NSX-BL44 EZ,K,G

NSX-BL46 EZ

NSX-DR6 EZ

SERVICE MANUAL
ex.denom.com
COMPACT DISC
STEREO SYSTEM
BASIC TAPE MECHANISM : 6ZM-3 PR2NM(44/46)
BASIC TAPE MECHANISM : 6ZM-3 YPR2N(DR6)
BASIC CD MECHANISM : AZG-1 ZA3RDM(44/46)
BASIC CD MECHANISM : AZG-1 YZA3RDM(DR6)

CD REMOTE
SYSTEM SPEAKER
CASSEIVER CONTROLLER
NSX–BL44
CX–NBL44 SX-NSZ53
(G)
NSX–BL44
CX–NBL44 SX–NBL40
(EZ/K)
RC–ZAS01
NSX–BL46
(EZ) CX–NBL46 SX–NBL42
NSX–DR6
(EZ) CX–NDR6 SX–NBL40

If requiring information about the CD mechanism, see Service Manual of AZG-1

(S/M Code No. 09-001-335-3NC).
TA
DA

S/M Code No. 09-002-429-5N2

 SPECIFICATIONS

Main unit CX-NBL44, CX-NBL46, CX-NDR6 Cassette deck section

FM tuner section Track format 4 tracks, 2 channels stereo
Tuning range 87.5 MHz to 108 MHz Frequency response 50 Hz – 15000 Hz
Usable sensitivity (IHF) 16.8 dBf Recording system AC bias
Antenna terminal 75 ohms (unbalanced) Heads Deck 1: Playback head x 1
Deck 2: Recording/playback head
AM (MW) tuner section x 1, erase head x 1
Tuning range 531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step) Compact disc player section
Usable sensitivity 350 µV/m Laser Semiconductor laser (λ = 780 nm)
Antenna Loop antenna D-A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
LW tuner section Harmonic distortion 0.05 % (1 kHz, 0 dB)
Tuning range 144 kHz to 290 kHz Wow and flutter Unmeasurable
Usable sensitivity 1400 µV/m
Antenna Loop antenna
General
Amplifier section Power requirements 230 V AC, 50 Hz
Power output Rated: 80 W + 80 W (6 ohms, Power consumption 150 W
T.H.D. 1 %, 1 kHz/DIN 45500) Power consumption in standby mode
Reference: 100 W +100 W (6 ohms, If the power-economizing mode is
T.H.D. 10 %, 1 kHz/DIN 45324) ECO OFF: 20 W
DIN MUSIC POWER: If the power-economizing mode is
200 W + 200 W ECO ON or ECO AUTO: 0.9 W
Total harmonic distortion 0.1 % (45 W, 1 kHz, 6 ohms, DIN Dimensions of main unit 260 x 326 x 346 mm
AUDIO) (W x H x D)
Weight of main unit 8.2 kg
Inputs VIDEO/AUX: 500 mV
Outputs SPEAKERS: Speaker system SX-NBL40, SX-NBL42, SX-NSZ53
accept speakers of 6 ohms or more Speaker system 3 way, Bass reflex (magnetic
SURROUND SPEAKERS: shielded type)
accept speakers of 8 ohms to 16 Speaker units Woofer: 140 mm cone type
ohms Tweeter: 60 mm cone type
PHONES (stereo jack): accepts Super tweeter: 20 mm ceramic type
headphones of 32 ohms or more Impedance 6 ohms
Sensitvity 87 dB/W/m
Dimensions (W x H x D) 220 x 324 x 230 mm <40, 42>
240 x 324 x 270 mm <53>
Weight 4.0 kg

• Design and specifications are subject to change without notice.

• The word “BBE” and the “BBE symbol” are trademarks of BBE
Sound, Inc.
• Under license from BBE Sound, Inc.

ACCESSORIES LIST

REF. NO PART NO. KANRI DESCRIPTION

NO.
1 8A-NFJ-937-010 IB,EZ(9L)E 46(RDS)<A>
TYPE MODEL NAME SUFFIX
1 8A-NFJ-936-010 IB,EZ(9L)E 44/DR6<B>
1 8A-NFJ-926-010 IB,EZ(9L)M 44<C> A NOT USED
1 8A-NFJ-927-010 IB,EZ(9L)M 46(RDS)<D> B CX-NDR6 EZ
1 8A-NFJ-904-010 IB,G(E)M<E> C CX-NBL44 EZ
D CX-NBL46 EZ
1 8A-NFJ-925-010 IB,K(E)M 44<F>
2 8Z-NF8-702-010 RC UNIT,RC-ZAS01 E CX-NBL44 G
3 87-006-225-010 ANT,LOOP ANT NC2 F CX-NBL44 K
4 87-A90-118-010 ANT,WIRE FM(Z)

2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the CAUTION
instructions below when servicing. Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
WARNING! radiation exposure.
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO ATTENTION
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE L'utilisation de commandes, réglages ou procédures autres que
FROM A DISTANCE OF MORE THAN 30cm FROM THE ceux spécifiés peut entraîner une dangereuse exposition aux
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL radiations.
PICK-UP BLOCK.
ADVARSEL!
Caution: Invisible laser radiation when
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
open and interlocks defeated avoid expo-
af funktion. Undgå udsættelse for stråling.
sure to beam.
Advarsel:Usynling laserståling ved åbning,
This Compact Disc player is classified as a CLASS 1 LASER
når sikkerhedsafbrydere er ude af funktion.
product.
Undgå udsættelse for stråling.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit-
ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit- CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
tävälle näkymättömälle lasersäteilylle. LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT

VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling ZA3/ZA4 MODEL
laserstrålning, som överskrider gränsen för laserklass 1.

Precaution to replace Optical block

Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.

1) After the connection, remove solder shown in

the figure below.

ZA8/ZD8 MODEL

Solder

3
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure
MAIN C.B
1 Remove the AC power cord.
2 Connect a discharging resistor at an end of lead wire that D101
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3 Contact the other end of the discharging resistor to the 3 4
positive (+) side (+VH) of C101. (For two seconds) C101 C102
4 Contact the same end of the discharging resistor as step 3
to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope. 2 2

Select a discharging resistor referring to the following table.

Charging voltage (V) Discharging
Rated power (W) Parts number
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.

4
 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.

R
TE
FRONT C.B
PU
M
CO
RO

18 15 VSS
IC

15
M

C113 MICRO-
COMPUTER
18 VDD
C113
FRONT C.B
Short with tweezers.

