Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc,

Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Overview

KEMET’s 900 Series encapsulated radial through-hole ceramic With a working voltage of 440 VAC in line-to-line (Class X) and
disc capacitors are specifically designed for interference- 300 VAC in line-to-ground (Class Y) applications, these safety
suppression AC line filtering applications. Having internationally capacitors meet the impulse test criteria outlined in IEC Standard
recognized safety certifications, these capacitors are well-suited 60384. Meeting subclass X1 and Y2 requirements, these devices
for applications that require keeping potentially disruptive or are certified to withstand impulses up to 4 KV (X1) and 5 KV (Y2)
damaging line transients and EMI out of susceptible equipment. respectively. These encapsulated devices also meet the flame test
They are also an ideal solution in situations where there is a requirements outlined in UL Standard 94V–0.
need to suppress line disturbances at the source.

Safety Certified Capacitors are classified as either X and/or

Y capacitors. Class X capacitors are primarily used in line-to-
line (across-the-line) applications. In this application there is
no danger of electric shock to humans should the capacitor
fail, but could result in a risk of fire. The class Y capacitor is
primarily used in line-to-ground (line by-pass) applications. In
this application, failure of the capacitor could lead to danger of
electric shock.

Ordering Information

C9 7 1 U 472 M Z W D A A 7317
Ceramic Body Lead Capacitance Capacitance Rated Dielectric/ Lead Failure Packaging
Spec. Design
Series Diameter Spacing1,3 Code (pF) Tolerance Voltage Temp. Char. Config.2,3 Rate (C-Spec)2,3
C9 = 0 = 7.0 mm 7 = 7.5 mm U= 2 significant C = ±0.25 pF Z = X1 N = CH D= A= A= 7317 = Ammo Pack
Ceramic 1 = 8.0 mm 1 = 10.0 mm Safety digits + D = ±0.5 pF 440 VAC (NP0) Disc Straight N/A WL30 = Bulk/3.0 mm
900 2 = 9.0 mm Number of J = ±5% / Y2 300 S = SL B = Vertical Lead length
Series 3 = 10.0 mm zeroes K = ±10% VAC Y = Y5P Kink WL35 = Bulk/3.5 mm
4 = 11.0 mm Use 9 for M = ±20% W = Y5U C= Lead length
6 = 13.0 mm 1.0 - V = Y5V Outside WL40 = Bulk/4.0 mm
8 = 15.0 mm 9.9 pF Kink Lead length
e.g., 2.2 pF D = Inside WL45 = Bulk/4.5 mm
= 229 Kink Lead length
WL50 = Bulk/5.0 mm
Lead length
WL20 = Bulk/20 mm
Lead length
1
Capacitor body diameter will limit available lead spacing and packaging options. See "Dimensions" and "Product Ordering Codes and Ratings" sections of this
document to determine availability.
2
"Vertical Kink","Outside Kink" and "Inside Kink" lead configurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead length is
only available on capacitors with straight leads (lead configuration ordering code "A"). For nonstandard lead length inquiries, please contact KEMET.
3
Bulk packaging lead length availability is dependent upon "Lead Configuration" and "Lead Spacing." See "Dimensions" section of this document to verify
availability of a specific lead length option. For nonstandard lead length inquiries, please contact KEMET.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 1
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Lead Configurations

Straight Vertical Kink Outside Kink Inside Kink

Dimensions – Millimeters

Lead F L Packaging D T e Ød
Lead
Lead Config. Packaging C-Spec
Lead Spacing Lead Body Body Lead Lead
Config. Ordering Type2 Ordering
2 Tolerance
Code 1 Spacing Length Code 3 Diameter 2
Thickness Meniscus Dia.
Ammo Pack 20.0 +1.5/-1.0 7317
3.0 ±1.0 WL30
7.5 ±1.0
Bulk 4.5 ±1.0 WL45

5.0 ±1.0 WL50 See Table 1 - "Product

3.0
Straight A Ordering Codes and 0.5 ±0.1
Ammo Pack 20.0 +1.5/-1.0 7317 maximum
Ratings"
3.0 ±1.0 WL30
10.0 ±1.0
Bulk 4.5 ±1.0 WL45

