2005

Powertrain
bY dR.dEaDhEaD
 TABLE OF CONTENTS
1.0 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1.1 SYSTEM COVERAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1.2 SIX-STEP TROUBLE SHOOTING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . .1

2.0 IDENTIFICATION OF SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

3.0 SYSTEM DESCRIPTION AND FUNCTIONAL OPERATION . . . . . . . . . . . . . . . . . . . . . .2

3.1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

3.2 FUNCTION OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3.2.1 FUEL CONTROL (GAS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3.2.2 ON-BOARD DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3.2.3 TRANSMISSION CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3.2.3.1 TRANSMISSION OPERATION AND SHIFT SCHEDULING AT
VARIOUS OIL TEMPERATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3.2.4 O2 SENSOR (NGC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3.2.5 OTHER CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3.2.6 NON-MONITORED CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3.3 DIAGNOSTIC TROUBLE CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3.3.1 HARD CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.3.2 ONE TRIP FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.3.3 INTERMITTENT CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.3.4 STARTS SINCE SET COUNTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.3.5 TROUBLE CODE ERASURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
3.3.6 QUICK LEARN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
3.3.7 EATX DTC EVENT DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.3.8 CLUTCH VOLUMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.3.9 NO START INFORMATION (POWERTRAIN) . . . . . . . . . . . . . . . . . . . .13
3.4 USING THE DRBIIIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.5 DRBIIIT ERROR MESSAGES AND BLANK SCREEN . . . . . . . . . . . . . . . . . . . . .13
3.5.1 DRBIIIT DOES NOT POWER UP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.5.2 DISPLAY IS NOT VISIBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.5.3 SOME DISPLAY ITEMS READ 9___9. . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.6 TRANSMISSION SIMULATOR (MILLER TOOL # 8333) AND ELECTRONIC
TRANSMISSION ADAPTER KIT (MILLER TOOL #8333-1A) . . . . . . . . . . . . . . 14

4.0 DISCLAIMERS, SAFETY, WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

4.1 DISCLAIMERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

4.2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4.2.1 TECHNICIAN SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . .15
4.2.2 VEHICLE PREPARATION FOR TESTING. . . . . . . . . . . . . . . . . . . . . . .15
4.2.3 SEVICING SUB-ASSEMBLIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4.2.4 DRBIIIT SAFETY INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4.3 WARNINGS AND CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
4.3.1 ROAD TEST WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
4.3.2 VEHICLE DAMAGE WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
4.3.3 ROAD TESTING A COMPLAINT VEHCILE (TRANSMISSION) . . . . . .16
4.3.4 ELECTRONIC PINION FACTOR WARNINGS (IF APPLICABLE) . . . .17
4.3.5 SERVICE BULLETINS AND RECALLS . . . . . . . . . . . . . . . . . . . . . . . . .17

5.0 REQUIRED TOOLS AND EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

i
bY dR.dEaDhEaD
 TABLE OF CONTENTS - Continued
6.0 ACRONYMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

6.1 DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

7.0 DIAGNOSTIC INFORMATION AND PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . .21

COMMUNICATION
*NO RESPONSE FROM PCM (PCI BUS) - NGC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
*NO RESPONSE FROM PCM (PCM SCI ONLY) - NGC . . . . . . . . . . . . . . . . . . . . . . . .23
*NO RESPONSE FROM SENTRY KEY IMMOBILIZER MODULE . . . . . . . . . . . . . . . .26
*NO RESPONSE FROM TRANSMISSION CONTROL MODULE - NGC . . . . . . . . . . .28
*PCI BUS COMMUNICATION FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

DRIVEABILITY - NGC
INTERMITTENT CONDITION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT. . . . . . . . . . . . . . . . . . . .35
P0031-O2 SENSOR 1/1 HEATER CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
P0037-O2 SENSOR 1/2 HEATER CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
P0051-O2 SENSOR 2/1 HEATER CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
P0057-O2 SENSOR 2/2 HEATER CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
P0032-O2 SENSOR 1/1 HEATER CIRCUIT HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
P0038-O2 SENSOR 1/2 HEATER CIRCUIT HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
P0052-O2 SENSOR 2/1 HEATER CIRCUIT HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
P0058-O2 SENSOR 2/2 HEATER CIRCUIT HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION - VACUUM
LEAK DETECTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
P2074-MAP SENSOR/TP SENSOR CORRELATION - VACUUM LEAK DETECTED .44
P0071-AMBIENT TEMP SENSOR PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . .50
P0072-AMBIENT TEMP SENSOR CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
P0073-AMBIENT TEMP SENSOR CIRCUIT HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
P0107-MAP SENSOR CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
P0108-MAP SENSOR CIRCUIT HIGH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
P0111-INTAKE AIR TEMPERATURE SENSOR PERFORMANCE . . . . . . . . . . . . . . . . .61
P0112-INTAKE AIR TEMPERATURE SENSOR CIRCUIT LOW . . . . . . . . . . . . . . . . . . .64
P0113-INTAKE AIR TEMPERATURE SENSOR CIRCUIT HIGH . . . . . . . . . . . . . . . . . .66
P0116-ENGINE COOLANT TEMPERATURE CIRCUIT PERFORMANCE. . . . . . . . . . .68
P0117-ENGINE COOLANT TEMPERATURE SENSOR CIRCUIT LOW . . . . . . . . . . . .71
P0118-ENGINE COOLANT TEMPERATURE SENSOR CIRCUIT HIGH . . . . . . . . . . . .73
P0122-THROTTLE POSITION SENSOR NO.1 LOW . . . . . . . . . . . . . . . . . . . . . . . . . . .75
P0123-THROTTLE POSITION SENSOR NO.1 HIGH. . . . . . . . . . . . . . . . . . . . . . . . . . .78
P0125-INSUFFICIENT COOLANT TEMP FOR CLOSED-LOOP FUEL CONTROL . . .81
P0128-THERMOSTAT RATIONALITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
P0129-BAROMETRIC PRESSURE OUT-OF-RANGE . . . . . . . . . . . . . . . . . . . . . . . . . .88
P0131-O2 SENSOR 1/1 CIRCUIT LOW VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
P0137-O2 SENSOR 1/2 CIRCUIT LOW VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
P0151-O2 SENSOR 2/1 CIRCUIT LOW VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
P0157-O2 SENSOR 2/2 CIRCUIT LOW VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
P0132-O2 SENSOR 1/1 CIRCUIT HIGH VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
P0138-O2 SENSOR 1/2 CIRCUIT HIGH VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
P0152-O2 SENSOR 2/1 CIRCUIT HIGH VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
P0158-O2 SENSOR 2/2 CIRCUIT HIGH VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
P0133-O2 SENSOR 1/1 SLOW RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
P0139-O2 SENSOR 1/2 SLOW RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

ii
bY dR.dEaDhEaD
 TABLE OF CONTENTS - Continued
P0153-O2 SENSOR 2/1 SLOW RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
P0159-O2 SENSOR 2/2 SLOW RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
P0135-O2 SENSOR 1/1 HEATER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . .98
P0141-O2 SENSOR 1/2 HEATER PERFROMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . .98
P0155-O2 SENSOR 2/1 HEATER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . .98
P0161-O2 SENSOR 2/2 HEATER PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . .98
P0171-FUEL SYSTEM 1/1 LEAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
P0174-FUEL SYSTEM 2/1 LEAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
P0172-FUEL SYSTEM 1/1 RICH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
P0175-FUEL SYSTEM 2/1 RICH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
P0201-FUEL INJECTOR NO.1 CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
P0202-FUEL INJECTOR NO.2 CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
P0203-FUEL INJECTOR NO.3 CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
P0204-FUEL INJECTOR NO.4 CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
P0205-FUEL INJECTOR NO.5 CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
P0206-FUEL INJECTOR NO.6 CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
P0300-MULTIPLE CYLINDER MISFIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
P0301-CYLINDER NO.1 MISFIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
P0302-CYLINDER NO.2 MISFIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
P0303-CYLINDER NO.3 MISFIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
P0304-CYLINDER NO.4 MISFIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
P0305-CYLINDER NO.5 MISFIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
P0306-CYLINDER NO.6 MISFIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
P0315-NO CRANK SENSOR LEARNED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
P0335-CRANKSHAFT POSITION SENSOR CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . .124
P0339-CRANKSHAFT POSITION SENSOR INTERMITTENT . . . . . . . . . . . . . . . . . . .128
P0340-CAMSHAFT POSITION SENSOR CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . .132
P0344-CAMSHAFT POSITION SENSOR INTERMITTENT . . . . . . . . . . . . . . . . . . . . .136
P0420-CATALYST 1/1 EFFICIENCY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
P0430-CATALYST 2/1 EFFICIENCY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
P0440-GENERAL EVAP SYSTEM FAILURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
P0441-EVAP PURGE SYSTEM PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
P0443-EVAP PURGE SOLENOID CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
P0452-NVLD PRESSURE SWITCH STUCK CLOSED. . . . . . . . . . . . . . . . . . . . . . . . .152
P0453-NVLD PRESSURE SWITCH STUCK OPEN . . . . . . . . . . . . . . . . . . . . . . . . . . .155
P0455-EVAP SYSTEM LARGE LEAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
P0456-EVAP SYSTEM SMALL LEAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
P0457-LOOSE FUEL FILL CAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162
P0461-FUEL LEVEL SENSOR NO.1 PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . .167
P0462-FUEL LEVEL SENSOR NO.1 LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169
P0463-FUEL LEVEL SENSOR NO.1 HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
P0480-COOLING FAN NO.1 CONTROL CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
P0481-COOLING FAN NO.2 CONTROL CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
P0498-NVLD CANISTER VENT VALVE SOLENOID CIRCUIT LOW. . . . . . . . . . . . . .177
P0499-NVLD CANISTER VENT VALVE SOLENOID CIRCUIT HIGH . . . . . . . . . . . . .179
P0501-VEHICLE SPEED SIGNAL PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . .181
P0506-IDLE SPEED PERFORMANCE LOWER THAN EXPECTED . . . . . . . . . . . . . .184
P0507-IDLE SPEED PERFORMANCE HIGHER THAN EXPECTED . . . . . . . . . . . . .186
P0508-IAC VALVE SIGNAL CIRCUIT LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188
P0509-IAC VALVE SIGNAL CIRCUIT HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190
P0513-INVALID SKIM KEY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
P0516-BATTERY TEMPERATURE SENSOR LOW . . . . . . . . . . . . . . . . . . . . . . . . . . .194
P0517-BATTERY TEMPERATURE SENSOR HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . .196

iii
bY dR.dEaDhEaD
 TABLE OF CONTENTS - Continued
P0522-OIL PRESSURE VOLTAGE LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198
P0532-A/C PRESSURE SENSOR LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200
P0533-A/C PRESSURE SENSOR HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
P0551-POWER STEERING SWITCH PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . .204
P0562-BATTERY VOLTAGE LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206
P0563-BATTERY VOLTAGE HIGH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
P0572-BRAKE SWITCH NO.1 CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211
P0573-BRAKE SWITCH NO.1 CIRCUIT HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213
P0580-SPEED CONTROL SWITCH NO.1 LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215
P0581-SPEED CONTROL SWITCH NO.1 HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217
P0582-SPEED CONTROL VACUUM SOLENOID CIRCUIT . . . . . . . . . . . . . . . . . . . . .220
P0586-SPEED CONTROL VENT SOLENOID CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . .223
P0594-SPEED CONTROL SERVO POWER CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . .226
P0600-SERIAL COMMUNICATION LINK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .229
P0601-INTERNAL MEMORY CHECKSUM INVALID. . . . . . . . . . . . . . . . . . . . . . . . . . .229
P0622-GENERATOR FIELD CONTROL CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .230
P0627-FUEL PUMP RELAY CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .232
P0630-VIN NOT PROGRAMMED IN PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .234
P0632-ODOMETER NOT PROGRAMMED IN PCM . . . . . . . . . . . . . . . . . . . . . . . . . . .235
P0633-SKIM KEY NOT PROGRAMMED IN PCM. . . . . . . . . . . . . . . . . . . . . . . . . . . . .236
P0645-A/C CLUTCH RELAY CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .237
P0685-ASD RELAY CONTROL CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .239
P0688-ASD RELAY SENSE CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .241
P0700-TRANSMISSION CONTROL SYSTEM (MIL REQUEST) . . . . . . . . . . . . . . . . .244
P0850-PARK/NEUTRAL SWITCH PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . .245
P1115-GENERAL TEMPERATURE SENSOR PERFORMANCE . . . . . . . . . . . . . . . . .247
P1593-SPEED CONTROL SWITCH NO.1 STUCK . . . . . . . . . . . . . . . . . . . . . . . . . . . .249
P1603-PCM INTERNAL DUAL-PORT RAM COMMUNICATION . . . . . . . . . . . . . . . . .252
P1604-PCM INTERNAL DUAL-PORT RAM READ/WRITE INTEGRITY FAILURE . . .252
P1607-PCM INTERNAL SHUTDOWN TIMER RATIONALITY . . . . . . . . . . . . . . . . . . .252
P1696-PCM FAILURE EEPROM WRITE DENIED . . . . . . . . . . . . . . . . . . . . . . . . . . . .254
P1697-PCM FAILURE SRI MILES NOT STORED . . . . . . . . . . . . . . . . . . . . . . . . . . . .254
P2096-DOWN STREAM FUEL TRIM LEAN BANK 1 . . . . . . . . . . . . . . . . . . . . . . . . . .256
P2097-DOWN STREAM FUEL TRIM RICH BANK 1 . . . . . . . . . . . . . . . . . . . . . . . . . .256
P2098-DOWN STREAM FUEL TRIM LEAN BANK 2 . . . . . . . . . . . . . . . . . . . . . . . . . .256
P2099-DOWN STREAM FUEL TRIM RICH BANK 2 . . . . . . . . . . . . . . . . . . . . . . . . . .256
P2302-IGNITION COIL NO.1 SECONDARY CIRCUIT- INSUFFICIENT
IONIZATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259
P2305-IGNITION COIL NO.2 SECONDARY CIRCUIT- INSUFFICIENT
IONIZATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259
P2308-IGNITION COIL NO.3 SECONDARY CIRCUIT- INSUFFICIENT
IONIZATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259
P2503-CHARGING SYSTEM OUTPUT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262
U0101-NO BUS MESSAGE FROM TRANS CONTROL MODULE . . . . . . . . . . . . . . .265
U0155-NO CLUSTER BUS MESSAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267
U0168-NO SKIM BUS MESSAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .268
*CHECKING A/C SYSTEM OPERATION WITH NO DTCS . . . . . . . . . . . . . . . . . . . . .270
*CHECKING PCM POWERS AND GROUNDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .274

STARTING
*CHECKING FUEL DELIVERY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275
*CHECKING HARD START (FUEL DELIVERY SYSTEM) . . . . . . . . . . . . . . . . . . . . . .278
*ENGINE CRANKS DOES NOT START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280

iv
bY dR.dEaDhEaD
 TABLE OF CONTENTS - Continued
*FUEL PRESSURE LEAK DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283
*NO CRANK CONDITION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284
*NO RESPONSE FROM PCM WITH A NO START CONDITION . . . . . . . . . . . . . . . .287
*START AND STALL CONDITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .290

TRANSMISSION - 42RLE
P0122-THROTTLE POSITION SENSOR/APPS LOW . . . . . . . . . . . . . . . . . . . . . . . . .292
P0123-THROTTLE POSITION SENSOR/APPS HIGH . . . . . . . . . . . . . . . . . . . . . . . . .294
P0124- THROTTLE POSITION SENSOR/APPS INTERMITTENT. . . . . . . . . . . . . . . .296
P0218-HIGH TEMPERATURE OPERATION ACTIVATED . . . . . . . . . . . . . . . . . . . . . .298
P0562-LOW BATTERY VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300
P0604-INTERNAL TCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303
P0605-INTERNAL TCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .304
P0613-INTERNAL TCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .305
P0706-CHECK SHIFTER SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .306
P0711-TRANSMISSION TEMPERATURE SENSOR PERFORMANCE . . . . . . . . . . . .312
P0712-TRANSMISSION TEMPERATURE SENSOR LOW. . . . . . . . . . . . . . . . . . . . . .315
P0713-TRANSMISSION TEMPERATURE SENSOR HIGH . . . . . . . . . . . . . . . . . . . . .318
P0714-TRANSMISSION TEMPERATURE SENSOR INTERMITTENT . . . . . . . . . . . .321
P0715-INPUT SPEED SENSOR ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323
P0720-OUTPUT SPEED SENSOR ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .327
P0725-ENGINE SPEED SENSOR CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .331
P0731-GEAR RATIO ERROR IN 1ST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .334
P0732-GEAR RATIO ERROR IN 2ND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .336
P0733-GEAR RATIO ERROR IN 3RD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .339
P0734-GEAR RATIO ERROR IN 4TH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .342
P0736-GEAR RATIO ERROR IN REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .345
P0740-TCC OUT OF RANGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .347
P0750-LR SOLENOID CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .349
P0755-2/4 SOLENOID CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .353
P0760-OD SOLENOID CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .357
P0765-UD SOLENOID CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .361
P0841-LR PRESSURE SWITCH SENSE CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . .365
P0845-2/4 HYDRAULIC PRESSURE TEST FAILURE . . . . . . . . . . . . . . . . . . . . . . . . .369
P0846-2/4 PRESSURE SWITCH SENSE CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . .373
P0870-OD HYDRAULIC PRESSURE TEST FAILURE . . . . . . . . . . . . . . . . . . . . . . . . .377
P0871-OD PRESSURE SWITCH SENSE CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . .381
P0884-POWER UP AT SPEED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .385
P0888-RELAY OUTPUT ALWAYS OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .386
P0890-SWITCHED BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .388
P0891-TRANSMISSION RELAY ALWAYS ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .390
P0897-WORN OUT/BURNT TRANSAXLE FLUID. . . . . . . . . . . . . . . . . . . . . . . . . . . . .393
P0944-LOSS OF PRIME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .395
P0992- 2-4/OD HYDRAULIC PRESSURE TEST FAILURE . . . . . . . . . . . . . . . . . . . . .398
P1652-SERIAL COMMUNICATION LINK MALFUNCTION. . . . . . . . . . . . . . . . . . . . . .400
P1684-BATTERY WAS DISCONNECTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .402
P1687-NO COMMUNICATION WITH THE MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .405
P1694-BUS COMMUNICATION WITH ENGINE MODULE. . . . . . . . . . . . . . . . . . . . . .407
P1775-SOLENOID SWITCH VALVE LATCHED IN TCC POSITION . . . . . . . . . . . . . .409
P1776-SOLENOID SWITCH VALVE LATCHED IN LR POSITION. . . . . . . . . . . . . . . .413
P1790-FAULT IMMEDIATELY AFTER SHIFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .417
P1793-TRD LINK COMMUNICATION ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .418
P1794-SPEED SENSOR GROUND ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .421

v
bY dR.dEaDhEaD
 TABLE OF CONTENTS - Continued
P1797-MANUAL SHIFT OVERHEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .423
*BACKUP LAMPS COME ON WHILE SHIFTER IS NOT IN REVERSE POSITION. .425
*BACKUP LAMPS INOPERATIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .427
*CHECKING PARK/NEUTRAL SWITCH OPERATION . . . . . . . . . . . . . . . . . . . . . . . . .430
*INCORRECT TRANSMISSION FLUID LEVEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .432
*NO SPEEDOMETER OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433
*TRANSMISSION NOISY WITH NO DTC’S PRESENT . . . . . . . . . . . . . . . . . . . . . . . .434
*TRANSMISSION SHIFTS EARLY WITH NO DTC’S . . . . . . . . . . . . . . . . . . . . . . . . . .435
*TRANSMISSION SIMULATOR 8333 WILL NOT POWER UP . . . . . . . . . . . . . . . . . .436

VEHICLE THEFT/SECURITY
ANTENNA FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .437
COP FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .437
EEPROM FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .437
INTERNAL FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .437
RAM FAILURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .437
SERIAL LINK INTERNAL FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .437
STACK OVERFLOW FAILURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .437
PCM STATUS FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .439
SERIAL LINK EXTERNAL FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .439
ROLLING CODE FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .441
VIN MISMATCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .441
TRANSPONDER COMMUNICATION FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .443
TRANSPONDER CYCLIC REDUNDANCY CHECK (CRC) FAILURE . . . . . . . . . . . . .443
TRANSPONDER ID MISMATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .443
TRANSPONDER RESPONSE MISMATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .443

VERIFICATION TESTS
VERIFICATION TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .446

8.0 COMPONENT LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .453

8.1 CONTROL MODULES AND PDC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .453

8.2 DATA LINK CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .453
8.3 SENSORS AND SOLENOIDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .454
8.4 FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .457
8.5 SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .458

9.0 CONNECTOR PINOUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .459

A/C COMPRESSOR CLUTCH - BLACK 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .459

A/C HIGH PRESSURE SWITCH (4.0L) - BLACK 2 WAY . . . . . . . . . . . . . . . . . . . . . . .459
A/C LOW PRESSURE SWITCH - GREEN 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . .459
A/C PRESSURE TRANSDUCER (2.4L) - 4 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . .459
AMBIENT TEMPERATURE SENSOR (ENGINE) - 2 WAY . . . . . . . . . . . . . . . . . . . . . .460
BATTERY TEMPERATURE SENSOR - BLACK 2 WAY . . . . . . . . . . . . . . . . . . . . . . . .460
BRAKE LAMP SWITCH - GRAY 6 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .460
C102 - (ENGINE SIDE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .461
C102 - GRAY (HEADLAMP AND DASH SIDE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .461
C103 - BLACK (ENGINE SIDE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .462
C103 - BLACK (HEADLAMP AND DASH SIDE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .462
C104 (RHD) - BLACK (ENGINE SIDE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .462
C104 (RHD) - BLACK (HEADLAMP AND DASH SIDE) . . . . . . . . . . . . . . . . . . . . . . . .463
C181 (2.4L) - BLACK (ENGINE INTAKE SIDE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .463

vi
bY dR.dEaDhEaD
 TABLE OF CONTENTS - Continued
C181 (2.4L) - BLACK (ENGINE SIDE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .463
C182 (2.4L) - BLACK (ENGINE INTAKE SIDE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .463
C182 (2.4L) - BLACK (ENGINE SIDE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .464
CAMSHAFT POSITION SENSOR - BLACK 3 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . .464
CLOCKSPRING C1 - 4 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .464
CLUTCH PEDAL POSITION SWITCH (M/T) - BLACK 2 WAY . . . . . . . . . . . . . . . . . . .464
COIL CAPACITOR - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .465
CRANKSHAFT POSITION SENSOR - BLACK 3 WAY . . . . . . . . . . . . . . . . . . . . . . . . .465
ENGINE COOLANT TEMPERATURE SENSOR - BLACK 2 WAY . . . . . . . . . . . . . . . .465
ENGINE OIL PRESSURE SWITCH - BLACK 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . .465
EVAP/PURGE SOLENOID - 2 WAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .466
FUEL INJECTOR NO. 1 (2.4L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .466
FUEL INJECTOR NO. 1 (4.0L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .466
FUEL INJECTOR NO. 2 (2.4L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .466
FUEL INJECTOR NO. 2 (4.0L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .466
FUEL INJECTOR NO. 3 (2.4L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467
FUEL INJECTOR NO. 3 (4.0L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467
FUEL INJECTOR NO. 4 (2.4L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467
FUEL INJECTOR NO. 4 (4.0L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467
FUEL INJECTOR NO. 5 (4.0L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467
FUEL INJECTOR NO. 6 (4.0L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .468
FUEL PUMP MODULE - 4 WAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .468
GENERATOR - 3 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .468
GENERATOR - BLACK 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .468
IDLE AIR CONTROL MOTOR - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .469
IGNITION COIL PACK (2.4L) - BLACK 3 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .469
IGNITION COIL PACK (4.0L) - BLACK 4 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .469
INPUT SPEED SENSOR - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .469
INTAKE AIR TEMPERATURE SENSOR (2.4L) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . .470
INTAKE AIR TEMPERATURE SENSOR (4.0L) - GRAY 2 WAY . . . . . . . . . . . . . . . . . .470
MANIFOLD ABSOLUTE PRESSURE SENSOR - 3 WAY . . . . . . . . . . . . . . . . . . . . . . .470
NATURAL VACUUM LEAK DETECTION ASSEMBLY - BLACK 3 WAY . . . . . . . . . . .470
OUTPUT SPEED SENSOR (A/T) - 2 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .471
OXYGEN SENSOR 1/1 UPSTREAM (2.4L) - 4 WAY . . . . . . . . . . . . . . . . . . . . . . . . . .471
OXYGEN SENSOR 1/1 UPSTREAM (4.0L) - 4 WAY . . . . . . . . . . . . . . . . . . . . . . . . . .471
OXYGEN SENSOR 1/2 DOWNSTREAM - BLACK 4 WAY . . . . . . . . . . . . . . . . . . . . .471
OXYGEN SENSOR 2/1 UPSTREAM (4.0L) - 4 WAY . . . . . . . . . . . . . . . . . . . . . . . . . .472
OXYGEN SENSOR 2/2 DOWNSTREAM (4.0L) - 4 WAY . . . . . . . . . . . . . . . . . . . . . . .472
FUSES (PDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .474
A/C COMPRESSOR CLUTCH RELAY (IN PDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .474
AUTOMATIC SHUT DOWN RELAY (IN PDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .474
ENGINE STARTER MOTOR RELAY (IN PDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .475
FUEL PUMP RELAY (IN PDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .475
HIGH SPEED RADIATOR FAN RELAY (2.4L). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .475
LOW SPEED RADIATOR FAN RELAY (2.4L) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .475
TRANSMISSION CONTROL RELAY (IN PDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .475
POWER STEERING PRESSURE SWITCH (2.4L) - BLACK 2 WAY . . . . . . . . . . . . . .476
POWERTRAIN CONTROL MODULE C1 - BLACK/BLACK 38 WAY . . . . . . . . . . . . . .476
POWERTRAIN CONTROL MODULE C2 - BLACK/ORANGE 38 WAY . . . . . . . . . . . .477
POWERTRAIN CONTROL MODULE C3 - BLACK/NATURAL 38 WAY . . . . . . . . . . . .478
POWERTRAIN CONTROL MODULE C4 - BLACK/GREEN 38 WAY. . . . . . . . . . . . . .479
RADIATOR FAN MOTOR (2.4L) - 3 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .479
RADIATOR FAN MOTOR CIRCUIT BREAKER (2.4L) - 2 WAY . . . . . . . . . . . . . . . . . .480

vii
bY dR.dEaDhEaD
 TABLE OF CONTENTS - Continued
SENTRY KEY IMMOBILIZER MODULE - BLACK 6 WAY . . . . . . . . . . . . . . . . . . . . . .480
SPEED CONTROL SERVO - BLACK 4 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .480
THROTTLE POSITION SENSOR (2.4L) - 3 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . .480
THROTTLE POSITION SENSOR (4.0L) - 3 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . .481
TOW/HAUL OVERDRIVE OFF SWITCH - 4 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . .481
TRANSFER CASE SWITCH (EXCEPT OFF-ROAD PACKAGE) - BLACK 2 WAY . . .481
TRANSFER CASE SWITCH (OFF-ROAD PACKAGE) - BLACK 2 WAY . . . . . . . . . . .481
TRANSMISSION RANGE SENSOR - 10 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .482
TRANSMISSION SOLENOID/PRESSURE SWITCH ASSEMBLY - 10 WAY . . . . . . . .482
VEHICLE SPEED SENSOR - BLACK 3 WAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .482

10.0 SCHEMATIC DIAGRAMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .483

10.1 2.4L NGC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .483

10.2 4.0L NGC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .484
10.3 42 RLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .485

11.0 CHARTS AND GRAPHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .487

11.1 2.4L ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .487

11.2 4.0L ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .487
11.3 PRESSURE SWITCH STATES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .487
11.4 SOLENOID APPLICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .488
11.5 SHIFT LEVER ERROR CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .488
11.6 TRANSMISSION TEMPERATURE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . .489

viii
bY dR.dEaDhEaD
 GENERAL INFORMATION
Important
New for TJ, the Powertrain Control Module and Transmission Control Module have been
combined into single control module on all vehicles equipped with a 2.4L and 4.0L engines. This
new module is the Next Generation Controller (NGC). New Diagnostics procedures along with
new DTC’s are two of the changes you will see which reflect the new combined module
technology. The NGC modules will have four color coded connectors C1/A through C4/D,
(C1-BLK, C2-ORANGE, C3-WHITE, C4-GREEN). Each PCM connector has 38 pins. Two new tools
were introduced to help diagnose and repair the new PCM (NGC) terminals and harness
connectors. The Miller #3638 terminal removal pick must be used to release the connector
terminals, or harness and connector damage will occur. Also, the Miller #8815 Pin Out Box was
introduced. You must use the Miller #8815 tool instead of probing the PCM terminals, or harness
and connector damage will occur. There is also a new Verification test and module replacement
procedure for the new PCM.

1.0 INTRODUCTION 1.1 SYSTEM COVERAGE

The procedures contained in this manual include This diagnostic procedure manual covers Power-
specifications, instructions, and graphics needed to train, Transmission, and Transfer Case diagnostics
diagnose the PCM Powertrain System. The diag- for 2005 TJ vehicles equipped with the Next Gen-
nostics in this manual are based on the failure eration Control Module (NGC).
condition or symptom being present at the
time of diagnosis. Please follow the recommenda- 1.2 SIX-STEP TROUBLE SHOOTING
tions below when choosing your diagnostic path. PROCEDURE
1. First make sure the DRBIIIt is communicating
with the appropriate modules; i.e., if the DRBIIIt Diagnosis of the Powertrain Control Module
displays a 9No Response9 condition, you must diag- (PCM) is done in six basic steps:
nose this first before proceeding. • verification of complaint
2. Read DTCs (diagnostic trouble codes) with the
• verification of any related symptoms
DRBIIIt.
3. If no DTCs are present, identify the customer • symptom analysis
complaint. • problem isolation
4. Once the DTC or customer complaint is iden- • repair of isolated problem
tified, locate the matching test in the Table of
• verification of proper operation
Contents and begin to diagnose the symptom.
All component location views are in Section 8.0.
All connector pinouts are in Section 9.0. All system 2.0 IDENTIFICATION OF
schematic diagrams are in Section 10.0. All charts
and graphs are in section 11.0. SYSTEM
An * placed before the symptom description indi-
The Powertrain Control Module (PCM) monitors
cates a customer complaint.
and controls:
When repairs are required, refer to the appropri-
ate service manual for the proper removal and • fuel system
repair procedure. • ignition system
Diagnostic procedures change every year. New • charging system
diagnostic systems may be added; current systems
• speed control system
may be enhanced. READ THIS MANUAL BEFORE
TRYING TO DIAGNOSE A VEHICLE DTC. It is • The NGC control module is used on the 2.4L and
recommended that you review the entire manual to 4.0L engines with an automatic or manual trans-
become familiar with all new and enhanced diag- mission.
nostic procedures. • The 42RLE transmission can be identified by
After using this book, if you have any comments confirming a Solenoid/Pressure Switch Assembly
or recommendations, please fill out the form at the located on the right side of the transmission, The
back of the book and mail it back to us. Transmission Range Sensor, Input Speed Sensor
and Output Speed Sensor are located on the left
side of the transmission. Refer to the Service
Information for transmission ID tag descriptions.

1
bY dR.dEaDhEaD
GENERAL INFORMATION
3.0 SYSTEM DESCRIPTION AND It is possible that a trouble code for a monitored
circuit may not be entered into the PCM/ECM
FUNCTIONAL OPERATION
memory even though a malfunction has occurred.
This may happen because one of the trouble code
3.1 GENERAL DESCRIPTION criteria (arming conditions) has not been met.
The PCM compares input signal voltage from
each input component to specifications (the estab-
POWERTRAIN lished high and low limits of the range) that are
The on-board OBDII diagnostics incorporated preprogrammed for that component. If the input
with the PCM are intended to assist the field voltage is not within specifications, and other trou-
technician in repairing vehicle problems by the ble code criteria (arming conditions) are met, a
quickest means. trouble code will store in the PCM memory.
The On Board Diagnostics have evolved to the
TRANSMISSION second Generation of Diagnostics referred to as
The 42RLE electronic Transmission is a conven- OBDII. These OBDII Diagnostics control the func-
tional Transmission in that it uses hydraulically tions necessary to meet the requirements of Cali-
applied clutches to shift a planetary gear train. fornia OBDII and Federal OBD regulations. These
However, the electronic control system replaces requirements specify the inclusion of a Malfunction
many of the mechanical and hydraulic components Indicator Light (MIL) located on the instrument
used in conventional transmission valve bodies. panel for all 1994 and subsequent model-year pas-
senger cars, light duty trucks, and medium-duty
3.2 FUNCTION OPERATION vehicles. The purpose of the MIL is to inform the
vehicle operator in the event of the malfunction of
any emission system or component failures that can
3.2.1 FUEL CONTROL (GAS) affect emissions and which provide input to, or
receive output from, the PCM.
The PCM controls the air/fuel ratio of the engine
by varying fuel injector-on time. Mass air flow is MIL Lamp Strategy
calculated using the speed density method using I/M Readiness OK to test = Key On Engine OFF
engine speed and manifold absolute pressure (IAT - MIL Lamp will remain on until the vehicle is
is a modifier in Speed Density). started or Ignition is turned off.
Different fuel calculation strategies are used de- I/M not ready for testing = Key On Engine OFF
pending on the operational state of the engine. - MIL Lamp on solid for (15) seconds then MIL
During crank mode, a prime shot fuel pulse is Lamp will flash on/off for (5) seconds then it will
delivered followed by fuel pulses determined by a remain on until the vehicle is started or the Ignition
crank time strategy. Cold engine operation is deter- is turned off.
mined via an open loop strategy until the O2
sensors have reached operating temperature. At
this point, the strategy enters a closed loop mode
where fuel requirements are based upon the state of
the O2 sensors, engine speed, MAP, throttle posi-
tion, air temperature, battery voltage, and coolant
temperature.

3.2.2 ON-BOARD DIAGNOSTICS

The PCM has been programmed to monitor any
circuit or system that has an effect on vehicle
emissions, or is used by the PCM to determine the
proper functionality of these systems. This monitor-
ing is called 9on-board diagnosis.’’
Certain criteria or, 9arming conditions’’, must be
met before a trouble code will be entered into the
PCM memory. The criteria range from engine rpm,
engine temperature, and/or input voltage to the
The following table summarizes the various
PCM. If a problem is detected with a monitored
OBDII monitors operation.
circuit, and all of the criteria or arming conditions
are met, a trouble code will be stored in the PCM.

2
bY dR.dEaDhEaD
 GENERAL INFORMATION
OBD II Monitor Operation

Comprehensive Major Monitors Major Monitors

Components Non Fuel Control Fuel Control
Monitor & Non Misfire & Misfire

Run constantly Run Once Per Trip Run constantly

Includes All Engine Hardware Monitors Entire Emission Monitors Entire System
Sensors, Switches, Solenoids, System
etc.

Most are One Trip Faults - Most are Two Trip Faults - Two Trip Faults - Turns On
Usually Turns On Turns On The MIL and Sets DTC After
The MIL and Sets DTC After The MIL and Sets DTC After Two Consecutive Failure
One Failure Two Consecutive Failure

Priority 3 Priority 1 or 3 Priority 2 or 4

All Checked For Continuity Done Stop Testing = Yes Fuel Control Monitor
Open Oxygen Sensor Heater Monitors Fuel Control
Short To Ground Oxygen Sensor Response System For:
Short To Voltage Fuel System Lean
Fuel System Rich
Inputs Checked For Rationality Catalytic Converter Requires 3 Consecutive
Efficiency Except EWMA up to Fuel System Good Trips to
6 tests per trip Extinguish the MIL
Outputs Checked For
and a one trip fault (SBEC)
Functionality
and a two-trip fault on JTEC

EGR System Evaporative Misfire Monitor

Emission Monitors for Engine Misfire
System At:
(Purge and Leak) 4 X 1000 RPM Counter (4000
Non-LDP Revs)
or (Type B)
LDP **200 X 3 (600) RPM Counter
(Type A)

Requires 3 Consecutive Good Requires 3 Consecutive Good Requires 3 Consecutive

Trips to Extinguish the MIL* Trips to Extinguish the MIL* Good Trips
To Extinguish the MIL

*40 Warm Up Cycles are required to erase **Type A misfire is a one trip
DTCs after the MIL has been extinguished. failure on pre-1999, 2 Trip
failure on 1999 and later. The
MIL will illuminate at the first
or second failure, based on MY.

3
bY dR.dEaDhEaD
GENERAL INFORMATION
OBDII MONITOR RUN PROCESS NOTE
NGC VEHICLES A. Only the monitors, which are not YES in
The following procedure has been established to the CARB Readiness Status, need to be
assist Chrysler Dealer Technicians in the field with completed.
enabling and running OBD II Monitors. The order B. Specific criteria need to be met for each
listed in the following procedure is intended to monitor. Each monitor has a Pre-Test screen
allow the technician to effectively complete each to assist in running the monitor.
monitor and to set the CARB Readiness Status in For additional information, refer to the
the least time possible. Chrysler Corporation Technical Training
NOTE Workbook titled On Board Diagnostics:
A. Once the monitor run process has begun, OBDII/EOBD, part number 81-699-01050.
do not turn off the ignition. By turning the C. The most efficient order to run the
ignition key off, monitor enabling conditions monitors has been outlined below, including
will be lost. NVLD Monitor runs after key off. suggestions to aid the process.
B. By performing a Battery Disconnect, or 1. Natural Vacuum Leak Detection with Purge
Selecting Erase DTCs, the CARB Readiness Monitor
and all additional OBD II information will be This monitor requires a cool down cycle, usually
cleared. an overnight soak for at least 8 hours without the
Monitor Preliminary Checks: engine running. The ambient temperature must
1. Plug a DRB IIIt into the vehicle’s DLC. decrease overnight - parking the vehicle outside is
2. Turn the ignition, KEY ON - ENGINE OFF. advised. To run this test the fuel level must be
Watch for MIL lamp illumination during the bulb between 15-85% full. For the monitor run condi-
check. MIL lamp must have illuminated, if not, tions select the EVAP MON PRE-TEST in the
repair MIL lamp. DRB IIIt, OBD II Monitors Menu. The Purge mon-
3. On the DRB IIIt Select #1 DRBIIIt Stand- itor will run if the small leak test reports a pass.
alone. Criteria for NVLD monitor
4. Select #1 1998-2003 Diagnostics 1) Engine off time greater than one hour
5. Select #1 Engine 2) Fuel Level between 15% and 85%
6. Select #2 DTCs and Related Functions 3) Start Up ECT and IAT within 10° C (18° F).
7. Select #1 Read DTCs 4) Vehicle started and run until Purge Monitor
* Verify that No Emissions Related DTCs are reports a result.
Present. Note: If the vehicle does not report a result and
* If an Emissions DTC is Present, the OBD II the conditions where correct. It may take up to two
Monitors may not run and the CARB Readiness will weeks to fail the small leak monitor. DO NOT use
not update. this test to attempt to determine a fault. Use the
*The Emissions related DTC, will need to be appropriate service information procedure for find-
repaired, then cleared. By clearing DTCs, the OBD ing a small leak. If there are no faults and the
Monitors will need to be run and completed to set conditions are correct this test will run and report a
the CARB Readiness Status. pass. Note the Small leak test can find leaks less
8. Return to Engine Select Function Menu and than 10 thousands of an inch. If a small leak is
Select #9, OBD II Monitors. present it takes approximately one week of normal
9. Select #3 CARB Readiness Status. driving to report a failure.
Do all the CARB Readiness Status Locations read
YES? 2. Catalyst / O2 Monitor
*YES, then all monitors have been completed and With NGC, Catalyst and O2 Monitor information
this vehicle is ready to be I/M or Emission Tested. are acquired and processed at the same time. Most
*NO, then the following procedure needs to be vehicles will need to be driven at highway speed
followed to run/complete all available monitors. (< 50 mph) for a few minutes. Some trucks run the
monitor at idle in drive. If the vehicle is equipped
with a manual transmission, using 4th gear may
assist in meeting the monitor running criteria. For
the monitor run conditions, select the BANK 1 CAT
MON PRE-TEST in the DRB IIIt, OBD II Monitors
Menu.

4
bY dR.dEaDhEaD
 GENERAL INFORMATION
3. EGR Monitor 3.2.3.1 TRANSMISSION OPERATION AND
The EGR monitor now runs in a closed throttle
decel or at idle on a warm vehicle. However, it is SHIFT SCHEDULING AT VARIOUS
necessary to maintain the TPS, Map and RPM OIL TEMPERATURES
ranges to allow the monitor to complete itself. For
The transmission covered in this manual has
the monitor run conditions, select the EGR PRE-
unique shift schedules depending on the tempera-
TEST in the DRB IIIt, OBD II Monitors Menu.
ture of the transmission oil. The shift schedule is
4. O2 Sensor Heater Monitor modified to extend the life of the transmission while
This monitor is now continuously running once operating under extreme conditions.
the heaters are energized. Pass information will be The oil temperature is measured with a Temper-
processed at power down. For the monitor run ature Sensor on the 42RLE transmission. The Tem-
conditions, select the O2S HEATER MON PRE- perature Sensor is an integral component of the
TEST in the DRB IIIt, OBD II Monitors Menu. Transmission Range Sensor (TRS). If the Tempera-
ture Sensor is faulty, the transmission will default
3.2.3 TRANSMISSION CONTROL to a calculated oil temperature. Oil temperature
will then be calculated through a complex heat
The 42RLE electronic Transmission has a fully
transfer equation using engine coolant tempera-
adaptive control system. The system performs it’s
ture, battery/ambient temperature, and engine off
functions based on continuous real-time sensor
time from the Body Control Module (BCM). These
feedback information. The control system automat-
inputs are received from the PCI bus periodically
ically adapts to changes in engine performance and
and used to initialize the oil temperature at start
friction element variations to provide consistent
up. Once the engine is started, the PCM updates
shift quality. The control system ensures that clutch
the transmission oil temperature based on torque
operation during upshifting and downshifting is
converter slip speed, vehicle speed, gear, and engine
more responsive without increased harshness. The
coolant temperature to determine an estimated oil
Powertrain Control Module (PCM) continuously
temperature during vehicle operation. Vehicles us-
checks for electrical problems, mechanical prob-
ing calculated oil temperature track oil tempera-
lems, and some hydraulic problems. When a prob-
ture reasonably accurate during normal operation.
lem is sensed, the PCM stores a diagnostic trouble
However, if a transmission is overfilled, a transmis-
code. Some of these codes cause the Transmission to
sion oil cooler becomes restricted, or if a customer
go into Limp-in mode. While in this mode, electrical
drives aggressively in low gear, the calculated oil
power is taken away from the Transmission via the
temperature will be inaccurate. Consequently the
PCM, de-energizing the transmission control relay,
shift schedule selected may be inappropriate for the
and taking power from the solenoid pack. When this
current conditions. The key highlights of the vari-
happens, the only Transmission mechanical func-
ous shift schedules are as follows:
tions are:
Park and Neutral Extreme Cold: Oil temperature at start up below
Reverse 26.6°C (-16 °F)
Second Gear > Goes to Cold schedule above -24°C (-12°F) oil
No upshifts or downshifts are possible. The posi- temperature
tion of the manual valve alone allows the three > Park, Reverse, Neutral and 2nd gear only (pre-
ranges that are available. Although vehicle perfor- vents shifting which may fail a clutch with fre-
mance is seriously degraded while in this mode, it quent shifts)
allows the owner to drive the vehicle in for service.
Once the DRBIIIt is in the Transmission portion Cold: Oil temperature at start up above -24°C
of the diagnostic program, it constantly monitors (-12°F) and below 2.2°C (36°F)
the transmission to see if the system is in Limp-in > Goes to Warm schedule above 4.4°C (40°F) oil
mode. If the Transmission is in Limp-in mode, the temperature
DRBIIIt will flash the red LED. > Delayed 2-3 upshift approximately 35-50 Km/h
When a problem is sensed, the PCM stores a (22 - 31 MPH)
diagnostic trouble code (DTC). Some of these codes
cause the transmission to go into 9limp-in9 or 9de- > Delayed 3-4 upshift 72-85 Km/h (45-53 MPH)
fault9 mode. > Early 4-3 coastdown shift approximately 48
Once the DRBIII is in the 9Transmission9 portion Km/h (30 MPH)
of the diagnostic program, it constantly monitors > Early 3-2 coastdown shift approximately 27
the PCM to see if the system is in limp-in mode. If Km/h (17 MPH) ?
the transmission is in limp-in mode, the DRBIIIt
will flash the red LED.

5
bY dR.dEaDhEaD
GENERAL INFORMATION
> High speed 4-2, 3-2, 2-1 kickdown shifts are > Aggressive driving in low gear
prevented > Trailer towing in OD gear position (use 3 position
> No EMCC (or A/S 3rd) if frequent shifting occurs)
Warm: Oil temperature at start up above 2.2°C > Cooling system failure causing engine to operate
(36°F) and below 27°C (80°F) over 110°C (230°F)
> Goes to a Hot schedule above 27°C (80°F) oil > Engine coolant temperature stays low too long -
temperature If engine coolant temperature drops below 65°C
(150°F), the transmission will disengage EMCC.
> Normal operation (upshifts, kickdowns, and
Extended operation with the EMCC disengaged
coastdowns)
will cause the transmission to overheat.
> No EMCC
> Brake switch issue will cause the EMCC to
Hot: Oil temperature at start up above 27°C disengage. Extended operation with the EMCC
(80°F) disengaged will cause the transmission to over-
> Goes to a Overheat schedule above 115°C (240°F) heat.
oil temperature > Transmission fluid overfilled
> Normal operation (upshifts, kickdowns, and > Transmission cooler or cooler lines restricted
coastdowns) > Transmission Temperature Sensor circuit
> Full EMCC, No PEMCC except to engage
FEMCC, except at closed throttle at speeds above 3.2.4 O2 SENSOR (NGC)
113-133 Km/h (70 - 83 MPH) The O2 system will with ignition on and engine
Overheat: Oil temperature above 115°C off have a normalized O2 voltage of around 5 volts
(240 °F) or engine coolant temperature above as displayed on the DRBIII or measured with a high
118°C (244°F) impedance voltmeter. As the O2 sensor starts gen-
> Goes to a Hot below 110°C (230°F) oil tempera- erating a signal the voltage will move towards 2.5
ture or a Super Overheat above 115°C (240°F) oil volts. The voltage will typically vary between 2.5
temperature volts and 3.5 volts on a normal running engine. The
goal voltage is also typically between 2.5 and 3.5
> Delayed 2-3 upshift 40-51 Km/h (25-32 MPH) volts. This implies that the 0-volt through 1-volt
> Delayed 3-4 upshift 66-77 Km/h (41-48 MPH) range that you are used to is still valid, only it is
> 3rd gear FEMCC from 48-77 Km/h (30-48 MPH) shifted up by a 2.5 volt offset. This 2.5 volt supply is
> 3rd gear PEMCC from 43-50 Km/h (27-31 MPH) being delivered through the sensor return line.

Super Overheat: Oil temperature above 127°C 3.2.5 OTHER CONTROLS

(260°F)
> Goes back to a Overheat below 115°C (240°F) oil Charging System (NGC)
temperature The charging system is turned on when the
> All a Overheat shift schedules features apply engine is started. The Generator Field is controlled
by the PCM using a 12-volt high side driver and a
> 2nd gear PEMCC above 35 Km/h (22 MPH) body ground. The PCM determines the Generator
> Above 35 Km/h (22 MPH) the torque converter output voltage by an input from the Battery Tem-
will not unlock unless the throttle is closed (i.e. at perature Sensor. The PCM applies a longer duty
80 Km/h (50 MPH) a 4th FEMCC to 3rd FEMCC cycle on time to the Generator Field Control circuit
shift will be made during a part throttle kick- when more system voltage is needed. When a lower
down or a 4th FEMCC to 2nd PEMCC shift will system voltage is needed, the PCM shortens the
be made at wide open throttle) or if a wide open duty cycle on time of the high side driver.
throttle 2nd PEMCC to 1 kickdown is made.
Vehicle Speed Control (NGC)
Causes for operation in the wrong tempera- The PCM controls vehicle speed by operation of
ture shift schedule:
the speed control servo vacuum and vent solenoids.
Extreme Cold or Cold shift schedule at start up:
Energizing the vacuum solenoid applies vacuum to
> Temperature Sensor circuit. the servo to increase throttle position. Operation of
> Overheat or Super Overheat shift schedule after the vent solenoid slowly releases the vacuum allow-
extended operation: ing throttle position to decrease. A special dump
> Operation in city traffic or stop and go traffic solenoid allows immediate release of throttle posi-
tion caused by braking, cruise control turn off,
> Engine idle speed too high

6
bY dR.dEaDhEaD
 GENERAL INFORMATION
shifting into neutral, excessive RPM (tires spin- The normally closed valve in the NVLD is in-
ning) or ignition key off. tended to maintain the seal on the evaporative
NATURAL VACUUM LEAK DETECTION (NVLD) system during the engine off condition. If vacuum in
The Natural Vacuum Leak Detection (NVLD) the evaporative system exceeds 39 to 69 H2O (0.75 to
system is the next generation evaporative leak 1.5 KPA), the valve will be pulled off the seat,
detection system that will first be used on vehicles opening the seal. This will protect the system from
equipped with the Powertrain Control Module excessive vacuum as well as allowing sufficient
(PCM) or Next Generation Controller (NGC) start- purge flow in the event that the solenoid was to
ing in 2002 M.Y. This new system replaces the leak become inoperative. The solenoid actuates the valve
detection pump as the method of evaporative sys- to unseal the canister vent while the engine is
tem leak detection. The current CARB requirement running. It also will be used to close the vent during
is to detect a leak equivalent to a 0.0209 (0.5 mm) the medium and large leak tests and during the
hole. This system has the capability to detect holes purge flow check. This solenoid requires initial 1.5
of this size very dependably. amps of current to pull the valve open but after 100
The basic leak detection theory employed with ms. will be duty cycled down to an average of about
NVLD is the 9Gas Law9. This is to say that the 150 mA for the remainder of the drive cycle.
pressure in a sealed vessel will change if the tem- Another feature in the NVLD Assembly is a
perature of the gas in the vessel changes. The vessel diaphragm that will open the seal with pressure in
will only see this effect if it is indeed sealed. Even the evaporative system. The seal will be opened at
small leaks will allow the pressure in the vessel to about 0.59 H2O (0.12 KPA) pressure to permit the
come to equilibrium with the ambient pressure. In venting of vapors during refueling. An added bene-
addition to the detection of very small leaks, this fit to this is that it will also allow the tank to
system has the capability of detecting medium as 9breathe9 during increasing temperatures, thus lim-
well as large evaporative system leaks. iting the pressure in the tank to this low level. This
is beneficial because the induced vacuum during a
The NVLD utilizes the Gas Law principles subsequent declining temperature will achieve the
A vent valve seals the canister vent during engine switch closed (pass threshold) sooner than if the
off conditions. If the vapor system has a leak of less tank had to decay from a built up pressure.
than the failure threshold, the evaporative system The NVLD Assembly itself has 3 wires: Switch
will be pulled into a vacuum, either due to the cool sense, solenoid driver and ground. It also includes a
down from operating temperature or diurnal ambi- resistor to protect the switch from a short to battery
ent temperature cycling. The diurnal effect is con- or a short to ground. The PCM utilizes a high-side
sidered one of the primary contributors to the leak driver to energize and duty-cycle the solenoid.
determination by this diagnostic.
When the vacuum in the system exceeds about 19 The PCM’s Role in NVLD Diagnosis:
H2O (0.25 KPA), a vacuum switch closes. The The integral part of the diagnostic system that
switch closure sends a signal to the PCM. The PCM, makes engine-off leak detection possible is a special
via appropriate logic strategies (described below), circuit in the PCM controller. After the vehicle is
utilizes the switch signal, or lack thereof, to make a turned off, a special part of the controller stays alive
determination of whether a leak is present. and monitors for an NVLD switch closure. This
circuit within the PCM is very specific in its func-
The NVLD Device and how it functions tion and consumes very little power. If a switch
The NVLD Assembly is designed with a normally closure is detected, it will log the event and time
open vacuum switch, a normally closed solenoid, from key-off, and then power down. This informa-
and a seal, which is actuated by both the solenoid tion will be processed at the next key cycle.
and a diaphragm. The NVLD is located on the
atmospheric vent side of the canister. The NVLD NVLD Leak Detection
Assembly is mounted on top of the canister outlet Small Leak Test (Passive)
for the DN. If, after a specified delay after key off (perhaps 5
The normally open vacuum switch will close with minutes), the switch closes or is closed, the test will
about 19 H2O (0.25 KPA) vacuum in the evaporative be pass, indicating that there is no leak. The PCM
system. The diaphragm actuates the switch. This is records the switch closure. The NVLD circuit in the
above the opening point of the fuel inlet check valve PCM will shut down for the remainder of that
in the fill tube so cap off leaks can be detected. particular engine off (soak) period. When the engine
Submerged fill systems must have recirculation lines is started, the switch closure is recorded as a 9Pass,9
that do not have the in-line normally closed check and the timers that are recording accumulated time
valve that protects the system from failed nozzle are reset.
liquid ingestion, in order to detect cap off conditions.

7
bY dR.dEaDhEaD
GENERAL INFORMATION
This diagnostic test can take at least a week to 2. Purge Flow:
mature a leak fault. A week has been chosen for this The above rationality check is considered suffi-
because the vehicle will have been exposed to the cient to confirm purge solenoid function and con-
largest possible drive scenarios before a decision is formance with the purge flow test requirement. The
made (most vehicles should see both daily work and Purge Flow Monitor is passed based on switch
weekend driving cycles). This also satisfies CARB’s activity when purge is turned on or based on a rich
stated goal of getting 3 MIL illuminations within a fuel control shift when purge is turned on.
month for 0.0209 (0.5 mm) leak detection diagnostic.
Medium and Large Leak Test (Intrusive)
The diagnostics will log engine run time and
engine off time to determine when a week has NOTE: This intrusive test will only be run if
elapsed. There is a limit on the total amount of run the Small Leak (passive) test fails, or is
time that is applied to the one-week timer. There is
inconclusive (the switch does not close)
also a limit on the total soak time that will be
Enabling Conditions:
allowed to apply to the one-week timer. There will
be a limit on the amount of accrued run time during • 40 °F to 90 °F
one specific drive that can be applied to the one- • Engine temperature at startup within 10 °F of
week timer. the ambient temperature
The enabling criteria to run this monitor are: • Fuel level less than 85%
• Fuel level less than 85% The intrusive Medium and Large leak are con-
• Ambient temperature greater than 40 °F (4.4 °C) ducted as follows:
• De-energize the NVLD solenoid to seal the can-
Rationality Tests
ister vent.
1. The rationality check of the switch, solenoid and
seal will be performed as follows: • Activate purge shortly after closed loop. Pull the
tank vacuum past the vacuum switch point (19
• At key-on, the NVLD solenoid will be energized to
H2O vacuum) of the NVLD for a specific time
vent any vacuum that may be trapped in the
while tracking the standard purge flow rate.
evaporative system from the previous soak. This
should result in an open switch condition. • Turn purge off and determine how long it takes to
decay the tank vacuum and reopen the switch.
• The solenoid will be de-energized (to seal the
Determine the leak size from the time it took to
system) at the point where purge begins. The
reopen the switch. Note: Fuel level is an impor-
system / NVLD component rationality passes for
tant determining factor.
that drive cycle if the switch closes after purge
begins. • If the switch does not close, a more aggressive
purge flow will be applied to determine if it is a
• The solenoid is then re-energized for the remain-
very large leak, missing fuel cap, problem with
der of the drive cycle.
the NVLD device, purge flow problem, etc...
• If the switch events are not seen in a certain
period of time, the rationality check will have
failed (2 trip rule).

8
bY dR.dEaDhEaD
 GENERAL INFORMATION

9
bY dR.dEaDhEaD
GENERAL INFORMATION
TEST EQUIPMENT Exhaust System - The PCM cannot detect a
The Evaporative Emission Leak Detector (EELD) plugged, restricted, or leaking exhaust system.(*)
Miller Special Tool 8404 is capable of visually de-
Cylinder Compression - The PCM cannot detect
tecting leaks in the evaporative system and will
uneven, low, or high engine cylinder compres-
take the place of the ultrasonic leak detector 6917A.
sion.(*)
The EELD utilizes shop air and a smoke generator
to visually detect leaks down to 0.020 or smaller. Excessive Oil Consumption - Although the PCM
The food grade oil used to make the smoke includes monitors the exhaust oxygen content through the
an UV trace dye that will leave telltale signs of the oxygen sensor when the system is in a closed loop, it
leak under a black light. This is helpful when cannot determine excessive oil consumption.
components have to be removed to determine the
exact leak location. For detailed test instructions, NOTE: Any of these conditions could result
follow the operators manual packaged with the in a rich or lean condition causing an oxygen
EELD. sensor trouble code to be stored in the PCM,
or the vehicle may exhibit one or more of the
3.2.6 NON-MONITORED CIRCUITS driveability symptoms listed in the Table of
The PCM does not monitor the following circuits, Contents.
systems, and conditions even though they could
have malfunctions that result in driveability prob- 3.3 DIAGNOSTIC TROUBLE CODES
lems. A diagnostic code may not be displayed for the
following conditions. However, problems with these Diagnostic trouble codes (DTCs) are codes stored
systems may cause a diagnostic code to be displayed by the Powertrain Control Module (PCM) that help
for other systems. For example, a fuel pressure us diagnose Powertrain, Transmission and Trans-
problem will not register a diagnostic code directly, fercase problems. They are viewed using the
but could cause a rich or lean condition. This could DRBIIIt scan tool. Always begin by performing a
cause an oxygen sensor, fuel system, or misfire visual inspection of the wiring, connectors, fluid
monitor trouble code to be stored in the PCM. level, cooler lines, engine, and the transmission.
Any obvious wiring problems or leaks should be
Engine Timing - The PCM cannot detect an in-
repaired prior to performing any diagnostic test
correctly indexed timing chain, camshaft sprocket,
procedures. Some engine driveability problems can
or crankshaft sprocket. The PCM also cannot detect
be misinterpreted as a transmission problem. En-
an incorrectly indexed distributor or Cam sensor.(*)
sure that the engine is running properly and that
Fuel Pressure - Fuel pressure is controlled by the no engine DTCs are present that could cause a
fuel pressure regulator. The PCM cannot detect a transmission complaint. If there is a communica-
clogged fuel pump inlet filter, clogged in-line filter, tion bus problem, trouble codes will not be accessi-
or a pinched fuel supply.(*) ble until the problem is fixed. The DRBIIIt will
display an appropriate message. The following is a
Fuel Injectors - The PCM cannot detect a clogged possible list of causes for a bus problem:
fuel injector, a sticking pintle, or that an incorrect – open or short to ground/battery in PCI bus
injector is installed.(*) circuit.
Fuel Requirements - Poor quality gasoline can – internal failure of any module or component on
cause problems such as hard starting, stalling, and the bus
stumble. Use of methanol-gasoline blends may re- Each diagnostic trouble code is diagnosed by
sult in starting and driveability problems. (See following a specific testing sequence. The diagnostic
individual symptoms and their definitions in Sec- test procedures contain step-by-step instructions
tion 6.0 (Glossary of Terms). for determining the cause of a transmission diag-
nostic trouble code. Possible sources of the code are
PCM Grounds - The PCM cannot detect a poor checked and eliminated one by one. It is not neces-
system ground. However, a diagnostic trouble code sary to perform all of the tests in this book to
may be stored in the PCM as a result of this diagnose an individual code. These tests are based
condition. on the problem being present at the time that the
test is run.
Throttle Body Air Flow - The PCM cannot detect If the Engine or Transmission records a DTC that
a clogged or restricted air cleaner inlet or filter will adversely affect vehicle emissions, it will re-
element.(*) quest (via the communication bus) that the PCM
illuminate the Malfunction Indicator Lamp (MIL).
Although these DTCs will be stored in the PCM

10
bY dR.dEaDhEaD
 GENERAL INFORMATION
immediately as a 1 trip failure, it may take up to 3.3.3 INTERMITTENT CODE
five minutes of accumulated trouble confirmation to
A diagnostic trouble code that is not present every
set the DTC and illuminate the MIL. Three consec-
time the PCM checks the circuit is an 9intermittent’’
utive successful OBDII/EURO III trips or clearing
code. Most intermittent codes are caused by wiring
the DTCs with a diagnostic tool (DRBIIIt or equiv-
or connector problems. Intermittent conditions that
alent) is required to extinguish the MIL. When the
come and go like this are the most difficult to
Transmission requests that the PCM illuminate the
diagnose; they must be looked for under specific
MIL, the PCM sets a DTC P0700 ($89) to alert the
conditions that cause them. The following proce-
technician that there are DTCs in the Transmis-
dures may assist you in identifying a possible
sion. The PCM DTC ($89) must also be erased in the
intermittent problem:
PCM in order to extinguish the MIL.
• Visually inspect related wire harness connectors.
3.3.1 HARD CODE Look for broken, bent, pushed out, or corroded
terminals.
POWERTRAIN • Visually inspect the related harnesses. Look for

A diagnostic trouble code that comes back within chafed, pierced, or partially broken wire.
one cycle of the ignition key is a 9hard9 code. This • Refer to any S.T.A.R. Hotline Newsletters, Ser-
means that the problem is present when the PCM vice Information Tune ups (SITs) or Service Bul-
checks that circuit or function. Most procedures in letins that may apply.
this manual verify if the trouble code is a hard code • Use the DRBIIIt data recorder or co-pilot.
at the beginning of each test. When it is not a hard Some Transmission intermittent DTCs are
code, an 9intermittent9 test must be performed. caused by wiring or connector problems. However
Codes that are for OBDII monitors will not set intermittent Speed ratio codes are usually caused
with just the ignition key on. Comparing these to by intermittent hydraulic seal leakage in the clutch
non-emission codes, they will seem like an intermit- and/or accumulator circuits. Intermittent speed ra-
tent. These codes require a set of parameters to be tio codes can be set by intermittent speed sensor
performed (The DRBIIIt pre-test screens will help circuitry or by line noise being induced onto one or
with this for MONITOR codes), this is called a both of the speed sensor signal circuits. Problems
9TRIP9. All OBDII DTCs will be set after two or in that come and go like this are the most difficult to
some cases one trip failures, and the MIL will be diagnose, they must be looked for under the specific
turned on. These codes require three successful, no conditions that cause them.
failures, TRIPS to extinguish the MIL, followed by
40 warm-up cycles to erase the code. For further 3.3.4 STARTS SINCE SET COUNTER
explanation of TRIPS, Pre-test screens, Warm-up
cycles, and the use of the DRBIIIt, refer to the On
POWERTRAIN
Board Diagnostic training booklet #81-699-97094.
This reset counter counts the number of times the
vehicle has been started since codes were last set or
TRANSMISSION
erased. This counter will count up to 255 start
Any Diagnostic Trouble Code (DTC) that is set
counts. The number of starts helps determine when
whenever the system or component is monitored is
the trouble code actually happened. This is recorded
a HARD code. This means that the problem is there
by the PCM and can be viewed on the DRBIIIt as
every time the PCM checks that system or compo-
STARTS since set. When there are no trouble codes
nent. Some codes will set immediately at start up
stored in memory, the DRBIIIt will display 9NO
and others will require a road test under specific
TROUBLE CODES FOUND’’ and the reset counter
conditions. It must be determined if a code is
will show 9STARTS since set = XXX.’’ OBDII vehi-
repeatable (Hard) or intermittent before attempt-
cles will also display a DTC Specific or Global 9Good
ing transmission diagnosis.
Trip9 counter which will indicate the number of
9Good Trips9 since the DTC was set. After 3 consec-
3.3.2 ONE TRIP FAILURE utive 9Good Trips,9 the MIL is extinguished and the
A One Trip Failure, when read from the PCM, is good trip counter is replaced by a 9Warm Up Cycle9
a hard OBDII/EURO III code that has not matured counter. 40 Warm-Up Cycles will erase the DTC and
to the full 5 minutes. This DTC can take up to five Freeze Frame information.
minutes of problem identification before illuminat-
ing the MIL TRANSMISSION
The Starts Since Set counter counts the number
of times the vehicle has started since the most

11
bY dR.dEaDhEaD
GENERAL INFORMATION
recent DTC was set. The counter will count up to Learn. For best results, Quick Learn should be
255 starts. Note that this counter only applies to the run with the transmission sump temperature >
last code set. 90°F.
When there are no diagnostic trouble codes stored > If an unused PCM is installed on a vehicle with a
in memory, the DRBIIIt will display 9NO DTC’s HOT engine, Quick Learn will cause the PCM to
PRESENT9 and the reset counter will show report a cold calculated oil temperature. This
9STARTS SINCE CLEAR9 = XXX. requires monitoring the calculated oil tempera-
The number of starts helps determine if the ture using the DRBIIIt. If the temperature is
diagnostic trouble code is hard or intermittent. below 16° C (60° F), the transmission must be
– If the number of starts is less than 3, the code run at idle or driven in gear until it goes above
is usually a hard code. 16° C (60° F). If the temperature is above 93° C
– If the number of starts is greater than 3, it is (200° F), the transmission must cool to below 93°
considered an intermittent code. This means C (200° F).
that the engine has been started most of the > First gear is engaged in overdrive after Quick
time without the code recurring. Learn is completed. Place the vehicle in park
after performing Quick Learn.
3.3.5 TROUBLE CODE ERASURE The Quick Learn function should be performed:
A Diagnostic trouble code will be cleared from – Upon installation of a new service PCM
PCM memory if it has not reset for 40 warm-up – After replacement or rebuild of internal trans-
cycles. A warm-up cycle is defined as 9sufficient mission components or the torque converter
vehicle operation such that the coolant temperature – If one or more of the clutch volumes indexes
has risen by at least 22° C (40°F) from engine (CVI’s) contain skewed readings because of
starting and reaches a minimum temperature of abnormal conditions.
71° C (160° F). The Malfunction Indicator Lamp The Quick Learn procedure is performed with the
(MIL) will turn off after 3 good trips or when the DRBIIIt by selecting 9Transmission9 system then
DTC’s are cleared from the PCM 9Miscellaneous9 functions, then 9Quick Learn9. Fol-
low the procedure instructions displayed on the
3.3.6 QUICK LEARN DRBIIIt.
The Quick Learn function customizes adaptive To perform the Quick Learn procedure, the fol-
parameters of the PCM to the transmission Char- lowing conditions must be met.
acteristics of a vehicle. This gives the customer
improved 9as received9 shift quality compared to the NOTE: The oil temperature must be between
initial parameters stored in the PCM. 16° C (60° F) and 93° C (200° F). Above 32° C
Notes about Quick Learn Features (90° F) for best results.
The nature of the Quick Learn function requires Cycle the transmission through all gears 2-3
that certain features must be taken into consider- times immediately before performing Quick
ation. Learn.
> Quick Learn should generally not be used as a – It is imperative that the vehicle oil level set to
repair procedure unless directed by a repair or the correct level. Shift the transmission into
diagnostic procedure. If the transmission system OD with the engine running, this step will
is exhibiting a problem that you think is caused purge the air in the clutch circuits to prevent
by an invalid CVI, you should try to relearn the erroneous clutch volume values, which could
value by performing the appropriate driving ma- cause poor initial shift quality.
neuver . In most cases, if a Quick Learn makes a
vehicle shift better, the vehicle will return with – Shift the transmission to neutral.
the same problem. – The brakes must be applied.
> Before performing Quick Learn, it is imperative – The engine must be idling.
that the vehicle be shifted into OD with the – The throttle angle (TP sensor) must be less
engine running and the oil level set to the correct than 3 degrees.
level. This step will purge air from the clutch – The shift lever position must stay in neutral,
circuits to prevent erroneous clutch volume val- after shifting to neutral the engine idle speed
ues which could cause poor initial shift quality. will ramp up to 1600rpm and the DRBIIIt will
Cycle the transmission through all gears 2-3 prompt the operator to shift to OD. Do not shift
times immediately before performing Quick to OD until the engine idle speed stabilizes at
1600rpm.

12
bY dR.dEaDhEaD
 GENERAL INFORMATION
– The shift lever must stay in OD after the 9Shift The UD clutch volume is updated when doing a
to Overdrive9 prompt until the DRBIIIt indi- 4-3 or 4-2 shift. The transmission temperature must
cates the procedure is complete. be above 43 C (110° F). The clutch volume should be
between 24 and 70.
NOTE: The above conditions must be
maintained during the procedure to keep the 3.3.9 NO START INFORMATION
procedure from being aborted.
(POWERTRAIN)
NOTE: After the Quick Learn Procedure is
complete, the vehicle should be drive learned IMPORTANT NOTE:
per the Drive Learn Procedure If the Powertrain Control Module has been pro-
grammed, a DTC will set in the ABS and Air Bag
3.3.7 EATX DTC EVENT DATA modules. In addition, if the vehicle is equipped with
a Sentry Key Immobilizer Module (SKIM), Secret
EATX DTC EVENT DATA can be used as a
Key data must be updated to enable starting.
diagnostic aid when experiencing Electronic Trans-
missions with intermittent problems. When a Diag- FOR ABS AND AIR BAG SYSTEMS:
nostic Trouble Code (DTC) is set, the vehicles EATX 1. Enter correct VIN and Mileage in PCM.
inputs are stored in the controller memory and are 2. Erase codes in ABS and Air Bag modules.
retrievable with the DRBIIIt. This information can
be helpful when a DTC can not be duplicated. FOR SKIM THEFT ALARM:
The EATX DTC EVENT DATA is located in the 1. Connect the DRBIIIt to the data link connec-
DRBIIIt, under the Transmission system menu, in tor.
the sub-screen Miscellaneous. It is a good practice 2. Go to Theft Alarm, SKIM, Misc. and place the
to document the EATX DTC EVENT DATA before SKIM in secured access mode, by using the appro-
beginning any diagnostic or service procedure. priate PIN code for this vehicle.
A thorough understanding of how the transmis- 3. Select Update the Secret Key data, data will be
sion works is beneficial in order to interpret the transferred from the SKIM to the PCM (This is
data correctly. These skills are necessary in order to required to allow the vehicle to start with the new
avoid an incorrect diagnosis. A MASTERTECH PCM).
video and reference book was produced in January 4. If three attempts are made to enter secured
2002 that explains many of the features of the access mode using the incorrect PIN, secured access
EATX DTC EVENT DATA with several examples on mode will be locked out for one hour. To exit this
how to interpret the information and suggested lock out mode, leave the ignition key in the Run/
training material to help understand all the specif- Start position for one hour. Ensure all accessories
ics. are turned off. Also monitor the battery state and
EATX DTC EVENT DATA can only be erased by: connect a battery charger if necessary.
1. Disconnecting the battery. After reading Section 3.0 (System Description
2. Performing a DRBIIIt QUICK LEARN proce- and Functional Operation), you should have a bet-
dure. ter understanding of the theory and operation of the
3. Reprogramming the EATX controller. on-board diagnostics, and how this relates to the
Erasing Transmission DTCs does not clear the diagnosis of a vehicle that may have a driveability-
EATX DTC EVENT DATA. related symptom or complaint.

3.3.8 CLUTCH VOLUMES 3.4 USING THE DRBIIIT

The LR clutch volume is updated when doing a
Refer to the DRBIIIt user’s guide for instructions
2-1 or 3-1 coast down shift. The transmission tem-
and assistance with reading trouble codes, erasing
perature must be between 21-49 C (70-120° F). The
trouble codes, and other DRBIIIt functions.
clutch volume should be between 35 and 83.
The 2/4 clutch volume is updated when doing a
1-2 shift. The transmission temperature must be 3.5 DRBIIIT ERROR MESSAGES AND
above 43 C (110° F). The clutch volume should be BLANK SCREEN
between 20 and 77.
The OD clutch volume is updated when doing a Under normal operation, the DRBIIIt will dis-
2-3 shift. The transmission temperature must be play one of only two error messages:
above 43 C (110° F). The clutch volume should be – User-Requested WARM Boot by pressing
between 40 and 150. MORE and NO at the same time.

