQ FLASH_UART/232C (asynchronous communication) mode data input
PM7/INT3 (C1 interrupt) / Parallel input
24 TXD4 FLASH_TXD SO SO FLASH_UART/232C (asynchronous communication) mode data output
PN0/TXD4
25 RXD4 FLASH_RXD SI SI FLASH_UART/232C (asynchronous communication) mode data input
PN1/RXD4 Parallel input
26 PN2 232C_CTS I I 232C transmission enable input
PN2/SCLK4/TB2IN0/CTS4n
27 INT4 DIR_N_INT IRQ IRQ DIR interrupt input
PN3/INT4/TB2IN1/RMIN0
28 TXD5 DSP_MOSI SO O DSP/DIR synchronous data output
PN4/TXD5
29 RXD5 DSP_MISO SI HiZ DSP/DIR synchronous data input
PN5/RXD5
30 SCLK5 DSP_SCK SO O DSP/DIR synchronous clock
PN6/SCLK5/TBFIN0/CTS5n
31 INT8 DSP1_N_INT IRQ IRQ DSP1 interrupt input
PN7/INT8/TBFIN1/RMIN1
32 PO0 D4_N_IRQ I HiZ D4 IRQ input
PO0/TXD6/TB8OUT
33 PO1 DIR_N_CS O O DIR chip select output
PO1/RXD6/TB9OUT
100
YSP-CU4300/YSP-CU3300/NS-WSW160
I/O
YSP-CU4300/YSP-CU3300/
When Apply Current
[Stby AW] / (iPod)
NS-WSW160
Stby HDMI /
[Stby CEC]
Function
Power On
Standby /
Pin
Port Name Name Detail of Function
No.
(P.C.B.)
34 PO2 DIR_N_RST O O DIR reset output
PO2/SCLK6/TBAOUT/CTS6n
35 PO3 DSP1_N_CS O O DSP chip select output
PO3/INT9/TBBOUT
36 PO4 AW_MOSI SO SO AW asynchronous data output
PO4/TXD7/TBCOUT [SO]
37 PO5 AW_MISO SI SI AW asynchronous data input
PO5/RXD7/TBDOUT [SI]
38 PO6 DSP1_N_RST O O DSP reset output
PO6/SCLK7/TBEOUT/CTS7n
39 INTA USB_N_INT IRQ O USB HOST interrupt input
PO7/INTA/TBFOUT
T
40 PP0 DSP1_N_RDY I HiZ DSP READY signal input
PP0/CS2n
F
41 PP1 DSP1_FMT O O DSP mute output
PP1
42 SPDO USB_MOSI SO O USB/USB_FLASH/Apple certified chip synchronous signal output
PP2/BLS0n/SPDO
A
43 SPDI USB_MISO SI SI USB/USB_FLASH/Apple certified chip synchronous data input
PP3/BLS1n/SPDI
44 SPCLK USB_SCK O O USB/USB_FLASH/Apple certified chip synchronous signal clock output
R
PP4/WEn/SPCLK
45 SPFSS USB_N_CS O O Chip select for USB HOST
PP5/OEn/SPFSS
D
46 PP6 – HiZ HiZ
PP6/ALEn
47 DVCC3 DVCC3 MCU
48 DVSS DVSS MCU MCU MCU
49 PA0 – HiZ HiZ
PA0/D0/AD0
50 PA1 AW_FS_N_O I+ I+ AW GPIO input
PA1/D1/AD1 [I+]
51 PA2 – HiZ HiZ
PA2/D2/AD2
52 PA3 AW_RX_EN O O AW RX mode of I2S enable
PA3/D3/AD3 [O] (Simultaneous Low output with AW_TX_EN is inhibited.)
53 PA4 AW_TX_EN O O AW TX mode of I2S enable
PA4/D4/AD4 [O] (Simultaneous Low output with AW_TX_EN is inhibited.)
54 PA5 – HiZ HiZ
PA5/D5/AD5
55 PA6 I2S_SEL O O Output to select HDMI/DIR path
PA6/D6/AD6 P.U to +3.3D
56 PA7 USB_N_RST O O Reset output for USB host
PA7/D7/AD7
57 PB0 USB_BUSY I- HiZ BUSY input from USB host
PB0/D8/AD8
58 PB1 USB_MCHNG I HiZ Input to detect change of USB host music number
PB1/D9/AD9
59 PB2 USB_IPLERR I- HiZ USB host initial program download error
PB2/D10/AD10
60 PB3 USB_SEARCH I HiZ Input to detect USB host search condition
PB3/D11/AD11
61 PB4 APL_N_RST O O Reset output for Apple certified chip
PB4/D12/AD12
62 PB5 APL_N_CS O O Chip select for Apple certified chip
PB5/D13/AD13
63 PB6 P-GOOD O O P-GOOD
PB6/D14/AD14
64 PB7 – HiZ HiZ
PB7/D15/AD15
101
YSP-CU4300/YSP-CU3300/NS-WSW160
I/O
YSP-CU4300/YSP-CU3300/
When Apply Current
[Stby AW] / (iPod)
NS-WSW160
Stby HDMI /
[Stby CEC]
Function
Power On
Standby /
Pin
Port Name Name Detail of Function
No.
(P.C.B.)
65 TXD8 – HiZ HiZ
PC0/A0/TXD8
66 RXD8 – HiZ HiZ
PC1/A1/RXD8
67 SCLK8 – HiZ HiZ
PC2/A2/SCLK8/CTS8n
68 PC3 – HiZ HiZ
PC3/A3
69 TXD9 CEC_CHECK I HiZ For CEC loop back test
PC4/A4/TXD9
70 RXD9 – HiZ HiZ
PC5/A5/RXD9
T
71 SCLK9 – HiZ HiZ
PC6/A6/SCLK9/CTS9n
F
72 PC7 PWR_N_LED O HiZ Output to control power ON LED
PC7/A7
73 PD0 FL_PON O HiZ ON/OFF of FL power generation +12D
PD0/A8/TXDA
A
74 PD1 SDSUR_N_LED O HiZ SD surround LED (orange) output (Low active)
PD1/A9/RXDA
75 PD2 SW_N_MUTE O O SW mute output
R
PD2/A10/SCLKA/CTSAn
76 PD3 E2P_N_CS O O E2P ROM chip select output
PD3/A11
D
77 TXDB E2P_MOSI SO SO E2P ROM synchronous data output
PD4/A12/TXDB
78 RXDB E2P_MISO SI SI E2P ROM synchronous data input
PD5/A13/RXDB
79 SCLKB E2P_SCK SO SO E2P ROM synchronous clock output
PD6/A14/SCLKB/CTSBn
80 PD7 AW_FS_I O O [O] AW GPIO output
PD7/A15/INTB
81 PE0 ISEL-CNT1 O O Output-1 to control input selector
PE0/A16/TB5IN0
82 PE1 ISEL-CNT2 O O Output-2 to control input selector
PE1/A17/TB5IN1
83 PE2 FL_N_RST O O (O) FL driver reset output
PE2/A18/TB6IN0
84 PE3 FL_N_CS O O (O) FL driver chip select output
PE3/A19/TB6IN1
85 PE4 FL_MOSI SO O FL synchronous signal output
PE4/A20/TXD0
86 PE5 FLASHER_PON O O IR_FLASHER control output
PE5/A21/RXD0
87 PE6 FL_SCK SO O FL synchronous signal clock output
PE6/A22/SCLK0/CTS0n
88 INT5 REM_IN IRQ IRQ Remote control interrupt input
PE7/INT5/SCOUT
89 DVCC3 DVCC3 MCU
90 DVSS DVSS MCU MCU MCU
91 SWDIO SWD_IO SIO SIO SWD data input/output
SWDIO Processed in microprocessor, usually pull-up
92 SWCLK SWD_SCK SIO SIO SWD clock input/output
SWCLK Processed in microprocessor, usually pull-up
93 PF0 – HiZ HiZ I2S spare for switching
PF0/TRACECLK
94 SWV SWD_SWV SO SO SWD SWV
PF1/TRACEDATA0/SWV
95 PF2 S3.3_2_PON1 O O S3.3 output-1 to control bleeder resistor
PF2/TRACEDATA1
102
YSP-CU4300/YSP-CU3300/NS-WSW160
I/O
YSP-CU4300/YSP-CU3300/
When Apply Current
[Stby AW] / (iPod)
NS-WSW160
Stby HDMI /
[Stby CEC]
Function
Power On
Standby /
Pin
Port Name Name Detail of Function
No.
(P.C.B.)
96 PF3 USB_FLG I HiZ USB excess current detect input (High side SW)
PF3/TRACEDATA2
97 PF4 USB_PON O O USB power control output
PF4/TRACEDATA3
98 PG0 TUN_USB_SDA SIO O TUNER/USB HOST I2C data input/output
PG0/SDA1/TB7IN0 Apple spare
99 PG1 TUN_USB_SCL SO O TUNER/USB HOST I2C clock output
PG1/SCL1/TB7IN1 Apple spare
100 PG2 MIC_N_DET I+ HiZ Microphone connection detect input
PG2/SCK1/CS0n
101 INT6 STBY_SW IRQ IRQ Input to detect power ON/OFF switch
PG3/INT6/CS1
T
102 PG4 TUN_N_RST O O TUNER reset output
PG4/SDA2/TB9IN0 P.U to +3.3D
F
103 PG5 HDSUR_LED O O HD surround LED (blue) output (High active)
PG5/SCL2/TB9IN1
104 PG6 AW_PON O O [O] AW power control output
PG6/SCK2/CS3n O
A
105 INT7 HDMI_N_INT IRQ O IRQ HDMI interrupt input
PG7/INT7/WDTOUTn
106 PH0 OSD_WRITE O O OSD_Flash write enable
R
PH0/SDA3/TBAIN0
107 PH1 HDMI_PON1 O O O HDMI power (5.0V) ON/OFF control output
PH1/SCL3/SI3/TBAIN0
D
108 PH2 HDMI_PON2 O O O HDMI power (1.3V) ON/OFF control output
PH2/SCK3/TBBIN0
109 PH3 HDMI_PON3 O O O HDMI power (3.3V) ON/OFF control output
PH3/INTC/TBBIN1
110 SDA4 HDMI_SDA SIO O SIO HDMI RX/TX I2C data input/output
PH4/SDA4/TBDIN0 P.U to +3.3H
111 SCL4 HDMI_SCL SO O SO HDMI RX/TX I2C clock output
PH5/SCL4/TBDIN1 P.U to +3.3H
112 PH6 HDMI_N_RST O O O HDMI reset output
PH6/SCK4/TBEIN0
113 INTD HDMI_MUTE IRQ O IRQ HDMI mute input
PH7/INTD/TBEIN1
114 REGVCC3 REGVCC3 MCU
115 XT1 XT1 MCU Low speed (32kHz) oscillator connection terminal (Input)
116 XT2 XT2 MCU Low speed (32kHz) oscillator connection terminal (Output)
117 CVCC3 CVCC3 MCU
118 X1 X1 MCU High speed (10MHz) oscillator connection terminal (Input)
119 CVSS CVSS MCU MCU MCU
120 X2 X2 MCU High speed (10MHz) oscillator connection terminal (Output)
121 DVCC3 DVCC3 MCU
122 REGVSS REGVSS MCU MCU MCU
123 PI2 232C_RTS O O 232C transmission request output
PI2/INTE Data input for CDDA writing (Spare)
124 PI3 P-CON O O Switching IC ON/OFF control input
PI3/INTF LR clock input for CDDA writing (Spare)
125 NMIn NMIn IRQ IRQ Processed in microprocessor, usually pull-up
126 TEST1 TEST1
127 TEST2 TEST2
128 BOOTn FLASH_N_BOOT I I FLASH single boot mode input, single boot mode at “L”
PI0/B00Tn
129 CEC HDMI_CEC SIO O SIO HDMI CEC data input/output
PI1/CEC
130 AVCC3 AVCC3 MCU
131 AIN0 KEY1 AD AD KEY input
PJ0/AIN0 * For CDDA writing mode
103
YSP-CU4300/YSP-CU3300/NS-WSW160
I/O
YSP-CU4300/YSP-CU3300/
When Apply Current
[Stby AW] / (iPod)
NS-WSW160
Stby HDMI /
[Stby CEC]
Function
Power On
Standby /
Pin
Port Name Name Detail of Function
No.
(P.C.B.)
132 AIN1 INPUT_PRT AD HiZ Protection INPUT power voltage detect +12D/+5A/+30V
PJ1/AIN1 (AD)
133 AIN2 VBUS_PRT AD HiZ Protection USB power voltage detect USB_VBUS
PJ2/AIN2 (AD)
134 AIN3 – HiZ HiZ Protection NET power voltage detect +3.3N/+1.8N/+1.2N (Spare)
PJ3/AIN3/ADTRGn
135 AIN4 HDMI_PRT AD HiZ [AD] Protection HDMI power voltage detect +5H/+3.3H/+1.2H
PJ4/AIN4/KWUP0
136 AIN5 AW_PRT AD HiZ Protection AW power voltage detect AW +5AW
PJ5/AIN5/KWUP1
137 PJ6 – HiZ HiZ ADC power down output (Spare)
PJ6/AIN6/KWUP2
T
138 PJ7 MODEL HiZ HiZ MODEL discrimination (High: YSP-CU4300, Low: YSP-CU3300)
PJ7/AIN7/KWUP3
F
139 PK0 DIR_WCK2 I I LR clock input for CDDA writing
PK0/AIN8
140 PK1 DEST_N_WR I HiZ For setting destination writing mode
PK1/AIN9 Valid only in self-diagnostic function mode
A
141 AIN10 DAMP_PRT AD HiZ Protection DAMP power voltage detect +26V
PK2/AIN10
142 AIN11 26V_PRI AD HiZ 26V current detect
R
PK3/AIN11
143 AIN12 DC_PRT HiZ HiZ Protection WF amplifier DC detect
PK4/AIN12
D
144 AIN13 DSP_PRT AD HiZ Protection power voltage detect +3.3DSP/+1.2DSP
PK5/AIN13
Key detection for A/D port
Key input (A/D) pull-up resistance 10 k-ohms
0Ω +4.3 kΩ +6.8 kΩ ∞
Detected voltage value
0 – 0.165 V 0.825 – 1.155 V 1.155 – 1.485 V 3.2 – 3.3 V
at 171 pin
A/D value
0–5 25 – 35 35 – 45 100
(3.3V = 255)
KEY1 INPUT VOLUME + VOLUME – Key off
104
YSP-CU4300/YSP-CU3300/NS-WSW160
NS-WSW160
YSP-CU4300/YSP-CU3300/
IC503: YSS952 (DSP P.C.B.)
NS-WSW160
DSP (Digital sound producer-2)
* No replacement part available. / サービス部品供給なし
GPIO0 7
GPIO1 6
GPIO2 5 SDSP
GPIO3 3
GPIO4 2
GPIO5 1 General Audio
IO Interface
switch (AIF)
T
GPIO6 32
GPIO7 30
F
GPIO8 28
GPIO9 27 MDSP2
A
GPIO10 26
GPIO11 21
D R
FM Synthesizer
IC_N 9
XIN 12
Clock PLL Registers
Generator
XOUT 13
IRQ_N 19
SCL 15 Microprocessor Interface
SDA 16
DVDD18
GPIO11
TESTb
IRQ_N
OPEN
OPEN
DVSS
DVSS
Preset ROM
24
23
22
21
20
19
18
17
DVSS 25 16 SDA
TESTb 22 GPIO10 26 15 SCL
GPIO9 27 14 IOVDD
GPIO8 28 13 XOUT
IOVDD 29 12 XIN
GPIO7 30 11 PLLVSS
DVDD18 31 10 PLLVSS
GPIO6 32 9 IC_N
1
8
GPIO5
GPIO4
GPIO3
DVSS
GPIO2
GPIO1
GPIO0
PLLVDD
105
YSP-CU4300/YSP-CU3300/NS-WSW160
Pin Function I/O
Detail of Function
YSP-CU4300/YSP-CU3300/
No. Name (*1)
1 GPIO5 Is/O General-Purpose I/O pins
NS-WSW160
2 GPIO4 Is/O These I/O pin are assigned to the digital audio pins (WCK/BCK/SDIx/SDOx)
3 GPIO3 Is/O with AIFMD[3:0] register (5V tolerant)
4 DVSS – GND
5 GPIO2 Is General-Purpose I/O pins
6 GPIO1 Is These I/O pin are assigned to the digital audio pins (WCK/BCK/SDIx/SDOx)
7 GPIO0 Is with AIFMD[3:0] register (5V tolerant)
8 PLLVDD – PLL power supply ranging from 1.65V to 1.95V (*4)
9 IC_N Is Hardware reset pin (5V tolerant)
10 PLLVSS – PLL GND (*2)
11 PLLVSS –
12 XIN I Clock input pin
Connect a 22.5792MHz or 24.576MHz crystal resonator as shown in the example below (*3, 4)
When a crystal resonator is not used, feed a clock of 22.5792MHz or 24.576MHz to XIN pin
(Change the input clock frequency only when IC_N is at “L” level)
13 XOUT O Clock output pin
Connect the external circuit as shown in the example below (*3)
When an external clock is directly fed to XIN pin without a crystal resonator, leave this pin open
Use this pin only for clock generation
T
14 IOVDD – Control interface power supply ranging from 3.0V to 3.6V
15 SCL Is I2C control bus clock input pin (not 5V tolerant)
F
16 SDA Is/Od I2C control bus data I/O pin (not 5V tolerant)
17 OPEN – Leave this pin open (*5)
18 DVSS – GND
19 IRQ_N Od Interrupt request output pin to the host controller (Interrupt request generating from DSP block)
A
20 DVDD18 – Core power supply ranging from 1.65V to 1.95V
21 GPIO11 Is/O General-Purpose I/O pins
These I/O pin are assigned to the digital audio pins (WCK/BCK/SDIx/SDOx)
R
with AIFMD[3:0] register (5V tolerant)
22 TESTb Is Test pin
Connect this pin to the GND
D
23 DVSS – GND
24 OPEN – Leave this pin open (*5)
25 DVSS – GND
26 GPIO10 Is/O General-Purpose I/O pins
27 GPIO9 Is/O These I/O pin are assigned to the digital audio pins (WCK/BCK/SDIx/SDOx)
28 GPIO8 Is/O with AIFMD[3:0] register (5V tolerant)
29 IOVDD – Control interface power supply ranging from 3.0V to 3.6V
30 GPIO7 Is/O General-Purpose I/O pins
These I/O pin are assigned to the digital audio pins (WCK/BCK/SDIx/SDOx)
with AIFMD[3:0] register (5V tolerant)
31 DVDD18 – Core power supply ranging from 1.65V to 1.95V
32 GPIO6 Is/O General-Purpose I/O pins
These I/O pin are assigned to the digital audio pins (WCK/BCK/SDIx/SDOx)
with AIFMD[3:0] register (5V tolerant)
*1 I/O symbols
I: Input pin Is: Schmitt trigger input pin O: Output pin Od: Open-drain output pin Ot: Tri-state output pin I/O: I/O pin
Is/Od: I/O pin (schmitt trigger input pin, Open-drain output pin) –: Power supply pin, GND pin
*2 PLLVDD and DVDD18 should be same voltage because they are internally connected each other.
PLLVSS and DVSS pins are also internally connected as well.
*3 XIN pin input frequency
24.576MHz clock should be fed to XIN pin if MDSP2 firmware stored in the on-chip ROM is used.
*4 The figure below shows an example of connecting a crystal resonator.
Xin Xout
22.5792MHz
24.576MHz
* Select appropriate resistor and capacitor values according to the resonator’s specification.
*5 OPEN pins must not be connected each other.