5.0 ±1.0 WL50

Ammo Pack 18.0 +2.0/-0 7317

7.5 ±1.0 3.5 ±1.0 WL35

Bulk
4.0 ±1.0 WL40 See Table 1 - "Product
Vertical Kink 3.0
B Ordering Codes and 0.5 ±0.1
(Preformed) Ammo Pack 18.0 +2.0/-0 7317 maximum
Ratings"
10.0 ±1.0 3.5 ±1.0 WL35
Bulk
4.0 ±1.0 WL40

1
Lead Configuration is identified in the 13th character of the ordering code. See "Lead Configuration" and "Ordering Information" sections of this document for
further details.
2
Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for
further details.
3
The "Packaging C-Spec" is a 4-digit numeric or alphanumeric code which identifies both the packaging type and lead length requirement. When ordering, this
code must be included in the 15th through 18th character positions of the ordering code. See "Ordering Information" section of this document for further details.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 2
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Dimensions – Millimeters cont'd

Lead F L Packaging D T e Ød
Lead
Lead Config. Packaging C-Spec
Lead Spacing Lead Body Body Lead Lead
Config. Ordering Type2 Ordering
2 Tolerance
Code 1 Spacing Length Code 3 Diameter 2
Thickness Meniscus Dia.
Ammo Pack 18.0 +2.0/-0 7317

3.5 ±1.0 WL35

7.5 ±1.0
Bulk 4.0 ±1.0 WL40

5.0 ±1.0 WL50 See Table 1 - "Product

Outside Kink 3.0
C Ordering Codes and 0.5 ±0.1
(Preformed) Ammo Pack 18.0 +2.0/-0 7317 maximum
Ratings"
3.5 ±1.0 WL35
10.0 ±1.0
Bulk 4.0 ±1.0 WL40

5.0 ±1.0 WL50

Ammo Pack 18.0 +2.0/-0 7317

7.5
Inside Kink Bulk 3.5 ±1.0 WL35 13.0 7.0 3.0
D ±1.0 0.5 ±0.1
(Preformed) Ammo Pack 18.0 +2.0/-0 7317 maximum maximum maximum
10.0
Bulk 3.5 ±1.0 WL35

1
Lead Configuration is identified in the 13th character of the ordering code. See "Lead Configuration" and "Ordering Information" sections of this document for
further details.
2
Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for
further details.
3
The "Packaging C-Spec" is a 4-digit numeric or alphanumeric code which identifies both the packaging type and lead length requirement. When ordering, this
code must be included in the 15th through 18th character positions of the ordering code. See "Ordering Information" section of this document for further details.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 3
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Benefits
• Safety Standard Recognized (IEC 60384-14)
• Reliable operation up to 125°C
• Class X1/Y2
• 7.5 mm and 10 mm lead spacing
• Lead (Pb)-free and RoHS Compliant
• Halogen Free
• Capacitance offerings ranging from 2.0 pF up to 10,000 pF
• Available capacitance tolerances of ±0.25 pF, ±0.5 pF, ±5%, ±10%, and ±20%
• High reliability
• Preformed (crimped) or straight lead configurations
• Non-polar device, minimizing installation concerns
• Encapsulation meets flammability standard UL 94V–0

Applications
Typical applications include:
• Line-to-line (Class X) filtering
• Line-to-ground (Class Y) filtering
• Antenna coupling
• Primary and secondary coupling (switching power supplies)
• Line disturbances suppression (motors and motor controls, relays, switching power supplies, and inverters)

Approval Standard and Certification No.

Safety Standard Standard No. Subclass Working Voltage Certificate No.
VDE X1 440 VAC
(ENEC) IEC 60384–14 40036415
Y2 300 VAC

These devices are VDE/ENEC recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per IEC60384–14.

Environmental Compliance
These devices are Halogen Free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS directives.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 4
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

General Specifications/Performance Characteristics

Dielectric/Temperature Characteristic: CH(NP0) SL Y5P Y5U Y5V

Operating Temperature Range -40°C to +125°C
-1,000 ~ +350
Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC) ±60 ppm/ºC ±10% +20%/-55% ~ +30%/-80%
ppm/ºC
2,600 VAC
Dielectric Withstanding Voltage (7.5 mm and 10 mm Lead Spacing) (60 ±5 seconds at 25ºC)
30 pF% and above: ≥ 1,000
Quality Factor (Q) See “Dissipation Factor”
Below 30 pF: ≥ 400 +(20 x C)*
Dissipation Factor (tanδ) at +25ºC1 See “Quality Factor” 2.50% 2.50% 5.0%

