GRUNDFOS DATA BOOKLET
SP14-15 Rp2 4"3X380-415/50 4.0kW
Grundfos pump 98699358
Thank you for your interest in our products. Please contact us for more information, or visit our website
https://www.lenntech.com/grundfos/SPFAM/98699358/SP-14-15.html
[email protected]
tel. +31 152 610 900
fax. +31 152 616 289
BE > THINK > INNOVATE
Position Qty. Description
1 SP 14-15
Note! Product picture may differ from actual product
Product No.: On request
Submersible borehole pump, suitable for pumping clean water. Can be installed vertically or
horizontally. All steel components are made in stainless steel, EN 1.4301 (AISI 304), that ensures high
corrosive resistance. This pump carries drinking water approval.
The pump is fitted with a 4 kW MS4000 motor with sand shield, mechanical shaft seal, water-lubricated
journal bearings and a volume compensating diaphragm. The motor is a canned type submersible
motor offering good mechanical stability and high efficiency. Suitable for temperatures up to 40 °C.
The motor is not fitted with a temperature sensor. If temperature monitoring is desired, a Pt1000 sensor
can be fitted.
The motor is for direct-on-line starting (DOL).
Further product details
The pump is suitable for applications similar to the following:
- raw-water supply
- irrigation
- groundwater lowering
- pressure boosting
- fountain applications.
The Grundfos SP pump is renowned for its high efficiency and already complies with the requirements
of the Minimum Efficiency Index, and therefore Grundfos is amongst the best in class within
submersible pumps.
Pump
All pump surfaces that are in contact with pumped liquids are made in stainless steel which makes
them corrosion- and wear-resistant. The corrosion diagram below shows the capabilities of the pump
and motor in relation to the temperature in Celsius (y-axis) and the concentration of chloride in ppm
(x-axis).
Printed from Grundfos Product Centre [2018.06.003] 1/10
The elastomer parts in the pump offer good wear resistance and long service intervals. The bearings are made of
LSR (Liquid Silicone Rubber), sealing rings are made of TPU (Thermoplastic Poly-Urethane) and the non-return
valve is made of NBR (Nitrile-Butadiene Rubber). The special elastomer material of the bearings offers increased
resistance to sand and other abrasive particles (from 50 to 150 mg/l).
In case the pump is used for pumping water with high content of hydrocarbons or solvents, Grundfos
offers FKM rubber parts (Fluorocarbon) which are oil and temperature-resistant up to 90 °C.
The pump is built with octagonal bearings with sand flush channels that minimise wear. As wear of the
pump is inevitable, the pump design allows for easy replacement of all internal wear parts (bearings,
impeller, wear rings and seal rings) to maintain high performance and a long lifetime.
The suction interconnector is fitted with a strainer to prevent large particles from entering the pump. The
suction interconnector is designed to comply with NEMA standards for motor mounting/dimensions.
Motor
The stator is hermetically encapsulated in stainless steel and the windings are embedded in polymer
compound. This results in high mechanical stability, optimum cooling and reduces the risk of short
circuits in the windings.
The shaft seal is a tungsten carbide/ceramic replaceable mechanical shaft seal. The material
combination provides optimum sealing, resistance and long life. Together with the shaft seal housing,
the sand shield forms a labyrinth seal, which during normal operating conditions prevents penetration of
sand particles into the shaft seal.
The motor can be fitted with a Pt100 or Pt1000 sensor that together with a control unit ensures that the
maximum operating temperature conditions are not exceeded.
Liquid:
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
Technical:
Rated flow: 14 m³/h
Rated head: 65 m
Shaft seal for motor: HM/CER
Approvals on nameplate: CE,EAC
Curve tolerance: ISO9906:2012 3B
Motor version: T40
Materials:
Pump: Stainless steel
EN 1.4301
AISI 304
Impeller: Stainless steel
EN 1.4301
AISI 304
Motor: Stainless steel
DIN W.-Nr. 1.4301
AISI 304
Installation:
Pump outlet: RP2
Motor diameter: 4 inch
Electrical data:
Motor type: MS4000
Rated power - P2: 4 kW
Power (P2) required by pump: 4 kW
Mains frequency: 50 Hz
Rated voltage: 3 x 380-400-415 V
Rated current: 9.75-9.60-9.80 A
Starting current: 460-500-530 %
Cos phi - power factor: 0.85-0.80-0.77
Rated speed: 2850-2865-2875 rpm
Start. method: direct-on-line
Printed from Grundfos Product Centre [2018.06.003] 2/10
Position Qty. Description
Enclosure class (IEC 34-5): IP68
Insulation class (IEC 85): F
Built-in temp. transmitter: no
Others:
Minimum efficiency index, MEI ≥: 0.50
ErP status: EuP Standalone/Prod.