106
YSP-CU4300/YSP-CU3300/NS-WSW160
IC501: R5F21266SNFP (DSP P.C.B.) Pin Function
Port Name I/O Detail of Function
Single chip 16-bit microprocessor No. Name
* No replacement part available. / サービス部品供給なし 1 P3_5/SCL/SSCK/ MODE I Connect this pin to VCC via a resistor
(TRCIOD)
2 P3_7/TRAO/SSO/ VCC/AVCC I Apply 2.2 to 5.5 V (J, K version are 2.7 to 5.5 V) to the VCC pin
RXD1/(TXD1) Apply 0 V to the VSS pin
8 8 6 1 3 2
I Power supply for the A/D converter
Connect a capacitor between AVCC and AVSS
3 RESET XIN I These pins are provided for XIN clock generation circuit I/O
I/O ports Port P0 Port P1 Port P3 Port P4 Port P5 Connect a ceramic resonator or a crystal oscillator between the XIN and XOUT pins
To use an external clock, input it to the XIN pin and leave the XOUT pin open
T
Peripheral functions 4 XOUT/XCOUT/ VSS/AVSS I Apply 2.2 to 5.5 V (J, K version are 2.7 to 5.5 V) to the VCC pin
A/D converter System clock P4_7 Apply 0 V to the VSS pin
(10 bits x 12 channels) generation circuit
Timers I Power supply for the A/D converter
XIN-XOUT
F
High-speed on-chip oscillator Connect a capacitor between AVCC and AVSS
Timer RA (8 bits) Low-speed on-chip oscillator
Timer RB (8 bits) UART or XCIN-XCOUT(3)
5 VSS/AVSS XOUT O These pins are provided for XIN clock generation circuit I/O
Timer RC clock synchronous serial I/O
(16 bits x 1 channel) (8 bits x 2 channels)
Connect a ceramic resonator or a crystal oscillator between the XIN and XOUT pins
Timer RE (8 bits) To use an external clock, input it to the XIN pin and leave the XOUT pin open
I2C bus interface or clock synchronous
6 XIN/XCIN/P4_6 N_RESET I Input “L” on this pin resets the MCU
A
serial I/O with chip select 7 VCC/AVCC TXD1 O Transmit data output pin
(8 bits x 1 channel)
8 MODE SCL I/O Clock I/O pin
9 P4_5/INT0/(RXD1) RXD1 I Receive data input pin
LIN module 10 P1_7/TRAIO/INT1 Fschange I/O
(1 channel)
11 P3_6/(TXD1)/ CHG_I I/O
R
(RXD1)/(INT1)
Watchdog timer R8C microprocessor core Memory 12 P3_1/TRBO N_RES_AW I/O
(15 bits)
R0H R0L SB ROM(1)
13 P5_4/TRCIOD P5_4 I/O CMOS I/O ports
R1H R1L USP Each port has an I/O select direction register,
R2
ISP 14 P5_3/TRCIOC P5_3 I/O allowing each pin in the port to be directed for input or output individually
D
R3
INTB RAM(2)
A0
Any port set to input can be set to use a pull-up resistor or not by a program
PC
A1 15 P1_6/CLK0/(SSI) P1_6 I/O P1_0 to P1_7 also function as L
FB FLG
Multiplier
16 P1_5/RXD0/ RXD0 I Receive data input pin
(TRAIO)/(INT1)
NOTES:
1. ROM size varies with MCU type.
17 P1_4/TXD0 TXD0 O Transmit data output pin
2. RAM size varies with MCU type. 18 P1_3/KI3/AN11/ GSEL1 I/O
3. CXIN, XCOUT can be used only for N or D version.
(TRBO)
19 P1_2/KI2/AN10/ GSEL2 I/O
TRCIOB
20 VREF/P4_2 VREF I Reference voltage input pin to A/D converter
21 P1_1/KI1/AN9/ (KEY) I/O
7 VCC/AVCC
TRCIOA/TRCTRG
5 VSS/AVSS
3 N_RESET
22 P1_0/KI0/AN8 SEL0 I/O
8 MODE
4 XOUT
2 TXD1
1 SCL
23 P3_3/INT3/SSI/ SEL1 I/O
6 XIN
TRCCLK
24 P3_4/SDA/SCS/ SDA I/O Data I/O pin
RXD1 9 32 N_RES_952
(TRCIOC)
Fschange 10 31 N_MUTE
25 P0_7/AN0 VOL_DET I/O
CHG_I 11 30 STATUS_LED 26 P0_6/AN1 PROT I/O
R5F21266SNFP
N_RES_AW 12 29 EM_OFF 27 P0_5/AN2/CLK1 P0_5 I/O CMOS I/O ports
P5_4 13 28 P-CON
Each port has an I/O select direction register,
IC501 allowing each pin in the port to be directed for input or output individually
P5_3 14 27 P0_5
Any port set to input can be set to use a pull-up resistor or not by a program
P1_6 15 26 PROT P1_0 to P1_7 also function as L
RXD0 16 25 VOL_DET 28 P0_4/AN3/TREO P-CON I/O
TXD0 17
GSEL1 18
GSEL2 19
VREF 20
(KEY) 21
SEL0 22
SEL1 23
SDA 24
29 P0_3/AN4 EM_OFF I/O
30 P0_2/AN5 STATUS_LED I/O
31 P0_1/AN6 N_MUTE I/O
32 P0_0/AN7/(TXD1) N_RES_952 I/O
107
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 ■ BLOCK DIAGRAMS YSP-CU4300 YSP-CU3300
AUDIO Section Block Diagram
/INT,MCHNG,IPL_ERR
YSP-CU4300 DAMP
TI_WARNG
r 4FFQBHF→
DC_PRT
SEARCH,BUSY
SCHEMATIC DIAGRAM
APL_N_RST
APL_N_CS
Wireless Subwoofer
USB_N_RST
USB_N_CS
SPI_USB
I2C_USB
2 IC906
XL302 NJM2904M
14.9344MHz IC916 IC923
T
IC305
PWM Modulator
Digital Amplifier
TAS5342LDDV
L
TAS5086DBT
APPLE
MFI341S2162
IC302 DRIVER
I2C_PWM
USB USB_HOST UART_AW Airwired-2 WOOFER
BU94607ARKV-E2 PWM_N_RST
F
PWM_N_PDN R (YSP-CU4300: 75W+75W)
PWM_N_MUTE (YSP-CU3300: 50W+50W)
RX_N_EN TX_N_EN
3
D4_N_DISABLE
D4_N_WARNG
XL901 XL902
A
FM TUNER Input selector
24.576MHz 14.688MHz
D4_N_RST
D4_N_IRQ
ADC
D4_N_CS
ANALOG (L, R)
SPI_D4
INPUT ANALOG IC907
IC2 IC3 IC303, 304 TC7SHU04FU
NJM2750M
MUX
INPUT INTELLIBEAM MIC TC74VHC157FT
R
NJM2068MD IC901 IC915 IC905
r 4FFQBHF
→
SCHEMATIC DIAGRAM Digital Amplifier-1
MUX
ISEL_CNT1,2 TC74VHC541FT YDA141-SZ
COAXCIAL IC501
DIR
DSP
4
D
TV D81YK113CZKB400 IC502
INPUT SDRAM
IC301
DIGITAL 48 F1 M12L64322A-6TG2U IC909
OPTICAL DIR
PCM9211PTR XL501 Digital Amplifier-2 DRIVER
IC105 20MHz IC503 TWEETER
ARC YDA141-SZ
49 F2
Serial ROM
XL302 W25Q80BVSSIG (YSP-CU4300: 2W x 22)
TC7WHU04FU 24.576MHz
(YSP-CU3300: 2W x 16)
DIR_N_INT
DIR_N_RST
DIR_N_CS
SPI_DSP
SPI_DSP
DSP1_N_RST
DSP1_N_CS
DSP1_FMT
DSP1_N_INT
DSP1_N_RDY
OUT IC911
(ARC)
Digital Amplifier-3
5 YDA141-SZ
IC101
IN1 HDMI/OSD YSP-CU4300
HDMI SII9573CTUC
IN2 PDET
68
HDMI_N_INT IC704 124 PCON Power Supply Circuit
IN3 69,129 HDMI_N_REST Reset IC
HDMI_MUTE
R1136N271A-TR-F
SPI_FL
IN4 I2C_HDMI FL DISPLAY
Forced Reset 73, 82,84
113 114
FL_N_CS with built-in driver
IC701 FL_N_RST
IC102 3 IC702 63 FL_PON
6 XL101 OSDROM_WRITE P-GOOD Microprocessor
27MHz Serial ROM R3116N301C-TR-F 74
W25Q16CVSSIG TMPM362F10FG SDSUR_N_LED LED
r 4FFQBHF–130 → E2P_N_CS
DIGITAL IC703 76 PWR_N_LED
SCHEMATIC DIAGRAM EEPROM IC706
R1EX25032ASA00A REMOTE
SPI_E2P 88 REM_IN IR IN (Front) Remort control
IR_IN
IR IN (Rear) IR IN
IC710 UART_232C (U, C, T, B, G, F models)
232C Driver TC7SH08FU
26,123
MAX3232CPWR CTS,RTS 86 FLASHER_PON
IC6, 7, 9 IR Bar
129 IR_FLASHER IR_RPT
TC7SH04FU IR OUT
CEC
115 116 118 120
7
XL701 XL702
32.768KHz 10MHz
108
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 YSP-CU4300 YSP-CU3300
Power Supply Section Block Diagram
C23
T1
2 D1
S3
C2
C1 R1 C4 P2 S4
AC IN
T
PT NC L6 D20
F1 L2 C3 L3
L4
P1 NC
Q2 +26D
NC S2A
F
L7
NC S2B
D9 DGND
V1 S1A
V2 S1B IC11
Regulator
3 NC SI-8008TFE +12D
A
Power +12D
r 4FFQBHF
→ transformer
POWER
SCHEMATIC DIAGRAM
Q1
IC1
Control IC IC12
Regulator
FA5511N-D1-TE1
IC4 SI-8008TFE +3.3D
R
+3.3D
IC13
D
IC6
P-CON
C24
T2 L5 D16 D17 L11
NC S1
S6.3
P2
5 PT S2A
D14 L10
P1 S2B
S3.3
NC S2C
D10
V1 S3A
SGND
V2 S3B
V3 NC
Power
transformer
IC2
Control IC IC7
6
MIP2F40MSSCF
D11
IC3
POWER
Detect AC_PWR_DWN
Circuit
7
109
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 NS-WSW160
Power Amplifier Section Block Diagram
r 4FFQBHF→
DSP MAIN r 4FFQBHF→
SCHEMATIC DIAGRAM SCHEMATIC DIAGRAM
T
IC202A IC201A IC201B POWER AMPLIFIER
IC505 NJM4580E NJM4580E NJM4580E Q3-6,8,10-12,18
+5V 2
DAC - 1 3 +B
F
+ 1 5
PCM1781DBQR + + 7
3 - LIMITER - RY1
2 -
6 D4,5
3 DRIVER
A
+
XL502
-B
1MHz
12 L.P.F
R
L.P.F H.P.F
+3.3V IC503 -6dB/oct YST
-12dB/oct -12dB/oct
DSP
13
+1.8V YSS952-QZE2 R61
XL501 +B
4 20MHz
D
PROTECTION
4 6 -B
Q7,9,13,20
+3.3V IC501
Microprocessor
R5F21266SNFP
XL100 T2 F301
5
15V Q1,D6
RY302
ID Switch Power
Regulator Supply AC IN
Air Wired SW201,202
D201
LINK indicator
-15V Q2,D7 D3
+5V
+5V
6 RELAY T301
+3.3V RY302
IC506 IC504 IC303 LINE
+1.8V Regulator Regulator Regulator FILTER
Power
RP130Q181D-TR-F RP132H331D-T1-FE KIA7805PI Supply
L302
D314
110
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 NS-WSW160
Power Supply Section Block Diagram
P.C.B. MAIN (2) r 4FFQBHF→
MAIN (2)
SCHEMATIC DIAGRAM P.C.B. MAIN (1)
2 T2 MAIN (1)
Q1,2 r 4FFQBHF→
Power
T
SCHEMATIC DIAGRAM
Transformer Regulator
W5 W5 ±15
F
P-CON Q3-6,8,10-12,18
Power Amplifier
P.C.B. MAIN (3) MAIN (3) r 4FFQBHF→
3 SCHEMATIC DIAGRAM
A
IC201 IC202
R
Ope-Amp Ope-Amp
Filter Filter ±15 ±15
T301 NJM4580E NJM4580E W203 CB23
Sub-
4
Transformer
D
IC303 D201
Regulator Status LED
KIA7805PI +5V +5V
P.C.B. DSP (1)
+5V CB304 W204
Q1 IC505
FET Switch DAC
5V 5V RZR020P01TL PCM1781DBQR
W206 CB503
5
IC504 IC506
Regulator Regulator
RP132H331D-T1-F RP130Q181D
+3.3V +1.8V
P.C.B. AWCD2A P.C.B. DSP (2)
IC503
DSP (2) DSP
r 4FFQBHF→ YSS952-QZE2
SCHEMATIC DIAGRAM
6
IC508 IC501
Regulator Microprocessor
+5V +5V +5V +5V RP132H331D-T1-F R5F21266SNFP
CB101 CB601 CB602 CB501 M3.3V
DSP (1) r 4FFQBHF→
SCHEMATIC DIAGRAM
111
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 ■ PRINTED CIRCUIT BOARDS YSP-CU4300 YSP-CU3300
DIGITAL (Side A)
POWER (1)
2 (CB6)
AC_PDN_DET
INPUT (1)
P_CON
T
(CB4) INPUT
DGND
DGND
DGND
DGND
AGND
+3.3D
+3.3D
+12D
HDMI
AUR
AUL
+5D
+5A
PRI
DIGITAL
OUT
OPTICAL TV (RESET) RS-232C IN4 IN3 IN2 IN1
(ARC)
W301
F
W303
CB102 CB104 CB105
CB704 CB101 CB103
AW_WCK
AW_SD0
DGND AW_BCK
DGND
AW_MCK
3 DGND TI_WARNG
A
PWM_N_RST 48 37
PWM_N_PDN 1 36
DAMP_PRT
CB504
DGND 8 1
IC301
PWM_SCL
PWM_SDA 1 8
DC_PRT 12
IC507
25
PWM_N_MUTE 13 24
IC303
AW_FS_I 4 5
AW_MOSI 9 16
DGND
AW_MISO 3
AW_FS_N_O 4
IC103
R
RX_N_EN 5 1
TX_N_EN IC101
5 4
DAMP IC707
144 109
(CB902) 1 108
1 3
44 43
REMOTE
IC701
4
D
DGND
IR_FLASHER 10 1
D4_N_IRQ DGND 5 4
IC703
D4_PON
D4_N_DISABLE IC504
D4_N_RST IC502
8 1 4 3
D4_MISO IC106
D4_MOSI 10 6 36 73 5 1
D4_N_CS
CB503
IC305 37 72
D4_SCK 11 20
IC501 11 5 5
D4_N_WARNG
IC104
DGND 15
DIR_MCK
DGND 16 20
1 No replacement part available.
86 1 1
DSP_BCK サービス部品供給なし
DGND
DSP_S
DSP_C 80 61
DSP_F
DSP_WF 5 4
60
DSP_WCK 1
IC503
IC302
IC106
8 1
DAMP
(CB901) 20
40
41
21 IC302
5 IC703
YSP-CU4300
DGND
USB_DP
USB_DM
USB_FLG
VBUS_PRT
S3.3
S3.3
DGND
DGND
DGND
S6.3
AW_PON
AW_PRT
KEY1
DGND
S3.3
STBY_SW
No replacement part available.
サービス部品供給なし YSP-CU4300
TUN_USB_SDA
SDSUR_N_LED
TUNER_GPIO
IR_FLASHER
PWR_N_LED
USB_N_PON
HDSUR_LED
MIC_N_DET
INPUT_PRT
ISEL_CNT2
DIG_COAX
FL_N_RST
INPUT (2) (CB52)
FL_MOSI
(YSP-CU4300)
POWER (1)
IR_IN
(W2) POWER (3)
(W951)
• Semiconductor Location
Ref no. Location Ref no. Location Ref no. Location
6 D101 F3 D113 I3 IC503 D5
DGND
TUN_N_RST
TUN_USB_SCL
DGND
FLASHER_PON
S3.3_2_PON1
FL_N_CS
SW_N_MUTE
ISEL_CNT1
DGND
DGND
DGND
FL_PON
D115 I3 IC504 C4
FL_SCK
D102 F3
D103 F3 IC101 H4 IC507 C3
D104 G3 IC103 I3 IC701 F4
D105 G3 IC104 I4 IC703 G4
D106 G3 IC106 H4 IC707 G4 INPUT (1)
D107 H3 IC301 D3 Q109 H5 (CB8)
D108 H3 IC302 E5 Q110 H5
D109 H3 IC303 E3 Q301 C3
D110 H3 IC305 E4 Q302 C3
D111 H3 IC501 C4 Q703 G4
7
D112 H3 IC502 D4
112
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 YSP-CU4300 YSP-CU3300
DIGITAL (Side B)
3 1
F T
IC105
A
8
5
4
16 9
IC304
1 16
IC710
R
8 9
4 1
IC708 1 8
5 8
IC704
1 5
3 4
D
5 4
IC102
8 1
5 4
IC702
5 4
IC706
1 3
1 3
YSP-CU4300 YSP-CU3300
• Semiconductor Location
Ref no. Location Ref no. Location
D114 E3 Q103 D3
D116 B3 Q104 D3
IC102 C4 Q105 D3
6 IC105 B3 Q106 C3
IC304 F3 Q107 C3
IC702 E4 Q108 C3
IC704 E4 Q111 D4
IC706 D4 Q701 D4
IC708 D4 Q702 D4
IC710 E3 Q704 D4
Q101 E3 Q705 D4
Q102 E3
113
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 YSP-CU4300 YSP-CU3300
INPUT (1) (Side A) INPUT (2) (Side A) INPUT (3) (Side A)
YSP-CU4300
U, C, T, B, G, F models
AUX INPUT INTELLIBEAM DAMP
IR OUT IR IN (CB915)
INPUT DIGITAL ANALOG MIC
IR_FLASHER
L R DIGITAL POWER (1)
REMOTE
(CB302) (CB4)
2
DGND
DGND
DGND
DGND
S3.3
1
DGND
IC52
USB_DP CB73 CB72
FM TUNER USB_DM
CB52
5
(YSP-CU4300) USB_FLG
TUN_USB_SCL
JK3 JK2 JK1
TUN_N_RST
VBUS_PRT 4 1
IC51 5 4
F
DGND
Rch OUT
Lch OUT
IC72
5 8
DGND
1 3
VBUS 4
-
5
IC71
VBUS
TUN_USB_SDA
4
IC1
5 1 3
8 1 16 9
3
IC7
5 4
IC3
IC2
A
5 4 CB51
GPIO
GND
3 8 1
+5A
1
1 8 Remote control TV remote control
sensor sensor
USB
3 1
R
CB1
IC9
CB4
IC4
4 5
3 1
3
IC6
4 1
4 5
IC5
4 5
D
8
INPUT (4) (Side A)
CB3 CB9
CB6
DAMP
YSP-CU4300 (CB916)
AW_FS_N_O
AW_RX_EN
POWER (1)
AW_TX_EN
AW_MOSI
AW_MISO
AW_FS_I
Remote control (CB7)
S3.3AW
LRCLK
DGND
DGND
DGND
DGND
DGND
DGND
DGND
+5AW
+3.3D
MCLK
SDTO
BCLK
sensor
SDTI
CB7
CB5 1 20 W63
CB8
IC61
CB65
DGND
DGND
VBUS
VBUS
IR_OUT
DGND
IR_OUT
DGND
10 11
5 U, C, T, B, G, F models
+5A
SDSUR_N_LED
TUN_USB_SDA
SDSUR_N_LED
TUNER_GPIO
AUR
IR_FLASHER
PWR_N_LED
PWR_N_LED
USB_N_PON
HDSUR_LED
MIC_N_DET
INPUT_PRT
AGND
ISEL_CNT2
DIG_COAX
FL_N_RST
FL_N_RST
FL_N_CS
FL_MOSI
FL_MOSI
AUL
FL_SCK
POWER (4) POWER (5) DGND
FL_F1
FL_F2
+3.3D
IR_IN
+30V
(W971) (W981) +5D +26D
DGND
+3.3D
DIGITAL DGND
(W301) DGND
S3.3 CB61
DGND
TUN_N_RST
TUN_USB_SCL
DGND
FLASHER_PON
S3.3_2_PON1
FL_N_CS
SW_N_MUTE
ISEL_CNT1
DGND
DGND
DGND
FL_PON
FL_SCK
+12D
FL_F1
FL_F2
+30V
DGND
DGND
DGND
DGND
DGND
DGND
HDSUR_LED
POWER (1)
6 (W5)
CHANGE_FS_N_O
DIGITAL POWER (2)
RESET_N
(CB702)
(CB901)