10,000 MΩ Minimum
Insulation Resistance (IR) Limit at +25°C (500 VDC applied for 60 ±5 seconds @ 25°C)

*C = Nominal capacitance
2
Capacitance and Dissipation Factor (DF) measured under the following conditions:
CH(NP0) & SL: 1 MHz ± 100 kHz and 1.0 ±0.2 Vrms
X5P, Y5U and Y5V: 1 kHz ± 50 Hz and 1.0 ±0.2 Vrms
Note: When measuring capacitance, it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as
Automatic Level Control (ALC). The ALC feature should be switched to "ON."

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 5
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 1 – Product Ordering Codes and Ratings

Dimensions (mm) Lead Spacing
Dielectric/
KEMET Capacitance Body Body
Temp. Capacitance Lead Bulk Ammo
Part Number Tolerance Diameter Thickness
Char. Diameter Packaging Packaging
(Maximum) (Maximum)
C90(1)U209CZND(2)A(3) 2.0 pF
C90(1)U309CZND(2)A(3) 3.0 pF
±0.25 pF
C90(1)U409CZND(2)A(3) 4.0 pF
C90(1)U509CZND(2)A(3) 5.0 pF
C90(1)U609DZND(2)A(3) 6.0 pF
C90(1)U709DZND(2)A(3) 7.0 pF 7.0
C90(1)U809DZND(2)A(3) 8.0 pF ±0.5 pF
C90(1)U909DZND(2)A(3) 9.0 pF
C90(1)U100DZND(2)A(3) 10 pF
C90(1)U120JZND(2)A(3) 12 pF 7.5 mm
CH
C90(1)U150JZND(2)A(3) 15 pF 5.0 0.5 ±0.1 or
(NP0)
C91(1)U180JZND(2)A(3) 18 pF 10 mm
C91(1)U200JZND(2)A(3) 20 pF
8.0
C91(1)U220JZND(2)A(3) 22 pF
C91(1)U240JZND(2)A(3) 24 pF
±5%
C92(1)U270JZND(2)A(3) 27 pF
C92(1)U300JZND(2)A(3) 30 pF 9.0
C92(1)U330JZND(2)A(3) 33 pF
C93(1)U360JZND(2)A(3) 36 pF
10.0
C93(1)U390JZND(2)A(3) 39 pF
C94(1)U470JZND(2)A(3) 47 pF 11.0

C90(1)U100JZSD(2)A(3) 10 pF
C90(1)U120JZSD(2)A(3) 12 pF
C90(1)U150JZSD(2)A(3) 15 pF
C90(1)U180JZSD(2)A(3) 18 pF
C90(1)U200JZSD(2)A(3) 20 pF
C90(1)U220JZSD(2)A(3) 22 pF
C90(1)U240JZSD(2)A(3) 24 pF
C90(1)U270JZSD(2)A(3) 27 pF 7.0
C90(1)U300JZSD(2)A(3) 30 pF
C90(1)U330JZSD(2)A(3) 33 pF 7.5 mm
SL C90(1)U360JZSD(2)A(3) 36 pF ±5% 5.0 0.5 ±0.1 or
C90(1)U390JZSD(2)A(3) 39 pF 10 mm
C90(1)U470JZSD(2)A(3) 47 pF
C90(1)U500JZSD(2)A(3) 50 pF
C90(1)U510JZSD(2)A(3) 51 pF
C91(1)U560JZSD(2)A(3) 56 pF
C91(1)U620JZSD(2)A(3) 62 pF
8.0
C91(1)U680JZSD(2)A(3) 68 pF
C91(1)U750JZSD(2)A(3) 75 pF
C92(1)U820JZSD(2)A(3) 82 pF 9.0
C93(1)U101JZSD(2)A(3) 100 pF 10.0

Capacitance Body Diameter Body Thickness

KEMET Part Number Capacitance Lead Diameter Lead Spacing
Tolerance (Maximum) (Maximum)

(1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging
options may limit lead spacing availability. See table above to verify availability.)
7 = 7.5 mm
1 = 10.0 mm
(2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this
document, page 2, for further details.)
A = Straight
B = Vertical Kink
C = Outside Kink
D = Inside Kink
(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this
document, page 2, for available options.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 6
Roll Over for
Order Info.
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 1 – Product Ordering Codes and Ratings cont'd