13
bY dR.dEaDhEaD
GENERAL INFORMATION
ver: 2.29
date: 1 oct 93
file: key_itf.cc
date: Jan 12 1994
line: 544
err: 0x1User-Requested WARM Boot
Press MORE to switch between this display
and the application screen.
Press F4 when done noting information.
or User Requested COLD Boot by pressing MORE
YES at the same time.
ver: 2.29
date: 1 oct 99
file: key HND1.CC
date: Mar 8 2000
line: 1297
err: 0x1
User-Requested COLD Boot 3.6 TRANSMISSION SIMULATOR (MILLER
Press MORE to switch between this display
and the application screen. TOOL # 8333) AND ELECTRONIC
Press F4 when done noting information. TRANSMISSION ADAPTER KIT
If the DRBIIIt should display any other error
(MILLER TOOL #8333-1A)
message, record the entire display and call the Star
Center. NOTE: Remove the starter Relay when using
the transmission simulator
3.5.1 DRBIIIT DOES NOT POWER UP *Failure to remove the Starter Relay can
If the LED’s do not light or no sound is emitted at cause a PCM - No Response condition.
start up, check for loose cable connections or a bad *The removal of the Starter Relay will also
cable. Check the vehicle battery voltage (data link prevent the engine from starting in gear.
connector cavity 16). Check for proper ground con- *The Transmission Simulator will not
nection at DLC cavity. A minimum of 11 volts is
accurately diagnose intermittent faults.
required to adequately power the DRBIIIt.
The transmission simulator, simply put, is an
If all connections are proper between the DRBI-
electronic device that simulates the electronic func-
IIt and the vehicle or other devices, and the vehicle
tions of any EATX or NGC controlled transmission.
battery is fully charged, an inoperative DRBIIIt
The Simulators basic function is to aid the techni-
may be the result of a faulty cable or vehicle wiring.
cian in determining if an internal transmission
For a blank screen, refer to the appropriate body
problem exists or if the problem resides in the
diagnostics manual.
vehicle wiring or control module. It is only useful for
electrical problems. It will not aid in the diagnosis
3.5.2 DISPLAY IS NOT VISIBLE of a failed mechanical component, but it can tell you
Low temperatures will affect the visibility of the that the control module and wiring are working
display. Adjust the contrast to compensate for this properly and that the problem is internal.
condition. The ignition switch should be in the lock position
before attempting to install the simulator. Follow
3.5.3 SOME DISPLAY ITEMS READ (___( all instructions included with the simulator. If the
This is caused by scrolling the DRBIIIt display a feedback from the simulator is in doubt, you can
single line up or down. The line which was scrolled verify it’s operation by installing it on a known good
onto the screen might read 9___9. Use the page down vehicle. A 9known good vehicle9 would be defined as
or page up function to display the information. a vehicle that does not set any DTC’s and drives and
shifts as expected.
One important point to remember is that the
Simulator receives it’s power from the Trans Relay
Output circuit. If the transmission system is in
Limp-in (Relay open), the simulator will not oper-
ate. This is not really an indication of a problem,

14
bY dR.dEaDhEaD
 GENERAL INFORMATION
but an additional symptom. If the simulator does important that accurate shift lever position data is
not power up (9P9 led lit), this is an indication that available to the PCM. The accuracy of any DTC
the problem is still present with the simulator found in memory is doubtful unless the Shift Lever
hooked up. This indicates that the problem is in the Test, performed on the DRBIIIt Scan Tool, passes
wiring or control module and not the transmission. without failure.
Miller Tool # 8333-1A consists of the adapter
cables and overlay necessary to adapt the simulator 4.2.3 SEVICING SUB-ASSEMBLIES
to TE/AE/LE/RLE transmissions. Some components of the powertrain system are
intended to be serviced in assembly only. Attempt-
4.0 DISCLAIMERS, SAFETY, ing to remove or repair certain system sub-
components may result in personal injury and/or
WARNINGS improper system operation. Only those components
with approved repair and installation procedures in
the service manual should be serviced.
4.1 DISCLAIMERS
All information, illustrations, and specifications 4.2.4 DRBIIIT SAFETY INFORMATION
contained in this manual are based on the latest
information available at the time of publication. WARNING: EXCEEDING THE LIMITS OF THE
The right is reserved to make changes at any time DRBIIIT MULTIMETER IS DANGEROUS. IT
without notice. CAN EXPOSE YOU TO SERIOUS INJURY.
CAREFULLY READ AND UNDERSTAND THE
4.2 SAFETY CAUTIONS AND THE SPECIFICATION
LIMITS.
Follow the vehicle manufacturer’s service specifi-
4.2.1 TECHNICIAN SAFETY INFORMATION cations at all times.
• Do not use the DRBIIIt if it has been damaged.
WARNING: ENGINES PRODUCE CARBON
MONOXIDE THAT IS ODORLESS, CAUSES • Do not use the test leads if the insulation is
SLOWER REACTION TIME, AND CAN LEAD damaged or if metal is exposed.
TO SERIOUS INJURY. WHEN THE ENGINE IS • To avoid electrical shock, do not touch the test
OPERATING, KEEP SERVICE AREAS WELL leads, tips, or the circuit being tested.
VENTILATED OR ATTACH THE VEHICLE • Choose the proper range and function for the
EXHAUST SYSTEM TO THE SHOP EXHAUST measurement. Do not try voltage or current mea-
REMOVAL SYSTEM. surements that may exceed the rated capacity.
Set the parking brake and block the wheels before • Do not exceed the limits shown in the table below:
testing or repairing the vehicle. It is especially
important to block the wheels on front-wheel drive Function Input Limit
vehicles; the parking brake does not hold the drive
Volts 0 - 500 peak volts AC
wheels.
0 - 500 volts DC
When servicing a vehicle, always wear eye pro-
tection, and remove any metal jewelry such as Ohms (resistance)* 0 - 1.12 megohms
watchbands or bracelets that might make an inad-
Frequency Measured 0 - 10 kHz
vertent electrical contact.
Frequency Generated
When diagnosing a powertrain system problem,
it is important to follow approved procedures where Temperature - 50 - 600°C
applicable. These procedures can be found in the - 58 - 1100°F
service manual procedures. Following these proce- * Ohms cannot be measured if voltage is present.
dures is very important to the safety of individuals Ohms can be measured only in a non-powered
performing diagnostic tests. circuit.
• Voltage between any terminal and ground must
4.2.2 VEHICLE PREPARATION FOR not exceed 500v DC or 500v peak AC.
TESTING • Use caution when measuring voltage above 25v
Make sure the vehicle being tested has a fully DC or 25v AC.
charged battery. If it does not, false diagnostic • A 10A fuse or circuit breaker must protect the
DTC’s or error messages may occur. It is extremely circuit being tested.

15
bY dR.dEaDhEaD
GENERAL INFORMATION
• Use the low current shunt to measure circuits up 4.3.3 ROAD TESTING A COMPLAINT
to 10A. Use the high current clamp to measure
circuits exceeding 10A. VEHCILE (TRANSMISSION)
• When testing for the presence of voltage or cur- Some complaints will require a test drive as part
rent, make sure the meter is functioning cor- of the repair verification procedure. The purpose of
rectly. Take a reading of a known voltage or the test drive is to try to duplicate the diagnostic
current before accepting a zero reading. DTC or symptom condition.
• When measuring current, connect the meter in CAUTION: Before road testing a vehicle, be
series with the load. sure that all components are reassembled.
• Disconnect the live test lead before disconnecting During the test drive, do not try to read
the common test lead. DRBIIIT screen while in motion. Do not hang
• When using the meter function, keep the the DRBIIIT from the rear view mirror or
DRBIIIt away from spark plug or coil wires to operate it yourself. Have an assistant
avoid measuring error from outside interference. available to operate the DRBIIIT.
Road testing is an essential step in the diagnostic
4.3 WARNINGS AND CAUTIONS process that must not be overlooked. Along with the
diagnostic information obtained from the DRBIIIt
Scan Tool and the original customer concern, the
4.3.1 ROAD TEST WARNINGS road test helps verify the problem was current and
Some complaints will require a test drive as part any repairs performed, fixed the vehicle correctly.
of the repair verification procedure. The purpose of Always operate and observe the vehicle under ac-
the test drive is to try to duplicate the diagnostic tual driving conditions. Just as important as the
code or symptom condition. road test is, there are preliminary inspections that
should be performed prior to the road test. Always
CAUTION: Before road testing a vehicle, be check the fluid level and condition before taking the
sure that all components are reassembled. vehicle on a road test. Determine if the incorrect
During the test drive, do not try to read the fluid is being used, improper fluid will result in
DRBIIIT screen while in motion. Do not hang erratic transmission operation.
the DRBIIIT from the rear view mirror or Some of the conditions of incorrect fluid level are
operate it yourself. Have an assistant as follows:
available to operate the DRBIIIT. • Delayed engagement
• Poor shifting or erratic shifting
4.3.2 VEHICLE DAMAGE WARNINGS • Excessive noise
Before disconnecting any control module, make
• Overheating
sure the ignition is 9lock9 position. Failure to do so
The next step is to verify that the shift linkage is
could damage the module.
correctly adjusted. If the shift linkage is incorrectly
When testing voltage or continuity at any control
adjusted, a number of complaints can result.
module, use the Miller tool #8815 (not the wire end
The PCM monitors the Shift Lever Position (SLP)
or terminal) in the connector. Do not probe a wire
Sensor continuously. If the linkage is incorrectly
through the insulation: this will damage the wire
adjusted, the PCM will sense a shift lever position
and eventually cause the wire to fail because of
that is not correct for the gear chosen by the driver.
corrosion.
This may cause a DTC to be set.
Be careful when performing electrical tests so as
The following complaints may also be the result
to prevent accidental shorting of terminals. Such
of an incorrectly adjusted or worn linkage:
mistakes can damage fuses or components. Also, a
• Delayed clutch engagement
second DTC could be set, making diagnosis of the
original problem more difficult. • Erratic shifts
When replacing a blown fuse, it is important to • Vehicle will drive in neutral
use only a fuse having the correct amperage rating. • Engine will not crank in park or neutral
The use of a fuse with a rating other than indicated
• Gear shift linkage will be able to be shifted
may result in a dangerous electrical system over-
load. If a properly rated fuse continues to blow, it without the key in the ignition
indicates a problem in the circuit that must be • Not able to remove the ignition key in park
corrected. • Parking pawl will not engage properly
The shift linkage should also be adjusted when
replacing the Transmission, repairing the valve

16
bY dR.dEaDhEaD
 GENERAL INFORMATION
body, or when repairing any component between the 12 volt test light minimum 25 ohms resistance
shift lever and the Transmission. with probe #6801
Some questions to ask yourself when performing
the road test are as follows: CAUTION: A 12 volt test light should not be
• Is the complaint or concern what you think the used for the following circuits, damage to the
problem is, based on the drivers description of the powertrain controller will occur.
problem? • 5-volt Supply
• Is the Transmission operating normally, or is • J1850 PCI Bus
there a real problem? • CCD Bus
• When does the problem occur? • PCI Bus
• Is the problem only in one gear range? • CKP Sensor Signal
• What temperature does the problem occur? • CMP Sensor Signal
• Does the vehicle have to sit over night for the • Vehicle Speed Sensor Signal
problem to occur?
• O2 Sensor Signal
• Does the transmission go into Limp-in mode?

4.3.4 ELECTRONIC PINION FACTOR 6.0 ACRONYMS

WARNINGS (IF APPLICABLE) A/C Air Conditioning
The pinion factor must be set when replacing the
PCM. Note: The pinion factor is a fixed number and ABS Anti-lock Brake System
cannot be changed or updated in some vehicle ASD Re- Auto Shutdown Relay
applications. If the pinion factor is not set or incor- lay
rectly set, any speed related functions will not
operate correctly i.e. speedometer, speed control, APPS Accelerator Pedal Position Sensor
rolling door locks, other control modules will be
Baro Barometric Pressure
affected that depend on speed information.
BCM Body Control Module
4.3.5 SERVICE BULLETINS AND RECALLS
BTS Battery Temperature Sensor
Always perform all Safety Recalls and Service
Bulletins that are applicable to the problem. Under CAA Clean Air Act
the provisions of the warranty.
CAB Controller Antilock Brakes
CARB California Air Resources Board
5.0 REQUIRED TOOLS AND
EQUIPMENT CCD Chrysler Collision Detection Bus
BUS
DRBIIIt (diagnostic read-out box) scan tool -
CKP Crankshaft Position Sensor
must use the latest release level.
Sensor
Diagnostic Pinout Box #8815
Evaporative Emissions Leak Detector #8404 CKT Circuit
Terminal Removal tool #3638
Fuel filler adapter #8382 CMP Camshaft Position Sensor
Fuel pressure adapter (C-6631) or #6539 Sensor
Fuel pressure kit (C-4799-B) or #5069 CM840 Cummins Engine controller
Fuel pressure kit #8978
Fuel release hose (C-4799-1) CO Carbon Monoxide
Jumper wires CVI Clutch Volume Index
Ohmmeter
Oscilloscope DCP So- Duty-Cycle Purge Solenoid
Pressure gauge 0-2068 kPa (0-300 PSI) lenoid
Transmission simulator #8833
DLC Data Link Connector
Electronic Transmission Adapter Kit (Miller #
8333-1A) DRBIIIt Diagnostic Readout Box - 3rd Gen-
Vacuum gauge eration
Voltmeter

17
bY dR.dEaDhEaD
GENERAL INFORMATION
DTC Diagnostic Trouble Code LDP Leak Detection Pump
DVOM Digital Volt Ohm Meter LED Light Emitting Diode
EATX Electronic Automatic Transmission LPS Line Pressure Sensor
Controller
LR Low/reverse Clutch
EC European Community
LSIACV Linear Solenoid Idle Air Control
ECT Engine Coolant Temperature Sensor Valve
Sensor
MAF Mass Air flow
EE- Electrically Erasable Programmable
MAP Manifold Absolute Pressure Sensor
PROM Read Only Memory
Sensor
EGR Exhaust Gas Recirculation Valve
MDS2t Mopar Diagnostic System 2nd Gen-
Valve
eration
EMCC Electronically Modulated Converter
MIL Malfunction Indicator Lamp
Clutch
MS Multi Select
EMI Electro-Magnetic Interference
MTV Manifold Tuning Valve
EOBD European OBD (based upon Euro
Stage III) NGC Next Generation Controller
EPA Environmental Protection Agency NTC Negative Temperature Coefficient
EPP Engine Position Pulse NVLD Natural Vacuum Leak Detection
ETC Electronic Throttle Control O2 Sen- Oxygen Sensor
sor
EU European Union
O2S Oxygen Sensor
EVAP Evaporative Emission System
OBD I On Board Diagnostics 1st Genera-
EVR Electronic Voltage Regulator
tion
EWMA Exponentially Weighted Moving Av-
OBD II On-Board Diagnostics 2nd Genera-
erage
tion
FEMCC Fully Electronically Modulated Con-
OD Overdrive Clutch
verter Clutch
ORVR On-Board Refueling Vapor Recovery
FTP Federal Test Procedure
OSS Output Speed Sensor
FSS Fan Speed signal
PCI BUS Programmable Communications In-
HC Hydrocarbons
terface BUS (J1850)
HO2S Heated Oxygen Sensor
PCM Powertrain Control Module
Genera- Previously called 9alternator9
PCS Pressure Control Solenoid
tor
PCV Positive Crankcase Ventilation
IAC Mo- Idle Air Control Motor
tor PDC Power Distribution Center
IAT Sen- Intake Air Temperature Sensor PEMCC Partial Electronically Modulated
sor Converter Clutch
IOD Ignition off draw PEP Peripheral Expansion Port
IRT Intelligent Recovery Timer P/N Park/Neutral
ISS Input Speed Sensor PPS Proportional Purge Solenoid
I/M Inspection and Maintenance Testing PS Power Steering
JTEC Jeep/Truck Engine Controller

18
bY dR.dEaDhEaD
 GENERAL INFORMATION
PSP Power Steering Pressure (Switch) TRD Torque Reduction
PTC Positive Temperature Coefficient TRS Transmission Range Sensor
PWM Pulse-Width Modulation TTS Transmission Temperature Sensor
RAM Random Access Memory UD Underdrive Clutch
REV Reverse Clutch VSS Vehicle Speed Signal
RFI Radio Frequency Interference WOT Wide Open Throttle
RKE Remote Keyless Entry 2/4 2nd and 4th gear Clutch or Pres-
sure Switch
RPM Revolutions Per Minute
2C 2nd Clutch
SAE Society of Automotive Engineers
4C 4th Clutch
SBEC Single Board Engine Controller
SCW Similar Conditions Window 6.1 DEFINITIONS
SKIM Sentry Key Immobilizer Module OBDII/EURO III Trip - A vehicle start and drive
cycle such that all once per trip diagnostic monitors
SRV Short Runner Valve
have run.
SSV Solenoid Switch Valve Key Start - A vehicle start and run cycle of at least
20 seconds.
SW Switch Warm-up Cycle - A vehicle start and run cycle
TCC Torque Converter Clutch such that the engine coolant must rise to at least
71 C (160° F) and must rise by at least 22 C (40° F)
TCCM Transfer Case Control Module from initial start up. To count as a warm-up cycle,
no DTC’s may occur during the cycle.
TDC Top Dead Center
TP Throttle Position Sensor

19
bY dR.dEaDhEaD
 NOTES

20
bY dR.dEaDhEaD
 7.0
DIAGNOSTIC INFORMATION AND
PROCEDURES

21
bY dR.dEaDhEaD
COMMUNICATION

Symptom:
*NO RESPONSE FROM PCM (PCI BUS) - NGC

POSSIBLE CAUSES
PCM PCI NO RESPONSE
POWERTRAIN CONTROL MODULE
PCI BUS CIRCUIT OPEN

TEST ACTION APPLICABILITY

1 Turn the ignition on. All
NOTE: As soon as one or more module communicates with the DRB, answer
the question.
With the DRB, enter Body then Electro/Mechanical Cluster (MIC).
With the DRB, enter Passive Restraints then Airbag.
Were you able to establish communications with any of the modules?

Yes → Go To 2
No → Refer to symptom PCI Bus Communication Failure in the Com-
munications category.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2 With the DRB read the Powertrain DTC’s. This is to ensure power and grounds to the All
PCM are operational.
NOTE: If the DRB will not read PCM DTC’s, follow the NO RESPONSE TO
PCM (PCM SCI only) symptom path.
Turn the ignition off.
Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
With the DRBIIIt select Pep Module Tools.
Select lab scope.
Select Live Data.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the appropriate terminal of special tool #8815.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

Yes → Replace and program the Powertrain Control Module in accor-

dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Repair the PCI Bus circuit for an open.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

22
bY dR.dEaDhEaD
 COMMUNICATION

Symptom:
*NO RESPONSE FROM PCM (PCM SCI ONLY) - NGC

POSSIBLE CAUSES
CHECK PCM POWERS AND GROUNDS
CONTROLLER ANTILOCK BRAKE
SCI TRANSMIT CIRCUIT SHORTED TO VOLTAGE
SCI RECEIVE CIRCUIT SHORTED TO VOLTAGE
SCI CIRCUITS SHORTED TOGETHER
SCI TRANSMIT CIRCUIT SHORTED TO GROUND
SCI RECEIVE CIRCUIT SHORTED TO GROUND
SCI RECEIVE CIRCUIT OPEN
SCI TRANSMIT CIRCUIT OPEN
POWERTRAIN CONTROL MODULE

TEST ACTION APPLICABILITY

1 Perform the symptom Checking PCM Power and Ground Circuits in the Driveability All
category.
NOTE: With the DRBIIIt in the generic scan tool mode, attempt to commu-
nicate with the PCM.
NOTE: If the DRBIIIt can communicate with the PCM in the generic scan
tool mode, it may not be necessary to perform this step.
Did the vehicle pass this test?
Yes → Go To 2

No → Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2 Turn the ignition off. All

Disconnect the PCM harness connectors.
Disconnect the DRB from the DLC.
Measure the resistance between ground and the SCI Transmit circuit at the DLC (cav
7).
Is the resistance below 5.0 ohms?

Yes → Go To 3

No → Go To 4

23
bY dR.dEaDhEaD
COMMUNICATION

*NO RESPONSE FROM PCM (PCM SCI ONLY) - NGC — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the CAB harness connector (if equipped).
NOTE: If vehicle is not equipped with antilock brakes, answer yes to the
question.
Measure the resistance between ground and the SCI Transmit circuit at the DLC (cav
7).
Is the resistance below 5.0 ohms?

Yes → Repair the SCI Transmit circuit for a short to ground.

Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Replace the Controller Antilock Brake in accordance with the
service information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

4 Turn the ignition off. All

Disconnect the DRB from the DLC.
Disconnect the PCM harness connectors.
Disconnect the CAB harness connector (if equipped).
Turn the ignition on.
Measure the voltage of the SCI Transmit circuit at the DLC (cav 7).
Is the voltage above 1.0 volt?
Yes → Repair the SCI Transmit circuit for a short to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Go To 5

5 Turn the ignition off. All

Disconnect the DRB from the DLC.
Disconnect the PCM harness connectors.
Turn the ignition on.
Measure the voltage of the SCI Receive circuit at the DLC (cav 12).
Is the voltage above 1.0 volt?

Yes → Repair the SCI Receive circuit for a short to voltage.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Go To 6

6 Turn the ignition off. All

Disconnect the DRB from the DLC.
Disconnect the PCM harness connectors.
Measure the resistance between the SCI Transmit circuit and the SCI Receive circuit
at the DLC (cavs 7 and 12).
Is the resistance below 5.0 ohms?

Yes → Repair the short between the SCI Transmit and the SCI Receive
circuits.
Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Go To 7

24
bY dR.dEaDhEaD
 COMMUNICATION

*NO RESPONSE FROM PCM (PCM SCI ONLY) - NGC — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off. All
Disconnect the PCM harness connectors.
Disconnect the DRB from the DLC.
Measure the resistance between ground and the SCI Receive circuit at the DLC (cav
12).
Is the resistance below 5.0 ohms?

Yes → Repair the SCI Receive circuit for a short to ground.

Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Go To 8

8 Turn the ignition off. All

Disconnect the PCM harness connectors.
Disconnect the DRB from the DLC.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the SCI Receive circuit from the DLC (cav 12) to the
appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 9
No → Repair the SCI Receive circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

9 Turn the ignition off. All

Disconnect the PCM harness connectors.
Disconnect the DRB from the DLC.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the SCI Transmit circuit from the DLC (cav 7) to the
appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 10

No → Repair the SCI Transmit circuit for an open.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

10 If there are no possible causes remaining, view repair. All

Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

25
bY dR.dEaDhEaD
COMMUNICATION

Symptom:
*NO RESPONSE FROM SENTRY KEY IMMOBILIZER MODULE

POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE INSTRUMENT CLUSTER
GROUND CIRCUIT OPEN
FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
FUSED B(+) CIRCUIT OPEN
OPEN PCI BUS CIRCUIT
SENTRY KEY IMMOBILIZER MODULE

TEST ACTION APPLICABILITY

1 Turn the ignition on. All
With the DRB, enter Body then Electro/Mech Cluster.
Was the DRB able to I/D or communicate with the Instrument Cluster?
Yes → Go To 2

No → Refer to the symptom list for problems related to no communica-

tion with the Instrument Cluster.
Perform SKIS VERIFICATION.

2 Turn the ignition off. All

Disconnect the SKIM harness connector.
Using a 12-volt test light connected to 12-volts, probe the ground circuit.
Is the test light illuminated?
Yes → Go To 3
No → Repair the ground circuit for an open.
Perform SKIS VERIFICATION.

3 Turn the ignition off. All

Disconnect the SKIM harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused Ignition Switch
Output circuit.
Is the test light illuminated?

Yes → Go To 4
No → Repair the Fused Ignition Switch Output circuit for an open.
Perform SKIS VERIFICATION.

4 Turn the ignition off. All

Disconnect the SKIM harness connector.
Using a 12-volt test light connected to ground, probe the Fused B(+) circuit.
Is the test light illuminated?
Yes → Go To 5

No → Check the Fuse in the Fuse Block for an open. Refer to the wiring
diagrams. If OK, repair the Fused B+ circuit for an open.
Perform SKIS VERIFICATION.

26
bY dR.dEaDhEaD
 COMMUNICATION

*NO RESPONSE FROM SENTRY KEY IMMOBILIZER MODULE —

Continued
TEST ACTION APPLICABILITY
5 Note: Ensure there is PCI Bus communication with other modules on the All
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the SKIM harness connector.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
With the DRBIIIt select Pep Module Tools.
Select lab scope.
Select Live Data.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the SKIM connector.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

Yes → Go To 6
No → Repair the PCI Bus circuit for an open.
Perform SKIS VERIFICATION.

6 If there are no possible causes remaining, view repair. All

Repair
Replace and program the Sentry Key Immobilizer Module in
accordance with the Service Information.
Perform SKIS VERIFICATION.

27
bY dR.dEaDhEaD
COMMUNICATION

Symptom:
*NO RESPONSE FROM TRANSMISSION CONTROL MODULE - NGC

POSSIBLE CAUSES
NO RESPONSE FROM TRANSMISSION CONTROL MODULE
FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
FUSED B(+) CIRCUIT OPEN
GROUND CIRCUIT(S) OPEN
PCI BUS CIRCUIT OPEN
POWERTRAIN CONTROL MODULE

TEST ACTION APPLICABILITY

1 Turn the ignition on. All
Note: As soon as one or more module communicates with the DRB, answer
the question.
With the DRB, attempt to communicate with the Instrument Cluster.
With the DRB, attempt to communicate with the Airbag Control Module.
Was the DRB able to I/D or establish communications with both of the modules?
Yes → Go To 2
No → Refer to the Communications category and perform the appropri-
ate symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

2 Turn the ignition off. All

Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe each Fused Ignition Switch
Output circuit (cavs 11 and 12) in the appropriate terminal of special tool #8815.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Is the test light illuminated for both circuits?
Yes → Go To 3

No → Repair the Fused Ignition Switch Output circuit for an open or

short. Refer to the wiring diagrams located in the Service Infor-
mation.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

28
bY dR.dEaDhEaD
 COMMUNICATION

*NO RESPONSE FROM TRANSMISSION CONTROL MODULE - NGC —

Continued
TEST ACTION APPLICABILITY
3 Turn the ignition off. All
Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Using a 12-volt test light connected to ground, probe the Fused B(+) circuit in the
appropriate terminal of special tool #8815.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Is the test light illuminated?

Yes → Go To 4

No → Repair the Fused B(+) circuit for an open. Refer to the wiring
diagrams located in the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

4 Turn the ignition off. All

Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Using a 12-volt test light connected to 12-volts, probe each ground circuit in the
appropriate terminal of special tool #8815.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Is the light illuminated at all ground circuits?

Yes → Go To 5
No → Repair the Ground circuit(s) for an open. Check the main ground
connection to engine block and/or chassis. Refer to the wiring
diagrams located in the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

29
bY dR.dEaDhEaD
COMMUNICATION

*NO RESPONSE FROM TRANSMISSION CONTROL MODULE - NGC —

Continued
TEST ACTION APPLICABILITY
5 Note: Ensure there is PCI Bus communication with other modules on the All
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
With the DRBIIIt select Pep Module Tools.
Select lab scope.
Select Live Data.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the appropriate terminal of special tool #8815.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?
Yes → Go To 6
No → Repair the PCI Bus circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module in accor-
dance with the service information. WITH THE DRBIIIt PER-
FORM QUICK LEARN AND REPROGRAM PINION FACTOR.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

30
bY dR.dEaDhEaD
 COMMUNICATION

Symptom:
*PCI BUS COMMUNICATION FAILURE

POSSIBLE CAUSES
WIRING HARNESS INTERMITTENT
OPEN PCI BUS CIRCUIT AT THE DATA LINK CONNECTOR (DLC)
PCI BUS CIRCUIT SHORTED TO VOLTAGE
MODULE SHORT TO VOLTAGE
PCI BUS CIRCUIT SHORTED TO GROUND
MODULE SHORT TO GROUND

TEST ACTION APPLICABILITY

1 Note: Determine which modules this vehicle is equipped with before begin- All
ning.
Note: When attempting to communicate with any of the modules on this
vehicle, the DRB will display 1 of 2 different communication errors: a NO
RESPONSE message or a BUS +/- SIGNALS OPEN message.
Turn the ignition on.
Using the DRB, attempt to communicate with the following control modules:
Airbag Control Module
SKIM (SENTRY KEY IMMOBILIZER)
MIC (INSTRUMENT CLUSTER)
Was the DRBIIIt able to communicate with one or more Module(s)?

Yes → Go To 2
No → Go To 3

2 Turn the ignition off. All

Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
Note: Visually inspect the related wire harness connectors. Look for broken,
bent, pushed out, or corroded terminals.
Note: If the DRB can not communicate with a single module, refer to the
category list for the related symptom.
Were any problems found?

Yes → Repair wiring harness/connectors as necessary.

Perform BODY VERIFICATION TEST - VER 1.

No → Test Complete.

31
bY dR.dEaDhEaD
COMMUNICATION

*PCI BUS COMMUNICATION FAILURE — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Disconnect the DRB from the Data Link Connector (DLC).
Disconnect the negative battery cable.
Measure the resistance of the PCI Bus circuit between the Data Link Connector
(DLC) and the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 4

No → Repair the PCI Bus circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

4 NOTE: Reconnect the PCM harness connector and the negative battery All
cable.
Turn the ignition on.
Measure the voltage of the PCI Bus circuit at the Data Link Connector (DLC).
Is the voltage above 7.0 volts?
Yes → Go To 5

No → Go To 6

5 Turn the ignition off. All

Using a voltmeter, connect one end to the PCI Bus circuit at the DLC, and the other
end to ground.
Note: When performing the next step turn the ignition off (wait one minute)
before disconnecting any module. When the module is disconnected turn
the ignition on to check for a short to voltage.
Turn the ignition on.
While monitoring the voltmeter, disconnect each module the vehicle is equipped with
one at a time.
Is the voltage steadily above 7.0 volts with all the modules disconnected?
Yes → Repair the PCI Bus circuit for a short to voltage.
Perform BODY VERIFICATION TEST - VER 1.

No → Replace the module that when disconnected the short to voltage

was eliminated.
Perform BODY VERIFICATION TEST - VER 1.

32
bY dR.dEaDhEaD
 COMMUNICATION

*PCI BUS COMMUNICATION FAILURE — Continued

TEST ACTION APPLICABILITY

6 Turn the ignition off. All
Disconnect the negative battery cable.
Using a ohmmeter, connect one end to the PCI Bus circuit at the DLC, and the other
end to ground.
While monitoring the ohmmeter, disconnect each module the vehicle is equipped with
one at a time.
NOTE: Total bus resistance to ground thru all of the modules is typically
between 350 to 1000 ohms. The more modules on the bus, the lower the total
bus resistance will be.
Is the resistance below 150.0 ohms with all the modules disconnected?

Yes → Repair the PCI Bus circuit for a short to ground.

Perform BODY VERIFICATION TEST - VER 1.

No → Replace the module that when disconnected the short to ground

was eliminated.
Perform BODY VERIFICATION TEST - VER 1.

33
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
INTERMITTENT CONDITION

POSSIBLE CAUSES
INTERMITTENT CONDITION

TEST ACTION APPLICABILITY

1 NOTE: The conditions that set the DTC are not present at this time. The All
following list may help in identifying the intermittent condition.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Refer to any Technical Service Bulletins (TSBs) that may apply.
Review the DRB Freeze Frame information. If possible, try to duplicate the
conditions under which the DTC set.
With the engine running at normal operating temperature, monitor the DRBIIIt
parameters related to the DTC while wiggling the related wire harness. Look for
parameter values to change and/or a DTC to set.
Turn the ignition off.
Visually inspect the related wire harness. Disconnect all the related harness
connectors. Look for any chafed, pierced, pinched, partially broken wires and broken,
bent, pushed out, or corroded terminals.
Perform a voltage drop test on the related circuits between the suspected faulty
component and the PCM.
CAUTION: NEVER PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Inspect and clean all PCM, engine, and chassis grounds that are related to the most
current DTC.
If numerous trouble codes were set, use a wire schematic and look for any common
ground or supply circuits.
For any Relay DTCs, actuate the Relay with the DRBIIIt and wiggle the related wire
harness to try to interrupt the actuation.
For intermittent Evaporative Emission trouble codes perform a visual and physical
inspection of the related parts including hoses and the Fuel Filler cap.
For intermittent Misfire DTC’s check for restrictions in the Intake and Exhaust
system, proper installation of Sensors, vacuum leaks, and binding components that
are run by the accessory drive belt.
Use the DRBIIIt to perform a System Test if one applies to failing component.
A co-pilot, data recorder, and/or lab scope should be used to help diagnose intermit-
tent conditions.
Were any problems found during the above inspections?
Yes → Repair as necessary
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Test Complete.

34
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT

When Monitored and Set Condition:

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT

When Monitored: Engine cranking and Engine running
Set Condition: Powertrain Control Module detects an error when the camshaft position is
out of phase with the crankshaft position.

POSSIBLE CAUSES
INTERMITTENT CONDITION
CMP WIRE HARNESS INSPECTION
TONE WHEEL/PULSE RING INSPECTION
INTERMITTENT CMP SIGNAL
CKP WIRE HARNESS INSPECTION
TONE WHEEL/PULSE RING INSPECTION
INTERMITTENT CKP SIGNAL
CAMSHAFT POSITION SENSOR
CRANKSHAFT POSITION SENSOR

TEST ACTION APPLICABILITY

1 WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A All
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
With the DRBIIIt, erase DTCs.
Start the engine and run until operating temp is reached. (Closed Loop)
If the DTC does not reset it may be necessary to test drive the vehicle.
Does the P0016 reset?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

35
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT — Continued

TEST ACTION APPLICABILITY

2 Turn the ignition off. All
With the DRBIIIt lab scope probe and the Miller special tool #6801, backprobe the
(K44) CMP Signal circuit at the CMP harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Start the engine.
Observe the lab scope screen.
Are there any irregular or missing signals?

Yes → Go To 3

No → Go To 6

3 Turn the ignition off. All

Visually inspect the related wire harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wire harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Make sure the Crankshaft Position Sensor and the Camshaft Position Sensor are
properly installed and the mounting bolt(s) are torqued to the correct specification.
Refer to any TSBs that may apply.
Were any of the above conditions present?
Yes → Repair as necessary
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Remove the Camshaft Position Sensor. All

Inspect the Tone Wheel/Pulse Ring for damage, foreign material, or excessive
movement.
Were any problems found?

Yes → Repair or replace the Tone Wheel/Pulse Ring as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 If there are no possible causes remaining, view repair. All

Repair
Replace the Camshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

36
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT — Continued

TEST ACTION APPLICABILITY

6 Turn the ignition off. All
Remove the lab scope probe.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
With the DRBIIIt, erase DTCs.
Start the engine.
Gently tap on the Cam Position Sensor and wiggle the Sensor.
Ignition on, engine not running.
Inspect the Sensor harness connector, PCM harness connector, Sensor connector, and
PCM connector for loose, bent, corroded, or pushed out pins/terminals.
Inspect the related wire harness and the splices in the CMP circuits.
Does the P0016 return?
Yes → Repair the wiring/connector concerns as needed or replace the
Camshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 7

7 Turn the ignition off. All

With the DRBIIIt lab scope probe and the Miller special tool #6801, backprobe the
(K24) CKP Signal circuit at the CKP harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Start the engine.
Observe the lab scope screen.
Are there any irregular or missing signals?

Yes → Go To 8
No → Go To 11

8 Turn the ignition off. All

Visually inspect the related wire harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wire harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Make sure the Crankshaft Position Sensor and the Camshaft Position Sensor are
properly installed and the mounting bolt(s) tight.
Refer to any TSBs that may apply.
Were any of the above conditions present?

Yes → Repair as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 9

9 Remove the Crankshaft Position Sensor. All

Inspect the Tone Wheel/Flex Plate slots for damage, foreign material, or excessive
movement.
Were any problems found?
Yes → Repair or replace the Tone Wheel/Flex Plate as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 10

37
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT — Continued

TEST ACTION APPLICABILITY

10 If there are no possible causes remaining, view repair. All

Repair
Replace the Crankshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

11 NOTE: The conditions that set this DTC are not present at this time. The All
following test may help in identifying the intermittent condition.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Start the engine.
Gently tap on the Crank Position Sensor and wiggle the CKP Sensor.
Turn the ignition off.
Inspect the Sensor harness connector, PCM harness connector, Sensor connector, and
PCM connector for loose, bent, corroded, or pushed out pins/terminals.
Inspect the related wire harness and the splices in the CKP circuits.
Were any problems found?

Yes → Repair the wiring/connector concerns as needed or replace the

Crankshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Test Complete.

38
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom List:
P0031-O2 SENSOR 1/1 HEATER CIRCUIT LOW
P0037-O2 SENSOR 1/2 HEATER CIRCUIT LOW
P0051-O2 SENSOR 2/1 HEATER CIRCUIT LOW
P0057-O2 SENSOR 2/2 HEATER CIRCUIT LOW

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0031-O2 SENSOR 1/1 HEATER
CIRCUIT LOW.

When Monitored and Set Condition:

P0031-O2 SENSOR 1/1 HEATER CIRCUIT LOW

When Monitored: Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is
on.
Set Condition: O2 Heater element input is below the minimum acceptable voltage.

P0037-O2 SENSOR 1/2 HEATER CIRCUIT LOW

When Monitored: Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is
on.
Set Condition: O2 Heater element input is below the minimum acceptable voltage.

P0051-O2 SENSOR 2/1 HEATER CIRCUIT LOW

When Monitored: Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is
on.
Set Condition: O2 Heater element input is below the minimum acceptable voltage.

P0057-O2 SENSOR 2/2 HEATER CIRCUIT LOW

When Monitored: Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is
on.
Set Condition: O2 Heater element input is below the minimum acceptable voltage.

POSSIBLE CAUSES
O2 SENSOR HEATER OPERATION
O2 HEATER ELEMENT
O2 HEATER CONTROL CIRCUIT
O2 HEATER CONTROL SHORTED TO GROUND
PCM

39
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0031-O2 SENSOR 1/1 HEATER CIRCUIT LOW — Continued

TEST ACTION APPLICABILITY

1 Turn the ignition off. All
NOTE: Wait a minimum of 8 minutes to allow the O2 Sensor to cool down
before continuing the test. Allow the O2 Sensor voltage to stabilize at 5.0
volts.
Ignition on, engine not running.
With the DRBIIIt, actuate the O2 Heater Test.
With the DRBIIIt, monitor O2 Sensor voltage for at least 2 minutes.
Does the O2 Sensor voltage stay above 4.5 volts?

Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

NOTE: Allow the O2 Sensor to cool to room temperature.
Disconnect the O2 Sensor harness connector.
Measure the resistance across the O2 Sensor Heater element component side.
Is the resistance between 2.0 and 30 ohms?
Yes → Go To 3

No → Replace the O2 Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

3 Ignition on, engine not running. All

With the DRBIIIt, actuate the O2 Heater Test with the O2 Sensor harness connector
still disconnected.
Using a 12-volt test light connected to ground, probe the O2 Heater Control circuit at
the O2 Sensor harness connector.
Does the test light illuminate brightly and flash on and off?
Yes → Replace the O2 Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Turn the ignition off. All

Disconnect the PCM harness connectors.
Measure the resistance between ground and the O2 Heater Control circuit at the O2
Sensor harness connector.
Is the resistance below 5.0 ohms?

Yes → Repair the short to ground in the O2 Sensor Heater Control

circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

40
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom List:
P0032-O2 SENSOR 1/1 HEATER CIRCUIT HIGH
P0038-O2 SENSOR 1/2 HEATER CIRCUIT HIGH
P0052-O2 SENSOR 2/1 HEATER CIRCUIT HIGH
P0058-O2 SENSOR 2/2 HEATER CIRCUIT HIGH

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0032-O2 SENSOR 1/1 HEATER
CIRCUIT HIGH.

When Monitored and Set Condition:

P0032-O2 SENSOR 1/1 HEATER CIRCUIT HIGH

When Monitored: Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is
off.
Set Condition: O2 Heater element input is above the maximum acceptable voltage.

P0038-O2 SENSOR 1/2 HEATER CIRCUIT HIGH

When Monitored: Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is
off.
Set Condition: O2 Heater element input is above the maximum acceptable voltage.

P0052-O2 SENSOR 2/1 HEATER CIRCUIT HIGH

When Monitored: Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is
off.
Set Condition: O2 Heater element input is above the maximum acceptable voltage.

P0058-O2 SENSOR 2/2 HEATER CIRCUIT HIGH

When Monitored: Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is
off.
Set Condition: O2 Heater element input is above the maximum acceptable voltage.

POSSIBLE CAUSES
O2 SENSOR HEATER OPERATION
O2 HEATER ELEMENT
O2 HEATER GROUND CIRCUIT OPEN
O2 SENSOR
O2 HEATER CONTROL SHORTED TO VOLTAGE
O2 HEATER CONTROL CIRCUIT OPEN
PCM

41
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0032-O2 SENSOR 1/1 HEATER CIRCUIT HIGH — Continued

TEST ACTION APPLICABILITY

1 Turn the ignition off. All
NOTE: Wait a minimum of 8 minutes to allow the O2 Sensor to cool down
before continuing the test. Allow the O2 Sensor voltage to stabilize at 5.0
volts.
Ignition on, engine not running.
With the DRBIIIt, actuate the O2 Heater Test.
With the DRBIIIt, monitor O2 Sensor voltage for at least 2 minutes.
Does the O2 Sensor voltage stay above 4.5 volts?

Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

NOTE: Allow the O2 Sensor to cool down to room temperature.
Disconnect the O2 Sensor harness connector.
Measure the resistance across the O2 Sensor Heater element component side.
Is the resistance between 2.0 and 30 ohms?
Yes → Go To 3

No → Replace the O2 Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

3 Ignition on, engine not running. All

With the DRBIIIt, actuate the O2 Heater Test with the Sensor harness connector
still disconnected.
Using a 12-volt test light connected to ground, probe the O2 Heater Control circuit at
the O2 Sensor harness connector.
Does the test light illuminate brightly and flash on and off?
Yes → Go To 4
No → Go To 5

4 Turn the ignition off. All

Measure the resistance between engine ground and the O2 Heater ground circuit at
the O2 Sensor harness connector.
Is the resistance below 5.0 ohms?

Yes → Replace the O2 Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Repair the open in the O2 Heater ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Turn the ignition off. All

Disconnect the PCM harness connectors.
Ignition on, engine not running.
Measure the voltage on the O2 Heater Control circuit at the O2 Sensor harness
connector.
Does the voltmeter indicate any voltage present?
Yes → Repair the short to voltage in the O2 Heater Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 6

42
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0032-O2 SENSOR 1/1 HEATER CIRCUIT HIGH — Continued

TEST ACTION APPLICABILITY

6 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the O2 Heater Control circuit from the O2 Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 7
No → Repair the open in the O2 Heater Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

43
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom List:
P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELA-
TION - VACUUM LEAK DETECTED
P2074-MAP SENSOR/TP SENSOR CORRELATION - VACUUM LEAK
DETECTED

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0068-MANIFOLD PRESSURE/
THROTTLE POSITION CORRELATION - VACUUM LEAK DE-
TECTED.

When Monitored and Set Condition:

P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION - VAC-

UUM LEAK DETECTED
When Monitored: During all drive modes.
Set Condition: If vacuum drops below 1.59Hg with engine RPM greater than 2000 RPM
and closed throttle.

P2074-MAP SENSOR/TP SENSOR CORRELATION - VACUUM LEAK DETECTED

When Monitored: During all drive modes.
Set Condition: If vacuum drops below 1.59Hg with engine RPM greater than 2000 RPM
and closed throttle. One Trip Fault. Three good trips to turn off the MIL.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
VACUUM LEAK
RESISTANCE IN (F856) 5-VOLT SUPPLY CIRCUIT
(F856) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
MAP SENSOR
RESISTANCE IN THE (K1) MAP SIGNAL CIRCUIT
(K1) MAP SIGNAL CIRCUIT SHORTED TO GROUND
RESISTANCE IN THE (K900) SENSOR GROUND CIRCUIT
TP SENSOR OPERATION
RESISTANCE IN THE (F855) 5-VOLT SUPPLY CIRCUIT
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
TP SENSOR
RESISTANCE IN THE (K22) TP SENSOR NO.1 SIGNAL CIRCUIT
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT SHORTED TO GROUND

44
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION -

VACUUM LEAK DETECTED — Continued
POSSIBLE CAUSES
RESISTANCE IN THE (K900) SENSOR GROUND CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 NOTE: Diagnose any TP Sensor or MAP Sensor component DTCs before All
continuing.
NOTE: If the P0501 - No Vehicle Speed Signal is set with this DTC, refer to
the P0501 diagnostics before continuing.
NOTE: The throttle plate and linkage should be free from binding and
carbon build up.
NOTE: Make sure the throttle plate is at the idle position.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 NOTE: This code is enabled on engines with a plastic intake manifold and is All
intended to shut down the engine if a large crack occurs.
NOTE: A large vacuum leak is most likely the cause of this DTC.
Inspect the Intake Manifold for leaks and cracks.
Inspect the Power Brake Booster for vacuum leaks.
Inspect the PCV system for proper operation or vacuum leaks.
Inspect the MAP Sensor for proper installation.
Were any vacuum leaks found?
Yes → Repair the vacuum leak as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

3 Start the engine. All

With the DRBIIIt, monitor the MAP Sensor voltage.
Snap the throttle.
Does the MAP Sensor voltage vary from below 2.0 volts at idle to above 3.5 volts at
WOT.

Yes → Go To 4

No → Go To 11

4 Ignition on, engine not running. All

With the DRBIIIt, monitor the TP Sensor voltage while slowly depressing the
throttle pedal from closed to wide open throttle.
Does voltage start approximately at 0.8 of a volt and go above 3.5 volts with a smooth
transition?
Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

45
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION -

VACUUM LEAK DETECTED — Continued
TEST ACTION APPLICABILITY
5 Turn the ignition off. All
Disconnect the TP Sensor harness connector.
Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (F855) 5-volt Supply circuit from the TP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 6

No → Repair the excessive resistance in the (F855) 5-volt Supply circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Measure the resistance between ground and (F855) 5-volt Supply circuit at the TP All
Sensor harness connector.
Is the resistance above 100k ohms?
Yes → Go To 7
No → Repair the short to ground in the (F855) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Connect the C2 PCM harness connector. All

Ignition on, engine not running.
With the DRBIIIt, monitor the TP Sensor voltage.
Connect a jumper wire between the (K22) TP Sensor No.1 Signal circuit and the
(K900) Sensor ground circuit at the Sensor harness connector.
Does the TP Sensor voltage change from approximately 4.9 volts to below 0.5 of a
volt?
Yes → Replace the Throttle Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 8

NOTE: Remove the jumper wire before continuing.

8 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K22) TP Sensor No.1 Signal circuit from the TP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 9

No → Repair the excessive resistance in the (K22) TP Sensor No.1

Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

46
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION -

VACUUM LEAK DETECTED — Continued
TEST ACTION APPLICABILITY
9 Measure the resistance between ground and the (K22) TP Sensor No.1 Signal circuit All
at the TP Sensor harness connector.
Is the resistance above 100k ohms?

Yes → Go To 10
No → Repair the short to ground in the (K22) TP Sensor No.1 Signal
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

10 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the TP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 17
No → Repair the excessive resistance in the (K900) Sensor Ground
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

11 Turn the ignition off. All

Disconnect the MAP Sensor harness connector.
Disconnect the C1 and C2 PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (F856) 5-volt Supply circuit from the MAP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 12
No → Repair the excessive resistance in the (F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

12 Measure the resistance between ground and the (F856) 5-volt Supply circuit at the All
MAP Sensor harness connector.
Is the resistance above 100k ohms?

Yes → Go To 13
No → Repair the short to ground in the (F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

47
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION -

VACUUM LEAK DETECTED — Continued
TEST ACTION APPLICABILITY
13 Turn the ignition off. All
Connect the C1 and C2 PCM harness connectors.
Ignition on, engine not running.
With the DRBIIIt, monitor the MAP Sensor voltage.
Connect a jumper wire between the (K1) MAP Signal circuit and the (K900) Sensor
ground circuit.
Cycle the ignition switch from off to on.
Does the DRBIIIt display MAP voltage from approximately 4.9 volts to below 0.5 of
a volt?

Yes → Replace the MAP Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 14
NOTE: Remove the jumper wire before continuing.

14 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K1) MAP Signal circuit from the MAP Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 15
No → Repair the excessive resistance in the (K1) MAP Signal circuit
Perform POWERTRAIN VERIFICATION TEST VER - 5.

15 Measure the resistance between ground and the (K1) MAP Signal circuit at the MAP All
Sensor harness connector.
Is the resistance above 100k ohms?
Yes → Go To 16

No → Repair the short to ground in the (K1) MAP Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

16 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the MAP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 17

No → Repair the excessive resistance in the (K900) Sensor ground

circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

48
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION -

VACUUM LEAK DETECTED — Continued
TEST ACTION APPLICABILITY
17 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

49
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0071-AMBIENT TEMP SENSOR PERFORMANCE

When Monitored and Set Condition:

P0071-AMBIENT TEMP SENSOR PERFORMANCE

When Monitored: Engine off time is greater than 480 minutes and Ambient Temperature
is greater than 4 deg C (39 deg F).
Set Condition: After a calibrated amount of cool down time, the PCM compares the ECT
Sensor, IAT Sensor and the Ambient Air Temperature Sensor values. The Ambient Air
Temperature Sensor value is not within -10 deg C (18 deg F) of the other two temperature
sensor’s. Two Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
(G31) AAT SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
AAT SENSOR
(G31) AAT SIGNAL CIRCUIT OPEN
(K900) SENSOR GROUND CIRCUIT OPEN
(G31) AAT SIGNAL CIRCUIT SHORTED TO GROUND
(G31) AAT SIGNAL CIRCUIT SHORTED TO (K900) SENSOR GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 NOTE: Visually inspect both the component and the PCM connectors. Look All
for damage, partially broken wires and backed out or corroded terminals
Turn the ignition off.
Disconnect the C1 and C2 PCM harness connectors.
Disconnect the Ambient Temp Sensor harness connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground probe the (G31) AAT Signal circuit at
the Ambient Temp Sensor harness connector.
Does the test light illuminate brightly?

Yes → Repair the short to voltage in the (G31) AAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 3

50
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0071-AMBIENT TEMP SENSOR PERFORMANCE — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Connect the C1 and C2 PCM harness connectors.
Ignition on, engine not running.
With the DRBIIIt, read the Ambient Temperature Sensor voltage.
Is the voltage above 4.6 volts?

Yes → Go To 4

No → Go To 7

4 Connect a jumper wire across the (G31) AAT Signal circuit and the (K900) Sensor All
ground circuit terminals of the Sensor harness connector.
With the DRBIIIt, read the AAT Sensor voltage.
Is the voltage below 1.0 volt?

Yes → Replace the Ambient Temperature Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5
NOTE: Remove the jumper wire before continuing.

5 Turn the ignition off. All

Disconnect the C1 and C2 PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (G31) AAT Signal circuit from the AAT Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 6
No → Repair the open in the (G31) AAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the AAT Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 9

No → Repair the open in the (K900) Sensor ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Turn the ignition off. All

Disconnect the C1 and C2 PCM harness connectors.
Measure the resistance between ground and the (G31) AAT Signal circuit at the AAT
Sensor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (G31) AAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 8

51
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0071-AMBIENT TEMP SENSOR PERFORMANCE — Continued

TEST ACTION APPLICABILITY

8 Measure the resistance between the (G31) AAT Signal circuit and the (K900) Sensor All
ground circuit at the AAT Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short between the (K900) Sensor ground circuit and
the (G31) AAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 9

9 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

52
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0072-AMBIENT TEMP SENSOR CIRCUIT LOW

When Monitored and Set Condition:

P0072-AMBIENT TEMP SENSOR CIRCUIT LOW

When Monitored: The ignition key on.
Set Condition: Ambient Temperature Sensor is less than 0.039 of a volt at the PCM for
4.8 seconds. Three good trips to clear the MIL.

POSSIBLE CAUSES
AAT SENSOR VOLTAGE BELOW 0.3 OF A VOLT
AAT SENSOR
(G31) AAT SIGNAL CIRCUIT SHORTED TO GROUND
(G31) ATT SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the Ambient Temperature Sensor voltage.
Is the voltage below 0.3 of a volt?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the Ambient Temperature Sensor harness connector.
Ignition on, engine not running.
With the DRBIIIt, read AAT Sensor voltage.
Is the voltage above 4.6 volts?

Yes → Replace the Ambient Temperature Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

3 Turn the ignition off. All

Disconnect the C1 and C2 PCM harness connectors.
Measure the resistance between ground and the (G31) AAT Signal circuit at the AAT
Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (G31) AAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

53
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0072-AMBIENT TEMP SENSOR CIRCUIT LOW — Continued

TEST ACTION APPLICABILITY

4 Measure the resistance between the (G31) AAT Signal circuit and the (K900) Sensor All
ground circuit at the AAT Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short between the (K900) Sensor ground circuit and
the (G31) AAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

54
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0073-AMBIENT TEMP SENSOR CIRCUIT HIGH

When Monitored and Set Condition:

P0073-AMBIENT TEMP SENSOR CIRCUIT HIGH

When Monitored: The ignition key on.
Set Condition: The Ambient Temperature Sensor voltage is greater than 4.94 volts at the
PCM for 4.8 seconds. Three good trips to clear the MIL.

POSSIBLE CAUSES
AAT SENSOR VOLTAGE ABOVE 4.8 VOLTS
AAT SENSOR
(G31) AAT SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(G31) AAT SIGNAL CIRCUIT OPEN
(K900) SENSOR GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the Ambient Temperature Sensor voltage.
Is the voltage above 4.8 volts?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the Ambient Temperature Sensor harness connector.
Connect a jumper wire between the (G31) AAT Signal circuit and the (K900) Sensor
ground circuit at the AAT Sensor harness connector.
Ignition on, engine not running.
With the DRBIIIt, read Ambient Temperature Sensor voltage.
Is the voltage below 1.0 volt?
Yes → Replace the Ambient Temperature Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

NOTE: Remove the jumper wire before continuing.

55
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0073-AMBIENT TEMP SENSOR CIRCUIT HIGH — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C1 and C2 PCM harness connectors.
Ignition on, engine not running.
Using a 12-volt test light connected to ground probe the (G31) AAT Signal circuit at
the AAT Sensor harness connector.
Does the test light illuminate brightly?

Yes → Repair the short to voltage in the (G31) AAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (G31) AAT Signal circuit from the AAT Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (G31) AAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the AAT Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6
No → Repair the open in the (K900) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

56
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0107-MAP SENSOR CIRCUIT LOW

When Monitored and Set Condition:

P0107-MAP SENSOR CIRCUIT LOW

When Monitored: Engine speed greater than 250 RPM. Battery voltage greater than 10.3
volts.
Set Condition: The MAP sensor signal voltage is below 0.08 of a volt for 1.7 seconds. One
Trip Fault.

POSSIBLE CAUSES
MAP SENSOR VOLTAGE BELOW 0.08 OF A VOLT
(F856) 5-VOLT SUPPLY CIRCUIT OPEN
(F856) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
MAP SENSOR
(K1) MAP SIGNAL CIRCUIT SHORTED TO GROUND
(K1) MAP SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
With the DRBIIIt, read the MAP Sensor voltage.
Is the voltage below 0.08 of a volt?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the MAP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the (F856) 5-volt Supply circuit at the MAP Sensor harness
connector.
Is the voltage between 4.5 to 5.2 volts?
Yes → Go To 3

No → Go To 6

3 With the DRBIIIt, monitor the MAP Sensor voltage with the Sensor harness All
connector disconnected.
Is the voltage above 1.2 volts?
Yes → Replace the MAP Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

57
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0107-MAP SENSOR CIRCUIT LOW — Continued

TEST ACTION APPLICABILITY

4 Turn the ignition off. All
Disconnect the C1 and C2 PCM harness connectors.
Measure the resistance between ground and the (K1) MAP Signal circuit at the MAP
Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (K1) MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 Measure the resistance between the (K1) MAP Signal circuit and the (K900) Sensor All
ground circuit at the MAP Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short between the (K900) Sensor ground and the (K1)
MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 8

6 Turn the ignition off. All

Disconnect the C1 and C2 PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (F856) 5-volt Supply circuit from the MAP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 7

No → Repair the open in the (F856) 5-volt Supply circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Measure the resistance between ground and the (F856) 5-volt Supply circuit at the All
MAP Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 8

8 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

58
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0108-MAP SENSOR CIRCUIT HIGH

When Monitored and Set Condition:

P0108-MAP SENSOR CIRCUIT HIGH

When Monitored: Engine RPM greater than 260. Battery voltage greater than 10.3 volts
Set Condition: The MAP sensor signal voltage is greater than 4.93 volts.

POSSIBLE CAUSES
MAP SENSOR VOLTAGE ABOVE 4.93 VOLTS
MAP SENSOR
(K1) MAP SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K1) MAP SIGNAL CIRCUIT OPEN
(K1) MAP SIGNAL CIRCUIT SHORTED TO THE (F856) 5-VOLT SUPPLY CIRCUIT
(K900) SENSOR GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Start the engine. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
With the DRBIIIt, read the MAP Sensor voltage.
Is the voltage above 4.93 volts?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the MAP Sensor harness connector.
Connect a jumper wire between the (K1) MAP Signal circuit and the (K900) Sensor
ground circuit in the harness connector.
Ignition on, engine not running.
With the DRBIIIt, monitor the MAP Sensor voltage.
Is the voltage below 1.0 volt?

Yes → Replace the MAP Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 3

NOTE: Remove the jumper wire before continuing.

59
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0108-MAP SENSOR CIRCUIT HIGH — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C1 and C2 PCM harness connectors.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (K1) MAP Signal circuit at
the MAP Sensor harness connector.
Does the test light illuminate brightly?

Yes → Repair the short to voltage in the (K1) MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K1) MAP Signal circuit from the MAP Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (K1) MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Measure the resistance between the (K1) MAP Signal circuit and the (F856) 5-volt All
Supply circuit at the MAP Sensor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short between the (F856) 5-volt Supply circuit and the
(K1) MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 6

6 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the MAP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 7
No → Repair the open in the (K900) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

60
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0111-INTAKE AIR TEMPERATURE SENSOR PERFORMANCE

When Monitored and Set Condition:

P0111-INTAKE AIR TEMPERATURE SENSOR PERFORMANCE

When Monitored: The engine off time is greater than 480 minutes. Ambient Temperature
is greater than 4 deg C (38 deg F).
Set Condition: After a calibrated amount of cool down time the PCM compares the ECT
Sensor, IAT Sensor, and the Ambient Air Temp Sensor values. The IAT Sensor value is not
within -10 deg C (18 deg F) of the other two temperature sensors. Two Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
(K21) IAT SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
IAT SENSOR
(K21) IAT SIGNAL CIRCUIT OPEN
(K900) SENSOR GROUND CIRCUIT OPEN
(K21) IAT SIGNAL CIRCUIT SHORTED TO GROUND
(K21) IAT SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the IAT Sensor harness connector.
Disconnect the C2 PCM harness connector.
NOTE: Visually inspect both the component and the PCM connectors. Look
for damaged, partially broken wires, and backed out or corroded terminals.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (K21) IAT Signal circuit in
the IAT Sensor harness connector.
Does the test light illuminate brightly?

Yes → Repair the short to voltage in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 3

61
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0111-INTAKE AIR TEMPERATURE SENSOR PERFORMANCE —

Continued
TEST ACTION APPLICABILITY
3 Turn the ignition off. All
Connect the C2 PCM harness connector.
Ignition on, engine not running.
With the DRBIIIt, read the IAT voltage.
Is the voltage above 4.6 volts?

Yes → Go To 4

No → Go To 7

4 Connect a jumper wire between the (K21) IAT Signal circuit and (K900) Sensor All
ground circuit in the IAT Sensor harness connector.
With the DRBIIIt, read the IAT Sensor voltage.
Is the voltage below 1.0 volt?

Yes → Replace the IAT Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5
NOTE: Remove the jumper wire before continuing.

5 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K21) IAT Signal circuit from the IAT Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 6
No → Repair the open in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the IAT Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 9

No → Repair the open in the (K900) Sensor ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Measure the resistance between ground and the (K21) IAT Signal circuit at the IAT
Sensor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 8

62
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0111-INTAKE AIR TEMPERATURE SENSOR PERFORMANCE —

Continued
TEST ACTION APPLICABILITY
8 Measure the resistance between the (K900) Sensor ground circuit and the (K21) IAT All
Signal circuit at the IAT Sensor harness connector.
Is the resistance below 5.0 ohms?

Yes → Repair the short between the (K900) Sensor ground circuit and
the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 9

9 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

63
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0112-INTAKE AIR TEMPERATURE SENSOR CIRCUIT LOW

When Monitored and Set Condition:

P0112-INTAKE AIR TEMPERATURE SENSOR CIRCUIT LOW

When Monitored: With the ignition on. Battery voltage greater than 10 volts.
Set Condition: The Intake Air Temperature (IAT) sensor circuit voltage at the PCM goes
below 0.5 of a volt. One Trip Failure.

POSSIBLE CAUSES
IAT SENSOR VOLTAGE BELOW 0.5 OF A VOLT
IAT SENSOR
(K21) IAT SIGNAL CIRCUIT SHORTED TO GROUND
(K21) IAT SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the IAT Sensor voltage.
Is the voltage below 0.5 of a volt?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the IAT harness connector.
Ignition on, engine not running.
With the DRBIIIt, read the IAT Sensor voltage.
Is the voltage above 1.0 volt?

Yes → Replace the IAT Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

3 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Measure the resistance between ground and the (K21) IAT Signal circuit at the IAT
Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

64
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0112-INTAKE AIR TEMPERATURE SENSOR CIRCUIT LOW — Continued

TEST ACTION APPLICABILITY

4 Measure the resistance between the (K21) IAT Signal circuit and the (K900) Sensor All
ground circuit at the IAT Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short between the (K900) Sensor ground and the (K21)
IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

65
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0113-INTAKE AIR TEMPERATURE SENSOR CIRCUIT HIGH

When Monitored and Set Condition:

P0113-INTAKE AIR TEMPERATURE SENSOR CIRCUIT HIGH

When Monitored: With the ignition on. Battery voltage greater than 10 volts.
Set Condition: The Intake Air Temperature (IAT) sensor circuit voltage at the PCM goes
above 4.9 volts. One Trip Failure.

POSSIBLE CAUSES
IAT SENSOR VOLTAGE ABOVE 4.9 VOLTS
IAT SENSOR
(K21) IAT SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K21) IAT SIGNAL CIRCUIT OPEN
(K900) SENSOR GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the IAT Sensor voltage.
Is the voltage above 4.9 volts?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the IAT harness connector.
Connect a jumper wire between the (K21) IAT Signal circuit and the (K900) Sensor
ground circuit at the IAT harness connector.
Ignition on, engine not running.
With the DRBIIIt, read the IAT Sensor voltage.
Is the voltage below 1.0 volt?
Yes → Replace the IAT Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

NOTE: Remove the jumper wire before continuing.

66
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0113-INTAKE AIR TEMPERATURE SENSOR CIRCUIT HIGH — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C2 PCM harness connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (K21) IAT Signal circuit at
the IAT Sensor harness connector.
Does the test light illuminate brightly?

Yes → Repair the short to voltage in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K21) IAT Signal circuit from the IAT Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the IAT Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6
No → Repair the open in the (K900) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

67
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0116-ENGINE COOLANT TEMPERATURE CIRCUIT PERFOR-
MANCE

When Monitored and Set Condition:

P0116-ENGINE COOLANT TEMPERATURE CIRCUIT PERFORMANCE

When Monitored: Engine off time is greater than 480 minutes. Ambient temperature is
greater than 4 deg C (38 deg F).
Set Condition: After a calibrated amount of cool down time the PCM compares the ECT
Sensor, IAT Sensor, and the Ambient Air Temp Sensor values. If the IAT Sensor value is not
within 10 deg C (18 deg F) of the other two temperature sensors. Two Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
(K2) ECT SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
ECT SENSOR
(K2) ECT SIGNAL CIRCUIT OPEN
(K900) SENSOR GROUND CIRCUIT OPEN
(K2) ECT SIGNAL CIRCUIT SHORTED TO GROUND
(K2) ECT SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Disconnect the ECT Sensor harness connector.
NOTE: Visually inspect both the component and the PCM connectors. Look
for damaged, partially broken wires, and backed out or corroded terminals.
Ignition on, engine not running.
Measure the voltage on the (K2) ECT Signal circuit at the ECT Sensor harness
connector.
Is the voltage above 5.2 volts?

Yes → Repair the short to voltage in the (K2) ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 3

68
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0116-ENGINE COOLANT TEMPERATURE CIRCUIT PERFORMANCE —

Continued
TEST ACTION APPLICABILITY
3 Turn the ignition off. All
Connect the C2 PCM harness connector.
Ignition on, engine not running.
With the DRBIIIt, read the ECT Sensor voltage.
Is the voltage above 4.6 volts?

Yes → Go To 4

No → Go To 7

4 Connect a jumper wire between the (K2) ECT Signal circuit and the (K900) Sensor All
ground circuit at the ECT Sensor harness connector.
With the DRBIIIt, read the ECT voltage.
Is the voltage below 1.0 volt?

Yes → Replace the ECT Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K2) ECT Signal circuit from the ECT Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6

No → Repair the open in the (K2) ECT Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the ECT Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 9

No → Repair the open in the (K900) Sensor ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Measure the resistance between ground and the (K2) ECT Signal circuit at the ECT
Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (K2) ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 8

69
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0116-ENGINE COOLANT TEMPERATURE CIRCUIT PERFORMANCE —

Continued
TEST ACTION APPLICABILITY
8 Measure the resistance between the (K2) ECT Signal circuit and the (K900) Sensor All
ground circuit at the ECT Sensor harness connector.
Is the resistance below 5.0 ohms?

Yes → Repair the short between the (K900) Sensor ground and the (K2)
ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 9

9 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

70
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0117-ENGINE COOLANT TEMPERATURE SENSOR CIRCUIT LOW

When Monitored and Set Condition:

P0117-ENGINE COOLANT TEMPERATURE SENSOR CIRCUIT LOW

When Monitored: With the ignition on. Battery voltage greater than 10 volts.
Set Condition: The Engine Coolant Temperature (ECT) sensor circuit voltage at the PCM
is less than 0.5 of a volt for more than 2.6 seconds. One Trip Fault

POSSIBLE CAUSES
ECT SENSOR VOLTAGE BELOW 0.5 OF A VOLT
ECT SENSOR
(K2) ECT SIGNAL CIRCUIT SHORTED TO GROUND
(K2) ECT SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the ECT Sensor voltage.
Is the voltage below 0.5 of a volt?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the ECT harness connector.
Ignition on, engine not running.
With the DRBIIIt, read ECT Sensor voltage.
Is the voltage above 1.0 volt?

Yes → Replace the ECT Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

3 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Measure the resistance between ground and the (K2) ECT Signal circuit at the ECT
Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (K2) ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

71
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0117-ENGINE COOLANT TEMPERATURE SENSOR CIRCUIT LOW —

Continued
TEST ACTION APPLICABILITY
4 Measure the resistance between the (K2) ECT Signal circuit and the (K900) Sensor All
ground circuit at the ECT Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short between the (K900) Sensor ground and the (K2)
ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

72
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0118-ENGINE COOLANT TEMPERATURE SENSOR CIRCUIT
HIGH

When Monitored and Set Condition:

P0118-ENGINE COOLANT TEMPERATURE SENSOR CIRCUIT HIGH

When Monitored: With the ignition on. Battery voltage greater than 10 volts.
Set Condition: The Engine Coolant Temperature (ECT) sensor circuit voltage at the PCM
is greater than 4.96 volts for more than 2.6 seconds. One Trip Fault.

POSSIBLE CAUSES
ECT SENSOR VOLTAGE ABOVE 4.96 VOLTS
ECT SENSOR
(K2) ECT SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K2) ECT SIGNAL CIRCUIT OPEN
(K900) SENSOR GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the ECT Sensor voltage.
Is the voltage above 4.96 volts?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the ECT Sensor harness connector.
Connect a jumper wire between the (K2) ECT Signal circuit and the (K900) Sensor
ground circuit at the ECT harness connector.
Ignition on, engine not running.
With the DRBIIIt, read the ECT Sensor voltage.
Is the voltage below 1.0 volt?
Yes → Replace the ECT Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

NOTE: Remove the jumper wire before continuing.

73
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0118-ENGINE COOLANT TEMPERATURE SENSOR CIRCUIT HIGH —

Continued
TEST ACTION APPLICABILITY
3 Turn the ignition off. All
Disconnect the C2 PCM harness connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (K2) ECT Signal circuit at
the ECT Sensor harness connector.
Does the test light illuminate brightly?

Yes → Repair the short to voltage in the (K2) ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K2) ECT Signal circuit from the ECT Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (K2) ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the ECT Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6
No → Repair the open in the (K900) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

74
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0122-THROTTLE POSITION SENSOR NO.1 LOW

When Monitored and Set Condition:

P0122-THROTTLE POSITION SENSOR NO.1 LOW

When Monitored: With the ignition on. Battery voltage greater than 10 volts.
Set Condition: Throttle Position Sensor voltage at the PCM is less than 0.16 of a volt for
0.7 of a second. One Trip Fault.

POSSIBLE CAUSES
THROTTLE POSITION SENSOR SWEEP
INTERMITTENT CONDITION
(F855) 5-VOLT SUPPLY CIRCUIT OPEN
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
THROTTLE POSITION SENSOR
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT SHORTED TO GROUND
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
NOTE: Diagnose any IAC codes before continuing.
With the DRBIIIt, read the TP Sensor voltage.
Is the voltage below 0.2 of a volt?
Yes → Go To 2

No → Go To 9

2 Turn the ignition off. All

Disconnect the TP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the (F855) 5-volt Supply circuit at the TP Sensor harness
connector.
Is the voltage between 4.5 to 5.2 volts?

Yes → Go To 3

No → Go To 6

3 With the DRBIIIt, monitor the TP Sensor voltage with the Sensor harness connector All
disconnected.
Is the voltage above 4.5 volts?

Yes → Replace the Throttle Position Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

75
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0122-THROTTLE POSITION SENSOR NO.1 LOW — Continued

TEST ACTION APPLICABILITY

4 Turn the ignition off. All
Disconnect the C2 PCM harness connector.
Measure the resistance between ground and the (K22) TP Sensor No.1 Signal circuit
at the TP Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (K22) TP Sensor No.1 Signal
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 Measure the resistance between the (K22) TP Sensor No.1 Signal circuit and the All
(K900) Sensor ground circuit at the TP Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short between the (K900) Sensor ground and the (K22)
TP Sensor No.1 Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 8

6 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (F855) 5-volt Supply circuit from the TP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 7

No → Repair the open in the (F855) 5-volt Supply circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Measure the resistance between ground and the (F855) 5-volt Supply circuit at the All
TP Sensor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (F855) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 8

8 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

76
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0122-THROTTLE POSITION SENSOR NO.1 LOW — Continued

TEST ACTION APPLICABILITY

9 Ignition on, engine not running. All
With the DRBIIIt, monitor the Throttle Position Sensor voltage.
Slowly open the throttle from the idle position to the wide open throttle position.
Does voltage start at approximately 0.8 of a volt and go above 3.5 volts with a smooth
transition?

Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Replace the Throttle Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

77
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0123-THROTTLE POSITION SENSOR NO.1 HIGH

When Monitored and Set Condition:

P0123-THROTTLE POSITION SENSOR NO.1 HIGH

When Monitored: With the ignition on. Battery voltage greater than 10 volts.
Set Condition: Throttle Position Sensor voltage at the PCM is greater than 4.5 volts for
0.7 of a second. One Trip Fault.

POSSIBLE CAUSES
THROTTLE POSITION SENSOR SWEEP
INTERMITTENT CONDITION
THROTTLE POSITION SENSOR
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT OPEN
(K22) TP SENSOR NO.1 SIGNAL CIRCUIT SHORTED TO THE (F855) 5-VOLT SUPPLY CIRCUIT
(K900) SENSOR GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 NOTE: Ensure the throttle is fully closed and free from binding or carbon All
build up.
Start the engine.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
NOTE: Diagnose any IAC codes before continuing.
With the DRBIIIt, read the TP Sensor voltage.
Is the voltage above 4.5 volts?

Yes → Go To 2

No → Go To 8

2 Turn the ignition off. All

Disconnect the TP Sensor harness connector.
Connect a jumper wire between the (K22) TP Sensor No.1 Signal circuit and the
(K900) Sensor ground circuit at the Sensor harness connector.
With the DRBIIIt, monitor the TP Sensor voltage.
Ignition on, engine not running.
Is the voltage below 0.5 of a volt?

Yes → Replace the Throttle Position Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 3

NOTE: Remove the jumper wire before continuing.

78
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0123-THROTTLE POSITION SENSOR NO.1 HIGH — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C2 PCM harness connector.
Ignition on, engine not running.
Measure the voltage on the (K22) TP Sensor No.1 Signal circuit at the TP Sensor
harness connector.
Is the voltage above 5.2 volts?

Yes → Repair the short to voltage in the (K22) TP Sensor No.1 Signal
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K22) TP Sensor No.1 Signal circuit from the TP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 5
No → Repair the open in the (K22) TP Sensor No.1 Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Measure the resistance between the (K22) TP Sensor No.1 Signal circuit and the All
(F855) 5-volt Supply circuit at the TP Sensor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short between the (F855) 5-volt Supply circuit and the
(K22) TP Sensor No.1 Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

6 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the TP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 7

No → Repair the open in the (K900) Sensor ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

79
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0123-THROTTLE POSITION SENSOR NO.1 HIGH — Continued

TEST ACTION APPLICABILITY

8 Ignition on, engine not running. All
With the DRBIIIt, monitor the Throttle Position Sensor voltage.
Slowly open the throttle from the idle position to the wide open throttle position.
Does voltage start at approximately 0.8 of a volt and go above 3.5 volts with a smooth
transition?

Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Replace the Throttle Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

80
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0125-INSUFFICIENT COOLANT TEMP FOR CLOSED-LOOP FUEL
CONTROL

When Monitored and Set Condition:

P0125-INSUFFICIENT COOLANT TEMP FOR CLOSED-LOOP FUEL CONTROL

When Monitored: With battery voltage greater than 10.4 volts and after engine is started.
Set Condition: The engine temperature does not go above -10°C (15°F). Failure time
depends on start-up coolant temperature and ambient temperature. (i.e. 2 minutes for a
start temp of -10°C (15°F) or up to 10 mintues for a vehicle with a start-up temp of -28°C
(5°F). Two Trip Fault.

POSSIBLE CAUSES
LOW COOLANT LEVEL
THERMOSTAT OPERATION
ECT SENSOR

TEST ACTION APPLICABILITY

1 NOTE: If a Engine Coolant Temperature (ECT) DTC is set along with this All
code, diagnose the ECT DTC first.
NOTE: Inspect the ECT terminals and related PCM terminals. Ensure the
terminals are free from corrosion and damage.
NOTE: The best way to diagnose this DTC is to allow the vehicle to sit
overnight outside in order to have a totally cold soaked engine.
NOTE: Extremely cold outside ambient temperatures may have caused this
DTC to set.
WARNING: Never open the cooling system when the engine is hot. The
system is under pressure. Extreme burns or scalding may result. Allow the
engine to cool before opening the cooling system.
Inspect the coolant system for proper level and condition.
Is the coolant level and condition OK?

Yes → Go To 2

No → Inspect the vehicle for a coolant leak and add the necessary
amount of coolant.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

81
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0125-INSUFFICIENT COOLANT TEMP FOR CLOSED-LOOP FUEL CON-

TROL — Continued
TEST ACTION APPLICABILITY
2 NOTE: This test works best if performed on a cold engine (cold soak) All
Ignition on, engine not running.
With the DRBIIIt, read the Eng Coolant Tmp Deg value. If the engine was allowed
to sit overnight (cold soak), the temperature value should be a sensible value that is
somewhere close to the ambient temperature.
NOTE: If engine coolant temperature is above 82°C (180°F), allow the engine
to cool until 65°C (150°F) is reached.
Start the Engine.
During engine warm-up monitor the Eng Coolant Tmp Deg value. The temp deg
value change should be a smooth transition from start up to normal operating temp
82°C (180°F) . Also monitor the actual coolant temperature with a thermometer.
NOTE: As the engine warms up to operating temperature, the actual coolant
temperature (thermometer reading) and the Eng Coolant Tmp Deg on the
DRBIIIt screen should stay relatively close to each other.
Using the appropriate service information, determine the proper opening tempera-
ture of the thermostat.
Did the thermostat open at the proper temperature?
Yes → Go To 3

No → Replace the thermostat.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

3 Ignition on, engine not running. All

With the DRBIIIt, read the Eng Coolant Tmp Deg value. If the engine was allowed
to sit overnight (cold soak), the temperature value should be a sensible value that is
somewhere close to the ambient temperature.
NOTE: If engine coolant temperature is above 82°C (180°F), allow the engine
to cool until 65°C (150°F) is reached.
Start the Engine.
During engine warm-up monitor the Eng Coolant Tmp Deg value. The temp deg
value change should be a smooth transition from start up to normal operating temp
82°C (180°F). Also monitor the actual coolant temperature with a thermometer.
NOTE: As the engine warms up to operating temperature, the actual coolant
temperature (thermometer reading) and the Eng Coolant Tmp Deg on the
DRBIIIt screen should stay relatively close to each other.
Is the thermometer reading relatively close to the DRBIIIt ECT reading?

Yes → Test Complete.

No → Replace the Engine Coolant Temperature Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

82
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0128-THERMOSTAT RATIONALITY

When Monitored and Set Condition:

P0128-THERMOSTAT RATIONALITY
When Monitored: Engine running.
Set Condition: The PCM predicts a coolant temperature value that it will compare to the
actual coolant temperature. A significant difference results in an error. Two Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
OTHER POSSIBLE CAUSES
LOW COOLANT LEVEL
THERMOSTAT OPERATION
SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
TEMPERATURE SENSOR
SIGNAL CIRCUIT OPEN
(K900) SENSOR GROUND CIRCUIT OPEN
SIGNAL CIRCUIT SHORTED TO GROUND
SIGNAL CIRCUIT SHORTED TO (K900) SENSOR GROUND
PCM

TEST ACTION APPLICABILITY

1 NOTE: If any ECT, AAT, CMP or CKP sensor DTCs have set along with P0128, All
diagnose them before continuing.
NOTE: Ensure that Pinion Factor has been programmed correctly into the
PCM.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

83
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0128-THERMOSTAT RATIONALITY — Continued

TEST ACTION APPLICABILITY

2 NOTE: If a Engine Coolant Temperature (ECT) DTC is set along with this All
code, diagnose the ECT DTC first.
NOTE: Inspect the ECT terminals and related PCM terminals. Make sure
the terminals are free from corrosion and damage.
NOTE: The best way to diagnose this DTC is to allow the vehicle to sit
overnight outside in order to have a totally cold soaked engine.
Note: Extremely cold outside ambient temperatures may have caused this
DTC to set.
WARNING: Never open the cooling system when the engine is hot. The
system is under pressure. Extreme burns or scalding may result. Allow the
engine to cool before opening the cooling system.
Check the coolant system to make sure that the coolant is in good condition and at
the proper level.
Is the coolant level and condition OK?
Yes → Go To 3

No → Inspect the vehicle for a coolant leak and add the necessary
amount of coolant.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

3 NOTE: This test works best if performed on a cold engine (cold soak). All
Ignition on, engine not running.
With the DRBIIIt, read the ECT Deg value. If the engine was allowed to sit overnight
(cold soak), the temperature value should be a sensible value that is somewhere close
to the ambient temperature.
Note: If engine coolant temperature is above 82°C (180°F), allow the engine
to cool until 65°C (150°F) is reached.
Start the Engine.
During engine warm-up, monitor the ECT Deg value. The temp deg value change
should be a smooth transition from start up to normal operating temp 82°C (180°F).
Also monitor the actual coolant temperature with a thermometer.
NOTE: As the engine warms up to operating temperature, the actual coolant
temperature (thermometer reading) and the ECT Deg on the DRBIIIt
screen should stay relatively close to each other.
Using the appropriate service information, determine the proper opening tempera-
ture of the thermostat.
Did the thermostat open at the proper temperature?

Yes → Go To 4

No → Replace the thermostat.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Ignition on, engine not running. All

With the DRBIIIt, read and record the AAT Sensor Temperature value.
Using the DRB Temperature Probe #CH7050, measure the ambient air temperature
near the AAT Sensor.
Is the AAT Sensor value with -15°C (5°F) of the temperature probe reading?

Yes → Go To 5

No → Go To 7

84
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0128-THERMOSTAT RATIONALITY — Continued

TEST ACTION APPLICABILITY

5 WARNING: MAKE SURE THE ENGINE COOLING SYSTEM IS COOL BE- All
FORE REMOVING THE PRESSURE CAP OR ANY HOSE. SEVERE PER-
SONAL INJURY MAY RESULT FROM ESCAPING HOT COOLANT. THE
COOLING SYSTEM IS PRESSURIZED WHEN HOT.
With the DRBIIIt, read and record the ECT Sensor Temperature value.
Using the DRB Temperature Probe #CH7050, measure the engine coolant tempera-
ture.
Is the ECT Sensor value with -15°C (5°F) of the temperature probe reading?

Yes → Go To 6
No → Go To 7

6 Inspect the Temperature sensors for any physical damage. All

Inspect the engine coolant. Make sure the coolant is at the proper level. Refer to the
Service Information COOLING.
Make sure the Temperature sensors are properly installed.
Make sure the CMP and CKP sensors are mounted properly. Check the connectors for
any signs of damage.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Refer to any Technical Service Bulletins (TSBs) that may apply.
With the engine running at normal operating temperature, monitor the Temperature
sensor parameters while wiggling the wire harness. Look for parameter values to
change.
Visually inspect the related wire harness. Look for any chafed, pierced, pinched,
partially broken wires and broken, bent, pushed out, or corroded terminals.
CAUTION: NEVER PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Inspect and clean all PCM, engine, and chassis grounds.
Were any problems found during the above inspections?
Yes → Repair as necessary
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Test Complete.

7 NOTE: Visually inspect both the component and the PCM connectors. Look All
for damage, partially broken wires and backed out or corroded terminals
Turn the ignition off.
Disconnect the applicable Temperature Sensor harness connector.
Disconnect the PCM harness connectors.
Ignition on, engine not running.
Measure the voltage of the Signal circuit in the appropriate Temperature Sensor
harness connector.
Is the voltage above 5.2 volts?
Yes → Repair the short to battery voltage in the Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 8

85
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0128-THERMOSTAT RATIONALITY — Continued

TEST ACTION APPLICABILITY

8 Connect a jumper wire across the Temperature Sensor harness connector. All
With the DRBIIIt, read the Temperature voltage.
Does the voltage start at 5.0 volts and drop below 1.0 volt?

Yes → Replace the suspected Temperature Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 9

9 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the Sensor Signal circuit from the Temperature Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 10
No → Repair the open in the Sensor Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

10 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the appropriate
Temperature Sensor harness connector to the appropriate terminal of special tool
#8815.
Is the resistance below 5.0 ohms?
Yes → Go To 11

No → Repair the open in the (K900) Sensor ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

11 Measure the resistance between ground and the Sensor Signal circuit in the All
Temperature Sensor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 12

12 Measure the resistance between the Signal circuit and the (K900) Sensor ground All
circuit at the Temperature Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short between the (K900) Sensor ground circuit and
the Sensor Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 13

86
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0128-THERMOSTAT RATIONALITY — Continued

TEST ACTION APPLICABILITY

13 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

87
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0129-BAROMETRIC PRESSURE OUT-OF-RANGE

When Monitored and Set Condition:

P0129-BAROMETRIC PRESSURE OUT-OF-RANGE

When Monitored: With the ignition key on. No Cam or Crank signal within 75 ms. Engine
speed less than 250 RPM.
Set Condition: The PCM senses the voltage from the MAP sensor to be less than 2.2 volts
but above 0.04 of a volt for 300 milliseconds. One Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
(F856) 5-VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE
(F856) 5-VOLT SUPPLY CIRCUIT OPEN
(F856) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
MAP SENSOR
(K1) MAP SIGNAL CIRCUIT OPEN
(K1) MAP SIGNAL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the MAP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the (F856) 5-volt Supply circuit at the MAP Sensor harness
connector.
Is the voltage between 4.5 to 5.2 volts?

Yes → Go To 3

No → Go To 6

88
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0129-BAROMETRIC PRESSURE OUT-OF-RANGE — Continued

TEST ACTION APPLICABILITY

3 With the DRBIIIt, monitor the MAP Sensor voltage with the Sensor harness All
connector disconnected.
Is the voltage above 4.5 volts?

Yes → Replace the MAP Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

4 Turn the ignition off. All

Disconnect the C1 and C2 PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K1) MAP Signal circuit from the MAP Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (K1) MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Measure the resistance between ground and the (K1) MAP Signal circuit at the MAP All
Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (K1) MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 9

6 Turn the ignition off. All

Disconnect the C1 and C2 PCM harness connectors.
Ignition on, engine not running.
Measure the voltage on the (F856) 5-volt Supply circuit at the MAP Sensor harness
connector.
Is the voltage above 5.2 volts?
Yes → Repair the short to voltage in the (F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 7

7 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (F856) 5-volt Supply circuit from the MAP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 8

No → Repair the open in the (F856) 5-volt Supply circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

89
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0129-BAROMETRIC PRESSURE OUT-OF-RANGE — Continued

TEST ACTION APPLICABILITY

8 Measure the resistance between ground and the (F856) 5-volt Supply circuit at the All
MAP Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 9

9 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

90
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom List:
P0131-O2 SENSOR 1/1 CIRCUIT LOW VOLTAGE
P0137-O2 SENSOR 1/2 CIRCUIT LOW VOLTAGE
P0151-O2 SENSOR 2/1 CIRCUIT LOW VOLTAGE
P0157-O2 SENSOR 2/2 CIRCUIT LOW VOLTAGE

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0131-O2 SENSOR 1/1 CIRCUIT
LOW VOLTAGE.

When Monitored and Set Condition:

P0131-O2 SENSOR 1/1 CIRCUIT LOW VOLTAGE

When Monitored: Engine running for less than 30 seconds and the O2 Sensor Heater
Temperature is less than 251°C (484°F) with battery voltage greater 10.4 volts.
Set Condition: The oxygen sensor signal voltage is below 2.411 volts for 10.24 seconds
after starting engine. One Trip Fault.

P0137-O2 SENSOR 1/2 CIRCUIT LOW VOLTAGE

When Monitored: Engine running for less than 30 seconds and the O2 Sensor Heater
Temperature is less than 251°C (484°F) with battery voltage greater 10.4 volts.
Set Condition: The oxygen sensor signal voltage is below 2.411 volts for 10.24 seconds
after starting engine. One Trip Fault.

P0151-O2 SENSOR 2/1 CIRCUIT LOW VOLTAGE

When Monitored: Engine running for less than 30 seconds and the O2 Sensor Heater
Temperature is less than 251°C (484°F) with battery voltage greater 10.4 volts.
Set Condition: The oxygen sensor signal voltage is below 2.411 volts for 10.24 seconds
after starting engine. One Trip Fault.

P0157-O2 SENSOR 2/2 CIRCUIT LOW VOLTAGE

When Monitored: Engine running for less than 30 seconds and the O2 Sensor Heater
Temperature is less than 251°C (484°F) with battery voltage greater 10.4 volts.
Set Condition: The oxygen sensor signal voltage is below 2.411 volts for 10.24 seconds
after starting engine. One Trip Fault.

POSSIBLE CAUSES
O2 SENSOR BELOW 2.52 VOLTS
O2 SENSOR
O2 RETURN CIRCUIT SHORTED TO GROUND
PCM

91
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0131-O2 SENSOR 1/1 CIRCUIT LOW VOLTAGE — Continued

TEST ACTION APPLICABILITY

1 Start the engine. All
Allow the engine to reach normal operating temperature.
NOTE: When diagnosing this DTC, diagnose the O2 Sensor that set the DTC.
With the DRBIIIt, read the O2 Sensor voltage.
Is the voltage below 2.52 volts?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the O2 Sensor harness connector.
Ignition on, engine not running.
With the DRBIIIt, monitor the O2 Sensor voltage.
Is the O2 Sensor voltage above 4.8 volts?

Yes → Go To 3
No → Go To 4

3 Measure the voltage on the O2 Return circuit at the O2 Sensor harness connector. All
Is the voltage at 2.5 volts?
Yes → Replace the O2 Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

4 Turn the ignition off. All

Disconnect the PCM harness connectors.
Measure the resistance between ground and the O2 Return circuit at the O2 Sensor
harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the O2 Return circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

92
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom List:
P0132-O2 SENSOR 1/1 CIRCUIT HIGH VOLTAGE
P0138-O2 SENSOR 1/2 CIRCUIT HIGH VOLTAGE
P0152-O2 SENSOR 2/1 CIRCUIT HIGH VOLTAGE
P0158-O2 SENSOR 2/2 CIRCUIT HIGH VOLTAGE

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0132-O2 SENSOR 1/1 CIRCUIT
HIGH VOLTAGE.

When Monitored and Set Condition:

P0132-O2 SENSOR 1/1 CIRCUIT HIGH VOLTAGE

When Monitored: O2 Sensor Heater Temperature is greater than 496°C (925°F) and
battery voltage greater than 10.4 volts.
Set Condition: The Oxygen Sensor voltage is above 3.99 volts for 66.56 seconds. One trip
fault.

P0138-O2 SENSOR 1/2 CIRCUIT HIGH VOLTAGE

When Monitored: O2 Sensor Heater Temperature is greater than 496°C (925°F) and
battery voltage greater than 10.4 volts.
Set Condition: The Oxygen Sensor voltage is above 3.99 volts for 76.8 seconds. One trip
fault.

P0152-O2 SENSOR 2/1 CIRCUIT HIGH VOLTAGE

When Monitored: O2 Sensor Heater Temperature is greater than 496°C (925°F) and
battery voltage greater than 10.4 volts.
Set Condition: The Oxygen Sensor voltage is above 3.99 volts for 66.56 seconds. One trip
fault.

P0158-O2 SENSOR 2/2 CIRCUIT HIGH VOLTAGE

When Monitored: O2 Sensor Heater Temperature is greater than 496°C (925°F) and
battery voltage greater than 10.4 volts.
Set Condition: The Oxygen Sensor voltage is above 3.99 volts for 76.8 seconds. One trip
fault.

POSSIBLE CAUSES
O2 SENSOR VOLTAGE ABOVE 3.7 VOLTS
O2 SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
O2 SENSOR RETURN CIRCUIT SHORTED TO VOLTAGE
O2 SENSOR

93
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0132-O2 SENSOR 1/1 CIRCUIT HIGH VOLTAGE — Continued

POSSIBLE CAUSES
O2 SENSOR SIGNAL CIRCUIT OPEN
O2 SENSOR RETURN CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 NOTE: If one of the O2 Sensors Signal or Return circuits are shorted to All
voltage, the DRBIIIt will display all O2 Sensor voltage readings high.
NOTE: It is important to perform the diagnostics on the O2 Sensor that set
the DTC.
NOTE: After the repairs have been made, verify proper O2 Sensor operation.
If all the O2 Sensor voltage readings have not returned to normal, follow the
diagnostic procedure for the remaining O2 Sensors.
Start the engine.
Allow the engine to reach normal operating temperature.
With the DRBIIIt, read the O2 Sensor voltage.
Is the voltage above 3.7 volts?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the O2 Sensor harness connector
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Start the engine and allow the engine to idle.
Measure the voltage on the O2 Sensor Signal circuit in the O2 Sensor harness
connector.
NOTE: Measure the voltage in reference to ground, not the O2 Sensor
Return circuit.
Is the voltage above 5.2 volts?
Yes → Repair the short to voltage in the O2 Sensor Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 3

3 Turn the ignition off. All

Disconnect the PCM harness connectors.
Ignition on, engine not running.
Measure the voltage on the O2 Sensor Return circuit in the O2 Sensor harness
connector.
Is there any voltage present?

Yes → Repair the short to voltage in the O2 Sensor Return circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

94
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0132-O2 SENSOR 1/1 CIRCUIT HIGH VOLTAGE — Continued

TEST ACTION APPLICABILITY

4 Turn the ignition off. All
Connect the PCM harness connectors.
Connect a jumper wire between the O2 Sensor Signal circuit and the O2 Sensor
Return circuit in the O2 Sensor harness connector.
Ignition on, engine not running.
With the DRBIIIt, monitor the O2 Sensor voltage.
Is the voltage between 2.3 and 2.7 volts with the jumper wire in place?

Yes → Replace the O2 Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

NOTE: Remove the jumper wire before continuing.

5 Turn the ignition off. All

Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the O2 Sensor Signal circuit from the O2 Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6

No → Repair the open O2 Sensor Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Measure the resistance of the O2 Sensor Return circuit from the O2 Sensor harness All
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 7
No → Repair the open O2 Sensor Return circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

95
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom List:
P0133-O2 SENSOR 1/1 SLOW RESPONSE
P0139-O2 SENSOR 1/2 SLOW RESPONSE
P0153-O2 SENSOR 2/1 SLOW RESPONSE
P0159-O2 SENSOR 2/2 SLOW RESPONSE

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0133-O2 SENSOR 1/1 SLOW
RESPONSE.

When Monitored and Set Condition:

P0133-O2 SENSOR 1/1 SLOW RESPONSE

When Monitored: Vehicle is started and driven between 20 and 55 MPH with the Throttle
open for a minimum of 120 seconds. Coolant greater than 70°C (158°F). Catalytic
Converter Temp greater than 600°C (1112°F) and EVAP Purge is active.
Set Condition: The oxygen sensor signal voltage switches less than 16 times from lean to
rich within 20 seconds during monitoring. Two Trip Fault.

P0139-O2 SENSOR 1/2 SLOW RESPONSE

When Monitored: Vehicle is started and driven between 20 and 55 MPH with the Throttle
open for a minimum of 120 seconds. Coolant greater than 70°C (158°F). Catalytic
Converter Temp greater than 600°C (1112°F) and EVAP Purge is active
Set Condition: The oxygen sensor signal voltage switches less than 16 times from lean to
rich within 20 seconds during monitoring. Two Trip Fault.

P0153-O2 SENSOR 2/1 SLOW RESPONSE

When Monitored: Vehicle is started and driven between 20 and 55 MPH with the Throttle
open for a minimum of 120 seconds. Coolant greater than 70°C (158°F). Catalytic
Converter Temp greater than 600°C (1112°F) and EVAP Purge is active
Set Condition: The oxygen sensor signal voltage switches less than 16 times from lean to
rich within 20 seconds during monitoring. Two Trip Fault.

P0159-O2 SENSOR 2/2 SLOW RESPONSE

When Monitored: Vehicle is started and driven between 20 and 55 MPH with the Throttle
open for a minimum of 120 seconds. Coolant greater than 70°C (158°F). Catalytic
Converter Temp greater than 600°C (1112°F) and EVAP Purge is active
Set Condition: The oxygen sensor signal voltage switches less than 16 times from lean to
rich within 20 seconds during monitoring. Two Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO

96
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0133-O2 SENSOR 1/1 SLOW RESPONSE — Continued

POSSIBLE CAUSES
EXHAUST LEAK
O2 SIGNAL CIRCUIT
O2 RETURN CIRCUIT
O2 SENSOR

TEST ACTION APPLICABILITY

1 NOTE: Check for contaminants that may have damaged the O2 Sensor: All
contaminated fuel, unapproved silicone, oil and coolant.
Ignition on, engine not running.
NOTE: After the repairs have been made, verify proper O2 Sensor operation.
If all the O2 Sensor voltage readings have not returned to normal, follow the
diagnostic procedure for the remaining O2 Sensors.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Start the engine. All

Inspect the exhaust system for leaks between the engine and the O2 Sensors.
Are there any exhaust leaks?
Yes → Repair or replace the leaking exhaust parts as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 3

3 Turn the ignition off All

Disconnect the O2 Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the O2 Signal circuit in the O2 Sensor harness connector.
Is the voltage between 4.5 and 5.0 volts?

Yes → Go To 4

No → Check the O2 Signal circuit for damage, short to ground, open, or

short to voltage. If OK, replace and program the Powertrain
Control Module per Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Measure the voltage on the O2 Return circuit in the O2 Sensor harness connector. All
Is the voltage at 2.5 volts?

Yes → Check the O2 Return circuit for damage, short to ground, open, or
short to voltage. If OK, replace and program the Powertrain
Control Module per Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 If there are no possible causes remaining, view repair. All

Repair
Replace the O2 Sensor
Perform POWERTRAIN VERIFICATION TEST VER - 5.

97
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom List:
P0135-O2 SENSOR 1/1 HEATER PERFORMANCE
P0141-O2 SENSOR 1/2 HEATER PERFROMANCE
P0155-O2 SENSOR 2/1 HEATER PERFORMANCE
P0161-O2 SENSOR 2/2 HEATER PERFORMANCE

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0135-O2 SENSOR 1/1 HEATER
PERFORMANCE.

When Monitored and Set Condition:

P0135-O2 SENSOR 1/1 HEATER PERFORMANCE

When Monitored: Engine running and heater duty cycle greater than 0%. ASD Relay is
energized. Battery voltage greater than 10.4 volts.
Set Condition: No sensor output is received when the PCM powers up the sensor heater.
O2 heater is out of control for 128 seconds after it has reached 300 deg C. Two trip fault

P0141-O2 SENSOR 1/2 HEATER PERFROMANCE

When Monitored: Engine running and heater duty cycle greater than 0%. ASD Relay is
energized. Battery voltage greater than 10.4 volts.
Set Condition: No sensor output is received when the PCM powers up the sensor heater.
O2 heater is out of control for 128 seconds after it has reached 350 deg C. Two trip fault.

P0155-O2 SENSOR 2/1 HEATER PERFORMANCE

When Monitored: Engine running and heater duty cycle greater than 0%. ASD Relay is
energized. Battery voltage greater than 10.4 volts.
Set Condition: No sensor output is received when the PCM powers up the sensor heater.
O2 heater is out of control for 128 seconds after it has reached 300 deg C. Two trip fault.

P0161-O2 SENSOR 2/2 HEATER PERFORMANCE

When Monitored: Engine running and heater duty cycle greater than 0%. ASD Relay is
energized. Battery voltage greater than 10.4 volts.
Set Condition: No sensor output is received when the PCM powers up the sensor heater.
O2 heater is out of control for 128 seconds after it has reached 350 deg C. Two trip fault.

POSSIBLE CAUSES
O2 SENSOR HEATER OPERATION
O2 HEATER ELEMENT
O2 HEATER CONTROL CIRCUIT OPEN
O2 HEATER GROUND CIRCUIT OPEN

98
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0135-O2 SENSOR 1/1 HEATER PERFORMANCE — Continued

POSSIBLE CAUSES
PCM

TEST ACTION APPLICABILITY

1 Turn the ignition off. All
NOTE: Wait a minimum of 8 minutes to allow the O2 Sensor to cool down
before continuing the test. Allow the O2 Sensor voltage to stabilize between
4.6 and 5.0 volts.
Ignition on, engine not running.
With the DRBIIIt, actuate the O2 Heater Test.
With the DRBIIIt, monitor O2 Sensor voltage for at least 2 minutes.
Does the voltage stay above 4.5 volts?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

NOTE: Allow the O2 Sensor to cool down to room temperature.
Disconnect the O2 Sensor harness connector.
Measure the resistance across the O2 Sensor Heater element component side.
Is the resistance between 2.0 and 30 ohms?
Yes → Go To 3

No → Replace the O2 Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

3 Disconnect the PCM harness connectors. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the O2 Heater Control circuit from the O2 Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 0.5 of an ohm?
Yes → Go To 4

No → Repair the excessive resistance in the O2 Heater Control circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Measure the resistance between an engine ground and the O2 Heater ground circuit All
at the O2 Sensor harness connector.
Is the resistance below 0.5 of an ohm?
Yes → Go To 5

No → Repair the excessive resistance in the O2 Heater ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

99
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0135-O2 SENSOR 1/1 HEATER PERFORMANCE — Continued

TEST ACTION APPLICABILITY

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

100
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom List:
P0171-FUEL SYSTEM 1/1 LEAN
P0174-FUEL SYSTEM 2/1 LEAN

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0171-FUEL SYSTEM 1/1 LEAN.

When Monitored and Set Condition:

P0171-FUEL SYSTEM 1/1 LEAN

When Monitored: With the engine running in closed loop mode, the ambient/battery
temperature above 20 deg. F and altitude below 8500 ft.
Set Condition: If the PCM multiplies short term compensation by long term adaptive and
a certain percentage is exceeded for two trips, a freeze frame is stored, the MIL illuminates
and a trouble code is stored.

P0174-FUEL SYSTEM 2/1 LEAN

When Monitored: With the engine running in closed loop mode, the ambient/battery
temperature above 20 deg. F and altitude below 8500 ft.
Set Condition: If the PCM multiplies short term compensation by long term adaptive and
a certain percentage is exceeded for two trips, a freeze frame is stored, the MIL illuminates
and a trouble code is stored.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
RESTRICTED FUEL SUPPLY LINE
FUEL PUMP INLET STRAINER PLUGGED
FUEL PUMP MODULE
O2 SENSOR
O2 SIGNAL CIRCUIT
O2 RETURN CIRCUIT
O2 SENSOR HEATER OPERATION
THROTTLE POSITION SENSOR VOLTAGE GREATER THAN 0.92 VOLTS WITH THROTTLE
CLOSED
THROTTLE POSITION SENSOR SWEEP
MAP SENSOR
ECT SENSOR
ENGINE MECHANICAL PROBLEM
FUEL FILTER/PRESSURE REGULATOR (HIGH)
PCM

101
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0171-FUEL SYSTEM 1/1 LEAN — Continued

TEST ACTION APPLICABILITY

1 Diagnose all other trouble codes before continuing. All
NOTE: Check for contaminants that may have damaged an O2 Sensor:
contaminated fuel, unapproved silicone, oil and coolant.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 WARNING: The fuel system is under constant pressure (even with the All
engine off). Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Install a fuel pressure gauge to the fuel rail.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Fuel System test and observe the fuel pressure
gauge.
NOTE: Fuel pressure specification is 407 KPa +/- 34 KPa (59 psi +/- 5 psi).
Turn the ignition off.
Choose a conclusion that best matches your fuel pressure reading.
Within Specification
Go To 3
Above Specification
Replace the fuel filter/pressure regulator.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
Below Specification
Go To 13
Caution: Stop All Actuations.

3 Start the engine. All

Allow the engine to reach normal operating temperature.
NOTE: If one of the O2 Sensors Signal or Return circuit is shorted to ground
the DRBIIIt will display all O2 Sensor voltage readings low. The O2 Sensor
that is shorted to ground will display a voltage reading near or at 0 volts.
NOTE: If one of the O2 Sensors Signal or Return circuit is shorted to
voltage, the DRBIIIt will display all O2 Sensor voltage readings high. It is
important to diagnose the O2 Sensor that set the DTC.
NOTE: After the repairs have been made, verify proper O2 Sensor operation.
If all the O2 Sensor voltage readings have not returned to normal, follow the
diagnostic procedure for the remaining O2 Sensors.
With the DRBIIIt, monitor all the O2 Sensor voltage readings.
Is the voltage switching between 2.5 and 3.4 volts for all of the O2 Sensors?

Yes → Go To 4

No → Go To 10

102
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0171-FUEL SYSTEM 1/1 LEAN — Continued

TEST ACTION APPLICABILITY

4 Turn the ignition off. All
NOTE: Wait a minimum of 10 minutes to allow the O2 Sensor to cool down
before continuing the test. Allow the O2 Sensor voltage to stabilize at 5.0
volts.
NOTE: Perform the following test on all O2 Sensors.
Ignition on, engine not running.
With the DRBIIIt, actuate the O2 Heater Test.
With the DRBIIIt, monitor O2 Sensor voltage for at least 2 minutes.
Does the voltage stay above 4.5 volts?

Yes → Replace the O2 Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 With the DRBIIIt, read TP Sensor voltage. All

NOTE: The throttle must be against the stop.
Is the voltage 0.92 or less with the Throttle closed?
Yes → Go To 6
No → Check for a binding throttle condition. If OK, replace the Throttle
Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 With the DRBIIIt, read the TP Sensor voltage. All

While monitoring the DRBIIIt, slowly open and close the throttle.
Does the voltage increase and decrease smoothly?

Yes → Go To 7
No → Replace the Throttle Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Turn the ignition off. All

Connect a Vacuum Gauge to a Manifold Vacuum source.
Start the engine.
Allow the engine to idle.
NOTE: If engine will not idle, maintain a constant RPM above idle.
With the DRBIIIt in Sensors, read the MAP Sensor vacuum value.
Is the DRBIIIt reading within 19 of the Vacuum Gauge reading?

Yes → Go To 8

No → Replace the MAP Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

103
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0171-FUEL SYSTEM 1/1 LEAN — Continued

TEST ACTION APPLICABILITY

8 NOTE: For this test to be valid, the thermostat must be operating correctly. All
NOTE: This test works best if performed on a cold engine (cold soak)
Ignition on, engine not running.
With the DRBIIIt, read the Engine Coolant Temperature (ECT) Sensor value. If the
engine was allowed to sit overnight (cold soak), the temperature value should be a
sensible value that is somewhere close to the ambient temperature.
NOTE: If engine coolant temperature is above 82°C (180°F), allow the engine
to cool until 65°C (150°F) is reached.
Start the Engine.
During engine warm-up, monitor the ECT Sensor value. The temperature value
change should be a smooth transition from start up to normal operating temperature
82°C (180°F). The value should reach at least 82°C (180°F).
Did the ECT value increase smoothly and did it reach at least 180°F (82°C)??

Yes → Go To 9
No → Replace the Engine Coolant Temperature Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

9 Turn the ignition off. All

Check for any of the following conditions/mechanical problems.
AIR INDUCTION SYSTEM - must be free from leaks.
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions or leaks.
ENGINE PCV SYSTEM - must flow freely
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to
correct injector
Are there any engine mechanical problems?
Yes → Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 12

10 Ignition on, engine not running. All

NOTE: Perform the following test on the O2 Sensors whose voltage was not
switching properly in the previous step.
Disconnect the O2 Sensor harness connector.
With the DRBIIIt, monitor the O2 Sensor voltage.
O2 Sensor voltage should read 5.0 volts on the DRBIIIt with the connector
disconnected.
Connect a jumper wire between the O2 Signal circuit and the O2 Return circuit in the
O2 Sensor harness connector.
NOTE: The voltage should drop from 5.0 volts to 2.5 volts with the jumper
wire in place.
Did the O2 Sensor voltage change from 5.0 volts to 2.5 volts?

Yes → Replace the O2 Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 11
NOTE: Remove the jumper wire before continuing.

104
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0171-FUEL SYSTEM 1/1 LEAN — Continued

TEST ACTION APPLICABILITY

11 Only have one O2 Sensor disconnect at a time. All
With the DRBIIIt, monitor all the O2 Sensor voltage readings.
NOTE: The DRBIIIt will display all O2 Sensor voltage readings approxi-
mately 5.0 volts when only one O2 Sensor’s Signal circuit is shorted to
voltage.
NOTE: The DRBIIIt will display one O2 Sensor voltage close to zero and the
others will read lower than normal when one O2 Sensor Signal circuit
contains excessive resistance.
Is the voltage above 4.8 volts?

Yes → Go To 12

No → Check all the O2 Signal circuits for a short to ground, open, or

short to voltage. Inspect the O2 Sensor connector and the PCM
harness connector. If OK, replace and program the Powertrain
Control Module per Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

12 Disconnect each O2 Sensor harness connector. All

Measure the voltage on the O2 Return circuits in the O2 Sensor harness connector.
NOTE: The DRBIIIt will display all O2 Sensor voltage readings approxi-
mately 5.0 volts when only one O2 Sensor’s Return circuit is shorted to
voltage.
NOTE: The DRBIIIt will display one O2 Sensor voltage close to zero and the
others will read lower than normal when one O2 Sensor Return circuit
contains excessive resistance.
Is the voltage at 2.5 volts?
Yes → Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Check all the O2 Return circuits for a short to ground, open, or
short to voltage. Inspect the O2 Sensor connector and the PCM
harness connector. If OK, replace and program the Powertriain
Control Module per Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

13 Turn the ignition off. All

WARNING: The fuel system is under a constant pressure (even with the
engine off). Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Raise vehicle on hoist, and disconnect the fuel pressure line at the fuel pump module.
Install special 5/16 fuel line adapter tool #6539 between disconnected fuel line and
the fuel pump module.
Attach a fuel pressure test gauge to the T fitting on tool #6539.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Fuel System test and observe the fuel pressure
gauge.
NOTE: Fuel pressure specification is 407 KPa +/- 34 KPa (59 psi +/- 5 psi).
Is the fuel pressure within specification?

Yes → Repair or replace fuel supply line as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 14
CAUTION: Stop All Actuations.

105
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0171-FUEL SYSTEM 1/1 LEAN — Continued

TEST ACTION APPLICABILITY

14 Turn the ignition off. All
WARNING: The fuel system is under a constant pressure (even with the
engine off). Before testing or servicing any fuel system hose,fitting or line,
the fuel system pressure must be released.
Remove the Fuel Pump Module and inspect the Fuel Inlet Strainer.
Is the Fuel Inlet Strainer plugged?

Yes → Replace the Fuel Pump Inlet Strainer.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 15

15 If there are no possible causes remaining, view repair. All

Repair
Replace the Fuel Pump Module.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

106
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom List:
P0172-FUEL SYSTEM 1/1 RICH
P0175-FUEL SYSTEM 2/1 RICH

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0172-FUEL SYSTEM 1/1 RICH.

When Monitored and Set Condition:

P0172-FUEL SYSTEM 1/1 RICH

When Monitored: With the engine running in closed loop mode, the ambient/battery
temperature above 20 deg. F and altitude below 8500 ft.
Set Condition: If the PCM multiplies short term compensation by long term adaptive and
a purge fuel multiplier and the result is below a certain value for 30 seconds over two trips,
a freeze frame is stored, the MIL illuminates and a trouble code is stored.

P0175-FUEL SYSTEM 2/1 RICH

When Monitored: With the engine running in closed loop mode, the ambient/battery
temperature above 20 deg. F and altitude below 8500 ft.
Set Condition: If the PCM multiplies short term compensation by long term adaptive and
a purge fuel multiplier and the result is below a certain value for 30 seconds over two trips,
a freeze frame is stored, the MIL illuminates and a trouble code is stored.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
O2 SENSOR HEATER OPERATION
O2 SENSOR
O2 SIGNAL CIRCUIT
O2 RETURN CIRCUIT
THROTTLE POSITION SENSOR VOLTAGE GREATER THAN 0.92 VOLTS WITH THROTTLE
CLOSED
THROTTLE POSITION SENSOR SWEEP
MAP SENSOR
ECT SENSOR
EVAP PURGE SOLENOID OPERATION
ENGINE MECHANICAL PROBLEM
FUEL FILTER/PRESSURE REGULATOR (HIGH)
PCM

107
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0172-FUEL SYSTEM 1/1 RICH — Continued

TEST ACTION APPLICABILITY

1 NOTE: Check for contaminants that may have damaged the O2 Sensor: All
contaminated fuel, unapproved silicone, oil and coolant.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 WARNING: The fuel system is under a constant pressure (even with the All
engine off). Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Install a fuel pressure gauge to the fuel rail.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Fuel System test and observe the fuel pressure
gauge.
NOTE: Fuel pressure specification is 407 KPa +/- 34 KPa (59 psi +/- 5 psi).
Turn the ignition off.
Choose a conclusion that best matches your fuel pressure reading.
Within Specification
Go To 3
Above Specification
Replace the fuel filter/pressure regulator.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
CAUTION: Stop All Actuations.

3 Start the engine. All

Allow the engine to reach normal operating temperature.
NOTE: If one of the O2 Sensors Signal or Return circuit is shorted to ground
or voltage, all the other O2 Sensor voltage readings will be affected. It is
important to diagnose the O2 Sensor that set the DTC.
NOTE: After the repairs have been made, verify proper O2 Sensor operation.
If all the O2 Sensor voltage readings have not returned to normal, follow the
diagnostic procedure for the remaining O2 Sensors.
With the DRBIIIt, monitor all of the O2 Sensor voltage readings.
Is the voltage switching between 2.5 and 3.4 volts?
Yes → Go To 4

No → Go To 11

4 Turn the ignition off. All

NOTE: Wait a minimum of 10 minutes to allow the O2 Sensor to cool down
before continuing the test. Allow the O2 Sensor voltage to stabilize at 5.0
volts.
Ignition on, engine not running.
With the DRBIIIt, perform the O2 Heater Test for each of the O2 Sensors.
With the DRBIIIt, monitor all O2 Sensor voltage readings for at least 2 minutes.
Does the voltage stay above 4.5 volts?
Yes → Replace the O2 Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

108
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0172-FUEL SYSTEM 1/1 RICH — Continued

TEST ACTION APPLICABILITY

5 Ignition on, engine not running. All
With the DRBIIIt, read the TP Sensor voltage.
NOTE: The throttle must be against the stop.
Is the TP Sensor voltage 0.92 of a volt or less with the Throttle closed?
Yes → Go To 6

No → Check for a binding throttle condition. If OK, replace the Throttle

Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 With the DRBIIIt, read the TP Sensor voltage. All

While monitoring the DRBIIIt, slowly open and close the throttle.
Does the voltage increase and decrease smoothly?

Yes → Go To 7
No → Replace the Throttle Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Turn the ignition off. All

Connect a Vacuum Gauge to a Manifold Vacuum source.
Start the engine.
Allow the engine to idle.
NOTE: If engine will not idle, maintain a constant RPM above idle.
With the DRBIIIt in Sensors, read the MAP Sensor vacuum value.
Is the DRB reading within 19 of the Vacuum Gauge reading?

Yes → Go To 8
No → Replace the MAP Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
NOTE: Remove the vacuum gauge before continuing.

8 NOTE: For this test to be valid, the thermostat must be operating correctly. All
NOTE: This test works best if performed on a cold engine (cold soak)
Ignition on, engine not running.
With the DRBIIIt, read the ECT Sensor value. If the engine was allowed to sit
overnight (cold soak), the temperature value should be a sensible value that is
somewhere close to the ambient temperature.
NOTE: If engine coolant temperature is above 82°C (180°F), allow the engine
to cool until 65°C (150°F) is reached.
Start the Engine.
During engine warm-up, monitor the ECT Sensor value. The temp value change
should be a smooth transition from start up to normal operating temp 82°C (180°F).
The value should reach at least 82°C (180°F).
Did the ECT value increase smoothly and did it reach at least 180°F (82°C)?

Yes → Go To 9

No → Replace the Engine Coolant Temperature Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

109
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0172-FUEL SYSTEM 1/1 RICH — Continued

TEST ACTION APPLICABILITY

9 Turn the ignition off. All
Disconnect the hoses at the Evap Purge Solenoid.
Using a hand vacuum pump, apply 10 inches of vacuum to the Evap Purge Solenoid
vacuum source port on the component side.
Did the Evap Purge Solenoid hold vacuum?

Yes → Go To 10

No → Replace the EVAP Purge Solenoid.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
NOTE: Connect the vacuum hoses before continuing.

10 Check for any of the following conditions/mechanical problems. All

AIR INDUCTION SYSTEM - must be free from restrictions.
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions or leaks.
ENGINE PCV SYSTEM - must flow freely
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to
correct injector
Are there any engine mechanical problems?

Yes → Repair as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 14

11 Ignition on, engine not running. All

NOTE: Perform the following test on the O2 Sensors whose voltage was not
switching properly in the previous step.
Disconnect the O2 Sensor harness connector.
With the DRBIIIt, monitor the O2 Sensor voltage.
O2 Sensor voltage should read 5.0 volts on the DRBIIIt with the connector
disconnected.
Connect a jumper wire between the O2 Signal circuit and the O2 Return circuit in the
O2 Sensor harness connector.
NOTE: The voltage should drop from 5.0 volts down to 2.5 volts with the
jumper wire connected.
Did the O2 Sensor voltage drop from 5.0 volts to 2.5 volts?

Yes → Replace the O2 Sensor

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 12

NOTE: Remove the jumper wire before continuing.

110
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0172-FUEL SYSTEM 1/1 RICH — Continued

TEST ACTION APPLICABILITY

12 WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A All
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Start the engine.
Measure the voltage on the O2 Sensor Signal circuit in the O2 Sensor harness
connector with the Sensor harness connector disconnected.
Is the voltage above 4.8 volts?

Yes → Check the O2 Signal circuit for damage, short to ground, open, or
short to voltage. Inspect the O2 Sensor connector and the PCM
harness connector. If OK, replace the Powertrain Control Module
per Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 13

13 Engine still running. All

Measure the voltage on the O2 Return circuit in the O2 Sensor harness connector.
Is the voltage at 2.5 volts?
Yes → Go To 14
No → Check the O2 Return circuit for damage, short to ground, open, or
short to voltage. Inspect the O2 Sensor connector and the PCM
harness connector. If OK, replace the Powertrain Control Module
per Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

NOTE: Turn the ignition off before continuing.

14 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

111
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom List:
P0201-FUEL INJECTOR NO.1 CIRCUIT
P0202-FUEL INJECTOR NO.2 CIRCUIT
P0203-FUEL INJECTOR NO.3 CIRCUIT
P0204-FUEL INJECTOR NO.4 CIRCUIT
P0205-FUEL INJECTOR NO.5 CIRCUIT
P0206-FUEL INJECTOR NO.6 CIRCUIT

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0201-FUEL INJECTOR NO.1
CIRCUIT.

When Monitored and Set Condition:

P0201-FUEL INJECTOR NO.1 CIRCUIT

When Monitored: With battery voltage greater than 11.9981 volts. Auto Shutdown Relay
energized. Engine speed less than 3008 rpm.
Set Condition: No inductive spike is detected after injector turn off.

P0202-FUEL INJECTOR NO.2 CIRCUIT

When Monitored: With battery voltage greater than 11.9981 volts. Auto Shutdown Relay
energized. Engine speed less than 3008 rpm.
Set Condition: No inductive spike is detected after injector turn off.

P0203-FUEL INJECTOR NO.3 CIRCUIT

When Monitored: With battery voltage greater than 11.9981 volts. Auto Shutdown Relay
energized. Engine speed less than 3008 rpm.
Set Condition: No inductive is detected after injector turn off.

P0204-FUEL INJECTOR NO.4 CIRCUIT

When Monitored: With battery voltage greater than 11.9981 volts. Auto Shutdown Relay
energized. Engine speed less than 3008 rpm.
Set Condition: No inductive spike is detected after injector turn off, and with no other
injectors on.

P0205-FUEL INJECTOR NO.5 CIRCUIT

When Monitored: With battery voltage greater than 11.9981 volts. Auto Shutdown Relay
energized. Engine speed less than 3008 rpm.
Set Condition: No inductive spike is detected after injector turn off.

112
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0201-FUEL INJECTOR NO.1 CIRCUIT — Continued

P0206-FUEL INJECTOR NO.6 CIRCUIT

When Monitored: With battery voltage greater than 11.9981 volts. Auto Shutdown Relay
energized. Engine speed less than 3008 rpm.
Set Condition: No inductive spike is detected after injector turn off.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
(F142), (K334) ASD RELAY OUTPUT CIRCUIT
FUEL INJECTOR
INJECTOR CONTROL CIRCUIT OPEN
INJECTOR CONTROL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 NOTE: (F142) is the ASD Relay Output circuit on the 2.4L and (K334) is the All
ASD Relay Output on the 4.0L.
Turn the ignition off.
Disconnect the Fuel Injector harness connector.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Relay.
Using a 12-volt test light connected to ground, backprobe the (F142), (K334) ASD
Relay Output circuit at the Fuel Injector harness connector.
Does the test light illuminate brightly?

Yes → Go To 3

No → Repair the open or short to ground in the (F142), (K334) ASD

Relay Output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

113
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0201-FUEL INJECTOR NO.1 CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Using a 12-volt test light connected to 12-volts, backprobe the Injector Control All
circuit.
With the DRBIIIt, actuate the Fuel Injector.
What is the state of the test light during the actuation?
Brightly blinking.
Replace the Fuel Injector.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
ON constantly.
Go To 4

OFF constantly.
Go To 5

4 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Measure the resistance between ground and the Injector Control circuit at the
Injector harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the Injector Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

5 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the Injector Control circuit from the Fuel Injector harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6

No → Repair the open in the Injector Control circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

114
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom List:
P0300-MULTIPLE CYLINDER MISFIRE
P0301-CYLINDER NO.1 MISFIRE
P0302-CYLINDER NO.2 MISFIRE
P0303-CYLINDER NO.3 MISFIRE
P0304-CYLINDER NO.4 MISFIRE
P0305-CYLINDER NO.5 MISFIRE
P0306-CYLINDER NO.6 MISFIRE

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0300-MULTIPLE CYLINDER
MISFIRE.

When Monitored and Set Condition:

P0300-MULTIPLE CYLINDER MISFIRE

When Monitored: Any time the engine is running, and the adaptive numerator has been
successfully updated.
Set Condition: When more than a 2% (2.5% LEV) misfire rate is measured during two
trips. Above 3000 RPM 1 trip less than 3000 RPM 2 trip.

P0301-CYLINDER NO.1 MISFIRE

When Monitored: Any time the engine is running, and the adaptive numerator has been
successfully updated.
Set Condition: When more than a 2% (2.5% LEV) misfire rate is measured during two
trips, or with a 10% to 30% misfire rate during one trip.

P0302-CYLINDER NO.2 MISFIRE

When Monitored: Any time the engine is running, and the adaptive numerator has been
successfully updated.
Set Condition: When more than a 2% (2.5% LEV) misfire rate is measured during two
trips, or with a 10% to 30% misfire rate during one trip.

P0303-CYLINDER NO.3 MISFIRE

When Monitored: Any time the engine is running, and the adaptive numerator has been
successfully updated.
Set Condition: When more than a 2% (2.5% LEV) misfire rate is measured during two
trips, or with a 10% to 30% misfire rate during one trip.

P0304-CYLINDER NO.4 MISFIRE

When Monitored: Any time the engine is running, and the adaptive numerator has been
successfully updated.
Set Condition: When more than a 2% (2.5% LEV) misfire rate is measured during two
trips, or with a 10% to 30% misfire rate during one trip.

115
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0300-MULTIPLE CYLINDER MISFIRE — Continued

P0305-CYLINDER NO.5 MISFIRE

When Monitored: Any time the engine is running, and the adaptive numerator has been
successfully updated.
Set Condition: When more than a 2% (2.5% LEV) misfire rate is measured during two
trips, or with a 10% to 30% misfire rate during one trip.

P0306-CYLINDER NO.6 MISFIRE

When Monitored: Any time the engine is running, and the adaptive numerator has been
successfully updated.
Set Condition: When more than a 2% (2.5% LEV) misfire rate is measured during two
trips, or with a 10% to 30% misfire rate during one trip.

POSSIBLE CAUSES
INTERMITTENT MISFIRE
VISUAL INSPECTION
(F142), (K334) ASD RELAY OUPUT CIRCUIT
ENGINE MECHANICAL PROBLEM
IGNITION COIL
COIL CONTROL CIRCUIT
SPARK PLUG
CHECKING FUEL PRESSURE
FUEL PUMP INLET STRAINER PLUGGED
RESTRICTED FUEL SUPPLY LINE
FUEL PUMP MODULE
CHECKING FUEL LEAK DOWN
FUEL INJECTOR
INJECTOR CONTROL CIRCUIT
PCM

116
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0300-MULTIPLE CYLINDER MISFIRE — Continued

TEST ACTION APPLICABILITY

1 NOTE: Check for any TSBs that apply to a Misfire condition. Review the All
vehicle repair history for any misfire condition repairs that have been
performed.
Read and record the FREEZE FRAME DATA. Select OBD II MONITORS. Read and
record the MIS-FIRE SIMILAR CONDITIONS WINDOW DATA.
With these screens, attempt to duplicate the condition(s) that has set this DTC.
When the vehicle is operating in the SIMILAR CONDITIONS WINDOW, refer to the
WHICH CYLINDER IS MISFIRING screen.
Observe the WHICH CYLINDER IS MISFIRING screen for at least one minute.
Is there a misfire present?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 NOTE: Anything that affects the speed of the crankshaft can cause a misfire All
DTC.
NOTE: When a Misfire is detected for a particular cylinder, the PCM will
shut down that cylinders Injector Control circuit.
- Visually inspect the engine for any of the following conditions.
- Worn serpentine belt
- Binding Engine-Driven accessories: A/C Compressor, P/S Pump, Water pump.
- Misalignment Water pump, P/S Pump and A/C Compressor pulleys
- Corroded PCM power and ground circuits.
- Improper CKP, CMP, MAP, and TP Sensor mounting
- Poor connector/terminal to component connection. i.e., CKP sensor, Fuel Injector,
Ign coil, etc.
- Vacuum leaks
- Restricted Air Induction system or Exhaust system.
- Internal engine component failures.
Were any of the above conditions present?
Yes → Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

3 Turn the ignition off. All

Disconnect the Ignition Coil harness connector and Fuel Injector harness connector
of the cylinder being tested.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Relay.
Using a 12-volt test light connected to ground, probe the (F142), (K334) ASD Relay
Output circuit at the Ignition Coil harness connector and Fuel Injector harness
connector.
Does the test light illuminate brightly?

Yes → Go To 4

No → Repair the excessive resistance or short to ground in the (F142),

(K334) ASD Relay Output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

117
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0300-MULTIPLE CYLINDER MISFIRE — Continued

TEST ACTION APPLICABILITY

4 Turn the ignition off. All
Remove the Ignition Coil.
Connect the Ignition Coil harness connector.
NOTE Before continuing, inspect the Ignition Coil for the following condi-
tions. If a problem is found, replace the Ignition Coil. Damage or Carbon
Tracking on the Coil or the spark plug insulator boot.
Install a spark tester on the Ignition Coil.
While cranking the engine observe the spark coming from the spark tester.
NOTE: A crisp blue spark that is able to jump the gap of the spark tester
should be generated.
Is good spark present?

Yes → Go To 5

No → Go To 14
NOTE: Connect the Fuel Injector harness connector before continuing.

5 Turn the ignition off. All

Remove the Spark Plug.
Inspect the Spark Plug for the following conditions.
- Cracks
- Carbon Tracking
- Foreign Material
- Gap size out of specifications
- Loose or broke electrode
NOTE: Lightly tap the bottom of the spark plug on a solid surface. The
electrode in the spark plug should not move.
Were any of the above condition present?

Yes → Replace the Spark Plug.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 6

6 Warning: The fuel system is under a constant pressure (even with the engine All
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Install a fuel pressure gauge.
Start the engine and observe the fuel pressure reading.
NOTE: Fuel pressure specification is 407 KPa +/- 34 KPa (59 psi +/- 5 psi).
Choose a conclusion that best matches your fuel pressure reading.

Within Specification
Go To 7
Below Specification
Go To 12
Above Specification
Replace the fuel filter/pressure regulator.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

118
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0300-MULTIPLE CYLINDER MISFIRE — Continued

TEST ACTION APPLICABILITY

7 NOTE: Before continuing visually and physically inspect the fuel delivery All
system for external leaks or damage. Repair /replace as necessary.
Turn the ignition off.
WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Install special tool #6539 (5/169) or #6631 (3/89) fuel line adapter.
Install the fuel pressure gauge.
Start the engine and allow the fuel system to reach maximum pressure.
Turn the ignition off.
NOTE: Fuel specification is 407 KPa +/- 34 KPa (59 psi +/- 5 psi).
Using special tool #C4390, Hose Clamp Pliers, pinch the rubber fuel line between the
fuel pressure gauge and the engine.
Monitor the fuel pressure gauge for a minimum of 5 minutes.
NOTE: The pressure should not fall below 241 KPa (35 psi)
Does the Upstream gauge fall below the above specification?
Yes → Replace the leaking Fuel Injector(s).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 8

8 Warning: The fuel system is under a constant pressure (even with the engine All
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
CAUTION: After each Fuel Injector actuation, start the engine to clean the
cylinder of fuel. Failure to do so could cause engine damage.
Remove special tool #C4390.
Start the engine and allow the fuel pressure to reach maximum pressure.
Ignition on, engine not running.
Using the DRBIIIt, actuate the Fuel Injector for the cylinder that indicated the
misfire.
Monitor the fuel pressure gauge.
Does the fuel pressure gauge indicate a drop in fuel pressure?
Yes → Go To 9

No → Go To 10
NOTE: Turn the ignition off, remove the Fuel Pressure gauge, and connect
the fuel lines before continuing.

9 Check for any of the following conditions/mechanical problems. All

ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions or leaks.
ENGINE PCV SYSTEM - must flow freely
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
CAM LOBES - must not be worn excessively
CYLINDER LEAKAGE TEST - must be within specifications
VALVE SPRINGS - cannot be weak or broken
Are there any engine mechanical problems?

Yes → Repair as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 16

119
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0300-MULTIPLE CYLINDER MISFIRE — Continued

TEST ACTION APPLICABILITY

10 Turn the ignition off. All
Disconnect the Fuel Injector harness connector.
Ignition on, engine not running.
NOTE: When a Misfire is detected for a particular cylinder, the PCM will
shut down that cylinders Injector Control circuit.
With the DRBIIIt, erase DTCs.
Using a 12-volt test light connected to 12-volts, probe the Injector Control circuit.
With the DRBIIIt, actuate the Fuel Injector.
Does the test light blink/flicker?

Yes → Replace the Fuel Injector.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 11

11 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Check the Injector Control circuit for an open, short to ground, and short to voltage.
Was a problem found with the Injector Control circuit?
Yes → Repair the excessive resistance or short to ground in the Injector
Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 16

12 Turn the ignition off. All

Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Raise vehicle on hoist, and disconnect the fuel pressure line at the fuel pump module.
Install special tool #6539 (5/169) #6631(3/89) fuel line adapter and the fuel pressure
gauge between the fuel supply line and the fuel pump module.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Fuel System test and observe the fuel pressure
gauge.
NOTE: Fuel pressure specification is 407 KPa +/- 34 KPa (59 psi +/- 5 psi).
Is the fuel pressure within specification?

Yes → Repair or replace fuel supply line as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 13

120
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0300-MULTIPLE CYLINDER MISFIRE — Continued

TEST ACTION APPLICABILITY

13 Turn the ignition off. All
Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose,fitting or line, the fuel
system pressure must be released.
Remove the Fuel Pump Module and inspect the Fuel Inlet Strainer.
Is the Fuel Inlet Strainer plugged?

Yes → Replace the Fuel Pump Inlet Strainer.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → NOTE: Before continuing, check the Fuel Pump Module harness
connector terminals for corrosion, damage, or terminal push out.
Ensure the ground circuit is operating properly. Repair as neces-
sary. Replace the Fuel Pump Module.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

14 Disconnect the Ignition Coil harness connector. All

Remove the Fuel Pump Relay or ASD Relay.
Using a 12-volt test light connected to 12-volts, probe the Ignition Coil Control
circuit.
Crank the engine for 5 second while observing the test light.
NOTE: The resistance of the primary Ignition Coil on a 3.7L is 0.6 to 0.9 of an
ohm at 77°F (25°C).
Does the test light brightly blink/flicker?
Yes → Replace the Ignition Coil.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 15

15 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Check the Coil Control circuit for an open, short to ground, and short to voltage.
Was a problem found with the Coil Control circuit?
Yes → Repair the Coil Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 16

16 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

121
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0315-NO CRANK SENSOR LEARNED

When Monitored and Set Condition:

P0315-NO CRANK SENSOR LEARNED

When Monitored: Under closed throttle decel and A/C off. ECT above 75°C (167°F).
Engine start time is greater than 50 seconds.
Set Condition: One of the CKP sensor target windows has more than 2.86% variance from
the reference. One Trip Fault.

POSSIBLE CAUSES
INTERMITTENT CONDITION
TONE WHEEL/PULSE RING INSPECTION
CKP WIRE HARNESS INSPECTION
CRANKSHAFT POSITION SENSOR

TEST ACTION APPLICABILITY

1 NOTE: Check for any TSBs that may apply to this symptom. All
Ignition on, engine not running.
With the DRBIIIt, clear DTCs, PCM battery disconnect to reset the PCM.
Start the engine.
If the MIL has not yet illuminated, test drive the vehicle to try to get the code to reset.
Does the code reset while cranking or during the test drive?
Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Visually inspect the CKP wire harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the CKP wire harness connectors. Look for broken, bent, pushed out,
or corroded terminals.
Make sure the Crankshaft Position Sensor is properly installed and the mounting
bolt(s) is properly torqued to specification.
Were any of the above conditions present?

Yes → Repair as necessary

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 3

122
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0315-NO CRANK SENSOR LEARNED — Continued

TEST ACTION APPLICABILITY

3 Remove the Crankshaft Position Sensor. All
Inspect the Tone Wheel/Flex Plate slots for damage, foreign material, or excessive
movement.
Were any problems found?
Yes → Repair or replace the Tone Wheel/Flex Plate as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

4 If there are no possible causes remaining, view repair. All

Repair
Replace the Crankshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

123
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0335-CRANKSHAFT POSITION SENSOR CIRCUIT

When Monitored and Set Condition:

P0335-CRANKSHAFT POSITION SENSOR CIRCUIT

When Monitored: Engine cranking.
Set Condition: No CKP signal is present during engine cranking, and at least 8 camshaft
position sensor signals have occurred.

POSSIBLE CAUSES
INTERMITTENT CKP SIGNAL
INTERMITTENT CMP SIGNAL
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE
(F855) 5-VOLT SUPPLY CIRCUIT OPEN
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
(K24) CKP SIGNAL CIRCUIT OPEN
(K24) CKP SIGNAL CIRCUIT SHORTED TO VOLTAGE
(K24) CKP SIGNAL CIRCUIT SHORTED GROUND
(K24) CKP SIGNAL CIRCUIT SHORTED TO (F855) 5-VOLT SUPPLY CIRCUIT
(K900) SENSOR GROUND CIRCUIT OPEN
CRANKSHAFT POSITION SENSOR
PCM

TEST ACTION APPLICABILITY

1 Crank the engine. All
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2

No → Go To 14

2 Turn the ignition off. All

Disconnect the CKP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the (F855) 5-volt Supply circuit at the CKP Sensor harness
connector.
Is the voltage between 4.8 and 5.2 volts?
Yes → Go To 3
No → Go To 10

124
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0335-CRANKSHAFT POSITION SENSOR CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Measure the voltage on the (K24) CKP Signal circuit at the CKP Sensor harness All
connector.
Is the voltage between 4.8 and 5.2 volts?

Yes → Go To 4
No → Go To 7

4 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the CKP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (K900) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Measure the resistance between the (K24) CKP Signal circuit and the (F855) 5-volt All
Supply circuit at the CKP Sensor harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the short between the (K24) CKP Signal circuit and the
(F855) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

6 NOTE: Inspect the slots on the flywheel for damage. If a problem is found All
repair as necessary.
If there are no possible causes remaining, view repair.
Repair
Replace the Crankshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Ignition on, engine not running.
Measure the voltage on the (K24) CKP Signal circuit at the CKP Sensor harness
connector.
Is the voltage above 5.3 volts?
Yes → Repair the short to voltage in the (K24) CKP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 8

125
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0335-CRANKSHAFT POSITION SENSOR CIRCUIT — Continued

TEST ACTION APPLICABILITY

8 Turn the ignition off. All
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K24) CKP Signal circuit from the CKP Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 9
No → Repair the open in the (K24) CKP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

9 Measure the resistance between ground and the (K24) CKP Signal circuit at the CKP All
Sensor harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the short to ground in the (K24) CKP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 13

10 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Ignition on, engine not running.
Measure the voltage on the (F855) 5-volt Supply circuit at the CKP Sensor harness
connector.
Is the voltage above 5.5 volts?
Yes → Repair the short to voltage in the (F855) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 11

11 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (F855) 5-volt Supply circuit from the CKP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 12
No → Repair the open in the (F855) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

12 Measure the resistance between ground and the (F855) 5-volt Supply circuit at the All
CKP Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (F855) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 13

126
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0335-CRANKSHAFT POSITION SENSOR CIRCUIT — Continued

TEST ACTION APPLICABILITY

13 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

14 Turn the ignition off. All

With the DRBIIIt lab scope probe and the Miller special tool #6801, backprobe the
(K24) CKP Signal circuit at the CKP harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Wiggle the related wire harness and lightly tap on the Crank Position Sensor.
Observe the lab scope screen.
Look for any pulses generated by the CKP Sensor.
Allow the engine to idle.
Observe the lab scope screen.
Did the CKP Sensor generate any pulses?

Yes → Inspect the related wire harness and replace the Crankshaft
Position Sensor if no wiring problems were found.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 15

15 Turn the ignition off. All

NOTE: An intermittent condition with the CMP Sensor can set the P0335
DTC.
With the DRBIIIt lab scope probe and the Miller special tool #6801, backprobe the
(K44) CMP Signal circuit at the CMP harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Wiggle the related wire harness and lightly tap on the Cam Position Sensor.
Observe the lab scope screen.
Look for any pulses generated by the CMP Sensor.
Allow the engine to idle.
Observe the lab scope screen.
Did the CMP Sensor generate any erratic pulses?
Yes → Inspect the related wire harness and replace the Camshaft
Position Sensor if no wiring problems were found.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Test Complete.

127
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0339-CRANKSHAFT POSITION SENSOR INTERMITTENT

When Monitored and Set Condition:

P0339-CRANKSHAFT POSITION SENSOR INTERMITTENT

When Monitored: While cranking engine and engine running.
Set Condition: When the CKP Sensor failure counter reaches 20. One Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
CKP WIRE HARNESS INSPECTION
(F855) 5-VOLT SUPPLY CIRCUIT OPEN OR SHORTED TO GROUND
TONE WHEEL/PULSE RING INSPECTION
CHECKING CMP SENSOR SIGNAL WITH THE DRBIIIt LAB SCOPE
CRANKSHAFT POSITION SENSOR
(K24) CKP SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K24) CKP SIGNAL CIRCUIT OPEN
(K24) CKP SIGNAL CIRCUIT SHORTED TO GROUND
(K24) CKP SIGNAL CIRCUIT SHORTED TO (F855) 5-VOLT SUPPLY CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

With the DRBIIIt lab scope probe and the Miller special tool #6801, backprobe the
(K24) CKP Signal circuit at the Sensor harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Observe the lab scope screen.
Start the engine.
Observe the lab scope screen.
Are there any irregular or missing signals?

Yes → Go To 3
No → Go To 8

128
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0339-CRANKSHAFT POSITION SENSOR INTERMITTENT — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Visually inspect the related wire harness including the ground circuit. Look for any
chafed, pierced, pinched, or partially broken wires.
Visually inspect the related wire harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Make sure the Crankshaft Position Sensor and the Camshaft Position Sensor are
properly installed and the mounting bolt(s) are tight.
Refer to any TSBs that may apply.
Were any of the above conditions present?

Yes → Repair as necessary

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

4 Disconnect the CKP Sensor connector. All

Ignition on, engine not running.
Measure the voltage on the (F855) 5-volt Supply circuit in the Sensor harness
connector.
Is the voltage between 4.5 and 5.3 volts?
Yes → Go To 5

No → Repair the open or short to ground in the (F855) 5-volt Supply

circuit. Use Miller special tool #8815 when checking for an open
circuit to prevent PCM harness connector terminal damage.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Turn the ignition off. All

Carefully disconnect the Battery Ground cable.
Remove the Crankshaft Position Sensor.
Inspect the Tone Wheel/Flex Plate slots for damage, foreign material, or excessive
movement.
Were any problems found?

Yes → Repair or replace the Tone Wheel/Flex Plate as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

6 NOTE: An intermittent condition in the Cam Position Sensor can cause the All
P0339 to set.
Install the Crankshaft Position Sensor.
With the DRBIIIt lab scope probe and the Miller special tool #6801, backprobe the
(K44) CMP Signal circuit at the Sensor harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Wiggle the related wire harness and lightly tap on the Cam Position Sensor.
Observe the lab scope screen.
Start the engine.
Observe the lab scope screen.
Are there any irregular or missing signals?
Yes → Replace the Cam Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 7

129
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0339-CRANKSHAFT POSITION SENSOR INTERMITTENT — Continued

TEST ACTION APPLICABILITY

7 If there are no possible causes remaining, view repair. All

Repair
Replace the Crankshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

8 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Disconnect the CKP Sensor connector.
Ignition on, engine not running.
Measure the voltage on the (K24) CKP Signal circuit in the Sensor harness connector.
Wiggle the related wire harness while taking this measurement.
Does the voltage ever increase above 5.5 volts?

Yes → Repair the short to voltage in the (K24) CKP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 9

9 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance in the (K24) CKP Signal circuit between the CKP harness
connector and the appropriate terminal of special tool #8815.
Wiggle the wire harness while taking this measurement.
Is the resistance below 1.0 ohm?
Yes → Go To 10
No → Repair the open/high resistance in the (K24) CKP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

10 Measure the resistance between ground and the (K24) CKP Signal circuit at the CKP All
Sensor harness connector.
Wiggle the related wire harness while monitoring the resistance value.
Does the resistance ever go below 100 ohms?
Yes → Repair the short to ground in the (K24) CKP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 11

11 Measure the resistance between the (F855) 5-volt Supply circuit and the (K24) CKP All
Signal circuit at the CKP harness connector.
Wiggle the related wire harness while taking this measurement.
Does the resistance ever go below 5.0 ohms?
Yes → Repair the short between the (F855) 5-volt Supply circuit and the
(K24) CKP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 12

130
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0339-CRANKSHAFT POSITION SENSOR INTERMITTENT — Continued

TEST ACTION APPLICABILITY

12 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, review repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

131
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0340-CAMSHAFT POSITION SENSOR CIRCUIT

When Monitored and Set Condition:

P0340-CAMSHAFT POSITION SENSOR CIRCUIT

When Monitored: Engine cranking/running. Battery voltage greater than 10 volts.
Set Condition: At least 5 seconds or 2.5 engine revolutions have elapsed with crankshaft
position sensor signals present but no camshaft position sensor signal.

POSSIBLE CAUSES
INTERMITTENT CMP SIGNAL
INTERMITTENT CKP SIGNAL
(F856) 5-VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE
(F856) 5-VOLT SUPPLY CIRCUIT OPEN
(F856) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
(K44) CMP SIGNAL CIRCUIT SHORTED TO VOLTAGE
(K44) CMP SIGNAL CIRCUIT OPEN
(K44) CMP SIGNAL CIRCUIT SHORTED TO GROUND
(K44) CMP SIGNAL SHORTED TO THE (F856) 5-VOLT SUPPLY CIRCUIT
(K900) SENSOR GROUND CIRCUIT OPEN
CAMSHAFT POSITION SENSOR
PCM

TEST ACTION APPLICABILITY

1 Crank the engine. All
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2

No → Go To 14

2 Turn the ignition off. All

Disconnect the CMP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the (F856) 5-volt Supply circuit in the CMP Sensor harness
connector.
Is the voltage between 4.5 and 5.2 volts?
Yes → Go To 3
No → Go To 10

132
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0340-CAMSHAFT POSITION SENSOR CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Measure the voltage on the (K44) CMP Signal circuit in the CMP Sensor harness All
connector.
Is the voltage between 4.5 and 5.0 volts?

Yes → Go To 4
No → Go To 7

4 Turn the ignition off. All

Disconnect the C1 and C2 PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the CMP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (K900) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Measure the resistance between the (K44) CMP Signal circuit and the (F856) 5-volt All
Supply circuit in the CMP Sensor harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the short between the (K44) CMP Signal circuit and the
(F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

6 NOTE: Inspect the Camshaft sprocket for damage per the Service Informa- All
tion. If a problem is found repair as necessary.
If there are no possible causes remaining, view repair.
Repair
Replace the Camshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Ignition on, engine not running.
Measure the voltage on the (K44) CMP Signal circuit in the CMP Sensor harness
connector.
Is the voltage above 5.2 volts?
Yes → Repair the short to voltage in the (K44) CMP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 8

133
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0340-CAMSHAFT POSITION SENSOR CIRCUIT — Continued

TEST ACTION APPLICABILITY

8 Turn the ignition off. All
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K44) CMP Signal circuit from the CMP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 9
No → Repair the open in the (K44) CMP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

9 Measure the resistance between ground and the (K44) CMP Signal circuit in the All
CMP Sensor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (K44) CMP Signal circuit
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 13

10 Turn the ignition off. All

Disconnect the C1 and C2 PCM harness connectors.
Ignition on, engine not running.
Measure the voltage on the (F856) 5-volt Supply circuit in the CMP Sensor harness
connector.
Is the voltage above 5.3 volts?
Yes → Repair the short to voltage in the (F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 11

11 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (F856) 5-volt Supply circuit between the CMP Sensor
harness connector and the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 12
No → Repair the open in the (F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

12 Measure the resistance between ground and the (F856) 5-volt Supply circuit in the All
CMP Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 13

134
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0340-CAMSHAFT POSITION SENSOR CIRCUIT — Continued

TEST ACTION APPLICABILITY

13 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

14 Turn the ignition off. All

With the DRBIIIt lab scope probe and the Miller special tool #6801, backprobe the
(K44) CMP Signal circuit in the CMP harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Wiggle the related wire harness and lightly tap on the Cam Position Sensor.
Observe the lab scope screen.
Allow the engine to idle.
Observe the lab scope screen.
Did the CMP Sensor generate any erratic pulses?

Yes → Replace the Camshaft Position Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 15

15 Turn the ignition off. All

With the DRBIIIt lab scope probe and the Miller special tool #6801, back probe the
(K24) CKP Signal circuit in the CKP harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Wiggle the related wire harness and lightly tap the Crank Position Sensor.
Observe the lab scope screen.
Allow the engine to idle.
Observe the lab scope screen.
Did the CKP Sensor generate any erratic pulses?

Yes → Replace the Crankshaft Position Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Test Complete.

135
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0344-CAMSHAFT POSITION SENSOR INTERMITTENT

When Monitored and Set Condition:

P0344-CAMSHAFT POSITION SENSOR INTERMITTENT

When Monitored: While cranking the engine and engine running.
Set Condition: When the failure counter reaches 20. One Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
CMP WIRE HARNESS INSPECTION
(F856) 5-VOLT SUPPLY CIRCUIT OPEN OR SHORTED TO GROUND
TONE WHEEL/PULSE RING INSPECTION
CHECKING CKP SENSOR SIGNAL WITH THE DRBIIIt LAB SCOPE
CAMSHAFT POSITION SENSOR
(K44) CMP SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K44) CMP SIGNAL CIRCUIT OPEN
(K44) CMP SIGNAL CIRCUIT SHORTED TO GROUND
(K44) CMP SIGNAL CIRCUIT SHORTED TO THE (F856) 5-VOLT SUPPLY CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

With the DRBIIIt lab scope probe and the Miller special tool #6801, backprobe the
(K44) CMP Signal circuit in the CMP harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Observe the lab scope screen.
Start the engine.
Observe the lab scope screen.
Are there any irregular or missing signals?