LRCLK
DGND
DGND
DGND
DGND
DGND
DGND
• Semiconductor Location
Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location
D1002 B5 D1011 D5 IC5 F4 IC61 I5 Q1004 C4 Q1022 B4
UART_TX
UART_RX
CHANGE_FS_I
SDTI
MCLK
BCLK
SDTO
D-
D+
P5V
D1003 B3 D1012 D5 IC6 B4 IC71 J3 Q1007 B3 Q1023 A3
D1004 B3 IC1 C3 IC7 B3 IC72 I3 Q1009 A3 Q1024 A3
D1005 B3 IC2 E3 IC9 A4 Q1001 B4 Q1010 B3 Q1027 E4
7 D1009 F4 IC3 D3 IC51 H3 Q1002 B4 Q1014 F4 Q1029 D4 AWCD2A P.C.B.
D1010 D5 IC4 E4 IC52 H2 Q1003 C4 Q1021 B4 Q1032 E4
114
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 YSP-CU4300 YSP-CU3300
INPUT (1) (Side B) INPUT (2) (Side B) INPUT (3) (Side B)
YSP-CU4300
T
U, C, T, B, G, F models
F
3
A
YSP-CU4300
R
4
D
INPUT (4) (Side B)
11 10
IC63
20 1
K, A, L, V, S, H, J models U, C, T, B, G, F models
5
• Semiconductor Location
Ref no. Location Ref no. Location
D1001 C3 Q1018 D4
D1006 E3 Q1019 C4
D1008 C4 Q1020 C4
IC63 H5 Q1025 E3
6 Q1011 E3 Q1028 B4
Q1013 E3 Q1030 C4
Q1015 C4 Q1031 B5
Q1016 C4 Q1033 C4
Q1017 D4
115
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 YSP-CU4300 YSP-CU3300
• Semiconductor Location
Ref no. Location Ref no. Location Ref no. Location
DAMP (Side A) D1601 I5 IC902 I5 IC913 E4
WF_R-
– D1602 F5 IC903 I3 IC915 G4
L POWRE (1)
(W1) D1603 F5 IC905 H5 IC916 H3
MGND
MGND
+
+12D
+26D
+26D
WF_R+ D1604 F5 IC906 D3 IC917 H4
DRIVER D1605 F5 IC907 H4 IC923 G3
WOOFER D1606 C3 IC909 D5 Q1602 F5
–
2 WF_R- D1607 C3 IC911 C5 Q1603 F5
POWER (1) (W3) + R
WF_R+ IC901 I5 IC912 B4 Q1604 F5
(YSP-CU4300)
MGND
T
Q1605 F5
+26D
YSP-CU4300 YSP-CU3300 YSP-CU4300
Q1607 C3
Q1608 C3
F
CB906
4 23 22
5
IC906
AW_WCK
AW_SD0
IC923
CB913 8 DGND
1 AW_BCK
3 DGND
AW_MCK
A
INPUT (4) 38 20 DGND
TI_WARNG
CB902
48 1 PWM_N_RST
(CB65) IC916 20 11
CB908
PWM_N_PDN
DAMP_PRT
1 19 IC903 DGND
PWM_SCL
AW_MOSI PWM_SDA
DGND CB910 DC_PRT
PWM_N_MUTE
R
AW_MISO AW_FS_I
AW_FS_N_O 1 10 AW_MOSI
DGND
AW_FS_I AW_MISO
AW_FS_N_O
AW_TX_EN AW_RX_EN
AW_RX_EN AW_TX_EN
DGND
IC916
11 10 10
MCLK 11
IC912
DIGITAL
IC915
DGND
4 (CB504)
D
BCLK 20 1 20 1
DGND
IC913
LRCLK 3 1 5 4
SDTO 4 5 3 5 4
1 1 3
DGND IC917IC907
REMOTE
SDTI DGND
50 26 26 50 26 IR_FLASHER
25 25 25 DGND
51 51 50 51 D4_N_IRQ
D4_PON
3 1 20 11 D4_N_DISABLE
D4_N_RST
IC911
IC909
CB901
IC905
IC901 D4_MISO
DGND IC902 D4_MOSI
4 6 D4_N_CS
IC915
IR_FLASHER D4_SCK
DGND D4_N_WARNG
75 1 75 1 75 1 DGND
REMOTE 76 100 76 100 76 100 DIR_MCK
DGND
1 10 DSP_BCK
5 DGND
DSP_S
INPUT (3) DSP_C
(CB73) CB904 DSP_F
CB912 CB905
DSP_WF
CB909 DSP_WCK
CB911 CB907
DIGITAL
(CB503)
C_P1
C_M1
C_P2
C_M2
C_P3
C_M3
C_M4
C_P4
C_M5
C_P5
C_M6
C_P6
N.C.
B_P0
B_M0
B_P1
B_M1
B_P2
B_M2
B_P3
B_M3
B_M4
B_P4
B_M5
B_P5
B_M6
B_P6
B_M7
B_P7
N.C.
N.C.
A_P0
A_M0
A_P1
A_M1
A_P2
A_M2
A_P3
A_M3
A_M4
A_P4
A_M5
A_P5
A_M6
A_P6
A_M7
A_P7
6
+ – – + + – – + + – – +
TWEETER x 3 TWEETER x 3 TWEETER x 4 TWEETER x 4 TWEETER x 4 TWEETER x 4
DRIVERS
Note: 注意：
Precaution for handling measuring instrument 計測機器取り扱い上の注意
7 Since the speaker output of this unit is BTL connected, the ground side of the 本機のスピーカー出力は BTL 接続となっていますので、スピーカー端子に接続
measuring instrument to be connected to the speaker terminal MUST be kept in する計測器のアース側はフローティング状態に保つ必要があります。
floating condition.
116
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 YSP-CU4300 YSP-CU3300
DAMP (Side B)
T
YSP-CU4300
F
15 1
IC920
5 4 IC910
5 4
16 30
IC921
3 1 3
A
1 3
R
4
6
D 30
1
IC908
16
15
YSP-CU4300
• Semiconductor Location
Ref no. Location
IC908 E5
IC910 H3
IC920 B3
IC921 C3
Q1601 E5
Q1606 H3
Q1609 E5
7 Q1610 H3
117
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 YSP-CU4300 YSP-CU3300
AW_RPT
AW_PON
POWER (1) (Side A) S6.3
SGND DIGITAL
SGND (CB106)
SGND
S3.3
S3.3
INPUT (3)
(CB72) INPUT (4)
2 (W63)
5 k-ohms
S3.3AW
SGND
SGND
SGND
SGND
+5AW
+3.3D
T
U, C, V, S, J models 10 W
S3.3
YSP-CU4300
CB4
F
CB7
+26D
DGND
W2
DAMP (CB913)
(YSP-CU4300)
3 W3
A
IC6
IC3
IC4
IC7
CB3
DIGITAL (W303)
P_CON
AC_PWR_DWN
R
CB1
26V_PRI
CB2
+3.3D
W1
+3.3D
CB6
IC2
DGND
DGND
AC IN DGND
+12D
D
+12D
S3.3
DGND
W5
DGND
+3.3D
DGND
+26D
IC12 IC11
INPUT (1)
(CB6)
5 1 5 1
T, K, A, B, G, F, L, H models U, C, V, S, J models
U, C, V, S, J models T, K, A, B, G, F, L, H models
+26D
5 k-ohms
+26D
10 W DAMP DGND
(CB910)
DGND
6 +12D
• Semiconductor Location
Ref no. Location Ref no. Location
D1 C4 IC2 E4
D3 E4 IC3 D3
Notes) 注意） D4 E4 IC4 F3
Safety measures 安全対策
• Some internal parts in this product contain high voltages and are dangerous. Be sure to take safety measures during servicing, such
D7 F4 IC6 F3
・ この製品の内部には高電圧部分があり危険です。修理の際は、絶縁性の手袋を使用するなどの安全対策を行ってください。
as wearing insulating gloves. ・ 下記のコンデンサには電源を OFF にした後も電荷が残り、高電圧が維持されており危険です。修理作業前に放電用抵抗（5 D8 F5 IC7 D3
• Note that the capacitors indicated below are dangerous even after the power is turned off because an electric charge remains and a k Ω /10 W）を下記の各コンデンサの端子間に接続して放電してください。放電所用時間は各々約 30 秒間です。 D9 F4 IC11 H5
7 high voltage continues to exist there. Before starting any repair work, connect a discharging resistor (5 k-ohms/10 W) to the terminals POWER（1）P.C.B. の C8、C44、C48
of each capacitor indicated below to discharge electricity. The time required for discharging is about 30 seconds per each. D14 E3 IC12 H5
C8, C44 and C48 on POWER (1) P.C.B. D20 G4 Q2 E4
118
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 YSP-CU4300 YSP-CU3300
POWER (1) (Side B)
F T
IC5
1 5
5 4
KRA
3
IC8
1 3
• Semiconductor Location
A
IC9
Ref no. Location
D2 D3
D5 E4
D6 E4
R
D10 D3
4 1 D11 C3
D12 D3
IC1
D15 H3
5 8
D16 E3
4
D
D17 E3
D22 H5
D23 D3
D24 G5
D28 D3
IC1 E4
IC5 H3
IC8 D3
IC9 F3
Q1 E4
Q3 D3
5
Q4 G2
Q5 F3
Q6 H4
Q7 H4
T, K, A, B, G, F, L, H models Q8 G8
U, C, T, K, A, B, G, F, L, V, S, H models
119
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 YSP-CU4300 YSP-CU3300
POWER (2) (Side A) POWER (3) (Side A)
(On/Standby) + VOLUME - INPUT
2
T
STATUS
indicator
F
SURROUND
indicator
KEY1
DGND
S3.3
STBY_SW
• Semiconductor Location
3
Ref no. Location
HDSUR_LED
DGND
DGND
DGND
DGND
DGND
DGND
+30V
FL_F2
FL_F1
A
D901 B3
D902 B2 DIGITAL
(CB703)
D971 B5
D981 D5
SDSUR_N_LED
PWR_N_LED
FL_MOSI
FL_N_CS
FL_N_RST
+3.3D
+30V
FL_F2
FL_F1
FL_SCK
R
INPUT (1)
(CB7)
4
D
POWER (4) (Side A) POWER (5) (Side A) POWER (6) (Side A) POWER (7) (Side A)
5
DGND
IR_OUT
DGND
IR_OUT
6 INPUT (1) INPUT (1)
(CB3) (CB9)
120
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 YSP-CU4300 YSP-CU3300
POWER (2) (Side B) POWER (3) (Side B)
F T
W951
CB901 • Semiconductor Location
3 Ref no. Location
A
Q901 C2
R
4
D
POWER (4) (Side B) POWER (5) (Side B) POWER (6) (Side B) POWER (7) (Side B)
W971 W981
121
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 NS-WSW160
DSP (1) (Side A) DSP (2) (Side A)
2 MAIN (3) AWCD2A P.C.B.
UART_RX
(W206)
UART_TX
STATUS_LED
GPIO0
MCLK
SDTO
BCLK
MAIN (3)
SDTI
P5V
D+
(W201)
GSEL2
GSEL1
P-CON
D-
MODE
DGND
DGND
DGND
AGND
PROT
SEL1
SEL0
3.3V
RST
+5V
SIG
RESET_N
RX
TX
LRCLK
GPIO1
DGND
DGND
DGND
DGND
DGND
DGND
F
CB503 CB502
CB601
3 (For factory)
A
4 3 4 3
IC508
IC504
5 1 5 1
CB504 CB602
DGND
Fschange
RESET_N
DGND
DGND
DGND
IC502
R
5 4
IC506 1 3
2 1 No replacement part available.
UART_TX
UART_RX
CHG_I
SDTI
+5V
BCLK
LRCLK
3 4
サービス部品供給なし
32 25
1 24
IC501
4
D
16 9
8 17
IC505 9 16
24 17
25 IC503
1 8 16
32 9
1 8
CB501
5 • Semiconductor Location
Ref no. Location
IC501 D4
IC502 D4
IC503 C4
IC504 C3
IC505 C4
IC506 C4
IC508 D3
6
DGND
Fschange
RESET_N
DGND
DGND
DGND
UART_TX
UART_RX
CHG_I
SDTI
+5V
BCLK
LRCLK
122
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 NS-WSW160
DSP (1) (Side B) DSP (2) (Side B)
F T
4
R A
D
3 1
IC507
4 5
• Semiconductor Location
Ref no. Location
5 D501 C3
D503 D4
D504 C4
D505 C4
D506 C3
IC507 C4
Q501 C3
Q502 C3
Q503 C4
Q504 D4
Q507 D3
6
Q509 B5
Q510 C5
123
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 NS-WSW160
Safety measures 安全対策
• Some internal parts in this product contain high voltages and are dangerous. Be sure to take safety measures during servicing, such ・ この製品の内部には高電圧部分があり危険です。修理の際は、絶縁性の手袋を使用するなどの安全対策を行ってください。
as wearing insulating gloves. ・ 下記のコンデンサには電源を OFF にした後も電荷が残り、高電圧が維持されており危険です。修理作業前に放電用抵抗
• Note that the capacitors indicated below are dangerous even after the power is turned off because an electric charge remains and a （5 k Ω /10 W）を下記の各コンデンサの端子間に接続して放電してください。放電所用時間は各々約 30 秒間です。
high voltage continues to exist there. Before starting any repair work, connect a discharging resistor (5 k-ohms/10 W) to the terminals MAIN（1）P.C.B. の C23、C24
of each capacitor indicated below to discharge electricity. The time required for discharging is about 30 seconds per each.
C23 and C24 on MAIN (1) P.C.B. AC IN
MAIN (1) (Side A) MAIN (2) (Side A)
2 5 k-ohms
10 W
T
+5V
CB304
P-CON
DGND
W9A
CB308
CB301
CB307
W5B3 CB302
A
W5B2
IC3
+ W2A W2B
W5B1
RE
W8A
DRIVER
SUBWOOFER WH
R
-
IC303
OUT COM IN
CB23
D
Sub-transformer
AGND
MAIN
+15
-15
DGND
PROT
5 k-ohms
10 W
MAIN (3) (Side A) Group ID switch MAIN (4) (Side A)
(Reset) A–C 1–3
5 (For factory)
(Writing port) Power
CB206
transformer
CB205
RE
W5A1
LINK • Semiconductor Location WH
W9B
indicator
Ref no. Location
D3 F3
DSP (1) D201 E5 BL
W5A2
W204
(CB502)
D314 H4
W206
6 RX MAIN
IC303 G4
W203
TX AGND Q1 D4
W201
MODE +15
3.3V -15 Q2 D4
RST DGND
W5A3
+5V PROT Q14 E3 RE BE
W8B
DGND
Q15 D3
Q18A D2
DGND
Q18C E2
P-CON Q326 H3
STATUS_LED
SEL0
DGND
P-CON
+5V
DSP (1) SEL1
GSEL1
(CB503) GSEL2
DGND
7 PROT
AGND
SIG
124
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 NS-WSW160
MAIN (1) (Side B) MAIN (2) (Side B)
2
F T
4
R A
5
MAIN (3) (Side B)
5 4 5
D 4
MAIN (4) (Side B) • Semiconductor Location
Ref no. Location Ref no. Location
D2
D4
D5
D6
D7
D8
D9
D10
D11
D12
E4
B4
B4
D4
D4
C4
D3
D3
B3
B2
Q5
Q6
Q7
Q8
Q9
Q10
Q11
Q12
Q13
Q16
C4
D3
B3
C3
B3
C3
D3
C3
B3
D3
IC201
IC202
8 1
D13 B2 Q17 C3
6 8 1
D14 B3 Q20 B3
D315 G3 Q21 C2
D316 G3 Q22 C2
D317 G3 Q25 B3
IC201 D6 Q223 D6
T, K, B, G, F models IC202 C6 Q324 G2
Q3 C3 Q325 G3
Q4 C4
125
A B C D E F G H I J
YSP-CU4300/YSP-CU3300/NS-WSW160
1 ■ PIN CONNECTION DIAGRAMS
• ICs • ICs
AL1055 BD9329AEFJ-E2 BU94607ARKV-E2 D81YK113BZKB400 FA5511N-D1-TE1 TMPM362F10FG W25Q16CVSSIG YDA141-SZ YSS952-QZE2
60 41 108 73 W25Q80BVSSIG 75 51
109 72
61 76 50
40
T 24 17
15 25 16
1 16
30 T 16 4
8 8 4 32 9
2 8 4 1 1
100 26 8 9
1 8
1 A 1
1 80 21 144 37
A 1 25
T
1 16 1 36
1 20
KIA78M05F KIA7805PI M12L64322A-6TG2U MAX3232CPWR MFI341S2162 MIC37302WU TR • Diodes
86 44 15 11
F
1SS355VMTE-17 D1FK60-5063 D1NL20U-5083 DAN222 DAP222 KDS160-RTK
16 10
CMS15 (TE12L,K,M) D1FL20U-5063
8 Anode Anode
1: INPUT 16 Anode Cathode 1 2
20 6 Anode 1 2
2: COMMON Anode
1 3: OUTPUT 1
3 IN 1 5 1 Anode
OUT Cathode
3 COM 5 Anode
3
Cathode 3
A
1 43 Cathode Cathode
Cathode Cathode
MIP2F40MSSCF NJM2068MD-TE2 NJM2750M-TE2 NJM2820F TE1 NJM2886DL3-05 (TE1) NJM2904M (TE3) HZU27B TRF-E P6KE200A RB420DT146 RB050L-40 RB050LA-40TR TP
NJM2867F3-05 (TE1) HZU5.1B2 TRF-E RB160L-40 TE25 RB500V-40
HZU5.1B3 TRF-E Anode
Anode Anode RB501V-40 Anode
3 HZU12B2 TRF-E RB551V-30
R
4 K
8 4 8 1: CONTROL HZU15B3 TRF-E RR264M-400TR
5
16 3 2: VIN HZU3.0B1 TRF-E
8 4 1 3: GND 8 4 OPEN
1 1 HZU6.2B3 TRF-E
1 4: Vo 1 Cathode Cathode A Cathode Cathode
1
5 5: N.C.