Fig-2-2

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

5
ELECTRICAL MAIN PARTS LIST

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
IC C0018 87-012-368-080 C-CAP,S 0.1-50 Z F
C0019 87-016-520-000 CAP,E 3300-65 M SMG
87-020-454-010 IC,DN6851 C0020 87-016-520-000 CAP,E 3300-65 M SMG
87-A21-355-010 IC,STK490-140 C0023 87-016-658-000 CAP,E 4700-35 M SMG
8A-NF8-620-010 C-IC,LC866548V-5R49<B,C,E,F> C0024 87-016-658-000 CAP,E 4700-35 M SMG
8A-NF8-621-010 C-IC,LC866560W-5R50<A,D>
87-A21-629-010 IC,SPS-442-1-N C0025 87-010-408-080 CAP,E 47-50 M 11L SME
C0026 87-010-247-080 CAP,E 100-50 M SME
87-A21-419-040 C-IC,NJM14558MD-TE2 C0030 87-010-430-080 CAP,E 100-63
87-A21-577-040 C-IC,M61506FP C0031 87-010-263-080 CAP,E 100-10 M 11L SME
87-070-289-040 C-IC,BU2092F C0032 87-010-197-080 C-CAP,S 0.01-25 K B C2012
87-A21-401-040 C-IC,M61503FP
87-A21-560-010 IC,LA1844L-A C0034 87-010-260-080 CAP,E 47-25 M 11L SME
C0035 87-010-380-080 CAP,E 47-16 M 11L SME
87-A20-440-040 C-IC,BU1920FS<A,D> C0036 87-010-381-080 CAP,E 330-16 M SME
87-070-127-110 IC,LC72131D C0038 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0060 87-010-403-080 CAP,E 3.3-50 M 11L SME
TRANSISTOR C0061 87-010-260-080 CAP,E 47-25 M 11L SME
C0101 87-010-183-080 C-CAP,S 2700P-50 K B GRM
87-026-609-080 TR,KTA1266GR C0102 87-010-183-080 C-CAP,S 2700P-50 K B GRM
89-213-702-010 TR,2SB1370E C0103 87-010-545-080 CAP,E 0.22-50 M 11L SME
87-026-610-080 TR,KTC3198GR C0104 87-010-545-080 CAP,E 0.22-50 M 11L SME
87-A30-076-080 C-TR,2SC3052F
87-A30-075-080 C-TR,2SA1235F C0107 87-010-405-080 CAP,E 10-50 M 11L SME
C0108 87-010-405-080 CAP,E 10-50 M 11L SME
87-026-245-080 TR,DTC114ES C0109 87-010-179-080 C-CAP,S 1200P-50 K B GRM
87-A30-198-080 TR,KTC3199GR C0110 87-010-179-080 C-CAP,S 1200P-50 K B GRM
87-A30-107-070 C-TR,CMBT5401 C0111 87-010-405-080 CAP,E 10-50 M 11L SME
87-A30-106-040 C-TR,CMBT5551
87-A30-087-080 C-FET,2SK2158 C0112 87-010-405-080 CAP,E 10-50 M 11L SME
C0113 87-A12-180-080 CAP,E 10-63 M 105 KME
87-A30-074-080 C-TR,RT1P 141C C0114 87-A12-180-080 CAP,E 10-63 M 105 KME
87-A30-318-080 TR,CSA952K<F> C0119 87-010-197-080 C-CAP,S 0.01-25 K B C2012
87-A30-495-080 TR,2SA1981Y<EXCEPT F> C0120 87-010-197-080 C-CAP,S 0.01-25 K B C2012
87-A30-091-080 FET,2SJ460
87-A30-329-080 TR,CD1585BC C0123 87-010-176-080 C-CAP,S 680P-50 J SL
C0124 87-010-176-080 C-CAP,S 680P-50 J SL
87-A30-090-080 FET,2SK2541 C0125 87-012-368-080 C-CAP,S 0.1-50 Z F
87-A30-104-080 C-TR,RT1N 441C C0126 87-012-368-080 C-CAP,S 0.1-50 Z F
87-A30-468-080 C-TR,KRC102S-RTK C0127 87-012-368-080 C-CAP,S 0.1-50 Z F
87-A30-484-080 C-TR,KRA102S
87-A30-492-080 TR,2SC5343G<EXCEPT F> C0128 87-012-368-080 C-CAP,S 0.1-50 Z F
C0129 87-010-191-080 C-CAP,S 0.015-50 Z F GRM
89-333-317-880 TR,2SC3331(T/U)<F> C0130 87-010-191-080 C-CAP,S 0.015-50 Z F GRM
89-327-143-080 C-TR,2SC2714O C0131 87-010-197-080 C-CAP,S 0.01-25 K B C2012
87-A30-489-080 C-TR,KRA107S C0132 87-010-197-080 C-CAP,S 0.01-25 K B C2012
87-A30-086-040 C-TR,CSD1306E
89-503-602-080 C-FET,2SK360E C0133 87-010-186-080 C-CAP,S 4700P-50 K B C2012
C0134 87-010-379-080 CAP,E 22-16 M 11L SME
87-A30-234-080 TR,CSC4115BC C0140 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0141 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0237 87-010-322-080 C-CAP,S 100P-50 J CH GRM
DIODE
C0238 87-010-322-080 C-CAP,S 100P-50 J CH GRM
87-A40-393-090 DIODE,1N5402GW(F20) C0270 87-010-197-080 C-CAP,S 0.01-25 K B C2012<EXCEPT F>
87-020-465-080 DIODE,1SS133 C0301 87-010-178-080 C-CAP,S 1000P-50 K B C2012
87-A40-547-090 DIODE,D5SBA20 C0302 87-010-178-080 C-CAP,S 1000P-50 K B C2012
87-A40-553-080 DIODE,1N4003 LES C0303 87-010-179-080 C-CAP,S 1200P-50 K B GRM
87-A40-776-080 ZENER,UZ27BSD
C0304 87-010-179-080 C-CAP,S 1200P-50 K B GRM
87-A40-764-080 ZENER,UZ10BSC C0307 87-010-263-080 CAP,E 100-10 M 11L SME
87-A40-270-080 C-DIODE,MC2838 C0308 87-010-263-080 CAP,E 100-10 M 11L SME
87-A40-313-080 C-DIODE,MC2840 C0309 87-010-318-080 C-CAP,S 47P-50 J CH GRM
87-A40-269-080 C-DIODE,MC2836 C0310 87-010-318-080 C-CAP,S 47P-50 J CH GRM
87-A40-768-080 ZENER,UZ16BSA
C0313 87-010-188-080 C-CAP,S 6800P-50 K B C2012
87-A40-752-080 ZENER,UZ6.2BSC C0314 87-010-188-080 C-CAP,S 6800P-50 K B C2012
87-A40-802-080 ZENER,UZ5.1BSC C0315 87-010-263-080 CAP,E 100-10 M 11L SME
87-A40-739-080 ZENER,UZ2.7BSA C0317 87-010-546-080 CAP,E 0.33-50 M 11L SME
87-017-149-080 ZENER,HZS6A2L C0318 87-010-546-080 CAP,E 0.33-50 M 11L SME

C0326 87-010-198-080 C-CAP,S 0.022-25 K B C2012

MAIN C.B C0327 87-012-368-080 C-CAP,S 0.1-50 Z F
C0360 87-010-401-080 CAP,E 1-50 M 11L SME
C0003 87-012-368-080 C-CAP,S 0.1-50 Z F C0365 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0004 87-012-368-080 C-CAP,S 0.1-50 Z F C0399 87-012-140-080 C-CAP,S 470P-50 J CH
C0005 87-012-368-080 C-CAP,S 0.1-50 Z F
C0006 87-012-368-080 C-CAP,S 0.1-50 Z F C0401 87-010-544-080 CAP,E 0.1-50 M 11L SME
C0015 87-012-368-080 C-CAP,S 0.1-50 Z F C0402 87-010-544-080 CAP,E 0.1-50 M 11L SME
C0403 87-010-321-080 C-CAP,S 82P-50 J CH
C0016 87-012-368-080 C-CAP,S 0.1-50 Z F C0404 87-010-321-080 C-CAP,S 82P-50 J CH
C0017 87-012-368-080 C-CAP,S 0.1-50 Z F C0405 87-010-197-080 C-CAP,S 0.01-25 K B C2012

6
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
C0406 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0807 87-010-400-080 CAP,E 0.47-50 M 11L SME
C0407 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0808 87-010-401-080 CAP,E 1-50 M 11L SME
C0408 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0809 87-010-401-080 CAP,E 1-50 M 11L SME
C0409 87-010-182-080 C-CAP,S 2200P-50 K B C2012 C0810 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0410 87-010-182-080 C-CAP,S 2200P-50 K B C2012 C0814 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0411 87-010-405-080 CAP,E 10-50 M 11L SME C0815 87-010-400-080 CAP,E 0.47-50 M 11L SME
C0412 87-010-405-080 CAP,E 10-50 M 11L SME C0816 87-010-400-080 CAP,E 0.47-50 M 11L SME
C0452 87-010-382-080 CAP,E 22-25 M 11L SME C0818 87-010-180-080 C-CAP,S 1500P-50 K B C2012
C0453 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0821 87-010-405-080 CAP,E 10-50 M 11L SME
C0454 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0823 87-012-349-080 C-CAP,S 1000P-50 J CH GRM