Yes → Go To 3
No → Go To 8

136
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0344-CAMSHAFT POSITION SENSOR INTERMITTENT — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Visually inspect the related wire harness including the ground circuit. Look for any
chafed, pierced, pinched, or partially broken wires.
Visually inspect the related wire harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Make sure the Crankshaft Position Sensor and the Camshaft Position Sensor are
properly installed and the mounting bolt(s) are tight.
Refer to any TSBs that may apply.
Were any of the above conditions present?

Yes → Repair as necessary

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

4 Disconnect the CMP Sensor connector. All

Ignition on, engine not running.
Measure the voltage on the (F856) 5-volt Supply circuit.
Is the voltage between 4.5 and 5.2 volts?
Yes → Go To 5

No → Repair the open or short to ground in the (F856) 5-volt Supply

circuit. Use Miller special tool #8815 when checking for an open
circuit to prevent PCM harness connector terminal damage.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Turn the ignition off. All

Carefully disconnect the Battery Ground cable.
Remove the Camshaft Position Sensor.
Inspect the Tone Wheel/Pulse Ring for damage, foreign material, or excessive
movement.
Were any problems found?

Yes → Repair or replace the Tone Wheel/Pulse Ring as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

6 NOTE: An intermittent condition with the Crank Position Sensor can cause All
the P0344 to set.
Install the CMP Sensor.
With the DRBIIIt lab scope probe and the Miller special tool #6801, backprobe the
(K24) CKP Signal circuit in the CKP harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Wiggle the related wire harness and lightly tap on the Crank Position Sensor.
Observe the lab scope screen.
Start the engine.
Observe the lab scope screen.
Are there any irregular or missing signals?
Yes → Replace the Crank Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 7

137
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0344-CAMSHAFT POSITION SENSOR INTERMITTENT — Continued

TEST ACTION APPLICABILITY

7 If there are no possible causes remaining, view repair. All

Repair
Replace the Camshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

8 Turn the ignition off. All

Disconnect the C1 and C2 PCM harness connectors.
Ignition on, engine not running.
Measure the voltage on the (K44) CMP Signal circuit.
Wiggle the related wire harness while taking this measurement.
Does the voltage ever increase above 5.5 volts?
Yes → Repair the short to voltage in the (K44) CMP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 9

9 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance in the (K44) CMP Signal circuit from the CMP harness
connector to the appropriate terminal of special tool #8815.
Wiggle the related wire harness while taking this measurement.
Is the resistance below 5.0 ohms?

Yes → Go To 10

No → Repair the excessive resistance in the (K44) CMP Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

10 Measure the resistance between ground and the (K44) CMP Signal circuit in the All
CMP Sensor harness connector.
Wiggle the related wire harness while monitoring the resistance value.
Does the resistance ever go below 100 ohms?
Yes → Repair the short to ground in the (K44) CMP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 11

11 Measure the resistance between the (F856) 5-volt Supply circuit and the (K44) CMP All
Signal circuit in the CMP harness connector.
Wiggle the related wire harness while taking this measurement.
Does the resistance ever go below 5.0 ohms?

Yes → Repair the short between the (F856) 5-volt Supply circuit and the
(K44) CMP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 12

138
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0344-CAMSHAFT POSITION SENSOR INTERMITTENT — Continued

TEST ACTION APPLICABILITY

12 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, review repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

139
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom List:
P0420-CATALYST 1/1 EFFICIENCY
P0430-CATALYST 2/1 EFFICIENCY

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0420-CATALYST 1/1 EFFI-
CIENCY.

When Monitored and Set Condition:

P0420-CATALYST 1/1 EFFICIENCY

When Monitored: After engine warm up to 70°C (158°F), 180 seconds of open throttle
operation, at a speed greater than 18 mph and less than 55 mph, with the engine at
1200-1700 rpm and MAP vacuum between 15.0 and 21.0 inches of mercury (Hg).
Set Condition: As catalyst efficiency deteriorates, the switch rate of the downstream O2
sensor approaches that of the upstream O2 sensor. If at any point during the test the
switch ratio reaches a predetermined value a counter is incremented by one.

P0430-CATALYST 2/1 EFFICIENCY

When Monitored: After engine warm up to 147 deg. F, 180 seconds of open throttle
operation, at a speed greater than 20 mph, with the engine at 1200-1700 rpm and MAP
vacuum between 15.0 and 21.0 inches of mercury (Hg).
Set Condition: As catalyst efficiency deteriorates, the switch rate of the downstream O2
sensor approaches that of the upstream O2 sensor. If at any point during the test the
switch ratio reaches a predetermined value a counter is incremented by one. Three good
trips to turn off the MIL.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
VISUALLY INSPECT CATALYTIC CONVERTER
EXHAUST LEAK
ENGINE MECHANICAL CONDITION
AGING O2 SENSOR
CATALYTIC CONVERTER

140
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0420-CATALYST 1/1 EFFICIENCY — Continued

TEST ACTION APPLICABILITY

1 NOTE: A new rear O2 Sensor along with an aging front O2 Sensor may cause All
the DTC to set. Review the repair history of the vehicle before continuing.
NOTE: If a O2 Sensor DTC(s) set along with the Catalytic Converter
Efficiency DTC diagnose the O2 Sensor DTC(s) before continuing.
NOTE: Check for contaminants that may have damaged the O2 Sensor and
Catalytic Converter: contaminated fuel, unapproved silicone, oil and cool-
ant, repair necessary.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Inspect the Catalytic Converter for the following damage. All

Damage Catalytic Converter, dent and holes.
Severe discoloration caused by overheating the Catalytic Converter.
Catalytic Converter broke internally.
Leaking Catalytic Converter.
Were any problems found?
Yes → Replace the Catalytic Converter. Repair the condition that may
have caused the failure.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

3 Start the engine. All

Inspect the exhaust for leak between the engine and the O2 Sensor.
Inspect the exhaust for leaks between the engine and the appropriate rear O2 Sensor.
Are there any exhaust leaks?

Yes → Repair or replace the leaking exhaust parts as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

4 Check the exhaust for excessive smoke caused by an internal problem in the engine. All
Is an engine mechanical condition present?

Yes → Repair the engine mechanical condition as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 A new rear O2 Sensor along with an aging front O2 Sensor may cause the DTC to set. All
Review the vehicles repair history.
Has the rear O2 Sensor been replace without replacing the front O2 Sensor?

Yes → Replace the Front O2 Sensor as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 6

6 If there are no possible cause remaining, view repair. All

Repair
Replace the Catalytic Converter.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

141
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
Symptom:
P0440-GENERAL EVAP SYSTEM FAILURE

When Monitored and Set Condition:

P0440-GENERAL EVAP SYSTEM FAILURE

When Monitored: Engine Running. Fuel Level greater than 12%. Ambient Temperature
between 4°C and 32°C (39°F and 89°F)
Set Condition: The PCM does not see the NVLD swtich close during the medium/large
leak test. The PCM then will increase the vacuum supply to the EVAP system by
increasing flow through the EVAP Purge valve. If the switch does not close with an
increase in vacuum an error is detected. Two Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
VEHICLE HISTORY AND SERVICE BULLETIN INVESTIGATION
VISUAL AND PHYSICAL INSPECTION
EVAP PURGE SOLENOID VACUUM SUPPLY INSPECTION
EVAP PURGE SOLENOID
NVLD SWITCH OPERATION
GROUND CIRCUIT OPEN
NVLD ASSEMBLY
NVLD SWITCH SIGNAL CIRCUIT OPEN
EVAPORATIVE EMISSION LEAK DETECTION
PCM

TEST ACTION APPLICABILITY

1 Start by reading PCM DTC(s) and record the related Freeze Frame data in any All
DTC(s) are present.
Check the vehicle repair history.
If the vehicle has a repair history that pertains to the customer’s current complaint,
review the repair.
Inspect the vehicle for any aftermarket accessories that may have been installed
incorrectly.
Check for any service bulletin(s) related to the customer’s complaint or DTC(s).
If a service bulletin applies, follow the instructions per service bulletin.
Did the service bulletin repair the customer’s complaint?

Yes → Testing Complete.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 2

142
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0440-GENERAL EVAP SYSTEM FAILURE — Continued

TEST ACTION APPLICABILITY

2 NOTE: If any of the following DTCs are set (P0443, P0452, P0453, P0498 or All
P0499) diagnose them first before continuing with P0440.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 3

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

3 Perform a visual and physical inspection of the entire Evaporative Emission system. All
Check for the following conditions:
- Hoses disconnected or left off
- Holes or cracks
- Loose seal points
- Evidence of damaged components
- Incorrect routing of hoses and tubes
- Fuel Cap left off or bad gasket seal
Were any of the above conditions found?
Yes → Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Turn the ignition off. All

Carefully inspect the Evap Purge Solenoid vacuum supply hose for proper routing.
Check for a pinched or plugged hose from the throttle body to the Purge Solenoid.
Make sure the vacuum port at the throttle body or intake manifold is free from any
blockage.
Were any problems found?
Yes → Repair the vacuum supply, hose/tube as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

143
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0440-GENERAL EVAP SYSTEM FAILURE — Continued

TEST ACTION APPLICABILITY

5 To continue testing you will need Miller Tool #8404 Evaporative Emission Leak All
Detector (EELD).
WARNING: Keep lit cigarettes, sparks, flames, and other ignition sources
away from the test area to prevent the ignition of explosive gases. Keep the
test area well ventilated.
Connect the red power lead of EELD to the battery positive terminal and the black
ground lead to battery negative terminal.
Disconnect the vacuum hoses at he Evap Purge Solenoid.
Connect the SMOKE supply tip (black hose) to the service port (if equipped) or to the
#8404-ADP adapter.
Set the smoke/air control switch to SMOKE.
Press the remote smoke/air start button.
NOTE: Below is an optional method of checking the purge valve for leaks if
the EELD is unavailable.
Turn the ignition off.
Disconnect the vacuum supply hoses from the EVAP Purge Solenoid.
Using a hand vacuum pump, apply 10 in Hg to the 9CAN9 side of the EVAP Purge
Solenoid.
Observe the vacuum gauge for at least 15 seconds.
With the DRBIIIt, actuate the Evap Purge Solenoid.
NOTE: If the Evap Purge Solenoid does not hold a vacuum, it will need to be
replaced.
Is smoke visible from the Evap Purge Solenoid?

Yes → Replace the Evap Purge Solenoid.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

6 Connect the previously disconnected vacuum hose. All

Start the engine.
Allow the engine to idle.
Using the DRBIIIt, perform the NVLD FORCED MONITOR TEST.
Monitor the NVLD Switch state.
NOTE: As the test runs, the NVLD Switch should go from an OPEN state to
a CLOSED state and then return to OPEN when the test is complete.
Did the NVLD Switch operate as described above?

Yes → Test Complete.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 7

144
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0440-GENERAL EVAP SYSTEM FAILURE — Continued

TEST ACTION APPLICABILITY

7 To continue testing you will need Miller Tool #8404 Evaporative Emission Leak All
Detector (EELD).
WARNING: Keep lit cigarettes, sparks, flames, and other ignition sources
away from the test area to prevent the ignition of explosive gases. Keep the
test area well ventilated.
NOTE: The fuel tank should have between 20% and 80% of fuel tank capacity
to properly test the Evap system.
Connect the red power lead of EELD to the battery positive terminal and the black
ground lead to battery negative terminal.
NOTE: See Charts and Graph support material EELD Calibration Setup for
an example.
Block the vent hose of the EVAP Canister.
Connect shop air to the EELD.
Set the smoke/air control switch to AIR.
Insert the tester’s AIR supply tip (clear hose) into the .040 orifice on the tester’s
control panel.
Press the remote smoke/air start button.
Position the red flag on the air flow meter so it is aligned with the indicator ball.
When the calibration is complete, release the remote button. The EELD flow meter
is now calibrated in liters per minute.
Install the service port adapter #8404-14 on the vehicle’s service port (if equipped) or
install the #8404-ADP into the filter line.
Connect the Air supply hose from the EELD to the service port (if equipped) or to the
#8404-ADP adapter.
Press the remote button to activate AIR flow.
NOTE: Larger volume fuel tanks, lower fuel levels or if the vehicle is
equipped with a Flow Management Valve, this may indicate high flow and
will require 4 to 5 minutes to fill.
Compare the flow meter indicator ball reading to the red flag.
ABOVE the red flag indicates a leak present.
BELOW the red flag indicates a sealed system.
Is the indicator ball above the red flag?

Yes → Go To 8
No → Go To 9

145
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0440-GENERAL EVAP SYSTEM FAILURE — Continued

TEST ACTION APPLICABILITY

8 NOTE: A thorough visual inspection of the Evap system hoses, tubes, and All
connections may save time in your diagnosis. Look for any physical damage
or signs of wetness at connections. The strong smell of fuel vapors may aid
diagnosis also.
To continue testing, you will need Miller Tool #8404 Evaporative Emissions Leak
Detector (EELD).
Remove the Air supply hose from the service port or the #8404-ADP adapter.
Connect the SMOKE supply tip (black hose) to the service port (if equipped) or to the
#8404-ADP adapter.
Set the smoke/air control switch to SMOKE.
NOTE: The flow meter indicator ball will not move at this point.
Press the remote smoke/air start button.
NOTE: Make sure that smoke has filled the EVAP system by continuing to
press the remote smoke/air start button, remove the vehicle fuel cap, and
wait for the smoke to exit. Once smoke is indicated reinstall the fuel cap.
NOTE: For optimal performance, introduce smoke into the system for an
additional 60 seconds; continue introducing smoke at 15 second intervals,
as necessary.
While still holding the remote smoke/air start button, use the white light (#8404-
CLL) to follow the EVAP system path, and look for the source of the leak indicated by
exiting smoke.
If a leak is concealed from view (i.e., top of fuel tank), release the remote smoke/air
start button, and use the ultraviolet (UV) black light #8404-UVL and the yellow
goggles 8404-20 to look for residual traces of dye that are left behind by the smoke.
The exiting smoke deposits a residual fluid that is either bright green or bright
yellow in color when viewed with a UV light.
NOTE: The EVAP System is divided into three zones. Possible leaking areas
can be from any of the three Zones.
ZONE 1.
- Fuel tank valves (control valve and inlet check valve).
- Cracked, cut, warped, or missing primary fuel filler cap to fuel filler tube seal.
- Out of round fuel filler tube.
- Fuel filler tube to fuel filler hose connection.
- Fuel filler hose to tank connection.
- Fuel tank shell.
- Fuel pump module attachment.
- Gas cap loose or seal damaged.
- Gas cap internal valve.
- Damaged or disconnected EVAP system components.
ZONE 2.
- EVAP hoses loose or disconnected.
- Damaged or disconnected EVAP system components.
- Canister seals/hoses leaking.
- Canister housing.
- NVLD Assembly.
ZONE 3.
- EVAP Purge valve.
- EVAP hoses loose, cracked, or disconnected.
NOTE: Carefully inspect the vent side of the EVAP Canister. Due to the
filtering system in the canister the smoke or dye may or may not be visible.
Introducing smoke into the filtered side of the canister may assist in
locating the leak.
Was a leak found?
Yes → Repair or replace the leaking component as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 12

146
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0440-GENERAL EVAP SYSTEM FAILURE — Continued

TEST ACTION APPLICABILITY

9 Turn the ignition off. All
Disconnect the NVLD electrical harness connector.
Check connectors - Clean/repair as necessary.
Connect a jumper wire between the NVLD Switch Signal circuit and the Ground
circuit in the NVLD electrical harness connector.
Monitor the NVLD Switch state on the DRBIIIt.
Does the Switch change from OPEN to CLOSED.

Yes → Replace the NVLD Assembly.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 10

10 Turn the ignition off. All

Disconnect the NVLD electrical harness connector.
Measure the resistance between the Ground circuit and ground.
Is the resistance below 5.0 ohms?
Yes → Go To 11
No → Repair the open in the Ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

11 Turn the ignition off. All

Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the NVLD Switch Signal circuit from the NVLD electrical
harness connector to the appropriate terminal of the special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 12
No → Repair the open in the NVLD Switch Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

12 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

146A
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
Symptom:
P0441-EVAP PURGE SYSTEM PERFORMANCE

When Monitored and Set Condition:

P0441-EVAP PURGE SYSTEM PERFORMANCE

When Monitored: Cold start test. Engine Running. Small Leak Test Passed.
Set Condition: The PCM activates the EVAP Purge solenoid gradually increases to
maximum flow. During flow, the PCM looks for the NVLD switch to close. If the PCM does
not see the NVLD switch close at maximum flow an error is detected. Two Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
NVLD SWITCH OPERATION
VEHICLE HISTORY AND SERVICE BULLETIN INVESTIGATION
CHECKING EVAP PURGE SOLENOID FUNCTIONALITY
EVAP PURGE SOLENOID VACUUM SUPPLY
VERIFY NVLD OPERATION

TEST ACTION APPLICABILITY

1 Start by reading PCM DTC(s) and record the related Freeze Frame data in any All
DTC(s) are present.
Check the vehicle repair history.
If the vehicle has a repair history that pertains to the customer’s current complaint,
review the repair.
Inspect the vehicle for any aftermarket accessories that may have been installed
incorrectly.
Check for any service bulletin(s) related to the customer’s complaint or DTC(s).
If a service bulletin applies, follow the instructions per service bulletin.
Did the service bulletin repair the customer’s complaint?

Yes → Testing Complete.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 2

2 NOTE: If any of the following DTCs are set (P0443, P0452, P0453, P0498 or All
P0499) diagnose them first before continuing with P0441.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 3

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

147
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0441-EVAP PURGE SYSTEM PERFORMANCE — Continued

TEST ACTION APPLICABILITY

3 NOTE: After disconnecting the Evap Purge vacuum connections, inspect All
the lines and solenoid for any signs of contamination or foreign materials.
Using a hand vacuum pump, apply 10 in Hg to 9CAN9 side of the EVAP Purge
Solenoid.
Ignition on, engine not running.
Observe the vacuum gauge.
With the DRBIIIt, actuate the EVAP Purge Solenoid .
Does the vacuum drop when the solenoid is actuated?

Yes → Go To 4
No → Replace the Evap Purge Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Turn the ignition off. All

Carefully inspect the Evap Purge Solenoid vacuum supply hose for proper routing.
Check for a pinched or plugged hose from the throttle body to the Purge Solenoid.
Inspect the vacuum port at the throttle body for any damage or plugging.
Were any problems found?
Yes → Repair the vacuum supply hose/tube as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 Connect the previously disconnected vacuum hoses. All

Start the engine.
Allow the engine to idle.
Using the scan tool, perform the NVLD FORCED MONITOR TEST.
Monitor the NVLD Switch state.
NOTE: As the test runs, the NVLD Switch should go from an OPEN to a
CLOSED state and then return to OPEN when the test is complete. This may
take up to 10 minutes.
Did the NVLD Switch operate as described above?

Yes → Test complete.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

6 Perform the NVLD FORCED MONITOR TEST for the second time. All
While the NVLD FORCED MONITOR TEST is running, open/remove the gas cap.
Did the NVLD Switch go from OPEN to CLOSED?

Yes → Replace the NVLD Assembly.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No.
Test Complete.

148
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
Symptom List:
P0442-EVAP SYSTEM MEDIUM LEAK
P0455-EVAP SYSTEM LARGE LEAK

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0442-EVAP SYSTEM MEDIUM
LEAK.

When Monitored and Set Condition:

P0442-EVAP SYSTEM MEDIUM LEAK

When Monitored: Engine Running. Cold start test. Fuel Level greater than 12%. Ambient
Temperature between 4°C and 32°C (39°F and 89°F) Close Loop fuel system. Test runs
when small leak test is maturing.
Set Condition: The PCM activates the EVAP Purge Solenoid to pull the EVAP system into
a vacuum to close the NVLD swtich. Once the NVLD swtich is closed, the PCM turns the
EVAP Pugre solenoid off to seal the EVAP system. If the NVLD switch reopens before the
calibrated amount of time for a Medium leak an error is detected. Two Trip Fault.

P0455-EVAP SYSTEM LARGE LEAK

When Monitored: Engine Running. Cold start test. Fuel Level greater than 12%. Ambient
Temperature between 4°C and 32°C (39°F and 89°F) Close Loop fuel system. Test runs
when small leak test is maturing.
Set Condition: The PCM activates the EVAP Purge Solenoid to pull the EVAP system into
a vacuum to close the NVLD swtich. Once the NVLD switch is closed, the PCM turns the
EVAP Purge solenoid off to seal the EVAP system. If the NVLD switch reopens before the
calibrated amount of time for a Large leak an error is detected. Two Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
LEAK AT GAS CAP
VEHICLE HISTORY AND SERVICE BULLETIN INVESTIGATION
VISUAL AND PHYSICAL INSPECTION
VERIFY EVAPORATIVE EMISSION SYSTEM LEAK
EVAP PURGE SOLENOID OPERATION
EVAPORATIVE EMISSION LEAK DETECTION
GAS CAP
NVLD

148A
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0442-EVAP SYSTEM MEDIUM LEAK — Continued

TEST ACTION APPLICABILITY

1 Start by reading PCM DTC(s) and record the related Freeze Frame data in any All
DTC(s) are present.
Check the vehicle repair history.
If the vehicle has a repair history that pertains to the customer’s current complaint,
review the repair.
Inspect the vehicle for any aftermarket accessories that may have been installed
incorrectly.
Check for any service bulletin(s) related to the customer’s complaint or DTC(s).
If a service bulletin applies, follow the instructions per service bulletin.
Did the service bulletin repair the customer’s complaint?

Yes → Testing Complete.

Perform POWERTRAIN VERIFICATION TEST VER - 6.

No → Go To 2

2 Check for any related TSBs before continuing. All

NOTE: Since a hot vehicle can conceal a leak, it is best to perform this test
at room temperature.
NOTE: A loose gas cap could have caused this DTC to set. Make sure gas cap
is tight and in good condition. Make sure the gas cap meets OEM specifica-
tions.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 3

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 6.

3 Perform a visual and physical inspection of the entire Evaporative Emission system. All
Check for the follow conditions:
- Holes or cracks
- Loose seal points
- Evidence of damaged components
- Incorrect routing of hoses and tubes
- Fuel Cap gasket seal
Were any of the above conditions found?
Yes → Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

No → Go To 4

148B
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0442-EVAP SYSTEM MEDIUM LEAK — Continued

TEST ACTION APPLICABILITY

4 To continue testing you will need Miller Tool #8404 Evaporative Emission Leak All
Detector (EELD).
WARNING: Keep lit cigarettes, sparks, flames, and other ignition sources
away from the test area to prevent the ignition of explosive gases. Keep the
test area well ventilated.
NOTE: The fuel tank should have between 20% and 80% of fuel tank capacity
to properly test the Evap system.
Connect the red power lead of the EELD to the battery positive terminal and the
black ground lead to battery negative terminal.
NOTE: See Charts and Graph support material EELD Calibration Setup for
an example.
Block the vent hose of the EVAP Canister.
Connect shop air to the EELD.
Set the smoke/air control switch to AIR.
Insert the tester’s AIR supply tip (clear hose) into the appropriate calibration orifice
on the tester’s control panel (based on DTC leak size).
Press the remote smoke/air start button.
Position the red flag on the air flow meter so it is aligned with the indicator ball.
When the calibration is complete, release the remote button. The EELD flow meter
is now calibrated in liters per minute to the size leak indicated by the DTC set in the
PCM.
Install the service port adapter #8404-14 on the vehicle’s service port (if equipped) or
install #8404-ADP service adaptor in the filter line.
Connect the Air supply hose from the EELD to the service port (if equipped) or
#8404-ADP in the filter line.
Press the remote button to activate AIR flow.
NOTE: Larger volume fuel tanks, lower fuel levels or if the vehicle is
equipped with a Flow Management Valve may indicate high flow and will
require 4 to 5 minutes to fill
Compare the flow meter indicator ball reading to the red flag.
ABOVE the red flag indicates a leak present.
BELOW the red flag indicates a sealed system.
Is the indicator ball above the red flag?

Yes → Go To 5
No → Refer to the Freeze Frame data recorded in Step 1. If the data
indicates that the vehicle was in motion when the DTC was set,
verify that all hoses are properly connected. Test Complete.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

148C
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0442-EVAP SYSTEM MEDIUM LEAK — Continued

TEST ACTION APPLICABILITY

5 NOTE: A thorough visual inspection of the Evap system hoses, tubes, and All
connections may save time in your diagnosis. Look for any physical damage
or signs of wetness at connections. The strong smell of fuel vapors may aid
diagnosis also.
To continue testing, you will need Miller Tool #8404 Evaporative Emissions Leak
Detector (EELD).
Remove the Air supply hose from the service port or the #8404-ADP adapter.
Connect the SMOKE supply tip (black hose) to the service port (if equipped) or to the
#8404-ADP adapter.
Set the smoke/air control switch to SMOKE.
NOTE: The flow meter indicator ball will not move at this point.
Press the remote smoke/air start button.
NOTE: Make sure that smoke has filled the EVAP system by continuing to
press the remote smoke/air start button, remove the vehicle fuel cap, and
wait for the smoke to exit. Once smoke is indicated reinstall the fuel cap.
NOTE: For optimal performance, introduce smoke into the system for an
additional 60 seconds; continue introducing smoke at 15 second intervals,
as necessary.
While still holding the remote smoke/air start button, use the white light (#8404-
CLL) to follow the EVAP system path, and look for the source of the leak indicated by
exiting smoke.
If a leak is concealed from view (i.e., top of fuel tank), release the remote smoke/air
start button, and use the ultraviolet (UV) black light #8404-UVL and the yellow
goggles 8404-20 to look for residual traces of dye that are left behind by the smoke.
The exiting smoke deposits a residual fluid that is either bright green or bright
yellow in color when viewed with a UV light.
NOTE: The EVAP System is divided into three zones. Possible leaking areas
can be from any of the three Zones.
ZONE 1.
- Fuel tank valves (control valve and inlet check valve).
- Cracked, cut, warped, or missing primary fuel filler cap to fuel filler tube seal.
- Out of round fuel filler tube.
- Fuel filler tube to fuel filler hose connection.
- Fuel filler hose to tank connection.
- Fuel tank shell.
- Fuel pump module attachment.
- Gas cap loose or seal damaged.
- Gas cap internal valve.
- Damaged or disconnected EVAP system components.
ZONE 2.
- EVAP hoses loose or disconnected.
- Damaged or disconnected EVAP system components.
- Canister seals/hoses leaking.
- Canister housing.
- NVLD Assembly.
ZONE 3.
- EVAP Purge valve.
- EVAP hoses loose, cracked, or disconnected.
NOTE: Carefully inspect the vent side of the EVAP Canister. Due to the
filtering system in the canister the smoke or dye may or may not be visible.
Introducing smoke into the filtered side of the canister may assist in
locating the leak.
Was a leak found?
Yes → Go To 6

No → Go To 7

148D
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0442-EVAP SYSTEM MEDIUM LEAK — Continued

TEST ACTION APPLICABILITY

6 Remove the SMOKE supply tip (black hose) from the Service port (if equipped) or to All
the #8404-ADP adapter.
Install gas cap adapter, Miller Tool #8382 (1/4 turn cap) or #6922 (screw cap) and
#8399 (secondary seal depressor) and repeat test 5.
Was a leak at the gas cap adapter?

Yes → Replace the fuel filler tube assembly.

Perform POWERTRAIN VERIFICATION TEST VER - 6.

No → Replace the gas cap.

Perform POWERTRAIN VERIFICATION TEST VER - 6.

7 To continue testing you will need Miller Tool #8404 Evaporative Emission Leak All
Detector (EELD).
WARNING: Keep lit cigarettes, sparks, flames, and other ignition sources
away from the test area to prevent the ignition of explosive gases. Keep the
test area well ventilated.
Connect the red power lead of EELD to the battery positive terminal and the black
ground lead to battery negative terminal.
Disconnect the vacuum hoses at he Evap Purge Solenoid.
Connect the SMOKE supply tip (black hose) to the service port (if equipped) or to the
#8404-ADP adapter.
Set the smoke/air control switch to SMOKE.
Press the remote smoke/air start button.
NOTE: Below is an optional method of checking the purge valve for leaks if
the EELD is unavailable.
Turn the ignition off.
Disconnect the vacuum supply hoses from the EVAP Purge Solenoid.
Using a hand vacuum pump, apply 10 in Hg to the 9CAN9 side of the EVAP Purge
Solenoid.
Observe the vacuum gauge for at least 15 seconds.
With the DRBIIIt, actuate the Evap Purge Solenoid.
NOTE: If the Evap Purge Solenoid does not hold a vacuum, it will need to be
replaced.
Is smoke visible from the Evap Purge Solenoid?
Yes → Replace the Evap Purge Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 6.
No → Replace the NVLD Assembly.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

148E
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
Symptom:
P0443-EVAP PURGE SOLENOID CIRCUIT

When Monitored and Set Condition:

P0443-EVAP PURGE SOLENOID CIRCUIT

When Monitored: The ignition on or engine running. Battery voltage greater than 10
volts.
Set Condition: The PCM will set a trouble code if the actual state of the solenoid does not
match the intended state.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
VEHICLE HISTORY AND SERVICE BULLETIN INVESTIGATION
EVAP PURGE SOLENOID
EVAP PURGE SOL CONTROL CIRCUIT OPEN
EVAP PURGE SOL CONTROL CIRCUIT SHORTED TO GROUND
EVAP PURGE SOL SIGNAL CIRCUIT OPEN
EVAP PURGE SOL SIGNAL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Start by reading PCM DTC(s) and record the related Freeze Frame data in any All
DTC(s) are present.
Check the vehicle repair history.
If the vehicle has a repair history that pertains to the customer’s current complaint,
review the repair.
Inspect the vehicle for any aftermarket accessories that may have been installed
incorrectly.
Check for any service bulletin(s) related to the customer’s complaint or DTC(s).
If a service bulletin applies, follow the instructions per service bulletin.
Did the service bulletin repair the customer’s complaint?

Yes → Testing Complete.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 2

2 Ignition on, engine not running. All

With the DRBIIIt, read DTCs.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 3

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

149
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0443-EVAP PURGE SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the EVAP Purge Solenoid harness connector.
Ignition on, engine not running.
Using a 12-volt test light, jump across the Evap Purge Sol Control circuit and Evap
Purge Sol Signal circuits in the EVAP Purge Solenoid harness connector.
With the DRBIIIt, actuate the EVAP Purge Solenoid.
Does the test light flash on and off?

Yes → Replace the EVAP Purge Solenoid.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Turn the ignition off. All

Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the Evap Purge Sol Control circuit from the Evap Purge
Solenoid harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 5
No → Repair the open in the Evap Purge Sol Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Measure the resistance between ground and the Evap Purge Sol Control circuit at the All
Evap Purge Solenoid harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the short to ground in the Evap Purge Sol Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

6 Measure the resistance of the Evap Purge Sol Signal circuit from the Evap Purge All
Solenoid harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 7

No → Repair the open in the Evap Purge Sol Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 Measure the resistance between ground and the Evap Purge Sol Signal circuit at the All
Evap Purge Solenoid harness connector.
Is the resistance below 5.0 ohms?

Yes → Repair the short to ground in the Evap Purge Sol Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 8

150
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0443-EVAP PURGE SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

8 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

151
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
Symptom:
P0452-NVLD PRESSURE SWITCH STUCK CLOSED

When Monitored and Set Condition:

P0452-NVLD PRESSURE SWITCH STUCK CLOSED

When Monitored: Immediately after the engine has been started.
Set Condition: The PCM activates the NLVD Solenoid. If PCM does not see NVLD switch
open and error is detected. One Trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
VEHICLE HISTORY AND SERVICE BULLETIN INVESTIGATION
EVAP PURGE SOLENOID LEAKS/STUCK OPEN
EVAP PURGE SOL CONTROL CIRCUIT SHORTED TO GROUND
NVLD SWITCH OPERATION
NVLD ASSEMBLY
NVLD SWITCH SIGNAL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Start by reading PCM DTC(s) and record the related Freeze Frame data in any All
DTC(s) are present.
Check the vehicle repair history.
If the vehicle has a repair history that pertains to the customer’s current complaint,
review the repair.
Inspect the vehicle for any aftermarket accessories that may have been installed
incorrectly.
Check for any service bulletin(s) related to the customer’s complaint or DTC(s).
If a service bulletin applies, follow the instructions per service bulletin.
Did the service bulletin repair the customer’s complaint?

Yes → Testing Complete.

Perform POWERTRAIN VERIFICATION TEST VER - 6.

No → Go To 2

2 Check for any related TSBs before continuing. All

Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 3

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 6.

152
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0452-NVLD PRESSURE SWITCH STUCK CLOSED — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the EVAP Purge Solenoid harness connector.
Ignition on, engine not running.
Using a 12-volt test light, jump across the EVAP Purge Solenoid harness connector.
With the DRBIIIt, actuate the EVAP Purge Solenoid.
Does the test light flash on and off?

Yes → Go To 4

No → Go To 8

4 Turn the ignition off. All

Connect the Evap Purge Solenoid harness connector.
Disconnect the vacuum hoses at the Evap Purge Solenoid.
NOTE: After disconnecting the Evap Purge Solenoid vacuum connections,
inspect the lines and solenoid for any signs of contamination from the EVAP
Canister. This may indicate a faulty check valve. Replace/repair as neces-
sary.
Using a hand vacuum pump, apply 10 in Hg to the 9CAN9 of the EVAP Purge
Solenoid.
NOTE: Monitor the vacuum gauge for at least 15 seconds.
Does the EVAP Purge Solenoid hold vacuum?
Yes → Go To 5
No → Replace the Evap Purge Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

5 Ignition on, engine not running. All

Using the DRBIIIt, monitor the NVLD Switch State with the vacuum pump still
installed and holding vacuum.
Does the DRBIIIt display the NVLD state OPEN?
Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 6.
No → Go To 6

NOTE: Remove the vacuum pump and connect the vacuum hose before
continuing.

6 Disconnect the NVLD electrical connector. All

Does the Switch change from CLOSED to OPEN?

Yes → Replace the NVLD Assembly.

Perform POWERTRAIN VERIFICATION TEST VER - 6.

No → Go To 7

7 Turn the ignition off. All

Disconnect the C3 PCM harness connector.
Measure the resistance between ground and the NVLD Switch Signal circuit in the
NVLD Assembly harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the short to ground in the NVLD Switch Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

No → Go To 9

153
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0452-NVLD PRESSURE SWITCH STUCK CLOSED — Continued

TEST ACTION APPLICABILITY

8 Turn the ignition off. All
Disconnect the C3 PCM harness connector.
Measure the resistance between ground and the Evap Purge Sol Control circuit at the
EVAP Purge Solenoid harness connector.
Is the resistance below 5.0 ohms?

Yes → Repair the short to ground in the Evap Purge Sol Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

No → Go To 9

9 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

154
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
Symptom:
P0453-NVLD PRESSURE SWITCH STUCK OPEN

When Monitored and Set Condition:

P0453-NVLD PRESSURE SWITCH STUCK OPEN

When Monitored: Engine running.
Set Condition: If the PCM does not see the NVLD swtich close during test an error is
detected. One Trip Fault.

POSSIBLE CAUSES
NVLD SWITCH OPERATION
VEHICLE HISTORY AND SERVICE BULLETIN INVESTIGATION
NVLD ASSEMBLY
NVLD SWITCH SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
NVLD SWITCH SIGNAL CIRCUIT OPEN
NVLD SWITCH SIGNAL CIRCUIT SHORTED TO THE SOLENOID CONTROL CIRCUIT
GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Start by reading PCM DTC(s) and record the related Freeze Frame data in any All
DTC(s) are present.
Check the vehicle repair history.
If the vehicle has a repair history that pertains to the customer’s current complaint,
review the repair.
Inspect the vehicle for any aftermarket accessories that may have been installed
incorrectly.
Check for any service bulletin(s) related to the customer’s complaint or DTC(s).
If a service bulletin applies, follow the instructions per service bulletin.
Did the service bulletin repair the customer’s complaint?

Yes → Testing Complete.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 2

155
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0453-NVLD PRESSURE SWITCH STUCK OPEN — Continued

TEST ACTION APPLICABILITY

2 Check for any related TSBs before continuing. All
Start the engine.
Allow the engine to idle.
Using the DRBIIIt, perform the NVLD FORCED MONITOR TEST.
Monitor the NVLD Switch state.
NOTE: As the test runs, the NVLD Switch should go from an OPEN state to
a CLOSED state and then return to OPEN when the test is complete.
Did the NVLD Switch operate as described above?

Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

3 Turn the ignition off. All

Disconnect the NVLD electrical harness connector.
Ignition on, engine not running.
Monitor the NVLD Switch state on the DRBIIIt.
Connect a jumper wire between the NVLD Switch Signal circuit and the Ground
circuit in the NVLD harness connector.
Does the Switch change from OPEN to CLOSED?
Yes → Replace the NVLD Assembly.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4
NOTE: Remove the jumper wire before continuing.

4 Turn the ignition off. All

Disconnect the C3 PCM harness connector.
Ignition on, engine not running.
Measure the voltage on the NVLD Switch Signal circuit in the NVLD electrical
harness connector.
Is the voltage above 5.3 volts?
Yes → Repair short to voltage in the NVLD Switch Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the NVLD Switch Signal circuit from the NVLD electrical
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6

No → Repair the open in the NVLD Switch Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

156
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0453-NVLD PRESSURE SWITCH STUCK OPEN — Continued

TEST ACTION APPLICABILITY

6 Measure the resistance between the NVLD Switch Signal circuit and the NVLD Sol All
Control circuit in the NVLD electrical harness connector.
Is the resistance below 5.0 ohms?

Yes → Repair the short between the NVLD Switch Signal circuit and the
NVLD Solenoid Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 7

7 Measure the resistance between the Ground circuit and ground. All
Is the resistance below 5.0 ohms?

Yes → Go To 8
No → Repair the open in the Ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

8 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

157
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004

Symptom:
P0456-EVAP SYSTEM SMALL LEAK

When Monitored and Set Condition:

P0456-EVAP SYSTEM SMALL LEAK

When Monitored: Ignition off. Fuel Level less than 88%. Ambient Temperature between
4°C to 43°C (39°F to 109°F)
Set Condition: Due to temperature changes a vacuum is created in the fuel tank and
EVAP system. With the EVAP system sealed, the PCM monitors the NVLD switch. If the
NVLD switch does not close within a calibrated amount of time an error is detected.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
LEAK AT GAS CAP
VEHICLE HISTORY AND SERVICE BULLETIN INVESTIGATION
VISUAL AND PHYSICAL INSPECTION
VERIFY EVAPORATIVE EMISSION SYSTEM LEAK
EVAP PURGE SOLENOID OPERATION
EVAPORATIVE EMISSION LEAK DETECTION
GAS CAP
NVLD

TEST ACTION APPLICABILITY

1 Start by reading PCM DTC(s) and record the related Freeze Frame data in any All
DTC(s) are present.
Check the vehicle repair history.
If the vehicle has a repair history that pertains to the customer’s current complaint,
review the repair.
Inspect the vehicle for any aftermarket accessories that may have been installed
incorrectly.
Check for any service bulletin(s) related to the customer’s complaint or DTC(s).
If a service bulletin applies, follow the instructions per service bulletin.
Did the service bulletin repair the customer’s complaint?
Yes → Testing Complete.
Perform POWERTRAIN VERIFICATION TEST VER - 6.
No → Go To 2

158
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0456-EVAP SYSTEM SMALL LEAK — Continued

TEST ACTION APPLICABILITY

2 Check for any related TSBs before continuing. All
NOTE: The difference in ambient temperature, outside temp VS shop temp,
may conceal a leak, it is best to perform this test after the vehicle’s
temperature has stabilized in the work area.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 3
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 6.

3 Perform a visual and physical inspection of the entire Evaporative Emission system. All
Check for the following conditions:
- Holes or cracks
- Loose seal points
- Evidence of damaged components
- Incorrect routing of hoses and tubes
- Fuel Cap gasket seal
Were any of the above conditions found?
Yes → Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

No → Go To 4

159
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0456-EVAP SYSTEM SMALL LEAK — Continued

TEST ACTION APPLICABILITY

4 To continue testing you will need Miller Tool #8404 Evaporative Emission Leak All
Detector (EELD).
WARNING: Keep lit cigarettes, sparks, flames, and other ignition sources
away from the test area to prevent the ignition of explosive gases. Keep the
test area well ventilated.
NOTE: The fuel tank should have between 20% and 80% of fuel tank capacity
to properly test the Evap system.
Connect the red power lead of the EELD to the battery positive terminal and the
black ground lead to battery negative terminal.
NOTE: See Charts and Graph support material EELD Calibration Setup for
an example.
Block the vent hose of the EVAP Canister.
Connect shop air to the EELD.
Set the smoke/air control switch to AIR.
Insert the tester’s AIR supply tip (clear hose) into the appropriate calibration orifice
on the tester’s control panel (based on DTC leak size).
Press the remote smoke/air start button.
Position the red flag on the air flow meter so it is aligned with the indicator ball.
When the calibration is complete, release the remote button. The EELD flow meter
is now calibrated in liters per minute to the size leak indicated by the DTC set in the
PCM.
Install the service port adapter #8404-14 on the vehicle’s service port (if equipped) or
install #8404-ADP service adaptor in the filter line.
Connect the Air supply hose from the EELD to the service port (if equipped) or
#8404-ADP in the filter line.
Press the remote button to activate AIR flow.
NOTE: Larger volume fuel tanks, lower fuel levels or if the vehicle is
equipped with a Flow Management Valve may indicate high flow and will
require 4 to 5 minutes to fill
Compare the flow meter indicator ball reading to the red flag.
ABOVE the red flag indicates a leak present.
BELOW the red flag indicates a sealed system.
Is the indicator ball above the red flag?

Yes → Go To 5
No → Refer to the Freeze Frame data recorded in Step 1. If the data
indicates that the vehicle was in motion when the DTC was set,
verify that all hoses are properly connected. Test Complete.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

160
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0456-EVAP SYSTEM SMALL LEAK — Continued

TEST ACTION APPLICABILITY

5 NOTE: A thorough visual inspection of the Evap system hoses, tubes, and All
connections may save time in your diagnosis. Look for any physical damage
or signs of wetness at connections. The strong smell of fuel vapors may aid
diagnosis also.
To continue testing, you will need Miller Tool #8404 Evaporative Emissions Leak
Detector (EELD).
Remove the Air supply hose from the service port or the #8404-ADP adapter.
Connect the SMOKE supply tip (black hose) to the service port (if equipped) or to the
#8404-ADP adapter.
Set the smoke/air control switch to SMOKE.
NOTE: The flow meter indicator ball will not move at this point.
Press the remote smoke/air start button.
NOTE: Make sure that smoke has filled the EVAP system by continuing to
press the remote smoke/air start button, remove the vehicle fuel cap, and
wait for the smoke to exit. Once smoke is indicated reinstall the fuel cap.
NOTE: For optimal performance, introduce smoke into the system for an
additional 60 seconds; continue introducing smoke at 15 second intervals,
as necessary.
While still holding the remote smoke/air start button, use the white light (#8404-
CLL) to follow the EVAP system path, and look for the source of the leak indicated by
exiting smoke.
If a leak is concealed from view (i.e., top of fuel tank), release the remote smoke/air
start button, and use the ultraviolet (UV) black light #8404-UVL and the yellow
goggles 8404-20 to look for residual traces of dye that are left behind by the smoke.
The exiting smoke deposits a residual fluid that is either bright green or bright
yellow in color when viewed with a UV light.
NOTE: The EVAP System is divided into three zones. Possible leaking areas
can be from any of the three Zones.
ZONE 1.
- Fuel tank valves (control valve and inlet check valve).
- Cracked, cut, warped, or missing primary fuel filler cap to fuel filler tube seal.
- Out of round fuel filler tube.
- Fuel filler tube to fuel filler hose connection.
- Fuel filler hose to tank connection.
- Fuel tank shell.
- Fuel pump module attachment.
- Gas cap loose or seal damaged.
- Gas cap internal valve.
- Damaged or disconnected EVAP system components.
ZONE 2.
- EVAP hoses loose or disconnected.
- Damaged or disconnected EVAP system components.
- Canister seals/hoses leaking.
- Canister housing.
- NVLD Assembly.
ZONE 3.
- EVAP Purge valve.
- EVAP hoses loose, cracked, or disconnected.
NOTE: Carefully inspect the vent side of the EVAP Canister. Due to the
filtering system in the canister the smoke or dye may or may not be visible.
Introducing smoke into the filtered side of the canister may assist in
locating the leak.
Was a leak found?
Yes → Go To 6

No → Go To 7

161
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0456-EVAP SYSTEM SMALL LEAK — Continued

TEST ACTION APPLICABILITY

6 Remove the SMOKE supply tip (black hose) from the Service port (if equipped) or to All
the #8404-ADP adapter.
Install gas cap adapter, Miller Tool #8382 (1/4 turn cap) or #6922 (screw cap) and
#8399 (secondary seal depressor) and repeat test 5.
Was a leak at the gas cap adapter?

Yes → Replace the fuel filler tube assembly.

Perform POWERTRAIN VERIFICATION TEST VER - 6.

No → Replace the gas cap.

Perform POWERTRAIN VERIFICATION TEST VER - 6.

7 To continue testing you will need Miller Tool #8404 Evaporative Emission Leak All
Detector (EELD).
WARNING: Keep lit cigarettes, sparks, flames, and other ignition sources
away from the test area to prevent the ignition of explosive gases. Keep the
test area well ventilated.
Connect the red power lead of EELD to the battery positive terminal and the black
ground lead to battery negative terminal.
Disconnect the vacuum hoses at he Evap Purge Solenoid.
Connect the SMOKE supply tip (black hose) to the service port (if equipped) or to the
#8404-ADP adapter.
Set the smoke/air control switch to SMOKE.
Press the remote smoke/air start button.
NOTE: Below is an optional method of checking the purge valve for leaks if
the EELD is unavailable.
Turn the ignition off.
Disconnect the vacuum supply hoses from the EVAP Purge Solenoid.
Using a hand vacuum pump, apply 10 in Hg to the 9CAN9 side of the EVAP Purge
Solenoid.
Observe the vacuum gauge for at least 15 seconds.
With the DRBIIIt, actuate the Evap Purge Solenoid.
NOTE: If the Evap Purge Solenoid does not hold a vacuum, it will need to be
replaced.
Is smoke visible from the Evap Purge Solenoid?
Yes → Replace the Evap Purge Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 6.
No → Replace the NVLD Assembly.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

161A
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0457-LOOSE FUEL FILL CAP

When Monitored and Set Condition:

P0457-LOOSE FUEL FILL CAP

When Monitored: Engine Running. Cold start test. Fuel Level greater than 12%. Ambient
Temperature between 4°C and 32°C (39°F and 89°F) Close Loop fuel system. Test runs
when small leak test is maturing.
Set Condition: The PCM activates the EVAP Purge Solenoid to pull the EVAP system into
a vacuum to close the NVLD switch. Once the NVLD switch is closed, the PCM turns the
EVAP Purge Solenoid off to seal the EVAP system. If the NVLD switch reopens before the
calibrated amount of time after a fuel tank fill, an error is detected. Two Trip Fault. Three
good trips to turn off the MIL.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
LOOSE OR MISSING FUEL FILL CAP
INTERMITTENT CONDITION
NVLD SERVICE TEST
EVAPORATIVE EMISSION LEAK DETECTION
EVAP PURGE SOLENOID OPERATION
NVLD SWITCH OPERATION

TEST ACTION APPLICABILITY

1 NOTE: After the PCM has determined the leak test inconclusive and sees an All
increase in fuel level, the PCM will request the GAS CAP indicator on to
inform the customer that the gas fill cap is loose or off.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

162
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0457-LOOSE FUEL FILL CAP — Continued

TEST ACTION APPLICABILITY

2 Perform a visual and physical inspection of the Fuel Fill Cap and the fill tube. All
Check for the follow conditions:
- Improper installation of Fuel Fill Cap
- Loose or missing Fuel Filler Cap
- Holes or cracks
- Damaged Locking tabs on Cap and/or fill tube
- Damaged seal points on Cap and/or fill tube
- Fuel Fill Cap gasket seal
Were any of the above conditions found?

Yes → Repair or replace the fuel fill cap as needed. Ensure proper fuel
fill cap installation. Once the repair is complete continue to step
3.
Perform POWERTRAIN VERIFICATION TEST VER - 6.
No → Go To 3

3 With the DRBIIIt, perform the NVLD Service Test. All

Did the NVLD Service Test pass?
Yes → Test Complete.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

No → Go To 4

163
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0457-LOOSE FUEL FILL CAP — Continued

TEST ACTION APPLICABILITY

4 To continue testing you will need Miller Tool #8404 Evaporative Emission Leak All
Detector (EELD).
WARNING: Keep lighted cigarettes, sparks, flames, and other ignition
sources away from the test area to prevent the ignition of explosive gases.
Keep the test area well ventilated.
NOTE: The fuel tank should have between 20% and 80% of fuel tank capacity
to properly test the Evap system.
Connect the red power lead of the EELD to the battery positive terminal and the
black ground lead to battery negative terminal.
NOTE: See Charts and Graph support material EELD Calibration Setup for
an example.
Block the vent hose of the EVAP Canister.
Connect shop air to the EELD.
Set the smoke/air control switch to AIR.
Insert the tester’s AIR supply tip (clear hose) into the appropriate calibration orifice
on the tester’s control panel (based on DTC leak size).
Press the remote smoke/air start button.
Position the red flag on the air flow meter so it is aligned with the indicator ball.
When the calibration is complete, release the remote button. The EELD is now
calibrated the flow meter in liters per minute to the size leak indicated by the DTC
set in the PCM.
Install the service port adapter #8404-14 on the vehicle’s service port (if equipped) or
install the #8404-ADP service adapter in the NVLD filter line.
Connect the Air supply hose from the EELD to the service port.
Press the remote button to activate AIR flow.
NOTE: Larger volume fuel tanks, lower fuel levels or if the vehicle is
equipped with a Flow Management Valve may indicate high flow and will
require 4 to 5 minutes to fill
Compare the flow meter indicator ball reading to the red flag.
ABOVE the red flag indicates a leak present.
BELOW the red flag indicates a sealed system.
Is the indicator ball above the red flag?

Yes → Go To 5
No → Go To 8

164
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0457-LOOSE FUEL FILL CAP — Continued

TEST ACTION APPLICABILITY

5 NOTE: A thorough visual inspection of the Evap system hoses, tubes, and All
connections may save time in your diagnosis. Look for any physical damage
or signs of wetness at connections. The strong smell of fuel vapors may aid
diagnosis also.
To continue testing, you will need Miller Tool #8404 Evaporative Emissions Leak
Detector (EELD).
Remove the Air supply hose from the service port.
Connect the SMOKE supply tip (black hose) to the service port.
Set the smoke/air control switch to SMOKE.
NOTE: The flow meter indicator ball will not move in the smoke mode.
Press the remote smoke/air start button.
NOTE: Make sure that smoke has filled the EVAP system by continuing to
press the remote smoke/air start button, remove the vehicle fuel cap, and
wait for the smoke to exit. Once smoke is indicated reinstall the fuel cap.
NOTE: For optimal performance, introduce smoke into the system for an
additional 60 seconds; continue introducing smoke at 15 second intervals,
as necessary.
While still holding the remote smoke/air start button, use the white light (#8404-
CLL) to follow the EVAP system path, and look for the source of the leak indicated by
exiting smoke.
If a leak is concealed from view (i.e., top of fuel tank), release the remote smoke/air
start button, and use the ultraviolet (UV) black light #8404-UVL and the yellow
goggles 8404-20 to look for residual traces of dye that is left behind by the smoke.
The exiting smoke deposits a residual fluid that is either bright green or bright
yellow in color when viewed with a UV light.
NOTE: Carefully inspect the vent side of the EVAP Canister. Due to the
filtering system in the canister the smoke may not be as thick. Introducing
smoke into the filtered side of the canister may assist in locating the leak.
Was a leak found?
Yes → Repair or replace the leaking component as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 6.
No → Go To 6

6 NOTE: After disconnecting the Evap Purge Solenoid vacuum connections, All
inspect the lines and solenoid for any signs of contamination from the EVAP
Canister. This may indicate a faulty vent valve. Replace/repair as necessary.
Turn the ignition off.
Disconnect the vacuum hoses at the Evap Purge Solenoid.
Using a hand vacuum pump, apply 10 in Hg to the 9CAN9 of the EVAP Purge
Solenoid.
NOTE: Monitor the vacuum gauge for at least 15 seconds.
Does the EVAP Purge Solenoid hold vacuum?

Yes → Go To 7
No → Replace the Evap Purge Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 6.

165
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0457-LOOSE FUEL FILL CAP — Continued

TEST ACTION APPLICABILITY

7 Reconnect all vacuum hoses. All
Start the engine.
Allow the engine to idle.
Using the DRBIIIt, perform the NVLD FORCED MONITOR TEST.
Monitor the NVLD Switch.
As the test runs, the NVLD Switch should go from an OPEN state to
CLOSED. After the vacuum is released form the EVAP system the Switch
state will return to OPEN.
Did the NVLD Switch operate as described above?

Yes → Go To 8

No → Replace the NVLD Assembly.

Perform POWERTRAIN VERIFICATION TEST VER - 6.

8 WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A All

DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Review the DRBIIIt Freeze Frame information. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
NOTE: Make Ensure the gas cap meets OEM specifications.
Perform a visual and physical inspection of the entire Evaporative Emission system.
Check for the following conditions:
- Holes or cracks
- Loose seal points
- Evidence of damaged components
- Incorrect routing of hoses and tubes
- Fuel Cap gasket seal
Were any of the above conditions found?

Yes → Repair as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 6.
No → Test Complete.

166
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0461-FUEL LEVEL SENSOR NO.1 PERFORMANCE

When Monitored and Set Condition:

P0461-FUEL LEVEL SENSOR NO.1 PERFORMANCE

When Monitored: TEST #1: With the ignition on, the fuel level is compared to the
previous key down after a 20 second delay. TEST #2: The PCM monitors the fuel level at
ignition on.
Set Condition: TEST #1: If the PCM does not see a difference in fuel level of greater than
0.1 volt the test will fail. TEST #2: If the PCM does not see a change in the fuel level of
.1765 over a set amount of miles the test will fail.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
VISUALLY INSPECT FUEL TANK
(N4) FUEL LEVEL SIGNAL CIRCUIT OPEN
(N4) FUEL LEVEL SIGNAL CIRCUIT SHORTED TO GROUND
(K900) SENSOR GROUND CIRCUIT OPEN
INTERNAL INSPECTION OF THE FUEL TANK
FUEL LEVEL SENSOR

TEST ACTION APPLICABILITY

1 NOTE: Diagnose P0462 or P0463 first, if set along with P0461. All
NOTE: Inspect the Fuel Pump Module harness connector for any corrosion
or damage.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Visually inspect the Fuel Tank for damage that may restrict the Fuel Sending Unit All
float from moving.
Is the Fuel Tank OK?

Yes → Go To 3
No → Replace the Fuel Tank as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

167
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0461-FUEL LEVEL SENSOR NO.1 PERFORMANCE — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the Fuel Pump Module harness connector.
Disconnect the C2 and C3 PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (N4) Fuel Level Signal circuit from the Fuel Pump
Module harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 4

No → Repair the open in the (N4) Fuel Level Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Measure the resistance between ground and the (N4) Fuel Level Signal circuit at the All
Fuel Pump Module harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (N4) Fuel Level Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the Fuel Pump
Module harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6
No → Repair the open in the (K900) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 WARNING: The fuel system is under a constant pressure even with the All
engine off. Before opening the fuel system the fuel pressure must be release.
Relieve the fuel pressure in accordance with the service information.
Remove the Fuel Tank per Service Information.
Remove the Fuel Pump Module.
Visually inspect the inside of the Fuel Tank for any obstructions or deformities.
Inspect the Fuel Pump Module Float arm for damage.
Were any problems found?

Yes → Repair or replace as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 7

7 If there are no possible causes remaining, view repair. All

Repair
Replace the Fuel Level Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

168
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0462-FUEL LEVEL SENSOR NO.1 LOW

When Monitored and Set Condition:

P0462-FUEL LEVEL SENSOR NO.1 LOW

When Monitored: Ignition on and battery voltage above 10.4 volts.
Set Condition: The fuel level sensor signal voltage goes below 0.0196 of a volt for more
than 90 seconds.

POSSIBLE CAUSES
FUEL LEVEL SENSOR VOLTAGE BELOW 0.0196 OF A VOLT
FUEL LEVEL SENSOR
(N4) FUEL LEVEL SIGNAL CIRCUIT SHORTED TO GROUND
(N4) FUEL LEVEL SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
With the DRBIIIt, read the Fuel Level Sensor voltage.
Is the Fuel Level Sensor voltage below 0.0196 of a volt?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the Fuel Pump Module harness connector.
Ignition on, engine not running.
With the DRBIIIt, read the Fuel Level Sensor voltage.
Did the Fuel Level Sensor voltage change from below 0.4 of a volt to above 4.0 volts?

Yes → Replace the Fuel Level Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

3 Turn the ignition off. All

Disconnect the C2 and C3 PCM harness connectors.
Measure the resistance between ground and the (N4) Fuel Level Signal circuit at the
Fuel Level Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (N4) Fuel Level Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

169
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0462-FUEL LEVEL SENSOR NO.1 LOW — Continued

TEST ACTION APPLICABILITY

4 Measure the resistance between the (N4) Fuel Level Signal circuit and the (K900) All
Sensor ground circuit at the Fuel Pump Module harness connector.
Is the resistance below 5.0 ohms?

Yes → Repair the short between the (K900) Sensor ground and the (N4)
Fuel Level Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

170
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0463-FUEL LEVEL SENSOR NO.1 HIGH

When Monitored and Set Condition:

P0463-FUEL LEVEL SENSOR NO.1 HIGH

When Monitored: Ignition on and battery voltage above 10.4 volts.
Set Condition: The fuel level sensor signal voltage at the PCM goes above 4.9 volts for
more than 90 seconds.

POSSIBLE CAUSES
FUEL LEVEL SENSOR VOLTAGE ABOVE 4.9 VOLTS
FUEL LEVEL SENSOR
(N4) FUEL LEVEL SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(N4) FUEL LEVEL SIGNAL CIRCUIT OPEN
(K900) SENSOR GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the Fuel Level Sensor voltage.
Is the Fuel Level Sensor voltage above 4.9 volts?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the Fuel Pump Module electrical harness connector.
Connect a jumper wire between the (N4) Fuel Level Signal circuit and the (K900)
Sensor ground circuit at the Fuel Pump Module harness connector.
Ignition on, engine not running.
With the DRBIIIt, read the Fuel Level Sensor voltage.
Did the Fuel Level Sensor voltage change from above 4.8 volts to below 0.4 of a volt?
Yes → Replace the Fuel Level Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

NOTE: Remove the jumper wire before continuing.

171
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0463-FUEL LEVEL SENSOR NO.1 HIGH — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C2 and C3 PCM harness connectors.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Measure the voltage on the (N4) Fuel Level Signal circuit at the Fuel Pump Module
harness connector.
Is the voltage above 5.3 volts?

Yes → Repair the short to voltage in the (N4) Fuel Level Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

4 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (N4) Fuel Level Signal circuit from the Fuel Pump
Module harness connector to the appropriate terminal in special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 5

No → Repair the open in the (N4) Fuel Level Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the Fuel Pump
Module harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6
No → Repair the open in the (K900) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

172
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0480-COOLING FAN NO.1 CONTROL CIRCUIT

When Monitored and Set Condition:

P0480-COOLING FAN NO.1 CONTROL CIRCUIT

When Monitored: With the ignition on. Battery voltage greater than 10 volts.
Set Condition: An open or shorted circuit is detected in the radiator fan relay control
circuit.

POSSIBLE CAUSES
LOW SPEED RADIATOR FAN RELAY OPERATION
LOW SPEED RADIATOR FAN RELAY
(F20) FUSED IGNITION SWITCH OUTPUT CIRCUIT
(A16) FUSED B+ CIRCUIT
(N201) LOW SPEED RAD FAN RELAY CONTROL CIRCUIT OPEN
(N201) LOW SPEED RAD FAN RELAY CONTROL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, actuate the Low Speed Radiator Fan Relay.
Is the Radiator Fan Relay cycling on and off?
Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 2

2 Turn the ignition off. All

Remove the Low Speed Radiator Fan Relay from the PDC.
Measure the resistance of the Low Speed Radiator Fan Relay Coil by measuring
between the (F20) Fused Ignition Switch terminal and the (N201) Control circuit
terminal at the Relay .
Is the resistance between 60 and 80 ohms?

Yes → Go To 3
No → Replace the Low Speed Radiator Fan Relay.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

173
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0480-COOLING FAN NO.1 CONTROL CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Ignition on, engine not running. All
Using a 12-volt test light connected to ground, probe the (F20) Fused Ignition Switch
Output circuit at the Relay connector in the PDC.
Does the test light illuminate brightly?
Yes → Go To 4

No → Repair the open or short to ground in the (F20) Fused Ignition

Output. Inspect the related fuse and repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Turn the ignition off. All

Remove the Low Speed Radiator Fan Relay from the PDC.
Ignition on, engine not running.
Measure the voltage on the (A16) Fused B+ circuits in the PDC.
Is the voltage above 11.0 volts?

Yes → Go To 5
No → Repair the open or short to ground in the (A16) Fused B+ circuits.
Inspect the related fuse and repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Disconnect the C3 PCM harness connector. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (N201) Low Speed Rad Fan Relay Control circuit from
the PDC to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6

No → Repair the open in the (N201) Low Speed Rad Fan Relay Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Measure the resistance between ground and the (N201) Low Speed Rad Fan Relay All
Control circuit at the PDC.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (N201) Low Speed Rad Fan
Relay Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 7

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

174
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0481-COOLING FAN NO.2 CONTROL CIRCUIT

When Monitored and Set Condition:

P0481-COOLING FAN NO.2 CONTROL CIRCUIT

When Monitored: With the ignition on. Battery voltage greater than 10 volts.
Set Condition: An open or shorted circuit is detected in the high speed radiator fan relay
control circuit. One Trip Fault.

POSSIBLE CAUSES
HIGH SPEED RADIATOR FAN RELAY OPERATION
HIGH SPEED RADIATOR FAN RELAY
(F20) FUSED IGNITION SWITCH OUTPUT CIRCUIT
(A16) FUSED B+ CIRCUIT
(N112) HIGH SPEED RAD FAN RELAY CONTROL CIRCUIT OPEN
(N112) HIGH SPEED RAD FAN RELAY CONTROL CIRCUIT SHORT TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, actuate the High Speed Radiator Fan Relay.
Is the High Speed Radiator Fan Relay operating?
Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 2

2 Turn the ignition off. All

Remove the High Speed Radiator Fan Relay from the PDC.
Measure the resistance of the High Speed Radiator Fan Relay between the (F20)
Fused Ignition Switch Output terminal and the (N112) High Speed Rad Fan Relay
Control terminal.
Is the resistance between 60 to 85 ohms?

Yes → Go To 3
No → Replace the High Speed Radiator Fan Relay.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

175
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0481-COOLING FAN NO.2 CONTROL CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Ignition on, engine not running. All
Using a 12-volt test light connected to ground, probe the (F20) Fused Ignition Switch
Output circuit at the Relay connector in the PDC.
Does the test light illuminate brightly?
Yes → Go To 4

No → Repair the open or short to ground in the (F20) Fused Ignition

Output. Inspect the related fuse and repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Using a 12-volt test light connected to ground probe the (A16) Fused B+ circuit in the All
PDC.
Does the test light illuminate brightly?

Yes → Go To 5
No → Repair the open or short to ground (A16) Fused B+ circuit. Inspect
the related fuse and repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Turn the ignition off. All

Disconnect the C3 PCM harness connector.
Measure the resistance of the (N112) High Speed Rad Fan Relay Control circuit from
the PDC to the PCM harness connector.
Is the resistance below 5.0 ohms?
Yes → Go To 6
No → Repair the open in the (N112) High Speed Rad Fan Relay Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Measure the resistance between ground and the (N112) High Speed Rad Fan Relay All
Control circuit in the PDC.
Is the resistance below 5.0 ohms?
Yes → Repair the short to ground in the (N112) High Speed Rad Fan
Relay Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 7

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

176
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
Symptom:
P0498-NVLD CANISTER VENT VALVE SOLENOID CIRCUIT LOW

When Monitored and Set Condition:

P0498-NVLD CANISTER VENT VALVE SOLENOID CIRCUIT LOW

When Monitored: Engine running.
Set Condition: The PCM detects a short in the NVLD Canister vent solenoid circuits. One
trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
VEHICLE HISTORY AND SERVICE BULLETIN INVESTIGATION
NVLD SOLENOID
NVLD SOL CONTROL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Start by reading PCM DTC(s) and record the related Freeze Frame data in any All
DTC(s) are present.
Check the vehicle repair history.
If the vehicle has a repair history that pertains to the customer’s current complaint,
review the repair.
Inspect the vehicle for any aftermarket accessories that may have been installed
incorrectly.
Check for any service bulletin(s) related to the customer’s complaint or DTC(s).
If a service bulletin applies, follow the instructions per service bulletin.
Did the service bulletin repair the customer’s complaint?
Yes → Testing Complete.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 2

2 Ignition on, engine not running. All

With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 3
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

177
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0498-NVLD CANISTER VENT VALVE SOLENOID CIRCUIT LOW —
Continued
TEST ACTION APPLICABILITY
3 Turn the ignition off. All
Disconnect the NVLD electrical harness connector.
Measure the resistance of the NVLD Solenoid coil.
Is the resistance between 7.5 to 8.5 ohms?
Yes → Go To 4

No → Replace the NVLD Assembly.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Disconnect the PCM harness connector. All

Measure the resistance between ground and the NVLD Sol Control circuit at the
NVLD electrical harness connector.
Is the resistance below 5.0 ohms?

Yes → Repair the short to ground in the NVLD Solenoid Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

178
bY dR.dEaDhEaD
 DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
Symptom:
P0499-NVLD CANISTER VENT VALVE SOLENOID CIRCUIT HIGH

When Monitored and Set Condition:

P0499-NVLD CANISTER VENT VALVE SOLENOID CIRCUIT HIGH

When Monitored: Engine running.
Set Condition: The PCM detects an open in the NVLD Canister vent solenoid circuits.
One trip Fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
VEHICLE HISTORY AND SERVICE BULLETIN INVESTIGATION
NVLD SOLENOID
NVLD SOL CONTROL CIRCUIT SHORTED TO BATTERY VOLTAGE
NVLD SOL CONTROL CIRCUIT OPEN
GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Start by reading PCM DTC(s) and record the related Freeze Frame data in any All
DTC(s) are present.
Check the vehicle repair history.
If the vehicle has a repair history that pertains to the customer’s current complaint,
review the repair.
Inspect the vehicle for any aftermarket accessories that may have been installed
incorrectly.
Check for any service bulletin(s) related to the customer’s complaint or DTC(s).
If a service bulletin applies, follow the instructions per service bulletin.
Did the service bulletin repair the customer’s complaint?
Yes → Testing Complete.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 2

2 Ignition on, engine not running. All

With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 3
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

179
bY dR.dEaDhEaD
DRIVEABILITY - NGC
2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
P0499-NVLD CANISTER VENT VALVE SOLENOID CIRCUIT HIGH —
Continued
TEST ACTION APPLICABILITY
3 Turn the ignition off. All
Disconnect the NVLD Assembly harness connector.
Measure the resistance of the NVLD Solenoid coil.
Is the resistance between 7.5 to 8.5 ohms?
Yes → Go To 4

No → Replace the NVLD Assembly.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Turn the ignition off. All

Disconnect the NVLD Assembly harness connector.
Disconnect the PCM harness connector.
Take this measurement with the Ignition in the off (lock) position and in the Ignition
on, engine off position.
Measure the voltage on the NVLD Sol Control circuit in the NVLD Assembly harness
connector.
Is the voltage above 1.0 volt?

Yes → Repair the short to battery voltage in the NVLD Solenoid Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 Turn the ignition off. All

Disconnect the NVLD Assembly harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the NVLD Sol Control circuit from the NVLD Assembly
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 6
No → Repair the open in the NVLD Sol Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Turn the ignition off. All

Disconnect the NVLD Assembly harness connector.
Measure the resistance between the Ground circuit and ground.
Is the resistance below 5.0 ohms?

Yes → Go To 7
No → Repair the open in the Ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

180
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0501-VEHICLE SPEED SIGNAL PERFORMANCE

When Monitored and Set Condition:

P0501-VEHICLE SPEED SIGNAL PERFORMANCE

When Monitored: With the engine running, transmission not in park or neutral, brakes
not applied, and engine rpm greater than 1500.
Set Condition: This code will set if no vehicle speed signal is received from the Body
Control Module for more than 11 seconds for 2 consecutive trips.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
(K75) VSS CIRCUIT SHORTED TO BATTERY VOLTAGE
RESISTANCE IN THE (F856) 5-VOLT SUPPLY
RESISTANCE BETWEEN GROUND AND THE (F856) 5-VOLT SUPPLY CIRCUIT
VEHICLE SPEED SENSOR
RESISTANCE BETWEEN GROUND AND THE (K75) VSS SIGNAL CIRCUIT
(K75) VSS SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Disconnect the Vehicle Speed Sensor harness connector. All

Disconnect the C1 PCM harness connector.
Ignition on, engine not running.
Measure the voltage on the (K75) Vehicle Speed Sensor Signal circuit in the Vehicle
Speed Sensor harness connector.
Is the voltage above 5.2 volts?

Yes → Repair the short to voltage in the (K75) VSS Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 3

181
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0501-VEHICLE SPEED SIGNAL PERFORMANCE — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Connect the PCM harness connector.
Ignition on, engine not running.
Measure the voltage on the (F856) 5-volt Supply circuit in the Vehicle Speed Sensor
harness connector.
Is the voltage between 4.5 to 5.2 volts?

Yes → Go To 4

No → Go To 7

4 With the DRBIIIt, monitor the Vehicle Speed Sensor voltage with the Sensor harness All
connector disconnected.
Is the voltage above 1.2 volts?

Yes → Replace the Vehicle Speed Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5

5 Turn the ignition off. All

Disconnect the C1 and C2 PCM harness connectors.
Measure the resistance between ground and the (K75) Vehicle Speed Sensor Signal
circuit at the Vehicle Speed Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the excessive resistance between ground and the (K75)
VSS Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

6 Measure the resistance between the (K75) VSS Signal circuit and the (K900) Sensor All
ground circuit in the Vehicle Speed Sensor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short between the (K900) Sensor ground and the (K75)
VSS Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 9

7 Turn the ignition off. All

Disconnect the C1 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (F856) 5-volt Supply circuit from the Vehicle Speed
Sensor harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 8
No → Repair the excessive resistance in the (F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

182
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0501-VEHICLE SPEED SIGNAL PERFORMANCE — Continued

TEST ACTION APPLICABILITY

8 Measure the resistance between ground and the (F856) 5-volt Supply circuit in the All
Vehicle Speed Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the excessive resistance between ground and the (F856)
5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 9

9 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

183
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0506-IDLE SPEED PERFORMANCE LOWER THAN EXPECTED

When Monitored and Set Condition:

P0506-IDLE SPEED PERFORMANCE LOWER THAN EXPECTED

When Monitored: With the engine running at idle, MAF <250 mg/tdc, air temp >-17.8°C
(0°F) and <-7°C (19.4°F) enable after coolant temp >70°C (158°F) or air temp >-7°C
(19.4°F), coolant temp >-7°C (19.4°F) <130°C (266°F), canister purge <100% duty cycle,
and no VSS, MAF/MAP, ECT, TPS, ETC, CRK Sensor DTCs nor any fuel system or injector
DTCs.
Set Condition: Engine speed is 100 RPM or more below idle speed for 7 seconds. Two Trip
Fault. Three good trips to turn off the MIL.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
AIR INDUCTION SYSTEM
IAC OPERATION
PCM

TEST ACTION APPLICABILITY

1 NOTE: If any other DTCs are present, they must be diagnosed and repaired All
before continuing this test.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Inspect the Air Induction System for the following problems. All
Restrictions: Dirty Air Cleaner, Foreign material trap in the air intake tube, etc.
Leaks: Air Intake tube connection, Air Cleaner housing, etc.
Remove the IAC and inspect for foreign debris.
Check the MAP Sensor for proper installation.
Were any problems found?
Yes → Repair or replace as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

184
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0506-IDLE SPEED PERFORMANCE LOWER THAN EXPECTED —

Continued
TEST ACTION APPLICABILITY
3 Inspect the throttle plate for carbon build up or other restrictions. All
Verify that the throttle cable between the Accelerator Pedal and the Throttle body is
not binding.
Make sure the throttle plate is in the idle position.
Remove the IAC Motor and actuate the IAC Motor with the DRBIIIt to verify proper
operation.
Install the IAC Motor.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
With the vehicle is running, lightly tap on IAC Motor, with your hand, and listen for
idle to raise.
Were any problems found?