RS1505M-B-C-J82 S1NB60 1.0A 600V S1ZB60-7062 SG5S9M STTH108A STTH3003CW TS4B03G C2
NJM4580E NJM431U PCM1781DBQR PCM9211PTR R1EX25032ASA00A R5F21266SNFP RS605M-B-C-J81 STTH110A
4
D
36 25
24 17
37 24
Anode
1 25 16
2
3
8 8 4 4
8 4 AC –
16 1 – AC 2 A1 AC
1 1: REFERENCE – Cathode K AC
32 9 AC + 1 1 A2
23 +
2: ANODE 1
48 13 + AC
3: CATHODE 1 8
1 12
R3116N271A-TR-F RP108J131D-T1-FE RP130Q181D-TR-F RP132H331D-T1-FE RP132S331B-E2-FE SI-8008TFE • Transistors
R3112N421A-TR-F
R3116N301C-TR-FE
2N5401S-RTK 2SA1036K 2SA1162-Y (TE85R, F) 2SA1312-GR,BL 2SA949 2SC2412K 2SC3906K 2SK2158-T1B
5 1 2SC4081 T106 2SA1037K 2SC2712-Y (TE85R, F) 2SC2229 2SD2704 K
3
4 4
5 2 3 6
3 1 5 3
1 C C C
1 1 C C C D
1 5 4
5
E E E
E E E S
SII9573CTUC TAS5086DBT TAS5342LDDV TC74LVX244FT TC74VHC157FT B B B B B B G
TC74VHC541FT E
132 89 C
B
133 88
2SK3523-01R CPH3205 DTA014EUBTL DTC023JUBTL DTC114EKA FDN360P KRA302-RTK/P KTA1046-Y-U/PFY
38 20 2SK3876-01R DTC014EUBTL DTC123JKA KRC402-RTK/P KTC2026
DTC044EUBTL DTC144EKA KRC404-RTK/P
22
6 10 8
16 3
20 C 3 3 D OUT
44 1 2 1
1 E 2 S
COMMON
1 1 2 1: GND
1 19 B 1: IN G IN
176 45 1 1: IN 2: IN
2: GND 2: GND BC
GD 3: OUT 3: OUT E
1 44 S 3: OUT
TC74VHC244FT TC7SH04FU-TE85L TC7WHU04FK TC7WHU04FU TPS2557DRBR TPS54331DR KTC3875S RSR025N03 RSR025P03TL RTR020P02TL RUR020N02TL RZR020P01TL STD01P STD01N TPCA8052-H
TC7SHU04FU TC7W14FK (TE12L,Q)
TC7SH08FU 8
TC7SH125FU 5 8 5 5
C D D D D
10 D
4 8
E S
7 5 8 4 8
4 1
8 4 S S S S 4
20 3 B G G
1 G G G 1 1 1
1 1 4 23 23
1 1 1 4 45 45
126
A B C D E F G H I J K L M N
YSP-CU4300/YSP-CU3300/NS-WSW160
SCHEMATIC DIAGRAMS YSP-CU4300 YSP-CU3300
DIGITAL 1/4
1
HDMI
OUT
IN4 IN3 IN2 IN1
(ARC)
HDMI IN-4 HDMI IN-3 HDMI IN-2 HDMI IN-1 HDMI OUT
CB101 DC1RS19JAXR190 CB102 DC1RS19JAXR190 CB103 DC1RS19JAXR190 CB104 DC1RS19JAXR190 CB105 DC1RS19JAXR190
FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
FG FG FG FG
DGND DGND
FG
SCL
SCL
SDA
GND
HPD
SCL
SDA
GND
HPD
SCL
SDA
GND
HPD
SCL
SDA
GND
HPD
CEC
SDA
GND
HPD
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Sheild2
Sheild1
Sheild0
SheildC
Utility
CEC
CEC
CEC
CEC
DGND DGND DGND
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Sheild2
Sheild1
Sheild0
SheildC
Sheild2
Sheild1
Sheild0
SheildC
Sheild2
Sheild1
Sheild0
SheildC
Sheild2
Sheild1
Sheild0
SheildC
Reserved
+5VPower
Reserved
+5VPower
Reserved
+5VPower
Reserved
+5VPower
+5VPower
DGND DGND
C157
+5V
DGND DGND DGND DGND 1/16
no_use
2
R181
R176
56
L117
C160 BLM21PG600SN1D
TP148
R178 TP150
DGND
4.7 no_use R191
R177
no_use
R182
56
5.6K 8
V+
C158 C165 R189 3 5 6 2 R200
ARC
680 33
22P(CH)
no_use
0.1/16
1/16 0.1/16(F)
C164
R183
C174
R192 4
V- to DIGITAL 2/4
18K
TP140
TP142
TP144
1 7
4
3
4
3
4
3
4
3
DGND
EXC24CH900U
EXC24CH900U
EXC24CH900U
EXC24CH900U
ZA51980
IC105
TC7WHU04FU
L110
L111
L112
L113
R101 R105 R112 R116 R124 R128 R141 R147
100K 1K 100K 1K 100K 1K 100K 1K
1
2
1
2
1
2
1
2
TP103
TP108
TP112
TP130
DGND
DGND
DGND
DGND
1
2
no_use
no_use
no_use
no_use
D103 D106 D109 D112
Q101
J101
Q103
J102
Q105
J103
Q107
J104
3
3
2SC4081
2SC4081
2SC4081
2SC4081
R102
R113
R125
R143
D101 D104 D107 D110
1K
1K
1K
1K
TP101 R106 TP106 R117
TP113
R129
TP128
R148
D102 D105 D108 D111
AVRL161A1R1NTB
AVRL161A1R1NTB
10K 10K 10K 10K
DGND
DGND
DGND
DGND
D113
D115
1
2
T
Q102
Q104
Q106
Q108
2SC4081
2SC4081
2SC4081
2SC4081
10K 3
10K 3
10K 3
10K 3
AVRL161A1R1NTB AVRL161A1R1NTB AVRL161A1R1NTB AVRL161A1R1NTB
R103
R114
R126
R144
3
TP102 R110 TP107 R121 TP114 R136 TP129 R161
L114
47K 47K 47K 47K BLM21PG600SN1D
TP104 R111 TP109 R122 TP115 R137 TP131 R162
S6.3
47K 47K 47K 47K
TP105 TP110 TP116 TP132
BLM21PG600SN1D
R127
R130
R131
R146
R149
R150
+5V
R104
R107
R108
R115
R118
R119
L115
22
10
22
22
10
22
22
10
22
10
22
22
R153
R109
R120
R132
5.1K
C101
1/16
5.1K
C102
1/16
5.1K
C123
1/16
5.1K
C131
1/16
TP147
R165
R171
R174
5VPWR_4
5VPWR_3
5VPWR_1
5VPWR_2
F
DSCL_4
DSDA_4
DSCL_3
DSDA_3
DSCL_2
DSDA_2
DSCL_1
DSDA_1
22
22
47
0.1/16(F)
HPD_2
HPD_1
HPD_4
HPD_3
C163
IC103
DGND NJM2867F3-05(TE
DGND DGND DGND CONTRPL VIN
5
GND
R179
2
47K
NC VOUT
4
TP145 D116 5.0
TP149
no_use
10/10
RB501V-40
C161
C162
R167
R173
1.8K
1.8K
4 TP141 TP143
DGND
TP146
no_use
A
R175
C159
47K
DSCL_TX0
DSDA_TX0
DGND
+3.3H1 +3.3H1
1000P(B)
1000P(B)
1000P(B)
0.1/16(F)
0.1/16(F)
0.1/16(F)
C177
C178
C137
C138
C140
C142
C146
10/10
+1.2H1 TP111 +1.2H1
C120
C121
1000P(B)
C122
1000P(B)
1000P(B)
R
0.1/16(F)
0.1/16(F)
0.1/16(F)
C111
C114
C116
C118
10/10
DGND
5 DGND
AVDD33
CVCC12
AVDD12
AVDD33
AVDD12
R3X1+
R3X1-
R3X0+
R3X0-
R3XC+
R3XC-
R2X2+
R2X2-
R2X1+
R2X1-
R2X0+
R2X0-
R2XC+
R2XC-
R1X2+
R1X2-
R1X1+
R1X1-
R1X0+
R1X0-
R1XC+
R1XC-
R0X2+
R0X2-
R0X1+
T0X1-
R0X0+
R0X0-
R0XC+
10 R0XC-
9 HSYNC
8 VSYNC
6 D19
5 D18
4 D17
3 D16
2 D15
1 D14
7 DE
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
R3X2- D13
45 176 +3.3H1 S6.3
R3X2+ D12
46 175
R4XC- D11
47 174 L116
R4XC+ IOVCC33 +3.3H1 BLM21PG600SN1D
48 +3.3H D114 BLM21PG600SN1D
173 R168
L107
R4X0- IDCK S3.3
C139
C141
1000P(B)
1000P(B)
0.1/16(F)
0.1/16(F)
49 172 27K
C143
C147
C150
10/10
RB500V-40
R4X0+ D10
50 171
R4X1- D9 IC106
51 170 NJM2867F3-05(TE
0.1/16(F)
C173
R4X1+ D8 CONTRPL VIN +5H
52 169 CEC
5
DGND HDMI_PON2
D
R4X2- D7 TP152 GND
53 168
2
TP159 5.0
R4X2+ D6 NC VOUT
54 167
4
no_use
AVDD12 D5
R188
55 166
0.1/16(F)
C171
10/10
C172
AVDD33 D4
56 165
R5XC- D3
57 164 TP156
+3.3H1
R5XC+
R5X0-
58
59
HDMI/OSD 163
162
D2
D1
DGND
R5X0+ D0
6 R5X1-
60
61 G
161
160
CVCC12
R5X1+ TOX2+
62 159
R201
R202
R203
2.7K
2.7K
10K
R5X2- TOX2-
63 158
R5X2+ DGND TOX1+ S3.3 +1.2H
64 157
RESISTOR CVCC12 TOX1-
65 156 1.3
REMARKS PARTS NAME S3.3
HDMI_SCL CSCL
66
IC101 155
TOX0+ IC104
TP170
NO MARK CARBON FILM RESISTOR (P=5) NOTICE (model) HDMI_SDA CSDA TOX0-
RP108J131D-T1-F
R184
R185
R186
1P3.3
1P3.3
1P3.3
67 154
R205 G
CARBON FILM RESISTOR (P=10) J JAPAN G 3 HDMI_N_INT INT TOXC+
no_use
SII9573CTUC
R196
R199
68 153
1 2 3 4 5
0
100 R133
METAL OXIDE FILM RESISTOR U U.S.A 2 1 RESET#
69 152
TOXC-
CE
VDD
GND
VFB
VOUT
D S R123 100
METAL FILM RESISTOR C CANADA DGND TPWR_C12CA
70 151
TDVDD12 TP169
Q111
2SK2158-T1B 4.7K CEC_A1 TPVDD12 +1.2H1
R GENERAL
no_use
METAL PLATE RESISTOR +1.2H1 TP153
100P(CH)
TP121 71 150
C124
R197
T CHINA CEC_A0/WAKEUP T1X2+
C144
C148
FIRE PROOF CARBON FILM RESISTOR
1000P(B)
1000P(B)
0.1/16(F)
0.1/16(F)
72 149
C166
C170
10/10
10/10
TP122
C151
C153
C176
10/10
HDMI_N_RST
DSDA6(VGA) T1X2-
R204
CEMENT MOLDED RESISTOR K KOREA
10K
73 148
R198
no_use
DGND DSCL6(VGA) T1X1+
SEMI VARIABLE RESISTOR A AUSTRALIA 74 147
J106 LPSVCC33 T1X1-
CHIP RESISTOR B BRITISH DGND 75 146 DGND
0 DSDA0 T1X0+
G EUROPE =YE810A0 76 145
CAPACITOR DSCL0 T1X0-
REMARKS PARTS NAME
L
E
SINGAPORE
SOUTH EUROPE
---------------
WIN=YD974A0
CBUS_HPD0
R0PWR5V
77
78 No replacement part available. 144
143
T1XC+
T1XC-
DGND
NO MARK ELECTROLYTIC CAPACITOR MX = 79
サービス部品供給なし 142 R193
DGND
V TAIWAN HDMI_PON3
DSDA_1 DSDA1 TDVDD12 +1.2H1 +1.2H1 47K
TANTALUM CAPACITOR F RUSSIAN EON= 80 141 TP151
7 DSCL_1 DSCL1 TPVDD12
C145
C149
1000P(B)
1000P(B)
0.1/16(F)
0.1/16(F)
NO MARK CERAMIC CAPACITOR 81 140
C152
C154
P LATIN AMERICA HPD_1 CBUS_HPD1 CVCC12
CERAMIC TUBULAR CAPACITOR 82 139
S BRAZIL 5VPWR_1 R1PWR5V ARC1
POLYESTER FILM CAPACITOR 83 138
H THAI DSP_BCK3 +3.3H S3.3
DSDA_2 DSDA2 ARC0 DSP_BCK3
84 137
POLYSTYRENE FILM CAPACITOR DGND DSP_WCK3
DSCL_2 DSCL2 SD1_IN/SD1_OUT/SPDIF1_IN/SPDIF1_OUT DSP_WCK3
to DIR/DSP (002.sht)
85 136 3.3
MICA CAPACITOR HPD_2 CBUS_HPD2 WS1_IN/WS1_OUT
DSP_AUP3
86 135 DSP_AUP3
P POLYPROPYLENE FILM CAPACITOR 5VPWR_2 R2PWR5V SCK1_IN/SCK1_OUT Q109 RTR020P02TL
87 134 HDMI_MCK TP154
SEMICONDUCTIVE CERAMIC CAPACITOR HDMI_MCK
3 D
2 S
DSDA_3 DSDA3 133 SD0_IN/SPDIFO_IN
88 HDMI_BCK
121
122
123
124
125
126
127
128
129
130
131
132
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
0.1/16(F)
HDMI_BCK
89
90
91
92
93
94
95
96
97
98
99
R195
C156
10K
HDMI_WCK
1
G
HDMI_WCK
XTALIN
MCLK
to DIGITAL 2/4
XTALOUT
DSCL3
DSDA4
DSCL4
RSVDL
DSDA5
DSCL5
APLL12
CVCC12
R3PWR5V
R4PWR5V
R5PWR5V
SBVCC5V
TX_HPD0
TXDSDA0
TXDSCL0
TX_HPD1
TXDSDA1
TXDSCL1
XTALGND
IOVCC33
VCC33OUT
SS/GPIO2
HDMI_SD0
CBUS_HPD3
CBUS_HPD4
CBUS_HPD5
XTALVCC33
SD0/GPIO4
SDI/GPIO5
SCK0/DDCK
SD0_0/DL0
SCLK/GPIO3
WS0_OUT/DR0
MHL_CD0/GPIO0
MHL_CD1/GPIO1
MUTEOUT/GPIO9
WS0_IN/GPIO11
HDMI_SD0
SPDIF0_OUT/DL2
SCK0_IN/GPIO10
SD0_1/DR1/GPIO6
SD0_2/DL1/GPIO7
SD0_3/DR2/GPIO8
TP158
220/6.3
R190
HDMI_SD1
C167
R194
220
HDMI_SD1
1K
HDMI_SD2
TP157
+1.2H1 C135 HDMI_SD2
R139
R151
4.7K
47K
HDMI_SD3
L118 HDMI_SD3 C2
1000P(B) B
C136 HDMI_SPDIF 3
no_use HDMI_SPDIF
IC101: SII9573CTUC L101 +1.2H1
DGND DGND
0.1/16(F) E
47k
47k
+1.2H
BLM21PG600SN1D 1
HDMI port processors &1
1000P(B)
C132
C109
C110
C112
C113
C115
1000P(B)
1000P(B)
1000P(B)
1000P(B)
0.1/16(F)
0.1/16(F)
0.1/16(F)
0.1/16(F)
0.1/16(F)
Q110
C103
C104
C105
C106
C107
C108
10/10
C175
4.7K
220/4
DTC144EKA
1000P(B)
R142
C133
DGND
4.7K
C179
DGND
0.1/16(F) HDMI_SCL
R145
Always-On C155 HDMI_SCL
100P(CH)
no_use
CEC A0 HDMI_SDA HDMI_PON1
C127
Section HDMI_SDA
10/10 DGND
CEC A1
8
DSDA_TX0
DSCL_TX0
73
5VPWR_3
5VPWR_4
HPD_TX0
CEC Interface CEC Interface
DSCL_3
DSDA_4
DSCL_4
CBUS/ Mobile HD HDMI_N_INT
HPD_3
HPD_4
Controller 0 Controller 1 72 HDMI_N_INT
HPD Control DGND
BLM21PG600SN1D
BLM21PG600SN1D
HDMI_MUTE
to CPU (004.sht)
HDMI_MUTE
78,82,86,90,94,99 CBUS0 HDMI_N_RST
AW_PRT
L104
L105
Serial Ports CBUS1 HDMI_N_RST
AW_PON
OSDROM_WRITE CB106
OSDROM_WRITE PHI
DDC0 RnPWR5V, C128
DDC1 TP127 VB39040
SBVCC5V +3.3H1
DDC Booting 1000P(B) TP161
DDC2 NVRAM Power C129 2.5 AW_PRT
SERIAL C125 S6.3 1
DDC3 EDID SRAM Sequencer 101 IC102: W25Q16CVSSIG +1.2H1 +3.3H1
to DIGITAL 4/4 TP162
AW_PON
47
0.1/16(F) 2
47
47
47
DDC4 1000P(B) TP163
R159
R155
R157
R163
DDC5 INT 3 V 16 M-bit serial flash memory with dual and quad SPI C126 TP123 DGND +5H +3.3H +1.2H S6.3
3
R140
R158
47X4
R160
47X4
ROM
TP120 130K TP164
10
DDC6 DGND
0.1/16(F) R154 4
TP165
47
69 DGND
R152
Configuration, Status, S3.3 5
R156
SFDP Register
470
HDCP Security Register 1 - 3
RF45739
RF45727
RF45710
TP166
R138
and Interrupt-Control
R164
R166
R169
I2C IC102
10K
DGND
39K
27K
10K
Local Registers OTP /CS VCC +5H 6
Registers 000000h 0000FFh 003000h 0030FFh TP117 TP167
1
XL101 3.3 S3.3
I2C 002000h 0020FFh R134 DO(IO1) /HOLD(IO3) 4 3 7
YE810A0
DDC TX TP118 TP124 TP168
3 2
5 6 7
001000h 0010FFh 2.4 3.3 S3.3
HDMI_SPDIF
47 R172
/WP(IO2) CLK HDMI_WCK
HDMI_PRT 8
HDMI_BCK
HDMI_SD0
HDMI_SD1
HDMI_SD2
HDMI_SD3
DSP_WCK3
DSP_BCK3
DSP_AUP3
TP126
HDMI_MCK
1 2 1K
470/6.3
C168
C169
47/16
Block Segmentation R135 GND DI(IO0) 27MHZ
TP119 TP125
4
10P(CH)
8P(CH)
1FFF00h 1FFFFFh 10K
no_use
xxFF00h xxFFFFh
C130
C134
R170
. . . Block 31 (64KB) .
Sector 15 (4KB)
1F0000h 1F00FFh
OSD_N_CS
TPI HW xxF000h xxF0FFh DGND
OSD_N_CS
OSD_MISO
OSD_MOSI
OSD_MISO
OSD_MOSI
OSD_SCK
E
OSD_SCK
I2S/SPDIF/ xxEF00h xxEFFFh
. Sector 14 (4KB) .
Power-Down DSD
M Main xxE000h xxE0FFh DGND DGND DGND
Section Audio Output xxDF00h xxDFFFh
R0X U 76,80,84,88,92,97
TMDS Rx Multi-Channel . .
OSDROM_WRITE
I2S/SPDIF Sector 13 (4KB)
9 10-17
(Port 0)
A X
Audio Input
xxD000h xxD0FFh
. HDMI_MUTE Page 134 M7
.