C0455 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0824 87-010-404-080 CAP,E 4.7-50 M 11L SME
C0456 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0825 87-010-596-080 C-CAP,S 0.047-16 K R C2012
C0457 87-A12-361-080 CAP,M 5600P-100 J CP<EXCEPT F> C0831 87-010-406-080 CAP,E 22-50 M 11L SME
C0458 87-010-178-080 C-CAP,S 1000P-50 K B C2012 C0842 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0459 87-010-175-080 C-CAP,S 560P-50 J SL C0844 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0460 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0850 87-010-260-080 CAP,E 47-25 M 11L SME
C0461 87-012-158-080 C-CAP,S 390P-50 J CH GRM C0851 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0462 87-012-158-080 C-CAP,S 390P-50 J CH GRM C0852 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0521 87-010-546-080 CAP,E 0.33-50 M 11L SME C0853 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0522 87-010-546-080 CAP,E 0.33-50 M 11L SME C0858 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

C0605 87-010-184-080 C-CAP,S 3300P-50 K B C2012 C0859 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0606 87-010-184-080 C-CAP,S 3300P-50 K B C2012 C0860 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0609 87-010-213-080 C-CAP,S 0.015-25 K B GRM C0869 87-010-197-080 C-CAP,S 0.01-25 K B C2012<A,D>
C0610 87-010-213-080 C-CAP,S 0.015-25 K B GRM C0870 87-018-131-080 CAP,TC U 1000P-50 K B UP050<A,D>
C0611 87-010-545-080 CAP,E 0.22-50 M 11L SME C0871 87-012-156-080 C-CAP,S 220P-50 J CH GRM<A,D>

C0612 87-010-545-080 CAP,E 0.22-50 M 11L SME C0872 87-012-156-080 C-CAP,S 220P-50 J CH GRM<A,D>
C0613 87-010-545-080 CAP,E 0.22-50 M 11L SME C0873 87-012-140-080 C-CAP,S 470P-50 J CH<A,D>
C0614 87-010-545-080 CAP,E 0.22-50 M 11L SME C0874 87-010-405-080 CAP,E 10-50 M 11L SME<A,D>
C0615 87-010-154-080 C-CAP,S 10P-50 D CH GRM C0875 87-010-196-080 C-CAP,S 0.1-25 Z F C2012<A,D>
C0616 87-010-385-080 CAP,E 220-25 M SME C0876 87-010-405-080 CAP,E 10-50 M 11L SME<A,D>

C0617 87-010-385-080 CAP,E 220-25 M SME C0877 87-010-197-080 C-CAP,S 0.01-25 K B C2012<A,D>
C0618 87-010-405-080 CAP,E 10-50 M 11L SME C0878 87-010-316-080 C-CAP,S 33P-50 J CH GRM<A,D>
C0620 87-010-263-080 CAP,E 100-10 M 11L SME C0879 87-010-314-080 C-CAP,S 22P-50 J CH GRM<A,D>
C0630 87-016-669-080 C-CAP,S 0.1-25 K B C0940 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0631 87-010-185-080 C-CAP,S 3900P-50 K B C0942 87-010-149-080 C-CAP,S 5P-50 C CH GRM

C0632 87-010-185-080 C-CAP,S 3900P-50 K B C0947 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0633 87-016-369-080 C-CAP,S 0.033-25 K B GRM C0948 87-012-140-080 C-CAP,S 470P-50 J CH
C0634 87-016-369-080 C-CAP,S 0.033-25 K B GRM C0952 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0661 87-012-157-080 C-CAP,S 330P-50 J CH GRM C0957 87-010-311-080 C-CAP,S 12P-50 J CH GRM
C0662 87-012-157-080 C-CAP,S 330P-50 J CH GRM C0958 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0669 87-010-180-080 C-CAP,S 1500P-50 K B C2012 C0959 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0670 87-010-180-080 C-CAP,S 1500P-50 K B C2012 C0960 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0677 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0962 87-010-401-080 CAP,E 1-50 M 11L SME
C0771 87-010-263-080 CAP,E 100-10 M 11L SME C0963 87-015-785-080 C-CAP, 0.1-25 Z F C3216
C0772 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0971 87-010-381-080 CAP,E 330-16 M SME

C0779 87-010-186-080 C-CAP,S 4700P-50 K B C2012 C0972 87-010-404-080 CAP,E 4.7-50 M 11L SME
C0780 87-010-186-080 C-CAP,S 4700P-50 K B C2012 C0973 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0782 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0974 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0783 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0979 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0784 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0981 87-010-260-080 CAP,E 47-25 M 11L SME

C0785 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0982 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0786 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0983 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0788 87-010-149-080 C-CAP,S 5P-50 C CH GRM C0984 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0789 87-A10-801-080 C-CAP,S 0.022-16 J B CM C0985 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0790 87-A10-801-080 C-CAP,S 0.022-16 J B CM C0987 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0791 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0989 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0792 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0991 87-010-312-080 C-CAP,S 15P-50 J CH GRM
C0793 87-010-404-080 CAP,E 4.7-50 M 11L SME C0992 87-010-312-080 C-CAP,S 15P-50 J CH GRM
C0794 87-012-140-080 C-CAP,S 470P-50 J CH<B,C,E,F> C0993 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0794 87-012-155-080 C-CAP,S 180P-50 J CH GRM<A,D> C0995 87-010-178-080 C-CAP,S 1000P-50 K B C2012

C0795 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0997 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0796 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0998 87-010-260-080 CAP,E 47-25 M 11L SME
C0797 87-010-405-080 CAP,E 10-50 M 11L SME C0999 87-A11-132-080 CAP,TC U 0.01-50 K B
C0798 87-010-197-080 C-CAP,S 0.01-25 K B C2012 CF0831 87-008-423-010 FLTR,CF SFE10.7MS3G-A
C0799 87-010-407-080 CAP,E 33-50 M 11L SME CF0832 82-785-747-010 CF,MS2 GHY,R

C0800 87-012-369-080 C-CAP,S 0.047-50 Z F CN0301 87-A60-620-010 CONN,3P V 2MM JMT

C0801 87-010-403-080 CAP,E 3.3-50 M 11L SME CN0351 87-A60-625-010 CONN,8P V 2MM JMT
C0802 87-010-194-080 C-CAP,S 0.047-25 Z F CN0601 87-099-719-010 CONN,30P H BLK TYK-B(X)
C0803 87-010-198-080 C-CAP,S 0.022-25 K B C2012 CN0602 87-A60-131-010 CONN,6P V FE
C0804 87-010-263-080 CAP,E 100-10 M 11L SME CNA0001 8A-NF8-654-010 CONN ASSY,11P TID-A(480)

7
 REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
FB0602 87-008-372-080 FLTR,EMI BL01 RN1 C0325 87-A10-189-040 CAP,E 220-10 M 5L
FFC0602 88-906-251-110 FF-CABLE,6P 1.25 C0326 87-A10-189-040 CAP,E 220-10 M 5L
FFE0831 A8-6ZA-191-130 6ZA-1 FEENM<C,D,E,F> C0332 87-010-178-080 C-CAP,S 1000P-50 K B C2012
FFE0831 A8-6ZA-19C-170 6ZA-1 YFEENC<A,B> C0334 87-010-312-080 C-CAP,S 15P-50 J CH GRM
J0201 87-A60-488-010 JACK,DIA6.3 BLK ST W/SW KM16AT C0335 87-012-140-080 C-CAP,S 470P-50 J CH