Yes → Repair or replace as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

185
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0507-IDLE SPEED PERFORMANCE HIGHER THAN EXPECTED

When Monitored and Set Condition:

P0507-IDLE SPEED PERFORMANCE HIGHER THAN EXPECTED

When Monitored: With the engine running at idle, MAF <250 mg/tdc, air temp >-17.8°C
(0°F) and <-7°C (19.4°F) enable after coolant temp >70°C (158°F) or air temp >-7°C
(19.4°F), coolant temp >-7°C (19.4°F) <130°C (266°F), canister purge <100% duty cycle,
and no VSS, MAF/MAP, ECT, TPS, ETC, CRK Sensor DTCs nor any fuel system or injector
DTCs.
Set Condition: Engine speed is 200 RPM or more above idle speed for 7 seconds. Two Trip
Fault. Three good trips to turn off the MIL.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
AIR INDUCTION SYSTEM
VACUUM LEAKS
IAC OPERATION
PCM

TEST ACTION APPLICABILITY

1 NOTE: If any other DTCs are present, they must be diagnosed and repaired All
before continuing this test.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Inspect the Air Induction System for the following problems. All
Restrictions: Dirty Air Cleaner, Foreign material trap in the air intake tube, etc.
Leaks: Air Intake tube connection, Air Cleaner housing, etc.
Were any problems found?
Yes → Repair or replace as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

186
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0507-IDLE SPEED PERFORMANCE HIGHER THAN EXPECTED —

Continued
TEST ACTION APPLICABILITY
3 Start the engine. All
Inspect the vehicle for external vacuum leaks.
Inspect the engine for internal leaks.
Were any vacuum leaks found?
Yes → Repair the vacuum leak as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

4 Inspect the throttle body plate for carbon build up or other restrictions. All
Verify that the throttle cable between the Accelerator Pedal and Throttle Body is not
binding.
Make sure the throttle plate is resting on the stop at idle.
Remove the IAC Motor and actuate the IAC Motor with the DRBIIIt to verify proper
operation.
Install the IAC Motor.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
While the vehicle is running, lightly tap on IAC Motor, with your hand, and listen for
idle to raise.
Were any problems found?
Yes → Repair or replace as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

187
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0508-IAC VALVE SIGNAL CIRCUIT LOW

When Monitored and Set Condition:

P0508-IAC VALVE SIGNAL CIRCUIT LOW

When Monitored: Engine running. Battery voltage greater than 10 volts. IAC motor
operating.
Set Condition: The PCM senses a short to ground or battery voltage on the Linear Idle Air
Control (LIAC) control circuit for 2.75 seconds while the IAC motor is active.

POSSIBLE CAUSES
IAC MOTOR OPERATTION
IAC MOTOR
(K61) IAC CONTROL CIRCUIT SHORTED TO GROUND
(K961) IAC SIGNAL CIRCUIT OPEN
(K961) IAC SIGNAL CIRCUIT SHORTED TO GROUND
(K61) IAC CONTROL CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 NOTE: If the engine will not idle, maintain an engine speed between 800 and All
1500 RPM.
Start the engine.
Allow the engine to idle.
Check for vacuum leaks, proper PCV valve installation, proper MAP Sensor instal-
lation, and proper IAC installation.
With the DRBIIIt, read the IAC Current.
Is the IAC Current below 146 mA?

Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the IAC Motor harness connector.
Remove the IAC Motor.
NOTE: Inspect the IAC air passages for restriction and damage to the IAC
valve.
Measure the resistance across the IAC Motor pin terminals (component).
Is the resistance 9.7 +/- 1.0 ohms?

Yes → Go To 3

No → Replace the IAC Motor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

188
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0508-IAC VALVE SIGNAL CIRCUIT LOW — Continued

TEST ACTION APPLICABILITY

3 Disconnect the C2 PCM harness connector. All
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K961) IAC Signal circuit from the IAC Motor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 4
No → Repair the open in the (K961) IAC Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Measure the resistance between ground and the (K961) IAC Signal circuit in the IAC All
Motor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (K961) IAC Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K61) IAC Control circuit from the IAC Motor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6

No → Repair the open in the (K61) IAC Control circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Measure the resistance between ground and the (K61) IAC Control circuit in the IAC All
Motor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (K61) IAC Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 7

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

189
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0509-IAC VALVE SIGNAL CIRCUIT HIGH

When Monitored and Set Condition:

P0509-IAC VALVE SIGNAL CIRCUIT HIGH

When Monitored: Engine running. Battery voltage greater than 10 volts. IAC motor
operating.
Set Condition: The PCM senses a short to ground or battery voltage on the Linear Idle Air
Control (LIAC) control circuit for 2.75 seconds while the IAC motor is active.

POSSIBLE CAUSES
IAC MOTOR OPERATION
IAC MOTOR
(K961) IAC SIGNAL CIRCUIT SHORTED TO VOLTAGE
(K61) IAC CONTROL CIRCUIT SHORTED TO VOLTAGE
(K61) IAC CONTROL CIRCUIT SHORTED TO (K961) IAC SIGNAL CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 NOTE: If the engine will not idle, maintain an engine speed between 800 and All
1500 RPM.
Start the engine.
Allow the engine to idle.
Check for vacuum leaks, proper PCV valve installation, proper MAP Sensor instal-
lation, and proper IAC installation.
With the DRBIIIt, read the IAC Current.
Is the IAC Current above 999 mA?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITON Symptom (Diagnostic

Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the IAC Motor harness connector.
With the DRBIIIt, monitor the IAC Current.
Ignition on, engine not running.
Does the DRBIIIt display IAC Current at 0mA?

Yes → Replace the IAC Motor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

190
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0509-IAC VALVE SIGNAL CIRCUIT HIGH — Continued

TEST ACTION APPLICABILITY

3 With the DRBIIIt, actuate the ASD Relay. All
Measure the voltage on the (K961) IAC Signal circuit in the IAC Motor harness
connector.
Is the voltage above 0.5 of a volt?
Yes → Repair the short to voltage in the (K961) IAC Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 4

4 Measure the voltage on the (K61) IAC Control circuit in the IAC Motor harness All
connector.
Is the voltage above 0.5 of a volt?

Yes → Repair the short to voltage in the (K61) IAC Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 5
NOTE: Stop the ASD Relay actuation before continuing.

5 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
Measure the resistance across the (K961) IAC Signal circuit and the (K61) IAC
Control circuit in the IAC Motor harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the short between the (K61) IAC Control circuit and the
(K961) IAC Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 6

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

191
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0513-INVALID SKIM KEY

When Monitored and Set Condition:

P0513-INVALID SKIM KEY

When Monitored: Ignition on.
Set Condition: The PCM detects an invalid SKIM key.

POSSIBLE CAUSES
INCORRECT VIN IN PCM
NO COMMUNICATION WITH SKIM
NO VIN PROGRAMMED IN THE PCM
SKIM TROUBLE CODES SET
IGNITION KEY
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the PCM DTCs.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2
No → Go To 7

2 With the DRBIIIt, attempt to communicate with the SKIM. All

Can the DRBIIIt communicate with the SKIM?

Yes → Go To 3
No → Refer to symptom BUS +/- SIGNAL OPEN FROM SKIM in the
COMMUNICATION category.
Perform SKIS VERIFICATION.

3 With the DRBIIIt, check for SKIM DTCs. All

Are any DTCs present in the SKIM?

Yes → Refer to BODY information for the related symptom(s).

Perform SKIS VERIFICATION.

No → Go To 4

4 With the DRBIIIt, display the VIN that is programmed in the PCM. All
Has a VIN been programmed into the PCM?
Yes → Go To 5

No → Program the correct VIN into the PCM and retest.

Perform SKIS VERIFICATION.

192
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0513-INVALID SKIM KEY — Continued

TEST ACTION APPLICABILITY

5 With the DRBIIIt, display the VIN that is programmed in the PCM. All
Was the correct VIN programmed into the PCM?

Yes → Go To 6
No → Replace and program the Powertrain Control Module per Service
Information.
Perform SKIS VERIFICATION.

6 Turn the ignition off. All

Replace and program the Sentry Key Immobilizer Module per Service Information.
Ignition on, engine not running.
With the DRBIIIt, erase all SKIM and PCM DTCs.
Attempt to start and idle the engine.
With the DRBIIIt, read the PCM DTCs.
Does the DRBIIIt display this code?

Yes → NOTE: Before continuing, check the PCM harness connector

termnals for corrosion, damage, or terminal push out. Repair as
necessary. Replace and program the Powertrain Control Module
per Service Information.
Perform SKIS VERIFICATION.
No → Test Complete.

7 NOTE: You must obtain the SKIM pin number. All

NOTE: This DTC could have been set if the SKIM harness connector was
disconnected, or if the SKIM was replaced recently.
NOTE: All keys that the customer uses for this vehicle must be tested to
verify they are operating properly.
Verify the correct VIN is programmed into the PCM and SKIM.
Turn the ignition off.
With the next customer key turn the ignition key on and crank the engine to start.
With the DRBIIIt, read the PCM DTCs. Look for P0513.
Is the Good Trip Counter for DTC P0513 displayed and equal to 0?

Yes → Replace the Ignition Key.

Perform SKIS VERIFICATION.

No → Test Complete.
NOTE: If this DTC cannot be reset, it could have been an actual theft
attempt.

193
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0516-BATTERY TEMPERATURE SENSOR LOW

When Monitored and Set Condition:

P0516-BATTERY TEMPERATURE SENSOR LOW

When Monitored: Ignition on.
Set Condition: Battery temperature sensor voltage below 0.0392 of a volt for 4.8 seconds.
Three good trips to clear the MIL.

POSSIBLE CAUSES
BATTERY TEMP VOLTS BELOW 0.0392 OF A VOLT
BATTERY TEMPERATURE SENSOR
(K25) BATT TEMP SIGNAL CIRCUIT SHORTED TO GROUND
(K25) BATT TEMP SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt record all DTCs and the related Freeze Frame data.
With DRBIIIt, monitor the Battery Temperature Sensor voltage.
Is the voltage below 0.0392 of a volt?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 2.

2 With the DRBIIIt in sensors, read the Battery Temp Sensor Voltage value. All
Disconnect the Battery Temperature Sensor harness connector.
Did the Batt Temp Sensor voltage change from below 1.0 volt to above 4.5 volts?

Yes → Replace the Battery Temperature Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 3

3 Turn the ignition off. All

Disconnect the C3 PCM harness connector.
Measure the resistance between ground and the (K25) Batt Temp Signal circuit at
the Battery Temp Sensor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (K25) Batt Temp Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 4

194
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0516-BATTERY TEMPERATURE SENSOR LOW — Continued

TEST ACTION APPLICABILITY

4 Measure the resistance between the (K25) Batt Temp Signal circuit and the (K900) All
Sensor ground circuit at the Battery Temp Sensor harness connector.
Is the resistance below 5.0 ohms?

Yes → Repair the short between the (K900) Sensor ground and the (K25)
Batt Temp Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 5

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

195
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0517-BATTERY TEMPERATURE SENSOR HIGH

When Monitored and Set Condition:

P0517-BATTERY TEMPERATURE SENSOR HIGH

When Monitored: Ignition on.
Set Condition: Battery temperature voltage goes above 4.9412 volts for more than 4.8
seconds. Three good trips to clear the MIL.

POSSIBLE CAUSES
BATTERY TEMP SENSOR VOLTAGE ABOVE 4.9412 VOLTS
BATTERY TEMPERATURE SENSOR
(K118) BATT TEMP SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K25) BATT TEMP SIGNAL CIRCUIT OPEN
(K900) SENSOR GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
Record all DTCs and the related Freeze Frame data.
With the DRBIIIt, monitor the Battery Temperature Sensor voltage.
Is the voltage above 4.9412 volts?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 2.

2 Turn the ignition off. All

Disconnect the Battery Temperature Sensor harness connector.
Ignition on, engine not running.
With the DRBIIIt in sensors, read the Battery Temp Voltage value.
Connect a jumper wire between the (K25) Batt Temp Signal circuit and the (K900)
Sensor ground circuit at the Battery Temp Sensor harness connector.
Did the Battery Temp voltage value change from greater than 4.5 volts to less than
1.0 volt?

Yes → Replace the Battery Temperature Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 3

NOTE: Remove the jumper wire before continuing.

196
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0517-BATTERY TEMPERATURE SENSOR HIGH — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C2 and C3 PCM harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (K25) Batt Temp Signal
circuit at the Battery Temp Sensor harness connector.
Does the test light illuminate brightly?

Yes → Repair the short to voltage in the (K118) Batt Temp Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 4

4 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K25) Batt Temp Signal circuit from the Battery Temp
Sensor harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 5

No → Repair the open in the (K25) Batt Temp Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

5 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance in the (K900) Sensor ground circuit from the Sensor
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6
No → Repair the open in the (K900) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

197
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0522-OIL PRESSURE VOLTAGE LOW

When Monitored and Set Condition:

P0522-OIL PRESSURE VOLTAGE LOW

When Monitored: With the ignition on and battery voltage above 10.4 volts.
Set Condition: The switch reads closed at voltage below 0.942 of a volt. The NGC must
see a change in switch state at engine start. One trip fault.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
OIL PRESSURE SWITCH
(G6) OIL PRESSURE SIGNAL CIRCUIT OPEN
(G6) OIL PRESSURE SIGNAL CIRCUIT SHORTED TO VOLTAGE
(G6) OIL PRESSURE SIGNAL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 2.

2 Turn the ignition off. All

Disconnect the Oil Pressure Switch harness connector.
Ignition on, engine not running.
Connect a jumper wire to the (G6) Oil Pressure Signal circuit in the Sensor harness
connector.
With the DRBIIIt monitor the Oil Pressure Switch state.
Touch the other end of the jumper wire to Ground at the Oil Pressure Switch harness
connector several times.
Did the Oil Pressure Switch state change from High to Low?

Yes → Replace the Oil Pressure Switch.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 3
NOTE: Remove the jumper wire before continuing.

198
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0522-OIL PRESSURE VOLTAGE LOW — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C1 PCM harness connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (G6) Oil Pressure Signal
circuit at the Switch harness connector.
Does the 12-volt test light illuminate brightly?

Yes → Repair the short to voltage on the (G6) Oil Pressure Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 4

4 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (G6) Oil Pressure Signal circuit from the Oil Pressure
Switch harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (G6) Oil Pressure Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

5 Measure the resistance between (G6) Oil Pressure Signal circuit and ground at the All
Switch connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (G6) Oil Pressure Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 6

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

199
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0532-A/C PRESSURE SENSOR LOW

When Monitored and Set Condition:

P0532-A/C PRESSURE SENSOR LOW

When Monitored: Engine running, A/C is learned, and the AC Clutch Relay energized.
Set Condition: The A/C pressure sensor signal voltage at the PCM goes below 0.58 of a
volt for 2.6 seconds. One Trip Fault.

POSSIBLE CAUSES
A/C PRESSURE SENSOR VOLTAGE BELOW 0.6 OF A VOLT
(F856) 5-VOLT SUPPLY CIRCUIT OPEN
(F856) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
A/C PRESSURE SENSOR
(C18) A/C PRESSURE SIGNAL CIRCUIT SHORTED TO GROUND
(C18) A/C PRESSURE SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 NOTE: Make sure the A/C refrigerant System is properly charged per the All
Service Information.
Start the engine.
With the DRBIIIt, read the A/C Pressure Sensor voltage.
Is the voltage below 0.6 of a volt?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 2.

2 Turn the ignition off. All

Disconnect the A/C Pressure Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the (F856) 5-volt Supply circuit in the A/C Pressure Sensor
harness connector.
Is the voltage between 4.5 to 5.2 volts?

Yes → Go To 3
No → Go To 6

3 With the DRBIIIt, monitor the A/C Pressure Sensor voltage with the Sensor harness All
connector disconnected.
Is the voltage above 0.6 of a volt?

Yes → Replace the A/C Pressure Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 4

200
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0532-A/C PRESSURE SENSOR LOW — Continued

TEST ACTION APPLICABILITY

4 Turn the ignition off. All
Disconnect the C3 PCM harness connector.
Measure the resistance between ground and the (C18) A/C Pressure Signal circuit in
the A/C Pressure Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (C18) A/C Pressure Signal
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 5

5 Measure the resistance between the (C18) A/C Pressure Signal circuit and the (K900) All
Sensor ground circuit in the A/C Pressure Sensor harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short between the (K900) Sensor ground circuit and
the (C18) A/C Pressure Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 8

6 Turn the ignition off. All

Disconnect the C1 and C3 PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (F856) 5-volt Supply circuit from the A/C Pressure
Sensor harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 7

No → Repair the open in the (F856) 5-volt Supply circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

7 Measure the resistance between ground and the (F855) 5-volt Supply circuit in the All
A/C Pressure Sensor harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (F856) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 8

8 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

201
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0533-A/C PRESSURE SENSOR HIGH

When Monitored and Set Condition:

P0533-A/C PRESSURE SENSOR HIGH

When Monitored: Engine running, A/C is Learned, and the AC Clutch Relay energized.
Set Condition: The A/C pressure sensor signal at the PCM goes above 4.92 volts for 2.6
seconds. One trip Fault.

POSSIBLE CAUSES
A/C PRESSURE SENSOR VOLTAGE ABOVE 4.6 VOLTS
A/C PRESSURE SENSOR
(C18) A/C PRESSURE SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(C18) A/C PRESSURE SIGNAL CIRCUIT OPEN
(C18) A/C PRESSURE SIGNAL CIRCUIT SHORTED TO THE (K856) 5-VOLT SUPPLY
(K900) SENSOR GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 NOTE: Make sure the A/C refrigerant System is properly charged per the All
Service Information.
Start the engine.
With the DRBIIIt, read the A/C Pressure Sensor voltage.
Is the voltage above 4.6 volts?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 2.

2 Turn the ignition off. All

Disconnect the A/C Pressure Sensor harness connector.
Connect a jumper wire between the (C18) A/C Pressure Signal circuit and the (K900)
Sensor ground circuit in the Sensor harness connector.
Ignition on, engine not running.
With the DRBIIIt, monitor the A/C Pressure Sensor voltage.
Is the voltage below 1.0 volt?

Yes → Replace the A/C Pressure Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 3

NOTE: Remove the jumper wire before continuing.

202
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0533-A/C PRESSURE SENSOR HIGH — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C1 and C3 PCM harness connectors.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (C18) A/C Pressure Signal
circuit at the A/C Pressure Sensor harness connector.
Does the test light illuminate brightly?

Yes → Repair the short to voltage in the (C18) A/C Pressure Signal
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 4

4 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (C18) A/C Pressure Signal circuit from the A/C
Pressure Sensor harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 5
No → Repair the open in the (C18) A/C Pressure Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

5 Measure the resistance between the (C18) A/C Pressure Signal circuit and the (K855) All
5-volt Supply circuit in the A/C Pressure Sensor harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the short between the (F856) 5-volt Supply circuit and the
(C18) A/C Pressure Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 6

6 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the A/C Pressure
Sensor harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 7

No → Repair the open in the (K900) Sensor ground circuit

Perform POWERTRAIN VERIFICATION TEST VER - 2.

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

203
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0551-POWER STEERING SWITCH PERFORMANCE

When Monitored and Set Condition:

P0551-POWER STEERING SWITCH PERFORMANCE

When Monitored: With the ignition key on and engine running.
Set Condition: With the vehicle above 40 mph for over 30 seconds, the power steering
pressure switch remains open.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
POWER STEERING PRESSURE SWITCH
(K66) P/S SWITCH SIGNAL CIRCUIT OPEN
(K66) P/S SWITCH SIGNAL CIRCUIT SHORTED TO GROUND
(Z987) GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 2.

2 Turn the ignition off. All

Disconnect the Power Steering Pressure Switch harness connector.
Ignition on, engine not running.
Connect a jumper wire to the (K66) P/S Switch Signal circuit in harness connector.
Using the DRBIIIt, monitor the Power Steering Pressure Switch.
Touch the jumper wire to the (Z987) Ground circuit in the Power Steering Pressure
Switch harness connector several times.
Did the Power Steering Pressure Switch status change from High to Low?
Yes → Replace the Power Steering Pressure Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 3

NOTE: Remove the jumper wire before continuing.

204
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0551-POWER STEERING SWITCH PERFORMANCE — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure resistance of (K66) P/S Switch Signal circuit from the Power Steering
Pressure Switch harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 4

No → Repair the open in the (K66) P/S Switch Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

4 Measure the resistance between ground and the (K66) P/S Pressure Switch Signal All
circuit at the P/S Pressure Switch connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (K66) P/S Switch Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 5

5 Measure the resistance between ground and the (Z987) Ground circuit at the Power All
Steering Pressure Switch connector.
Is the resistance below 5.0 ohms?

Yes → Go To 6
No → Repair the open in the (Z987) Ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

205
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0562-BATTERY VOLTAGE LOW

When Monitored and Set Condition:

P0562-BATTERY VOLTAGE LOW

When Monitored: The engine running. The engine speed greater than 380 RPM.
Set Condition: Battery voltage is 1 volt less than desired system voltage.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
BATTERY POSITIVE CIRCUIT HIGH RESISTANCE
GENERATOR GROUND HIGH RESISTANCE
GENERATOR OPERATION
(K125) GEN FIELD CONTROL CIRCUIT OPEN
(K125) GEN FIELD CONTROL CIRCUIT SHORTED TO GROUND
(Z20) GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 NOTE: Make sure the Battery is in good condition. Using the Midtronics All
Battery Tester, test the Battery before continuing.
NOTE: Inspect the vehicle for after market accessories that may exceed the
Generator System output.
Turn the ignition off.
NOTE: Make sure the generator drive belt is in good operating condition.
NOTE: Inspect the fuses in the PDC. If a fuse is found to be open use the
wiring diagram/schematic as a guide, inspect the wiring and connectors for
damage.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 3.

206
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0562-BATTERY VOLTAGE LOW — Continued

TEST ACTION APPLICABILITY

2 WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A All
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
NOTE: Make sure all wires are clear of the engine’s moving parts.
Start the engine.
Allow the engine to reach normal operating temperature.
Measure the voltage between the Generator B+ Terminal and the Battery + Post.
Is the voltage above 0.4 of a volt?

Yes → Repair the Battery Positive circuit for high resistance between
the Generator and Battery.
Perform POWERTRAIN VERIFICATION TEST VER - 3.

No → Go To 3

3 WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A All

DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: Make sure all wires are clear of the engine’s moving parts.
Measure the voltage between the Generator case and Battery ground post.
Is the voltage above 0.1 of a volt?
Yes → Repair Generator Ground for high resistance, Generator Case to
Battery ground side.
Perform POWERTRAIN VERIFICATION TEST VER - 3.
No → Go To 4

4 Turn the ignition off. All

Disconnect the Generator Field harness connector.
Use a 12-volt test light and jump it across the Generator Field harness connector.
Ignition on, engine not running.
With the DRBIIIt, actuate the Generator Field Control circuit.
Does the test light illuminate brightly and flash on and off?
Yes → Replace the Generator.
Perform POWERTRAIN VERIFICATION TEST VER - 3.
No → Go To 5

5 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K125) Gen Field Control circuit from the Generator
Field harness connector to the appropriate terminal of the special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6

No → Repair the open in the (K125) Gen Field Control circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 3.

207
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0562-BATTERY VOLTAGE LOW — Continued

TEST ACTION APPLICABILITY

6 Measure the resistance between ground and the (K125) Gen Field Control circuit in All
the Generator Field harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (K125) Gen Field Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 3.

No → Go To 7

7 Using a 12-volt test connected to 12-volts, probe the (Z20) Ground circuit in the All
Generator Field harness connector.
Does the test light illuminate brightly?

Yes → Go To 8

No → Repair the open in the (Z20) Ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 3.

8 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 3.

208
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0563-BATTERY VOLTAGE HIGH

When Monitored and Set Condition:

P0563-BATTERY VOLTAGE HIGH

When Monitored: With the ignition on. Engine RPM greater than 1000 RPM. With no
other charging system codes set.
Set Condition: The battery sensed voltage is 1 volt above the charging goal for 13.47
seconds. The PCM senses the battery voltage turns off the field driver and senses the
battery voltage again. If the voltages are the same, the code is set.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
GENERATOR OPERATION
(K125) GEN FIELD CONTROL CIRCUIT SHORTED TO BATTERY VOLTAGE
PCM

TEST ACTION APPLICABILITY

1 NOTE: Make sure the Battery is in good condition. Using the Midtronics All
Battery Tester, test the Battery before continuing.
NOTE: Inspect the vehicle for after market accessories that may exceed the
Generator System output.
Turn the ignition off.
NOTE: Make sure the generator drive belt is in good operating condition.
NOTE: Inspect the fuses in the PDC. If a fuse is found to be open use the
wiring diagram/schematic as a guide, inspect the wiring and connectors for
damage.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 3.

2 Turn the ignition off. All

Disconnect the Generator Field harness connector.
Using a 12-volt test light, jump it across the Generator Field harness connector.
Ignition on, engine not running.
With the DRBIIIt, actuate the Generator Field Control circuit.
Does the test light illuminate brightly and flash on and off?
Yes → Replace the Generator.
Perform POWERTRAIN VERIFICATION TEST VER - 3.

No → Go To 3

209
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0563-BATTERY VOLTAGE HIGH — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C2 PCM harness connector.
Measure the voltage on the (K125) Gen Field Control circuit at the Generator Field
harness connector.
Is the voltage above 1.0 volt?

Yes → Repair the short to voltage in the (K125) Gen Field Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 3.
No → Go To 4

4 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 3.

210
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0572-BRAKE SWITCH NO.1 CIRCUIT LOW

When Monitored and Set Condition:

P0572-BRAKE SWITCH NO.1 CIRCUIT LOW

When Monitored: Ignition on.
Set Condition: When the PCM recognizes Brake Switch #1 is mechanically stuck in the
low/on position. One Trip Fault. Three Global Good Trips to Clear.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
BRAKE LAMP SWITCH OPERATION
(B15) BRAKE SWITCH NO.1 SIGNAL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 NOTE: Verify battery voltage is greater than 10 volts. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 4.

2 Turn the ignition off. All

Remove the Brake Lamp Switch and disconnect the harness connector.
Measure the resistance between the (Z249) Ground circuit terminal and the (B15)
Brake Switch No.1 Signal terminal at the Brake Lamp Switch.
Apply and release the brake pedal plunger while monitoring the ohmmeter.
Does the resistance change from below 5.0 ohms to an open circuit?

Yes → Go To 3
No → Replace the Brake Lamp Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

3 Turn the ignition off. All

Disconnect the C3 PCM harness connector.
Measure the resistance between ground and the (B15) Brake Switch No.1 Signal
circuit in the Brake Lamp Switch harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (B15) Brake Switch No.1 Signal
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 4

211
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0572-BRAKE SWITCH NO.1 CIRCUIT LOW — Continued

TEST ACTION APPLICABILITY

4 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

212
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0573-BRAKE SWITCH NO.1 CIRCUIT HIGH

When Monitored and Set Condition:

P0573-BRAKE SWITCH NO.1 CIRCUIT HIGH

When Monitored: Ignition on.
Set Condition: When the PCM recognizes Brake Switch #1 is stuck in the high/off
position. One Trip Fault. Three good trips to turn off the MIL.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
BRAKE LAMP SWITCH OPERATION
(B15) BRAKE SWITCH NO.1 SIGNAL CIRCUIT OPEN
(Z249) GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 4.

2 Turn the ignition off. All

Disconnect the Brake Lamp Switch harness connector.
Measure the resistance between the Ground circuit terminal and the (B15) Brake
Switch No.1 Signal circuit terminal in the Brake Lamp Switch.
Apply and release the brake pedal while monitoring the ohmmeter.
Does the resistance change from below 5.0 ohms to an open circuit?
Yes → Go To 3

No → Replace the Brake Lamp Switch.

Perform POWERTRAIN VERIFICATION TEST VER - 4.

213
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0573-BRAKE SWITCH NO.1 CIRCUIT HIGH — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (B15) Brake Switch No.1 Signal circuit from the Brake
Lamp Switch harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 4

No → Repair the open in the (B15) Brake Switch No.1 Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

4 Measure the resistance between the (Z249) Ground circuit and ground at the Brake All
Lamp Switch harness connector.
Is the resistance below 5.0 ohms?
Yes → Go To 5
No → Repair the open in the (Z249) Ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

214
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0580-SPEED CONTROL SWITCH NO.1 LOW

When Monitored and Set Condition:

P0580-SPEED CONTROL SWITCH NO.1 LOW

When Monitored: With the ignition key on. Battery voltage above 10 volts.
Set Condition: When switch voltage is less than 0.60 of a volt for 2 minutes.

POSSIBLE CAUSES
SPEED CONTROL SWITCH VOLTAGE LOW
SPEED CONTROL ON/OFF SWITCH
SPEED CONTROL RESUME/ACCEL SWITCH
CLOCKSPRING
(V37) S/C SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
(V37) S/C SIGNAL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 NOTE: Do not press any of the Speed Control Switch buttons. All
Ignition on, engine not running.
With the DRBIIIt, read the Speed Control voltage.
Is the Speed Control voltage below 1.0 volt?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 4.

2 With the DRBIIIt, monitor the Speed Control Switch voltage. All
Disconnect the Speed Control On/Off Switch harness connector.
Did the voltage change to above 4.7 volts?

Yes → Replace the Speed Control On/Off Switch.

Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 3

3 With the DRBIIIt, monitor the Speed Control Switch voltage. All
Disconnect the Speed Control Resume/Accel Switch harness connector.
Did the voltage change to above 4.7 volts?

Yes → Replace the Speed Control Resume/Accel Switch.

Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 4

215
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0580-SPEED CONTROL SWITCH NO.1 LOW — Continued

TEST ACTION APPLICABILITY

4 Turn the ignition off. All
Disconnect the clockspring 6-way harness connector (instrument panel wiring side)
per Service Information.
Ignition on, engine not running.
With the DRBIIIt in Sensors, read the S/C Switch voltage.
Did the S/C Switch volts change to 5.0 volts?

Yes → Replace the Clockspring.

Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 5

5 Turn the ignition off. All

Connect the Clockspring harness connector per Service Information.
Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance between the (K900) Sensor ground circuit and the (V37) S/C
Signal circuit at the Speed Control Switch.
Is the resistance below 5.0 ohms?
Yes → Repair the (V37) S/C Signal circuit shorted to the (K900) Sensor
ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 6

6 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance between ground and the (V37) S/C Signal circuit at the
appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Repair the short to ground in the (V37) S/C Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 7

7 NOTE: Before continuing, disconnect the PCM harness connector and All
check the related wiring terminals for corrosion, damage or terminal push
out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

216
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0581-SPEED CONTROL SWITCH NO.1 HIGH

When Monitored and Set Condition:

P0581-SPEED CONTROL SWITCH NO.1 HIGH

When Monitored: With the ignition key on. Battery voltage above 10 volts.
Set Condition: The PCM detects voltage above 4.8 volts in the Speed Control Switch
Signal circuit. One Trip Fault.

POSSIBLE CAUSES
SPEED CONTROL SWITCH VOLTAGE HIGH
SPEED CONTROL SWITCHES
CLOCKSPRING
(V37) S/C SWITCH SIGNAL CIRCUIT SHORTED TO VOLTAGE
(V37) S/C SWITCH SIGNAL CIRCUIT OPEN BETWEEN PCM AND CLOCKSPRING
(K900) SENSOR GROUND CIRCUIT OPEN BETWEEN PCM AND CLOCKSPRING
(V37) S/C SWITCH SIGNAL CIRCUIT OPEN BETWEEN CLOCKSPRING AND S/C SWITCH
(K900) SENSOR GROUND CIRCUIT OPEN BETWEEN CLOCKSPRING AND S/C SWITCH
PCM

TEST ACTION APPLICABILITY

1 NOTE: Do not press any of the Speed Control Switch buttons. All
Ignition on, engine not running.
With the DRBIIIt, read the Speed Control voltage.
Is the Speed Control voltage above 4.8 volt?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 4.

2 Turn the ignition off. All

Remove the Speed Control Switches from the steering wheel.
Measure the resistance across each Speed Control Switch.
Monitor the ohmmeter while pressing each function button on each switch.
Resume/Accel - 15,400 ohms
Cancel - 909 +/- 9 ohms
Decel (Coast) - 2940 +/- 30 ohms
On/Off - 0 ohms
Set - 6650 +/- 66 ohms
Does the function on the Speed Control Switches have the correct resistance value?
Yes → Go To 3

No → Replace the Speed Control Switch that had the incorrect resis-
tance value.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

217
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0581-SPEED CONTROL SWITCH NO.1 HIGH — Continued

TEST ACTION APPLICABILITY

3 Disconnect the upper and lower 6-way clockspring harness connectors per Service All
Information.
Measure the resistance of the (K900) Sensor ground circuit between the upper and
lower 6-way clockspring harness connectors.
Measure the resistance of the (V37) S/C Switch Signal circuit between the upper and
lower 6-way clockspring harness connectors.
Was the resistance above 5.0 ohms for either circuit?

Yes → Replace the clockspring.

Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 4

4 Connect the Clockspring harness connectors per Service Information. All

Disconnect the Speed Control On/Off Switch 2-way harness connector only.
Ignition on, engine not running.
Measure the voltage on the (V37) S/C Switch Signal circuit in the On/Off Switch
2-way connector.
Is the voltage above 5.2 volts?

Yes → Repair the short to voltage in the (V37) S/C Switch Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 5

5 Turn the ignition off. All

Disconnect the upper and lower Clockspring harness connectors per Service Infor-
mation.
Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (V37) S/C Switch Signal circuit from the lower
Clockspring harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 6

No → Repair the open in the (V37) S/C Switch Signal circuit between
the PCM and Clockspring.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

6 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the lower Clock-
spring harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 7

No → Repair the open (K900) Sensor ground circuit between the PCM
and Clockspring.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

218
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0581-SPEED CONTROL SWITCH NO.1 HIGH — Continued

TEST ACTION APPLICABILITY

7 Measure the resistance of the (V37) S/C Switch Signal circuit from the upper All
Clockspring harness connector to the On/Off switch harness connector.
Is the resistance below 5.0 ohms?

Yes → Go To 8
No → Repair the open in the (V37) S/C Switch Signal circuit, Clock-
spring to S/C Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

8 Measure the resistance of the (K900) Sensor ground circuit from the On/Off Switch All
2-way harness connector to the upper Clockspring harness connector.
Is the resistance below 5.0 ohms?

Yes → Go To 9

No → Repair the open in the (K900) Sensor ground circuit between the
Clockspring and S/C Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

9 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If the there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

219
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0582-SPEED CONTROL VACUUM SOLENOID CIRCUIT

When Monitored and Set Condition:

P0582-SPEED CONTROL VACUUM SOLENOID CIRCUIT

When Monitored: Engine running, the speed control switched on and learned, and the
brake pedal is not pressed. No other fault has occured this trip.
Set Condition: The PCM recognizes an open or short to ground in the speed control
vacuum solenoid control circuit. Cruise will be disabled for the remainder of that key-on
cycle. One Trip fault. Three good trips to clear the MIL.

POSSIBLE CAUSES
SPEED CONTROL SOLENOID OPERATION
(V32) S/C SUPPLY CIRCUIT
SPEED CONTROL VACUUM SOLENOID
(V32) S/C SUPPLY SHORT TO GROUND
(V36) S/C VACUUM SOL CONTROL CIRCUIT SHORTED TO GROUND
(V32) S/C SUPPLY CIRCUIT OPEN
(V36) S/C VACUUM SOL CONTROL CIRCUIT OPEN
(Z901) S/C GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
With the DRBIIIt, actuate the Speed Control Vacuum Solenoid and note operation.
Does the Speed Control Vacuum Solenoid actuate properly?

Yes → Refer to the INTERMITTENT CONDITION symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 2

2 Turn the ignition off. All

Disconnect the S/C Servo harness connector.
Turn the ignition on.
Using the DRBIIIt, actuate the S/C Vacuum Solenoid.
Using a test light connected to ground, probe the (V30) S/C Brake Switch Output
circuit in the S/C Servo harness connector.
Does the test light illuminate brightly and flash on and off?
Yes → Go To 5

No → Go To 3

220
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0582-SPEED CONTROL VACUUM SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the Brake Switch harness connector.
Turn the ignition on.
Using the DRBIIIt, actuate the S/C Vacuum Solenoid.
Using a test light connected to ground, probe the (V32) S/C Supply circuit in the
Brake Switch harness connector.
Does the test light illuminate brightly?

Yes → Go To 4
No → Go To 8

4 Turn the ignition off. All

Disconnect the S/C Servo harness connector.
Measure the resistance of the (Z901) S/C Ground circuit at the S/C Servo harness
connector to ground.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (Z901) S/C Ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

5 Turn the ignition off. All

Disconnect the Speed Control Servo harness connector.
Ignition on, engine not running.
With the DRBIIIt, actuate the Speed Control Vacuum Solenoid.
Using a 12-volt test light connected to battery voltage, probe the S/C Vacuum Control
circuit.
Does the test light illuminate brightly and flash on and off?
Yes → Replace the Speed Control Servo.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 6

6 Turn the ignition off. All

Disconnect the S/C Servo harness connector.
Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (V36) S/C Vacuum Sol Control circuit from the Speed
Control Servo harness connector to the appropriate terminal of special tool # 8815.
Is the resistance below 5.0 ohms?

Yes → Go To 7

No → Repair the open/high resistance in the (V36) S/C Vacuum Sol

Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

221
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0582-SPEED CONTROL VACUUM SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off. All
Disconnect the S/C Servo harness connector.
Disconnect the C3 PCM harness connector.
Measure the resistance between ground and the (V36) S/C Vacuum Solenoid Control
circuit at the Speed Control Servo harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (V36) S/C Vacuum Sol Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 10

8 Turn the ignition off. All

Disconnect the Brake Lamp Switch harness connector.
Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (V32) S/C Supply circuit from the Brake Lamp Switch
harness connector to the appropriate terminal of special tool # 8815.
Is the resistance below 5.0 ohms?
Yes → Go To 9
No → Repair the open/high resistance in the (V32) S/C Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

9 Turn the ignition off. All

Disconnect the Brake Switch harness connector.
Disconnect the C3 PCM harness connector.
Measure the resistance between ground and the (V32) S/C Supply circuit at the
Speed Control Servo harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (V32) S/C Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 10

10 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
If the there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

222
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0586-SPEED CONTROL VENT SOLENOID CIRCUIT

When Monitored and Set Condition:

P0586-SPEED CONTROL VENT SOLENOID CIRCUIT

When Monitored: Engine running, the speed control switched on and learned, and the
brake pedal is not pressed. No other fault has occured this trip.
Set Condition: The PCM detects an open or short to ground in the Speed Control Vent
Control circuit. Cruise will be disabled for the remainder of that key-on cycle. One Trip
Fault. Three good trips to clear the MIL.

POSSIBLE CAUSES
SPEED CONTROL SOLENOID OPERATION
(V32) S/C SUPPLY CIRCUIT
SPEED CONTROL VENT SOLENOID
(V32) S/C SUPPLY SHORT TO GROUND
(V35) S/C VENT SOL CONTROL CIRCUIT OPEN
(V35) S/C VENT SOL CONTROL CIRCUIT SHORTED TO GROUND
(V32) S/C SUPPLY CIRCUIT OPEN
(Z901) S/C GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
With the DRBIIIt, actuate the Speed Control Vent Solenoid and note operation.
Does the Speed Control Vent Solenoid acutate properly?

Yes → Refer to the INTERMITTENT CONDITION symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 2

2 Turn the ignition off. All

Disconnect the S/C Servo harness connector.
Turn the ignition on.
Using the DRBIIIt, actuate the S/C Vent Solenoid.
Using a test light connected to ground, probe the (V30) S/C Brake Switch Output
circuit in the S/C Servo harness connector.
Does the test light illuminate brightly and flash on and off?
Yes → Go To 5

No → Go To 3

223
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0586-SPEED CONTROL VENT SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the Brake Switch harness connector.
Turn the ignition on.
Using the DRBIIIt, actuate the S/C Vent Solenoid.
Using a test light connected to ground, probe the (V32) S/C Supply circuit in the
Brake Switch harness connector.
Does the test light illuminate brightly and flash on and off?

Yes → Go To 4
No → Go To 8

4 Turn the ignition off. All

Disconnect the S/C Servo harness connector.
Measure the resistance of the (Z901) S/C Ground circuit at the S/C Servo harness
connector to ground.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (Z901) S/C Ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

5 Turn the ignition off. All

Disconnect the Speed Control Servo harness connector.
Ignition on, engine not running.
With the DRBIIIt, actuate the Speed Control Vent Solenoid.
Using a 12-volt test light connected to battery voltage, probe the (V35) Speed Control
Vent Solenoid Control circuit in the Speed Control Servo harness connector.
Does the test light illuminate brightly and flash on and off?
Yes → Replace the Speed Control Servo.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 6

6 Turn the ignition off. All

Disconnect the S/C Servo harness connector.
Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (V35) S/C Vent Sol Control circuit from the Speed
Control Servo harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 7

No → Repair the open/high resistance in the (V35) S/C Vent Sol Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

224
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0586-SPEED CONTROL VENT SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off. All
Disconnect the S/C Servo harness connector.
Disconnect the C3 PCM harness connector.
Measure the resistance between ground and the (V35) S/C Vent Sol Control circuit at
the Speed Control Servo harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (V35) Speed Control Vent
Solenoid Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 10

8 Turn the ignition off. All

Disconnect the Brake Lamp Switch harness connector.
Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (V32) S/C Supply circuit from the Brake Lamp Switch
harness connector to the appropriate terminal of special tool # 8815.
Is the resistance below 5.0 ohms?
Yes → Go To 9
No → Repair the open/high resistance in the (V32) S/C Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

9 Turn the ignition off. All

Disconnect the Brake Switch harness connector.
Disconnect the C3 PCM harness connector.
Measure the resistance between ground and the (V32) S/C Supply circuit at the
Speed Control Servo harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (V32) S/C Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 10

10 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
If the there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

225
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0594-SPEED CONTROL SERVO POWER CIRCUIT

When Monitored and Set Condition:

P0594-SPEED CONTROL SERVO POWER CIRCUIT

When Monitored: Engine running, the speed control switched on and learned, and the
brake pedal is not pressed. No other fault has occured this trip.
Set Condition: The speed control power supply circuit is either open or shorted to ground.
Cruise will be disabled for the remainder of that key-on cycle. One Trip Fault. Three good
trips to clear the MIL.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
(V32) S/C SUPPLY CIRCUIT OPEN
(V32) S/C SUPPLY CIRCUIT SHORTED TO GROUND
BRAKE LAMP SWITCH
(V30) S/C BRAKE SWITCH OUTPUT
(V30) S/C BRAKE SWITCH OUPUT CIRCUIT OPEN
(V30) S/C BRAKE SWITCH OUTPUT CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 4.

2 Disconnect the Brake Lamp Switch harness connector. All

Start the engine.
Using a 12-volt test light connected to ground, probe the (V32) S/C Supply circuit in
the Switch harness connector while holding the Cruise Switch in the ON position.
Does the test light illuminate brightly?

Yes → Go To 3

No → Go To 7

226
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0594-SPEED CONTROL SERVO POWER CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect and remove the Brake Lamp Switch.
Measure the resistance across the (V32) S/C Supply circuit terminal and the (V30)
S/C Brake Switch Output circuit terminal at the Brake Lamp Switch.
Push the Plunger of the Switch in and let it out.
Does the resistance change from below 5.0 ohms to an open circuit?

Yes → Go To 4

No → Replace the Brake Lamp Switch.

Perform POWERTRAIN VERIFICATION TEST VER - 4.

4 Turn the ignition off. All

Connect the Brake Lamp Switch harness connecter and install the Switch.
Disconnect the Speed Control Servo harness connector.
Ignition on, engine not running.
NOTE: It is necessary to PRESS and HOLD the Speed Control Switch in the
ON position while checking for voltage.
Using a 12-volt test light connected to ground, probe the (V30) S/C Brake Switch
Output circuit in the Servo Harness connector.
Does the test light illuminate brightly?
Yes → Replace the S/C Servo.
Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 5

5 Turn the ignition off. All

Disconnect the Brake Lamp Switch harness connector.
Measure the resistance of the (V30) S/C Brake Switch Output circuit from the Brake
Lamp Switch harness connector to the S/C Servo harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the excessive resistance in the (V30) S/C Brake Switch
Output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 6

6 Measure the resistance between ground and the (V30) S/C Brake Switch Output All
circuit at the Speed Control Servo harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (V30) S/C Brake Switch Output
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 9

227
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0594-SPEED CONTROL SERVO POWER CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off. All
Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (V32) S/C Supply circuit from the Brake Lamp Switch
harness connector to the appropriate terminal of special tool #8815.
Is the resistance above 5.0 ohms?

Yes → Repair the open in the (V32) S/C Supply circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 8

8 Measure the resistance between ground and the (V32) S/C Supply circuit in the All
Brake Switch harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (V32) S/C Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 9

9 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

228
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom List:
P0600-SERIAL COMMUNICATION LINK
P0601-INTERNAL MEMORY CHECKSUM INVALID

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P0600-SERIAL COMMUNICA-
TION LINK.

When Monitored and Set Condition:

P0600-SERIAL COMMUNICATION LINK

When Monitored: With the ignition on.
Set Condition: Internal Bus communication failure between processors.

P0601-INTERNAL MEMORY CHECKSUM INVALID

When Monitored: With the ignition on.
Set Condition: Internal checksum for software failed, does not match calculated value.

POSSIBLE CAUSES
PCM INTERNAL OR SPI

TEST ACTION APPLICABILITY

1 The Powertrain Control Module is reporting internal errors, view repair to continue. All
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

229
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0622-GENERATOR FIELD CONTROL CIRCUIT

When Monitored and Set Condition:

P0622-GENERATOR FIELD CONTROL CIRCUIT

When Monitored: With the ignition on. Engine speed greater than 1000 RPM. Battery
voltage greater than 10.4 volts. ASD sense switch is on.
Set Condition: When the PCM tries to regulate the generator field with no result during
monitoring.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
GENERATOR OPERATION
(K125) GEN FIELD CONTROL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K125) GEN FIELD CONTROL CIRCUIT OPEN
(K125) GEN FIELD CONTROL CIRCUIT SHORTED TO GROUND
(Z20) GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 3.

2 Turn the ignition off. All

Disconnect the Generator Field harness connector.
Jump a 12-volt test light across the Generator Field harness connector.
Ignition on, engine not running.
With the DRBIIIt, actuate the Generator Field Control circuit.
Does the test light illuminate brightly and flash on and off?

Yes → Replace the Generator.

Perform POWERTRAIN VERIFICATION TEST VER - 3.

No → Go To 3

230
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0622-GENERATOR FIELD CONTROL CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the C2 PCM harness connector.
Ignition on, engine not running.
Measure the voltage on the (K125) Gen Field Control circuit in the Generator Field
harness connector.
Is the voltage above 1.0 volt?

Yes → Repair the short to voltage in the (K125) Gen Field Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 3.
No → Go To 4

4 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K125) Gen Field Control circuit from the Generator
Field harness connector to the appropriate terminal of the special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 5
No → Repair the open in the (K125) Gen Field Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 3.

5 Measure the resistance between ground and (K125) Gen Field Control circuit in the All
Generator Field harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (K125) Gen Field Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 3.
No → Go To 6

6 Using a 12-volt test connected to battery voltage, probe the (Z20) Ground circuit in All
the Generator Field harness connector.
Does the test light illuminate brightly?
Yes → Go To 7

No → Repair the open in the (Z20) Ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 3.

7 NOTE: Before continuing, check the PCM connector terminals for corro- All
sion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 3.

231
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0627-FUEL PUMP RELAY CIRCUIT

When Monitored and Set Condition:

P0627-FUEL PUMP RELAY CIRCUIT

When Monitored: With the ignition on. Battery voltage greater than 10.4 volts.
Set Condition: An open or shorted condition is detected in the fuel pump relay control
circuit.

POSSIBLE CAUSES
FUEL PUMP RELAY OPERATION
(F1) FUSED IGNITION SWITCH OUTPUT CIRCUIT
(A930) FUSED B+ CIRCUIT
FUEL PUMP RELAY
(K31) FUEL PUMP RELAY CONTROL CIRCUIT OPEN
(K31) FUEL PUMP RELAY CONTROL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, actuate the Fuel Pump Relay.
Is the Fuel Pump Relay operating?
Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 2

2 Turn the ignition off. All

Remove the Fuel Pump Relay from the PDC.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (F1) Fused Ignition Switch
Output circuit in the PDC.
Does the test light illuminate brightly?

Yes → Go To 3
No → Repair the (F1) Fused Ignition Switch Output circuit. Inspect the
related fuse. An open fuse may have been caused by a short to
ground.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

232
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0627-FUEL PUMP RELAY CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Using a 12-volt test light connected to ground, probe the (A930) Fused B+ circuit of
the fuel pump relay in the PDC.
Does the test light illuminate brightly?
Yes → Go To 4

No → Repair the open or short to ground in the (A930) Fused B+ circuit.

Inspect and replace any open fuses.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Measure the resistance of the Fuel Pump Relay Coil. All

Is the resistance between 70 to 90 ohms?

Yes → Go To 5

No → Replace the Fuel Pump Relay.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Disconnect the C3 PCM harness connector. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K31) Fuel Pump Relay Control circuit from the PDC
to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 6
No → Repair the open in the (K31) Fuel Pump Relay Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Measure the resistance between ground and the (K31) Fuel Pump Relay Control All
circuit in the PDC.
Is the resistance below 5.0 ohms?
Yes → Repair the short to ground in the (K31) Fuel Pump Relay Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 7

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

233
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0630-VIN NOT PROGRAMMED IN PCM

When Monitored and Set Condition:

P0630-VIN NOT PROGRAMMED IN PCM

When Monitored: Ignition on.
Set Condition: The VIN has not been programmed into the PCM.

POSSIBLE CAUSES
PROGRAMMING VIN INTO PCM
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, erase DTCs.
Using the DRBIIIt, program VIN into the PCM.
Start the engine.
NOTE: If the engine will not start, crank the engine over for 15 seconds.
Crank at least 2 times with the ignition switch returning to the off position
each time.
Allow the engine to reach normal operating temperature.
With the DRBIIIt, read DTCs.
Does the DTC reset?
Yes → Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → The VIN has been succcessfully programmed into the PCM. Test
is complete.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

234
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0632-ODOMETER NOT PROGRAMMED IN PCM

When Monitored and Set Condition:

P0632-ODOMETER NOT PROGRAMMED IN PCM

When Monitored: Ignition on.
Set Condition: Odometer is not programed into the PCM.

POSSIBLE CAUSES
PROGRAMMING MILEAGE INTO PCM
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, erase DTCs.
Using the DRBIIIt, program the mileage into the PCM.
Start the engine.
Allow the engine to reach normal operating temperature.
With the DRBIIIt, read DTCs.
Does the DTC reset?
Yes → Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → The mileage has been succcessfully programmed into the PCM.

Test is complete.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

235
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0633-SKIM KEY NOT PROGRAMMED IN PCM

When Monitored and Set Condition:

P0633-SKIM KEY NOT PROGRAMMED IN PCM

When Monitored: Ignition on.
Set Condition: The SKIM Key information has not been programmed into the PCM.

POSSIBLE CAUSES
PROGRAMMING SKIM KEY INTO PCM
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, erase DTCs.
Using the DRBIIIt, program the SKIM Key information into the PCM.
Start the engine.
NOTE: If the engine will not start, crank the engine over for 15 seconds.
Crank at least 2 times with the ignition switch returning to the off position
each time.
Allow the engine to reach normal operating temperature.
With the DRBIIIt, read DTCs.
Does the DTC reset?
Yes → Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → The SKIM KEY information has been succcessfully programmed
into the PCM. Test is complete.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

236
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0645-A/C CLUTCH RELAY CIRCUIT

When Monitored and Set Condition:

P0645-A/C CLUTCH RELAY CIRCUIT

When Monitored: With the ignition on. Battery voltage greater than 10 volts. A/C Switch
on.
Set Condition: An open or shorted condition is detected in the A/C clutch relay control
circuit. The desired A/C state does not equal the actual A/C clutch relay state. Three good
trips to clear the MIL.

POSSIBLE CAUSES
A/C CLUTCH RELAY OPERATION
(F960) FUSED IGNITION SWITCH OUTPUT CIRCUIT
(A926) FUSED B+ CIRCUIT
A/C CLUTCH RELAY
(C13) A/C CLUTCH RELAY CONTROL CIRCUIT OPEN
(C13) A/C CLUTCH RELAY CONTROL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, actuate the A/C Clutch Relay.
Is the A/C Clutch Relay operating?
Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 2

2 Turn the ignition off. All

Remove the A/C Clutch Relay from the PDC.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (F960) Fused Ignition
Switch Output circuit.
Does the test light illuminate brightly?

Yes → Go To 3
No → Repair the open or short to ground in the (F960) Fused Ignition
Switch Output circuit. Inspect and replace any open fuses.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

237
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0645-A/C CLUTCH RELAY CIRCUIT — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Using a 12-volt test light connected to ground, probe the (A926) Fused B+ circuit of
the fuel pump relay in the PDC.
Does the test light illuminate brightly?
Yes → Go To 4

No → Repair the open or short to ground in the (A926) Fused B+ circuit.

Inspect and replace any open fuses.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

4 Turn the ignition off. All

Measure the resistance of the A/C Clutch Relay Coil.
Is the resistance between 60 to 80 ohms?

Yes → Go To 5
No → Replace the A/C Clutch Relay.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

5 Disconnect the C3 PCM harness connector. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (C13) A/C Clutch Relay Control circuit from the PDC
to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 6
No → Repair the open in the (C13) A/C Clutch Relay Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

6 Measure the resistance between ground and the (C13) A/C Clutch Relay Control All
circuit in the PDC.
Is the resistance below 5.0 ohms?

Yes → Repair the short to ground in the (C13) A/C Clutch Relay Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 7

7 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

238
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0685-ASD RELAY CONTROL CIRCUIT

When Monitored and Set Condition:

P0685-ASD RELAY CONTROL CIRCUIT

When Monitored: With ignition on. Battery voltage above 10 volts.
Set Condition: An open or shorted condition is detected in the ASD relay control circuit
for more than 2.7 seconds. ASD Relay state does not equal the desired state. P0688 will set
along with P0685.

POSSIBLE CAUSES
ASD RELAY OPERATION
(A209) FUSED B+ CIRCUITS
ASD RELAY
(K342) ASD RELAY CONTROL CIRCUIT OPEN
(K342) ASD RELAY CONTROL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, actuate the ASD Relay.
Is the ASD Relay operating?
Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 2

2 Turn the ignition off. All

Remove the ASD Relay from the PDC.
Using a 12-volt test light connect to ground, probe the (A209) Fused B+ circuits in the
PDC.
Does the test light illuminate brightly?
Yes → Go To 3

No → Repair the open or short to ground in the (A209) Fused B+

circuits. Inspect and replace any open fuses.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

3 Measure the resistance of the ASD Relay Coil. All

Is the resistance between 60 to 80 ohms?

Yes → Go To 4
No → Replace the ASD Relay.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

239
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0685-ASD RELAY CONTROL CIRCUIT — Continued

TEST ACTION APPLICABILITY

4 Disconnect the C3 PCM harness connector. All
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K342) ASD Relay Control circuit from the PDC to the
appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 5
No → Repair the open in the (K342) ASD Relay Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Measure the resistance between ground and the (K342) ASD Relay Control circuit in All
the PDC.
Is the resistance below 5.0 ohms?
Yes → Repair the short to ground in the (K342) ASD Relay Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 6

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

240
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0688-ASD RELAY SENSE CIRCUIT LOW

When Monitored and Set Condition:

P0688-ASD RELAY SENSE CIRCUIT LOW

When Monitored: With ignition key on. Battery voltage greater than 10 volts.
Set Condition: No voltage sensed at the PCM when the ASD relay is energized for 3.075
seconds. Three good trips to clear the MIL.

POSSIBLE CAUSES
VERIFY ASD DTC
ASD RELAY
(A209) FUSED B+ CIRCUITS
(K334) ASD RELAY OUTPUT CIRCUIT OPEN (NO START)
(K334) ASD RELAY OUTPUT CIRCUIT SHORTED TO GROUND
(K334) ASD RELAY OUTPUT CIRCUIT OPEN (START)
PCM

TEST ACTION APPLICABILITY

1 NOTE: Diagnose P0685 - Auto Shutdown Relay Control Circuit first if set All
along with this DTC.
With the DRBIIIt, erase the DTC.
Attempt to start the engine. If the engine will not start, crank the engine for at least
15 seconds. It may be necessary to repeat several times.
Does the DTC reset?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Attempt to start the engine. All

Does the engine start?

Yes → Go To 3

No → Go To 4

241
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0688-ASD RELAY SENSE CIRCUIT LOW — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Remove the ASD Relay from the PDC.
Disconnect the C3 PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K334) ASD Relay Output circuit from the PDC to the
appropriate terminals of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 8

No → Repair the open in the (K334) ASD Relay Output circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Turn the ignition off. All

Install a substitute relay in place of the ASD Relay.
Ignition on, engine not running.
With the DRBIIIt, erase DTCs.
Attempt to start the engine.
With the DRBIIIt, read DTCs.
Does the DTC reset?
Yes → Go To 5
No → Replace the ASD Relay.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 Turn the ignition off. All

Remove the ASD Relay from the PDC.
Using a 12-volt test light connect to ground, probe the (A209) Fused B+ circuits in the
PDC.
Does the test light illuminate brightly?

Yes → Go To 6
No → Repair the open or short to ground in the (A209) Fused B+
circuits. Inspect the related fuse and repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Disconnect the C3 PCM harness connector. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K334) ASD Relay Output circuit from the PDC to the
appropriate terminals of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Go To 7

No → Repair the open in the (K334) ASD Relay Output circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

242
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P0688-ASD RELAY SENSE CIRCUIT LOW — Continued

TEST ACTION APPLICABILITY

7 Measure the resistance between ground and the (K334) ASD Relay Output circuit at All
the Relay connection.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (K334) ASD Relay Output
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 8

8 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

243
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P0700-TRANSMISSION CONTROL SYSTEM (MIL REQUEST)

When Monitored and Set Condition:

P0700-TRANSMISSION CONTROL SYSTEM (MIL REQUEST)

When Monitored: Ignition on.
Set Condition: An active DTC is stored in the TCM.
TEST ACTION APPLICABILITY
1 This is an informational DTC letting you know that a DTC(s) is stored in the All
Transmission Control Module.
Erase this DTC from the PCM after all Transmission DTC(s) have been repaired.
Using the DRBIIIt, read the Transmission Controller DTC and refer to the
Transmission Category and perform the appropriate symptom.
PCM Diagnostic Information complete.

Continue
Test Complete.

244
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P0850-PARK/NEUTRAL SWITCH PERFORMANCE

When Monitored and Set Condition:

P0850-PARK/NEUTRAL SWITCH PERFORMANCE

When Monitored: Continuously with the transmission in Park, Neutral, or Drive and
NOT in Limp-in mode.
Set Condition: This code will set if the PCM detects an incorrect Park/Neutral switch
state for a given mode of vehicle operation.

POSSIBLE CAUSES
DRB DISPLAYS P/N & D/R NOT IN CORRECT POSITION
TRS T41 SENSE (P/N SENSE) CIRCUIT OPEN
TRS T41 SENSE (P/N SENSE) CIRCUIT SHORTED TO GROUND
TRANSMISSION RANGE SENSOR
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the Park/Neutral Position Switch input state.
While moving the gear selector through all gear positions (Park to 1 and back to
Park), monitor the DRB display.
Did the DRB display show P/N and D/R in the correct gear positions?
Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 2

2 Turn the ignition off. All

Disconnect the C4 PCM harness connector.
Disconnect the Transmission Range Sensor harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the TRS T41 Sense (P/N Sense) circuit from the TRS
harness connector to the appropriate terminal of special tool #8815 installed.
Is the resistance below 5.0 ohms?

Yes → Go To 3

No → Repair the open in the TRS T41 Sense (P/N Sense) circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

245
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P0850-PARK/NEUTRAL SWITCH PERFORMANCE — Continued

TEST ACTION APPLICABILITY

3 Measure the resistance between ground and the TRS T41 Sense (P/N Sense) circuit All
at the TRS harness connector.
Is the resistance above 100k ohms?

Yes → Go To 4
No → Repair the short to ground in the TRS T41 Sense (P/N Sense)
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

4 Connect the Transmission Range Sensor harness connector. All

Move the Gear selector through all gear positions, from Park to 1st and back.
While moving the gear selector through each gear, measure the resistance between
ground and the TRS T41 Sense (P/N Sense) circuit using special tool #8815.
NOTE: The circuit is grounded in Park and Neutral and open in the other
positions.
Did the resistance change from above 100 kohms (open) to below 10.0 ohms
(grounded)?

Yes → Go To 5
No → Replace the Transmission Range Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

5 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

246
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P1115-GENERAL TEMPERATURE SENSOR PERFORMANCE

When Monitored and Set Condition:

P1115-GENERAL TEMPERATURE SENSOR PERFORMANCE

When Monitored: With the ignition on and engine running.
Set Condition: The PCM compares the ouputs of the ECT, IAT, and Ambient Temp
sensors. If one sensor does not corralate with the other two sensors the fault is set.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
TEMPERATURE SENSOR CIRCUT
FAULTY SENSOR
EXCESSIVE RESISTANCE IN THE SENSOR SIGNAL CIRCUIT
EXCESSIVE RESISTANCE IN THE (K900) SENSOR GROUND CIRCUIT
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the DTCs and record the related Freeze Frame data.
NOTE: All ECT, Intake Air, and Ambient Air Temperature Sensor codes must
be diagnosed and repaired before continuing.
Is the Good Trip Counter displayed and equal to zero
Yes → Go To 2
No → Refer to the INTERMITENT CONDITION Symptom (Diagnostic
Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 With the DRBIIIt in Sensors, read the ECT, Ambient/Battery Temp, and Intake Air All
Temp Sensor temp values.
Start the engine.
Allow the engine to reach normal operating temperature while monitoring the three
Sensor temperature values.
Is the temperature for each of the Sensors increasing properly?
Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 3

247
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P1115-GENERAL TEMPERATURE SENSOR PERFORMANCE — Continued

TEST ACTION APPLICABILITY

3 Ignition on, engine not running. All
Disconnect the suspected faulty sensor.
Connect a jumper wire between the Sensor Signal circuit and the (K900) Sensor
ground circuit.
With the DRBIIIt in Sensors, read the voltage of the suspected Sensor.
Did the voltage reading start at 4.8 to 5.0 volts and decrease to 0 volts?

Yes → Replace the faulty Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Turn the ignition off. All

Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the Sensor Signal circuit from the Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance above 5.0 ohms.
Yes → Repair the excessive resistance in the Sensor Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance above 5.0 ohms.

Yes → Repair the excessive resistance in the (K900) Sensor ground

circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 6

6 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, review repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

248
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
P1593-SPEED CONTROL SWITCH NO.1 STUCK

When Monitored and Set Condition:

P1593-SPEED CONTROL SWITCH NO.1 STUCK

When Monitored: Ignition on.
Set Condition: S/C Switche #1 is mechanically stuck in the On/Off, Resume/Accel, or Set
position for too long. One trip fault.

POSSIBLE CAUSES
SPEED CONTROL SWITCH STATUS
SPEED CONTROL SWITCHES
(V37) S/C SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
(V37) S/C SIGNAL CIRCUIT SHORTED TO GROUND
(V37) S/C SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
(V37) S/C SIGNAL CIRCUIT OPEN
(K900) SENSOR GROUND CIRCUIT OPEN
PCM

TEST ACTION APPLICABILITY

1 Start the engine. All
With the DRBIIIt, monitor each switch function for the Speed Control Switches.
Press and release each Speed Control Button.
- Resume/Accel
- Cancel
- Decel (Coast)
- On/Off
- Set
Does each switch function change status when pressing and then depressing each
switch?

Yes → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 2

249
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P1593-SPEED CONTROL SWITCH NO.1 STUCK — Continued

TEST ACTION APPLICABILITY

2 Turn the ignition off. All
Remove the Speed Control Switches from the steering wheel.
Measure the resistance across each Switch Control Switch.
Monitor the ohmmeter while pressing each function button on each switch.
Resume/Accel - 15,400 ohms
Cancel - 909 +/- 9 ohms
Decel (Coast) - 2940 +/- 30 ohms
On/Off - 0 ohms
Set - 6650 +/- 66 ohms
Does the function on the Speed Control Switches have the correct resistance value?

Yes → Go To 3

No → Replace the Speed Control Switch that had the incorrect resis-
tance value.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

3 Disconnect the C3 PCM harness connector. All

Ignition on, engine not running.
Measure the voltage on the (V37) S/C Signal circuit at the Speed Control harness
connector.
Is the is the voltage above 5.0 volts?
Yes → Repair the short to battery voltage in the (V37) S/C Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 4

4 Turn the ignition off. All

NOTE: The measurement must be taken from both Speed Control Switch
harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (V37) S/C Signal circuit from the Speed Control
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms for both measurement?
Yes → Go To 5

No → Repair the open in the (V37) S/C Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 4.

5 Measure the resistance between ground and the (V37) S/C Signal circuit at the Speed All
Control harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (V37) S/C Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No → Go To 6

250
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P1593-SPEED CONTROL SWITCH NO.1 STUCK — Continued

TEST ACTION APPLICABILITY

6 Disconnect the C2 and C3 PCM harness connectors. All
Measure the resistance between the (V37) S/C Signal circuit and the (K900) Sensor
ground circuit in the Speed Control harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the short between the (V37) S/C Signal circuit and the
(K900) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 4.
No → Go To 7

7 NOTE: The measurement must be taken from both Speed Control Switch All
harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the Speed Control
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms for both measurements?
Yes → Go To 8

No → Repair the open in the (K900) Sensor ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 4.

8 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

251
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom List:
P1603-PCM INTERNAL DUAL-PORT RAM COMMUNICATION
P1604-PCM INTERNAL DUAL-PORT RAM READ/WRITE INTEG-
RITY FAILURE
P1607-PCM INTERNAL SHUTDOWN TIMER RATIONALITY

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P1603-PCM INTERNAL DUAL-
PORT RAM COMMUNICATION.

When Monitored and Set Condition:

P1603-PCM INTERNAL DUAL-PORT RAM COMMUNICATION

When Monitored: Ignition off, on, and run/start.
Set Condition: Internal PCM failure detected. Intermittent open on PCM Connector 1,
pin 12, (F11) Fused Ignition Switch Output circuit.

P1604-PCM INTERNAL DUAL-PORT RAM READ/WRITE INTEGRITY FAILURE

When Monitored: Ignition off, on, and run/start.
Set Condition: Internal PCM failure detected. Intermittent open on PCM Connector 1,
pin 12, (F11) Fused Ignition Switch Output circuit.

P1607-PCM INTERNAL SHUTDOWN TIMER RATIONALITY

When Monitored: Ignition on.
Set Condition: Internal PCM failure detected.

POSSIBLE CAUSES
PCM FUSED IGNITION SWITCH OUTPUT CIRCUIT
PCM

252
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P1603-PCM INTERNAL DUAL-PORT RAM COMMUNICATION — Continued

TEST ACTION APPLICABILITY

1 Turn the ignition off. All
Disconnect the C1 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
With a 12-volt test light connected to ground and with special tool #8815 installed,
probe the (F1), (F26) Fused Ignition Switch Output circuits.
Perform the above check with the Ignition key in the off lock position, Ignition on,
engine not running position, and during cranking.
Wiggle the related wire harness while probing the special tool with the test light to
try to interrupt the circuit.
Does the test light illuminate brightly?

Yes → Go To 2
No → Repair the open or excessive resistance in the (F11) Fused
Ignition Switch (Off, Run, Start) circuit. Inspect the related fuse,
if the fuse is open check the circuit for a short to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
The Powertrain Control Module is reporting internal errors, view repair to continue.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

253
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom List:
P1696-PCM FAILURE EEPROM WRITE DENIED
P1697-PCM FAILURE SRI MILES NOT STORED

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P1696-PCM FAILURE EEPROM
WRITE DENIED.

When Monitored and Set Condition:

P1696-PCM FAILURE EEPROM WRITE DENIED

When Monitored: Ignition key on, Continuous.
Set Condition: An attempt to program/write to the internal EEPROM failed, Also checks
at powerdown.

P1697-PCM FAILURE SRI MILES NOT STORED

When Monitored: Ignition key on, Continuous.
Set Condition: An attempt to program/write to the internal EEPROM failed, Also checks
at powerdown.

POSSIBLE CAUSES
DRB DISPLAYS WRITE FAILURE
DRB DISPLAYS WRITE REFUSED 2ND TIME
DRB DISPLAYS SRI MILEAGE INVALID
COMPARE SRI MILEAGE WITH ODOMETER

TEST ACTION APPLICABILITY

1 With the DRBIIIt, perform the SRI Memory Test. All
Does the DRBIIIt display Write Failure?

Yes → Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Go To 2

2 With the DRBIIIt, perform the SRI Memory Test. All

Does the DRBIIIt display Write Refused?

Yes → Go To 3

No → Go To 4

254
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P1696-PCM FAILURE EEPROM WRITE DENIED — Continued

TEST ACTION APPLICABILITY

3 With the DRBIIIt, perform the SRI Memory Test a third time. All
NOTE: Retest the SRI Memory two more times.
Does the DRBIIIt display Write Refused again?

Yes → Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Test Complete.

4 With the DRBIIIt, perform the SRI Memory Test. All

Does the DRBIIIt display SRI Mileage Invalid?

Yes → Update the mileage and retest the SRI Memory.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Go To 5

5 Compare the SRI Mileage stored with the Instrument Panel Odometer. All
Is the mileage within the specified range displayed on the DRBIIIt?

Yes → Test Complete.

No → Update the mileage and retest the SRI Memory.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

255
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom List:
P2096-DOWN STREAM FUEL TRIM LEAN BANK 1
P2097-DOWN STREAM FUEL TRIM RICH BANK 1
P2098-DOWN STREAM FUEL TRIM LEAN BANK 2
P2099-DOWN STREAM FUEL TRIM RICH BANK 2

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P2096-DOWN STREAM FUEL
TRIM LEAN BANK 1.

When Monitored and Set Condition:

P2096-DOWN STREAM FUEL TRIM LEAN BANK 1

When Monitored: With the engine running in closed loop mode, the ambient/battery
temperature above (-7°C)20°F, altitude below 8500 ft and fuel level greater than 15%.
Set Condition: If the PCM multiplies short term compensation by long term adaptive and
a certain percentage is exceeded for two trips, a freeze frame is stored, the MIL illuminates
and a trouble code is stored. Two Trip Fault. Three good trips to turn off the MIL.

P2097-DOWN STREAM FUEL TRIM RICH BANK 1

When Monitored: With the engine running in closed loop mode, the ambient/battery
temperature above (-7°C)20°F and altitude below 8500 ft.
Set Condition: If the PCM multiplies short term compensation by long term adaptive as
well as a purge fuel multiplier and the result is below a certain value for 30 seconds over
two trips, a freeze frame is stored, the MIL illuminates and a trouble code is stored. Two
Trip Fault. Three good trips to turn off the MIL.

P2098-DOWN STREAM FUEL TRIM LEAN BANK 2

When Monitored: With the engine running in closed loop mode, the ambient/battery
temperature above (-7°C)20°F, altitude below 8500 ft and fuel level greater than 15%.
Set Condition: If the PCM multiplies short term compensation by long term adaptive and
a certain percentage is exceeded for two trips, a freeze frame is stored, the MIL illuminates
and a trouble code is stored. Two Trip Fault. Three good trips to turn off the MIL.

P2099-DOWN STREAM FUEL TRIM RICH BANK 2

When Monitored: With the engine running in closed loop mode, the ambient/battery
temperature above (-7°C)20°F and altitude below 8500 ft.
Set Condition: If the PCM multiplies short term compensation by long term adaptive as
well as a purge fuel multiplier and the result is below a certain value for 30 seconds over
two trips, a freeze frame is stored, the MIL illuminates and a trouble code is stored. Two
Trip Fault. Three good trips to turn off the MIL.

256
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P2096-DOWN STREAM FUEL TRIM LEAN BANK 1 — Continued

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
EXHAUST LEAK
ENGINE MECHANICAL PROBLEM
O2 SENSOR
O2 SIGNAL CIRCUIT
O2 RETURN CIRCUIT
FUEL CONTAMINATION

TEST ACTION APPLICABILITY

1 NOTE: Check the vehicle repair history. If the O2 has been replace ensure All
that the O2 sensor was properly installed and meets OEM specification.
NOTE: Check for contaminants that may have damaged the O2 Sensor:
contaminated fuel, unapproved silicone, oil and coolant.
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

WARNING: To avoid personal injury from the exhaust system being hot,
allow the exhaust to cool down to a safe temperature before performing a
physical inspection.
Visually and Physically inspect the for holes, cracks and blockage in the exhaust
system.
Is the exhaust system is good condition?