HDMI/
R1X TMDS Rx
M
U
MHL
Stream
C OSD
SPI
.
.
.
to POWER (1)_W2
(Port 1) Receiver .
Write Protect Logic and Row Decode
X Mixer
20-27 InstaPort
M
U Main
T0X xx2F00h xx2FFFh
R2X TMDS Rx X
TMDS Tx
(Port 0) HDCP
.
xx2000h
Sector 2 (4KB) .
IC103, 106: NJM2867F3-05 (TE1) IC104: RP108J131D-T1-FE IC105: TC7WHU04FU
xx20FFh
(Port 2)
28-35
SRC
Encryption 151-158 xx1F00h
.
xx1FFFh
.
10FF00h
. Block 16 (64KB)
10FFFFh
. Low dropout voltage regulator Voltage regulator Triple inverter
W25Q16CV
Sector 1 (4KB)
HDCP xx1000h xx10FFh 100000h 1000FFh
InstaPrevue
R3X TMDS Rx
Decryption
xx0F00h xx0FFFh 0FFF00h 0FFFFFh
VCC 1Y 3A 2Y
. Sector 0 (4KB) .
. Block 15 (64KB) .
39-46
(Port 3)
B D xx0000h xx00FFh
0F0000h
.
0F00FFh
VIN 5 4 VOUT VDD 2 4 VOUT
8 7 6 5
R4X Video/ .
TMDS Rx M HDMI/ Sub Write Control .
Audio /WP(IO2) 3
(Port 4) MHL T1X Logic
47-54 U Splitter M TMDS Tx Control 1 Thermal
X Receiver
InstaPort
U (Port 1) 08FF00h
. Block 8 (64KB)
08FFFFh
. 5 VFB
R5X
TMDS Rx
X
M G HDCP Encryption 141-148
080000h 0800FFh Protection
U Status 07FF00h 07FFFFh
57-64 (Port 5)
X Register . Block 7 (64KB) . Bandgap
Vref
F 070000h 0700FFh Reference
.
Current Limit 1 2 3 4
D[19..0] Parallel M .
Audio Output ENB I2S/SPDIF
Video U Sub High Voltage . Thermal Shutdown 1A 3Y 2A GND
10 1-6,161-171,174-176 Input X
2 Channel
Audio Input
Generators
00FF00h
.
00FFFFh
.
CE 1 3 GND
/HOLD(IO3) 7 Block 0 (64KB)
000000h 0000FFh Reverse Detector
CLK 6 Page Address
Video
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
SPI Latch / Counter
Pattern
/CS 1
Command
Beginning
Page Address
Ending
Page Address
GND 2
● 電圧は、内部抵抗 10MΩの電圧計で測定したものです。
Generator and
Control Logic
Column Decode
Pin No. Symbol Description ★ Components having special characteristics are marked and must be replaced ● 印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、
1 CE Chip Enable Pin (“H” Active)
ARC0/1 Rx
ARC Data
And 256-Byte Page Buffer
with parts having specifications equal to those originally installed. パーツリストに記載されている部品を使用してください。
2 VDD Input Pin
★ Schematic diagram is subject to change without notice.
136,137 DI(IO0) 5
ARC0/1 Tx
Input
GND Ground Pin
● 本回路図は標準回路図です。改良のため予告なく変更することがあります。
and DO(IO1) 2 Byte Address
3
Output Latch / Counter
4 VOUT Output Pin
5 VFB Feedback Pin
127
A B C D E F G H I J K L M N
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300 YSP-CU3300
only YSP-4300
DIGITAL 2/4
1 YSP-CU4300
DSP_AUP3
DSP_WCK3
DIR_MCK
DIR_BCK
DIR_WCK
DIR_SD0
USB_SPDIF
DSP_BCK2
DSP_BCK2
DSP_WCK2
to DIGITAL 3/4 DSP_WCK2
USB_SCK
USB_SCK
USB_MISO
USB_MOSI
USB_N_CS
USB_MISO
USB_MOSI
APL_N_CS
APL_N_RST
DSP_AUP
DSP_AUP
0.1/16(F)
0.1/16(F)
DGND
DSP_BCK3 +3.3DSP
0.1/16(F)
0.1/16(F)
2 DSP_BCK3
C313
C312
10/10
C339
C340
C341
R337
DSP_WCK3 +3.3USB
47
to DIGITAL 1/4 DSP_WCK3 R759
DSP_AUP3 47X4
DSP_AUP3
R349
47
47
R332
R339
R304 10K C350
33
10KX4
R328
2.2K
DSP_MISO 10K R305
R308
R309
0.1/16(F)
SEL_USB
DVDDIO
TEST14
TEST13
DVDDIO
SDATAO
SS_CLK
DSP_MOSI 33
TEST0
TMODE
TEST1
TEST2
TEST3
TEST4
LRCKO
SS_DO
SS_DI
SS_CS
R326
DVDD
DVSS
BCKO
2.2K
10
MDO/ADR0
9
8
7
6
C304
MDI/SDA
MPIO_B3
MPIO_B2
15 14 13 12 11
DGND
5
16 TP320
15 TP322
USB_MOSI IC305 APL_N_RST
DVDD
DGND
SCKO
LRCK
DOUT
MPO1
MPO0
0.1/16(F)
64
63
62
61
BCK
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
4
USB_N_RST R323 RESETX TEST12 R346 MFI341S2162
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
USB_MISO
1
100P(CH)
47 SCLM
C356
3
DGND TEST11
24
23
22
21
20
19
18
17
14
13
DSP_SCK MC/SCL MPIO_B1 R317 33 DSP_BCK3 33 R348 USB_CLK APL_N_CS
2
36 35 34 33 32 31 30 29 28 27 26 25
1 2 3 4 5 6 7 8 9 10 11 12
SDAM
2
AMUTE 33
DIR_N_CS MS/ADR1 MPIO_B0
3
22P(CH)
C360
1
TP326
R351
16
17
18
19
20
10K
SEL_SLAVE DVSS
R350
10K
MODE MPIO_C3 DSP_AUP
4
RXIN7/ADIN0 DIR MPIO_C2 DSP_WCK2
INREQI
USB HOST DAVDD
C344
5
AW_SD0
LRCKI LDACO 0.1/16(F)
AW_IN
RXIN6/ALRCKI0 MPIO_C1 DSP_BCK2
6
AW_WCK
IC301 BCKI VCDACO
no_use
C345
to DIGITAL 3/4
T
RXIN5/ABCKI0 MPIO_C0
7
3
AW_BCK TP327
TP335 SDATAI IC302 RDACO DGND
No replacement part available.
RXIN4/ASCKI0
PCM9211PTR MPIO_A3 ARC
8
AW_MCK
TP313 BFULLO DA_VSS
HDMI_SPDIF RXIN3 MPIO_A2 R363
BU94607ARKV-E2 サービス部品供給なし
DGND
9
DVSS VDD_PLL C346
TP336 47K
20 19 18 17 16 15 14 13 12 11 10
DIG_OPT2 RXIN2 MPIO_A1 USB_SPDIF
C348
R303 TP315 R364
R324 IRPTO TEST_PLL20.1/16(F) 330
DIR_N_RST RST MPIO_A0
DGND
47X4
16.9344MHZ
USB_N_INT SEARCH XOUT_PLL R345 9P(CH)
470P(B)
100 R318 47K
C306
R344
2
DIG_OPT1 RXIN1 NPCM/INT1 DIR_N_INT
XL302
C334
1M
33 USB_SEARCH DVDDIO XIN_PLL
VDDRX ERROR/INT0
1
C349
USB_MCHNG 0.1/16(F) MCHNG TEST_PLL1
37
38
39
40
41
42
43
44
45
46
47
48
C310
1000P(B)
0.1/16(F)
+5A
C307
TP301 R301 +3.3DSP USB_BUSY BUSY VSS_PLL 9P(CH)
XTI
XTO
VCC
+3.3DSP
AGND
FILT
VCOM
VINL
VINR
R319
RXIN0
GNDRX
VCCAD
DIG_OPT2
AGNDAD
100/16
GP1FAV51RK0F
VCC G OUT
C303
F
47 L306 10K TUN_USB_SCL SCL VOREFI
TP302 DGND
U301
0.1/10(BJ)
CB302
+5D DGND
DGND
OPTICAL C301
BLM21PG600SN1D TUN_USB_SDA R325 SDA REXTI R343
L305 PHI
10/6.3
0.1/10(BJ)
0.1/10(BJ)
C325
TP303 0.1/16 22 A0 AVSSC 12K TP344 DGND
C331
DLW21HN900SQ2L
10/16
DIG_COAX 5
C316
C319
C323
A1 USB_DP 1 2 TP345 USB_DP
4
TEST USB_DM 4 3 TP346 USB_DM
Page 132 J4
AGND
3
INPUT
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
TP347
USB_FLG
USB_FLG
2 to INPUT (2)_CB52
DIGITAL C315 L307 TP3481.2 VBUS_PRT
SD_WP
SD_CON
SD_DO
SD_CLK
SD_DI
SD_CS
VDSS
FL_CS
TEST
TEST5
TEST6
TEST7
DVDDIO
TEST8
TEST9
TEST10
DVSS
DVDD
ATEST1
ADVDD
+3.3DSP VBUS_PRT
R356
1 (YSP-CU4300)
R306
4 TP304 R302
DIG_OPT1 10/10
BLM21PG600SN1D 10K
R355
no_use
1M VB39010
GP1FAV51RK0F
VCC G OUT
TP305
47
+3.3USB +3.3DSP to CPU DGND
U302
R307
+5D DGND
TV
270
TP337 to DIGITAL 4/4
C302 10KX4 4 3 2 1
TP306 0.1/16 R331 L304
R310
680
XL301 DGND
A
5 6 7 8 BLM21PG600SN1D
4 3
0.1/16(F)
0.1/16(F)
0.1/16(F)
100/16
C342
R338
C343
C357
C347
100
1 2
4700P/25(B)
24.576MHZ
0.068/25
C322
C318
12P(CH)
15P(CH)
C311
C314
USB_IPLERR
DGND
COAX
DIG_COAX
DIG_COAX DGND DGND
to DIGITAL 4/4
+1.2DSP
Lch
Rch
+3.3DSP
I2S_SEL
R
DIGITAL IN TUN_USB_SCL
R361
TUN_USB_SCL
R358
12K
33K
TUN_USB_SDA
5 C324 C328
USB_N_INT
TUN_USB_SDA
0.01(B) 0.01(B) USB_N_INT
USB_MOSI 1.7
USB_MOSI DSP_PRT
100
100
R313
R316 USB_MISO
AGND USB_MISO
USB_SCK
USB_SCK
USB_N_CS
USB_N_CS
10/6.3
10/6.3
C321
C330
USB_N_RST
USB_N_RST
+3.3DSP +3.3D
USB_BUSY
USB_BUSY
USB_MCHNG
+3.3DSP USB_MCHNG
D
ANALOG IN IC303
USB_IPLERR
USB_IPLERR
from/to CPU
SELECT VCC USB_SEARCH Q301 RTR020P02TL
+5D USB_SEARCH
10 11 12 13 14 15 16
7 6 5 4 3 2 1
TP341
3 D
2 S
HDMI_MCK 1A ST APL_N_RST
APL_N_RST
AGND +5A
DIR_MCK 1B 4A HDMI_SD0 APL_N_CS to DIGITAL 4/4
R359
APL_N_CS
10K
BLM21PG600SN1D
1
G
TC74VHC157FT(EL
L303
SEL_MCK R327 1Y 4B DIR_SD0
C329 C333 47 R333
6 2A 4Y SEL_SD0 TP343
220/6.3
+1.2DSP
R354
C351
R357
220
DIR_N_INT
1K
C308 1000P(B) 1000P(B) 2B 3A 47 HDMI_SD1 DIR_N_INT
TP342
C327 C332 DIR_N_RST
0.1/16(F)
2Y 3B DIR_N_RST
C320
10/16
0.1/16(F)
C317
R334 DIR_N_CS C 2
C309 0.1/16(F) 0.1/16(F) GND 3Y SEL_SD1 DIR_N_CS B J301
3
9
47 DSP_MOSI
DGND C335 DSP_MOSI 2.2k 0
1000P(B) E
DSP_MISO
47k
DSP_MISO
1000P(B) 1
C336 DSP_SCK &1
DGND AGND DSP_SCK Q302
6 +5D 5.0 TP321
TP323
TP324
TP325
TP330
1 +5A 5.0 TP331
DTC123JKA
0.1/16(F)
DGND
I2S_SEL
I2S_SEL
DGND
5 DGND
3 AGND
DGND +3.3DSP
4 AUL
2 AUR
IC304 R311
DIR_WCK
W301 SELECT VCC DIR_WCK2
10 11 12 13 14 15 16
47
7 6 5 4 3 2 1
SAN-PH
HDMI_BCK 1A ST DIR_SD0 R312
ZE37170 DIR_SD02
47
DIR_BCK 1B 4A HDMI_SD2 +12D
R322
TC74VHC157FT(EL
10K
SEL_BCK R329 1Y 4B +3.3D
Analog Audio HDMI_WCK 47 2A 4Y R335 SEL_SD2
7 from PCB-INPUT DGND DIR_WCK 2B 3A
47
HDMI_SD3 TP349 12.0 +12D 1
SEL_WCK R330 2Y 3B TP350 DGND 2
47
C352
C355
R336
100/16
100/16
GND 3Y SEL_SD3 TP351 DGND 3
9
Page 131 G4 47
C337 TP352 DGND 4
to INPUT (1)_CB4 1000P(B) TP353 3.3 +3.3D 5 Page 134 M4
C338 DGND
to DIGITAL 4/4 TP354 3.3 +3.3D 6
0.1/16(F)
to POWER (1)_CB6
TP355 0.7 PRI 7
to CPU
IC301: PCM9211PTR SEL_MCK
SEL_MCK
26V_PRI
R362 TP356 AC_PDN_DET 8
216-kHz digital audio interface transceiver (DIX) with stereo ADC and routing SEL_BCK
AC_PDN_DET
100 TP357
ARC DGND SEL_BCK P_CON 9
ARC P_CON
FILT SEL_WCK
HDMI_SPDIF SEL_WCK W303
1000P(B)
1000P(B)
43
HDMI_SPDIF
C358
C359
to DSP
AUXIN0 SAN-PH
SEL_SD0
HDMI_MCK SEL_SD0 ZE37090
AUTO
HDMI Audio
RXIN7 HDMI_MCK
RXIN0 DIR DIR HDMI_BCK SEL_SD1 to DIGITAL 3/4
RXIN0 37 20 SCKO HDMI_BCK SEL_SD1
RXIN1 ADC DOUT HDMI_WCK
RXIN1 35 PLL MAIN 19 BCK SEL_SD2 DGND
OUTPUT HDMI_WCK
RXIN2 AUXIN0 HDMI_SD0 SEL_SD2
8 RXIN2
RXIN3
33
32
RXIN3 AUXIN1
SCKO/BCK/LRCK PORT 18
17
LRCK
DOUT
to DIGITAL 1/4 HDMI_SD0
HDMI_SD1
SEL_SD3
SEL_SD3
RXIN4 Lock:DIR AUXIN2 HDMI_SD1
RXIN4/ASCKIO 31 HDMI_SD2
Unlock:ADC
RXIN5 Clock/Data HDMI_SD2
RXIN5/ABCKIO 30
Recovery HDMI_SD3
RXIN6 HDMI_SD3
RXIN6/ALRCKIO 29 IC302: BU94607ARKV-E2
RXIN7 AUTO
RXIN7/ADIN0 28
USB host WAV/AAC/WMA/MP3 decoder LSI R321 RESISTOR
DIR
10KX4 REMARKS PARTS NAME
RXIN8 Lock ADC
MPIO_A0 3
Detection
DIT NO MARK CARBON FILM RESISTOR (P=5) NOTICE (model)
TESTI2/MCLK
RXIN9 AUXIN0
MPIO_A1 4 J JAPAN
TEST_PLL2
TEST_PLL1
MPIO_A CARBON FILM RESISTOR (P=10)
XOUT_PLL
VDD_PLL
VSS_PLL
VCDACO
USB_DM
SELECTOR RXIN10 AUXIN1
XIN_PLL
USB_DP
VOREFI
5 U U.S.A
RDACO
MPIO_A2 DGND
AMUTE
DAVDD
METAL OXIDE FILM RESISTOR
LDACO
TESTI1
DAVSS
AVSSC
REXTI
DVSS
RXIN11 RECOUT0 AUXIN2 C CANADA
MPIO_A3 6 METAL FILM RESISTOR
DITOUT RECOUT1 METAL PLATE RESISTOR R GENERAL
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
RECOUT0 FIRE PROOF CARBON FILM RESISTOR T CHINA
RECOUT1 MPO0/1 15 MPO0 CEMENT MOLDED RESISTOR K KOREA
SELECTOR LED_ERROR/SS_CS 61 40 AVDDC
ADC DITOUT 16 MPO1 SEMI VARIABLE RESISTOR A AUSTRALIA
Audio DAC PLL USB
VINL 47
ADC Mode
LED_PLAY/SS_DI 62
PHY 39 ATEST1 IC305: MFI341S2162 CHIP RESISTOR B BRITISH
ADC G EUROPE
VINR 48 Control LED_PSD/SS_CLK 63 38 DVDD_M2 IC digital CAPACITOR L SINGAPORE
LED_PUSB/SS_DO 64 37 DVSS REMARKS PARTS NAME E SOUTH EUROPE
9 VCOM 44 Com. Supply LED_ACCESS/LRCKO 65 Sound Effecter
Audio
Controller
USB 36 TEST10
P4/IRQ
NO MARK ELECTROLYTIC
TANTALUM
CAPACITOR
CAPACITOR
V TAIWAN
Controller F RUSSIAN
AUTO LED_RANDOM/BCKO 66
35 TEST9 Vcc H8/300H P3/IRQ NO MARK CERAMIC CAPACITOR
I/O port P2/IRQ P LATIN AMERICA
ADC Standalone DIR LED_REPEAT/SDATAO 67 Vss MICROPROCESSOR P1/IRQ CERAMIC TUBULAR CAPACITOR
MPIO_C0 7 11 MPIO_B0 34 TEST8 S BRAZIL
ADC AAC / WMA / MP3 POLYESTER FILM CAPACITOR H THAI
MPIO_C1 8 MPIO_C MPIO_B 12 MPIO_B1 DVDDIO 68
AUXOUT 33 DVDDIO POLYSTYRENE FILM CAPACITOR
MPIO_C2 9 SELECTOR AUXIN0 SELECTOR
13 MPIO_B2
Decoder System control RNG
AUXIN1 AUXIN2 TEST13 69 WDT MICA CAPACITOR
MPIO_C3 10 AUXIN1 14 MPIO_B3
IPL 32 TEST7
IC303, 304: TC74VHC157FT FMU
TEST14 70 FAT Security logic Voltage monitoring circuit
P POLYPROPYLENE FILM CAPACITOR
AUXIN2 SIO I/F 31 TEST6
Quad 2-channel multiplexer SEMICONDUCTIVE CERAMIC CAPACITOR
SEL_USB 71 File system Internal address bus
Controller 30 TEST5
ADC Clock ROM (112 kbytes)
TEST4 72
(SCK/BCK/LRCK) 29 TEST/CKL12MO
Divider SELECT 1 16 Vcc Internal data bus
XTI TEST3 73
39
OSC
SD I/F 28 FL_CS
1A 2 ASG 15 ST RES RAM (4 kbytes)
XTO 40 TEST2 74 Controller 27 DVSS
XMCKO Secondary SCK/LRCK SBCK/SLRCK 1B 3 B A 14 4A Power-on
XMCKO (To MPIO_A and MPO0/1) (To MPIO_A) EEPROM (16 kbytes + 2 kbytes)
Divider TEST1 75
Divider 26 SD_CS 1Y 4 Y B 13 4B reset circuit
Selector
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter.