Dimensions (mm) Lead Spacing
Dielectric/
KEMET Capacitance Body Body
Temp. Capacitance Lead Bulk Ammo
Part Number Tolerance Diameter Thickness
Char. Diameter Packaging Packaging
(Maximum) (Maximum)
C90(1)U101KZYD(2)A(3) 100 pF
C90(1)U151KZYD(2)A(3) 150 pF
C90(1)U221KZYD(2)A(3) 220 pF 7.0
C90(1)U331KZYD(2)A(3) 330 pF 7.5 mm
Y5P C90(1)U471KZYD(2)A(3) 470 pF ±10% 5.0 0.5 ±0.1 or
C91(1)U561KZYD(2)A(3) 560 pF 10 mm
8.0
C91(1)U681KZYD(2)A(3) 680 pF
C92(1)U821KZYD(2)A(3) 820 pF
9.0
C92(1)U102KZYD(2)A(3) 1,000 pF

C90(1)U102MZWD(2)A(3) 1,000 pF 7.0

C92(1)U152MZWD(2)A(3) 1,500 pF
9.0 7.5 mm or 10 mm
C92(1)U222MZWD(2)A(3) 2,200 pF
Y5U ±20% 5.0 0.5 ±0.1 7.5 mm or 10 mm
C94(1)U332MZWD(2)A(3) 3,300 pF 11.0
C96(1)U392MZWD(2)A(3) 3,900 pF
13.0 10 mm only
C96(1)U472MZWD(2)A(3) 4,700 pF

C90(1)U102MZVD(2)A(3) 1,000 pF
C90(1)U152MZVD(2)A(3) 1,500 pF 7.0
C90(1)U222MZVD(2)A(3) 2,200 pF
7.5 mm or 10 mm
C92(1)U332MZVD(2)A(3) 3,300 pF 9.0
Y5V ±20% 5.0 0.5 ±0.1 7.5 mm or 10 mm
C94(1)U392MZVD(2)A(3) 3,900 pF
11.0
C94(1)U472MZVD(2)A(3) 4,700 pF
C96(1)U682MZVD(2)A(3) 6,800 pF 13.0
10 mm only
C98(1)U103MZVD(2)A(3) 10,000 pF 15.0

Capacitance Body Diameter Body Thickness

KEMET Part Number Capacitance Lead Diameter Lead Spacing
Tolerance (Maximum) (Maximum)

(1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging
options may limit lead spacing availability. See table above to verify availability.)
7 = 7.5 mm
1 = 10.0 mm
(2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this
document, page 2, for further details.)
A = Straight
B = Vertical Kink
C = Outside Kink
D = Inside Kink
(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this
document, page 2, for available options.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 7
Roll Over for
Order Info.
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions

Item Specification Test Method

Operating Temperature Range -40ºC to +125ºC
Between lead The capacitor shall not be damaged when 2,600 VAC(rms) is applied
No failures
wires between the lead wires for 60 seconds.
The terminals (leads) of the capacitor shall
be connected together. A metal foil is tightly
Dielectric wrapped around the body of the capacitor at a
Strength distance of about 3 to 4 mm from each terminal.
Body Insulation No failures The capacitor is then inserted into a container
filled with metal balls approximately 1 mm in
diameter. 2,600 VAC(rms) is applied for 60
seconds between the capacitor lead wires and
metal balls.
The insulation resistance shall be measured with 500 ±50 VDC applied
Insulation Resistance (IR) 10,000 MΩ minimum after 60 ±5 seconds of charging.
Capacitance Within specified tolerance