Yes → Go To 3
No → Repair or Replace as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

257
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P2096-DOWN STREAM FUEL TRIM LEAN BANK 1 — Continued

TEST ACTION APPLICABILITY

3 Check for any of the following conditions/mechanical problems. All
AIR INDUCTION SYSTEM - must be free from leaks.
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions or leaks.
ENGINE PCV SYSTEM - must flow freely
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to
correct injector
Are there any engine mechanical problems?

Yes → Repair as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 Ignition on, engine not running. All

Disconnect the O2 Sensor harness connector.
With the DRBIIIt, monitor the O2 Sensor voltage.
The O2 Sensor voltage should read 5.0 volts on the DRBIIIt with the connector
disconnected.
Using a jumper wire, jump the O2 Signal circuit to the O2 Return circuit in the O2
Sensor harness connector.
NOTE: The voltage should drop from 5.0 volts to 2.5 volts with the jumper
wire in place.
Did the O2 Sensor volts change from 5.0 volts to 2.5 volts?

Yes → Replace the O2 Sensor

Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 5

5 Remove the jump wire. All

Ignition on, engine not running.
With the DRBIIIt, monitor the O2 Sensor voltage.
Is the voltage above 4.8 volts?

Yes → Go To 6
No → Check the O2 Signal circuit for a short to ground, open, or short
to voltage. Inspect the O2 Sensor connector and the PCM harness
connector. If OK, replace and program the Powertrain Control
Module in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Measure the voltage on the O2 Return circuit in the O2 Sensor harness connector. All
Is the voltage at 2.5 volts?
Yes → Check the fuel system for contaminants.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Check the O2 Return circuit for a short to ground, open, or short

to voltage. Inspect the O2 Sensor connector and the PCM harness
connector. If OK, replace and program the Powertrain Control
Module in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

258
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom List:
P2302-IGNITION COIL NO.1 SECONDARY CIRCUIT- INSUFFI-
CIENT IONIZATION
P2305-IGNITION COIL NO.2 SECONDARY CIRCUIT- INSUFFI-
CIENT IONIZATION
P2308-IGNITION COIL NO.3 SECONDARY CIRCUIT- INSUFFI-
CIENT IONIZATION

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P2302-IGNITION COIL NO.1
SECONDARY CIRCUIT- INSUFFICIENT IONIZATION.

When Monitored and Set Condition:

P2302-IGNITION COIL NO.1 SECONDARY CIRCUIT- INSUFFICIENT IONIZA-

TION
When Monitored: Engine running and battery voltage greater than 10 volts.
Set Condition: If PCM detects that the secondary ignition burn time is incorrect or not
present an error is detected. One Trip Fault. Three good trips to turn off the MIL.

P2305-IGNITION COIL NO.2 SECONDARY CIRCUIT- INSUFFICIENT IONIZA-

TION
When Monitored: Engine running and battery voltage greater than 10 volts.
Set Condition: If PCM detects that the secondary ignition burn time is incorrect or not
present an error is detected. One Trip Fault. Three good trips to turn off the MIL.

P2308-IGNITION COIL NO.3 SECONDARY CIRCUIT- INSUFFICIENT IONIZA-

TION
When Monitored: Engine running and battery voltage greater than 10 volts.
Set Condition: If PCM detects that the secondary ignition burn time is incorrect, to short,
or not present, an error is detected. One Trip Fault. Three good trips to turn off the MIL.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
(K334) ASD RELAY OUTPUT CIRCUIT
COIL RAIL RESISTANCE
IGNITION COIL
IGNITION COIL DRIVER CIRCUIT OPEN
IGNITION COIL DRIVER CIRCUIT SHORTED TO GROUND
PCM

259
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P2302-IGNITION COIL NO.1 SECONDARY CIRCUIT- INSUFFICIENT

IONIZATION — Continued
TEST ACTION APPLICABILITY
1 Check for any related TSBs. All
Ignition on, engine not running.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2 Turn the ignition off. All

Disconnect the coil rail harness connector.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Relay.
Using a 12-volt test light connected to ground, check the (K334) ASD Relay Output
circuit at the coil rail harness connector.
Does the test light illuminate brightly?
Yes → Go To 3
No → Repair the excessive resistance or short to ground in the (K334
ASD Relay Output circuit. Inspect the related fuse and repair as
necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
Stop All Actuations

3 Turn the ignition off. All

Disconnect the coil rail harness connector.
Note: The following resistance measurement should be taken at 70-80
degrees F.
NOTE: The resistance of the 2.4L Primary Ignition Coil is 0.53 to 0.63 of an
ohm and the resistance of a 4.0L Primary Coil Rail is 0.51 to 0.61 of an ohm
at 70°F (21.1°C).
Measure the resistance of the Primary Coil Rail.
Is the resistance value within the noted specification for the coil being tested?
Yes → Go To 4

No → Replace the coil rail.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

4 Turn the ignition off. All

Disconnect the Ignition Coil Rail harness connector.
Using a 12-volt test light connected to a 12-volt source, probe the Ignition Coil Driver
circuit.
Crank the engine for 5 seconds while observing the test light.
Does the test light blink/flicker?

Brightly blinking or flickering.

Replace the Ignition Coil Rail.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
ON constantly.
Go To 5
OFF constantly.
Go To 6

260
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P2302-IGNITION COIL NO.1 SECONDARY CIRCUIT- INSUFFICIENT

IONIZATION — Continued
TEST ACTION APPLICABILITY
5 Turn the ignition off. All
Disconnect the C2 PCM harness connector.
Measure the resistance between the Ignition Coil Driver circuit and ground.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the Ignition Coil Driver circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Note: Before continuing, check the PCM harness connector ter-

minals for corrosion, damage, or terminal push out. Repair as
necessary. Replace and program the Powertrain Control Module
in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Turn the ignition off. All

Disconnect the C2 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the Ignition Coil Driver circuit from the Coil Rail harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes → Note: Before continuing, check the PCM harness connector ter-
minals for corrosion, damage, or terminal push out. Repair as
necessary. Replace and program the Powertrain Control Module
in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Repair the open in the Ignition Coil Driver circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

261
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
P2503-CHARGING SYSTEM OUTPUT LOW

When Monitored and Set Condition:

P2503-CHARGING SYSTEM OUTPUT LOW

When Monitored: The engine running. The engine speed greater than 1157 RPM.
Set Condition: The battery sensed voltage is 1 volt below the charging goal for 13.47
seconds. The PCM senses the battery voltage turns off the field driver and senses the
battery voltage again. If the voltages are the same, the code is set.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
BATTERY POSITIVE CIRCUIT HIGH RESISTANCE
CASE GROUND HIGH RESISTANCE
GENERATOR OPERATION
(Z20) GEN GROUND CIRCUIT OPEN
(K125) GEN FIELD CONTROL CIRCUIT SHORTED TO BATTERY VOLTAGE
(K125) GEN FIELD CONTROL CIRCUIT OPEN
(K125) GEN FIELD CONTROL CIRCUIT SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 NOTE: Inspect the vehicle for aftermarket accessories that may exceed the All
Generator System output.
Ignition on, engine not running.
NOTE: The battery must be fully charged.
NOTE: The Generator belt tension and condition must be checked before
continuing.
With the DRBIIIt, read DTCs and record the related Freeze Frame data.
With the DRBIIIt, erase DTCs.
Start the engine.
Allow the idle to stabilize.
Ignition on, engine not running.
With the DRBIIIt, read DTCs.
Is the Good Trip Counter displayed and equal to zero?

Yes → Go To 2

No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 3.

262
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

P2503-CHARGING SYSTEM OUTPUT LOW — Continued

TEST ACTION APPLICABILITY

2 WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A All
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: Ensure all wires are clear of the engine’s moving parts.
Start the engine.
Warm the engine to operating temperature.
Measure the voltage between the Generator B+ Output Terminal and the Battery+
Post.
Is the voltage above 0.4 of a volt?

Yes → Repair the high resistance in the Battery Positive circuit between
the Generator and Battery.
Perform POWERTRAIN VERIFICATION TEST VER - 3.

No → Go To 3

3 WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A All

DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: Make sure all wires are clear of the engine’s moving parts.
Measure the voltage between the Generator Case and Battery ground post.
Is the voltage above 0.1 of a volt?
Yes → Repair high resistance in the Generator Case Ground.
Perform POWERTRAIN VERIFICATION TEST VER - 3.
No → Go To 4

4 Turn the ignition off. All

Disconnect the Generator Field harness connector.
Using a 12-volt test light, jump it across the Generator Field harness connector.
Ignition on, engine not running.
With the DRBIIIt, actuate the Generator Field Driver circuit.
Does the test light illuminate brightly and flash on and off?

Yes → Replace the Generator.

Perform POWERTRAIN VERIFICATION TEST VER - 3.

No → Go To 5

5 Turn the ignition off. All

Using a 12-volt test connected to battery voltage, probe the (Z20) Generator Ground
circuit in the Generator Field harness connector.
Does the test light illuminate brightly?

Yes → Go To 6

No → Repair the open in the (Z20) Generator Ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 3.

6 Disconnect the C3 PCM harness connector. All

Ignition on, engine not running.
Measure the voltage on the (K125) Gen Field Control circuit at the Generator Field
harness connector.
Is the voltage above 1.0 volt?

Yes → Repair the short to voltage in the (K125) Gen Field Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 3.
No → Go To 7

263
bY dR.dEaDhEaD
DRIVEABILITY - NGC

P2503-CHARGING SYSTEM OUTPUT LOW — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off. All
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K125) Gen Field Control circuit from the Generator
Field harness connector to the appropriate terminal of the special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 8
No → Repair the open in the (K125) Gen Field Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 3.

8 Measure the resistance between ground and the (K125) Gen Field Control circuit in All
the Generator Field harness connector.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (K125) Gen Field Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 3.
No → Go To 9

9 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 3.

264
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
U0101-NO BUS MESSAGE FROM TRANS CONTROL MODULE

When Monitored and Set Condition:

U0101-NO BUS MESSAGE FROM TRANS CONTROL MODULE

When Monitored: Equipped with automatic transmission. The ignition on. Battery
voltage greater than 10 volts.
Set Condition: An open circuit on the (F11) Fused Igniton Switch Output circuit. No bus
messages from the TCM for 20 seconds, two trips required.

POSSIBLE CAUSES
DTC RESET
PCM FUSED IGNITION SWITCH OUTPUT CIRCUIT
PCI BUS UNABLE TO COMMUNICATE WITH DRBIIIt
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, erase DTCs.
Cycle the ignition key on and off several times. Leaving the ignition on for at least 20
seconds.
With the DRBIIIt, read DTCs.
Does the DTC reset?
Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2 Turn the ignition off. All

Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
With a 12-volt test light connected to ground and with special tool #8815 installed,
probe the (F11) Fused Ignition Switch Output circuit.
Perform the above check with the Ignition key in the off lock position, Ignition on,
engine not running position, and during cranking.
Wiggle the related wire harness while probing the special tool with the test light to
try to interrupt the circuit.
Does the test light illuminate brightly?
Yes → Go To 3

No → Repair the open or excessive resistance in the (F11) Fused

Ignition Switch (Offf, Run, Start) circuit. Inspect the related fuse,
if the fuse is open check the circuit for a short to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

265
bY dR.dEaDhEaD
DRIVEABILITY - NGC

U0101-NO BUS MESSAGE FROM TRANS CONTROL MODULE — Continued

TEST ACTION APPLICABILITY

3 NOTE: Determine which modules this vehicle is equipped with before All
beginning.
NOTE: When attempting to communicate with any of the modules on this
vehicle, the DRBIIIt will display 1 of 2 different communication errors: a
NO RESPONSE message or a BUS +/- SIGNALS OPEN MESSAGE.
Ignition on, engine not running.
Use the DRBIIIt, attempt to communicate with the remaining control modules.
Was the DRBIIIt able to communicate with one or more of the Modules?

Yes → Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Refer to the COMMUNICATION category and perform the PCI

BUS COMMUNICATION FAILURE Symptom.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

266
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

Symptom:
U0155-NO CLUSTER BUS MESSAGE

When Monitored and Set Condition:

U0155-NO CLUSTER BUS MESSAGE

When Monitored: Ignition key on and engine running.
Set Condition: No messages received from the MIC (Instrument Cluster) for 20 seconds.

POSSIBLE CAUSES
DTC RESET
COMMUNICATE WITH CLUSTER
INSTRUMENT CLUSTER OPERATION
PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, erase DTCs.
Start the engine and shut if off several times allowing it to idle each time for 20
seconds.
With the DRBIIIt, read DTCs.
Does the DTC reset?

Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2 Ignition on, engine not running. All

With the DRBIIIt, attempt to communicate with the Instrument cluster.
Can communication be established with the Instrument Cluster?

Yes → Go To 3
No → Refer to the Communication Category and perform the appropri-
ate symptom related to no communication with cluster.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

3 Start the engine All

Allow the engine to idle.
Is the correct engine speed display in the instrument cluster (Tach)?

Yes → Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Refer to the Instrument Category and perform the appropriate

symptom.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

267
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
U0168-NO SKIM BUS MESSAGE

When Monitored and Set Condition:

U0168-NO SKIM BUS MESSAGE

When Monitored: Ignition on or engine running.
Set Condition: No J1850 messages received from the Smart Key Immobilizer Module
(SKIM) for 20 seconds. One Trip Fault. Three good trips to turn off the MIL.

POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
NO RESPONSE FROM SKIM
PCI BUS CIRCUIT OPEN FROM PCM TO SKIM
SKIM/PCM

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read the DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
Yes → Go To 2
No → Refer to the INTERMITTENT CONDITION Symptom (Diagnos-
tic Procedure).
Perform SKIS VERIFICATION.

2 With the DRBIIIt, attempt to communicate with the SKIM. All

NOTE: This test will indicate if the bus is operational from the DLC to the
SKIM.
Was the DRBIIIt able to communicate with the SKIM?

Yes → Go To 3

No → Refer to Symptom BUS +/- SIGNAL OPEN FROM SKIM in the

COMMUNICATION category.
Perform SKIS VERIFICATION.

268
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

U0168-NO SKIM BUS MESSAGE — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
Disconnect the PCM harness connectors.
Disconnect the SKIM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the PCI Bus circuit from the SKIM harness connector to
the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

Yes → Go To 4

No → Repair the open in the PCI Bus circuit between the PCM and the
SKIM.
Perform SKIS VERIFICATION.

4 Connect the PCM harness connectors. All

Replace the Sentry Key Immobilizer Module in accordance with the Service Infor-
mation.
Ignition on, engine not running.
Display and erase all PCM and SKIM DTCs.
Perform 5 ignition key cycles leaving the ignition key on for 90 seconds per cycle.
With the DRB, display PCM DTCs.
Does the DRB display the same DTC?
Yes → Replace and program the Powertrain Control Moldule per service
Information.
Perform SKIS VERIFICATION.

No → Test Complete.

269
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
*CHECKING A/C SYSTEM OPERATION WITH NO DTCS

POSSIBLE CAUSES
CHECK FOR PCM DTCS
REFRIGERATION SYSTEM NOT PROPERLY CHARGED
HIGH PRESS CUT-OFF SWITCH
LOW PRESSURE SWITCH
POWERTRAIN CONTROL MODULE
A/C CLUTCH COIL
A/C COMPRESSOR CLUTCH GROUND CIRCUIT OPEN
(C3) A/C CLUTCH RELAY OUTPUT CIRCUIT OPEN
A/C REQUEST CIRCUIT OPEN
(A17) FUSED B+ CIRCUIT OPEN
A/C CLUTCH RELAY
A/C - HEATER CONTROL MODULE
BODY CONTROL MODULE
A/C ON/OFF CONTROL CIRCUIT OPEN
A/C ON/OFF CONTROL CIRCUIT OPEN

TEST ACTION APPLICABILITY

1 With the DRBIIIt, check for PCM DTCs. All
Are any DTCs present?

Yes → Return to the symptom list and choose the symptom(s).

Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 2

2 Turn the ignition off. All

Verify that the Refrigerant System is properly charged per Service Procedure.
Is the Refrigerant System properly charged?
Yes → Go To 3

No → Properly charge the Refrigerant System per Service Information.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

3 Verify the High Pressure Cut-Off Switch operation per Service Information. All
Is the High Pressure Cut-Off Switch OK?

Yes → Go To 4

No → Replace the High Pressure Cut-Off Switch.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

270
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

*CHECKING A/C SYSTEM OPERATION WITH NO DTCS — Continued

TEST ACTION APPLICABILITY

4 Verify the Low Pressure Switch operation per Service Information. All
Is the Low Pressure Switch OK?

Yes → Go To 5
No → Replace the Low Pressure Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

5 Ignition on, engine not running. All

Position the Mode switch on the A/C - Heater Control Module to the Panel position.
With the DRBIIIt in BCM, select Inputs/Outputs.
Monitor the A/C Select Switch state while pressing the A/C mode switch on and off.
Does the A/C Select Switch state change accordingly.

Yes → Go To 6

No → Go To 13

6 Position the Mode switch on the A/C - Heater Control Module to the Panel position. All
With the DRBIIIt in Powertrain, select Engine and select Inputs/Outputs.
Monitor the A/C Select Switch state while pressing the A/C mode switch on and off.
Does the A/C Select Switch state change accordingly.
Yes → Go To 7

No → Replace and program the Powertrain Control Module per Service

Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

7 Connect a test light between the ground circuit and the A/C Clutch Relay Output All
circuit.
With the DRBIIIt, actuate the A/C Clutch Relay.
Does the test light illuminate brightly on and off with the relay actuation?
Yes → Replace the A/C Clutch Coil.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 8

8 Turn the ignition off. All

Disconnect the A/C Clutch harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the A/C Compressor Clutch ground
circuit in the A/C Clutch harness connector.
Is the resistance below 5.0 ohms?
Yes → Go To 9

No → Repair the open in the A/C Compressor Clutch ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

9 Turn the ignition off. All

Remove the A/C Clutch Relay.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the (C3) A/C Clutch Relay Output circuit between the
Relay and the A/C Clutch Coil.
Is the resistance below 5.0 ohms?

Yes → Go To 10

No → Repair the open in the (C3) A/C Clutch Relay Output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

271
bY dR.dEaDhEaD
DRIVEABILITY - NGC

*CHECKING A/C SYSTEM OPERATION WITH NO DTCS — Continued

TEST ACTION APPLICABILITY

10 Engine Running. All
Turn the A/C system on and the fan on high.
With the DRBIIIt in Inputs/Outputs, read the A/C request state.
Does the A/C request state change?
Yes → Go To 11

No → Repair the open in the A/C Request circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

11 Turn the ignition off. All

Remove the A/C Clutch Relay.
Note: Check connectors - Clean/repair as necessary.
Measure the voltage of the (A17) Fused B+ circuit at the A/C Clutch Relay connector.
Is the voltage above 11.0 volts?

Yes → Go To 12

No → Repair the open in the (A17) Fused B+ circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

12 If there are no possible causes remaining, view repair. All

Repair
Replace the A/C Clutch Relay.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

13 Turn the ignition off. All

Disconnect the A/C - Heater Control C1 harness connector.
Ignition on, engine not running.
Measure the voltage between the A/C On/Off Control circuit and ground.
Is the voltage greater than 11.0 volts?
Yes → Go To 14
No → Go To 15

14 Turn the ignition off. All

Disconnect the A/C - Heater Control C1 harness connector.
Ignition on, engine not running.
With the DRBIIIt in BCM, select Inputs/Outputs.
Monitor the A/C Select Switch state while connecting a jumper wire between ground
and the A/C On/Off Control circuit in the A/C - Heater Control C1 harness connector.
Does the A/C Select Switch state change from 9Off9 to 9On9 when the jumper wire is
connected.

Yes → Replace the A/C - Heater Control Module in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No → Replace and program the Body Control Module per Service
Information.
Perform BODY VERIFICATION TEST - VER 1.

272
bY dR.dEaDhEaD
 DRIVEABILITY - NGC

*CHECKING A/C SYSTEM OPERATION WITH NO DTCS — Continued

TEST ACTION APPLICABILITY

15 Turn the ignition off. All
Disconnect the BCM C1 harness connector.
Disconnect the A/C - Heater Control C1 harness connector.
Measure the resistance of the A/C On/Off Control circuit between the BCM C1
harness connector and the A/C - Heater Control C1 harness connector.
Is the resistance below 5.0 ohms?

Yes → Replace and program the Body Control Module per Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
No → Repair the A/C On/Off Control Circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

273
bY dR.dEaDhEaD
DRIVEABILITY - NGC

Symptom:
*CHECKING PCM POWERS AND GROUNDS

POSSIBLE CAUSES
(A209) PCM FUSED B+ CIRCUIT
(F1) AND (F26) PCM FUSED IGNITION SWITCH OUTPUT CIRCUITS
(Z130) (Z131) PCM GROUND CIRCUITS

TEST ACTION APPLICABILITY

1 Turn the ignition off. All
Disconnect the C1 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Using a 12-volt test light connected to ground, probe the (A209) PCM Fused B+
circuit in the appropriate terminal of special tool #8815.
Does the test light illuminate brightly?
Yes → Go To 2

No → Repair the open in the (A209) Fused B+ circuit. Inspect the

related fuses and repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2 CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING All

THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (F1) and (F26) PCM Fused
Ignition Switch Output (Off, Run, Start) circuits in the appropriate terminals of
special tool #8815.
Does the test light illuminate brightly?
Yes → Go To 3

No → Repair the open in the (F1) or (F26) Fused Ignition Switch Output
(Off, Run, Start) circuit(s). Inspect the related fuses and and
repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

3 Turn the ignition off. All

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Using a 12-volt test light connected to battery voltage, probe the (Z130) and (Z131)
PCM Ground circuits in the appropriate terminals of special tool #8815.
Does the test light illuminate brightly?

Yes → Test Complete.

No → Repair the open in the (Z130) and (Z131) PCM Ground circuit(s).
Perform POWERTRAIN VERIFICATION TEST VER - 1.

274
bY dR.dEaDhEaD
 STARTING

Symptom:
*CHECKING FUEL DELIVERY

POSSIBLE CAUSES
FUEL PUMP RELAY
FUEL PRESSURE OUT OF SPECIFICATION
RESTRICTED FUEL SUPPLY LINE
FUEL PUMP INLET STRAINER PLUGGED
FUEL PUMP
(A61) FUSED B+ CIRCUIT
(A141) FUEL PUMP RELAY OUTPUT CIRCUIT OPEN
(Z1) FUEL PUMP GROUND CIRCUIT EXCESSIVE RESISTANCE
FUEL PUMP MODULE

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, actuate the ASD Fuel System test.
Note: It may be necessary to use a mechanics stethoscope in the next step.
Listen for fuel pump operation at the fuel tank.
Does the Fuel Pump operate?
Yes → Go To 2
No → Go To 5

Caution: Stop All Actuations.

2 Turn the ignition off. All

WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Install a fuel pressure gauge to the fuel rail test port.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Fuel System test and observe the fuel pressure
gauge.
NOTE: Fuel pressure specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Choose a conclusion that best matches your fuel pressure reading.
Below Specification
Go To 3

Within Specification
Test Complete.

Above Specification
Replace the fuel filter/fuel pressure regulator.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

Caution: Stop All Actuations.

275
bY dR.dEaDhEaD
STARTING

*CHECKING FUEL DELIVERY — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Raise vehicle on hoist, and disconnect the fuel pressure line at the fuel pump module.
Install special 5/169 fuel line adapter tool #6539 between disconnected fuel line and
the fuel pump module.
Attach a fuel pressure test gauge to the 9T9 fitting on tool #6539.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Fuel System test and observe the fuel pressure
gauge.
NOTE: Fuel pressure specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Is the fuel pressure within specification now?

Yes → Repair/replace fuel supply line as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Go To 4
Caution: Stop All Actuations.

4 Turn the ignition off. All

WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose,fitting or line,
the fuel system pressure must be released.
Remove the Fuel Pump Module and inspect the Fuel Inlet Strainer.
Is the Fuel Inlet Strainer plugged?
Yes → Replace the Fuel Pump Inlet Strainer.
Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Replace the Fuel Pump Module.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

5 Turn the ignition off. All

Disconnect the fuel pump module harness connector.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Fuel System test.
Using a 12-volt test light connected to ground, probe the (A141) Fuel Pump Relay
Output circuit at the Fuel Pump Module harness connector.
Does the test light illuminate brightly?
Yes → Go To 6

No → Go To 8
Caution: Stop All Actuations.

6 Turn the ignition off. All

Disconnect the Fuel Pump Module harness connector.
Using a test light connected to 12-volts, backprobe the (Z1) Fuel Pump ground circuit
at the Fuel Pump Module harness connector.
Does the test light illuminate brightly?

Yes → Go To 7

No → Repair the excessive resistance in the (Z1) Fuel Pump Ground

circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

276
bY dR.dEaDhEaD
 STARTING

*CHECKING FUEL DELIVERY — Continued

TEST ACTION APPLICABILITY

7 If there are no possible causes remaining, view repair. All

Repair
Replace the Fuel Pump Module.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

8 Turn the ignition off. All

Remove the Fuel Pump Relay from the PDC.
Using a 12-volt test light connected to ground, backprobe the Fuel Pump Relay Fused
B+ circuit at the PDC.
Does the test light illuminate?
Yes → Go To 9

No → Repair the open or short to ground in the (A61) Fuel Pump Realy
Fused B+ circuit. Inspect the fuse and repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

9 Disconnect the Fuel Pump Module harness connector. All

Measure the resistance of the (A141) Fuel Pump Relay Output circuit from the relay
connector to the Fuel Pump Module connector.
Is the resistance below 5.0 ohms?
Yes → Replace the Fuel Pump Relay.
Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Repair the open in the (A141) Fuel Pump Relay Output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

277
bY dR.dEaDhEaD
STARTING

Symptom:
*CHECKING HARD START (FUEL DELIVERY SYSTEM)

POSSIBLE CAUSES
RESTRICTED FUEL SUPPLY LINE
FUEL PUMP MODULE
FUEL PUMP INLET STRAINER PLUGGED
FAULTY FUEL PUMP MODULE
FUEL INJECTORS
FUEL CONTAMINATION

TEST ACTION APPLICABILITY

1 Turn the ignition off. All
WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Install the fuel pressure gauge at the engine. Refer to the Service Information FUEL
DELIVERY Section.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Fuel System test and observe the fuel pressure
gauge.
NOTE: Fuel pressure specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Choose a conclusion that best matches your fuel pressure reading.

Below Specification
Go To 2
Within Specification
Go To 4

2 Turn the ignition off. All

WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Raise vehicle on hoist, and disconnect the fuel supply line at the fuel pump module.
Install special tool #6539 (5/169) fuel line adapter fuel pressure gauge between the
fuel supply line and the fuel pump module.
Ignition on, engine not running.
With the DRBIIIt, actuate the ASD Fuel System test and observe the fuel pressure
gauge.
NOTE: Fuel pressure specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Is the fuel pressure within specification?

Yes → Visually and physically inspect the fuel supply lines between the
fuel tank and the fuel rail. Repair/replace as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 3

278
bY dR.dEaDhEaD
 STARTING

*CHECKING HARD START (FUEL DELIVERY SYSTEM) — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off. All
WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose,fitting or line,
the fuel system pressure must be released.
Remove the Fuel Pump Module and inspect the Fuel Inlet Strainer.
Is the Fuel Inlet Strainer plugged?

Yes → Replace the Fuel Pump Inlet Strainer.

Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Test Complete.

4 NOTE: Before continuing visually and physically inspect the fuel delivery All
system for external leaks or damage. Repair /replace as necessary.
Turn the ignition off.
WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Install special tool #6539 (5/169) fuel line adapter.
Install the fuel pressure gauge.
Start the engine and allow the fuel system to reach maximum pressure.
Turn the ignition off.
NOTE: Fuel specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Using special tool #C4390, Hose Clamp Pliers, pinch the rubber fuel line between the
fuel pressure gauge and the engine.
Monitor the fuel pressure gauge for a minimum of 5 minutes.
NOTE: The pressure should not fall below 241 KPa (35 psi)
Does the fuel pressure drop?
Yes → Replace fuel pump module.
Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Go To 5

5 WARNING: The fuel system is under a constant pressure even with the All
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Remove special tool #C4390.
Start the engine and allow the fuel system to reach maximum pressure.
Turn the ignition off.
NOTE: Fuel specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Install special tool #C4390, Hose Clamp Pliers, pinch the rubber fuel line between the
fuel pressure gauge and the fuel pump module.
Monitor the fuel pressure gauge for a minimum of 5 minutes.
NOTE: The pressure should not fall below 241 KPa (35 psi)
Does the fuel pressure drop?
Yes → Replace leaking fuel injectors.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Check the fuel for contaminants.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

279
bY dR.dEaDhEaD
STARTING

Symptom:
*ENGINE CRANKS DOES NOT START

POSSIBLE CAUSES
NO START PRE-TEST
POWERTRAIN FUSES OPEN
SECONDARY INDICATORS PRESENT
NO CKP SENSOR SIGNAL WHEN CRANKING ENGINE
NO CMP SENSOR SIGNAL WHEN CRANKING ENGINE
ENGINE MECHANICAL PROBLEM
(A142) ASD RELAY OUTPUT CIRCUIT OPEN
FUEL CONTAMINATION

TEST ACTION APPLICABILITY

1 Note: The following list of items must be checked before continuing with All
any no start tests.
The battery must be fully charged and in good condition. A low charged battery may
produce invalid test results. If the battery is low, charge the battery and then attempt
to start the vehicle by cranking the engine for 15 seconds, 3 consecutive times.
This will allow any DTCs to set that may have been erased due to a dead battery.
Try to communicate with PCM, if not able to communicate check fuses.
Make sure the Powers and Ground to the PCM are ok.
Make sure the PCM communicates with the DRBIIIt and that there are no DTCs
stored in the PCM memory. If the PCM reports a No Response condition, refer to the
Communication category for the proper tests.
Read the PCM DTCs with the DRBIIIt. If any DTCs are present, they must be
repaired before continuing with any other No Start diagnostic tests. Refer to the
Symptom list for the related P-code that is reported by the PCM.
Make sure that the PCI bus is functional. Attempt to communicate with the
Instrument Cluster and VTSS. If you are unable to establish communicate refer to
the Communication category for the proper symptoms.
The Sentry Key Immobilizer System must be operating properly. Check for proper
communication with the DRBIIIt and check for DTCs that may be stored in the
Sentry Key Immobilizer Module (SKIM). Repair the DTC(s) before continuing.
If no DTCs are found, using the DRBIIIt, select Clear PCM (BATT Disconnect).
Crank the engine several times. Using the DRBIIIt, read DTCs. If a DTC is present
perform the DTC diagnostics before continuing.
Were any problems found?

Yes → Repair as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 2

2 Check for any open fuses in the PDC or Junction Block that may be related to the No All
Start condition.
Are any of the fuses open?

Yes → Replace the open fuse and check the related circuit(s) for a short
to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 3

280
bY dR.dEaDhEaD
 STARTING

*ENGINE CRANKS DOES NOT START — Continued

TEST ACTION APPLICABILITY

3 Ignition on, engine not running. All
With the DRBIIIt, under DTCs & Related Functions, read the Secondary Indicators
while cranking the engine.
Are there any Secondary Indicators present while cranking the engine?
Yes → Refer to symptom list and perform tests related to the secondary
indicator that is reported by the DRBIIIt.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No → Go To 4

4 With the DRBIIIt in Sensors, check the Current CKP Count while cranking the All
engine.
Does the CKP Counter change while cranking the engine?

Yes → Go To 5
No → Refer to Driveability Symptom P0320-NO CRANK REFERENCE
SIGNAL AT PCM.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

5 With the DRBIIIt in Sensors, check the Current CMP Count while cranking the All
engine.
Does the Current CMP Count change while cranking the engine?
Yes → Go To 6

No → Refer to Driveability Symptom P0340-NO CAM SIGNAL AT PCM

Perform POWERTRAIN VERIFICATION TEST VER - 5.

6 Check for any of the following conditions/mechanical problems. All

ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions or leaks.
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to
correct injector
Are there any engine mechanical problems?
Yes → Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No → Go To 7

7 Turn the ignition off. All

Remove the ASD relay from the PDC.
Disconnect the PCM harness connectors.
Verify the ASD Relay is getting Fused B+ voltage before continuing.
Measure the resistance of the (A142) ASD Relay output circuit from the ASD Relay
connector to the PCM harness connector, Ignition coil, and the fuel injectors.
Is the resistance below 5.0 ohms?

Yes → Go To 8

No → Repair the open ASD Relay output circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

281
bY dR.dEaDhEaD
STARTING

*ENGINE CRANKS DOES NOT START — Continued

TEST ACTION APPLICABILITY

8 Verify that the Fuel tank is not empty before continuing. All
Follow the diagnostics for Checking Fuel Delivery under the Driveability section of
this manual.
Was the No Start condition solved after following the above diagnostic procedure?
Yes → Test Complete.

No → Check for contamination/water in the fuel. Ensure the fuel being

used in this vehicle meets manufactures Fuel Requirement, refer
to the service manual.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

282
bY dR.dEaDhEaD
 STARTING

Symptom:
*FUEL PRESSURE LEAK DOWN

POSSIBLE CAUSES
CHECKING FUEL LEAK DOWN
FUEL INJECTORS

TEST ACTION APPLICABILITY

1 NOTE: Before continuing visually and physically inspect the fuel delivery All
system for external leaks or damage. Repair /replace as necessary.
Turn the ignition off.
WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Install special tool #6539 (5/169) fuel line adapter.
Install the fuel pressure gauge.
Start the engine and allow the fuel system to reach maximum pressure.
Turn the ignition off.
NOTE: Fuel specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Using special tool #C4390, Hose Clamp Pliers, pinch the rubber fuel line between the
fuel pressure gauge and the engine.
Monitor the fuel pressure gauge for a minimum of 5 minutes.
NOTE: The pressure should not fall below 241 KPa (35 psi).
Does the fuel pressure drop?
Yes → Replace the fuel pump module.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No → Go To 2

2 WARNING: The fuel system is under a constant pressure even with the All
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Remove special tool #C4390.
Start the engine and allow the fuel system to reach maximum pressure.
Turn the ignition off.
NOTE: Fuel specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Install special tool #C4390, Hose Clamp Pliers, pinch the rubber fuel line between the
fuel pressure gauge and the fuel pump module.
Monitor the fuel pressure gauge for a minimum of 5 minutes.
NOTE: The pressure should not fall below 241 KPa (35 psi)
Does the fuel pressure drop?

Yes → Replace leaking fuel injectors.

Perform POWERTRAIN VERIFICATION TEST VER - 2.
No → Test Complete.

283
bY dR.dEaDhEaD
STARTING

Symptom:
*NO CRANK CONDITION

POSSIBLE CAUSES
MECHANICAL CONDITION
TRANSMISSION RANGE SENSOR
BATTERY CIRCUIT RESISTANCE TOO HIGH
CLUTCH PEDAL POSITION SWITCH
(T141) FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
TRS T41 SENSE (P/N SENSE) CIRCUIT OPEN
(T40) STARTER RELAY OUTPUT CIRCUIT OPEN
(A2) FUSED B+ CIRCUIT OPEN
STARTER
STARTER RELAY

TEST ACTION APPLICABILITY

1 NOTE: Check all fuses and verify the battery is fully charged and capable of All
passing a load test before continuing.
WARNING: MAKE SURE THE BATTERY IS DISCONNECTED, THEN WAIT
TWO MINUTES BEFORE PROCEEDING.
Turn the engine over by hand to ensure the engine is not seized.
Is the engine able to turn over?

Yes → Go To 2
No → Repair the mechanical condition preventing the starter motor
from cranking.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2 Turn the ignition off. All

Disconnect the PCM harness connectors.
Move the Gear selector through all gear positions, from Park to 1st and back.
While moving the gear selector through each gear, measure the resistance between
ground and the TRS T41 Sense (P/N Sense) circuit.
Did the resistance change from above 10.0 ohms to below 10.0 ohms?

Yes → Go To 3

No → Replace the Transmission Range Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

3 Check the Battery Cables for high resistance using the service information proce- All
dure.
Did either Battery Cable have a voltage drop greater than 0.2 of a volt?

Yes → Repair the Battery circuit for high resistance.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Go To 4

284
bY dR.dEaDhEaD
 STARTING

*NO CRANK CONDITION — Continued

TEST ACTION APPLICABILITY

4 Disconnect the Clutch Pedal Position Switch. All
If this vehicle is not equipped with a manual transmission answer NO to this test and
continue.
Connect a jumper wire between the two terminals of the Clutch Pedal Position
Switch and attempt to start the engine.
Does the engine crank?

Yes → Replace the Clutch Pedal Position Switch.

Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Go To 5

5 Turn ignition off. All

Remove the Starter Relay from PDC.
WARNING: The Parking Brake must be on and the Transmission must be in
park for a vehicle equipped with an automatic transmission or Neutral on
a Manual transmission.
WARNING: The engine may be cranked in the next step. Keep away from
moving engine parts.
Briefly connect a jumper wire between Starter Relay B+ circuit and the (T40) Starter
Relay Output circuits.
Did the Starter Motor crank the engine?
Yes → Go To 6
No → Go To 8

NOTE: Remove the jumper wire before continuing.

6 Ignition on, engine not running. All

Using a 12-volt test light connected to ground, probe the (T141) Fused Ignition
Switch Output circuit in the Starter Relay connector.
While observing 12-volt test light, hold ignition key in the start position.
Does the test light illuminate brightly?
Yes → Go To 7

No → Repair the open or high resistance in the (T141) Fused Ignition

Switch Output circuit. Inspect related fuses and repair as neces-
sary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

7 Turn the ignition off. All

Disconnect the PCM harness connectors.
Measure the resistance of the Starter Relay Control circuit between the Relay
terminal and the PCM harness connector.
Is the resistance below 5.0 ohms?
Yes → Replace the Starter Motor Relay.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Repair the open in the TRS T41 Sense (P/N Sense) circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

285
bY dR.dEaDhEaD
STARTING

*NO CRANK CONDITION — Continued

TEST ACTION APPLICABILITY

8 Disconnect the Starter Relay Output connector from the Starter Solenoid. All
Measure the resistance of the (T40) Starter Relay Output circuit between the Relay
and the Solenoid harness connector.
Is the resistance below 5.0 ohms?
Yes → Go To 9

No → Repair the open in the (T40) Starter Relay Output circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

9 Using a 12-volt test light connected to ground, backprobe the (A2) Fused B+ circuit All
at the Starter Relay terminal.
Does the test light illuminate brightly?

Yes → Go To 10

No → Repair the open or high resistance in the (A2) Fused B+ circuit.

Inspect related fuses and repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

10 If there are no other possible causes remaining, review repair. All

Repair
Replace the Starter.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

286
bY dR.dEaDhEaD
 STARTING

Symptom:
*NO RESPONSE FROM PCM WITH A NO START CONDITION

POSSIBLE CAUSES
PCM FUSED B+ CIRCUIT
PCM NO RESPONCE
PCM FUSED IGNITION SWITCH OUTPUT CIRCUIT
PCM GROUND CIRCUITS
TP SENSOR
5-VOLT SENSOR OPEN OR SHORTED
(K7) 5-VOLT SUPPLY CKT SHORT TO GROUND
(K6) 5-VOLT CIRCUIT SUPPLY SHORTED TO GROUND
PCM

TEST ACTION APPLICABILITY

1 NOTE: The DRBIIIt and cable must be operating properly for the results of All
this test to be valid.
NOTE: Ensure the ignition switch was on while trying to communicate with
the PCM.
Turn the ignition off.
Disconnect the PCM harness connectors.
Using a 12-volt test light connected to ground, backprobe the PCM Fused B+ circuit
in the PCM harness connector.
Does the test light illuminate brightly?

Yes → Go To 2
No → Repair the open in the Fused B+ circuit. Inspect and replace fuses
as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2 Ignition on, engine not running. All

Using a 12-volt test light connected to ground, backprobe the PCM Fused Ignition
Switch Output circuit in the PCM harness connector.
Does the test light illuminate brightly?
Yes → Go To 3

No → Repair the open in the Ignition Switch Output circuit. Inspect and
replace fuses as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

3 Turn the ignition off. All

Using a 12-volt test light connected to 12-volts, backprobe the PCM ground circuits
in the PCM harness connector.
Does the test light illuminate brightly?
Yes → Go To 4

No → Repair the opens in the PCM ground circuits.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

287
bY dR.dEaDhEaD
STARTING

*NO RESPONSE FROM PCM WITH A NO START CONDITION — Continued

TEST ACTION APPLICABILITY

4 Connect the PCM harness connectors. All
Disconnect the TP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the (K7) 5-volt Supply circuit.
Is the voltage between 4.5 and 5.2 volts?

Yes → Go To 5

No → Go To 6

5 Turn the ignition off. All

Disconnect the MAP Sensor harness connector.
NOTE: Connect the TP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the (K7) 5-volt Supply circuit in the MAP Sensor harness
connector.
Is the voltage between 4.5 and 5.2 volts?

Yes → If communication is available with a PCM on a like vehicle,

replace and program the Powertrain Control Module in accor-
dance with Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Replace the Throttle Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

6 Measure the voltage on the (K7) 5-volt Supply circuit. All

Disconnect all the sensors that use a 5-volt Supply circuit.
Did the voltage return to 4.5 to 5.2 volts when disconnecting any of the sensors.
Yes → Replace the sensor that is pulling down the 5-volt supply.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Go To 7

7 Turn the ignition off. All

Disconnect PCM harness connectors.
Measure the resistance between ground and the (K7) 5-volt Supply circuit with all
the Sensor harness connectors disconnected.
Is the resistance below 100 ohms?
Yes → Repair the short to ground in the (K7) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Go To 8

8 Disconnect all sensors that use the (K6) 5-volt Supply. All
Measure the resistance between ground and the (K6) 5-volt Supply circuit at the
PCM harness connector.
Is the resistance below 100 ohms?

Yes → Repair the short to ground in the (K6) 5-volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Go To 9

288
bY dR.dEaDhEaD
 STARTING

*NO RESPONSE FROM PCM WITH A NO START CONDITION — Continued

TEST ACTION APPLICABILITY

9 NOTE: Before continuing, check the PCM harness connector terminals for All
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there is no possible causes remaining, view repair.

Repair
Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

289
bY dR.dEaDhEaD
STARTING

Symptom:
*START AND STALL CONDITION

POSSIBLE CAUSES
CHECKING DTCS
CHECKING SKIM DTCS
TP SENSOR SWEEP
TP SENSOR VOLTAGE GREATER THAN 0.92 VOLTS WITH THROTTLE CLOSED
ECT SENSOR OPERATION
OTHER POSSIBLE CAUSES FOR START & STALL
FUEL CONTAMINATION

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
With the DRBIIIt, read engine DTCs.
Are any DTCs present?
Yes → Refer to the Driveability Category and perform the appropriate
symptom.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No → Go To 2

2 NOTE: If you are unable to communicate with the SKIM, refer to the All
Communication Category and perform the appropriate symptom.
With the DRBIIIt, read the SKIM codes.
Are there any SKIM DTCs?

Yes → Refer to the Vehicle Theft category and perform the appropriate
symptom.
Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Go To 3

3 With the DRBIIIt, read TP Sensor voltage. All

While monitoring the DRBIIIt, slowly open and close the Throttle.
Is the voltage change smooth?
Yes → Go To 4

No → Replace the Throttle Position Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

4 With the DRBIIIt, read TP Sensor voltage. Throttle must be against stop. All
Is the voltage 0.92 or less with the Throttle closed?

Yes → Go To 5
No → Check for a binding throttle condition. If OK, replace the Throttle
Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

290
bY dR.dEaDhEaD
 STARTING

*START AND STALL CONDITION — Continued

TEST ACTION APPLICABILITY

5 Note: For this test to be valid, the thermostat must be operating correctly. All
Note: This test works best if performed on a cold engine (cold soaked).
NOTE: If the vehicle was allowed to sit over night with no engine start,
coolant temperature should be near ambient temperatures.
Ignition on, engine not running.
With the DRBIIIt, read the ECT value.
Note: If engine coolant temperature is above 82° C (180° F), allow the engine
to cool until 65° C (150° F) is reached.
Start the engine.
During engine warm-up, monitor the ECT Sensor value. The temperature value
change should be a smooth transition from start up to normal operating temp 82° C
(180° F). The value should reach at least 82° C (180° F).
Did the Engine Temperature value increase smoothly and did it reach at least 82° C
(180° F)?
Yes → Go To 6

No → Replace the Engine Coolant Temperature Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

6 The following additional items should be checked as a possible cause for a start and All
stall condition.
Refer to any Technical Service Bulletins (TSB’s) that may apply to the symptom.
The exhaust system must be free of any restrictions.
The engine compression must be within specifications.
The engine valve timing must be within specifications.
The engine must be free from vacuum leaks.
The throttle body must be free of carbon buildup and dirt.
Do any of the above conditions exist?

Yes → Repair as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 1.
No → Go To 7

7 Verify that the Fuel tank is not empty before continuing. All
Follow the diagnostics for Checking Fuel Delivery under the Driveability section of
this manual.
Was the Start and Stall condition solved after following the above diagnostic test?

Yes → Test Complete.

No → Check for contamination/water in the fuel. Ensure the fuel being
used in this vehicle meets manufactures Fuel Requirement, refer
to the service manual.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

291
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0122-THROTTLE POSITION SENSOR/APPS LOW

When Monitored and Set Condition:

P0122-THROTTLE POSITION SENSOR/APPS LOW

When Monitored: Continuously with the ignition on and engine running.
Set Condition: This DTC will set if the monitored TPS voltage drops below .078 volts for
the period of 0.48 seconds.

POSSIBLE CAUSES
ENGINE TPS DTC’S PRESENT
TPS SIGNAL CIRCUIT HIGH RESISTANCE
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, check Engine DTC’s. All

Are there any Engine TPS related DTCs present?

Yes → Refer to the Powertrain category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

292
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0122-THROTTLE POSITION SENSOR/APPS LOW — Continued

TEST ACTION APPLICABILITY

3 With the DRBIIIt in Transmission Sensors, read the TPS voltage. All
Is the TPS voltage below 0.5 volts?

Yes → Go To 4
No → Go To 6

4 Ignition on, engine not running. All

With the DRBIIIt in Transmission Sensors, record the TPS voltage.
While back probing the TCM harness connector, measure the voltage of the TPS
Signal circuit.
Compare the voltage readings between the DRBIIIt and the reading from the digital
multi meter.
Are the voltages within 0.1 volt of each other?

Yes → Repair the TPS signal circuit between the TCM harness connector
and the splice for high resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 5

5 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorts and open circuits.
Pay particular attention to the point where the TPS signal and sensor ground circuits
splice off from the engine circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

293
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0123-THROTTLE POSITION SENSOR/APPS HIGH

When Monitored and Set Condition:

P0123-THROTTLE POSITION SENSOR/APPS HIGH

When Monitored: Continuously with the ignition on and engine running.
Set Condition: This DTC will set if the monitored TPS voltage rises above 4.94 volts for
the period of 0.48 seconds.

POSSIBLE CAUSES
ENGINE TPS DTC’S PRESENT
SENSOR GROUND CIRCUIT OPEN TO TCM
TPS SIGNAL CIRCUIT OPEN TO TCM
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, check Engine DTC’s. All

Are there any Engine TPS related DTCs present?

Yes → Refer to the Powertrain category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

294
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0123-THROTTLE POSITION SENSOR/APPS HIGH — Continued

TEST ACTION APPLICABILITY

3 With the DRBIIIt in Transmission Sensors, read the TPS voltage. All
Is the TPS voltage above 4.5 volts?

Yes → Go To 4
No → Go To 7

4 Turn the ignition off to the lock position. All

Disconnect the TPS harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the TPS Signal Circuit from the TCM harness connector to
the TPS harness connector.
Is the resistance below 5.0 ohms?

Yes → Go To 5

No → Repair the TPS Signal circuit between the TCM harness connec-
tor and the splice for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

5 Turn the ignition off to the lock position. All

Disconnect the TPS harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Sensor Ground circuit between the TPS harness
connector and the Transmission Control Module harness connector.
Is the resistance below 5.0 ohms?
Yes → Go To 6

No → Repair the Sensor Ground circuit between the TCM harness

connector and the splice for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

7 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorts and open circuits.
Pay particular attention to the point where the TPS signal and sensor ground circuits
splice off from the engine circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

295
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0124- THROTTLE POSITION SENSOR/APPS INTERMITTENT

When Monitored and Set Condition:

P0124- THROTTLE POSITION SENSOR/APPS INTERMITTENT

When Monitored: Continuously with the ignition on and engine running.
Set Condition: This DTC will set with a throttle angle between 6° and 120.6° with a 5° or
higher change under 7.0 milliseconds.

POSSIBLE CAUSES
ENGINE TPS DTC’S PRESENT
THROTTLE POSITION SENSOR
TRANSMISSION CONTROL MODULE

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, check Engine DTC’s. All

Are any Engine TPS related DTC’s present?

Yes → Refer to the Powertrain category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

296
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0124- THROTTLE POSITION SENSOR/APPS INTERMITTENT —

Continued
TEST ACTION APPLICABILITY
3 Ignition On, Engine Not Running. All
With the DRBIIIt, under Transmission Sensors, monitor the TPS voltage in the
following step.
Slowly open and close the throttle while checking for erratic voltage changes.
Did the TPS voltage change smooth and consistent?

Yes → Go To 4

No → Replace the Throttle Position Sensor per the Service Information.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

4 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

297
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0218-HIGH TEMPERATURE OPERATION ACTIVATED

When Monitored and Set Condition:

P0218-HIGH TEMPERATURE OPERATION ACTIVATED

When Monitored: Whenever the engine is running.
Set Condition: Immediately when the Overheat shift schedule is activated 116 C (240 F)
Transmission oil temp.

POSSIBLE CAUSES
ENGINE COOLING SYSTEM MALFUNCTION
TRANSMISSION OIL COOLER PLUGGED
HIGH TEMPERATURE OPERATIONS ACTIVATED

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

298
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0218-HIGH TEMPERATURE OPERATION ACTIVATED — Continued

TEST ACTION APPLICABILITY

2 This DTC is an informational DTC designed to aid the Technician in diagnosing shift All
quality complaints.
This DTC indicates that the Transmission has been operating in the 9Overheat9 shift
schedule which may generate a customer complaint.
The customer driving patterns may indicate the need for an additional Transmission
Oil Cooler.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair the cause of the Transmission Overheating per the Service
Information. If indicated install an additional Transmission Oil
Cooler.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

3 Perform Engine Cooling System diagnostics per the Service Information All
Is the Engine Cooling System functioning properly?
Yes → Go To 4

No → Repair the cause of the Engine Overheating. Refer to the Service

Information for additional repair information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

4 If there are no possible causes remaining, view repair. All

Repair
Flush or replace the Transmission Oil cooler as necessary per the
Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

299
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0562-LOW BATTERY VOLTAGE

When Monitored and Set Condition:

P0562-LOW BATTERY VOLTAGE

When Monitored: With the engine running and the TCM has closed the Transmission
Control Relay.
Set Condition: If battery voltage at TCM Transmission Control Relay Output Sense
circuit is less than 10.0 volts for 15 seconds. *This DTC generally indicates a gradually
falling battery voltage or resistive connections to the TCM.

POSSIBLE CAUSES
RELATED CHARGING SYSTEM DTCS
INTERMITTENT WIRING AND CONNECTORS
FUSED B+ CIRCUIT OPEN OR HIGH RESISTANCE
GROUND CIRCUIT OPEN OR HIGH RESISTANCE
TRANS CONTROL RELAY OUTPUT TO TCM OPEN OR HIGH RESISTANCE
TRANSMISSION CONTROL RELAY OPEN OR HIGH RESISTANCE
TRANSMISSION CONTROL MODULE

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

300
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0562-LOW BATTERY VOLTAGE — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, read the PCM DTC’s. All
Are there any Charging System related DTC’s stored in the PCM?

Yes → Refer to the Charging System category and repair any PCM
Charging System DTC’s first. NOTE: After repairing the PCM
charging system DTC’s, perform the Transmission Verification
test to verify the transmission was not damaged.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

3 NOTE: Generator, battery, and charging system must be fully functional All
before performing this test.
With the DRBIIIt, read Transmission DTC’s.
With the DRBIIIt, Check the STARTS SINCE SET counter for P0562.
Note: This counter only applies to the last DTC set.
Is the Starts Since Set counter for P0562 set at 0?

Yes → Go To 4
No → Go To 9

4 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Using a 12-volt test light connected to 12-volts, check the ground circuits in the TCM
harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly for all the ground circuits?
Yes → Go To 5

No → Repair the Ground circuit(s) for an open or high resistance.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

5 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Fused B+ circuit in the TCM
harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 6
No → Repair the Fused B+ circuit for an open or high resistance. If the
fuse is open make sure to check for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

301
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0562-LOW BATTERY VOLTAGE — Continued

TEST ACTION APPLICABILITY

6 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check both Transmission Control
Relay Output circuits in the TCM harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?
Yes → Go To 7

No → Repair the Transmission Control Relay Output circuit for an open

or high resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

7 Turn the ignition off to the lock position. All

Install a substitute Relay in place of the Transmission Control Relay.
Start the engine.
Using a voltmeter, measure the battery voltage.
With the DRBIIIt, monitor the Transmission Switched Battery Voltage.
Compare the DRBIIIt Transmission Switched Battery voltage to the actual battery
voltage.
Is the DRBIIIt voltage within 2.0 volts of the battery voltage?
Yes → Replace the Transmission Control Relay.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

8 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

9 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

302
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0604-INTERNAL TCM

When Monitored and Set Condition:

P0604-INTERNAL TCM
When Monitored:
Set Condition: The TCM is reporting internal errors and must be replaced.

POSSIBLE CAUSES
TCM - INTERNAL ERROR

TEST ACTION APPLICABILITY

1 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

303
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0605-INTERNAL TCM

When Monitored and Set Condition:

P0605-INTERNAL TCM
When Monitored:
Set Condition: The TCM is reporting internal errors and must be replaced.

POSSIBLE CAUSES
TCM - INTERNAL ERROR

TEST ACTION APPLICABILITY

1 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

304
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0613-INTERNAL TCM

When Monitored and Set Condition:

P0613-INTERNAL TCM
When Monitored:
Set Condition: The TCM is reporting internal errors and must be replaced.

POSSIBLE CAUSES
TCM - INTERNAL ERROR

TEST ACTION APPLICABILITY

1 NOTE: Make sure this DTC is set in the TCM before making repair. All
Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

305
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0706-CHECK SHIFTER SIGNAL

When Monitored and Set Condition:

P0706-CHECK SHIFTER SIGNAL

When Monitored: Continuously with the ignition key on.
Set Condition: 3 occurrences in one key start of an invalid PRNDL code which lasts for
more than 0.1 second.

POSSIBLE CAUSES
CONDITION P0706 PRESENT
TRS T1 SENSE CIRCUIT OPEN
TRS T3 SENSE CIRCUIT OPEN
TRS T41 SENSE CIRCUIT OPEN
TRS T42 SENSE CIRCUIT OPEN
TRS T1 SENSE CIRCUIT SHORT TO GROUND
TRS T3 SENSE CIRCUIT SHORT TO GROUND
TRS T41 SENSE CIRCUIT SHORT TO GROUND
TRS T42 SENSE CIRCUIT SHORT TO GROUND
TRS T1 SENSE CIRCUIT SHORT TO VOLTAGE
TRS T3 SENSE CIRCUIT SHORT TO VOLTAGE
TRS T41 SENSE CIRCUIT SHORT TO VOLTAGE
TRS T42 SENSE CIRCUIT SHORT TO VOLTAGE
TRANSMISSION RANGE SENSOR
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

306
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0706-CHECK SHIFTER SIGNAL — Continued

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 Using the DRBIIIt, perform the Shift Lever Position Test. All
Select the test outcome from the following:

Test passes
Go To 3

Test fails with DTC

Go To 4
Test fails without DTC
Adjust the shift linkage per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

3 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

307
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0706-CHECK SHIFTER SIGNAL — Continued

TEST ACTION APPLICABILITY

4 Turn the ignition off to the lock position. All
CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the DRBIIIt, perform the Shift Lever Position Test.
When the DRBIII t instructs you to put the Gear Selector in a particular position,
you must do so using the Transmission Simulator. The LED for the gear position in
question must be illuminated prior to hitting 9enter9 on the DRBIIIt.
Did the test pass?

Yes → Go To 5

No → Go To 6
NOTE: Disconnect the Transmission Simulator and reconnect all the har-
ness connectors.

5 If there are no possible causes remaining, view repair. All

Repair
Replace the Transmission Range Sensor per the Service Informa-
tion.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Ignition on, engine not running. All

With the DRBIIIt in Inputs/Outputs, read the TRS Sense circuits C1 thru C4.
Move the shift lever thru all gear positions, pausing momentarily in each gear
position. Watch for one of the circuits to not change state.
Pick the one that did not change state.
TRS T1 sense (C4)
Go To 7
TRS T3 sense (C3)
Go To 10

TRS T41 sense (C1)

Go To 13

TRS T42 sense (C2)

Go To 16

7 Turn the ignition off to the lock position. All

Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the TRS T1 Sense circuit from the TCM harness connector
to the TRS harness connector.
Is the resistance above 5.0 ohms?

Yes → Repair the TRS T1 Sense circuit for an open.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

308
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0706-CHECK SHIFTER SIGNAL — Continued

TEST ACTION APPLICABILITY

8 Turn the ignition off to the lock position. All
Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the TRS T1 circuit in the TCM harness
connector.
Is the resistance below 5.0 ohms?

Yes → Repair the TRS T1 Sense circuit for a short to ground.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 9

9 Turn the ignition off to the lock position. All

Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Measure the voltage of the TRS T1 Sense circuit.
Is the voltage above 0.5 volt?
Yes → Repair the TRS T1 Sense circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 19

10 Turn the ignition off to the lock position. All

Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the TRS T3 Sense circuit from the TCM harness connector
to the TRS harness connector.
Is the resistance above 5.0 ohms?
Yes → Repair the TRS T3 Sense circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 11

11 Turn the ignition off to the lock position. All

Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the TRS T3 Sense circuit in the TCM
harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the TRS T3 Sense circuit for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 12

309
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0706-CHECK SHIFTER SIGNAL — Continued

TEST ACTION APPLICABILITY

12 Turn the ignition off to the lock position. All
Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PCM.
Ignition on, engine not running.
Measure the voltage of the TRS T3 Sense circuit.
Is the voltage above 0.5 volt?

Yes → Repair the TRS T3 Sense circuit for a short to voltage.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 19

13 Turn the ignition off to the lock position. All

Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the TRS T41 Sense circuit from the TCM connector to the
TRS connector.
Is the resistance above 5.0 ohms?
Yes → Repair the TRS T41 Sense circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 14

14 Turn the ignition off to the lock position. All

Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the TRS T41 Sense circuit in the TCM
harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the TRS T41 Sense circuit for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 15

15 Turn the ignition off to the lock position. All

Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Measure the voltage of the TRS T41 Sense circuit.
Is the voltage above 0.5 volt?

Yes → Repair the TRS T41 Sense circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 19

310
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0706-CHECK SHIFTER SIGNAL — Continued

TEST ACTION APPLICABILITY

16 Turn the ignition off to the lock position. All
Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the TRS T42 Sense circuit from the TCM harness
connector to the TRS harness connector.
Is the resistance above 5.0 ohms?

Yes → Repair the TRS T42 Sense circuit for an open.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 17

17 Turn the ignition off to the lock position. All

Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the TRS T42 Sense circuit in the TCM
harness connector.
Is the resistance below 5.0 ohms?
Yes → Repair the TRS T42 Sense circuit for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 18

18 Turn the ignition off to the lock position. All

Disconnect the TRS harness connector.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Measure the voltage of the TRS T42 Sense circuit.
Is the voltage above 0.5 volt?
Yes → Repair the TRS T42 Sense circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 19

19 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

311
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0711-TRANSMISSION TEMPERATURE SENSOR PERFORMANCE

When Monitored and Set Condition:

P0711-TRANSMISSION TEMPERATURE SENSOR PERFORMANCE

When Monitored: Continuously with the ignition on and engine running.
Set Condition: This DTC will set when the desired transmission temperature does not
reach a normal operating temperature within a given time frame. Time is variable due to
ambient temperature. Approximate times are starting temperature to warm up time: (-40°
F / -40° C - 35 min) (-20° F / -28° C - 25 min) (20° F / -6.6° C - 20 min) (60° F / 15.5 ° C - 10
min)

POSSIBLE CAUSES
RELATED DTC’S PRESENT
TRANSMISSION TEMPERATURE SENSOR
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.
Continue
Go To 2

312
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0711-TRANSMISSION TEMPERATURE SENSOR PERFORMANCE —

Continued
TEST ACTION APPLICABILITY
2 With the DRBIIIt, check Transmission DTC’s. All
Are there any other Transmission Temperature Sensor related DTCs present?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, Check the STARTS SINCE SET counter for P0711. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

Yes → Go To 4

No → Go To 7

4 Turn the ignition off to the lock position. All

Remove the Starter Relay.
NOTE: Failure to remove Starter Relay can cause a Transmission - No
Response condition.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the Transmission Simulator, turn the Input/Output switch to OFF.
With the DRBIIIt, monitor the TRANS TEMP VOLTS while turning the Thermistor
Voltage switch to all three positions on the Transmission Simulator.
Compare the DRBIIIt readings with the numbers listed on the Transmission
Simulator.
Do the readings on the Transmission Simulator match the DRBIIIt readings ± 0.2
volts?
Yes → Go To 5
No → Go To 6

5 If there are no possible causes remaining, view repair. All

Repair
Replace Transmission Solenoid/TRS Assembly per the Service
Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

313
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0711-TRANSMISSION TEMPERATURE SENSOR PERFORMANCE —

Continued
TEST ACTION APPLICABILITY
7 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

314
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0712-TRANSMISSION TEMPERATURE SENSOR LOW

When Monitored and Set Condition:

P0712-TRANSMISSION TEMPERATURE SENSOR LOW

When Monitored: Continuously with the ignition on and engine running.
Set Condition: The DTC will set when the monitored Temperature Sensor voltage drops
below 0.078 volts for the period of 0.45 seconds.

POSSIBLE CAUSES
RELATED DTC’S PRESENT
TRANSMISSION TEMPERATURE SENSOR SIGNAL CIRCUIT SHORT TO GROUND
TRANSMISSION TEMPERATURE SENSOR
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, check Transmission DTC’s. All

Are there any Speed Sensor DTCs present?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

315
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0712-TRANSMISSION TEMPERATURE SENSOR LOW — Continued

TEST ACTION APPLICABILITY

3 With the DRBIIIt, Check the STARTS SINCE SET counter for P0712. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

Yes → Go To 4
No → Go To 8

4 Turn the ignition off to the lock position. All

Remove the Starter Relay.
NOTE: Failure to remove Starter Relay can cause a Transmission - No
Response condition.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the Transmission Simulator, turn the Input/Output switch to OFF.
With the DRBIIIt, monitor the TRANS TEMP VOLTS while turning the Thermistor
Voltage switch to all three positions on the Transmission Simulator.
Compare the DRBIIIt readings with the numbers listed on the Transmission
Simulator.
Do the readings on the Transmission Simulator match the DRBIIIt readings ± 0.2
volts?
Yes → Go To 5
No → Go To 6

5 If there are no possible causes remaining, view repair. All

Repair
Replace Transmission Solenoid/TRS Assembly per the Service
Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector..
Disconnect the Transmission Solenoid/TRS Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Transmission Temperature Sensor
Signal circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the Transmission Temperature Sensor Signal circuit for a

short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

7 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

316
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0712-TRANSMISSION TEMPERATURE SENSOR LOW — Continued

TEST ACTION APPLICABILITY

8 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

317
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0713-TRANSMISSION TEMPERATURE SENSOR HIGH

When Monitored and Set Condition:

P0713-TRANSMISSION TEMPERATURE SENSOR HIGH

When Monitored: Continuously with the ignition on and engine running.
Set Condition: The DTC will set when the monitored Temperature Sensor voltage rises
above 4.94 volts for the period of 0.45 seconds.

POSSIBLE CAUSES
TRANSMISSION TEMPERATURE SENSOR SIGNAL CIRCUIT OPEN
TRANSMISSION TEMPERATURE SENSOR SIGNAL CIRCUIT SHORT TO VOLTAGE
TRANSMISSION TEMPERATURE SENSOR
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, Check the STARTS SINCE SET counter for P0713. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

Yes → Go To 3

No → Go To 8

318
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0713-TRANSMISSION TEMPERATURE SENSOR HIGH — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off to the lock position. All
Remove the Starter Relay.
NOTE: Failure to remove Starter Relay can cause a Transmission - No
Response condition.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the Transmission Simulator, turn the Input/Output switch to OFF.
With the DRBIIIt, monitor the TRANS TEMP VOLTS while turning the Thermistor
Voltage switch to all three positions on the Transmission Simulator.
Compare the DRBIIIt readings with the numbers listed on the Transmission
Simulator.
Do the readings on the Transmission Simulator match the DRBIIIt readings ± 0.2
volts?
Yes → Go To 4
No → Go To 5

4 If there are no possible causes remaining, view repair. All

Repair
Replace Transmission Solenoid/TRS Assembly per the Service
Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

5 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector..
Disconnect the Transmission Solenoid /TRS Assembly harness connector
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Transmission Temperature Sensor Signal circuit from
the TCM harness connector to the Transmission Solenoid/TRS Assembly harness
connector.
Is the resistance above 5.0 ohms?
Yes → Repair the Transmission Temperature Sensor Signal circuit for
an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 6

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the Transmission Temperature Sensor Signal circuit in the
TCM harness connector.
Is the voltage above 0.5 volts?

Yes → Repair the Transmission Temperature Sensor Signal circuit for a

short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

319
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0713-TRANSMISSION TEMPERATURE SENSOR HIGH — Continued

TEST ACTION APPLICABILITY

7 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

8 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

320
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0714-TRANSMISSION TEMPERATURE SENSOR INTERMITTENT

When Monitored and Set Condition:

P0714-TRANSMISSION TEMPERATURE SENSOR INTERMITTENT

When Monitored: Continuously with the ignition on and engine running.
Set Condition: The DTC will set when the monitored Temperature Sensor voltage
fluctuates or changes abruptly within a predetermined period of time.

POSSIBLE CAUSES
RELATED DTC’S PRESENT
TRANSMISSION TEMPERATURE SENSOR
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, check Transmission DTC’s. All

Are there any Speed Sensor and/or other Temperature Sensor DTCs present?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

321
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0714-TRANSMISSION TEMPERATURE SENSOR INTERMITTENT —

Continued
TEST ACTION APPLICABILITY
3 With the DRBIIIt, Check the STARTS SINCE SET counter for P0714. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

Yes → Go To 4
No → Go To 7

4 Turn the ignition off to the lock position. All

Remove the Starter Relay.
NOTE: Failure to remove Starter Relay can cause a Transmission - No
Response condition.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the Transmission Simulator, turn the Input/Output switch to OFF.
With the DRBIIIt, monitor the TRANS TEMP VOLTS while turning the Thermistor
Voltage switch to all three positions on the Transmission Simulator.
Compare the DRBIIIt readings with the numbers listed on the Transmission
Simulator.
Do the readings on the Transmission Simulator match a non-fluctuating DRBIIIt
reading ± 0.2 volts?
Yes → Go To 5
No → Go To 6

5 If there are no possible causes remaining, view repair. All

Repair
Replace Transmission Solenoid/TRS Assembly per the Service
Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

7 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

322
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0715-INPUT SPEED SENSOR ERROR

When Monitored and Set Condition:

P0715-INPUT SPEED SENSOR ERROR

When Monitored: The transmission gear ratio is monitored continuously while the
transmission is in gear.
Set Condition: If there is an excessive change in input RPM in any gear.

POSSIBLE CAUSES
INPUT SPEED SENSOR SIGNAL CIRCUIT OPEN
SPEED SENSOR GROUND CIRCUIT OPEN
INPUT SPEED SENSOR SIGNAL CIRCUIT SHORT TO GROUND
INPUT SPEED SENSOR SIGNAL CIRCUIT SHORT TO VOLTAGE
SPEED SENSOR GROUND CIRCUIT SHORT TO VOLTAGE
INPUT SPEED SENSOR ERROR
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

323
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0715-INPUT SPEED SENSOR ERROR — Continued

TEST ACTION APPLICABILITY

2 Start the engine in park. All
With the DRBIIIt, read the Input RPM.
Is the Input RPM reading below 400 RPM?

Yes → Go To 3
No → Go To 11

3 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the Transmission Simulator, set the 9Input/Output Speed9 switch to 9ON9 and
the rotary switch to the 93000/12509 position.
With the DRBIIIt, monitor the Input and Output RPM.
Does the Input RPM read 3000 RPM and the Output RPM read 1250 RPM +/- 50
RPM?

Yes → Go To 4
No → Go To 5
NOTE: Disconnect the Transmission Simulator and reconnect all harness
connectors.

4 If there are no possible causes remaining, view repair. All

Repair
Replace the Input Speed Sensor per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

5 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Input Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Input Speed Sensor Signal circuit from the TCM
harness connector to the Input Speed Sensor harness connector.
Is the resistance above 5.0 ohms?

Yes → Repair the Input Speed Sensor Signal circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 6

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Input Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Input Speed Sensor signal circuit.
Is the resistance Below 5.0 ohms?
Yes → Repair the Input Speed Sensor Signal circuit for a short to
ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 7

324
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0715-INPUT SPEED SENSOR ERROR — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off to the lock position. All
Disconnect the Input Speed Sensor harness connector.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the Input Speed Sensor Signal circuit in the TCM harness
connector.
Is the voltage above 0.5 volts?

Yes → Repair the Input Speed Sensor Signal circuit for a short to
voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Input Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Speed Sensor Ground circuit from the TCM harness
connector to the Input Speed Sensor harness connector.
Is the resistance above 5.0 ohms?
Yes → Repair the Speed Sensor Ground circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 9

9 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the TRS harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Measure the voltage of the Speed Sensor Ground circuit in the TCM harness
connector.
Is the voltage above 0.5 volts?

Yes → Repair the Speed Sensor Ground circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 10

10 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

325
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0715-INPUT SPEED SENSOR ERROR — Continued

TEST ACTION APPLICABILITY

11 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

326
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0720-OUTPUT SPEED SENSOR ERROR

When Monitored and Set Condition:

P0720-OUTPUT SPEED SENSOR ERROR

When Monitored: The transmission gear ratio is monitored continuously while the
transmission is in gear.
Set Condition: If there is an excessive change in output RPM in any gear.

POSSIBLE CAUSES
INTERMITTENT WIRING AND CONNECTORS
OUTPUT SPEED SENSOR SIGNAL CIRCUIT OPEN
SPEED SENSOR GROUND CIRCUIT OPEN
OUTPUT SPEED SENSOR SIGNAL CIRCUIT SHORT TO GROUND
OUTPUT SPEED SENSOR SIGNAL CIRCUIT SHORT TO VOLTAGE
SPEED SENSOR GROUND CIRCUIT SHORT TO VOLTAGE
OUTPUT SPEED SENSOR ERROR
TRANSMISSION CONTROL MODULE

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

327
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0720-OUTPUT SPEED SENSOR ERROR — Continued

TEST ACTION APPLICABILITY

2 Start the engine in park. All
Raise the drive wheels off of the ground.
WARNING: PROPERLY SUPPORT THE VEHICLE.
Place transmission in drive, release foot from brake.
WARNING: BE SURE TO KEEP HANDS AND FEET CLEAR OF ROTATING
WHEELS.
Note: The drive wheels must be turning at this point.
With the DRBIIIt, read the Output RPM
Is the Output RPM below 100 RPM?

Yes → Go To 3

No → Go To 11

3 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the Transmission Simulator, set the 9Input/Output Speed9 switch to 9ON9 and
the rotary switch to the 93000/12509 position.
With the DRBIIIt, read the Input RPM and Output RPM.
Does the Input RPM read 3000 and the Output RPM read 1250 ± 50 RPM?
Yes → Go To 4
No → Go To 5

4 If there are no possible causes remaining, view repair. All

Repair
Replace the Output Speed Sensor per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

5 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Output Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Output Speed Sensor Signal circuit from the TCM
harness connector to the Output Speed Sensor harness connector.
Is the resistance above 5.0 ohms?
Yes → Repair the Output Speed Sensor Signal circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 6

328
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0720-OUTPUT SPEED SENSOR ERROR — Continued

TEST ACTION APPLICABILITY

6 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Output Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Output Speed Sensor Signal circuit.
Is the resistance Below 5.0 ohms?

Yes → Repair the Output Speed Sensor Signal circuit for a short to
ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

7 Turn ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Simulator.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B(+) and Transmission Control Relay
Output circuits in the Transmission Control Relay connector (In PDC).
Ignition on, engine not running.
Measure the voltage of the Output Speed Sensor Signal circuit in the TCM connector.
Is the voltage above 3.0 volts?
Yes → Repair Output Speed Sensor Signal circuit short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Output Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Speed Sensor Ground circuit from the TCM harness
connector to the Output Speed Sensor harness connector.
Is the resistance above 5.0 ohms?
Yes → Repair the Speed Sensor Ground circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 9

9 Turn ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the TRS harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B(+) and Transmission Control Relay
Output circuits in the Transmission Control Relay connector (In PDC).
Ignition on, engine not running.
Measure the voltage of the Speed Sensor Ground circuit in the TCM connector.
Is the voltage above 3.0 volts?