J0203 87-A60-238-010 TERMINAL,SP 4P (MSC) C0336 87-012-155-080 C-CAP,S 180P-50 J CH GRM

J0204 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN C0339 87-012-156-080 C-CAP,S 220P-50 J CH GRM
J0602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN C0340 87-010-197-080 C-CAP,S 0.01-25 K B C2012
J0832 87-A60-403-010 TERMINAL,ANT PAL 2P HSP-312V05 C0341 87-010-194-080 C-CAP,S 0.047-25 Z F
JW0105 87-A00-764-010 RES,M/F 0.22-3W J C0351 87-010-981-040 CAP,E 22-35 M 5L SRE

JW0106 87-A00-764-010 RES,M/F 0.22-3W J C0401 87-010-197-080 C-CAP,S 0.01-25 K B C2012

L0101 87-A50-610-010 COIL,1UH K(MDEC) C0451 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
L0102 87-A50-610-010 COIL,1UH K(MDEC) C0452 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
L0451 87-007-342-010 COIL,OSC 85KHZ BIAS C0453 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
L0801 87-A50-608-010 COIL,FM DET-N(TOK) C0454 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

L0802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK) C0455 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

L0811 87-005-847-080 COIL,2.2UH K CECS C0458 87-010-320-080 C-CAP,S 68P-50 J CH GRM
L0832 87-005-847-080 COIL,2.2UH K CECS C0459 87-010-320-080 C-CAP,S 68P-50 J CH GRM
L0861 87-005-847-080 COIL,2.2UH K CECS<A,D> C0602 87-010-322-080 C-CAP,S 100P-50 J CH GRM
L0941 87-A50-020-010 COIL,ANT LW (COI) 252KHZ C0603 87-010-322-080 C-CAP,S 100P-50 J CH GRM

L0942 87-A50-019-010 COIL,OSC LW (COI) 856KHZ C0604 87-010-322-080 C-CAP,S 100P-50 J CH GRM
L0951 8A-NF8-668-010 COIL,AM PACK 2(TOK) C0650 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
R0129 87-A00-764-010 RES,M/F 0.22-3W J C0699 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
R0130 87-A00-764-010 RES,M/F 0.22-3W J CN0101 87-099-720-010 CONN,30P BLK TYK-B(P)
R0143 87-A00-439-050 RES,180-1/2W J RP CN0102 87-099-015-010 CONN,13P V BLK 6216

R0144 87-A00-439-050 RES,180-1/2W J RP CN0302 87-A60-136-010 CONN,11P V FE

R0145 87-A00-439-050 RES,180-1/2W J RP FB0301 87-008-372-080 FLTR,EMI BL01 RN1
R0146 87-A00-439-050 RES,180-1/2W J RP FFC0102 88-913-301-110 FF-CABLE,13P-1.25
R0790 87-010-197-080 C-CAP,S 0.01-25 K B C2012 FFC0105 88-911-101-110 FF-CABLE,11P 1.25
R0991 87-010-322-080 C-CAP,S 100P-50 J CH GRM FL0401 8A-NF8-601-010 FL,HNA-11MM30(ANF-8)

R0993 87-010-322-080 C-CAP,S 100P-50 J CH GRM L0331 87-A50-408-010 COIL,OSC 5.76MHZ

R0995 87-010-322-080 C-CAP,S 100P-50 J CH GRM LED0311 87-A40-589-040 LED,SLR-56VCT31 RED
SFR0451 87-A90-432-080 SFR,30K H NVZ6TLTA LED0601 87-A40-803-010 LED,SELU1E10CXM-S LF38 BLUE
SFR0452 87-A90-432-080 SFR,30K H NVZ6TLTA LED0602 87-A40-619-080 LED,SLR-56PT-TE7-W GRN
TC0942 87-011-253-080 TRIMMER,CER 30P 4.0X4.5 ECRLA LED0603 87-A40-619-080 LED,SLR-56PT-TE7-W GRN

WH0001 87-A91-179-010 HLDR,WIRE 2.5-11P LED0604 87-A40-619-080 LED,SLR-56PT-TE7-W GRN

X0861 87-A70-091-010 VIB,XTAL 4.332MHZ CSA-309<A,D> LED0606 87-A40-619-080 LED,SLR-56PT-TE7-W GRN
X0991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309 LED0607 87-A40-619-080 LED,SLR-56PT-TE7-W GRN
LED0608 87-A40-619-080 LED,SLR-56PT-TE7-W GRN
S0401 87-A91-024-180 SW,TACT KSHG611BT
FRONT C.B
S0402 87-A91-024-180 SW,TACT KSHG611BT
C0201 87-010-322-080 C-CAP,S 100P-50 J CH GRM S0403 87-A91-024-180 SW,TACT KSHG611BT
C0202 87-010-322-080 C-CAP,S 100P-50 J CH GRM S0404 87-A91-024-180 SW,TACT KSHG611BT
C0203 87-010-322-080 C-CAP,S 100P-50 J CH GRM S0405 87-A91-024-180 SW,TACT KSHG611BT
C0204 87-010-322-080 C-CAP,S 100P-50 J CH GRM S0406 87-A91-024-180 SW,TACT KSHG611BT
C0205 87-010-322-080 C-CAP,S 100P-50 J CH GRM
S0407 87-A91-024-180 SW,TACT KSHG611BT
C0206 87-010-322-080 C-CAP,S 100P-50 J CH GRM S0408 87-A91-024-180 SW,TACT KSHG611BT
C0207 87-010-322-080 C-CAP,S 100P-50 J CH GRM S0409 87-A91-024-180 SW,TACT KSHG611BT
C0208 87-010-322-080 C-CAP,S 100P-50 J CH GRM S0410 87-A91-024-180 SW,TACT KSHG611BT
C0209 87-010-322-080 C-CAP,S 100P-50 J CH GRM S0411 87-A91-024-180 SW,TACT KSHG611BT
C0210 87-010-322-080 C-CAP,S 100P-50 J CH GRM
S0412 87-A91-024-180 SW,TACT KSHG611BT<A,D>
C0211 87-010-322-080 C-CAP,S 100P-50 J CH GRM S0413 87-A91-024-180 SW,TACT KSHG611BT
C0251 87-010-405-040 CAP,E 10-50 M 11L SME S0414 87-A91-024-180 SW,TACT KSHG611BT
C0253 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 S0415 87-A91-024-180 SW,TACT KSHG611BT
C0254 87-012-369-080 C-CAP,S 0.047-50 Z F S0416 87-A91-024-180 SW,TACT KSHG611BT
C0255 87-010-560-040 CAP,E 10-50 M 5L MA
S0417 87-A91-024-180 SW,TACT KSHG611BT
C0256 87-010-405-040 CAP,E 10-50 M 11L SME S0418 87-A91-024-180 SW,TACT KSHG611BT
C0259 87-010-405-040 CAP,E 10-50 M 11L SME S0419 87-A91-024-180 SW,TACT KSHG611BT
C0264 87-A11-148-080 CAP,TC U 0.1-50 Z F S0420 87-A91-024-180 SW,TACT KSHG611BT<A,D>
C0273 87-010-178-080 C-CAP,S 1000P-50 K B C2012 S0421 87-A91-024-180 SW,TACT KSHG611BT<A,D>
C0274 87-010-178-080 C-CAP,S 1000P-50 K B C2012
S0425 87-A91-024-180 SW,TACT KSHG611BT
C0301 87-010-182-080 C-CAP,S 2200P-50 K B C2012 S0426 87-A91-024-180 SW,TACT KSHG611BT
C0302 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 S0432 87-A91-024-180 SW,TACT KSHG611BT
C0303 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 S0433 87-A91-024-180 SW,TACT KSHG611BT
C0312 87-010-498-040 CAP,E 10-16 M 5L SRE S0434 87-A91-024-180 SW,TACT KSHG611BT
C0314 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
S0435 87-A91-024-180 SW,TACT KSHG611BT
C0315 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 S0436 87-A91-024-180 SW,TACT KSHG611BT
C0316 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 S0437 87-A91-024-180 SW,TACT KSHG611BT
C0321 87-012-393-080 C-CAP,S 0.22-16 K W5R CM/CB SW0252 87-A91-555-010 SW,RTRY EC12E24504
C0322 87-010-400-040 CAP,E 0.47-50 M 11L SME SW0253 87-A91-542-010 SW,RTRY EC12E12504