Temperature
Specification
Characteristics
Y5P, Y5U DF ≤ 2.5% Y5P, Y5U and Y5V: Capacitance is measured at 1 kHz ±20% and 5
Vrms or less. (20 ±2°C)
Y5V DF ≤ 5.0% NP0 and SL: Capacitance is measured at 1 MHz ±20% and 1.0 ±0.2
Dissipation Factor (DF) or Q Vrms (25°C)
NP0,SL ≥ 30 pF: Q ≥ 1000
< 30 pF: Q ≥ 400
+(20 x C)
C = Nominal
capacitance
A capacitance measurement is made at each step specified:
Temperature Capacitance Step Temperature
Characteristics Change
1 +20 ±2ºC
Y5P Within ±10% 2 -25 ±2ºC
Temperature Characteristics Y5U Within +20%/-55% 3 +20 ±2ºC
Y5V Within ~+30%/-80% 4 +85 ±2ºC
CH 0 ±60 ppm/ºC 5 +20 ±2ºC
SL -1,000 ~+350 ppmºC Pre-treatment:
(+20ºC ~+85ºC) Capacitor is stored at 85 ±2ºC for 1 hour and then placed at room
condition1 for 24 ±2 hours before measurement.
With the termination in its normal position, the specimen is held by its
body in such a manner that the axis of the termination is vertical; a
Tensile Lead wire or capacitor body shall not break. tensile force of 10 N is applied to the termination in the direction of its
axis and acting in a direction away from the body of the specimen.
With the termination in its normal position, the specimen is held by its
Terminal Strength body in such a manner that the axis of the termination is vertical; a
mass force of 5 N is then suspended from the end of the termination.
The body of the specimen is then inclined within a period of 2 to 3
Bending Lead wire or capacitor body shall not break. seconds, through an angle of approximately 90° in the vertical plane
and then resumed to its initial position over the same period of time;
this operation constitutes one bend. One bend immediately followed by
a second bend in the opposite direction.
Lead wire should have a uniform coating of The lead wire of the capacitor is dipped into molten solder for 2 ±0.5
seconds. The depth of immersion is up to 1.5 mm (+5/-0 mm) from the
Solderability solder in the axial direction and over 3/4 of its root of lead wires.
circumference. Solder Temperature: Lead free solder (Sn-3Ag – 0.5Cu) 245°C ±5°C.

1
“Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 8
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item Specification Test Method

Appearance No visual defect As shown in the figure below, the lead wires are immersed in molten
solder up to 1.5 mm (+5/-0 mm) from the end of the epoxy meniscus
(root of lead wire).
IR 1,000 MΩ Duration/Solder Temperature: 3.5 ±0.5 seconds/350°C ±10°C or 10 ±1
Dielectric seconds/260°C ±5°C
Per item 1
Strength
Soldering Effect
(Non-Preheat)
Y5P, Y5U and Y5V: Within ±10%
Capacitance SL, CH (NP0): Within ±2.5% or ±0.25 pF,
whichever is larger. Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then
placed at room condition1 for 24 ±2 hours before initial measurements.
Post-treatment: Capacitor is stored for 1 to 2 hours at room
condition1.
Appearance No visual defect Capacitor is stored at 120°C +0/-5°C for 60 +0/-5 seconds. Then, as
shown in the figure below, the lead wires are immersed in molten solder
IR 1,000 MΩ up to 1.5 mm (+5/-0mm) from the end of the epoxy meniscus (root of
Dielectric lead wire).
Per item 1 Duration/Solder Temperature: 7.5 +0/-1 seconds/260°C ±5°C
Strength
Soldering Effect
(Preheat)
Y5P, Y5U and Y5V: Within ±10%
Capacitance SL, CH (NP0): Within ±2.5% or ±0.25 pF,
whichever is larger.
Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then
placed at room condition1 for 24 ±2 hours before initial measurements.
Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1.

Appearance No visual defect Steady State Humidity: Load Humidity:

Temperature Capacitance
Characteristics Change
Y5P Within ±10%

Capacitance Y5U Within ±20%

Y5V Within ±30%
SL CH (NP0) Within ±2.5% or 90 to 95% humidity at 40°C 90 to 95% humidity at 40°C
±0.25 pF, whichever ±2°C for 500 ±12 hours. ±2°C for 500 ±12 hours with full
Biased Humidity rated voltage applied.
is larger.
Post Treatment:
Capacitor is stored for 1 to 2 Post Treatment:
Y5P and Y5U: 5.0% maximum Capacitor is stored for 1 to 2
DF hours at room condition1.
Y5V: 7.5% maximum hours at room condition1.
SL and CH(NP0): Less than 30 pF:
Q ≥ 100 + 10 × C/3
Q
More than 30 pF: Q ≥ 200
C = Nominal capacitance
Y5P, Y5V and Y5U: 3,000 MΩ minimum
IR
SL and CH (NP0): 1,000 MΩ minimum
Dielectric
No failures
Strength
1
“Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 9
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item Specification Test Method