Yes → Repair the Speed Sensor Ground circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 10

329
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0720-OUTPUT SPEED SENSOR ERROR — Continued

TEST ACTION APPLICABILITY

10 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

11 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

330
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0725-ENGINE SPEED SENSOR CIRCUIT

When Monitored and Set Condition:

P0725-ENGINE SPEED SENSOR CIRCUIT

When Monitored: Whenever the engine is running.
Set Condition: Engine RPM less than 390 or greater than 8000 for more than 2 seconds
while the engine is running.

POSSIBLE CAUSES
INTERMITTENT WIRING & CONNECTORS CONDITIONS
EATX RPM SIGNAL CIRCUIT OPEN
EATX RPM SIGNAL CIRCUIT SHORTED TO GROUND
EATX RPM SIGNAL CIRCUIT SHORTED TO VOLTAGE
TRANSMISSION CONTROL MODULE
POWERTRAIN CONTROL MODULE

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.
Continue
Go To 2

331
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0725-ENGINE SPEED SENSOR CIRCUIT — Continued

TEST ACTION APPLICABILITY

2 NOTE: This code is not a Transmission Input Speed Sensor DTC All
With the DRBIIIt, Check the STARTS SINCE SET counter.
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter set at 0?
Yes → Go To 3

No → Go To 8

3 Turn ignition off to the lock position. All

Disconnect the Powertrain Control Module (PCM) harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the EATX RPM signal circuit between the TCM connector
and the PCM connector.
Is the resistance above 5.0 ohms?

Yes → Repair the open EATX RPM Signal circuit.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 4

4 Turn ignition off to the lock position. All

Disconnect the Powertrain Control Module (PCM) harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the EATX RPM Signal circuit and ground.
Is the resistance below 5.0 ohms?
Yes → Repair the EATX RPM Signal circuit for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 5

5 Turn ignition off to the lock position. All

Disconnect the PCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Measure the voltage of the EATX RPM Signal circuit in the PCM connector.
Is the voltage above 10.0 volts?
Yes → Repair the EATX RPM Signal circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 6

6 Turn the ignition off to the lock position. All

Disconnect the PCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Measure the voltage of the EATX RPM Signal circuit.
Is the voltage between 4.5 and 5.5 volts?

Yes → Replace and program the Powertrain Control Module per the
Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

332
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0725-ENGINE SPEED SENSOR CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

8 The conditions necessary to set the DTC are not present at this time. Using the All
schematics as a guide, inspect the wiring and connectors specific to this circuit.
Wiggle the wires while checking for shorts and open circuits.
Check the power and ground circuits of the Transmission Control Module.
Check the vehicles battery condition.
Were any problems found?
Yes → Repair wiring and/or connectors as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

333
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0731-GEAR RATIO ERROR IN 1ST

When Monitored and Set Condition:

P0731-GEAR RATIO ERROR IN 1ST

When Monitored: The Transmission Gear Ratio is monitored continuously while the
Transmission is in gear.
Set Condition: If the ratio of the input RPM to the output RPM does not match the
current Gear Ratio.

POSSIBLE CAUSES
RELATED DTC’S PRESENT
INTERMITTENT GEAR RATIO ERRORS
INTERNAL TRANSMISSION

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, read Transmission DTC’s All

If any of these DTC’s are present, perform their respective tests first.
Are the DTC’s P0944, P0715, P0720, or P1794 present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom. If any of these DTC’s are present, they will cause a gear
ratio error. Perform the test for Loss of Prime first if it is present.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

334
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0731-GEAR RATIO ERROR IN 1ST — Continued

TEST ACTION APPLICABILITY

3 With the DRBIIIt, perform the 1st Gear Clutch Test. Follow the instructions on the All
DRBIIIt.
Increase the throttle angle, TPS Degree, to 30° for no more than a few seconds.
CAUTION: Do not overheat the transmission.
Did the Clutch Test pass, Input Speed remain at 0?

Yes → Go To 4

No → Go To 5

4 The conditions to set this DTC are not present at this time. All
Check the gearshift linkage adjustment.
Gear ratio DTC’s can be set by problems in the Input and Output Speed Sensor
circuits. If the vehicle passes the clutch test and still sets gear ratio DTC(’s), check
the Speed Sensors for proper operation.
NOTE: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Check the Speed Sensor wiring and connectors for good connection, then perform a
wiggle test using the Transmission Simulator, Miller tool #8333 and the Electronic
Transmission Adapter kit 8333-1A.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

5 If there are no possible causes remaining, view repair. All

Repair
Repair internal transmission per the Service Information. Check
all components related to the Underdrive and L/R clutches.
Inspect the Oil Pump per the Service Information and repair or
replace as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

335
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0732-GEAR RATIO ERROR IN 2ND

When Monitored and Set Condition:

P0732-GEAR RATIO ERROR IN 2ND

When Monitored: The Transmission Gear Ratio is monitored continuously while the
Transmission is in Gear.
Set Condition: If the ratio of the input RPM to the output RPM does not match the
current Gear Ratio.

POSSIBLE CAUSES
RELATED DTC’S PRESENT
RELATED PRESSURE SWITCH DTC’S PRESENT
INTERMITTENT GEAR RATIO ERRORS
TRANSMISSION - INTERNAL

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.
Continue
Go To 2

336
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0732-GEAR RATIO ERROR IN 2ND — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, read Transmission DTC’s All
If any of these DTC’s are present, perform their respective tests first.
Are the DTC’s P0944, P0715, P0720, or P1794 present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom. If any of these DTC’s are present, they will cause a gear
ratio error. Perform the test for Loss of Prime first if it is present.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

3 With the DRBIIIt, perform the 2nd Gear Clutch Test. Follow the instructions on the All
DRBIIIt.
Increase the Throttle Angle, TPS Degree, to 30° for no more than a few seconds.
CAUTION: Do not overheat the transmission.
Did the Clutch Test pass, Input Speed remain at 0?

Yes → Go To 4
No → Go To 5

4 The conditions to set this DTC are not present at this time. All
Check the gearshift linkage adjustment.
Gear ratio DTC’s can be set by problems in the Input and Output Speed Sensor
circuits. If the vehicle passes the clutch test and still sets Gear Ratio DTC(s), check
the Speed Sensors for proper operation.
NOTE: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Check the Speed Sensor wiring and connectors for good connection, then perform a
wiggle test using the Transmission Simulator, Miller tool #8333 and the Electronic
Transmission Adapter kit 8333-1A.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

5 With the DRBIIIt, read Transmission DTC’s. All

Is the DTC P0845 and/or P0846 present also?
Yes → Replace the Solenoid/Pressure Switch Assembly per the Service
Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 6

337
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0732-GEAR RATIO ERROR IN 2ND — Continued

TEST ACTION APPLICABILITY

6 If there are no possible causes remaining, view repair. All

Repair
Repair internal transmission problem. Check all of the compo-
nents related to the Underdrive and 2/4 clutches. Inspect the Oil
Pump per the Service Information and repair or replace as
necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

338
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0733-GEAR RATIO ERROR IN 3RD

When Monitored and Set Condition:

P0733-GEAR RATIO ERROR IN 3RD

When Monitored: The Transmission Gear Ratio is monitored continuously while the
Transmission is in Gear.
Set Condition: If the ratio of the input RPM to the output RPM does not match the
current Gear Ratio.

POSSIBLE CAUSES
RELATED DTC’S PRESENT
TRANSMISSION SOLENOID PRESSURE SWITCH ASSEMBLY
INTERNAL TRANSMISSION
INTERMITTENT GEAR RATIO ERRORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.
Continue
Go To 2

339
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0733-GEAR RATIO ERROR IN 3RD — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, read Transmission DTC’s All
If any of these DTC’s are present, perform their respective tests first.
Are the DTC’s P0944, P0715, P0720, or P1794 present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom. If any of these DTC’s are present, they will cause a gear
ratio error. Perform the test for Loss of Prime first if it is present.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

3 With the DRBIIIt, perform the 3rd gear clutch test. Follow the instructions on the All
DRBIIIt.
Increase the throttle angle, TPS Degree, to 30° for no more than a few seconds.
CAUTION: Do not overheat the transmission.
Did the Clutch Test pass, Input Speed remain at 0?

Yes → Go To 4
No → Go To 5

4 The conditions to set this DTC are not present at this time. All
Check the gearshift linkage adjustment.
Gear ratio DTC’s can be set by problems in the Input and Output Speed Sensor
circuits. If the vehicle passes the clutch test and still sets Rear Ratio DTC(s), check
the Speed Sensors for proper operation.
NOTE: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Check the speed sensor wiring and connectors for good connection, then perform a
wiggle test using the Transmission Simulator, Miller tool #8333 and the Electronic
Transmission Adapter kit 8333-1A.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

5 With the DRBIIIt, read Transmission DTC’s. All

Is the DTC P0870 and/or P0871 present also?
Yes → Replace the Transmission Solenoid/Pressure Switch Assembly per
the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 6

340
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0733-GEAR RATIO ERROR IN 3RD — Continued

TEST ACTION APPLICABILITY

6 If there are no possible causes remaining, view repair. All

Repair
Repair internal transmission per the Service Information. Check
all of the components related to the Underdrive and Overdrive
clutches. Inspect the Oil Pump per the Service Information and
repair or replace as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

341
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0734-GEAR RATIO ERROR IN 4TH

When Monitored and Set Condition:

P0734-GEAR RATIO ERROR IN 4TH

When Monitored: The Transmission Gear Ratio is monitored continuously while the
Transmission is in Gear.
Set Condition: If the ratio of the input RPM to the output RPM does not match the
current Gear Ratio.

POSSIBLE CAUSES
RELATED DTC’S PRESENT
RELATED PRESSURE SWITCH DTC’S PRESENT
INTERMITTENT GEAR RATIO ERRORS
TRANSMISSION - INTERNAL

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.
Continue
Go To 2

342
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0734-GEAR RATIO ERROR IN 4TH — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, read Transmission Control Module DTC’s All
If any of these DTC’s are present, perform their respective tests first.
Are the DTC’s P0944, P0715, P0720, or P1794 present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom. If any of these DTC’s are present, they will cause a gear
ratio error. Perform the test for Loss of Prime first if it is present.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

3 With the DRBIIIt, perform the 4th gear clutch test. Follow the instructions on the All
DRBIIIt.
Increase the throttle angle, TPS Degree, to 30° for no more than a few seconds.
CAUTION: Do not overheat the transmission.
Did the Clutch Test pass, Input Speed remain at 0?

Yes → Go To 4
No → Go To 5

4 The conditions to set this DTC are not present at this time. All
Check the gearshift linkage adjustment.
Gear Ratio DTC’s can be set by problems in the Input and Output Speed Sensor
circuits. If the vehicle passes the clutch test and still sets Gear Ratio DTC(s), check
the Speed Sensors for proper operation.
NOTE: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Check the Speed Sensor wiring and connectors for good connection, then perform a
wiggle test using the Transmission Simulator, Miller tool #8333 and the Electronic
Transmission Adapter kit 8333-1A.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

5 With the DRBIIIt, read Transmission DTC’s. All

Is the DTC P0845 and/or P0846 present also?
Yes → Replace the Solenoid/Pressure Switch Assembly per the Service
Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 6

343
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0734-GEAR RATIO ERROR IN 4TH — Continued

TEST ACTION APPLICABILITY

6 If there are no possible causes remaining, view repair. All

Repair
Repair internal transmission problem. Check all of the compo-
nents related to the Overdrive and 2/4 clutches. Inspect the Oil
Pump per the Service Information and repair or replace as
necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

344
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0736-GEAR RATIO ERROR IN REVERSE

When Monitored and Set Condition:

P0736-GEAR RATIO ERROR IN REVERSE

When Monitored: The Transmission Gear Ratio is monitored continuously while the
Transmission is in Gear.
Set Condition: If the ratio of the input RPM to the output RPM does not match the
current Gear Ratio.

POSSIBLE CAUSES
RELATED DTC’S PRESENT
INTERMITTENT GEAR RATIO ERRORS
TRANSMISSION - INTERNAL

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, read Transmission DTC’s All

If any of these DTC’s are present, perform their respective tests first.
Are the DTC’s P0944, P0715, P0720, P1794, or present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom. If any of these DTC’s are present, they will cause a gear
ratio error. Perform the test for Loss of Prime first if it is present.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

345
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0736-GEAR RATIO ERROR IN REVERSE — Continued

TEST ACTION APPLICABILITY

3 With the DRBIIIt, perform the Reverse gear clutch test. Follow the instructions on All
the DRBIIIt.
Increase the throttle angle, TPS Degree, to 30° for no more than a few seconds.
CAUTION: Do not overheat the Transmission.
Did the Clutch Test pass, Input Speed remain at 0?

Yes → Go To 4

No → Go To 5

4 The conditions to set this DTC are not present at this time. All
Check the gearshift linkage adjustment.
Gear Ratio DTC’s can be set by problems in the Input and Output Speed Sensor
circuits. If the vehicle passes the clutch test and still sets Gear Ratio DTC(s), check
the Speed Sensors for proper operation.
NOTE: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Check the speed sensor wiring and connectors for good connection, then perform a
wiggle test using the Transmission Simulator, Miller tool #8333 and the Electronic
Transmission Adapter kit 8333-1A.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

5 If there are no possible causes remaining, view repair. All

Repair
Repair internal transmission problem. Check all of the compo-
nents related to the Reverse and L/R clutches. Inspect the Oil
Pump per the Service Information and repair or replace as
necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

346
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0740-TCC OUT OF RANGE

When Monitored and Set Condition:

P0740-TCC OUT OF RANGE

When Monitored: During Electronically Modulated Converter Clutch (EMCC) Operation.
Set Condition: A) Transmission must be in EMCC, with input speed > than 1750 RPM.
TCC/L-R sol achieves the maximum duty cycle & can’t pull engine RPM within 60 RPM of
input speed. B) Transmissions is in FEMCC & engine slips TCC > than 100 RPM for 10
seconds.

POSSIBLE CAUSES
RELATED DTC’S PRESENT
INTERNAL TRANSMISSION
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 Ignition on, engine not running. All

With the DRBIIIt, read Transmission DTC’s
Is the DTC P0750 and/or P0841 present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

347
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0740-TCC OUT OF RANGE — Continued

TEST ACTION APPLICABILITY

3 Ignition on, engine not running. All
With the DRBIIIt, record and erase Transmission DTCs.
Drive the vehicle until it is fully warmed up to at least 43° C or 110° F.
Perform the following steps 3 times.
With the DRBIIIt, monitor TPS degree.
Drive the vehicle to the speed of 83 Km/h or 50 MPH and allow 4th gear to engage for
at least 10 seconds.
Close the throttle, then tip back in until the throttle angle, TPS degrees, is between
25 and 29 degrees.
NOTE: If you go over 30 TPS degrees, you must back off of the throttle and
retry.
Did the TCC engage during any of the attempts?
Yes → Go To 4

No → Go To 5

4 The conditions necessary to set the DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorts and open circuits.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

5 If there are no possible causes remaining, view repair. All

Repair
Perform the Hydraulic Pressure test in the Service Information.
Repair the internal transmission components and torque conver-
tor per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

348
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0750-LR SOLENOID CIRCUIT

When Monitored and Set Condition:

P0750-LR SOLENOID CIRCUIT

When Monitored: Initially at power-up, then every 10 seconds thereafter. The solenoids
will also be tested immediately after a Gear Ratio or Pressure Switch error is detected.
Set Condition: Three consecutive solenoid continuity test failures, or one failure if a test
is run in response to a Gear Ratio or Pressure Switch error.

POSSIBLE CAUSES
RELATED RELAY DTC’S PRESENT
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
L/R SOLENOID CONTROL CIRCUIT OPEN
L/R SOLENOID CONTROL CIRCUIT SHORT TO GROUND
L/R SOLENOID CONTROL CIRCUIT SHORT TO VOLTAGE
L/R SOLENOID
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

349
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0750-LR SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

2 Ignition on, engine not running. All
With the DRBIIIt, read Transmission DTC’s
Are there any Transmission Control Relay DTC’s present?

Yes → Refer to symptom list and perform the appropriate symptom for
Transmission Control Relay related DTC’s.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, Check the STARTS SINCE SET counter for P0750. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter for P0750 set at 0?

Yes → Go To 4

No → Go To 11

4 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the DRBIIIt, actuate the L/R Solenoid.
With the Transmission Simulator, monitor the L/R Solenoid LED.
Did the L/R Solenoid LED on the Transmission Simulator blink on and off during
actuation?
Yes → Go To 5

No → Go To 6

5 If there are no possible causes remaining, view repair. All

Repair
Replace the Transmission Solenoid/Pressure Switch Assembly per
the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Measure the resistance of the L/R Solenoid Control circuit from the TCM harness
connector to the Transmission Solenoid/Pressure Switch Assembly harness connec-
tor.
Is the resistance above 5.0 ohms?
Yes → Repair the L/R Solenoid Control circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

350
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0750-LR SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Measure the resistance between ground and the L/R Solenoid Control circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the L/R Solenoid Control circuit for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Measure the voltage of the L/R Solenoid Control circuit.
Is the voltage above 0.5 volt?
Yes → Repair the L/R Solenoid Control circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 9

9 Turn the ignition off to the lock position. All

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 10

No → Repair the Transmission Control Relay Output circuit for an open

or high resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

10 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

351
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0750-LR SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

11 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

352
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0755-2/4 SOLENOID CIRCUIT

When Monitored and Set Condition:

P0755-2/4 SOLENOID CIRCUIT

When Monitored: Initially at power-up, then every 10 seconds thereafter. They will also
be tested immediately after a Gear Ratio or Pressure Switch error is detected.
Set Condition: Three consecutive Solenoid continuity test failures, or one failure if test is
run in response to a Gear Ratio or Pressure Switch error.

POSSIBLE CAUSES
RELATED RELAY DTC’S PRESENT
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
2/4 SOLENOID CONTROL CIRCUIT OPEN
2/4 SOLENOID CONTROL CIRCUIT SHORT TO GROUND
2/4 SOLENOID CONTROL CIRCUIT SHORT TO VOLTAGE
2/4 SOLENOID
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

353
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0755-2/4 SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, read Transmission Control Module DTC’s All
Are there any Transmission Control Relay DTC’s present?.

Yes → Refer to symptom list and perform the appropriate symptom for
Transmission Control Relay related DTC’s.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, Check the STARTS SINCE SET counter. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter for P0755 set at 0?

Yes → Go To 4

No → Go To 11

4 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the DRBIIIt, actuate the 2/4 Solenoid.
With the Transmission Simulator, monitor the 2/4 Solenoid LED.
Did the 2/4 Solenoid LED on the Transmission Simulator blink on and off during
actuation?

Yes → Go To 5
No → Go To 6

5 If there are no possible causes remaining, view repair. All

Repair
Replace the Transmission Solenoid/Pressure Switch Assembly per
the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the 2/4 Solenoid Control circuit from the TCM harness
connector to the Transmission Solenoid/Pressure Switch Assembly harness connec-
tor.
Is the resistance above 5.0 ohms?
Yes → Repair the 2/4 Solenoid Control circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

354
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0755-2/4 SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the 2/4 Solenoid Control circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the 2/4 Solenoid Control circuit for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and Transmission Control Relay
Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Measure the voltage of the 2/4 Solenoid Control circuit.
Is the voltage above 0.5 volt?
Yes → Repair the 2/4 Solenoid Control circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 9

9 Turn the ignition off to the lock position. All

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 10
No → Repair the Transmission Control Relay Output circuit for an open
or high resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

10 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

355
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0755-2/4 SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

11 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

356
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0760-OD SOLENOID CIRCUIT

When Monitored and Set Condition:

P0760-OD SOLENOID CIRCUIT

When Monitored: Initially at power-up, then every 10 seconds thereafter. They will also
be tested immediately after a Gear Ratio or Pressure Switch error is detected.
Set Condition: Three consecutive solenoid continuity test failures, or one failure if test is
run in response to a Gear Ratio or Pressure Switch error.

POSSIBLE CAUSES
RELATED RELAY DTC’S PRESENT
INTERMITTENT WIRING AND CONNECTORS
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
OD SOLENOID CONTROL CIRCUIT OPEN
OD SOLENOID CONTROL CIRCUIT SHORT TO GROUND
OD SOLENOID CONTROL CIRCUIT SHORT TO VOLTAGE
OD SOLENOID
TRANSMISSION CONTROL MODULE

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

357
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0760-OD SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, read Transmission Control Module DTC’s All
Are there any Transmission Control Relay DTC’s present?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, Check the STARTS SINCE SET counter for P0760. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter for P0760 set at 0?

Yes → Go To 4

No → Go To 11

4 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the Transmission Simulator, monitor the OD Solenoid LED.
With the DRBIIIt, actuate the OD Solenoid.
Did the OD Solenoid LED on the Transmission Simulator blink on and off during
actuation?

Yes → Go To 5
No → Go To 6

5 If there are no possible causes remaining, view repair. All

Repair
Replace the Transmission Solenoid/Pressure Switch Assembly per
the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the OD Solenoid Control circuit from the TCM harness
connector to the Transmission Solenoid/Pressure Switch Assembly harness connec-
tor.
Is the resistance above 5.0 ohms?
Yes → Repair the OD Solenoid Control circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

358
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0760-OD SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the OD Solenoid Control circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the OD Solenoid Control circuit for a short to ground.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Measure the voltage of the OD Solenoid Control circuit.
Is the voltage above 0.5 volt?
Yes → Repair the OD Solenoid Control circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 9

9 Turn the ignition off to the lock position. All

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 10
No → Repair the Transmission Control Relay Output circuit for an open
or high resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

10 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

359
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0760-OD SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

11 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

360
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0765-UD SOLENOID CIRCUIT

When Monitored and Set Condition:

P0765-UD SOLENOID CIRCUIT

When Monitored: Initially at power-up, then every 10 seconds thereafter. They will also
be tested immediately after a Gear Ratio or Pressure Switch error is detected.
Set Condition: Three consecutive Solenoid continuity test failures, or one failure if test is
run in response to a Gear Ratio or Pressure Switch error.

POSSIBLE CAUSES
RELATED RELAY DTC’S PRESENT
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
UD SOLENOID CONTROL CIRCUIT OPEN
UD SOLENOID CONTROL CIRCUIT SHORT TO GROUND
UD SOLENOID CONTROL CIRCUIT SHORT TO VOLTAGE
UD SOLENOID
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

361
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0765-UD SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, read Transmission Control Module DTC’s All
Are there any Transmission Control Relay DTC’s present?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, Check the STARTS SINCE SET counter. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter for P0765 set at 0?

Yes → Go To 4

No → Go To 11

4 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the DRBIIIt, actuate the UD Solenoid.
With the Transmission Simulator, monitor the UD Solenoid LED.
Did the UD Solenoid LED on the Transmission Simulator blink on and off?

Yes → Go To 5
No → Go To 6

5 If there are no possible causes remaining, view repair. All

Repair
Replace Transmission Solenoid/Pressure Switch Assembly per the
Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the UD Solenoid Control circuit from the TCM harness
connector to the Transmission Solenoid/Pressure Switch Assembly harness connec-
tor.
Is the resistance above 5.0 ohms?
Yes → Repair the UD Solenoid Control circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

362
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0765-UD SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the UD Solenoid Control circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the UD Solenoid Control circuit for a short to ground.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Connect a jumper wire between the Fused B+ circuits and Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Note: Check connectors - Clean/repair as necessary.
Measure the voltage of the UD Solenoid Control circuit.
Is the voltage above 0.5 volt?
Yes → Repair the UD Solenoid Control circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 9

9 Turn the ignition off to the lock position. All

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and Transmission Control Relay
Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 10
No → Repair the Transmission Control Relay Output circuit for an open
or high resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

10 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

363
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0765-UD SOLENOID CIRCUIT — Continued

TEST ACTION APPLICABILITY

11 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

364
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0841-LR PRESSURE SWITCH SENSE CIRCUIT

When Monitored and Set Condition:

P0841-LR PRESSURE SWITCH SENSE CIRCUIT

When Monitored: Whenever the engine is running.
Set Condition: The appropriate DTC is set if one of the Pressure Switches are open or
closed at the wrong time in a given gear .

POSSIBLE CAUSES
LOSS OF PRIME DTC P0944 PRESENT
TRANSMISSION CONTROL RELAY DTCS PRESENT
TCM AND WIRING
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
L/R PRESSURE SWITCH SENSE CIRCUIT OPEN
L/R PRESSURE SWITCH SENSE CIRCUIT SHORT TO GROUND
L/R PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

365
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0841-LR PRESSURE SWITCH SENSE CIRCUIT — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, check for other Transmission DTC’s. All
Is the DTC P0944 present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, read Transmission DTC’s All

Are there any Transmission Control Relay DTC’s present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 4

4 With the DRBIIIt, Check the STARTS SINCE SET counter for P0841. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

Yes → Go To 5
No → Go To 11

5 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
On the Transmission Simulator select L/R on the Pressure Switch selector switch.
With the DRBIIIt, monitor the L/R Pressure Switch state while pressing the
Pressure Switch Test button on the Transmission Simulator.
Did the Pressure Switch state change from OPEN to CLOSED when the test button
was pressed?

Yes → Replace the Transmission Solenoid/Pressure Switch Assembly per

the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 6

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the L/R Pressure Switch Sense circuit from the TCM
harness connector to the Transmission Solenoid/Pressure Switch Assembly harness
connector.
Is the resistance above 5.0 ohms?
Yes → Repair the L/R Pressure Switch Sense circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

366
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0841-LR PRESSURE SWITCH SENSE CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the L/R Pressure Switch Sense circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the L/R Pressure Switch circuit for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and Transmission Control Relay
Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the L/R Pressure Switch Sense circuit.
Is the voltage above 0.5 volt?
Yes → Repair the L/R Pressure Switch Sense circuit for a short to
voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 9

9 Turn the ignition off to the lock position. All

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and Transmission Control Relay
Output circuit in the Transmission Control Relay connector.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit in the Solenoid/Pressure Switch Assembly harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 10
No → Repair the Transmission Control Relay Output circuit for an open
or high resistance. If the fuse is open make sure to check for a
short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

10 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

367
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0841-LR PRESSURE SWITCH SENSE CIRCUIT — Continued

TEST ACTION APPLICABILITY

11 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

368
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0845-2/4 HYDRAULIC PRESSURE TEST FAILURE

When Monitored and Set Condition:

P0845-2/4 HYDRAULIC PRESSURE TEST FAILURE

When Monitored: In any forward gear with engine speed above 1000 RPM shortly after
a shift and every minute thereafter.
Set Condition: After a shift into a forward gear, with engine speed > 1000 RPM, the TCM
momentarily turns on element pressure to the clutch ckts that don’t have pressure to
identify the correct pressure sw closes. If the pressure sw does not close 2 times the code
sets.

POSSIBLE CAUSES
LOSS OF PRIME P0944 PRESENT
RELATED DTC’S PRESENT
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
2/4 PRESSURE SWITCH SENSE CIRCUIT OPEN
2/4 PRESSURE SWITCH SENSE CIRCUIT SHORT TO GROUND
2/4 PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE
INTERNAL TRANSMISSION
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

369
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0845-2/4 HYDRAULIC PRESSURE TEST FAILURE — Continued

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, check for other Transmission DTCs. All

Is the DTC P0944 present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, read Transmission DTC’s. All

Is the DTC P0732, P0734 and/or P0846 present also?

Yes → Repair internal transmission as necessary. Refer to the Service

Information for the proper repair procedure for components
related to the OD clutch.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 4

4 With the DRBIIIt, Check the STARTS SINCE SET counter for P0845. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

Yes → Go To 5
No → Go To 12

370
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0845-2/4 HYDRAULIC PRESSURE TEST FAILURE — Continued

TEST ACTION APPLICABILITY

5 Turn the ignition off to the lock position. All
CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the Transmission Simulator, select 92/49 on the Pressure Switch rotary switch.
With the DRBIIIt, monitor the 2/4 Pressure Switch state while pressing the Pressure
Switch Test button on the Transmission Simulator.
Wiggle the wiring leading to the TCM while pressing the button.
Did the 2-4 Pressure Switch state change to closed and remain closed while wiggling
the wires?

Yes → Go To 6
No → Go To 7

6 If there are no possible causes remaining, view repair. All

Repair
Disassemble and inspect the Valve Body per the Service Informa-
tion and repair or replace as necessary. If there are no problems
found in the Valve Body, replace the Transmission Solenoid/
Pressure Switch Assembly per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

7 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the 2/4 Pressure Switch Sense circuit from the TCM
harness connector to the Transmission Solenoid/Pressure Switch Assembly harness
connector.
Is the resistance above 5.0 ohms?

Yes → Repair the 2/4 Pressure Switch Sense circuit or an open.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the 2/4 Pressure Switch Sense circuit.
Is the resistance below 5.0 ohms?
Yes → Repair the 2/4 Pressure Switch Sense circuit for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 9

371
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0845-2/4 HYDRAULIC PRESSURE TEST FAILURE — Continued

TEST ACTION APPLICABILITY

9 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the 2/4 Pressure Switch Sense circuit.
Is the voltage above 0.5 volt?

Yes → Repair the 2/4 Pressure Switch Sense circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 10

10 Turn the ignition off to the lock position. All

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and Transmission Control Relay
Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 11
No → Repair the Transmission Control Relay Output circuit for an open
or high resistance. If the fuse is open make sure to check for a
short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

11 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

12 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

372
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0846-2/4 PRESSURE SWITCH SENSE CIRCUIT

When Monitored and Set Condition:

P0846-2/4 PRESSURE SWITCH SENSE CIRCUIT

When Monitored: Whenever the engine is running.
Set Condition: The appropriate DTC is set if one of the Pressure Switches are open or
closed at the wrong time in a given gear .

POSSIBLE CAUSES
TRANSMISSION RELAY DTC’S PRESENT
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
2/4 PRESSURE SWITCH SENSE CIRCUIT OPEN
2/4 PRESSURE SWITCH SENSE CIRCUIT SHORT TO GROUND
2/4 PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE
2/4 PRESSURE SWITCH
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

373
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0846-2/4 PRESSURE SWITCH SENSE CIRCUIT — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, read Transmission DTC’s All
Are there any Transmission Control Relay DTC’s present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, Check the STARTS SINCE SET counter. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less for P0846?

Yes → Go To 4

No → Go To 11

4 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay. This will prevent the vehicle from
being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the Transmission Simulator, select 2/4 on the Pressure Switch selector switch.
With the DRBIIIt, monitor the 2/4 Pressure Switch state while pressing the Pressure
Switch Test button on the Transmission Simulator.
Did the Pressure Switch state change from OPEN to CLOSED when the test button
was pressed?
Yes → Go To 5

No → Go To 6

5 If there are no possible causes remaining, view repair. All

Repair
Replace Transmission Solenoid/Pressure Switch Assembly per the
Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the 2/4 Pressure Switch Sense circuit from the TCM
harness connector to the Transmission Solenoid/Pressure Switch Assembly harness
connector.
Is the resistance above 5.0 ohms?
Yes → Repair the 2/4 Pressure Switch Sense circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

374
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0846-2/4 PRESSURE SWITCH SENSE CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the 2/4 Pressure Switch Sense circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the 2/4 Pressure Switch Sense circuit for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the 2/4 Pressure Switch Sense circuit.
Is the voltage above 0.5 volt?
Yes → Repair the 2/4 Pressure Switch Sense circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 9

9 Turn the ignition off to the lock position. All

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 10
No → Repair the Transmission Control Relay Output circuit for an open
or high resistance. If the fuse is open make sure to check for a
short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

10 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

375
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0846-2/4 PRESSURE SWITCH SENSE CIRCUIT — Continued

TEST ACTION APPLICABILITY

11 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

376
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0870-OD HYDRAULIC PRESSURE TEST FAILURE

When Monitored and Set Condition:

P0870-OD HYDRAULIC PRESSURE TEST FAILURE

When Monitored: In any forward gear with engine speed above 1000 RPM shortly after
a shift and every minute thereafter.
Set Condition: After a shift into a forward gear, with engine speed > 1000 RPM, the TCM
momentarily turns on element pressure to the clutch ckts that don’t have pressure to
identify the correct pressure sw closes. If the pressure sw does not close 2 times the code
sets

POSSIBLE CAUSES
LOSS OF PRIME DTC P0944 PRESENT
RELATED DTC’S PRESENT
INTERMITTENT WIRING AND CONNECTORS
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
OD PRESSURE SWITCH SENSE CIRCUIT OPEN
OD PRESSURE SWITCH SENSE CIRCUIT SHORT TO GROUND
OD PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE
INTERNAL TRANSMISSION
TRANSMISSION CONTROL MODULE

377
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0870-OD HYDRAULIC PRESSURE TEST FAILURE — Continued

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, check for other Transmission DTCs. All

Is the DTC P0944 present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, read Transmission DTC’s. All

Is the DTC P0733 and/or P0871 present also?

Yes → Replace the Transmission or Solenoid/Pressure Switch Assembly

per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 4

4 With the DRBIIIt, Check the STARTS SINCE SET counter for P0870. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

Yes → Go To 5
No → Go To 12

378
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0870-OD HYDRAULIC PRESSURE TEST FAILURE — Continued

TEST ACTION APPLICABILITY

5 Turn the ignition off to the lock position. All
CAUTION: Remove the Starter Relay. This will prevent the vehicle from
being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
NOTE: Check connectors - Clean/repair as necessary.
With the Transmission Simulator, select 9OD9 on the Pressure Switch rotary switch.
With the DRBIIIt, monitor the OD Pressure Switch state while pressing the
Pressure Switch Test button on the Transmission Simulator.
Wiggle the wires leading to the TCM while pressing the test button.
Did the O/D Pressure Switch state change to closed and remain closed while wiggling
the wires?
Yes → Go To 6

No → Go To 7

6 If there are no possible causes remaining, view repair. All

Repair
Disassemble and inspect the Valve Body per the Service Informa-
tion and repair or replace as necessary. If no problems are found in
the Valve Body, replace the Transmission Solenoid/Pressure
Switch Assembly per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

7 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the OD Pressure Switch Sense circuit from the TCM
harness connector to the Transmission Solenoid/Pressure Switch Assembly harness
connector.
Is the resistance above 5.0 ohms?

Yes → Repair the O/D Pressure Switch Sense circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the OD Pressure Switch Sense circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the OD Pressure Switch Sense circuit for a short to

ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 9

379
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0870-OD HYDRAULIC PRESSURE TEST FAILURE — Continued

TEST ACTION APPLICABILITY

9 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the OD Pressure Switch Sense circuit.
Is the voltage above 0.5 volt?

Yes → Repair OD Pressure Switch Sense circuit for a short to voltage.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 10

10 Turn the ignition off to the lock position. All

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 11
No → Repair the Transmission Control Relay Output circuit for an open
or high resistance. If the fuse is open make sure to check for a
short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

11 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

12 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

380
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0871-OD PRESSURE SWITCH SENSE CIRCUIT

When Monitored and Set Condition:

P0871-OD PRESSURE SWITCH SENSE CIRCUIT

When Monitored: Whenever the engine is running.
Set Condition: The appropriate DTC is set if one of the Pressure Switches are open or
closed at the wrong time in a given gear.

POSSIBLE CAUSES
TRANSMISSION CONTROL RELAY DTCS PRESENT
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
O/D PRESSURE SWITCH SENSE CIRCUIT OPEN
O/D PRESSURE SWITCH SENSE CIRCUIT SHORT TO GROUND
O/D PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE
O/D PRESSURE SWITCH
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

381
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0871-OD PRESSURE SWITCH SENSE CIRCUIT — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, read Transmission DTC’s All
Are there any Transmission Control Relay DTC’s present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, Check the STARTS SINCE SET counter. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less for P0871?

Yes → Go To 4

No → Go To 11

4 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay. This will prevent the vehicle from
being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
On the Transmission Simulator, select OD on the Pressure Switch selector switch.
With the DRBIIIt, monitor the OD Pressure Switch state while pressing the
Pressure Switch Test button on the Transmission Simulator.
Did the Pressure Switch state change from OPEN to CLOSED when the test button
was pressed?
Yes → Go To 5

No → Go To 6

5 If there are no possible causes remaining, view repair. All

Repair
Replace Transmission Solenoid/Pressure Switch Assembly per the
Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the O/D Pressure Switch Sense circuit from the TCM
harness connector to the Transmission Solenoid/Pressure Switch Assembly harness
connector.
Is the resistance above 5.0 ohms?
Yes → Repair the O/D Pressure Switch Sense circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

382
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0871-OD PRESSURE SWITCH SENSE CIRCUIT — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the O/D Pressure Switch Sense circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the O/D Pressure Switch circuit for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the O/D Pressure Switch Sense circuit.
Is the voltage above 0.5 volt?
Yes → Repair the O/D Pressure Switch Sense circuit for a short to
voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 9

9 Turn the ignition off to the lock position. All

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 10

No → Repair the Transmission Control Relay Output circuit for an open

or high resistance. If the fuse is open make sure to check for a
short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

10 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

383
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0871-OD PRESSURE SWITCH SENSE CIRCUIT — Continued

TEST ACTION APPLICABILITY

11 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

384
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0884-POWER UP AT SPEED

When Monitored and Set Condition:

P0884-POWER UP AT SPEED
When Monitored: When Transmission Control Module powers up.
Set Condition: This DTC will set if the TCM powers up and senses the vehicle in a valid
forward gear (no PRNDL DTCs) with a output speed above 800 RPM (approximately
32Km/h or 20 MPH).

POSSIBLE CAUSES
POWER UP AT SPEED

TEST ACTION APPLICABILITY

1 This DTC is set when the TCM is initialized while the vehicle is moving down the All
road in a valid forward gear.
Check all of the Fused B+, Fused Ignition Switch Output, and Ground circuits to the
TCM for an intermittent open or short to ground.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

385
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0888-RELAY OUTPUT ALWAYS OFF

When Monitored and Set Condition:

P0888-RELAY OUTPUT ALWAYS OFF

When Monitored: Continuously
Set Condition: This code is set when less than 3 volts are present at the transmission
control relay output circuits at the Transmission Control Module when the TCM is
energizing the relay.

POSSIBLE CAUSES
FUSED B+ CIRCUIT OPEN
TRANSMISSION CONTROL RELAY GROUND CIRCUIT OPEN
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, Check the STARTS SINCE SET counter for P0888. All
Note: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter set at 0?

Yes → Go To 3

No → Go To 5

386
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0888-RELAY OUTPUT ALWAYS OFF — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off to the lock position. All
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Fused B+ circuit in the
Transmission Control Relay connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 4

No → Repair the Fused B+ circuit for an open or high resistance. If the

fuse is open make sure to check for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

4 Turn the ignition off to the lock position. All

Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Using a 12-volt test light connected to 12-volts, check the Transmission Control Relay
Ground circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?
Yes → Test Complete.

No → Repair the Transmission Control Relay Ground circuit for an open

or high resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

5 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

387
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0890-SWITCHED BATTERY

When Monitored and Set Condition:

P0890-SWITCHED BATTERY
When Monitored: Ignition key is turned from the OFF position to RUN position and/or
ignition key is turned from the CRANK position to RUN position.
Set Condition: This DTC is set if the Transmission Control Module senses voltage on any
of the Pressure Switch Inputs prior to the TCM energizing the Transmission Control Relay.

POSSIBLE CAUSES
2/4 PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE
L/R PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 With the DRBIIIt, Check the STARTS SINCE SET counter for P0890. All
Note: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter for P0890 set at 0?

Yes → Go To 3

No → Go To 5

388
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0890-SWITCHED BATTERY — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the 2/4 Pressure Switch Sense circuit.
Is the voltage above 0.5 volt?

Yes → Repair the 2/4 Pressure Switch Sense circuit for a short to voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 4

4 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the L/R Pressure Switch Sense circuit.
Is the voltage above 0.5 volt?
Yes → Repair the L/R Pressure Switch Sense circuit for a short to
voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

5 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

389
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0891-TRANSMISSION RELAY ALWAYS ON

When Monitored and Set Condition:

P0891-TRANSMISSION RELAY ALWAYS ON

When Monitored: When the ignition is turned from the OFF position to the RUN position
and/or the ignition is turned from the CRANK position to RUN position.
Set Condition: This DTC is set if the Transmission Control Module senses greater than
3.0 volts at the Transmission Control Relay Output terminal of the TCM prior to the TCM
energizing the Transmission Control Relay.

POSSIBLE CAUSES
INTERMITTENT WIRING AND CONNECTORS
TRANSMISSION CONTROL RELAY STUCK CLOSED
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT SHORT TO VOLTAGE
TRANSMISSION RELAY CONTROL CIRCUIT SHORT TO VOLTAGE
TRANSMISSION CONTROL MODULE

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

390
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0891-TRANSMISSION RELAY ALWAYS ON — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, check the STARTS SINCE SET counter for P0891. All
Note: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter set to 0?

Yes → Go To 3
No → Go To 7

3 Turn the ignition off to the lock position. All

Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the Fused B+ circuit and the Transmission Control
Relay Output Circuit in the Transmission Control Relay.
Is the resistance above 5.0 ohms?

Yes → Go To 4

No → Replace the Transmission Control Relay.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

4 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Measure the voltage of the Transmission Control Relay Output circuit in the
Solenoid/Pressure Switch Assembly harness connector.
Is the voltage above 0.5 volt?
Yes → Repair the Transmission Control Relay Output circuit for a short
to voltage
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 5

5 Turn the ignition off to the lock position. All

Remove the Transmission Control Relay from the PDC.
Ignition on, engine not running.
Note: Check connectors - Clean/repair as necessary.
Measure the voltage of the Transmission Relay Control circuit in the PDC connector.
Is the voltage above 0.5 volt?

Yes → Repair Transmission Relay Control Circuit for a short to voltage.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 6

6 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

391
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0891-TRANSMISSION RELAY ALWAYS ON — Continued

TEST ACTION APPLICABILITY

7 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

392
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0897-WORN OUT/BURNT TRANSAXLE FLUID

When Monitored and Set Condition:

P0897-WORN OUT/BURNT TRANSAXLE FLUID

When Monitored: With each transition from full Torque Convertor to partial Torque
Convertor engagement for A/C bump prevention.
Set Condition: When vehicle shudder is detected during partial engagement (PEMCC).

POSSIBLE CAUSES
WORN OUT/ BURNT TRANSMISSION FLUID

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

393
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0897-WORN OUT/BURNT TRANSAXLE FLUID — Continued

TEST ACTION APPLICABILITY

2 Turn the ignition off. All
Remove the Transmission Oil Pan and Oil Filter per the Service Information.
Install a new Transmission Oil Filter per Service Information.
Reinstall Transmission Oil Pan, and refill with new Transmission Fluid per the
Service Information.
Note: The Transmission Cooler must be flushed before prodceeding.
Start the engine, check and adjust the Transmission Fluid Level per Service
Information.
Allow the engine to idle for 10 minutes, in Park.
Flush the Transmission Oil Cooler per the Service Information.
Turn the ignition off.
Drain and refill the Transmission Fluid.
Flush the Transmission Oil Cooler again.
Start the engine, check and adjust the Transmission Fluid Level per Service
Information.
With the DRBIIIt, perform a Battery Disconnect.
Note: This must be done to re enable EMCC during an A/C Clutch engage-
ment.
The vehicle may exhibit intermittent shudder during the first few hundred miles.
Note: The oil will gradually penetrate the TCC friction material and the
shudder should disappear.
Erase the DTC and return the vehicle to the customer.
Did the Code reset or does the vehicle still shudder after a few thousand miles?

Yes → Replace the Torque Convertor per the Service Information.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

394
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P0944-LOSS OF PRIME

When Monitored and Set Condition:

P0944-LOSS OF PRIME
When Monitored: If the transmission is slipping in any forward gear and the pressure
switches are not indicating pressure, a loss of prime test is run.
Set Condition: If the Trans. begins to slip in a forward gear & the press. switch(s) that
should be closed are open a loss of prime test begins. Available elements are turned on by
the TCM to see if pump prime exists.The code sets if no pressure switches respond.

POSSIBLE CAUSES
SHIFT LEVER POSITION
PLUGGED TRANSMISSION OIL FILTER
TRANSMISSION OIL PUMP
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.
Continue
Go To 2

395
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P0944-LOSS OF PRIME — Continued

TEST ACTION APPLICABILITY

2 Place the gear selector in park. All
Start the engine.
NOTE: The TRANS TEMP DEG must be at least 43° C or 110° F before
performing the following steps.
The Transmission must be at operating temperature prior to checking pressure. A
cold Transmission will give higher readings.
Place the Transmission in Reverse.
With the DRBIIIt, observe the Transmission Pressure Switch states.
Are any of the Pressure Switches closed?

Yes → Go To 3

No → Go To 5

3 The conditions necessary to set this DTC are not present at this time. All
Test drive the vehicle. Allow the Transmission to shift through all gears and ranges.
Did you experience a delayed engagement and/or a no drive condition?
Yes → Go To 5
No → Go To 4

4 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?
Yes → Repair as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

5 With the DRBIIIt, perform a Shift Lever Position test. Follow the instructions on the All
DRBIIIt.
Did the Shift Lever Position Test pass?

Yes → Go To 6

No → Refer to symptom list and perform test for DTC P0706.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 Remove and inspect the Transmission Oil Pan and Transmission Oil Filter per the All
Service Information.
Does the Transmission Oil Pan contain excessive debris and/or is the Oil Filter
plugged?

Yes → Repair the cause of the plugged Transmission Oil Filter. Refer to
the Service Information for the proper repair procedure.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

396
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0944-LOSS OF PRIME — Continued

TEST ACTION APPLICABILITY

7 If there are no possible causes remaining, view repair. All

Repair
Replace the Transmission Oil Pump per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

397
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P0992- 2-4/OD HYDRAULIC PRESSURE TEST FAILURE

When Monitored and Set Condition:

P0992- 2-4/OD HYDRAULIC PRESSURE TEST FAILURE

When Monitored: In any forward gear with engine speed above 1000 RPM shortly after
a shift and every minute thereafter.
Set Condition: After a shift into a forward gear, with engine speed > 1000 RPM, the TCM
momentarily turns on element pressure to the clutch ckts that don’t have pressure to
identify the correct pressure sw closes. If the pressure sw does not close 2 times the code
sets.

POSSIBLE CAUSES
CONDITION P0992 PRESENT

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

398
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P0992- 2-4/OD HYDRAULIC PRESSURE TEST FAILURE — Continued

TEST ACTION APPLICABILITY

2 NOTE: The vehicle must be driven to set this DTC, the transmission must be All
warm or hot with the Engine RPM above 1000 RPM.
This DTC is an indicator of a 2/4 and/or O/D Hydraulic Pressure Switch DTC’s
present. Perform the tests for P0870 and/or P0845 to determine which switch is
failing.
If there are no possible causes remaining, view repair.

Repair
Refer to the Transmission category and perform the appropriate
symptom for P0870 and/or P0845.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

399
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P1652-SERIAL COMMUNICATION LINK MALFUNCTION

When Monitored and Set Condition:

P1652-SERIAL COMMUNICATION LINK MALFUNCTION

When Monitored: Continuously with engine running.
Set Condition: The DTC sets in approximately 20 seconds if no BUS messages are
received by the TCM.

POSSIBLE CAUSES
NO COMMUNICATION WITH MIC
NO COMMUNICATION WITH PCM
INTERMITTENT WIRING AND CONNECTORS
TRANSMISSION CONTROL MODULE

TEST ACTION APPLICABILITY

1 With the DRBIIIt, erase TCM DTC’s. All
Note: Erase P0700 DTC in the PCM to turn the MIL light off after making
transmission repairs.
Start the engine in park.
Did the DTC reset after the engine was started?
Yes → Go To 2

No → Go To 5

2 Ignition on, engine not running. All

With the DRBIIIt, attempt communication with the MIC
Can you communicate with the MIC?
Yes → Go To 3

No → Refer to the Communication category for the related symptom(s).

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

3 Ignition on, engine not running. All

With the DRBIIIt, select the following screens in order: 9BODY9 9MIC9 9MONITOR
DISPLAY9 9PCI BUS ENGINE INFO9.
Does the DRBIIIt, read 9NO RESPONSE9 from any of the listed PCM monitors?
Yes → Refer to Communication Category for the related symptom(s).
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 4

400
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P1652-SERIAL COMMUNICATION LINK MALFUNCTION — Continued

TEST ACTION APPLICABILITY

4 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

5 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

401
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P1684-BATTERY WAS DISCONNECTED

When Monitored and Set Condition:

P1684-BATTERY WAS DISCONNECTED

When Monitored: Whenever the key is in the Run/Start position.
Set Condition: This code is set whenever Transmission Control Module (TCM) is
disconnected from battery power B+ or ground. It will also be set during the DRBIIIt
Quick Battery Disconnect procedure.

POSSIBLE CAUSES
QUICK LEARN WAS PERFORMED
RECENT BATTERY DISCONNECTION
TCM WAS REPLACED OR DISCONNECTED
INTERMITTENT WIRING AND CONNECTORS
FUSED B+ CIRCUIT TO TCM OPEN
GROUND CIRCUIT OPEN

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.
Continue
Go To 2

402
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P1684-BATTERY WAS DISCONNECTED — Continued

TEST ACTION APPLICABILITY

2 Turn ignition off to the lock position. All
Disconnect the TCM harness connector.
Ignition on, engine not running.
Measure the voltage of the Fused B+ circuit in the TCM harness connector.
Is the voltage below 10.0 volts?

Yes → Go To 3

No → Go To 5

3 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Fused B+ circuit in the TCM
harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 4
No → Repair the Fused B+ circuit for an open or high resistance. If the
fuse is open make sure to check for a short to ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

4 Turn ignition off to the lock position. All

Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Using a 12-volt test light connected to 12-volts, check all the ground circuits in the
TCM harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the light illuminate brightly at all the ground circuits?
Yes → Test Complete.

No → Repair the Ground circuit(s) as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

5 Has the battery been disconnected, lost it’s charge, or been replaced recently? All

Yes → This is the cause of the DTC. Erase the DTC and return the
vehicle to the customer.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 6

6 Has the Quick Learn procedure been performed? All

Yes → This is the cause of the DTC. Erase the DTC and return the
vehicle to the customer.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

403
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P1684-BATTERY WAS DISCONNECTED — Continued

TEST ACTION APPLICABILITY

7 Has the TCM been replaced or disconnected? All

Yes → Replacing or disconnecting the TCM will set this DTC. Erase the
DTC and return the vehicle to the customer.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 8

8 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

404
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P1687-NO COMMUNICATION WITH THE MIC

When Monitored and Set Condition:

P1687-NO COMMUNICATION WITH THE MIC

When Monitored: Continuously with engine running.
Set Condition: The code sets in approximately 25 seconds if no BUS messages are
received from the MIC.

POSSIBLE CAUSES
OTHER BUS PROBLEMS PRESENT
INTERMITTENT WIRING AND CONNECTORS
MIC - NO COMMUNICATION
TRANSMISSION CONTROL MODULE

TEST ACTION APPLICABILITY

1 With the DRBIIIt, Check the STARTS SINCE SET counter for P1687. All
Note: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter set at 0?
Yes → Go To 2
No → Go To 5

2 With the DRBIIIt, check all of the other modules on the vehicle for evidence of a All
vehicle bus problem.
Bus related DTC’s in other modules point to an overall vehicle bus problem. Other
symptoms such as a customer complaint of intermittent operation of bus controlled
features also indicate a bus problem.
Does the PRNDL display indicate 9No Bus9 or is there any evidence of an overall
vehicle bus problem?

Yes → Refer to the Communications category and perform the appropri-

ate symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

3 Ignition on, engine not running. All

With the DRBIIIt, clear all DTC’s.
Start the engine in park.
With the DRBIIIt, read the MIC DTC’s.
Can the DRBIIIt communicate with the MIC?

Yes → Go To 4

No → Refer to the Communication category and perform the appropri-

ate symptom related to No Response to MIC.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

405
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P1687-NO COMMUNICATION WITH THE MIC — Continued

TEST ACTION APPLICABILITY

4 Ignition on, engine not running. All
With the DRBIIIt, erase TCM DTC’s.
Start the engine in park.
With the DRBIIIt, read Transmission DTC’s.
Is the DTC, P1687- No Communication with the MIC, present?

Yes → Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

5 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

406
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P1694-BUS COMMUNICATION WITH ENGINE MODULE

When Monitored and Set Condition:

P1694-BUS COMMUNICATION WITH ENGINE MODULE

When Monitored: Continuously with ignition key on.
Set Condition: If no bus messages are received from the Powertrain Control Module for
10 seconds.

POSSIBLE CAUSES
NO COMMUNICATION WITH PCM
OTHER BUS PROBLEMS PRESENT
INTERMITTENT WIRING AND CONNECTORS
TRANSMISSION CONTROL MODULE

TEST ACTION APPLICABILITY

1 With the DRBIIIt, Check the STARTS SINCE SET counter for P1694. All
Note: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter for P1694 set to 0?
Yes → Go To 2
No → Go To 5

2 With the DRBIIIt, check all of the other modules on the vehicle for evidence of a All
vehicle bus problem.
Bus related DTC’s in other modules point to an overall vehicle bus problem. Other
symptoms such as a customer complaint of intermittent operation of bus controlled
features also indicate a bus problem.
Does the PRNDL display indicate 9No Bus9 or is there any evidence of an overall
vehicle bus problem?

Yes → Refer to the Communication category and perform the appropri-

ate symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

3 Ignition on, engine not running. All

With the DRBIIIt, attempt to communicate with the Powertrain Control Module
(PCM).
Can the DRBIIIt communicate with the PCM?
Yes → Go To 4
No → Refer to the Communication category and perform the appropri-
ate symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

407
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P1694-BUS COMMUNICATION WITH ENGINE MODULE — Continued

TEST ACTION APPLICABILITY

4 Ignition on, engine not running. All
With the DRBIIIt, erase TCM DTC’s.
Start the engine in park.
With the DRBIIIt, read Transmission DTC’s.
Did the DTC, P1694, return?

Yes → Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 5

5 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

408
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P1775-SOLENOID SWITCH VALVE LATCHED IN TCC POSITION

When Monitored and Set Condition:

P1775-SOLENOID SWITCH VALVE LATCHED IN TCC POSITION

When Monitored: During an attempted shift into 1st gear.
Set Condition: This DTC is set if three unsuccessful attempts are made to shift into 1st
gear in one given ignition start.

POSSIBLE CAUSES
RELATED DTC P0841 PRESENT
L/R PRESSURE SWITCH
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
L/R PRESSURE SWITCH SENSE CIRCUIT OPEN
L/R PRESSURE SWITCH SENSE CIRCUIT SHORT TO GROUND
L/R PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

409
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P1775-SOLENOID SWITCH VALVE LATCHED IN TCC POSITION —

Continued
TEST ACTION APPLICABILITY
2 With the DRBIIIt, check for other Transmission DTC’s All
Is the DTC P0841 present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, Check the STARTS SINCE SET counter for P1775. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

Yes → Go To 4

No → Go To 10

4 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the FWD Adapter Cable
kit, Miller tool #8333-1.
Ignition on, engine not running.
With the DRBIIIt, monitor the L/R Pressure Switch state while pressing the
Pressure Switch Test button on the Transmission Simulator.
With the Transmission Simulator, select the L/R on the Pressure Switch selector.
While observing the LR pressure switch state with the DRBIIIt, depress the
Pressure Switch Test button.
Did the L/R Pressure Switch state change from OPEN to CLOSED when the test
button was pressed?
Yes → Inspect the Solenoid Switch Valve in the Valve Body per the
Service Information and repair or replace as necessary. If no
problems are found in Valve Body, replace the Transmission
Solenoid/Pressure Switch Assembly per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 5

5 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the L/R Pressure Switch Sense circuit from the TCM
harness connector to the Transmission Solenoid/Pressure Switch Assembly harness
connector.
Is the resistance above 5.0 ohms?
Yes → Repair the L/R Pressure Switch Sense circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 6

410
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P1775-SOLENOID SWITCH VALVE LATCHED IN TCC POSITION —

Continued
TEST ACTION APPLICABILITY
6 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the L/R Pressure Switch Sense circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the L/R Pressure Switch Sense circuit for a short to
ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

7 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the L/R Pressure Switch Sense circuit.
Is the voltage above 0.5 volt?
Yes → Repair the L/R Pressure Switch Sense circuit for a short to
voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between Fused B+ circuit and the Transmission Control Relay
Output circuit.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit in the Solenoid/Pressure Switch Assembly harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?
Yes → Go To 9

No → Repair the Transmission Control Relay Output circuit for an open

or high resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

411
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P1775-SOLENOID SWITCH VALVE LATCHED IN TCC POSITION —

Continued
TEST ACTION APPLICABILITY
9 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

10 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Test drive the vehicle.
Did you experience any 2nd gear launches or no TCC engagement?

Yes → Inspect the Valve Body for signs of a stuck valve or other problem
in the SSV area. If no problems are found, replace the Solenoid/
Pressure Switch Assembly. If excessive debris is present in the
Pan or Valve Body, repair cause of the debris as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

412
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P1776-SOLENOID SWITCH VALVE LATCHED IN LR POSITION

When Monitored and Set Condition:

P1776-SOLENOID SWITCH VALVE LATCHED IN LR POSITION

When Monitored: Continuously when doing partial or full EMCC (PEMCC or FEMCC).
Set Condition: This DTC will set if the TCM senses the L/R Pressure Switch closing while
performing PEMCC or FEMCC or after two unsuccessful attempts to perform PEMCC or
FEMCC.

POSSIBLE CAUSES
RELATED DTC P0841 PRESENT
L/R PRESSURE SWITCH
TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN
L/R PRESSURE SWITCH SENSE CIRCUIT OPEN
L/R PRESSURE SWITCH SENSE CIRCUIT SHORT TO GROUND
L/R PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

413
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P1776-SOLENOID SWITCH VALVE LATCHED IN LR POSITION —

Continued
TEST ACTION APPLICABILITY
2 With the DRBIIIt, check for other Transmission DTCs All
Is the DTC P0841 present also?

Yes → Refer to the Transmission category and perform the appropriate

symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 3

3 With the DRBIIIt, Check the STARTS SINCE SET counter for P1776. All
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

Yes → Go To 4

No → Go To 10

4 Turn the ignition off to the lock position. All

CAUTION: Remove the Starter Relay. This will prevent the vehicle from
being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the FWD Adapter Cable
kit, Miller tool #8333-1.
Ignition on, engine not running.
On the Transmission Simulator select L/R on the Pressure Switch selector switch.
With the DRBIIIt, monitor the L/R Pressure Switch state while pressing the
Pressure Switch Test button on the Transmission Simulator.
Did the Pressure Switch state change from OPEN to CLOSED when the test button
was pressed?
Yes → Inspect the Solenoid Switch Valve in the Valve Body per the
Service Information and repair or replace as necessary. If no
problems are found in Valve Body, replace the Transmission
Solenoid/Pressure Switch Assembly per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 5

5 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the L/R Pressure Switch Sense circuit from the TCM
harness connector to the Transmission Solenoid/Pressure Switch Assembly harness
connector.
Is the resistance above 5.0 ohms?
Yes → Repair the L/R Pressure Switch Sense circuit for an open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 6

414
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P1776-SOLENOID SWITCH VALVE LATCHED IN LR POSITION —

Continued
TEST ACTION APPLICABILITY
6 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the L/R Pressure Switch Sense circuit.
Is the resistance below 5.0 ohms?

Yes → Repair the L/R Pressure Switch Sense circuit for a short to
ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

7 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the L/R Pressure Switch Sense circuit.
Is the voltage above 0.5 volts?
Yes → Repair the L/R Pressure Switch Sense circuit for a short to
voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 8

8 Turn the ignition off to the lock position. All

Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 9

No → Repair the Transmission Control Relay Output circuit for an open

or high resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

9 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

415
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P1776-SOLENOID SWITCH VALVE LATCHED IN LR POSITION —

Continued
TEST ACTION APPLICABILITY
10 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Test drive the vehicle.
Did you experience any 2nd gear launches or no TCC engagement?

Yes → Inspect the Valve Body for signs of a stuck valve or other problem
in the SSV area. If no problems are found, replace the Solenoid/
Pressure Switch Assembly. If excessive debris is present in the
Pan or Valve Body, repair the cause of debris as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

416
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P1790-FAULT IMMEDIATELY AFTER SHIFT

When Monitored and Set Condition:

P1790-FAULT IMMEDIATELY AFTER SHIFT

When Monitored: After a speed ratio error is stored.
Set Condition: This code is set if the associated speed ratio code is stored within 1.3
seconds after a shift.

POSSIBLE CAUSES
CONDITION P1790 PRESENT

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 This DTC is set along with a gear ratio DTC. Perform the appropriate test for the All
Gear Ratio DTC stored.
NOTE: Check 1 trip failures if there are no Gear Ratio DTC’s current.
If there are no possible causes remaining, view repair.
Repair
Refer to the Transmission category and perform the appropriate
symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

417
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
P1793-TRD LINK COMMUNICATION ERROR

When Monitored and Set Condition:

P1793-TRD LINK COMMUNICATION ERROR

When Monitored: The transmission controller pulses the 12 volt TRD signal from the
PCM to ground, during torque managed shifts with the throttle angle above 54 degrees.
The TRD system is also tested whenever the vehicle is stopped and the engine speed is at
idle.
Set Condition: This code is set when the Transmission Control Module (TCM) sends two
subsequent torque reduction messages to the Powertrain Control Module (PCM) via the
TRD link circuit and does not receive a confirmation from the PCM over the communica-
tion bus.

POSSIBLE CAUSES
RELATED DTC’S PRESENT
TORQUE MANAGEMENT REQUEST SENSE CIRCUIT OPEN
TORQUE MANAGEMENT REQUEST SENSE SHORT TO GROUND
TORQUE MANAGEMENT REQUEST SENSE CIRCUIT SHORT TO VOLTAGE
POWERTRAIN CONTROL MODULE
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

418
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

P1793-TRD LINK COMMUNICATION ERROR — Continued

TEST ACTION APPLICABILITY

2 With the DRBIIIt, read Transmission DTC’s. All
Are any of the following DTCs P1694, P0731, P0732, P0733, P0734, P0736 present
also?

Yes → If any of these codes are present, disregard the P1793 DTC and
refer to the Transmission category and perform the appropriate
symptom.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

3 With the DRBIIIt, Check the STARTS SINCE SET counter. All
Note: This counter only applies to the last DTC set.
Is the STARTS SINCE SET equal to 0?

Yes → Go To 4

No → Go To 9

4 Turn the ignition off to the lock position. All

Disconnect the PCM harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Torque Management Request Sense circuit from the
TCM harness connector to the PCM harness connector.
Is the resistance above 5.0 ohms?
Yes → Repair the Torque Management Request Sense circuit for an
open.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 5

5 Turn the ignition off to the lock position. All

Disconnect the PCM harness connector.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Torque Management Request Sense
circuit.
Is the resistance below 5.0 ohms?
Yes → Repair Torque Management Request Sense circuit for a short to
ground.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 6

6 Turn the ignition off to the lock position. All

Disconnect the TCM harness connector.
Ignition on, engine not running.
Measure the voltage of the Torque Management Request Sense circuit.
Is the voltage above 10.5 volts?
Yes → Repair Torque Management Request Sense circuit for a short to
voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 7

419
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P1793-TRD LINK COMMUNICATION ERROR — Continued

TEST ACTION APPLICABILITY

7 Turn the ignition off to the lock position. All
Disconnect the TCM harness connector.
Ignition on, engine not running.
Measure the voltage of the Torque Management Request Sense circuit in the TCM
harness connector.
Is the voltage above 7.0 volts?

Yes → Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 8

8 If there are no possible causes remaining, view repair. All

Repair
Replace and program the Powertrain Control Module per the
Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

9 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

420
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P1794-SPEED SENSOR GROUND ERROR

When Monitored and Set Condition:

P1794-SPEED SENSOR GROUND ERROR

When Monitored: The transmission gear ratio is monitored continuously while the
transmission is in gear.
Set Condition: After a TCM reset in neutral and Input/Output speed ratio equals a ratio
of input to output of 2.5 to 1.

POSSIBLE CAUSES
SPEED SENSOR GROUND CIRCUIT OPEN
TRANSMISSION CONTROL MODULE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

2 Start the engine in park. All

With the DRBIIIt, observe the Input and Output Speed Sensor readings.
Is the Output Speed Sensor reading twice the Input Speed Sensor reading?

Yes → Go To 3

No → Go To 6

421
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P1794-SPEED SENSOR GROUND ERROR — Continued

TEST ACTION APPLICABILITY

3 Turn the ignition off to the lock position. All
CAUTION: Remove the Starter Relay. This will prevent the vehicle from
being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
Using the Transmission Simulator, set the selector switch to the 3000/1250 position.
Turn the Input/Output switch to ON.
With the DRBIIIt, read the Input and Output Speed Sensor RPM.
Does the Input Speed read 3000 RPM and the Output Speed read 1250 RPM within
50 RPM?

Yes → Go To 5

No → Go To 4

4 Turn the ignition off to the lock position. All

Disconnect Input and Output Speed Sensor harness connectors.
Disconnect the TRS harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Speed Sensor Ground circuit from the TCM harness
connector to the Input and Output Speed Sensor harness connectors.
Is the resistance above 5.0 ohms on either Speed Sensor Ground circuit?
Yes → Repair the Speed Sensor Ground circuit for an open or high
resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 5

5 Using the schematics as a guide, inspect the wiring and connectors. Repair as All
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

Repair
Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIIIt PERFORM QUICK LEARN.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6 The conditions necessary to set this DTC are not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

422
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
P1797-MANUAL SHIFT OVERHEAT

When Monitored and Set Condition:

P1797-MANUAL SHIFT OVERHEAT

When Monitored: Whenever engine is running and transmission is in the AutoStick
mode.
Set Condition: If the engine temperature exceeds 124° C or 255° F or the transmission
temperature exceeds 135° C or 275° F while in AutoStick mode. Note: Aggressive driving
or driving in low for extended periods of time in AutoStickt mode will set this DTC.

POSSIBLE CAUSES
MANUAL SHIFT OVERHEAT

TEST ACTION APPLICABILITY

1 NOTE: Low fluid level can be the cause of many Transmission problems. If All
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIIIt, read the engine DTC’s. Check and repair all engine DTC’s prior
to performing Transmission Symptom Diagnostics.
With the DRBIIIt, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

Continue
Go To 2

423
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

P1797-MANUAL SHIFT OVERHEAT — Continued

TEST ACTION APPLICABILITY

2 This is an informational DTC only. All
Check the Engine and Transmission Cooling Systems for proper operation.
Check the Radiator Cooling Fan operation.
Check the Transmission Cooling Fan operation if equipped.
Check the Transmission Fluid Level. Make sure it is not overfilled.
NOTE: Aggressive driving or driving in low for extended periods of time in
Autostickt mode will set this DTC.
With the DRBIIIt, check the EATX EVENT DATA to help identify the conditions in
which the DTC was set.
Were there any problems found?

Yes → Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Test Complete.

424
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
*BACKUP LAMPS COME ON WHILE SHIFTER IS NOT IN REVERSE
POSITION

POSSIBLE CAUSES
BACKUP LAMPS ALWAYS ON
BACKUP LAMP SUPPLY CIRCUIT SHORT TO VOLTAGE
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
Firmly apply brakes.
Place the shift lever in the position which causes the Backup Lamps to come on other
than Reverse.
Do the Backup Lamps come on with the shift lever not in the Reverse position?
Yes → Go To 2

No → Go To 4

2 Ignition on, engine not running. All

Place the Shift Lever in the position that causes the Backup Lamps to come on other
than Reverse.
Disconnect the TRS harness connector.
NOTE: This will cause a DTC P0706 and possibly other DTC’s to be stored in
the TCM. They must be erased before returning the vehicle to the customer.
Did the Backup Lamps go out when the TRS harness connector was disconnected?

Yes → Replace the Transmission Range Sensor per the Service Informa-
tion.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.
No → Go To 3

3 Turn the ignition off to the lock position. All

Disconnect the Transmission TRS harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Measure the voltage of the Back-up Lamp Supply circuit in the TCM harness
connector.
Is the voltage above 0.5 volt?

Yes → Repair the Backup Lamp Supply circuit for a short to voltage.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.
No → Test Complete.

425
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

*BACKUP LAMPS COME ON WHILE SHIFTER IS NOT IN REVERSE

POSITION — Continued
TEST ACTION APPLICABILITY
4 The condition is not present at this time. All
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
Were there any problems found?

Yes → Repair as necessary.

Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.
No → Test Complete.

426
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
*BACKUP LAMPS INOPERATIVE

POSSIBLE CAUSES
OPEN LEFT BACKUP LAMP BULB
OPEN RIGHT BACKUP LAMP BULB
BACKUP LAMP GROUND CIRCUIT OPEN
BACKUP LAMP SUPPLY CIRCUIT OPEN
FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
BACKUP LAMP SUPPLY CIRCUIT SHORT TO GROUND
TRANSMISSION RANGE SENSOR
INTERMITTENT WIRING AND CONNECTORS

TEST ACTION APPLICABILITY

1 Ignition on, engine not running. All
Place foot firmly on brake pedal.
Place the shift lever in the reverse position.
Do either of the Backup Lamps work?
Yes → Go To 2

No → Go To 3

2 The condition is not present at this time. All

Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
Were there any problems found?

Yes → Repair as necessary.

Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.
No → Test Complete.

3 Remove the left Backup Lamp bulb. All

Measure the resistance of the Backup Lamp bulb.
Is the resistance above 5.0 ohms?

Yes → Replace the Backup Lamp bulb.

Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

No → Go To 4

4 Remove the right Backup Lamp bulb. All

Measure the resistance of the Backup Lamp bulb.
Is the resistance above 5.0 ohms?
Yes → Replace the Backup Lamp bulb.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.
No → Go To 5

427
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

*BACKUP LAMPS INOPERATIVE — Continued

TEST ACTION APPLICABILITY

5 Turn the ignition off to the lock position. All
CAUTION: Remove the Starter Relay. This will prevent the vehicle from
being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the FWD Adapter Cable
kit, Miller tool #8333-1A.
Ignition on, engine not running.
Press the 9Reverse Light Test9 button on the Transmission Simulator while observing
the backup lamps.
Do either of the back-up lamps come on?

Yes → Go To 6

No → Go To 7

6 If there are no possible causes remaining, view repair. All

Repair
Replace Transmission Range Sensor per the Service Information.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

7 Remove the Backup Lamp bulb. All

Using a 12-volt test light connected to 12-volts, check the Backup Lamp Ground
circuit in the Backup Lamp socket.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?
Yes → Go To 8
No → Repair the Backup Lamp Ground circuit for an open or high
resistance.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

8 Turn the ignition off to the lock position. All

Remove the Backup Lamp bulb.
Disconnect the Transmission TRS harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Backup Lamp Supply circuit from the Backup Lamp
Socket to the TRS harness connector.
Is the resistance above 5.0 ohms?
Yes → Repair the Backup Lamp Supply circuit for an open.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

No → Go To 9

428
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

*BACKUP LAMPS INOPERATIVE — Continued

TEST ACTION APPLICABILITY

9 Turn the ignition off to the lock position. All
Disconnect the Transmission TRS harness connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Fused Ignition Switch
Output circuit in the TRS harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

Yes → Go To 10
No → Repair the Fused Ignition Switch Output circuit for an open. If
the fuse is open make sure to check for a short to ground.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

10 Turn ignition off to the lock position. All

Remove the Backup Lamp bulb.
Disconnect the Transmission TRS harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Backup Lamp Supply circuit.
Is the resistance below 5.0 ohms?
Yes → Repair Backup Lamp Supply circuit for a short to ground. Check
the fuse and replace if necessary.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

No → Test Complete.

429
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
*CHECKING PARK/NEUTRAL SWITCH OPERATION

POSSIBLE CAUSES
P/N POSITION SWITCH SENSE CIRCUIT OPEN
P/N POSITION SWITCH SENSE CIRCUIT SHORTED TO GROUND
TRANSMISSION RANGE SENSOR
PCM - P/N POSITION SWITCH

TEST ACTION APPLICABILITY

1 Turn the ignition on. All
With the DRBIIIt, read the Park/Neutral Position Switch input state.
While moving the gear selector through all gear positions, Park to 1 and back to Park,
watch the DRBIIIt display.
Did the DRBIIIt display show P/N and D/R in the correct gear positions?
Yes → Test Complete.

No → Go To 2

2 Turn the ignition off. All

Disconnect the PCM harness connectors.
Disconnect the Transmission Range Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the P/N Position Switch Sense circuit.
Is the resistance below 5.0 ohms?

Yes → Go To 3
No → Repair the P/N Position Switch Sense circuit for an open.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

3 Turn the ignition off. All

Disconnect the PCM harness connectors.
Disconnect the Transmission Range Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the P/N Position Switch Sense circuit.
Is the resistance above 100k ohms?