8
 REF. NO PART NO. KANRI DESCRIPTION
NO.
DECK C.B

CON105 87-099-753-010 CONN,11P 9604 S F

SFR1 87-024-581-010 SFR,3.3K DIA 6H
SOL1 82-ZM1-618-410 SOL ASSY,27
SOL2 82-ZM1-618-410 SOL ASSY,27
SW1 87-A90-248-010 SW,MICRO ESE11SH2CXQ

SW2 87-A90-248-010 SW,MICRO ESE11SH2CXQ

SW3 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW4 87-036-110-010 SW,MICRO SPPB62
SW5 87-036-110-010 SW,MICRO SPPB62
W1 82-ZM3-601-010 RBN,CORD,4P-75

HEAD-1 C.B

85-ZM3-602-010 PWB,FLEX A
CON301 87-NF6-615-010 CONN ASSY,3P PB

PT C.B

C0001 87-010-387-080 CAP,E 470-25 M SME

C0002 87-A11-148-080 CAP,TC U 0.1-50 Z F
C0031 87-010-403-040 CAP,E 3.3-50 M 11L SME
CN0001 87-A61-122-010 CONN,11P V TID-A
!PT0001 8A-NFJ-608-010 PT,ANF-8 EZ(2)

!PT0002 8A-NF8-662-010 PT,SUB ANF-8 (E)

!RY0002 87-A91-418-010 RELAY,AC12V G5PA-1-M
!T0001 87-A60-317-010 TERMINAL, 1P MSC
!T0002 87-A60-317-010 TERMINAL, 1P MSC

TYPE MODEL NAME SUFFIX

A NOT USED
B CX-NDR6 EZ
C CX-NBL44 EZ
D CX-NBL46 EZ
E CX-NBL44 G
F CX-NBL44 K

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
Dimensions (mm) :A
Wattage Type Tolerance Symbol Form L W t Resistor Code : A
1/16W 1005 5% CJ 1.0 0.5 0.35 104
L
1/16W 1608 5% CJ t 1.6 0.8 0.45 108
1/10W 2125 5% CJ W 2 1.25 0.45 118
1/8W 3216 5% CJ 3.2 1.6 0.55 128

9
TRANSISTOR ILLUSTRATION

B
E

ECB BCE SDG ECB 2SA1235

2SC2714
DTC114ES 2SB1370 2SJ460 2SA1981 2SC3052
KTC3199 2SK2541 2SC3331 CMBT5401
2SC5343 CMBT5551
CD1585 CSD1306
CSA952 KRA102S
CSC4115 KRA107S
KTA1266 KRC102S
D S KTC3198 RT1N441C
RT1P141C

G D
S G

2SK2158 2SK360

10
FL (HNA-11MM30) GRID ASSIGNMENT/ANODE CONNECTION

GRID ASSIGNMENT

ANODE CONNECTION

11 12
WIRING-1 (MAIN C.B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14

CN601
D

R622

NOT USED

13 14
SCHEMATIC DIAGRAM-1 (FUNCTION/AMP SECTION)

NOT USED

15 16
SCHEMATIC DIAGRAM-2 (TUNER SECTION)

NOT USED

17 18
SCHEMATIC DIAGRAM-3 (PT SECTION) WIRING-3 (DECK C.B)
1 2 3 4 5 6 7

WIRING-2 (PT C.B)

1 2 3 4 5 6 7
E

A GRN
YEL

GRY
BRN
GRY
G

GRN

WHT
YEL

RED
WHT
BLK
H

EH RPH

DECK 2

PH
DECK 1

19 20
WIRING-4 (FRONT C.B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14

NOT USED

21 22
SCHEMATIC DIAGRAM-4 (FRONT SECTION)

TO CD MECHANISM
NOT USED

23 24
IC BLOCK DIAGRAM
IC, LA1844 IC, M61506FP IC, BU2092F

IC, LC72131D IC, M61503FP

25 26
IC DESCRIPTION
IC, LC866560W-5R50 <46EZ>, LC866548V-5R49 <Except 46EZ>
Pin No. Pin Name I/O Description
_______________
1 I-STEREO/I-DRF I Stereo detected input/CD DRF input
______
2 I-IFC/I-SUBQ I Tune IF count serial data input/CD SUBQ input
3 O-2PB O Deck 2 playback switch output
_______
4 O-POWER O System power supply ON/OFF output
_______
5 O-CD-ON O CD power ON/OFF output
6 O-PLL_DATA O LED driver, Tuner IC, Function IC data output
7 O-RMT O Deck 2 REC MUTE output
_________ _____
8 O-BIAS O Deck 2 bias ON/OFF output
_______
9 O-MUTE O System mute ON/OFF output
10 O-STB O Latch strobe output for LED driver IC
_________________
11 O-CLK_SFT O Micon clock shift output
12 RESET I System reset
13 NC – Not connected
14 I-DISH I CD turntable photo sensor A/D converter input
15 VSS1 – GND
16 CF1 – 5.76 MHz oscillator circuit
17 CF2 – 5.76 MHz oscillator circuit
18 VDD1 – Power supply input
__________
19 I-HOLD I Power failure detected input
20 I-KEY1 I KEY input (A/D)
21 I-KEY2 I KEY input (A/D)
22 I-KEY3 I KEY input (A/D)
23 I-TU_SIG I Tuner signal input
24 I-CDSW I CD mechanical switch A/D converter input
25 I-SPEANA I A/D input for spectrum analyzer display
26 I-RE_VOL I Rotary encoder input (VOL)
27 I-WRQ/I-RDS_CLK I CD WRQ input/Tuner RDS clock input
28 I-TM_BASE I Reference clock input for timer watch
_________
29 I-RMC I System remotecontrol signal input
30 ~ 40 G11 ~ G1 O FL GRID output G11 ~ G1
41 NC – Not connected
42 ~ 45 P35 ~ P32 O FL SEGMENT output P35 ~ P32
46 VDD3 – Power supply input
47 ~ 48 P31 ~ P30 O FL SEGMENT output P31 ~ P30
49 P29/O-SPEANA-C O FL SEGMENT output P29/Spectrum analyzer band switching output
50 P28/O-SPEANA-B O FL SEGMENT output P28/Spectrum analyzer band switching output
51 VFL – Power supply input for FL display
52 P27/O-SPEANA-A O FL SEGMENT output P27/Spectrum analyzer band switch output
53 P26 O FL SEGMENT output P26
54 P25/I-NO_CASINO I/O FL SEGMENT output P25/NO CASINO DEMO input to diode
55 P24/I-KARAOKE I/O FL SEGMENT output P24/KARAOKE input to diode
56 P23/NO_DEMO I/O FL SEGMENT output P23/NO DEMO input to diode