Appearance No visual defect Impulse Voltage: Each individual capacitor is subjected to three 5 kv
impulses prior to life testing.
Y5P, Y5V and Y5U: Within ±20%
Capacitance
SL and CH (NP0): Within ±3 or ±0.3 pF, Vp UPR Cx tr td
Change (uF) (uS) (uS)
whichever is larger. 0.9Vp

Voltage
UPP 0.01 1.2 46
3,000 MΩ minimum 0.1 1.5 47
IR
SL and CH (NPO): 1,000 MΩ minimum 0.5Vp
High Temperature
Life

Dielectric
Time
tr
No failures td
Strength
Capacitors are placed in a circulating air oven for a period of 1,000
hours. The air in the oven is maintained at a temperature of 125°C ±2
throughout the test. The capacitors are subjected to AC 510 Vrms.
Each hour the voltage is increased to 1,000 Vrms for 0.1 seconds.
The capacitor is exposed to a flame for 15 seconds and then removed
for 15 seconds. This test is repeated for 5 cycles.

The capacitor flame extinguishes as follows:

Flame Test Cycle Time

1~4 30 seconds maximum
5 60 seconds maximum

The capacitors are individually wrapped in at least one, but not more
than two, complete layers of cheesecloth. They are then subjected
to 20 discharges. The interval between successive discharges is 5
seconds. The VAC is maintained for 2 minutes after the last discharge.

C1, 2 1 μF ±10% C3 0.033 μF ±5% 10 kV

Active Flammability The cheesecloth should not ignite. L1-4 1.5 Mh ±20% 16A Rod core choke Cx Test capacitor
R 100 ±2% VAC VR ±5%
Ct 3 μF ±5% 10 kV VR Rated Voltage
F Fuse, Rated 10A Vt Voltage applied to Ct

1
“Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 10
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item Specification Test Method

The capacitor under test is held into a flame and in a position which
best promotes burning. Each specimen is exposed to the flame one
time.

The burning time should not exceed 30

Passive Flammability seconds.
The tissue paper should not ignite.
Time of exposure to flame: 30 seconds
Length of flame: 12 ±1 mm
Gas burner length: 35 mm minimum
Inside diameter: 0.5 ±0.1 mm
Outside diameter: 0.9 mm maximum
Gas butane gas purity: 95% minimum
Appearance No visual defect

Temperature Capacitance
The capacitor is subjected to 5 temperature cycles.
Characteristics Change
Capacitance SL, CH (NP0) Within ±5% (Temperature Cycle)
Y5P Within ±10%
Time
Step Temperature (°C)
Y5U, Y5V Within ±20% (minutes)
1 -40 +0/-3 30
Temperature SL, CH (NP0) ≥ 30 pF: Q ≥ 350
Cycle < 30 pF: Q ≥ 275 2 Room temperature 3
+5/2C 3 125 +3/-0 30
C = Nominal
DF/Q capacitance 4 Room temperature 3

Y5P DF ≤ 5%
Pre-treatment: Capacitor shall be stored at 85 ±2 for 1 hour then
Y5U, Y5V DF ≤ 7.5% placed at room condition1 for 24 ±2 hours.
Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1.
IR 3,000 MΩ minimum
Dielectric
No failures
Strength
1
“Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 11
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Soldering and Mounting Information

Soldering:
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this
product to excessive heating could reflow the solder joint between the lead and ceramic element and/or may result in thermal shocks
that can crack the ceramic element.

When soldering these capacitors with a soldering iron, it should be performed under the following conditions:
• Temperature of iron-tip: 400ºC maximum
• Soldering iron wattage: 50 W maximum
• Soldering time: 3.5 seconds maximum

Cleaning (ultrasonic cleaning):

To perform ultrasonic cleaning, observe the following conditions:
• Rinse bath capacity: Output of 20 watts per liter or less
• Rinsing time: 5 minute maximum
• Do not vibrate the PCB/PWB directly
• Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires

Construction

Reference Item Material

1 Encapsulation1 Epoxy resin, Pigment (Blue/UL 94 V–0)

2 Dielectric Material BaTiO3

3 Solder Sn 96.5, Ag 3, Cu 0.5

4 Electrodes Ag (Glass frit)

Tinned copper clad steel wire
5 Lead Wires
(Sn Plating 100% 3-7 µm)
1
The minimum thickness of the insulation coating (encapsulation) is 0.4 mm
Note: Image is exaggerated in order to clearly identify all components of construction.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 12
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Capacitor Marking
These capacitors shall be stamped or laser marked with KEMET's trademark, type designation, capacitor class, rated voltage, rated
capacitance, and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark and a date/lot
code for traceability. Marking will be supplied either on one side or both sides of the encapsulated capacitor body. All marking shall
be legible to allow for clear identification of the component. Marking appears in legible contrast. Illustrated below is an example of the
marking format and content. (Two sided marking is limited to capacitors with body diameters ≤ 8.0 mm.)

AC472M

X1:440V~ Y2:300V~
2C12345

Location # Description Detail

❶ KEMET Trademark

Type Designation
❷ (2 characters)
AC

First two digits are the significant figures of capacitance. Third digit indicates the additional
Rated Capacitance
❸ (3 numeric characters)
number of zeros. For example, 4,700 pF is identified as 472. (For values below 10 pF an “R” is
used in place of the decimal point, e.g., 2R0 = 2.0 pF.)
Capacitance Tolerance
❹ Code (1 character)
C = 0.25 pF, D = 0.5 pF, J = ±5%, K = ±10%, M = ±20%

VDE & ENEC approval mark

❺ IEC 60384–14 3rd (2005)

Capacitor Class and Rated

❻ Voltage
X1: 440 V ~ Y2: 300 V ~

Date/Lot Code, e.g., 3C12345

3 C 1 2345
Last digit of year, Manufacturing Manufacturing Month: Last 4 digits of
❼ Date/Lot Code e.g., Location Code lot no.
1-9 = Jan - Sept
3 = 2013 A = October
N = November
D = December

Packaging Quantities

Carrier Tape Quantity

Packaging Type Loose (Bulk Bag)
(12.7 mm Pitch ) 1
(15 mm Pitch1) (25.4 mm Pitch1)
Ammo Pack N/A 1,000 pieces/box 500 pieces/box
Bulk 500 pieces/bag N/A
1
For details regarding component pitch on carrier tape, see "Ammo Pack Taping Format" and "Ammo Pack Taping Specifications" sections of this document.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 13
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Figure 1 - Ammo Pack Taping Format

5 mm and 7.5 mm Lead Spacing:

10 mm Lead Spacing:

Table 3 – Ammo Pack Taping Specifications

Lead Spacing 5 mm 7.5 mm 10 mm

Lead Style Straight Preformed1 Straight Preformed1 Straight Preformed1
Item Symbol Dimensions (mm)
Lead Spacing F 5.0 +0.8/-0.2 7.5 ±1.0 10.0 ±1.0
Component Pitch P 12.7 15.0 25.4 ±2
Sprocket Hole Pitch P0 12.7 ±0.3 15.0 ±0.3 12.7 ±0.3
Sprocket Hole Center to
P2 6.35 ±1.5 7.5 ±1.5 12.7 ±1.5
Component Center
Sprocket Hole Center to Lead Center P1 3.75 ±1.0 3.75 ±1.0 7.7 ±1.5
Body Diameter D See "Product Ordering Codes and Ratings" section of this document.
Component Alignment (side/side) ∆S 0 ±2.0
Carrier Tape Width W 18.0 +1.0/-0.5
Sprocket Hole Position W1 9.0 ±0.5
1
Prefromed (crimped) lead configurations include vertical kink, outside kink and inside kink. See "Lead Configurations" and "Ordering Information" sections of this
document for further details.
2
Also referred to as "lead length" in this document.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 14
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 3 – Ammo Pack Taping Specifications cont'd