Yes → Go To 4

No → Repair the P/N Position Switch Sense circuit for a short to ground.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

430
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

*CHECKING PARK/NEUTRAL SWITCH OPERATION — Continued

TEST ACTION APPLICABILITY

4 Turn the ignition off. All
Disconnect the PCM harness connectors.
Move the Gear selector through all gear positions, from Park to 1st and back.
While moving the gear selector through each gear, measure the resistance between
ground and the P/N Position Switch Sense circuit.
Did the resistance change from above 10.0 ohms to below 10.0 ohms?

Yes → Go To 5

No → Replace the Transmission Range Sensor.

Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

5 If there are no possible causes remaining, view repair. All

Repair
Replace and program the Powertrain Control Module per the
Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

431
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
*INCORRECT TRANSMISSION FLUID LEVEL

POSSIBLE CAUSES
INCORRECT FLUID LEVEL

TEST ACTION APPLICABILITY

1 The transmission must be above 70 degree F. prior to checking fluid level. Adjusting All
fluid level on a cold transmission will result in an overfilled transmission.
Check the transmission fluid level per the service information.
Is the fluid level OK?
Yes → Test Complete.

No → Adjust fluid level. Repair cause of incorrect fluid level.

Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

432
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
*NO SPEEDOMETER OPERATION

POSSIBLE CAUSES
NO SPEEDOMETER OPERATION

TEST ACTION APPLICABILITY

1 With the DRBIIIt, check the pinion factor setting in the TCM. All
Is the pinion factor missing or set incorrectly?

Yes → One possible cause is the pinion factor is not set or is set
incorrectly in the TCM.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

433
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
*TRANSMISSION NOISY WITH NO DTC’S PRESENT

POSSIBLE CAUSES
INCORRECT FLUID LEVEL
INTERNAL TRANSMISSION PROBLEM - NOISY
INTERNAL TRANSMISSION PROBLEM - NOISY WHILE STANDING STILL

TEST ACTION APPLICABILITY

1 Check the Transmission Fluid Level per the Service Information. All
Is the fluid level OK?

Yes → Go To 2
No → Adjust fluid level and repair cause of incorrect fluid level.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

2 Place vehicle on hoist. All

WARNING: BE SURE TO KEEP HANDS AND FEET CLEAR OF ROTATING
WHEELS.
Run vehicle on hoist under conditions necessary to duplicate the noise.
NOTE: It may be necessary to test drive the vehicle to duplicate the noise.
Using Chassis Ears or other suitable listening device, verify the source of the noise.
Is the noise coming from the transmission?

Yes → Go To 3
No → Test Complete.

3 With the shift lever in neutral, raise the engine speed and listen to the noise. All
NOTE: THE RADIO MUST BE TURNED OFF. Alternator noise can come
through the speakers and be misinterpreted as Transmission Pump Whine.
This can happen even with the volume turned down.
Does the noise get louder or change pitch while the engine speed is changing?
Yes → Go To 4

No → Go To 5

4 If there are no possible causes remaining, view repair. All

Repair
Repair internal transmission problem as necessary. Inspect all of
the transmission components for signs of wear. If no problems
found, replace the Transmission oil pump..
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

5 If there are no possible causes remaining, view repair. All

Repair
Repair internal transmission problem as necessary. Inspect all of
the transmission components for signs of wear. Pay particular
attention to bearings, pinion gears, etc. Repair or replace as
necessary.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

434
bY dR.dEaDhEaD
 TRANSMISSION - 42RLE

Symptom:
*TRANSMISSION SHIFTS EARLY WITH NO DTC’S

POSSIBLE CAUSES
BUS PROBLEMS
CHECK FOR INTERMITTENT WIRING & CONNECTORS
COLD TRANSMISSION

TEST ACTION APPLICABILITY

1 Using the DRBIIIt, check all other Modules for signs of a PCI bus problem such as All
bus related DTC’s and/or communication problems.
Check and diagnose all 1 trip failures as a hard code.
Although it takes two occurences of a missed TRD link message to set the DTC
P1793, one missed message will cause the transmission to short shift until the next
start up. If the vehicle has any indications of a bus problem, the bus must be repaired
first
Do any of the other modules show signs of a bus problem?
Yes → Repair the PCI bus problem.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Go To 2

2 NOTE: If the Transmission shifts too early when the Transmission is cold, All
this is a normal condition. The software is designed to protect the Trans-
mission from high torque and/or high RPM shifts during cold operation.
Did the problem occur when the Transmission temperature was cold?
Yes → This is a normal condition.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.
No → Go To 3

3 The conditions necessary to set the DTC are not present at this time. Using the All
schematics as a guide, inspect the wiring and connectors. Wiggle the wires while
checking for shorts and open circuits.
Although it takes two occurences of a missed TRD link message to set the DTC
P1793, one missed message will cause the transmission to short shift until the next
start up. If the vehicle has any indications of a bus problem, the bus must be repaired
first
Were any problems found?

Yes → Repair wiring and/or connector as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No → Test Complete.

435
bY dR.dEaDhEaD
TRANSMISSION - 42RLE

Symptom:
*TRANSMISSION SIMULATOR 8333 WILL NOT POWER UP

TEST ACTION APPLICABILITY

1 NOTE: If the Transmission Simulator Miller tool #8333 will not power up, All
this is a symptom of the Transmission Relay being open, such as Limp-in,
and/or this also could be a indication of the Transmission Simulator not
installed correctly on the vehicle.
NOTE: Check the Simulator ground cable connection.
NOTE: Check all Transmission Simulator harness connections.
Repair these symptoms before having the Transmission Simulator Miller Tool #8333
repaired.
Continue
Test Complete.

436
bY dR.dEaDhEaD
 VEHICLE THEFT/SECURITY

Symptom List:
ANTENNA FAILURE
COP FAILURE
EEPROM FAILURE
INTERNAL FAULT
RAM FAILURE
SERIAL LINK INTERNAL FAULT
STACK OVERFLOW FAILURE

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be ANTENNA FAILURE.

When Monitored and Set Condition:

ANTENNA FAILURE
When Monitored: Every 250 milliseconds with the ignition on.
Set Condition: The SKIM’s microcontroller determines that an antenna circuit fault has
occurred for 2.0 consecutive seconds.

COP FAILURE
When Monitored: With the ignition on.
Set Condition: The COP timer is not reset by the micro controller every 65.5 milliseconds.

EEPROM FAILURE
When Monitored: With the ignition on.
Set Condition: When the value written to EEPROM memory does not equal the value
read back after the write operation.

INTERNAL FAULT
When Monitored: With the ignition on.
Set Condition: The SKIM has detected a fault during an internal self test.

RAM FAILURE
When Monitored: With the ignition on.
Set Condition: The RAM fails a test that checks the RAM’s ability to retain memory.

SERIAL LINK INTERNAL FAULT

When Monitored: With the ignition on.
Set Condition: The SKIM fails an internal J1850 communication self test.

STACK OVERFLOW FAILURE

When Monitored: With the ignition on.
Set Condition: The micro controller has exceeded its stack space limit.
437
bY dR.dEaDhEaD
VEHICLE THEFT/SECURITY

ANTENNA FAILURE — Continued

POSSIBLE CAUSES
SKIM INTERNAL DTC FAILURE

TEST ACTION APPLICABILITY

1 Note: This trouble code indicates an internal SKIM fault. All
With the DRBIIIt, read and record the SKIM DTCs and then erase the SKIM DTCs
Perform 5 ignition key cycles, leaving the ignition key on for a minimum of 90 seconds
per cycle.
With the DRBIIIt , read the SKIM DTCs.
Did the same SKIM DTC return?

Yes → Replace and program the Sentry Key Immobilizer Module in

accordance with the Service Information.
Perform SKIS VERIFICATION.
No → Test Complete.

438
bY dR.dEaDhEaD
 VEHICLE THEFT/SECURITY

Symptom List:
PCM STATUS FAILURE
SERIAL LINK EXTERNAL FAULT

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be PCM STATUS FAILURE.

When Monitored and Set Condition:

PCM STATUS FAILURE

When Monitored: With the ignition on.
Set Condition: This DTC exists when a PCM STATUS message was not received from the
PCM for at least 20.0 consecutive seconds.

SERIAL LINK EXTERNAL FAULT

When Monitored: At ignition on, after ignition on during any rolling code handshake that
occurs with the PCM due to a SKIM reset, or during SECRET KEY transfers to the PCM.
Set Condition: When the SKIM does not receive an expected PCI BUS message trans-
mission acknowledgement from the PCM after 3 transmit attempts.

POSSIBLE CAUSES
INTERMITTENT WIRING HARNESS PROBLEM
WIRING HARNESS INSPECTION
SKIM/PCM

TEST ACTION APPLICABILITY

1 NOTE: Ensure the PCM has proper power and ground connections before All
continuing.
With the DRBIIIt, read and record the SKIM DTCs then erase the SKIM DTCs.
Turn the ignition off.
Wait 2 minutes.
Turn the ignition on.
With the DRBIIIt, read the SKIM DTCs.
Does the DRBIIIt display the DTC that was previously erased?
Yes → Go To 2

No → Go To 4

439
bY dR.dEaDhEaD
VEHICLE THEFT/SECURITY

PCM STATUS FAILURE — Continued

TEST ACTION APPLICABILITY

2 Turn the ignition off. All
NOTE: Visually inspect the related wiring harness and CCD/PCI Bus
(whichever applicable) circuits. Look for any chafed, pierced, pinched, or
partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
Note: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?

Yes → Repair as necessary.

Perform SKIS VERIFICATION.

No → Go To 3

3 NOTE: Before proceeding it will be necessary to obtain the SKIM PIN. All
Turn the ignition on.
With the DRBIIIt, display and erase all PCM and SKIM DTC’s.
Perform 5 ignition key cycles, leaving the ignition key on for a minimum of 90 seconds
per cycle.
With the DRBIIIt, read the SKIM DTCs.
Does the code appear?
Yes → Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform SKIS VERIFICATION.
No → Test Complete.

4 Turn the ignition off. All

Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
Note: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?
Yes → Repair wiring harness/connectors as necessary.
Perform SKIS VERIFICATION.
No → Test Complete.

440
bY dR.dEaDhEaD
 VEHICLE THEFT/SECURITY

Symptom List:
ROLLING CODE FAILURE
VIN MISMATCH

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be ROLLING CODE FAILURE.

When Monitored and Set Condition:

ROLLING CODE FAILURE

When Monitored: At ignition on, after ignition on during any rolling code handshake that
occurs with the PCM due to a SKIM or PCM reset.
Set Condition: When a PCM STATUS message with a Valid Key status is not received by
the SKIM within 3.5 seconds of transmitting the last Valid Key Code message to the PCM.

VIN MISMATCH
When Monitored: With the ignition on.
Set Condition: When the VIN received from the PCM does not match the VIN stored in
the SKIM’s EEPROM.

POSSIBLE CAUSES
VERIFYING PCM VIN
REPLACE SKIM AND CHECK DTC’S
INTERMITTENT WIRING HARNESS PROBLEM
PCM

TEST ACTION APPLICABILITY

1 With the DRBIIIt, erase the SKIM DTCs. All
Turn the ignition off.
Wait 10 seconds.
Turn the ignition on and wait 2 minutes.
With the DRBIIIt, read the SKIM DTCs.
Does the DRBIIIt display the DTC that was previously erased?

Yes → Go To 2

No → Go To 4

441
bY dR.dEaDhEaD
VEHICLE THEFT/SECURITY

ROLLING CODE FAILURE — Continued

TEST ACTION APPLICABILITY

2 Turn the ignition on. All
With the DRBIIIt, select Engine system from the main menu.
Display and record the Vehicle Identification Number.
NOTE: Ensure that a VIN has been programmed into the PCM. If a VIN is not
displayed, attempt to program the PCM with the correct vehicle VIN before
continuing.
Does the VIN recorded from the PCM match the VIN of the vehicle?

Yes → Go To 3
No → Perform the PCM replaced to update the VIN in the PCM.
Perform SKIS VERIFICATION.

3 Turn the ignition off. All

Replace and program the Sentry Key Immobilizer Module in accordance with the
Service Information.
Turn the ignition on.
With the DRBIIIt, display and clear all PCM and SKIM DTC’s.
Perform 5 ignition key cycles leaving the ignition key on for 90 seconds per cycle.
With the DRBIIIt, check for SKIM DTCs.
Does the DRBIIIt display the same DTC?
Yes → Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform SKIS VERIFICATION.
No → The repair is complete.
Perform SKIS VERIFICATION.

4 Turn the ignition off. All

Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
Note: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?
Yes → Repair wiring harness/connectors as necessary.
Perform SKIS VERIFICATION.

No → Test Complete.

442
bY dR.dEaDhEaD
 VEHICLE THEFT/SECURITY

Symptom List:
TRANSPONDER COMMUNICATION FAILURE
TRANSPONDER CYCLIC REDUNDANCY CHECK (CRC) FAILURE
TRANSPONDER ID MISMATCH
TRANSPONDER RESPONSE MISMATCH

Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be TRANSPONDER COMMUNICA-
TION FAILURE.

When Monitored and Set Condition:

TRANSPONDER COMMUNICATION FAILURE

When Monitored: At ignition on and during Key Programming Mode.
Set Condition: When the SKIM does not receive a transponder response after 8 consec-
utive transponder read attempts within 2.0 seconds.

TRANSPONDER CYCLIC REDUNDANCY CHECK (CRC) FAILURE

When Monitored: At ignition on and during Key Programming Mode.
Set Condition: When 5 consecutive transponder signal transmissions are sent to the
SKIM with the correct message format but with invalid data.

TRANSPONDER ID MISMATCH
When Monitored: At ignition on and during Key Programming Mode.
Set Condition: When the transponder ID read by the SKIM does not match any of the
transponder ID’s stored in the SKIM’s memory.

TRANSPONDER RESPONSE MISMATCH

When Monitored: At ignition on and during Key Programming Mode.
Set Condition: When the transponder’s crypto algorithm result fails to match the SKIM’s
result.

POSSIBLE CAUSES
CHECKING MULTIPLE KEY OPERATION
SKIM
INTERMITTENT WIRING HARNESS PROBLEM
REPLACE IGNITION KEY

443
bY dR.dEaDhEaD
VEHICLE THEFT/SECURITY

TRANSPONDER COMMUNICATION FAILURE — Continued

TEST ACTION APPLICABILITY

1 With the DRBIIIt, read and record the SKIM DTCs. All
With the DRBIIIt, erase the SKIM DTCs.
NOTE: Perform the following test several times to ensure the DTC is
current.
Turn the ignition off.
Wait 10 seconds.
Turn the ignition on.
With the DRBIIIt, read the SKIM DTCs.
Does the DRBIIIt display the DTC that was previously erased?

Yes → Go To 2

No → Go To 7

2 Are there multiple vehicle ignition keys available? All

Yes → Go To 3
No → Go To 4

3 NOTE: Perform the following steps using one of the vehicle ignition keys. All
When finished, repeat the procedure using each of the other vehicle keys
one at a time.
With the DRBIIIt, erase the SKIM DTCs.
Turn the ignition off.
Wait 10 seconds.
Turn the ignition on.
With the DRBIIIt, read the SKIM DTCs.
Is the DTC present for all ignition keys?
Yes → Replace and program the Sentry Key Immobilizer Module in
accordance with the Service Information.
Perform SKIS VERIFICATION.

No → Replace the ignition key(s) that cause the SKIM DTC.

Perform SKIS VERIFICATION.

4 With the DRBIIIt, attempt to reprogram the ignition keys to the SKIM. All
With the DRBIIIt, erase the SKIM DTCs.
Wait 10 seconds.
Turn the ignition on.
With the DRBIIIt, read the SKIM DTCs.
Does the DTC set again?

Yes → Go To 5
No → Test Complete.

5 Replace the ignition key with a new key. All

With the DRBIIIt, program the new ignition key to the SKIM.
With the DRBIIIt, erase the SKIM DTCs.
Turn the ignition off.
Wait 10 seconds.
Turn the ignition on.
With the DRBIIIt, read the SKIM DTCs.
Does the DTC set again?
Yes → Go To 6

No → Test Complete.

444
bY dR.dEaDhEaD
 VEHICLE THEFT/SECURITY

TRANSPONDER COMMUNICATION FAILURE — Continued

TEST ACTION APPLICABILITY

6 If there are no possible causes remaining, view repair. All

Repair
Replace and program the Sentry Key Immobilizer Module in
accordance with the Service Information.
Perform SKIS VERIFICATION.

7 Turn the ignition off. All

Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
Note: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?

Yes → Repair wiring harness/connectors as necessary.

Perform SKIS VERIFICATION.
No → Test Complete.

445
bY dR.dEaDhEaD
VERIFICATION TESTS

Verification Tests
42RLE TRANSMISSION VERIFICATION TEST - VER 1 APPLICABILITY
1. Connect the DRBIIIt to the Data Link Connector (DLC). All
2. Reconnect any disconnected components.
3. With the DRBIIIt, erase all Transmission DTC’s, also erase the PCM DTC’s.
4. NOTE: Erase DTC P0700 in the PCM to turn the Malfunction Indicator Lamp (MIL)
off after making Transmission repairs.
5. With the DRBIIIt, display Transmission Temperature. Start and run the engine until the
Transmission Temperature is HOT - above 43° C or 110° F.
6. Check the Transmission Fluid and adjust if necessary. Refer to the Service information for
the Fluid Fill procedure.
7. NOTE: If the Transmission Control Module or the Transmission has been repaired
or replaced it is necessary to perform the DRBIIIt Quick Learn Procedure and reset
the (Pinion Factor(
8. Road test the vehicle. With the DRBIIIt, monitor the engine RPM. Make 15 to 20 1-2, 2-3,
3-4 upshifts. Perform these shifts from a standing start to 45 MPH with a constant throttle
opening of 20 to 25 degrees.
9. Below 25 MPH, make 5 to 8 wide open throttle kickdowns to 1st gear. Allow at least 5 seconds
each in 2nd and 3rd gear between each kickdown.
10. For a specific DTC, drive the vehicle to the Symptom’s When Monitored/When Set
conditions to verify the DTC repair.
11. If equipped with AutoStickt, up-shift and down-shift several times using the AutoStickt
feature during the road test.
12. NOTE: Use the EATX OBDII Task Manager to run Good Trip time in each gear, this
will confirm the repair and to ensure that the DTC has not re-matured.
13. Check for Diagnostic Trouble Codes (DTC’s) during the road test. If a DTC sets during the
road test , return to the Symptom list and perform the appropriate Symptom.
Were there any Diagnostic Trouble Codes (DTCs) set during the road test?

Yes → Refer to the Symptom List for appropriate Symptom(s).

No → Repair is complete.

BODY VERIFICATION TEST - VER 1 APPLICABILITY

1. Disconnect all jumper wires and reconnect all previously disconnected components and All
connectors.
2. NOTE: If the SKIM or PCM was replaced, refer to the service information for
proper programming procedures.
3. NOTE: If the MIC was replaced, configure new cluster with Tire Size, Axle, T-Case
Type, and EQ Setting.
4. Ensure all accessories are turned off and the battery is fully charged.
5. With the DRBIIIt, record and erase all DTC’s from ALL modules. Start and run the engine
for 2 minutes. Operate all functions of the system that caused the original concern.
6. Turn the ignition off and wait 5 seconds. Turn the ignition on and using the DRBIIIt, read
DTC’s from ALL modules.
Are any DTCs present or is the original condition still present?

Yes → Repair is not complete, refer to the appropriate symptom.

No → Repair is complete.

446
bY dR.dEaDhEaD
 VERIFICATION TESTS

Verification Tests — Continued

POWERTRAIN VERIFICATION TEST VER - 1 APPLICABILITY

1. NOTE: After completing the Powertrain Verification Test the Transmission Verifi- All
cation Test must be performed.
2. NOTE: If the PCM has been replaced and the correct VIN and mileage have not
been programmed, a DTC will set in the ABS Module, Airbag Module and the SKIM.
3. NOTE: If the vehicle is equipped with a Sentry Key Immobilizer System, Secret Key
data must be updated. Refer to the Service Information for the PCM, SKIM and the
Transponder (ignition key) for programming information.
4. Inspect the vehicle to ensure that all components related to the repair are properly installed
and connected.
5. Inspect the engine oil for fuel contamination. Replace the oil and filter as necessary.
6. Attempt to start the engine.
7. If the No Start condition is still present, refer to the symptom list and perform the diagnostic
testing as necessary. Refer to any Technical Service Bulletins that may apply.
8. Run the engine for one warm-up cycle to verify operation.
9. With the DRBIIIt, confirm that no DTCs or Secondary Indicators are present and that all
components are functioning properly.
Are any DTCs or symptoms remaining?
Yes → Check for any related Technical Service Bulletins and/or refer to the
appropriate Symptom list (Diagnostic Procedure).

No → Repair is complete.

POWERTRAIN VERIFICATION TEST VER - 2 APPLICABILITY

1. NOTE: After completing the Powertrain Verification Test the Transmission Verifi- All
cation Test must be performed.
2. NOTE: If the PCM has been replaced and the correct VIN and mileage have not
been programmed, a DTC will set in the ABS Module, Airbag Module and the SKIM.
3. NOTE: If the vehicle is equipped with a Sentry Key Immobilizer System, Secret Key
data must be updated. Refer to the Service Information for the PCM, SKIM and the
Transponder (ignition key) for programming information.
4. Inspect the vehicle to ensure that all components related to the repair are properly installed
and connected.
5. With the DRBIIIt, clear DTCs and Reset Memory all engine values.
6. Run the engine for one warm-up cycle to verify proper operation.
7. Road test the vehicle. Use all accessories that may be related to this repair.
8. With the DRBIIIt, confirm that no DTC’s or Secondary Indicators are present and that all
components are functioning properly.
9. If this test is being performed after a No Trouble Code test, verify the symptom is no longer
present.
Are any DTCs or symptoms remaining?

Yes → Check for any related Technical Service Bulletins and/or refer to the
appropriate Symptom list (Diagnostic Procedure).
No → Repair is complete.

447
bY dR.dEaDhEaD
VERIFICATION TESTS

Verification Tests — Continued

POWERTRAIN VERIFICATION TEST VER - 3 APPLICABILITY

1. NOTE: After completing the Powertrain Verification Test the Transmission Verifi- All
cation Test must be performed.
2. NOTE: If the PCM has been replaced and the correct VIN and mileage have not
been programmed, a DTC will set in the ABS Module, Airbag Module and the SKIM.
3. NOTE: If the vehicle is equipped with a Sentry Key Immobilizer System, Secret Key
data must be updated. Refer to the Service Information for the PCM, SKIM and the
Transponder (ignition key) for programming information.
4. Inspect the vehicle to ensure that all components related to the repair are properly installed
and connected.
5. With the DRBIIIt, clear DTCs.
6. Perform generator output test. Refer to the appropriate service information as necessary.
7. Start the engine and set engine speed to 2000 RPM for at least thirty seconds.
8. Cycle the ignition key off and on.
9. With the DRBIIIt, read the DTCs.
Are any DTCs or symptoms remaining?
Yes → Check for any Technical Service Bulletins and/or refer to the appropriate
Symptom list (Diagnostic Procedure).

No → Repair is complete.

448
bY dR.dEaDhEaD
 VERIFICATION TESTS

Verification Tests — Continued

POWERTRAIN VERIFICATION TEST VER - 4 APPLICABILITY

1. NOTE: After completing the Powertrain Verification Test the Transmission Verifi- All
cation Test must be performed.
2. NOTE: If the PCM has been replaced and the correct VIN and mileage have not
been programmed, a DTC will set in the ABS Module, Airbag Module and the SKIM.
3. NOTE: If the vehicle is equipped with a Sentry Key Immobilizer System, Secret Key
data must be updated. Refer to the Service Information for the PCM, SKIM and the
Transponder (ignition key) for programming information.
4. Inspect the vehicle to ensure that all engine components are properly installed and
connected.
5. Connect the DRBIIIt to the data link connector and erase all codes.
6. Turn the speed control ON (if equipped, cruise light will be on).
7. Depress and release the SET Switch when the vehicle speed is greater than 35 MPH. The
speed control should engage and hold the selected speed.
8. Press and hold the RESUME/ACCEL Switch. The vehicle speed should increase by at least
2 MPH.
9. Press and hold the COAST switch. The vehicle speed should decrease.
10. Using caution, press and release the brake pedal. The speed control should disengage.
11. Bring the vehicle speed back up to 35 MPH.
12. Press the RESUME/ACCEL switch. The speed control should resume the previously set
speed.
13. Hold down the SET switch. The vehicle should decelerate.
14. Ensure vehicle speed is greater than 35 mph and release the SET Switch. The vehicle
should adjust and set a new vehicle speed.
15. Press and release the CANCEL switch. The speed control should disengage.
16. Bring the vehicle speed back up above 35 mph and engage speed control.
17. Turn the Speed Control Off. (Cruise light will be off). The speed control should disengage.
18. NOTE: OVERSHOOT/UNDERSHOOT FOLLOWING SPEED CONTROL SET.
19. If the vehicle operator repeatedly presses and releases the SET button with their foot off of
the accelerator (referred to as 9lift foot set9), the vehicle may accelerate and exceed the desired
set speed by up to 5 mph (8 km/h).
20. It may also decelerate to less than the desired set speed, before finally achieving the desired
set speed.
21. The Speed Control System has an adaptive strategy that compensates for vehicle-to-vehicle
variations in speed control cable lengths.
22. When the speed control is set with the vehicles operators foot off of the accelerator pedal,
the speed control thinks there is excessive speed control cable slack and adapts accordingly.
23. If the 9lift foot sets9 are continually used, a speed control overshoot/undershoot condition
will develop.
24. To 9unlearn9 the overshoot/undershoot condition, the vehicle operator has to press and
release the set button while maintaining the desired set speed using the accelerator pedal (not
decelerating or accelerating).
25. Then turn the cruise control switch to the OFF position (or press the CANCEL button if
equipped) after waiting 10 seconds.
26. This procedure must be performed approximately 10-15 times to completely unlearn the
overshoot/undershoot condition.
Did the Speed Control pass the above test?

Yes → Repair is complete.

No → Check for any related Technical Service Bulletins and/or refer to the
appropriate Symptom list (Diagnostic Procedure).

449
bY dR.dEaDhEaD
VERIFICATION TESTS

Verification Tests — Continued

POWERTRAIN VERIFICATION TEST VER - 5 APPLICABILITY

1. NOTE: After completing the Powertrain Verification Test the Transmission Verifi- All
cation Test must be performed.
2. NOTE: If the PCM has been replaced and the correct VIN and mileage have not
been programmed, a DTC will set in the ABS Module, Airbag Module and the SKIM.
3. NOTE: If the vehicle is equipped with a Sentry Key Immobilizer System, Secret Key
data must be updated. Refer to the Service Information for the PCM, SKIM and the
Transponder (ignition key) for programming information.
4. NOTE: When replacing an O2 Sensor, the PCM RAM memory must be cleared,
either by disconnecting the PCM C-1 connector or momentarily disconnecting the
Battery negative terminal.
5. The NGC learns the characteristics of each O2 heater element and these old values should
be cleared when installing a new O2 sensor. The customer may experience driveability issues
if this is not performed.
6. Inspect the vehicle to ensure that all engine components are properly installed and
connected. Reassemble and reconnect components as necessary.
7. Connect the DRBIIIt to the data link connector.
8. Ensure the fuel tank has at least a quarter tank of fuel. Turn off all accessories.
9. If the Catalyst was replaced, with the DRBIIIt go to the Miscellaneous Menu Option
9Catalyst Replaced9 and press enter.
10. If a Comprehensive Component DTC was repaired, perform steps 9 - 12. If a Major OBDII
Monitor DTC was repaired skip those steps and continue verification.
11. After the ignition has been off for at least 10 seconds, restart the vehicle and run 2 minutes.
12. With the DRBIIIt, monitor the appropriate pre-test enabling conditions until all conditions
have been met. Once the conditions have been met, switch screen to the appropriate OBDII
monitor, (Audible beeps when the monitor is running).
13. If the repaired OBDII trouble code has reset or was seen in the monitor while on the road
test, the repair is not complete. Check for any related technical service bulletins or flash
updates and return to Symptom List.
14. If the conditions cannot be duplicated, erase all DTCs with the DRBIIIt.
15. If another DTC has set, return to the Symptom List and follow the path specified for that
DTC.
Did the OBDII Monitor run successfully and has the Good Trip Counter changed to one or
more?

Yes → Repair is complete.

No → Check for any related Technical Service Bulletins and/or refer to the
appropriate Symptom list (Diagnostic Procedure).

450
bY dR.dEaDhEaD
 VERIFICATION TESTS

Verification Tests — Continued

POWERTRAIN VERIFICATION TEST VER - 6 APPLICABILITY

1. Install the Miller Tool #8404 Evaporative Emission Leak Detector (EELD). according to the All
instructions in the previous DTC table.
2. Set the smoke/air control switch to AIR.
3. Insert the tester’s AIR supply tip (clear hose) into the appropriate calibration orifice on the
tester’s control panel (based on DTC leak size).
4. Press the remote smoke/air start button.
5. Position the red flag on the air flow meter so it is aligned with the indicator ball.
6. When the calibration is complete, release the remote button. The EELD is now calibrated the
flow meter in liters per minute to the size leak indicated by the DTC set in the PCM.
7. Connect the Air supply hose from the EELD to the vehicle.
8. Press the remote button to activate AIR flow.
9. NOTE: Larger volume fuel tanks, lower fuel levels or if the vehicle is equipped with
a Flow Management Valve may indicate high flow and will require 4 to 5 minutes to
fill.
10. Compare the flow meter indicator ball reading to the red flag.
11. ABOVE the red flag indicates a leak present.
12. BELOW the red flag indicates a sealed system.
13. If the indicator ball shows a leak present, perform the smoke test indicated in the previous
test and identify the leak and repair. Perform this verification test when the repair is complete.
Did the indicator ball indicate the a leak is present??

Yes → Repeat the DTC test to identify the leak and repair.
No → Repair is complete.

SKIS VERIFICATION APPLICABILITY

1. Reconnect all previously disconnected components and connectors. All
2. Obtain the vehicle’s unique Personal Identification Number (PIN) assigned to it’s original
SKIM. This number can be obtained from the vehicle’s invoice or Chrysler’s Customer Center
(1-800-992-1997).
3. NOTE: When entering the PIN, care should be taken because the SKIM will only
allow 3 consecutive attempts to enter the correct PIN. If 3 consecutive incorrect PINs
are entered, the SKIM will Lock Out the DRB for 1 hour.
4. To exit Lock Out mode, the ignition key must remain in the Run position continually for 1
hour. Turn off all accessories and connect a battery charger if necessary.
5. With the DRB, select Theft Alarm, SKIM and Miscellaneous. Then, select the desired
procedure and follow the steps that will be displayed.
6. If the SKIM has been replaced, ensure all of the vehicle ignition keys are programmed to the
new SKIM.
7. NOTE: Prior to returning vehicle to the customer, perform a module scan to be sure
that all DTCs are erased. Erase any DTCs that are found.
8. With the DRB, erase all DTCs. Perform 5 ignition key cycles leaving the key on for at least
90 seconds per cycle.
9. With the DRB, read the SKIM DTCs.
Are there any SKIM DTCs?

Yes → Repair is not complete, refer to appropriate symptom.

No → Repair is complete.

451
bY dR.dEaDhEaD
VERIFICATION TESTS

Verification Tests — Continued

TRANSMISSION NO TROUBLE CODE VERIFICATION TEST APPLICABILITY

1. Inspect the vehicle to ensure that all engine and transmission components are properly All
installed and connected. Assemble and connect components as necessary.
2. Check if the initial symptom still exists, this may require a road test. If the symptom still
exists, return to the symptom list and perform the appropriate symptom. Make sure to check
for any Technical Service Bulletins that may apply.
3. With the DRBIIIt, erase any erroneous DTCs that may have been set due to a test procedure.
Does the symptom still exist?

Yes → Repair is not complete, refer to appropriate symptom.

No → Repair is complete.

452
bY dR.dEaDhEaD
 COMPONENT LOCATIONS
C
8.0 COMPONENT LOCATIONS O
M
8.1 CONTROL MODULES AND PDC P
O
N
E
N
T

L
O
C
A
T
I
O
N
S

8.2 DATA LINK CONNECTOR

453
bY dR.dEaDhEaD
 COMPONENT LOCATIONS
C
O 8.3 SENSORS AND SOLENOIDS
M 4.0L
P
O
N
E
N
T

L
O
C
A
T
I
O
N
S
2.4L 4.0L

2.4L 4.0L

454
bY dR.dEaDhEaD
 COMPONENT LOCATIONS
C
2.4L 2.4L O
M
P
O
N
E
N
T

L
O
C
A
T
I
O
N
4.0L 2.4L S

2.4L
2.4L

455
bY dR.dEaDhEaD
 COMPONENT LOCATIONS
C
O 8.3 SENSORS AND SOLENOIDS (Continued)
M 4.0L
P
O
N
E
N
T

L
O
C
A
T
I
O
N
S

1/1 Federal & BUX 1/2 Federal & BUX

1/1 and 2/1 Calif & EURO III 1/2 and 2/2 Calif. & EURO III

456
bY dR.dEaDhEaD
 COMPONENT LOCATIONS
C
1.2 Calif. & EURO III O
M
P
O
N
E
N
T

L
O
C
A
T
I
O
N
S
8.4 FUEL SYSTEM

457
bY dR.dEaDhEaD
 COMPONENT LOCATIONS
C
O 8.4 FUEL SYSTEM (Continued)
M
P
O
N
E
N
T

L
O
C
A
T
I
O
N
S

8.5 SWITCHES

458
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
9.0 CONNECTOR PINOUTS

A/C COMPRESSOR CLUTCH - BLACK 2 WAY

CAV CIRCUIT FUNCTION
1 C3 18DB/YL (2.4L) A/C CLUTCH RELAY OUTPUT
1 C3 20DB/YL (4.0L) A/C CLUTCH RELAY OUTPUT
2 Z939 18BK (2.4L) GROUND
2 Z987 20BK (4.0L) GROUND

A/C HIGH PRESSURE SWITCH (4.0L) - BLACK 2 WAY

CAV CIRCUIT FUNCTION
1 C221 20LB/OR A/C SELECT SIGNAL
2 C22 20LB/WT A/C SWITCH SIGNAL

C
O
N
N
E
A/C LOW PRESSURE SWITCH - GREEN 2 WAY C
CAV CIRCUIT FUNCTION
T
1 C20 20DB/YL (2.4L) A/C REQUEST SIGNAL
O
1 C20 18DB/YL (4.0L) A/C REQUEST SIGNAL
R
2 C221 20LB/OR (2.4L) A/C SELECT SIGNAL
2 C22 20LB/WT (4.0L) A/C SELECT SIGNAL
P
I
N
O
U
T
A/C PRESSURE TRANSDUCER (2.4L) - 4 WAY S
CAV CIRCUIT FUNCTION
1 K900 20DB/DG SENSOR GROUND
2 F856 20YL/PK 5 VOLT SUPPLY
3 C18 20LB/BR A/C PRESSURE SIGNAL
4 - -

459
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

AMBIENT TEMPERATURE SENSOR (ENGINE) - 2 WAY

CAV CIRCUIT FUNCTION
1 G31 20VT/LG AAT SIGNAL
2 K900 20DB/DG SENSOR GROUND

BATTERY TEMPERATURE SENSOR - BLACK 2 WAY

CAV CIRCUIT FUNCTION
1 K25 20DB/VT BATT TEMP SIGNAL
2 K900 20DB/DG SENSOR GROUND

C
O
N
N BRAKE LAMP SWITCH - GRAY 6 WAY
E CAV CIRCUIT FUNCTION
C 1 B15 20DG/WT BRAKE SWITCH NO. 1 SIGNAL
T 1 B15 20DG/WT BRAKE SWITCH NO. 1 SIGNAL
O 2 Z249 20BK/OR GROUND
R 3 V32 20VT/YL (EXCEPT S/C SUPPLY
POSTAL)
P 4 V30 20VT/WT (EXCEPT S/C BRAKE SWITCH OUTPUT
POSTAL)
I
5 A103 18GY/RD FUSED B(+)
N
6 L50 18WT/TN BRAKE LAMP SWITCH OUTPUT
O
U
T
S

460
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
C102 - (ENGINE SIDE)
CAV CIRCUIT
1 A209 18RD
2 F26 16PK/OR
3 B1 18DG/OR (4.0L EXCEPT
ABS)
3 G301 20VT/LB (4.0L OFF-
ROAD PACKAGE)
4 B2 18DG/LB (4.0L EXCEPT
ABS)
4 A850 18RD/WT (4.0L OFF-
ROAD PACKAGE)
5 C20 20DB/YL (2.4L A/C)
6 B3 18DG/YL (4.0L EXCEPT
ABS)
6 G300 20VT/WT (4.0L OFF-
ROAD PACKAGE)
7 B4 18DG/GY (4.0L EXCEPT
ABS)
7 A750 18TN/RD (4.0L OFF-
ROAD PACKAGE)
8 N4 20DB/WT
9 L1 20WT/LG
10 F102 20PK/DB
11 K334 18BR C
12 T750 14YL/GY O
13 G93 20VT/LB N
14 A109 18OR/RD N
E
C102 - GRAY (HEADLAMP AND DASH SIDE) C
CAV CIRCUIT T
1 A209 18RD/YL O
2 F26 16PK/OR R
3 B1 18DG/OR (ABS)
3 G301 20VT/LB (OFF-ROAD P
PACKAGE) I
4 B2 18DG/LB (ABS) N
4 A850 18RD/WT (OFF-ROAD O
PACKAGE)
U
5 C20 20DB/YL (2.4L A/C)
T
6 B3 18DG/YL (ABS)
S
6 G300 20VT/WT (OFF-ROAD
PACKAGE)
7 B4 18DG/GY (ABS)
7 A750 18TN/RD (OFF-ROAD
PACKAGE)
8 N4 20DB/WT
9 L1 20WT/LG
10 F102 20PK/DB
11 K334 18BR
12 T750 14YL/GY
13 G93 20VT/LB
14 A109 18OR/RD

461
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
C103 - BLACK (ENGINE SIDE)
CAV CIRCUIT
1 D20 18WT/LG
2 G31 18VT/LG
3 C221 20LB/OR (4.0L)
4 F856 20YL/PK (2.4L)
4 K399 18BR/GY (4.0L)
5 K299 18BR/WT
6 D25 18WT/VT
7 D21 18WT/BR
8 K900 20DB/DG
9 F1 18PK/WT
10 Y3 18LG
11 Z11 20BK/LG
12 K75 20DB/OR (DRL)
13 K66 18DB/WT (2.4L)
14 C3 20DB/BK (2.4L A/C)
14 C3 20DB/YL (4.0L A/C)

C103 - BLACK (HEADLAMP AND DASH SIDE)

CAV CIRCUIT

C 1 D20 20WT/LG

O 2 G31 20VT/LG

N 3 C221 20LB/OR (4.0L)

N 4 F856 20YL/PK (2.4L)

E 4 K399 20BR/GY (4.0L)

C 5 K299 20BR/WT

T 6 D25 18WT/VT

O 7 D21 20WT/BR

R 8 K900 20DB/DG
9 F1 20PK/WT

P 10 Y3 18LG

I 10 Y3 20LG

N 11 Z11 20BK/LG

O 12 K75 20DB/OR (DRL)

U 13 K66 20DB/WT (2.4L)

T 14 C3 20DB/YL (A/C)

S
C104 (RHD) - BLACK (ENGINE SIDE)
CAV CIRCUIT
1 A209 18RD
2 F26 16PK/OR
3 A109 18OR/RD
4 K334 18BR
5 -
6 T750 14YL/GY
7 G93 20VT/LB
8 N4 20DB/WT
9 L1 20WT/LG
10 F102 20PK/DB

462
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
C104 (RHD) - BLACK (HEADLAMP AND DASH SIDE)
CAV CIRCUIT
1 A209 18RD
2 F26 16PK/OR
3 A109 18OR/RD
4 K334 18BR
5 -
6 T750 14YL/GY
7 G93 20VT/LB
8 N4 20DB/WT
9 L1 20WT/LG
10 F102 20PK/DB

C181 (2.4L) - BLACK (ENGINE INTAKE SIDE)

CAV CIRCUIT
1 K334 18OR/DG
2 C3 18DB/YL
3 Z987 18BK/GR
4 K11 18WT/DB
5 K12 18TN
6 K13 18YL/WT
7 K14 18LB/BR C
8 K44 18TN/YL O
9 K900 18BK/LB N
10 - N
E
C181 (2.4L) - BLACK (ENGINE SIDE) C
CAV CIRCUIT T
1 K334 18BR O
2 C3 20DB/BK R
3 Z987 20BK
4 K11 18BR/YL P
5 K12 18BR/DB I
6 K13 18BR/LB N
7 K14 18BR/TN O
8 K44 18DB/GY U
9 K900 18DB/DG T
10 - S

C182 (2.4L) - BLACK (ENGINE INTAKE SIDE)

CAV CIRCUIT
1 -
2 -
3 K61 18YL/BK
4 K961 18GY/RD
5 K21 18BK/RD
6 K2 18TN/BK
7 K1 18DG/RD
8 K22 18OR/DB
9 F856 18YL/PK
10 G6 18GY/YL
11 -
12 F855 18OR
13 -
14 -

463
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
C182 (2.4L) - BLACK (ENGINE SIDE)
CAV CIRCUIT
1 -
2 -
3 K61 18VT/GY
4 K961 18BR/VT
5 K21 18DB/LG
6 K2 18VT/OR
7 K1 18VT/BR
8 K22 18BR/OR
9 F856 18YL/PK
10 G6 18VT/GY
11 -
12 F855 18PK/YL
13 -
14 -

CAMSHAFT POSITION SENSOR - BLACK 3 WAY

CAV CIRCUIT FUNCTION
C 1 F856 20YL/PK 5 VOLT SUPPLY
O 2 K900 20DB/DG SENSOR GROUND
N 3 K44 20DB/GY (2.4L) CMP SIGNAL
N 3 K44 18DB/GY (4.0L) CMP SIGNAL
E
C
T
O
R CLOCKSPRING C1 - 4 WAY
CAV CIRCUIT FUNCTION
P 1 X3 20RD/YL HORN RELAY CONTROL
I 2 V37 20VT S/C SWITCH NO. 1 SIGNAL
N 3 K900 20DB/DG SENSOR GROUND
O 4 - -
U
T
S

CLUTCH PEDAL POSITION SWITCH (M/T) - BLACK 2 WAY

CAV CIRCUIT FUNCTION
1 T141 18YL/OR CLUTCH INTERLOCK SWITCH SENSE
2 Z902 18BK GROUND

464
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

COIL CAPACITOR - 2 WAY

CAV CIRCUIT FUNCTION
1 K334 18BR ASD RELAY OUTPUT
2 - -

CRANKSHAFT POSITION SENSOR - BLACK 3 WAY

CAV CIRCUIT FUNCTION
1 F855 20PK/YL 5 VOLT SUPPLY
2 K900 20DB/DG SENSOR GROUND
3 K24 18BR/LB CKP SIGNAL
C
O
N
N
E
C
T
ENGINE COOLANT TEMPERATURE SENSOR - BLACK 2 WAY O
CAV CIRCUIT FUNCTION R
1 K900 20DB/DG (2.4L) SENSOR GROUND
1 K2 18VT/OR (4.0L) ECT SIGNAL P
2 K2 20VT/OR (2.4L) ECT SIGNAL I
2 K900 20DB/DG (4.0L) SENSOR GROUND N
O
U
T
S

ENGINE OIL PRESSURE SWITCH - BLACK 2 WAY

CAV CIRCUIT FUNCTION
1 G6 20VT/GY OIL PRESSURE SIGNAL
2 - -

465
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

EVAP/PURGE SOLENOID - 2 WAY

CAV CIRCUIT FUNCTION
1 K70 20DB/BR EVAP/PURGE SOL SIGNAL
2 K52 20DB/WT EVAP/PURGE SOL CONTROL

FUEL INJECTOR NO. 1 (2.4L) - 2 WAY

CAV CIRCUIT FUNCTION
1 F142 16PK/GY ASD RELAY OUTPUT
2 K11 16BR/YL INJECTOR CONTROL NO. 1

C
O
N FUEL INJECTOR NO. 1 (4.0L) - 2 WAY
N CAV CIRCUIT FUNCTION
E 1 K334 18BR ASD RELAY OUTPUT
C 2 K11 18BR/YL INJECTOR CONTROL NO. 1
T
O
R

P
I
N
O FUEL INJECTOR NO. 2 (2.4L) - 2 WAY
U CAV CIRCUIT FUNCTION

T 1 F142 16PK/GY ASD RELAY OUTPUT

S 2 K12 16BR/DB INJECTOR CONTROL NO. 2

FUEL INJECTOR NO. 2 (4.0L) - 2 WAY

CAV CIRCUIT FUNCTION
1 K334 18BR ASD RELAY OUTPUT
2 K12 18BR/DB INJECTOR CONTROL NO. 2

466
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

FUEL INJECTOR NO. 3 (2.4L) - 2 WAY

CAV CIRCUIT FUNCTION
1 F142 16PK/GY ASD RELAY OUTPUT
2 K13 16BR/LB INJECTOR CONTROL NO. 3

FUEL INJECTOR NO. 3 (4.0L) - 2 WAY

CAV CIRCUIT FUNCTION
1 K334 18BR ASD RELAY OUTPUT
2 K13 18BR/LB INJECTOR CONTROL NO. 3

C
O
N
FUEL INJECTOR NO. 4 (2.4L) - 2 WAY N
CAV CIRCUIT FUNCTION
E
1 F142 16PK/GY ASD RELAY OUTPUT
C
2 K14 16BR/TN INJECTOR CONTROL NO. 4
T
O
R

P
I
N
O
FUEL INJECTOR NO. 4 (4.0L) - 2 WAY U
CAV CIRCUIT FUNCTION
T
1 K334 18BR ASD RELAY OUTPUT
S
2 K14 18BR/TN INJECTOR CONTROL NO. 4

FUEL INJECTOR NO. 5 (4.0L) - 2 WAY

CAV CIRCUIT FUNCTION
1 K334 18BR ASD RELAY OUTPUT
2 K38 18BR/OR INJECTOR CONTROL NO. 5

467
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

FUEL INJECTOR NO. 6 (4.0L) - 2 WAY

CAV CIRCUIT FUNCTION
1 K334 18BR ASD RELAY OUTPUT
2 K58 18BR/VT INJECTOR CONTROL NO. 6

FUEL PUMP MODULE - 4 WAY

CAV CIRCUIT FUNCTION
1 Z987 18BK GROUND
2 N4 20DB/WT FUEL LEVEL SENSOR SIGNAL
3 K900 20DB/DG SENSOR GROUND
4 A109 18OR/RD FUEL PUMP RELAY OUTPUT

C
O
N
N
E
C
T
O
GENERATOR - 3 WAY
R
CAV CIRCUIT FUNCTION
1 - FIELD WIRES
P
2 - FIELD WIRE CONNECTOR
I
3 - B(+) (OUTPUT TERMINAL)
N
O
U
T
S

GENERATOR - BLACK 2 WAY

CAV CIRCUIT FUNCTION
1 K125 18BR/DG GEN FIELD CONTROL
2 Z20 18BR/BK GROUND

468
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

IDLE AIR CONTROL MOTOR - 2 WAY

CAV CIRCUIT FUNCTION
1 K961 20BR/VT (2.4L) IAC SIGNAL
1 K961 18BR/VT (4.0L) IAC SIGNAL
2 K61 20VT/GY (2.4L) IAC CONTROL
2 K61 18VT/GY (4.0L) IAC CONTROL

IGNITION COIL PACK (2.4L) - BLACK 3 WAY

CAV CIRCUIT FUNCTION
1 K17 18DB/TN COIL CONTROL NO. 2
2 K334 18BR ASD RELAY OUTPUT
3 K19 18DB/DG COIL CONTROL NO. 1

C
O
N
N
E
C
T
IGNITION COIL PACK (4.0L) - BLACK 4 WAY O
CAV CIRCUIT FUNCTION R
1 K19 18DB/DG COIL CONTROL NO. 1
2 K334 18BR ASD RELAY OUTPUT P
3 K17 18DB/TN COIL CONTROL NO. 2 I
4 K18 18DB/OR COIL CONTROL NO. 3 N
O
U
T
S

INPUT SPEED SENSOR - 2 WAY

CAV CIRCUIT FUNCTION
1 T52 18DG/OR INPUT SPEED SENSOR SIGNAL
2 T13 18DG/VT SPEED SENSOR GROUND

469
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

INTAKE AIR TEMPERATURE SENSOR (2.4L) - 2 WAY

CAV CIRCUIT FUNCTION
1 K900 20DB/DG SENSOR GROUND
2 K21 20BR/WT IAT SIGNAL

INTAKE AIR TEMPERATURE SENSOR (4.0L) - GRAY 2 WAY

CAV CIRCUIT FUNCTION
1 K900 20DB/DG SENSOR GROUND
2 K21 18BK/RD IAT SIGNAL

C
O
N
N
E
C
T
O
R
MANIFOLD ABSOLUTE PRESSURE SENSOR - 3 WAY
CAV CIRCUIT FUNCTION
P 1 K1 20VT/BR (2.4L) MAP SIGNAL
I 1 K1 18VT/BR (4.0L) MAP SIGNAL
N 2 K900 20DB/DG SENSOR GROUND
O 3 F856 20YL/PK 5 VOLT SUPPLY
U
T
S

NATURAL VACUUM LEAK DETECTION ASSEMBLY - BLACK 3 WAY

CAV CIRCUIT FUNCTION
1 Z913 20BK GROUND
2 K107 20VT/WT NVLD SWITCH SIGNAL
3 K106 20VT/LB NVLD SOL CONTROL

470
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

OUTPUT SPEED SENSOR (A/T) - 2 WAY

CAV CIRCUIT FUNCTION
1 T14 18DG/BR OUTPUT SPEED SENSOR SIGNAL
2 T13 18DG/VT SPEED SENSOR GROUND

OXYGEN SENSOR 1/1 UPSTREAM (2.4L) - 4 WAY

CAV CIRCUIT FUNCTION
1 K99 18BR/LG O2 1/1 HEATER CONTROL
2 Z42 18BK/LG GROUND
3 K902 18BR/DG O2 RETURN (UPSTREAM)
4 K41 18DB/LB O2 1/1 SIGNAL

C
O
N
N
E
OXYGEN SENSOR 1/1 UPSTREAM (4.0L) - 4 WAY C
CAV CIRCUIT FUNCTION
T
1 K99 18BR/LG O2 1/1 HEATER CONTROL
O
2 Z42 18BK/LG GROUND
R
3 K902 18BR/DG O2 RETURN (UPSTREAM)
4 K41 18DB/LB O2 1/1 SIGNAL
P
I
N
O
U
T
S

OXYGEN SENSOR 1/2 DOWNSTREAM - BLACK 4 WAY

CAV CIRCUIT FUNCTION
1 K299 18BR/WT O2 1/2 HEATER CONTROL
2 Z43 18BK/LB GROUND
3 K904 18DB/DG O2 RETURN (DOWNSTREAM)
4 K141 18DB/YL O2 1/2 SIGNAL

471
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

OXYGEN SENSOR 2/1 UPSTREAM (4.0L) - 4 WAY

CAV CIRCUIT FUNCTION
1 K199 18BR/VT O2 2/1 HEATER CONTROL
2 Z42 18BK/LG GROUND
3 K902 18BR/DG O2 RETURN (UPSTREAM)
4 K43 18DB/LG O2 2/1 SIGNAL

OXYGEN SENSOR 2/2 DOWNSTREAM (4.0L) - 4 WAY

CAV CIRCUIT FUNCTION
1 K399 18BR/GY O2 2/2 HEATER CONTROL
2 Z43 18BK/LB GROUND
C 3 K904 18BD/DG O2 RETURN (DOWNSTREAM)
O 4 K243 18BR O2 2/2 SIGNAL
N
N
E
C
T
O
R

P
I
N
O
U
T
S

472
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

C
O
N
N
E
C
T
O
R

P
I
N
O
U
T
S

473
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
FUSES (PDC)
FUSE AMPS FUSED CIRCUIT FUNCTION
NO.
1 40A A502 12RD/LG FUSED B(+)
2 40A A902 12RD FUSED B(+)
3 40A A906 12RD FUSED B(+)
4 40A A16 12GY (2.4L) FUSED B(+)
5 20A A30 16RD/WT (A/T) FUSED B(+)
6 40A A8 14RD FUSED B(+)
7 - - -
8 40A A107 12TN/RD (ABS) FUSED B(+)
9 20A A209 18RD/YL FUSED B(+)
9 20A A209 18RD (42RLE) FUSED B(+)
9 20A A209 18RD/YL (NA1) FUSED B(+)
10 40A A940 12RD FUSED B(+)
11 - - -
12 30A A111 12DG/RD (ABS) FUSED B(+)
13 40A A991 12RD FUSED B(+)
14 - - -
15 50A INTERNAL FUSED B(+)
16 - - -
17 20A A205 18RD/OR FUSED B(+)
C 18 20A A43 18RD/DG FUSED B(+)
O 18 20A A43 18RD/DG FUSED B(+)
N 19 20A A39 18RD/DG (OPTION 1) FUSED B(+)
N 19 20A A39 16RD/DG (OPTION 2) FUSED B(+)
E 20 15A F306 16DB/PK FUSED B(+)
C 21 10A A926 20RD FUSED B(+)
T 22 25A A1 16RD FUSED B(+)
O 23 20A A930 18RD FUSED B(+)
R 24 20A INTERNAL (OFF-ROAD PACKAGE) FUSED B(+)
25 - - -
P 26 10A M21 20YL/BR FUSED B(+)
I 27 20A A701 18BR/RD FUSED B(+)
N 28 10A Y3 18LG FUSED SENSOR GROUND
O 28 10A K900 20DB/DG SENSOR GROUND
U 28 10A Y3 20LG FUSED SENSOR GROUND
T
S
A/C COMPRESSOR CLUTCH RELAY (IN PDC)
CAV CIRCUIT FUNCTION
A6 F960 20PK/LG FUSED IGNITION SWITCH OUTPUT (RUN-START)
A6 F960 20PK/LG (2.4L) FUSED IGNITION SWITCH OUTPUT (RUN-START)
A7 - -
A8 C13 20LB/OR A/C CLUTCH RELAY CONTROL
A9 C3 20DB/YL A/C CLUTCH RELAY OUTPUT
A10 A926 20RD FUSED B(+)

AUTOMATIC SHUT DOWN RELAY (IN PDC)

CAV CIRCUIT FUNCTION
A11 K342 20BR/WT ASD RELAY CONTROL
A12 - -
A13 F1 20PK/WT FUSED IGNITION SWITCH OUTPUT (RUN-START)
A13 F1 20PK/WT FUSED IGNITION SWITCH OUTPUT (RUN-START)
A14 K334 18BR ASD RELAY OUTPUT
A15 A209 18RD/YL FUSED B(+)

474
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
ENGINE STARTER MOTOR RELAY (IN PDC)
CAV CIRCUIT FUNCTION
B1 A8 14RD FUSED B(+)
B2 T750 14YL/GY ENGINE STARTER MOTOR RELAY OUTPUT
B3 T752 20DG/OR STARTER MOTOR RELAY CONTROL
B4 - -
B5 F26 16PK/OR IGNITION SWITCH OUTPUT (START)

FUEL PUMP RELAY (IN PDC)

CAV CIRCUIT FUNCTION
C6 F1 20PK/WT FUSED IGNITION SWITCH OUTPUT (RUN-START)
C6 F1 20PK/WT FUSED IGNITION SWITCH OUTPUT (RUN-START)
C7 - -
C8 K31 20BR FUEL PUMP RELAY CONTROL
C9 A109 18OR/RD FUEL PUMP RELAY OUTPUT
C10 A930 18RD FUSED B(+)

HIGH SPEED RADIATOR FAN RELAY (2.4L)

CAV CIRCUIT FUNCTION
D10 A16 12GY FUSED B(+)
D11 N112 20DB/OR HIGH SPEED RADIATOR FAN RELAY CONTROL
D13 F960 20PK/LG FUSED IGNITION SWITCH OUTPUT (RUN-START) C
D14 C25 12YL HIGH SPEED RADIATOR RELAY OUTPUT O
N
LOW SPEED RADIATOR FAN RELAY (2.4L) N
CAV CIRCUIT FUNCTION E
D2 A16 12GY FUSED B(+) C
D4 F960 20PK/LG FUSED IGNITION SWITCH OUTPUT (RUN-START) T
D4 F960 20PK/LG FUSED IGNITION SWITCH OUTPUT (RUN-START) O
D6 N201 20DB/LG LOW SPEED RADIATOR FAN RELAY CONTROL R
D8 C23 12DG LOW SPEED FAN RELAY OUTPUT
P
TRANSMISSION CONTROL RELAY (IN PDC) I
CAV CIRCUIT FUNCTION N
A1 A30 16RD/WT FUSED B(+) O
A2 T515 20YL/DB TRANSMISSION CONTROL RELAY CONTROL U
A3 T16 18YL/OR TRANSMISSION CONTROL RELAY OUTPUT T
A4 Z901 18BK GROUND S
A5 - -

475
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

POWER STEERING PRESSURE SWITCH (2.4L) - BLACK 2 WAY

CAV CIRCUIT FUNCTION
1 K66 18DB/WT P/S PRESSURE SWITCH SIGNAL
2 Z987 20BK GROUND

POWERTRAIN CONTROL MODULE C1 - BLACK/BLACK 38 WAY

CAV CIRCUIT FUNCTION
1 - -
2 - -
3 - -
4 - -
5 - -
6 - -
C 7 - -
O 8 - -
N 9 Z130 18BK/BR GROUND
N 10 C20 20DB/YL (2.4L) A/C REQUEST SIGNAL
E 10 C20 18DB/YL (4.0L) A/C REQUEST SIGNAL
C 11 F1 18PK/WT FUSED IGNITION SWITCH OUTPUT (RUN-START)
T 12 F1 18PK/WT (A/T) FUSED IGNITION SWITCH OUTPUT (RUN-START)
O 13 K75 18DB/OR VEHICLE SPEED SENSOR SIGNAL
R 14 - -
15 - -
P 16 - -
I 17 - -
N 18 Z131 18BK/DG GROUND
O 19 - -
U 20 G6 18VT/GY OIL PRESSURE SIGNAL
T 21 - -
S 22 G31 18VT/LG AAT SIGNAL
23 - -
24 - -
25 D20 18WT/LG SCI RECEIVE (PCM)
26 D16 18WT/OR SCI RECEIVE (TCM)
27 F856 18YL/PK 5 VOLT SUPPLY
28 T56 18DG/LB OVERDRIVE OFF SWITCH INDICATOR
29 A209 18RD FUSED B(+)
30 F26 16PK/OR IGNITION SWITCH OUTPUT (START)
31 K141 18DB/YL O2 1/2 SIGNAL
32 K902 18BR/DG O2 RETURN (UPSTREAM)
33 K243 18BR (4.0L) O2 2/2 SIGNAL
34 - -
35 - -
36 D21 18WT/BR SCI TRANSMIT (PCM/CAB)
37 D15 18WT/DG SCI RECEIVE (TCM)
38 D25 18WT/VT PCI BUS

476
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
POWERTRAIN CONTROL MODULE C2 - BLACK/ORANGE 38 WAY
CAV CIRCUIT FUNCTION
1 - -
2 - -
3 - -
4 K58 18BR/VT (4.0L) INJECTOR CONTROL NO. 6
5 K38 18BR/OR (4.0L) INJECTOR CONTROL NO. 5
6 - -
7 K18 18DB/OR (4.0L) COIL CONTROL NO. 3
8 - -
9 K17 18DB/TN COIL CONTROL NO. 2
10 K19 18DB/DG COIL CONTROL NO. 1
11 K14 18BR/TN INJECTOR CONTROL NO. 4
12 K13 18BR/LB INJECTOR CONTROL NO. 3
13 K12 18BR/DB INJECTOR CONTROL NO. 2
14 K11 18BR/YL INJECTOR CONTROL NO. 1
15 - -
16 - -
17 K199 18BR/VT O2 2/1 HEATER CONTROL
18 K99 18BR/LG O2 1/1 HEATER CONTROL
19 K125 18BR/DG GEN FIELD CONTROL
20 K2 18VT/OR ECT SIGNAL
C
21 K22 18BR/OR TP NO. 1 SIGNAL
O
22 - -
N
23 K1 18VT/BR MAP SIGNAL
N
24 - -
E
25 - -
C
26 Y3 18LG (EXCEPT OFF- FUSED SENSOR GROUND
ROAD PACKAGE)
T
26 K77 18BR/WT (OFF-ROAD TRANSFER CASE POSITION SENSOR INPUT
O
PACKAGE) R
27 K900 18DB/DG SENSOR GROUND
28 K961 18BR/VT IAC SIGNAL P
29 F855 18PK/YL 5 VOLT SUPPLY I
30 K21 18DB/LG (2.4L) IAT SIGNAL N
30 K21 18BK/RD (4.0L) IAT SIGNAL O
31 K41 18DB/LB O2 1/1 SIGNAL U
32 K904 18DB/DG O2 RETURN (DOWNSTREAM) T
33 K43 18DB/LG (4.0L) O2 2/1 SIGNAL S
34 K44 18DB/GY CMP SIGNAL
35 K24 18BR/LB CKP SIGNAL
36 - -
37 - -
38 K61 18VT/GY IAC CONTROL

477
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
POWERTRAIN CONTROL MODULE C3 - BLACK/NATURAL 38 WAY
CAV CIRCUIT FUNCTION
1 - -
2 - -
3 K342 20BR/WT ASD RELAY CONTROL
4 N112 20DB/OR RADIATOR FAN RELAY CONTROL
5 V35 20VT/LG (SPEED S/C VENT SOL CONTROL
CONTROL)
6 N201 20DB/LG LOW SPEED RADIATOR FAN RELAY CONTROL
7 V32 20VT/YL S/C SUPPLY
8 K106 20VT/LB NVLD SOL CONTROL
9 K299 20BR/WT O2 1/2 HEATER CONTROL
10 K399 20BR/GY (4.0L) O2 2/2 HEATER CONTROL
11 C13 20LB/OR A/C CLUTCH RELAY CONTROL
12 V36 20VT/YL S/C VACUUM SOL CONTROL
13 - -
14 - -
15 - -
16 - -
17 - -
18 - -
19 K334 18BR ASD RELAY OUTPUT
C 20 K52 20DB/WT EVAP/PURGE SOL CONTROL
O 21 T141 18YL/OR CLUTCH INTERLOCK SWITCH SENSE
N 22 - -
N 23 B15 20DG/WT BRAKE SWITCH NO. 1 SIGNAL
E 24 C221 20LB/OR A/C SELECT SIGNAL
C 25 - -
T 26 - -
O 27 - -
R 28 K334 18BR ASD RELAY OUTPUT
29 K70 20DB/BR EVAP/PURGE SOL SIGNAL
P 30 K66 20DB/WT P/S PRESSURE SWITCH SIGNAL
I 31 C18 20LB/BR A/C PRESSURE SIGNAL
N 32 K25 20DB/VT BATT TEMP SIGNAL
O 33 N4 20DB/WT FUEL LEVEL SENSOR SIGNAL
U 34 V37 20VT S/C SWITCH NO. 1 SIGNAL
T 35 K107 20VT/WT NVLD SWITCH SIGNAL
S 36 - -
37 K31 20BR FUEL PUMP RELAY CONTROL
38 T752 20DG/OR STARTER MOTOR RELAY CONTROL

478
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
POWERTRAIN CONTROL MODULE C4 - BLACK/GREEN 38 WAY
CAV CIRCUIT FUNCTION
1 T60 16YL/GY OD SOLENOID CONTROL
2 T59 16YL/LB UD SOLENOID CONTROL
3 - -
4 - -
5 - -
6 T19 16YL/DB 2-4 SOLENOID CONTROL
7 - -
8 - -
9 - -
10 T20 16DG/WT L/R SOLENOID CONTROL
11 T140 18YL/GY MS SOLENOID CONTROL
12 Z903 16BK GROUND
13 Z903 16BK GROUND
14 - -
15 T1 18DG/LB TRS T1 SENSE
16 T3 18DG/DB TRS T3 SENSE
17 T6 18DG TOW/HAUL OVERDRIVE OFF SWITCH SENSE
18 T515 18YL/DB TRANSMISSION CONTROL RELAY CONTROL
19 T16 16YL/OR TRANSMISSION CONTROL RELAY OUTPUT
20 - -
C
21 - -
O
22 T9 18DG/TN OD PRESSURE SWITCH SENSE
N
23 - -
N
24 - -
E
25 - -
C
26 - -
T
27 T41 18YL/DB TRS T41 SENSE (P/N)
O
28 T16 16YL/OR TRANSMISSION CONTROL RELAY OUTPUT
R
29 T50 18YL/TN L/R PRESSURE SWITCH SENSE
30 T47 18YL/DG 2-4 PRESSURE SWITCH SENSE
P
31 T38 18YL/BR LINE PRESSURE SENSOR SIGNAL
I
32 T14 18DG/BR OUTPUT SPEED SENSOR SIGNAL
N
33 T52 18DG/OR INPUT SPEED SENSOR SIGNAL
O
34 T13 18DG/VT SPEED SENSOR GROUND
U
35 T54 18DG/OR TRANSMISSION TEMPERATURE SENSOR SIGNAL
T
36 - -
S
37 T42 18DG/YL TRS T42 SENSE
38 - -

RADIATOR FAN MOTOR (2.4L) - 3 WAY

CAV CIRCUIT FUNCTION
1 C25 12DG HIGH SPEED RADIATOR RELAY OUTPUT
2 Z213 12BK GROUND
3 C23 12DB LOW SPEED FAN RELAY OUTPUT

479
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

RADIATOR FAN MOTOR CIRCUIT BREAKER (2.4L) - 2 WAY

CAV CIRCUIT FUNCTION
A Z213 12BK GROUND
B Z823 12BK/DG GROUND

SENTRY KEY IMMOBILIZER MODULE - BLACK 6 WAY

CAV CIRCUIT FUNCTION
1 - -
2 D25 20WT/VT PCI BUS
3 - -
4 F1 20PK/WT FUSED IGNITION SWITCH OUTPUT (RUN-START)
5 Z120 20BK/WT GROUND
6 L177 20WT/OR FUSED B(+)
C
O
N
N
E
C
T SPEED CONTROL SERVO - BLACK 4 WAY
O CAV CIRCUIT FUNCTION

R 1 V36 20VT/YL S/C VACUUM SOL CONTROL

2 V35 20VT/LG S/C VENT SOL CONTROL

P 3 V30 20VT/WT S/C BRAKE SWITCH OUTPUT

I 4 Z901 18BK GROUND

N
O
U
T
S

THROTTLE POSITION SENSOR (2.4L) - 3 WAY

CAV CIRCUIT FUNCTION
1 F855 20PK/YL 5 VOLT SUPPLY
2 K900 20DB/DG SENSOR GROUND
3 K22 20BR/OR TP NO. 1 SIGNAL

480
bY dR.dEaDhEaD
 CONNECTOR PINOUTS

THROTTLE POSITION SENSOR (4.0L) - 3 WAY

CAV CIRCUIT FUNCTION
1 F855 20PK/YL 5 VOLT SUPPLY
2 K900 20DB/DG SENSOR GROUND
3 K22 18BR/OR TP NO. 1 SIGNAL

TOW/HAUL OVERDRIVE OFF SWITCH - 4 WAY

CAV CIRCUIT FUNCTION
1 Z1 20BK GROUND
2 T6 20DG TOW/HAUL OVERDRIVE OFF SWITCH SENSE
3 T56 20DB/LB OVERDRIVE OFF SWITCH INDICATOR
4 E2 20OR/BR PANEL LAMPS FEED C
O
N
N
E
C
T
O
TRANSFER CASE SWITCH (EXCEPT OFF-ROAD PACKAGE) - BLACK 2 WAY
R
CAV CIRCUIT FUNCTION
A G93 20VT/LB 4WD INDICATOR P
B Z987 18BK GROUND I
N
O
U
T
S

TRANSFER CASE SWITCH (OFF-ROAD PACKAGE) - BLACK 2 WAY

CAV CIRCUIT FUNCTION
1 K77 18BR/WT TRANSFER CASE POSITION SENSOR INPUT
2 K900 20DB/DG SENSOR GROUND

481
bY dR.dEaDhEaD
 CONNECTOR PINOUTS
TRANSMISSION RANGE SENSOR - 10 WAY
CAV CIRCUIT FUNCTION
1 F102 20PK/DB FUSED IGNITION SWITCH OUTPUT (RUN)
2 - -
3 T13 18DG/VT SPEED SENSOR GROUND
4 T54 18DG/OR TRANSMISSION TEMPERATURE SENSOR SIGNAL
5 - -
6 L1 20WT/LG BACK-UP LAMP FEED
7 T1 18DG/LB TRS T1 SENSE
8 T3 18DG/DB TRS T3 SENSE
9 T42 18DG/YL TRS T42 SENSE
10 T41 18YL/DB TRS T41 SENSE (P/N)

TRANSMISSION SOLENOID/PRESSURE SWITCH ASSEMBLY - 10 WAY

CAV CIRCUIT FUNCTION
1 T60 16YL/GY OD SOLENOID CONTROL
2 T59 16YL/LB UD SOLENOID CONTROL
3 T16 16YL/OR TRANSMISSION CONTROL RELAY OUTPUT
4 T19 16YL/DB 2-4 SOLENOID CONTROL
5 T47 18YL/DG 2-4 PRESSURE SWITCH SENSE
6 T9 18DG/TN OD PRESSURE SWITCH SENSE

C 7 T20 16DG/WT L/R SOLENOID CONTROL

O 8 - -

N 9 - -

N 10 T50 18YL/TN L/R PRESSURE SWITCH SENSE

E
C
T
O
VEHICLE SPEED SENSOR - BLACK 3 WAY
R CAV CIRCUIT FUNCTION
1 F856 20YL/PK 5 VOLT SUPPLY
P 2 K900 20DB/DG SENSOR GROUND
I 3 K75 18DB/OR VEHICLE SPEED SENSOR SIGNAL
N
O
U
T
S

482
bY dR.dEaDhEaD
 SCHEMATIC DIAGRAMS
10.0 SCHEMATIC DIAGRAMS
10.1 2.4L NGC

S
C
H
E
M
A
T
I
C

D
I
A
G
R
A
M
S
483
bY dR.dEaDhEaD
 SCHEMATIC DIAGRAMS
10.2 4.0L NGC

S
C
H
E
M
A
T
I
C

D
I
A
G
R
A
M
S
484
bY dR.dEaDhEaD
 SCHEMATIC DIAGRAMS
10.3 42 RLE

S
C
H
E
M
A
T
I
C

D
I
A
G
R
A
M
S
485
bY dR.dEaDhEaD
 NOTES

486
bY dR.dEaDhEaD
 CHARTS AND GRAPHS
11.0 CHARTS AND GRAPHS C
H
A
11.1 2.4L ENGINE R
T
S

A
N
D

G
R
A
P
H
S

11.2 4.0L ENGINE

11.3 PRESSURE SWITCH STATES

487
bY dR.dEaDhEaD
 CHARTS AND GRAPHS
C 11.4 SOLENOID APPLICATION CHART
H
A
R
T
S

A
N
D

G
R
A
P
H
S

11.5 SHIFT LEVER ERROR CODES

488
bY dR.dEaDhEaD
 CHARTS AND GRAPHS
11.6 TRANSMISSION TEMPERATURE SENSOR C
H
A
R
T
S

A
N
D

G
R
A
P
H
S

489
bY dR.dEaDhEaD
 CHARTS AND GRAPHS
C
H
A
R
T
S

A
N
D

G
R
A
P
H
S

490
bY dR.dEaDhEaD
 CHARTS AND GRAPHS
C
H
A
R
T
S

A
N
D

G
R
A
P
H
S

491
bY dR.dEaDhEaD
 CHARTS AND GRAPHS
C 2005 TJ Powertrain Publication No. 81-370-05042 December, 2004
H
A
R
T
S

A
N
D

G
R
A
P
H
S

492
bY dR.dEaDhEaD
 DIAGNOSTIC TEST PROCEDURES — TELL US!

DaimlerChrysler Corporation is constantly working to provide the technician the best diagnostic manuals possible.
Your comments and recommendations regarding the diagnostic manuals and procedures are appreciated.

To best understand your suggestion, please complete the form giving us as much detail as possible.

Model Year Body Type Engine

Transmission Vehicle Mileage MDH

Diagnostic Procedure Book No. Page

Comments/recommendations (if necessary, draw sketch)

Name

Submitted by:

Address

City/State/Zip

Business Phone #

All comments become property of DaimlerChrysler Corporation and may be used without compensation.

bY dR.dEaDhEaD
Dealer Technical Operations
800 Chrysler Drive
CIMS 486-02-76
Auburn Hills, MI 48326-2757

bY dR.dEaDhEaD