27
Pin No. Pin Name I/O Description

57 P22/PRO LOGIC I/O FL SEGMENT output P22/PROLOGIC input to diode (not used)
58 P21/RDS I/O FL SEGMENT output P21/RDS input to diode
59 P20/FM1 I/O FL SEGMENT output P20/FM1 input to diode
60 P19/SW I/O FL SEGMENT output P19/SW input to diode
61 P18/LW I/O FL SEGMENT output P18/LW input to diode
62 P17/AMST I/O FL SEGMENT output P17/AMST input to diode
63 P16/AM10K I/O FL SEGMENT output P16/AM10K input to diode
_________
64 P15/I-CST2 I/O FL SEGMENT output P15/DECK2 cassette detect switch data input
________
65 P14/I-REB I/O FL SEGMENT output P14/DECK2 side-B record OK switch data input
___________
66 P13/I-CAM2 I/O FL SEGMENT output P13/DECK2 CAM switch signal input
____________
67 P12/I-AUTO1 I/O FL SEGMENT output P12/DECK1 AUTO STOP signal input
_____________
68 P11/I-AUTO2 I/O FL SEGMENT output P11/DECK2 AUTO STOP signal input
__________
69 P10/I-CAM1 I/O FL SEGMENT output P10/DECK1 CAM switch data input
_________
70 P9/I-CST1 I/O FL SEGMENT output P9/DECK1 cassette detect switch data input
________
71 P8/I-REA I/O FL SEGMENT output P8/DECK2 side A record OK switch data input
72 VDD4 – Power supply input
73 P7/I-REV2 I/O FL SEGMENT output P7/DECK2 REVERSE mode input to diode
74 P6/I-REV1 I/O FL SEGMENT output P6/DECK1 REVERSE mode input to diode
75 P5/NO_ECO I/O FL SEGMENT output P5/NO ECO MODE input to diode
76 ~ 79 P4 ~ P1 O FL SEGMENT output P4 ~ P1
80 O-CD CLOSE O CD TRAY CLOSE data output
81 O-CD OPEN O CD TRAY OPEN data output
82 NC – Not connected
83 I-JOG_A I Rotary encoder A input (JOG)
84 I-JOG_B I Rotary encoder B input (JOG)
85 O-DISH_FWD O CD turntable forward rotation output
86 O-DISH_REV O CD turntble reverse rotation output
87 O-PLL_CE O PLL IC chip enable output
_____________
88 O-KSCAN O Switch SCAN timing output
89 VSS2 – GND
90 VDD2 – Power supply input
_________
91 LED-STBY O STAND BY LED (Echo mode) ouput
______________ _____
92 O-MOTOR O DECK MOTOR ON/OFF output
_________
93 O-SOL1 O DECK1 soleroid ouput
_________
94 O-SOL2 O DECK2 soleroid ouput
95 O-CD-DATA O CD DATA output
96 O-CD-LED O CD LED output
97 O-CD CLK O CD clock output
98 O-CD CE O CD chip enable output
99 I-RDS_DATA I RDS data input
100 O-PLL_CLK O PLL IC CLOCK output

28
ADJUSTMENT
< TUNER SECTION > < DECK SECTION >
1. Clock frequency Check 10. Tape Speed Adjustment (DECK 2)
MAIN C.B 9 8 1 9
Settings : • Test point : TP2 Settings : • Test tape : TTA–100
Method : Set to AM 1602kHz and check that the test point is • Test point : TP8(Lch), TP9(Rch)
TC942 2052kHz ± 45Hz. • Adjustment location : SFR1
L802 Method : Play back the test tape and adjust SFR1 so that the
14 L801 L941 2. MW VT Check frequency counter reads 3000Hz ± 5Hz and ±45Hz
IC801 TP4 (DC BALANCE)
6 Settings : • Test point : TP1 (VT) (REV) with respect to forward speed.
SFR451 SFR452
TP3 (DC BALANCE) Method : Set to MW 1602kHz, 531kHz and check that the
L951
TP2 (CLK) test point is less than 8.0V (1602kHz) and more 11. Head Azimuth Adjustment (DECK 1, DECK 2)
5 than 0.6V (531kHz). Settings : • Test tape : TTA–330
L942
TP8 (RCH) (3/3) (1/3) • Test point : TP8(Lch), TP9(Rch)
GND 3
3. LW VT Adjustment • Adjustment location : Head azimuth
TP9 (LCH) TP1 (VT) 2 Settings : • Test point : TP1 (VT) adjustment screw
3 • Adjustment location: L942 Method : Play back (FWD) the 8kHz signal of the test tape
FFE831 4 Method : Set to LW 144kHz and adjust L942 so that the test and adjust screw so that the output becomes
point is 1.3V ± 0.05V. maximum. Next, perform on REV PLAY mode.
5 11 Then set to LW 290kHz and check that the test
6 12 point is less than 8.0V. 12. PB Frequency Response Check (DECK 1, DECK 2)
7 13 Settings : • Test tape : TTA–300
8 14 4. FM VT Check • Test point :TP8(Lch), TP9(Rch)
9 15 Settings : • Test point : TP1 (VT) Method : Play back the 315Hz and 8kHz signals of the test
10 Method : Set to FM 87.5MHz, 108.0MHz and check that the tape and check that the output ratio of the 8kHz
test point is more than 0.5V (87.5MHz) and less signal with respect to that of the 315Hz signal is
than 8.0V (108.0MHz). within 5dB.

5. MW Tracking Adjustment 13. PB Sensitivity Check (DECK 1, DECK 2)

Settings : • Test point : TP8(Lch), TP9(Rch) Settings : • Test tape : TTA–200
DECK-2 R/P HEAD DECK-1 P HEAD • Adjustment location : • Test point : TP8(Lch), TP9(Rch)
DECK C.B L951(1/3) ...................................... 999kHz Method : Play back the test tape and check that the output
Method : Set to MW 999kHz and adjust L951(1/3) so that the level of the test point is 140mV ± 3dB.
SFR1 level at the test point becomes maximum.
14. REC/PB Frequency Response Adjustment (DECK 2)
6. LW Tracking Adjustment Settings : • Test tape : TTA–602
11 10 11 11 Settings : • Test point : TP8(Lch), TP9(Rch) • Test point : TP8(Lch), TP9(Rch)
11
REV FWD • Adjustment location : L941, TC942 • Input signal : 1kHz / 8kHz (LINE IN)
FWD REV
Method : Set up TC942 to center position. • Adjustment location : SFR451 (Lch)
16 Set to LW 144kHz and adjust L941 so that the level SFR452 (Rch)
FRONT C.B at test point becomes maximum. Method : Apply a 1kHz signal and REC mode. Then adjust
Then set to LW 290kHz and adjust TC942 so that OSC attenuator so that the output level at the TP8,
the level at test point becomes maximum. TP9 becomes -20VU. Record and play back the
FL401 TP7 1kHz and 8kHz signals and adjust SFRs so that the
7. FM Tracking Check output of the 8kHz signals becomes 0dB ± 0.5dB
R268

Settings : • Test point : TP8(Lch), TP9(Rch) with respect to that of the 1kHz signal.
C326

Method : Set to FM 98.0MHz and check that the test point is

30
+ less than 13dBµV. 15. REC/PB Sensitivity Check (DECK 2)
IC201
Settings : • Test tape : TTA–602
L331
GND 1 8. AM IF Adjustment • Test point : TP8(Lch), TP9(Rch)
Settings : • Test point : TP8(Lch), TP9(Rch) • Input signal : 1kHz (LINE IN)
• Adjustment location : Method : Apply a 1kHz signal and REC mode. Then adjust
16 L802 ............................................. 999kHz OSC attenuator so that the output level at TP8, TP9
becomes 0VU. Record and play back the 1kHz
9. DC Balance / Mono Distortion Adjustment signals and check that the output is –2dB ± 3.0dB.
Settings : • Test point : TP3, TP4 (DC Balance)
: TP8(Lch), TP9(Rch) (Distortion) < FRONT SECTION >
• Adjustment location : L801 16. µ-CON OSC Adjustment
• Input level : 60dBµV Settings : • Test point : TP7 and GND
Method : Set to FM 98.0MHz and adjust L801 so that the • Adjustment location : L331
voltage between TP3 and TP4 becomes 0V ± 0.3V. Method : Insert AC plug while pressing POWER and TUNER
Next, check that the distortion is less than 1.3%. function keys. Adjust L331 so that the frequency
atthe test point is 153.84Hz ± 0.15Hz.