NC
NC
NC
NC
NC
TMODE 76
System I2C I/F 25 SD_DI 2A 5 A Y 12 4Y
Interval timer 1
REGISTER EXTRA DIR FUNCTIONS
DVSS 77 LDO
CD-ROM I/F
Controller Controller 24 SD_CLK 2B 6 B A 11 3A ★ Components having special characteristics are marked and must be replaced
20 19 18 17 16
MC/SCL 25
SPI/I2C
Function DIR CS DIR DIR ERROR DETECTION
1 ERROR/INT0
DVDD_M1 78
23 SD_DO 2Y 7 YYB 10 3B Interval timer 2
with parts having specifications equal to those originally installed.
24 INTERFACE
★ Schematic diagram is subject to change without notice.
MDI/SDA 2 NPCM/INT1
Control (48-bit) PC and PD IS Calculator NC 1 15 NC
10 MDO/ADR0 23
Non PCM DETECTION
Is Calculator
MPIO_A
DVDDIO 79
TEST0 80
22 SD_CON GND 8 9 3Y
On-chip
Modular multiplication Register P4/IRQ 2 14 P3/IRQ
MS/ADR1 26 GPIO/GPO Flags 21 SD_PW oscillator
DIT CS DIR All Port
Data (48-bit) Interrupt IS Calculator DTS-CD/LD Detection MPIO_B coprocessor (512 bytes) Top view
NC 3 13 P1/IRQ
Validity Flag MPIO_C
User Data 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
RES 4 12 P2/IRQ ● 電圧は、内部抵抗 10MΩの電圧計で測定したものです。
RESETX
TEST15
TEST16
SEL_SLAVE
SEL_MP3/INREQI
SEL_DOUT/LRCKI
SEL_VOL/BCKI
SEL_APLAY/SDATAI
SEL_UTPKT/BFULLO
DVSS
IRPTO
SEARCH
DVDDIO
KEY_ROW1/MCHNG
KEY_ROW2/BUSY
KEY_ROW3/SCL
KEY_ROW4/SDA
KEY_COL1/A0
KEY_COL2/A1
KEY_COL3/TEST
POWER SUPPLY Channel Status Data MPO0
RST 34 Reset and BFRAME Detection 5 11
● 印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、
ADC DIR DIR
MPO1 Vcc Vss
MODE 27
Mode
Set ANALOG ANALOG ANALOG
ALL Interrupt System パーツリストに記載されている部品を使用してください。
6 7 8 9 10
● 本回路図は標準回路図です。改良のため予告なく変更することがあります。
46 45 42 41 36 38 22 21
NC
NC
NC
NC
NC
VCCAD AGNDAD VCC AGND VDDRX GNDRX DVDD DGND
128
A B C D E F G H I J K L M N
NOTICE YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300 YSP-CU3300 RESISTOR
CAPACITOR J JAPAN
(model)
REMARKS PARTS NAME U U.S.A
REMARKS PARTS NAME
DIGITAL 3/4 NO MARK CARBON
CARBON
FILM RESISTOR
FILM RESISTOR
(P=5)
(P=10)
NO MARK ELECTROLYTIC
TANTALUM
CAPACITOR
CAPACITOR
C
R
CANADA
GENERAL
1 METAL OXIDE FILM RESISTOR
METAL FILM RESISTOR
NO MARK CERAMIC CAPACITOR T CHINA
CERAMIC TUBULAR CAPACITOR K KOREA IC507: BD9329AEFJ-E2
METAL PLATE RESISTOR A AUSTRALIA
FIRE PROOF CARBON FILM RESISTOR
POLYESTER FILM CAPACITOR 1ch step-down DC/DC converter
POLYSTYRENE FILM CAPACITOR B BRITISH
+3.3DSP1 +3.3DSP1 CEMENT MOLDED RESISTOR G EUROPE
+3.3DSP1 MICA CAPACITOR
VCC
=YE768A0 C518
SEMI VARIABLE RESISTOR P POLYPROPYLENE FILM CAPACITOR L SINGAPORE
TP512 CHIP RESISTOR OPEN EN 5V
--------------- SEMICONDUCTIVE CERAMIC CAPACITOR E SOUTH EUROPE
+3.3DSP SHUTDOWN 7 VREF OSC VREG
1000P(B) V TAIWAN BST
WIN=YE243A0 C519 1
SERIAL
R509
F RUSSIAN
MX =
R508
10K
10K
TP504 P LATIN AMERICA OCP
0.1/16(F) 12V
R510
R512
R514
R516
EON= L509
no_use
S BRAZIL
4.7K
4.7K
4.7K
ROM /CS
IC503
VCC R520 N4 B8 SEL_SD0
H THAI C568
BLM21PG600SN1D
IBIAS
UVLO
VIN
2
10/10 TSD
3 2 1
6 7 8
SPI0_SCS[0] AFSR2/AXR0[0]
TP501
R507 D0 /HOLD TP513 33 TP521 R5 C8 SEL_SD1 C564
IC501
YE768A0
SPI0_ENA ACLKX2/AXR0[1] S LVS
33 TP510 R521 D81YK113CZKB400 FB ERR
/WP CLK T5 D8 0.1/16(F) 5 DRV SW OUTPUT
TP502 SPI0_CLK AXR2[3]/AXR0[2] C565
GND DI TP511 R522 P6 A7 SEL_SD2 3
CB503
5
No replacement part available. DGND
TP503 33 R6
SPI0_SIMO[0] AXR2[2]/AXR0[3]
B7 SEL_SD3 G1
1000P(B)
VCC 150601123K3 COMP SLOPE
PWM
LOGIC
DSP
11 12 13 14 15 16 17 18 19 20
to HDMI
R LVS
10 9 8 7 6 5 4 3 2 1
SPI0_SOMI[0] AXR2[1]/AXR0[4]
SW 6
サービス部品供給なし AFSX2/AXR0[5]
C7 R544
DSP_AUP
DSP_WCK1 A1 G2 R557
25
IC504
2 DSP1_N_CS TP505
TP506
P4
SPI1_SCS[0] ACLKR2/AXR0[6]
D7 47
FRONT
DSP_WF A2 Y1 47
TP564
TP565
DSP_WCK
23
SS
8 Soft Start
DSP1_N_RDY DSP1_N_RDY R523 R4 A6 DSP_F DSP_F A3 Y2 DSP_WF
5
DSP1_N_RDY SPI1_ENA AXR0[7] 22
DSP1_N_INT DSP_SCK TP507 33 T6 B6 DSP_C DSP_C A4 Y3 TP566 DSP_F
6
DSP1_N_INT SPI1_CLK AXR0[8] 21
TP508 CENTER R558 TP567 4
TC74VHC541FT(EL
DSP1_N_RST DSP_MOSI N5 C6 DSP_S DSP_S A5 Y4 DSP_C
7
DSP1_N_RST SPI1_SIMO[0] AXR0[9] 20 GND
DSP1_N_CS DSP_MISO TP509 R524 P5 D6 DSP_WF DSP_BCK1 A6 Y5 47X4 TP568 DSP_S
8
to DIGITAL 4/4 DSP1_N_CS SPI1_SOMI[0] AXR0[10] 19
DSP1_FMT 33 A5 R545 SURROUND A7 Y6 TP569 DGND
18
DSP1_FMT AXR2[0]/AXR0[11] 47X4
R515
R517
R556 R559 TP570
4.7K
4.7K
DSP_MOSI M13 SEL_MCK A8 Y7 DSP_BCK
DSP_MOSI EMA_WE/AXR0[12] 17
DSP_MISO R3 R7 47 GND Y8 47 TP571 DGND
DSP_MISO UART0_RXD/I2C0_SDA EMA_OE/AXR0[13] 16
DSP_SCK P3 P12 R560 TP572 DIR_MCK
DSP_SCK UART0_TXD/I2C0_SCL EMA_WE_DQM{1]/AXR0[14] 15
DGND M14 47 TP573 DGND
EMA_WE_DQM{0]/AXR0[15] 14
TP574 D4_N_WARNG
D4_N_WARNG 13
H5 T3
DGND TP575 D4_SCK Page 133 A5
USB0_VDDA33 AXR1[0] D4_SCK 12
E3 R2 TP576 D4_N_CS
USB0_VDDA18 AXR1[1] D4_N_CS 11 to DAMP_CB901
C3 P2 TP577 D4_MOSI
USB0_VDDA12 AXR1[2] to DIGITAL 2/4 D4_MOSI 10
P1 TP578 D4_MISO
AXR1[3] D4_MISO 9
to CPU
G4 N2 TP579 D4_N_RST
3 F4
USB0_DM
USB0_DP
AXR1[4]
AXR1[5]
N1
D4_N_RST
D4_N_DISABLE
TP580 D4_N_DISABLE
8
7
D2 M4 TP581 D4_PON
USB0_ID AXR1[6] D4_PON 6
D3 M3 TP582 D4_N_IRQ
USB0_VBUS AXR1[7] D4_N_IRQ 5
E4 M2 TP583 DGND
USB0_DRVVBUS AXR1[8] 4
TP584 IR_FLASHER
M1 3
AXR1[9] IR_FLASHER
PCB DAMP
C1 USB1_VDDA33 N3 TP585 DGND
AXR1[10] R552 SEL_MCK SEL_MCK TP586
2 IC504: TC74VHC541FT
C2 USB1_VDDA18 T4 REMOTE
JTAG for Debug AXR1[11] 47 REMOTE 1 Octal bus buffer
R550 24
F
18P(CH) DSP_BCK1
B3 B5
to HDMI
CB502 USB1_DM AHCLKX2/AHCLKX0 47
no_use C520 A3 C5 R548 to DIGITAL 4/4
1
2
USB1_DP ACLKX0 DSP_BCK2 DGND G1 1 20 Vcc
R519
47
20MHZ
XL501
TMS R501 no_use DSP1_TMS D5 R551 DSP_WCK1
1M
1
AFSX0
N_TRST R502 no_use DSP1_N_TRST F2 A4 R549 47 25
TP587 TX_N_EN A1 2 19 G2
2
OSCIN AHCLKR0 DSP_WCK2
from/to
TP543
4
18P(CH) 47 TX_N_EN 23
TDI R503 no_use DSP1_TDI R529 F1 B4 SEL_BCK TP588 RX_N_EN
3
OSCOUT ACLKR0 RX_N_EN 22
DGND C521 0 C4 SEL_WCK A2 3 18 Y1
TP589 AW_FS_N_O
4
AFSR0 21
AW_FS_N_O
PD(+3.3V) E2 OSCVSS L4 TP590
+3.3DSP AW_MISO
5
RESETOUT/AMUTE0 20
AW_MISO A3 4 17 Y2
4 KEY TP591 DGND
6
19
+1.2DSP
TDO DSP1_TDO G1 K2 TP592 AW_MOSI
7
RTC_CVDD AHCLKX1 AW_MOSI
C523 18 A4 5 16 Y3
to CPU
G2
from I2S_SEL
DGND K3 SEL_MCK TP593
DGND SEL_MCK AW_FS_I
8
RTC_OSCVSS ACLKX1 AW_FS_I 17
TCK_RET 0.1/16(F) K4 SEL_BCK TP594
SEL_BCK PWM_N_MUTE
9
AFSX1 PWM_N_MUTE 16 A5 6 15 Y4
A
DGND H1 L1 SEL_WCK TP595
SEL_WCK
14 13 12 11 10
RTC_XI AHCLKR1 1.7 DC_PRT
+3.3DSP1 DC_PRT 15
TCK R504 DSP1_TCK H2 L2 +3.3DSP1 SEL_SD0 TP596
RTC_XO ACLKR1 SEL_SD0 PWM_SDA
no_use PWM_SDA 14 A6 7 14 Y5
DGND L3 SEL_SD1 to DIGITAL 2/4 TP597
DGND AFSR1 SEL_SD1 PWM_SCL
PWM_SCL 13
N_EMU0 R505 DSP1_N_EMU0 D4 TP555 DIGITAL IN SEL_SD2 TP598 Page 133 A6
R513
SEL_SD2 DGND A7 8
R576
AMUTE1 13 Y6
10K
no_use 12
4.7K
N_EMU1 R506 SEL_SD3 TP599
SEL_SD3
no_use
+3.3DSP
J1 DAMP_PRT
1.5 DAMP_PRT
11 to DAMP_CB902
DSP1_TMS R12 TP600
TMS EMA_CLK/AHCLKR2 TP525 PWM_N_PDN A8 9 12 Y7
R575 PWM_N_PDN 10
52559-1472 DSP1_TDI J2 T7 TP601
TDI EMA_CS[3]/AMUTE2 TP526 PWM_N_RST
100 PWM_N_RST 9
DSP1_TDO R525 J3
TDO
TP602 TI_WARNG GND 10 11 Y8
33 TI_WARNG 8
ES2 DSP1_TCK H3
TCK
TP603 DGND
7
K1 TP604
RTCK/GP7[14] AW_MCK
TP514 TP519 AW_MCK 6
R
J4
to DIR
DSP1_N_TRST TP605
TRST DGND
5
DSP1_N_EMU0 J5 TP606
EMU[0] AW_BCK
to DIGITAL 2/4
5 TP515
AW_BCK
TP607 DGND
4
3
DSP1_N_RST G3 TP608
RESET
AW_SD0
AW_SD0
2 IC501: D81YK113BZKB400
TP609 AW_WCK
AW_WCK 1 Digital signal processor
R511
R518
10K
10K
24
CB504 JTAG Interface DSP Subsystem
150601123K3
DSP1_N_INT
DGND DGND DGND System Control
C674x1M
DSP MICRO-
PLL/Clock PROCESSOR
Input Generator
Clock(s) w/OSC Memory Protection
I/O Protection AET
General-
D DSP1_FMT
Purpose 32 KB 32 KB
Timer L1 Pgm L1 RAM
Power/Sleep
+3.3DSP1 Controller
General- 256 KB L2 RAM
Purpose
Timer RTC/ Pin
(Watchdog) 32-KHz Multiplexing 1024 KB L2 ROM
R553
OSC
10K
6 DSP1_EMB_A[0] D10
EMB_A[0] EMA_A[0]
T9
1
DSP1_EMB_A[1] C10 IC501 R9 TP556
EMB_A[1] EMA_A[1] Switched Control Resource (SCR)
2
DSP1_EMB_A[2] R526 B10 D81YK113CZKB400 P9 +3.3DSP +3.3DSP1
EMB_A[2] EMA_A[2]
3
DSP1_EMB_A[3] 47X4 A10 N9
C508 EMB_A[3] EMA_A[3]
4
L505
+3.3DSP1 DSP1_EMB_A[4] D11 T10
10/6.3 C569 EMB_A[4] EMA_A[4] BLM21PG600SN1D TP557
1
DSP1_EMB_A[5] C11
EMB_A[5] DSP EMA_A[5]
R10
B16
DVDD VSS
A1
Peripherals
2
C509 100/6.3 R527 E5 IC501 A2
DSP1_EMB_A[6] B11 P10 DVDD VSS DMA Audio Ports Serial Interface
C514
100/6.3
EMB_A[6] EMA_A[6] C529 D81YK113CZKB400
3
47X4 E8 A15
C524
0.1/16(F) DSP1_EMB_A[7] A11 N10 DVDD VSS
EMB_A[7] EMA_A[7] C546
4
C501 0.1/16(F) 0.1/16(F) E9 A16
VCC GND DSP1_EMB_A[8] D12 T11 DVDD VSS GPIO
44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86
EMB_A[8] EMA_A[8] C530
43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
EDMA3 dMAX McASP
1
1000P(B) E12 B2 I2C SPI UART
DSP1_EMB_D[0] 0.1/16(F) DQ0 DQ15 DSP1_EMB_D[15] DSP1_EMB_A[9] C12 R11 DVDD VSS w/FIFO
EMB_A[9] EMA_A[9] C547
DSP
2
C502 R528 0.1/16(F) F5 E6
VCCQ GND DSP1_EMB_A[10] A9 N8 DVDD VSS
EMB_A[10] EMA_A[10] C531 Control Timers Shared Memory
3
47X4 1000P(B) F11 E7
DSP1_EMB_D[1] 1000P(B) DQ1 DQ14 DSP1_EMB_D[14] B12 P11 DVDD VSS
EMB_A[11] EMA_A[11] C548 +12D
4
0.1/16(F) F12 E10
DSP1_EMB_D[2] DQ2 DQ13 DSP1_EMB_D[13] B15 N11 DVDD VSS
EMB_A[12] EMA_A[12] C532 128 KB
C511 TP554 1000P(B) G5 E11
GND VCCQ DSP1_EMB_N_RAS DVDD VSS eHRPWM eCAP eQEP RAM
4
0.1/16(F) C549 F8
G12
DSP1_EMB_D[3] DQ3 DQ12 1000P(B) DSP1_EMB_D[12] DSP1_EMB_BA0 47X4 C9 R8 DVDD VSS
BLM21PG600SN1D
3
EMB_BA[0] EMA_BA[0] C533
1000P(B) K5 F9
DSP1_EMB_D[4] DQ4 DQ11 DSP1_EMB_D[11] DSP1_EMB_BA1 R540 B9 P8 DVDD VSS Connectivity External Memory Interface
7
2
L513
EMB_BA[1] EMA_BA[1] C550
C503 0.1/16(F) K12 F10
VCCQ GND DVDD VSS
1
C534 G8
T8 1000P(B) L5
DSP1_EMB_D[5] 1000P(B) DQ5 DQ10 DSP1_EMB_D[10] DSP1_EMB_N_CS D9 DVDD VSS +1.2DSP USB2.0 EMIFA(8b/16b) EMIFB
EMB_CS[0] EMA_CS[0] C551 HPI MMC/SD
0.1/16(F) L11 G9 TP613
OTG Ctlr (8b) NAND/Flash SDRAM Only
DSP1_EMB_D[6] DQ6 DQ9 DSP1_EMB_D[9] P7 DVDD VSS PHY 16b SDRAM (16b/32b)
EMA_CS[2] C535 H8 1.2
C512 1000P(B) L12
L16
US62510
GND VCCQ L13 DVDD VSS C573
3900P(B)
EMB_CAS EMA_CAS/EMA_CS[4] C552
C580
C581
H9
10/25
100/25
0.1/16(F) M5
C582
R567 N7 TP612 L512 1000P(B)
0.1/10(BJ)
DSP1_EMB_D[7] DQ7 DQ8 1000P(B) DSP1_EMB_D[8] DSP1_EMB_N_CAS A8 DVDD VSS
C588 EMB_RAS EMA_RAS/EMA_CS[5] C536 J8
C513 R568
47 1000P(B) M8
NC NC DSP1_EMB_N_WE K15 DVDD VSS 10UH
0.1/16(F)
C578
EMB_WE C553
no_use
A 47 0.1/16(F) M9 J9
C570
R571
C510
1000P(B)
R542
10K
VCC GND 0.1/16(F) DSP1_EMB_SDCKE C13 T12 VSS
IC502
DVDD
C572
TP518 EMB_SDCKE EMA_SDCKE C566 K8
R539 47 C14 1000P(B) M12
DSP1_EMB_DQM0 0.1/16(F) DQM0 DQM1 DSP1_EMB_DQM1 DSP1_EMB_SDCLK DVDD VSS
22/6.3
C571
EMB_CLK C567 TP611
BST R574
47 +1.2DSP +1.2DSP1 0.1/16(F) R1 K9 DGND
22
DSP1_EMB_N_WE WE NC DSP1_EMB_DQM0 R569 K14 DVDD VSS
4
47 EM_WE_DQM[0] C527 R16 L7
1000P(B)
no_use
DSP1_EMB_N_CAS CAS NC DSP1_EMB_DQM1 C15
R570
R572
DVDD VSS
GND
VIN
DGND
3
30K
EM_WE_DQM[1]
SW
10/6.3 L8
DSP1_EMB_N_RAS RAS CLK DSP1_EMB_SDCLK DSP1_EMB_DQM3 R530 B13 L504 VSS
2
47X4
A12
EM_WE_DQM[2]
N6
BLM21PG600SN1D TP558
F6 L9 4 3 2 1 IC507 IC503: W25Q80BVSSIG
DSP1_EMB_N_CS CS CKE DSP1_EMB_SDCKE DSP1_EMB_DQM2
J507
CVDD VSS BD9329AEFJ
1
8 M-bit flash memory with dual and quad SPI
0
EM_WE_DQM[3] EMA_WAIT[0] G6 G
L10 5 6 7 8
NC A11 DSP1_EMB_A[9] CVDD VSS
C537 Switching frequency: 380kHz
FB
EN
SS
G7 DGND
COMMP
M6
DSP1_EMB_BA0 A22 A10 DSP1_EMB_A[8] DSP1_EMB_D[0] F16 T13
C525
VSS Security Register 3 - 0
220/4
CVDD
4
EMB_D[0] EMA_D[0] C554 G10
0.1/16(F) M7 003000h 0030FFh
0.1/10(BJ)
DSP1_EMB_BA1 A13 A9 DSP1_EMB_A[7] DSP1_EMB_D[1] R531 G13 R15 CVDD VSS
3
EMB_D[1] EMA_D[1] C538 002000h 0020FFh
C579
47X4 1000P(B) G11 M10
R573
8
1.2K
DSP1_EMB_A[10] A12 A8 DSP1_EMB_A[6] DSP1_EMB_D[2] G16 R13 CVDD VSS 001000h 0010FFh
No replacement part available.