Lead Spacing 5 mm 7.5 mm 10 mm

Lead Style Straight Preformed1 Straight Preformed1 Straight Preformed1
Item Symbol Dimensions (mm)
Height to Seating Plane 2
H0 N/A 18.0 +2.0/-0 N/A 18.0 +2.0/-0 N/A 18.0 +2.0/-0
(preformed leads1)
Height to Seating Plane2
H 20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A
(straight leads)
Lead Protrusion ℓ 2.0 maximum
Diameter of Sprocket Hole D0 4.0 ±0.2
Lead Diameter φd 0.5 ±0.1
Carrier Tape Thickness t1 0.6 ±0.3
Total Thickness (Carrier Tape,
t2 1.5 maximum
Hold-Down Tape and Lead)
∆h1
Component Alignment (front/back ) 2.0 maximum
∆h2
Cut Out Length L 11.0 maximum
Hold-Down Tape Width W0 11.0 minimum 11.5 minimum
Hold-Down Tape Position W2 3.0 maximum 1.5 ±1.5
1
Prefromed (crimped) lead configurations include vertical kink, outside kink and inside kink. See "Lead Configurations" and "Ordering Information" sections of this
document for further details.
2
Also referred to as "lead length" in this document.

Application Notes:
Storage and Operating Conditions:
The insulating coating of these devices does not form an air and moisture-tight seal. Avoid exposure to moisture and do not use or
store these devices in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt, or the like are present.
Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect product quality and
performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or molded product prior to
implementing and/or qualifying any of these processes. Store the capacitors where the temperature and relative humidity do not
exceed 40 degrees Centigrade and 70% respectively. For optimum solderability, capacitor stock should be used promptly, preferably
within 6 months of receipt.

Working Voltage:
Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated for a
transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a capacitor with a
voltage rating greater than or equal to these irregular voltages.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 15
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Operating Temperature and Self-Generating Heat:

The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be sure to take
into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or similar
current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated heating should not exceed 20°C (while
operated at an atmosphere temperature of 25°C).

Handling - Vibration and Impact:

Do not expose these devices or their leads to excessive shock or vibration during use.

FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR
PARTIAL DISPERSION WHEN THE PRODUCT IS USED.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 16
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

KEMET Corporation Europe Asia

World Headquarters
Southern Europe Northeast Asia
2835 KEMET Way Paris, France Hong Kong
Simpsonville, SC 29681 Tel: 33-1-4646-1006 Tel: 852-2305-1168

Mailing Address: Sasso Marconi, Italy Shenzhen, China

P.O. Box 5928 Tel: 39-051-939111 Tel: 86-755-2518-1306
Greenville, SC 29606
Beijing, China
www.kemet.com Central Europe Tel: 86-10-5829-1711
Tel: 864-963-6300 Landsberg, Germany
Fax: 864-963-6521 Tel: 49-8191-3350800 Shanghai, China
Tel: 86-21-6447-0707
Corporate Offices Kamen, Germany
Fort Lauderdale, FL Tel: 49-2307-438110 Taipei, Taiwan
Tel: 954-766-2800 Tel: 886-2-27528585

Northern Europe
North America
Bishop’s Stortford, United Kingdom Southeast Asia
Tel: 44-1279-460122 Singapore
Southeast
Tel: 65-6586-1900
Lake Mary, FL
Espoo, Finland
Tel: 407-855-8886
Tel: 358-9-5406-5000 Penang, Malaysia
Tel: 60-4-6430200
Northeast
Wilmington, MA
Bangalore, India
Tel: 978-658-1663
Tel: 91-806-53-76817
Central
Novi, MI
Tel: 248-994-1030

West
Milpitas, CA
Tel: 408-433-9950

Mexico
Guadalajara, Jalisco
Tel: 52-33-3123-2141

Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 17
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Other KEMET Resources

Tools
Resource Location
Configure A Part: CapEdge http://capacitoredge.kemet.com
SPICE & FIT Software http://www.kemet.com/spice
Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask
Electrolytic LifeCalculator http://www.kemet.com:8080/elc

Product Information
Resource Location
Products http://www.kemet.com/products
Technical Resources (Including Soldering Techniques) http://www.kemet.com/technicalpapers
RoHS Statement http://www.kemet.com/rohs
Quality Documents http://www.kemet.com/qualitydocuments

Product Request
Resource Location
Sample Request http://www.kemet.com/sample
Engineering Kit Request http://www.kemet.com/kits

Contact
Resource Location
Website www.kemet.com
Contact Us http://www.kemet.com/contact
Investor Relations http://www.kemet.com/ir
Call Us 1-877-MyKEMET
Twitter http://twitter.com/kemetcapacitors

Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are
not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 18
Radial Through-Hole Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1065_X1_440 VAC_Y2_300 VAC • 10/11/2013 19