29 30
MECHANICAL EXPLODED VIEW 1/1

38
A
A AZG-1
A
39

17
A 18 P.C.B 37
16
47

A
A A
B
F
A 41
14 WIRE,BINDER
15 HT-SINK
FL401 19 40 F
22 36

13 A P.C.B
20 B C
21

27 A
12
26 G
24 A
23 A
H 25 A

A G
42
9 29 P.C.B
28 HT-SINK FIN1
HT-SINK FIN2
E 30
31 I A
5 H 44
8
43
3
11 32
9 A
A

33 A
6 34
45
1 7
10 CHAS,MAIN
D

6ZM-3 46
PLATE,EARTH MECH 34 33 35
F
2 4

31 32
MECHANICAL MAIN PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
1 8A-NFJ-012-010 WINDOW,CASS 1 30 8A-NFJ-031-010 KEY,CD EDIT E<A,D>
2 8A-NFJ-013-010 WINDOW,CASS 2 30 8A-NFJ-025-010 KEY,CD EDIT U<B,C,E,F>
3 8A-NFJ-035-010 BOX,CASS 1H 31 8A-NFJ-027-010 KEY,DISC
4 8A-NFJ-003-010 BOX,CASS 2 U 32 87-NF4-216-010 HLDR,LOCK 1
5 8A-NF8-207-010 SPR-T,EJECT 1 33 86-NF9-224-010 SPR-C,LOCK

6 8A-NF8-208-010 SPR-T,EJECT 2 34 82-NF5-229-010 PLATE,LOCK(*)

7 8A-NFJ-005-010 WINDOW,FR 2 35 87-NF4-217-110 HLDR,LOCK 2
8 8A-NFJ-017-010 KNOB,RTRY JOG<F> 36 8A-NF8-206-010 HLDR,PWB M
8 8A-NFJ-017-110 KNOB,RTRY JOG<C,D,E> 37 87-064-185-010 HLDR,WIRE PVC 0.5
8 8A-NFJ-017-210 KNOB,RTRY JOG<A,B> 38 84-ZG1-245-210 CAP,OPTICAL

9 8A-NF8-209-010 OIL-DMPR,120 39 8A-NFJ-056-010 CABI,REAR 44 EZSM<C>

10 8A-NFJ-070-010 CABI,FR E44<F> 39 8A-NFJ-076-010 CABI,REAR 44 G W/O SPEC<E>
10 8A-NFJ-070-110 CABI,FR E44<B,C,E> 39 8A-NFJ-058-010 CABI,REAR 44 KSM<F>
10 8A-NFJ-069-110 CABI,FR E46<A,D> 39 8A-NFJ-075-010 CABI,REAR 46 EZSE<A>
11 8A-NFJ-004-010 WINDOW,FR 1 39 8A-NFJ-057-010 CABI,REAR 46 EZSM R<D>

12 8A-NFJ-071-010 WINDOW,DISP DR6<B> 39 8A-NFJ-074-010 CABI,REAR DR6 EZSE<B>

12 8A-NFJ-047-010 WINDOW,DISP E44<C,E,F> 40 8A-DB8-209-010 HLDR,PWB PT
12 8A-NFJ-048-010 WINDOW,DISP E46<A,D> 41 8A-NF8-205-010 HLDR,IC
13 8A-NFJ-008-010 WINDOW,CD 42 87-NF4-221-010 HLDR,CABLE
14 8A-NF8-007-010 PANEL,LEFT V-2 ! 43 87-085-185-010 BUSHING,AC CORD(E) CM-22B

15 8A-NF8-005-010 PANEL,TOP ! 44 87-A80-157-010 AC CORD ASSY,E BLK CC<EXCEPT E>

16 8A-NF8-006-010 WINDOW,TOP ! 44 87-050-081-110 AC CORD ASSY,G<E>
17 8A-NFJ-009-010 PANEL,TRAY 45 8Z-NB8-240-010 COVER, PL
18 8A-NFJ-010-010 WINDOW,TRAY 46 8A-NF8-008-010 PANEL,RIGHT V-2
19 88-NF8-205-010 GUIDE,FL 47 88-906-251-110 FF-CABLE,6P 1.25

20 8A-NFJ-018-010 KEY,FUN A 87-067-703-010 BVT2+3-10 W/0 SL0T

21 8A-NFJ-016-010 REFLECTOR,FUN B 87-NF4-224-010 S-SCREW,IT3B+3-8 CU
22 8A-NFJ-014-010 KEY,POWER C 87-067-581-010 BVT2+3-15 W/0 SL0T
23 8A-NFJ-015-010 REFLECTOR,ECO D 87-067-688-010 BVTT+3-6
24 8A-NFJ-019-010 KEY,GEQ E 87-723-096-410 QT2+3-10 W/O SLOT BLK

25 8A-NFJ-029-010 KEY,ASSY OPE REV F 87-067-641-010 UTT2+3-8 W/O SLOT BLK

26 8A-NF8-203-010 GUIDE,OPE REV G 87-078-191-010 S-SCREW,IT+4-10 SWCH12A
27 8A-NF8-201-010 GUIDE,FUN H 87-721-097-410 QT2+3-12 W/O SLOT
28 88-911-101-110 FF-CABLE,11P 1.25 I 87-721-096-410 QT2+3-10 W/O SLOT
29 88-913-301-110 FF-CABLE,13P-1.25

TYPE MODEL NAME SUFFIX

A NOT USED
B CX-NDR6 EZ
C CX-NBL44 EZ
D CX-NBL46 EZ
E CX-NBL44 G
F CX-NBL44 K

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink

33
MECHANISM MAIN PARTS LIST 1/1 <6ZM-3 PR2NM (44/46), 6ZM-3 YPR2N (DR6)>

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
1 86-ZM3-215-010 1E CHAS ASSY,RS 41 82-ZM1-216-310 0E GEAR,REEL
2 86-ZM3-202-010 0E BASE,HEAD S 42 86-ZM3-213-010 0E S-SCREW,HLDR,MOT 3
3 86-ZM3-205-010 0E SPR-C,RPH S 43 82-ZM1-225-210 0E GEAR,FR
4 82-ZM1-333-210 0E PLATE,LINK 2 44 82-ZM1-226-010 0E GEAR,REW
5 86-ZM3-206-010 0E SPR-C,EH S 45 82-ZM3-333-310 1B SLIP DISK ASSY 2

6 87-A90-403-010 1B HEAD,RPH MS15R 46 82-ZM1-338-010 0E BELT FR4

7 86-ZM3-201-010 1A CHAS,HEAD S(DECK L) 47 82-ZM1-237-610 1A FLY-WHL ASSY,RW
7 82-ZM3-206-210 1A BELT,R 47 09-001-420-010 1A FLY-WHL ASSY,R3W
8 87-045-347-010 1H MOT,SHU2L 70(M1) 48 82-ZM1-259-210 0E SPR-T,PINCH R
9 82-ZM1-269-210 0E SPR-T,BRG 49 82-ZM1-341-110 1A LVR ASSY,PINCH L2

10 82-ZM1-219-110 0E SPR-T,LINK 50 82-ZM1-258-210 0E SPR-T,PINCH L

11 86-ZM3-209-010 0E S-SCREW,ASIMUTHS 51 82-ZM1-314-110 0E PLATE,HEAD
12 86-ZM3-207-010 0E S-SCREW,RPH 52 82-ZM1-208-310 0E HLDR,HEAD
13 87-A90-404-010 0E HEAD,EH LE15B 53 87-A90-366-010 1D HEAD,PH YK50P-BF414
14 86-ZM3-208-010 0E S-SCREW,EH 54 82-ZM1-207-810 0E GUIDE TAPE