2
EMB_D[2] EMA_D[2] C555 H6 M11 000000h 0000FFh
H13 0.1/16(F)
DSP1_EMB_A[0] A2 A7 DSP1_EMB_A[5] DSP1_EMB_D[3] P15 CVDD VSS
1
EMB_D[3] EMA_D[3] C539
1000P(B) H7 T1
サービス部品供給なし Block Segmentation
0.022/16(B)
DSP1_EMB_A[1] A3 A6 DSP1_EMB_A[4] DSP1_EMB_D[4] H16 P13 CVDD VSS 0FFF00h 0FFFFFh
4
EMB_D[4] EMA_D[4] C556
C577
DSP1_EMB_A[2] A4 A5 DSP1_EMB_A[3] DSP1_EMB_D[5] R532 J13 N15
0.1/16(F) H10
CVDD VSS
T2 DGND xxFF00h
∙ Sector 15 (4KB)
xxFFFFh
∙ ∙ Block 15 (64KB) ∙
3
EMB_D[5] EMA_D[5] C540 H11 T15 0F0000h 0F00FFh
47X4 J15 1000P(B) xxF000h xxF0FFh
DSP1_EMB_DQM2 DQM2 DQM3 DSP1_EMB_DQM3 DSP1_EMB_D[6] N13 CVDD VSS
2
EMB_D[6] EMA_D[6] C557 H12 xxEF00h xxEFFFh
C589 0.1/16(F) T16
VCC GND DSP1_EMB_D[7] J16 M15 CVDD VSS ∙ Sector 14 (4KB) ∙
1
0.1/16(F) EMB_D[7] EMA_D[7] C541 J6
C504 C515 C16 1000P(B) DGND xxE000h xxE0FFh
NC NC DSP1_EMB_D[8] N12 CVDD
W9864G2IH-7
EMB_D[8] EMA_D[8] C558 J7 xxDF00h xxDFFFh
D13 0.1/16(F)
DSP1_EMB_D[16] 0.1/16(F) DQ16 DQ31 0.1/16(F) DSP1_EMB_D[31] DSP1_EMB_D[9] R533 T14 CVDD DGND ∙ Sector 13 (4KB) ∙
3
EMB_D[9] EMA_D[9] C542 J10
C516 47X4 D14 1000P(B) xxD000h xxD0FFh
GND VCCQ DSP1_EMB_D[10] R14 CVDD
∙
2
EMB_D[10] EMA_D[10] C559 J11
0.1/16(F)
DSP1_EMB_D[17] DQ17 DQ30 1000P(B) DSP1_EMB_D[30] DSP1_EMB_D[11] D15 P16 CVDD ∙
1
DSP1_EMB_D[18] DQ18 DQ29 DSP1_EMB_D[29] DSP1_EMB_D[12] D16
EMB_D[11] EMA_D[11]
P14
C543
1000P(B) J12
CVDD NC
H4 ∙ ∙
∙
4
EMB_D[12] EMA_D[12] K6
C505 0.1/16(F) F3
VCCQ GND DSP1_EMB_D[13] R534 E13 N16 CVDD NC ∙
3
EMB_D[13] EMA_D[13] C544 K7 VDD 1 86 VSS
47X4 E16
DSP1_EMB_D[19] 1000P(B) DQ19 DQ28 DSP1_EMB_D[28] DSP1_EMB_D[14] N14 CVDD DQ0 2 85 DQ15
2
Write Protect Logic and Row Decode
EMB_D[14] EMA_D[14] K10
F13 M16 0.1/16(F) VDDQ 3 84 VSSQ
DSP1_EMB_D[20] DQ20 DQ27 DSP1_EMB_D[27] DSP1_EMB_D[15] CVDD xx2F00h xx2FFFh
1
GND VCCQ C517 DSP1_EMB_D[16] G15
EMB_D[15] EMA_D[15] C528 K11 F7 DQ1 4 83 DQ14 ∙ Sector 2 (4KB) ∙
CVDD RSV1 DQ2 5 82 xx2000h xx20FFh
+1.2DSP1
4
EMB_D[16] DQ13
10/6.3 L6 B1 J506 08FF00h 08FFFFh
VSSQ 6 81
DSP1_EMB_D[21] DQ21 DQ26 1000P(B) DSP1_EMB_D[26] DSP1_EMB_D[17] R535 H14 CVDD RSV2 VDDQ xx1F00h xx1FFFh ∙ Block 8 (64KB) ∙
3
W25Q80BV
DGND 0
EMB_D[17] 7 ∙ ∙
9 DSP1_EMB_D[22] DQ22 DQ25 DSP1_EMB_D[25] DSP1_EMB_D[18]
47X4 H15 L506
DQ3
DQ4 8
80 DQ12
xx1000h
Sector 1 (4KB)
xx10FFh
080000h 0800FFh
2
EMB_D[18] C563 79 DQ11
C506 BLM21PG600SN1D D1
VCCQ GND DSP1_EMB_D[19] J14 +1.2DSP PLL0_VDDA 0.1/16(F) VDDQ 9 78 VSSQ xx0F00h xx0FFFh 07FF00h 07FFFFh
1
DSP1_EMB_D[23] 1000P(B) DQ23 DQ24 DSP1_EMB_D[24] DSP1_EMB_D[20] K13
EMB_D[19]
C526 C545 C562 E1 DQ5 10 77 DQ10 ∙ Sector 0 (4KB) ∙ ∙ Block 7 (64KB) ∙
1000P(B) 0.1/16(F) 0.01(B) PLL0_VSSA 11 xx0000h xx00FFh
5
4
EMB_D[20] DGND DQ6 76 DQ9 070000h 0700FFh
C507 K16 12
VCC GND DSP1_EMB_D[21] R536 VSSQ 75 VDDQ
3
EMB_D[21] L507 DQ7 13 74 DQ8
0.1/16(F) C590 C591 47X4 L14
DSP1_EMB_D[22] BLM21PG600SN1D
2
EMB_D[22] NC 14 73 NC
0.1/16(F) L15 15 72
Write Control
0.1/16(F) DSP1_EMB_D[23] VDD VSS /WP(IO2) 3
1
EMB_D[23] DGND Logic
DQM0 16 71 DQM1
DSP1_EMB_D[24] A13
EMB_D[24] WE 17 70 NC
1
B14 CAS 18 69 ∙
SDRAM DSP1_EMB_D[25] R537
EMB_D[25] IC502: M12L64322A-6TG2U NC
∙
2
DGND 47X4 RAS 19 68 CLK
A14
DSP1_EMB_D[26]
EMB_D[26] 512 k x 32-bit x 4 banks synchronous DRAM CS 20 67 CKE Status
∙
3
DSP1_EMB_D[27] E14 NC 21 66 A9 Register
EMB_D[27]
4
E15 BA0 22 65 A8
DSP1_EMB_D[28]
EMB_D[28] BA1 23 64 A7
1
DSP1_EMB_D[29] R538 F14 CLK Clock 24 A6
A10/AP 63
EMB_D[29]
2
47X4 Generator Bank D A0 25 62 A5
DSP1_EMB_D[30] F15 CKE High Voltage
EMB_D[30] Bank C A1 26 61 A4
3
G14 Bank B Generators
DSP1_EMB_D[31] A2 27 60 A3
EMB_D[31] Row 00FF00h 00FFFFh
4
Address DQM2 28 59 DQM3
∙ ∙
Row Decoder
Address Block 0 (64KB)
Buffer VDD 29 58 VSS /HOLD(IO3) 7
000000h 0000FFh
Mode NC NC
10 Register
and
Refresh
Bank A
DQ16
30
31
57
56 DQ31 CLK 6
Page Address
Latch / Counter Beginning Ending
Counter VSSQ 32 55 VDDQ SPI Page Address Page Address
DQ17 33 54 DQ30
/CS 1 Command
DQ18 34 53 DQ29
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. ● 電圧は、内部抵抗 10MΩの電圧計で測定したものです。 Sense Amplifier
DQM0-3 VDDQ 35 52 VSSQ
and
Control Logic Column Decode
Command Decoder
Column
★ Components having special characteristics are marked
CS DQ19 36 51 DQ28 And 256-Byte page Buffer
and must be replaced ● 印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、 Column Decoder
Control Logic
Address 37 50 DQ27 Data
DQ20
Buffer
with parts having specifications equal to those originally installed.
Input and Output
パーツリストに記載されている部品を使用してください。 RAS VSSQ 38 49 VDDQ DI(IO0) 5
Latch Circuit
and
★ Schematic diagram is subject to change without notice. ● 本回路図は標準回路図です。改良のため予告なく変更することがあります。 Refresh DQ21 39 48 DQ26
Buffer
CAS 47
Counter DQ22 40 DQ25 DO(IO1) 2 Byte Address
Data Control Circuit DQ 46
VDDQ 41 VSSQ Latch / Counter
WE
DQ23 42 45 DQ24
VDD 43 44 VSS
129
A B C D E F G H I J K L M N
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300 YSP-CU3300
DIGITAL 4/4
1
J706
0
CB704
8
S3.3 R761 TP787
1
N_RESET
100 TP788
2
R762 TP789
3
100
J705 TP790 RS-232C
R757
R758
47K
47K
4
IR_IN
REM_IN
N_RESET
no_use
232C_CTS
FLASH_RXD
FLASH_TXD
TP791
AC_PDN_DET
R763
5
100 TP792
S3.3 R764
232C_CTS 100
6
C702
232C_RTS 7
0.1/16(F) V+
FLASH_TXD MJ-66J-RD315
5 DGND
R714 FLASH_RXD
22 TP716
TUNER_GPIO
BLM21PG600SN1D
3 L701
V- IC706
TC7SH08FU S3.3
0.1/16
C726
DGND
2
DOUT1
ROUT1
ROUT2
RIN1
DIN1
DIN2
VCC
GND
DIR_SD02
16 15 14 13 12 11 10 9
DSP_SCK
DIR_N_CS
DSP_MISO
DSP_MOSI
DIR_N_INT
DSP1_N_CS
DIR_N_RST
S3.3
DSP1_N_INT
DIR_WCK2 DGND
DIR_WCK2 IC710 MAX3232CPWR
DIR_SD02 1 2 3 4 5 6 7 8
DIR_SD02
232C
V+
V-
C1+
C1-
C2+
C2-
RIN2
DOUT2
R769
DIR_N_INT
4.7K
DIR_N_INT C734
REMOTE
DGND
DIR_N_RST
DRIVER
0.1/16
0.1/16
C727
DIR_N_RST 22P(CH)
C730
0.1/16
DIR_N_CS
from/to DIR/DSP
C732
DIR
DIR_N_CS
S3.3 C729
D4_PON
D4_SCK
AW_MOSI
D4_N_CS
D4_MISO
D4_MOSI
PWM_SCL
PWM_SDA
D4_N_IRQ
D4_N_RST
TI_WARNG
PWM_N_RST
PWM_N_PDN
D4_N_WARNG
PWM_N_MUTE
I2S_SEL
D4_N_DISABLE
I2S_SEL
to DIGITAL 2/4 DSP_PRT 0.1/16
DSP_PRT DGND
R771
4.7K
DSP_MOSI VBUS_PRT
DSP_MOSI S3.3
DIR&DSP
VBUS_PRT
to POWER
DSP_MISO
DSP_MISO AC_PDN_DET
R737 33
33
33
33
R732 33
33
33
33
DSP_SCK AC_PDN_DET
DSP_SCK to DIGITAL 2/4
R734
R742
R720
R722
R724
R731
R738
4.7K
26V_PRI
33X4
33X4
R717
R727
R741
26V_PRI
4.7K
DSP1_N_RDY
DSP1_N_RDY P_CON
T
DSP1_N_INT P_CON
3 DSP1_N_INT
R740
DSP1_N_RST
22
DSP
to DIGITAL 3/4 DSP1_N_RST S3.3
DSP1_N_CS CB703
DSP1_N_CS PHI
3.3
DSP1_FMT STBY_SW TP783 STBY_SW
DSP1_FMT
TO/FROM KEY
1
TP784 3.3 S3.3
100P(SL)
C710
Page 135 D2
0.1/16
2
C728
C731
TP785 DGND
0.1/16(F) 3
C709 TP786 3.3 KEY1 to POWER (3)_W951
R713
R766 R767 KEY1
10K
4
D4_N_DISABLE
S3.3 YSP-CU4300 no_use 10K
AC_PDN_DET
D4_N_WARNG
TUNER_GPIO
DSP1_N_INT
0.1/16(F)
PWM_N_MUTE
DIR_N_RST
DIR_N_INT
FLASH_RXD
FLASH_TXD
FLASH_RXD
PWM_N_RST
PWM_N_PDN
DSP1_N_CS
YSP-CU3300 10K no_use VB39000
DSP_MISO
D4_N_IRQ
232C_CTS
D4_N_RST
DIR_N_CS
DSP_MOSI
TI_WARNG
DSP_SCK
D4_N_CS
D4_MISO
D4_MOSI
PWM_SCL
PWM_SDA
N_RESET
DGND
AW_MOSI
D4_PON
D4_SCK
VREFH
F
AVss
no_use
DVss
MODE
R773
AW_MISO
TP731,800 A
INPUT NG
9
8
7
6
5
4
3
2
1
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
USB_N_INT AW_MISO DSP_PRT DSP_PRT
37 144
D4_N_IRQ DSP1_N_RST DC_PRT DC_PRT R760
D4_N_IRQ 38 143
D4_N_CS DSP1_N_RST R705 26V_PRI 100
USB_N_INT 26V_PRI S3.3
D4_N_CS 39 142 no_use
D4_N_RST DSP1_N_RDY DSP1_N_RDY DAMP_PRT DAMP_PRT C725
D4_N_RST 40 141
DSP1_FMT DSP1_FMT DEST_N_WR TP731 TP800
DGND
D4_N_DISABLE
D4_N_DISABLE 41 140 5 V+0.1/16
4 D4_MISO
D4_MISO
D4_SCK
USB_MOSI
USB_MISO 33X4
USB_MOSI
USB_MISO
42 139
DIR_WCK2
MODEL R766 no_use
DIR_WCK2
MIC_N_DET R756 4
1 DGND
D4_SCK 43 138 MODEL: H=4300, L=3300 no_use
R706 TP756 2
D4_MOSI USB_SCK USB_SCK TP747 R767 10K
D4_MOSI IC709
1000P(B)
44 137
V- 3
C735
DAMP_PRT USB_N_CS USB_N_CS AW_PRT AW_PRT TC7SH08FU
DAMP_PRT 45 136 no_use
A
TI_WARNG HDMI_PRT HDMI_PRT
TI_WARNG 46 135 CB702
TP710 DGND
0.1/16(F)
D4_N_WARNG
D4_N_WARNG DVcc3
MICROPROCESSOR 28FMN-BMTTN-A-T
C703
47 134
PWM_N_RST 33X4 DVss VBUS_PRT VBUS_PRT
PWM_N_RST INPUT_PRT TP757 INPUT_PRT 2.0
48 133
1
PWM_N_PDN INPUT_PRT INPUT_PRT TP758
PWM_N_PDN 49 132 DGND
2
PWM_N_MUTE AW_FS_N_O AW_FS_N_O KEY1 R728 KEY1 TP759
PWM_N_MUTE 50 131 TUNER_GPIO TUNER_GPIO
to DIGITAL 3/4
3
D4_PON AVcc R746 47
TP760
0.01/16(B)
D4_PON 51 130 TUN_N_RST TUN_N_RST
0.1/16(F)
TMPM362F10FG
4
10K
C712
C717
DC_PRT AW_RX_EN HDMI_CEC CEC TP761
DC_PRT R702 52 129 MIC_N_DET
5
PWM_SCL 47K RX_N_EN R708 FLASH_N_BOOT FLASH_N_BOOT
AW_TX_EN TP762
S3.3
PWM_SCL 53 128 TUN_USB_SCL TUN_USB_SCL
YSP-CU4300
6
PWM_SDA R703 TX_N_EN TEST2 TP735 TP763
PWM_SDA TP796 54 127 TUN_USB_SDA TUN_USB_SDA
R765
47K
7
47K
4300 only I2S_SEL I2S_SEL TEST1 TP736 TP764 DGND
AW_MOSI 55 126
8
R701 10K
R
AW_MOSI USB_N_RST USB_N_RST NMin TP765
10KX4 56 125 USB_N_PON USB_N_PON
AW_MISO
9
AW_MISO USB_BUSY 33X4 USB_BUSY P_CON R744 P_CON
FLASHER_PON TP766 FLASHER_PON
57 124
IC701
28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
RX_N_EN
5 RX_N_EN
TX_N_EN
USB_MCHNG USB_MCHNG
58 123
232C_RTS R748
33
232C_RTS
HDSUR_LED TP767
HDSUR_LED
TX_N_EN USB_IPLERR USB_IPLERR REGVss TP768
59 122 S3.3_2_PON1 S3.3_2_PON1
USB_SEARCH USB_SEARCH DVcc3 TP769
AW_FS_N_O SDSUR_N_LED SDSUR_N_LED
FFC/1mm/FMN
60 121
0.1/16(F)
AW_FS_N_O
to INPUT
TP740
C713
APL_N_RST R711 X2
no_use
AW_FS_I APL_N_RST FL_SCK TP770 FL_SCK
XL702
10MHZ
61 120
R750
AW_FS_I 33
DGND APL_N_CS R712 APL_N_CS CVss TP771
FL_MOSI FL_MOSI
62 119 Page 131 L5
0.1/16(F)
33 TP741
C714
REMOTE P-GOOD P-GOOD X1 TP772
REMOTE 63 118 18P(CH) FL_N_CS FL_N_CS
4300 only
64 No replacement part available. 117
CVcc3
TP742 C721
FL_N_RST TP773 FL_N_RST to INPUT (1)_CB8
XT2
サービス部品供給なし
no_use
TP774
XL701
YSP-CU4300 65 116 32.768KHZ SW_N_MUTE SW_N_MUTE
R749
XT1 TP743 WG97080
ISEL_CNT2 TP775 ISEL_CNT2
66 115
REGVcc3 18P(CH)
ISEL_CNT1 TP776 ISEL_CNT1
67 114
0.1/16(F)
D C715
HDMI_MUTE C722 TP777
68 113 IR_IN IR_IN
DGND
TP797 CEC_CHECK HDMI_N_RST R747 TP778
69 112 DGND
TP798 22
HDMI_SCL TP779
70 111 HDMI_MUTE IR_FLASHER
USB_N_INT IR_FLASHER
USB_N_INT TP799 HDMI_SDA TP780
71 110 HDMI_N_RST DGND
USB_MOSI
USB_MOSI PWR_N_LED R715 PWR_N_LED HDMI_PON3 TP781
72 109 HDMI_SCL DIG_COAX
100
101
102
103
104
105
106
107
108
USB_MISO to DIGITAL 2/4 DIG_COAX
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
33
USB_MISO HDMI_SDA TP782 DGND
6 USB_SCK
USB_SCK
TP793
DVss
DVcc3
AW_PON
PWR_N_LED
FL_SCK
SWD_IO
REM_IN
PWR_N_LED
E2P_SCK
FL_N_CS
FL_MOSI
SWD_SCK
SWD_SWV
STBY_SW
FL_PON
E2P_N_CS
E2P_MOSI