Net weight: 38 kg
Gross weight: 72.1 kg
Shipping volume: 0.264 m³
Danish VVS No.: 388482015
Printed from Grundfos Product Centre [2018.06.003] 3/10
On request SP 14-15 50 Hz
H SP 14-15, 3*400 V, 50Hz eta
[m] [%]
90
80
70
60
50 100
40 80
30 60
20 40
10 20
0 0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Q [m³/h]
P
[kW]
5.0
4.5
P1
4.0
3.5
P2
3.0
2.5
2.0
1.5
1.0
0.5
Printed from Grundfos Product Centre [2018.06.003] 4/10
H SP 14-15, 3*400 V, 50Hz eta
Description Value [m] [%]
General information:
Product name: SP 14-15
Product No: On request 90
EAN number: On request
80
Technical:
Rated flow: 14 m³/h
70
Rated head: 65 m
Stages: 15 60
Impeller reduc.: NONE
Shaft seal for motor: HM/CER 50 100
Approvals on nameplate: CE,EAC
Curve tolerance: ISO9906:2012 3B 40 80
Model: A
30 60
Valve: YES
Motor version: T40
20 40
Materials:
Pump: Stainless steel 10 20
EN 1.4301
AISI 304 0 0
0 2 4 6 8 10 12 14 16 Q [m³/h]
Impeller: Stainless steel
P
EN 1.4301 [kW]
AISI 304 5
P1
Motor: Stainless steel
4
DIN W.-Nr. 1.4301
AISI 304 3
P2
Installation:
Pump outlet: RP2 2
Motor diameter: 4 inch
Liquid: 95
1
Pumped liquid: Water GN
RP2
101
0
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C RP2
Liquid temperature during operation: 20 °C 101 GN
Density: 998.2 kg/m³
Electrical data:
Motor type: MS4000
Applic. motor: NEMA
Rated power - P2: 4 kW
1363
Power (P2) required by pump: 4 kW
Mains frequency: 50 Hz
1940
Rated voltage: 3 x 380-400-415 V
Rated current: 9.75-9.60-9.80 A
Starting current: 460-500-530 %
Cos phi - power factor: 0.85-0.80-0.77
577
Rated speed: 2850-2865-2875 rpm
Start. method: direct-on-line
Enclosure class (IEC 34-5): IP68 95
Insulation class (IEC 85): F
Motor protec: NONE
L1 L2 L3 PE
Thermal protec: external
Built-in temp. transmitter: no
Motor No: 79194510
Others:
Minimum efficiency index, MEI ≥: 0.50
ErP status: EuP Standalone/Prod.
Net weight: 38 kg
Gross weight: 72.1 kg
Shipping volume: 0.264 m³
Danish VVS No.: 388482015
U V W PE
M
3
Printed from Grundfos Product Centre [2018.06.003] 5/10
On request SP 14-15 50 Hz
cos phi SP14-15 + MS4000 4 kW 3*400 V, 50 Hz I
eta [A]
cos phi
0.8 16
eta
0.6 12
0.4 8
0.2 4
0.0 0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 P2 [kW]
n P1
[rpm] [kW]
n
2800 8
P1
2600 6
2400 4
2200 2
2000 0
Printed from Grundfos Product Centre [2018.06.003] 6/10
On request SP 14-15 50 Hz
RP2
101 GN
1363
1940
577
95
Note! All units are in [mm] unless others are stated.
Disclaimer: This simplified dimensional drawing does not show all details.
Printed from Grundfos Product Centre [2018.06.003] 7/10
Exploded view
251a
251d
77
28
7
7a 17
301a 219
92 301a
11
92
9
51
11b
105
215a
100
215
49
18
66a
45
67
530a
530
215a 217
6
531a
531
534
534a
Printed from Grundfos Product Centre [2018.06.003] 8/10
Sectional drawing (TM058200 for TPE2,TPE3)
3 2 1
TM058200
Printed from Grundfos Product Centre [2018.06.003] 9/10
Exploded view ( TM057026 for MGE model H/I )
251d
251b
291
290
287
277a
287a 273b
293 502
277
252a 286
273a
273
266
275a
268
268a
289a
289
251a 288b
288
288a
252b
159e
150
152
151
157 156
156c
158
185
154
178
172
187
153 191
188
156d
156b
192
156c
159d
Printed from Grundfos Product Centre [2018.06.003] 10/10
Disclaimer: The information about the Grundfos pump in this document may be outdated.
Data may be subject to alterations without further notice.
Please contact us to verify the data above is still accurate/up-to-date.
All information is copyright Grundfos.
[email protected] https://www.lenntech.com
tel. +31 152 610 900
fax. +31 152 616 289