15 86-ZM3-203-010 1B HLDR,MOTS 55 82-ZM1-213-010 0E SPR-T,HEAD

16 82-ZM1-245-210 0E HLDR,IC 56 82-ZM1-210-110 0E GEAR,HT
17 82-ZM1-218-010 0E SPR-E,HB 57 86-ZM4-206-010 0E S-SCREW AZIMUTH L
18 86-ZM3-214-010 0E BELT,SUB RR 58 82-ZM1-234-310 1A FLY-WHL,L ASSY
19 82-ZM1-222-210 0E LVR,PLAY 59 82-ZM3-339-010 0E SHAFT,COUPLER N3

20 82-ZM1-217-410 0E REEL TABLE 60 82-ZM3-335-210 0E PULLEY,COUPLER M3

21 82-ZM1-244-510 0E SPR-C,BT 61 86-ZM1-206-010 0E BELT,MAIN L
22 82-ZM1-285-410 0E SPR-C,BT L 62 82-ZM1-266-110 0E LVR,DIR
23 82-ZM1-257-010 0E SPR-T,CAS 63 82-ZM1-214-010 0E SPR-T,DIR
24 82-ZM3-221-010 0E PULLEY,MOT 2M A 87-251-071-410 0E U+2.6-4

25 82-ZM1-242-010 0E LVR,CAS B 80-ZM6-243-010 0E SH,1.75-3.6-0.5 SLT

26 82-ZM1-243-010 0E LVR,STOP C 82-ZM3-334-010 0E PW,2.16-6-0.4
27 82-ZM1-344-110 1A LVR ASSY,PINCH D 80-ZM6-207-010 0E V+1.6-7
28 86-ZM3-204-010 0E SPR-T,PINCHDS E 85-ZM3-202-010 0E S-SCREW TG
29 82-ZM1-240-110 0E LVR,REC (DECK 2) F 82-ZM1-288-010 0E SH,1.63-3.2-0.5 SLT

30 86-ZM3-210-010 0E BELT,RS G 87-B10-043-010 0E W-P,0.99-4-0.25 SLT

32 82-ZM3-305-110 0E GEAR,CAM M2 H 87-571-032-410 0E VIT+2-3
33 82-ZM1-227-310 0E LVR,TRIG
34 82-ZM3-306-110 0E LVR,FR M2
35 82-ZM1-265-110 0E SPR-E,TRIG

36 87-761-073-410 0E VFT2+2.6-6 W/O SLOT

37 82-ZM1-255-310 0E SPR-E,LVR DIR
38 82-ZM1-322-010 0E SPR-T,FR60
39 82-ZM1-220-210 0E GEAR,IDLER
40 82-ZM3-616-010 0E RING MAGNET 4

34
MECHANISM EXPLODED VIEW 1/1 <6ZM-3 PR2NM (44/46), 6ZM-3 YPR2N (DR6)>

57 14
D 11
12
51
D
5 12 8
53 3
E
13 SOL 2 DECK C.B
52
(DECK L
only) 6

55
54 15
2 16
17
SOL 1

56 A D
16
44
10 A
A
9 41
G
24 61
7 60
(DECK L SIDE)
18
43
63
62 (DECK R SIDE)
30 35
LEVER
EJECT R C
19 41
47 E

49
45
33

HEAD 27 A H
20
C.B 50 59 PLATE
4 CAPSTAN N 2.2-41.7 34
SHLD M3

32
48
22
LEVER EJECT L F
46
58
21 40
C D

29 39

(DECK 2) 25
CAPSTAN N 2-41.5
27
A
26 C
23 38

B
37
A 28 B

F E
1

36
B
42
F

35 36
SPEAKER DISASSEMBLY INSTRUCTIONS
SPEAKER (SX-NBL40) <44EZ, 44K, NDR6EZ> PARTS LIST
Type.1 Type.4

Insert a flat-bladed screwdriver into the position indicated by the TOOLS

arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
unit and then remove the speaker units. NO. NO.
2 ( – ) flat head screwdriver
1 8A-NSX-001-010 PANEL,FR 11 8A-NSX-602-010 SPKR, W 140
3 Cut chisel 2 8A-NSX-014-010 PANEL,BA L 12 8A-NSK-604-010 SPKR,TW 60
3 8A-NSX-015-010 PANEL,BA R 13 87-NSH-612-010 SPKR,CERAMIC ASSY
4 8A-NSX-016-010 PANEL,DUCT
5 8A-NSX-003-010 GRILLE,FRAME ASSY

6 8A-NSX-010-010 PANEL,TW R
7 8A-NSX-011-010 PANEL,TW L
8 8A-NSX-012-010 PROTECTOR, TW R
9 8A-NSX-013-010 PROTECTOR, TW L
10 87-NS7-611-010 CORD,SPKR

1 2 3

How to Remove the PANEL, FR SPEAKER (SX-NBL42) <46EZ> PARTS LIST

Type.2 1. Insert the ( – ) flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
Remove the grill frame and four pieces of rubber caps by pulling head of the ( – ) flat head screwdriver with the plastic
out with a flat-bladed screwdriver. Remove the screws from hole hammer head, and create the clearance as shown in Fig-1. REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
where installed rubber caps. Insert a flat-bladed screwdriver into NO. NO.
the position indicated by the arrows and remove the panel. Re- 2. Insert the cut chisel in the clearance, and tap the head of 1 8A-NSX-001-010 PANEL,FR 12 8A-NSK-604-010 SPKR,TW 60
move the screws of each speaker unit and then remove the 2 8A-NSX-014-010 PANEL,BA L 13 87-NSH-612-010 SPKR,CERAMIC ASSY
the cut chisel with plastic hammer as shown in Fig-2, to 3 8A-NSX-015-010 PANEL,BA R
speaker units. remove the PANEL, FR. 4 8A-NSX-016-010 PANEL,DUCT
6 8A-NSX-010-010 PANEL,TW R
3. Place the speaker horizontally. Tap head of the cut chisel 7 8A-NSX-011-010 PANEL,TW L
with plastic hammer as shown in Fig-3, and remove the 8 8A-NSX-012-010 PROTECTOR, TW R
PANEL, FR completely. 9 8A-NSX-013-010 PROTECTOR, TW L
10 87-NS7-611-010 CORD,SPKR
11 8A-NSX-602-010 SPKR, W 140

SPEAKER (SX-NSZ53) <44G> PARTS LIST

Type.3 REF. NO PART NO. KANRI DESCRIPTION

NO.
Insert a flat-bladed screwdriver into the position indicated by the 1 8A-NSJ-001-010 PANEL,FR R
2 8A-NSJ-002-010 PANEL,FR L
arrows and remove the panel. Turn the speaker unit to counter- 3 8A-NSJ-008-010 PROTECTOR,TWA
clockwisedirection while inserting a flat-bladed screwdriver into 4 8A-NSJ-024-010 GRILLE,FRAME ASSY L
one of the hollows around speaker unit, and then remove the 5 8A-NSJ-004-010 GRILLE,FRAME
speaker unit. After replacing the speaker unit, install it turning to Fig-1 Fig-2 6 8A-NSJ-006-010 BADGE,AIWA S35
clockwise direction until "click" sound comes out. 7 87-NS7-611-010 CORD,SPKR
8 88-MS1-608-010 SPKR, CERAMIC
9 8A-NSX-602-010 SPKR, W 140
10 8A-NSK-604-010 SPKR,TW 60

Fig-3

How to Attach the PANEL, FR

Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.

37 38
 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
920074 Printed in Singapore