ISEL_CNT1
E2P_MISO
FL_N_RST
AW_FS_I
USB_FLG
USB_PON
ISEL_CNT2
MIC_N_DET
TUN_N_RST
HDSUR_LED
OSD_WRITE
HDMI_PON1
DIGITAL IN
HDMI_N_INT
SW_N_MUTE
S3.3_2_PON1
TUN_USB_SDA
TUN_USB_SCL
HDMI_PON2
USB_N_CS
FLASHER_PON
SDSUR_N_LED
USB_N_CS FL_PON TP794 FL_PON
TP726
TP728
TP730
TP732
USB_FLG USB_FLG
USB_N_RST C707
USB_N_RST
to DIGITAL 2/4 USB_BUSY
TUN_USB_SCL TUN_USB_SCL
USB_BUSY 0.1/16(F) DGND
TUN_USB_SDA
USB_MCHNG S3.3 TUN_USB_SDA
USB_MCHNG
USB_IPLERR S3.3
USB_IPLERR to DIGITAL 2/4
USB_SEARCH
USB_SEARCH
100/16
APL_N_RST
C719
R772
4.7K
APL_N_RST
R770
33
APL_N_CS AW_PRT
APL_N_CS AW_PRT
HDMI_PRT
AW_FS_I HDMI_PRT
CEC
DGND CEC
to/from 001.sht
HDMI_N_RST
HDMI_N_RST
HDMI_MUTE
33
HDMI_MUTE
HDMI_SCL
HDMI
R768
R721
R735
R739
R743
33X4
33X4
33X4
33X4
33X4
HDMI_SCL
33
R719
R723
R725
33
7 HDMI_SDA
HDMI_SDA to DIGITAL 1/4
HDMI_PON3
HDMI_PON3
S3.3
HDMI_PON2
RESISTOR HDMI_PON2
NOTICE (model) HDMI_PON1
REMARKS PARTS NAME J JAPAN HDMI_PON1
OSDROM_WRITE
R733
R736
OSDROM_WRITE
100K
NO MARK CARBON FILM RESISTOR (P=5) OSDROM_WRITE
33
U U.S.A
HDMI_N_INT
HDMI_PON1
HDMI_PON2
HDMI_PON3
HDMI_N_INT
CARBON FILM RESISTOR (P=10) C CANADA HDMI_N_INT
AW_PON
AW_PON
METAL OXIDE FILM RESISTOR R GENERAL 4300 only AW_PON
METAL FILM RESISTOR T CHINA
YSP-CU4300
METAL PLATE RESISTOR K KOREA
FIRE PROOF CARBON FILM RESISTOR A AUSTRALIA
SDSUR_N_LED
FLASHER_PON
S3.3_2_PON1
TUN_USB_SDA
TUN_USB_SCL
CEMENT MOLDED RESISTOR B BRITISH
SW_N_MUTE
ISEL_CNT1
ISEL_CNT2
USB_N_PON
MIC_N_DET
TUN_N_RST
HDSUR_LED
FL_N_RST
FL_N_CS
FL_MOSI
USB_FLG
SEMI VARIABLE RESISTOR G EUROPE
FL_PON
FL_SCK
CHIP RESISTOR L SINGAPORE
TP755 SW701
FLASH_N_BOOT 2 1
E SOUTH EUROPE
SKHLLC
V TAIWAN
8 CAPACITOR
F RUSSIAN
(RESET) DGND
E2P_N_CS
E2P_MOSI
E2P_MISO
P LATIN AMERICA
E2P_SCK
STBY_SW
REM_IN
REMARKS PARTS NAME S BRAZIL
NO MARK ELECTROLYTIC CAPACITOR H THAI
TANTALUM CAPACITOR
P-GOOD
E2P_SCK
N_RESET
STBY_SW
E2P_MISO
E2P_N_CS
E2P_MOSI
N_RESET
NO MARK CERAMIC CAPACITOR
CERAMIC TUBULAR CAPACITOR
POLYESTER FILM CAPACITOR
POLYSTYRENE
MICA
FILM
CAPACITOR
CAPACITOR
RESET IC PN702 PN703
22
IC704 S3.3
P POLYPROPYLENE FILM CAPACITOR
EEPROM
R716
R3116N271A-TR-F
+3.3DSP1 S3.3
SEMICONDUCTIVE CERAMIC CAPACITOR V963750 V963750
TP734
CD OUT
S3.3
5
FORCED RESET
R718
IC703 PN701
47K
VDD
330P(SL)
R1EX25032ASA00A Q701
2
0.1/16
C708
C711
TP715 TP722 RTR020P02TL NC GND
%S& VCC 3 2
4
IC701: TMPM362F10FG
1
8
TP714
R754
OUT CD
120K
D S
5
1
TP718 Q HOLD
330P(SL)
R755
2
7
0.068/16
32-bit RISC microprocessor
0.1/16(F)
VDD V963750
R730
0.1/16(F)
0.1/16
10K
1G DGND DGND
C733
10K
TP752
C704
C705
2
TP717
0.1/16
W C
R704
R726
C701
2.2K
9
47K
C706
C716
3
GND NC TP751 2 Q704
V+
4
3
TP720
0.1/16
TP739
VSS D
R753
Q703 C
C723
4
470
IC702 2 5 V+ 10k 3
R729
ETM Cortex-M3 TP721 C TP750
DMA R3116N301C-TR-F 10k 2
1K
3 8 B
4
TP753
Controller 2 6 R752 5 3 7 1 TP754
10k
SWD NVIC &1 B
DGND 1 E Q705
10k
2 47K 1 2
C B E TP748 C
DGND 3 3 IC708 4
1 10k 3
C720
1/16
C724
V- TC7W14FK DTC114EKA
100/16
47k V- B
E DTC114EKA IC707
47k
TC7SH08FU
10k
AHB Lite Bus Matrix E
1
Q702 1
DTC144EKA DTC114EKA
DGND
FLASH (1MB)
CG DGND
RAM (56KB) PORT
WDT
IC702: R3116N301C-TR-FE IC703: R1EX25032ASA00A IC704: R3116N271A-TR-F IC706, 707: TC7SH08FU IC708: TC7W14FK IC710: MAX3232CPWR
Backup RAM
Voltage detector ICs 4096 x 8-bit SPI serial interface EEPROM Voltage detector ICs 2-input AND gate Schmitt inverter 3-V to 5.5-V multichannel RS-232 line driver/receiver
★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. (8KB)
RTC
AHB to I/O Bridge
★ Components having special characteristics are marked and must be replaced
AHB Lite Bus 0
16bit Timer
High voltage generator C1+ 1 16 VCC
SMC VDD 2
with parts having specifications equal to those originally installed. SIO/UART VDD 2 Vcc 8
IN B 1 5 VCC 1A 1 8 VCC
10 ★ Schematic diagram is subject to change without notice. (4byte FIFO)
Vss 4
V+ 2 15 GND
decoder
I2C/SIO Delay
Address generator
Delay
1 OUT Memory array Circuit
1 OUT
IN A 2 3Y 2 7 1Y C1- 3 14 DOUT1
Control logic
10bit ADC Circuit S 1
X
C2+ 4 13 RIN1
● 電圧は、内部抵抗 10MΩの電圧計で測定したものです。 BOOT ROM CEC W 3
● 印のある部品は、安全性確保部品を示しています。部品の交換が必要な場合、 RMC
Vref Vref GND 3 4 OUT Y 2A 3 6 3A C2- 5 12 ROUT1
C 6
decoder
3 GND Y-select and Sense amp. 3 GND
パーツリストに記載されている部品を使用してください。 KWUP
HOLD 7 5 V- 6 11 DIN1
5 GND 4
● 本回路図は標準回路図です。改良のため予告なく変更することがあります。 5 2Y
Y
D 5 CD 7 10 DIN2
AHB to APB Bridge CD DOUT2
SSP Q 2 Serial-parallel converter
RIN2 8 9 ROUT2
130
A B C D E F G H I J K L M N
YSP-CU4300/YSP-CU3300/NS-WSW160
YSP-CU4300 YSP-CU3300
INPUT 1/2
1
[Tuner] YSP-CU4300 IC4: KIA78M05F
Three terminal positive voltage regulator
CB1
TUN_N_RST
1 R1067, R1068
TUN_USB_SDA
2 YSP-CU4300 22 1
TUN_USB_SCL YSP-CU3300 no_use
RA
RB
1
3 INPUT
CONTACT SIDE
D2
R4
GPIO
4
R13_1
To TUNER
R1068
22
5
R1067
Q9
22
GND Q8
6
Rch OUT Q12 Q15
7
+5A 6kHz 6kHz
8 +5A Q16
Lch OUT R1015 +5D +5A
D1008
+12A +12D D3 R15
9
YSP-CU4300 Page 132 J3 R14
C1005
0.1/16
1.5K
to FM TUNER
no_use C1013
1SS355VM
no_use
C1008
C1012 10/16
52045 R1012
5.0 IC4 12.0 Q14
KIA78M05F
VQ04720
1.5K L1003 OUT IN L1004
to INPUT (2)_CB52 R19
R16
R12
68UH 68UH USB_PON Low HIGH
(YSP-CU4300)
100/6.3
C1051
C1053
0.1/16
0.1/16
C1050
C1054
47/16
COM
10/10 EN Hi/Hi-Z LOW 3
C1048
C1049
C1057
C1058
10/16
10/16
10/16
10/16
-1.2dB
AGND AGND C1025 +5USB ON OFF Q6
VBUS D1 OUTPUT
R1019
R1021
10/10
Q10
2
10K
10K
TUNER OUTPUT:MAX1.1Vrms(Over Mod) J1002
J1001 J1003 Switching frequency: 570kHz
C1026 5.9 VBUS XHI
R20
+26D
L1005 5.9 QD
R18
C1062 VBUS 4
R9
TO USB
0.1/16
DGND AGND AGND DGND VBUS
C1075
DGND AGND 10UH 3
R2
26.0 0.1/16
RB050L-40
22/10
AGND DGND Q11
no_use
C1068
22/10
D1009
C1065
C1067
2
BOOT VOUT C1
R1076
1
R11
Q1
15K
DGND
VIN GND 1
R1083
2
1P100
DGND CB5
EN COMP
Q4
6
SS VSNS
5
Q13
0.01(B)
C1059
C1060
R21
10/35
Q1 Q2
R1081
IC5
1P100
R1077
TPS54331DR
0.018/25
R13
10K
0.018/25
C1064
C1061
R3
22P(CH)
C1063
R1078
R1069
3.9K
+12A 0
30K
DGND
R1027
DGND
3.9
570kHz
DGND
DGND
INTELLIBEAM MIC R1013 R1020
L1002 4.7K 4.7K NJM2068MD-TE2 HDSUR_LED
V+ 8 S3.3
10 11 12 13 14 15 16 17 18 19 20
MMZ1608Y601 10/10 R1024 5
SDSUR_N_LED
2 R1007 7 R1035
T
OPTIMIZER C1017 220 IC2
100P(SL)
3 6 DGND
C1019
2.2K 47
3
R1086
DGND
MIC
100K
C1002
20FMN-BMTTN-A-T
R1028 PWR_N_LED
no_use
JK1
HZU5.1B2 12K IC1: TC7WHU04FK
47/16
C1014
DGND
D1001
INPUT SELECTOR
LGY6501-0900FC NJM2068MD-TE2
C1022 Q1014
R1025
Triple inverter
R1011
FL_MOSI
100K
1
10K
2 S3.3
R1026
IC2
47/16
C1023
33P(CH)
P
470
Q1027 DGND
MIC IN 3 +5A CNT1 CNT2 IN1 IN2 IN3 IN4 DTA014EUBTL
4 FL_SCK
TO/FROM FL
V-
L L NC
VCC 1Y 3A 2Y
R1022
C1080
0.1/16
10/10
H L Tun DGND
C1020
47K
DTC044EUBTL
C1045
L
H
H
H
MIC
AUX
FL_N_CS Page 135 D8 8 7 6 5
CB7
F1
DTC044EUBTL DGND
IN1a GND 100/16 Q1032
to POWER (2)_CB901
9 10 11 12 13 14 15 16
DGND
8 7 6 5 4 3 2 1
F2 FL_N_RST
CNT1 OUTa R1063 +12D
9
IC3
DGND
C1046 47 +3.3D DGND
IN2a V+
8
AGND
+3.3D 3.3
F
CNT2 IN3a C1052 R1066 J1005 +3.3D
L 0.1/16
7
NJM2750M(TE1)
C1047 DTA014EUBTL +30V
IN4a Vref 10/10 1.2K no_use +30V
6
R1065
Q1019/Q1020 +30V 30.0
1K
+30V
IN1b OUTb R 10/10 R1064 ROHM 2SC5866-TL WJ46640
5
RSR025P03TL
ANALOG IN IN2b N.C 47 Q1028 FL_F2
4
L1006 F2
FL_F2
R1061
R1062
IN4b IN3b
100K
100K
3
100UH
T1001 Q1031 1 2 3 4
R1109
AGND +12D FL_F1
R1089
10K
10 2
2
F1
8.2K
R1073
100/50
C1069
MSD-252V-04 FL_F1 3.0
10K
Q1019 1A 3Y 2A GND
470/25
1 3
1
C1071
R1002 R1005 C1015 ANALOG INPUT SELECTOR DTA014EUBTL
R1108
7 4
L S3.3
1K
220 12K 10/10
Page 128 E7
0.01(B)
220P(SL)
C1070
8 6
C1009
AGND CPH3205
R1009
8.2K
9 5 Q1033
4 INPUT CPH3205
no_use
to DIGITAL_W301
AGND
HZU5.1B3
0.1/50(F)
DGND
ANALOG ANALOG IN 1 10RJG Q1029
C1066
D1010
R1094
1P4.7K
Q1030
220P(SL)
C1010
R1010
Q1020
8.2K
( AUX )
DAP222
DAN222
D1012
D1011
DTC044EUBTL
C1016
no_use
R1053
R1003 R1006 C1055
R Q1012
TO DITIGAL
A
220 12K 10/10 CB4
5.0 +5A DTC014EUBTL
PJ3 +5A
0.1/16 DGND
IC2: NJM2068MD-TE2
AUR DGND
AGND AGND DGND
AGND DGND Dual operational amplifier
AGND
Q1006 Q1008 AUL
R1034 R1044 DGND
DGND
no_use no_use 5.0+5D
OUT1 1 8 +VCC
+5D
no_use no_use
C1056 PHI
0.1/16 FL_PON –IN1 2 7 OUT2
1
+ – + –
PWR_N_LED
2
PJ1 DGND +IN1 3 6 -IN2
3
R1001 R1032 R1043 DIG_COAX
4
no_use
–VCC 4 5 +IN2
FROM DAMP
SubWoofer no_use no_use DGND
C1007
CB2
no_use
5
SW_OUT
CB8
OUT IR_FLASHER
C1001
6
AGND
G DGND
7
no_use
5 no_use AGND
no_use IR_IN
8
ISEL_CNT1
9
EARTH TERMINAL of PJ901
ISEL_CNT2
28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
SW_N_MUTE
P
TO/FROM DIGITAL
FL_N_RST
FL_N_CS
28FMN-BMTTR-A-T
FFC/1mm/FMN
TUN_USB_SCL/SDA
FL_MOSI
Page 130 M5
+3.3D
FL_SCK
IC3: NJM2750M-TE2
SDSUR_N_LED
to DIGITAL_CB702 4 input /1 output stereo audio selector
S3.3_2_PON1
HDSUR_LED
FLASHER_PON
FLASHER_PON
R1071
R1074
R1079
USB_PON
2.2K
2.2K
4.7K
IN1a 1 16 GND
D
DGND
Remote control TUN_USB_SDA
sensor TUN_USB_SCL
CNT1 2 15 OUTa
MIC_N_DET
S3.3
&2 s3 s4
IR_IN S3.3
TUN_N_RST
V+
JK2 s1 L1001 R1030 TUNER_GPIO IN2a 3 14 V+
D1002
GP1UE281QKVF
IR IN IR_IN IR_IN
s6
10 DGND
22P(CH)
22P(CH)
C1091
C1092
R1082
PZ2012U600-3R0T
R1031
4.7K
10K
U1001 INPUT_PRT 2.8
6
s5
LGY6501-0900FC
(U, C, T, B, G, F models)
0.01(B)
R1048
CNT2
R1039
4 13 IN3a
100K
C1004
LOGIC
s2
s26
s7
47
s8
SIR-505STA47
GND
VCC
0.01(B)
VOUT
DGND
C1006
s2
You might also like
- Yamaha Yas-207 - Ats-2070 - Cu207 - Ats-Cu2070 - ns-wsw42 PDF50% (2)Yamaha Yas-207 - Ats-2070 - Cu207 - Ats-Cu2070 - ns-wsw42 PDF50 pages
- Yas-209 - Cu209 Ats-2090 - Cu2090 NS-WSW44No ratings yetYas-209 - Cu209 Ats-2090 - Cu2090 NS-WSW4442 pages
- Hfe Yamaha rx-v4600 Dsp-Ax4600 Service en PDFNo ratings yetHfe Yamaha rx-v4600 Dsp-Ax4600 Service en PDF144 pages
- Home Theater System: Service Manual Service Manual100% (2)Home Theater System: Service Manual Service Manual42 pages
- RX-V863/HTR-6180/ DSP-AX863SE/DSP-AX863: Av Receiver/Av AmplifierNo ratings yetRX-V863/HTR-6180/ DSP-AX863SE/DSP-AX863: Av Receiver/Av Amplifier155 pages
- Documentation For Approval: TO: Customers DATE: 2005.09.26100% (1)Documentation For Approval: TO: Customers DATE: 2005.09.2636 pages
- Key Concepts in Electromagnetic InductionNo ratings yetKey Concepts in Electromagnetic Induction45 pages
- VacuAide QSU Portable Suction Unit GuideNo ratings yetVacuAide QSU Portable Suction Unit Guide4 pages
- Terminal 2: Level 4 - Retail Mezzanine - Part Plan - 64No ratings yetTerminal 2: Level 4 - Retail Mezzanine - Part Plan - 641 page
- HoneywellControLinksS7999ConfigurationDisplay 732No ratings yetHoneywellControLinksS7999ConfigurationDisplay 73232 pages
