Product Name: MOBIL ATF 320
Revision Date: 03 Jul 2009
Page 1 of 8
______________________________________________________________________________________________________________________
SAFETY DATA SHEET
SECTION 1 PRODUCT AND COMPANY IDENTIFICATION
As of the revision date above, this (M)SDS meets the regulations in the United Kingdom & Ireland.
PRODUCT
Product Name: MOBIL ATF 320
Product Description: Base Oil and Additives
Product Code: 201530201035, 520411-60
Intended Use: Automatic gearbox fluid
COMPANY IDENTIFICATION
Supplier: EXXONMOBIL LUBRICANTS & SPECIALTIES EUROPE, A DIVISION OF EXXONMOBIL
PETROLEUM & CHEMICAL, BVBA (EMPC)
POLDERDIJKWEG
B-2030 Antwerpen
Belgium
24 Hour Environmental / Health Emergency (UK) 01372 222 000 / (IRELAND) 44 1372 222 000
Telephone
e-mail [email protected]
SECTION 2 HAZARDS IDENTIFICATION
This material is not considered to be hazardous according to regulatory guidelines see Section 15.
HEALTH HAZARDS
Low order of toxicity. Excessive exposure may result in eye, skin, or respiratory irritation. High-pressure
injection under skin may cause serious damage.
Note: This material should not be used for any other purpose than the intended use in Section 1 without expert advice.
Health studies have shown that chemical exposure may cause potential human health risks which may vary from
person to person.
SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS
Reportable Hazardous Substance(s) or Complex Substance(s)
Name CAS# EINECS / Symbols/Risk
ELINCS Concentration Phrases
*
METHACRYLATE COPOLYMER 1 - 5% Xi;R36
* All concentrations are percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume.
Product Name: MOBIL ATF 320
Revision Date: 03 Jul 2009
Page 2 of 8
______________________________________________________________________________________________________________________
SECTION 4 FIRST AID MEASURES
INHALATION
Remove from further exposure. For those providing assistance, avoid exposure to yourself or others. Use
adequate respiratory protection. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek
immediate medical assistance. If breathing has stopped, assist ventilation with a mechanical device or use
mouth-to-mouth resuscitation.
SKIN CONTACT
Wash contact areas with soap and water. Remove contaminated clothing. Launder contaminated clothing
before reuse. If product is injected into or under the skin, or into any part of the body, regardless of the
appearance of the wound or its size, the individual should be evaluated immediately by a physician as a
surgical emergency. Even though initial symptoms from high pressure injection may be minimal or absent, early
surgical treatment within the first few hours may significantly reduce the ultimate extent of injury.
EYE CONTACT
Flush thoroughly with water. If irritation occurs, get medical assistance.
INGESTION
First aid is normally not required. Seek medical attention if discomfort occurs.
SECTION 5 FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA
Appropriate Extinguishing Media: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish
flames.
Inappropriate Extinguishing Media: Straight streams of water
FIRE FIGHTING
Fire Fighting Instructions: Evacuate area. Prevent run-off from fire control or dilution from entering streams,
sewers or drinking water supply. Fire-fighters should use standard protective equipment and in enclosed
spaces, self-contained breathing apparatus (SCBA). Use water spray to cool fire exposed surfaces and to
protect personnel.
Hazardous Combustion Products: Smoke, Fume, Aldehydes, Sulphur Oxides, Incomplete combustion
products, Oxides of carbon
FLAMMABILITY PROPERTIES
Flash Point [Method]: >177C (351F) [ ASTM D-92]
Flammable Limits (Approximate volume % in air): LEL: 0.9 UEL: 7.0
Autoignition Temperature: N/D
SECTION 6 ACCIDENTAL RELEASE MEASURES
NOTIFICATION PROCEDURES
In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable
Product Name: MOBIL ATF 320
Revision Date: 03 Jul 2009
Page 3 of 8
______________________________________________________________________________________________________________________
regulations.
SPILL MANAGEMENT
Land Spill: Stop leak if you can do so without risk. Recover by pumping or with suitable absorbent.
Water Spill: Stop leak if you can do so without risk. Confine the spill immediately with booms. Warn other
shipping. Remove from the surface by skimming or with suitable absorbents. Seek the advice of a specialist
before using dispersants.
Water spill and land spill recommendations are based on the most likely spill scenario for this material;
however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction
and speed may greatly influence the appropriate action to be taken. For this reason, local experts should be
consulted. Note: Local regulations may prescribe or limit action to be taken.
ENVIRONMENTAL PRECAUTIONS
Large Spills: Dyke far ahead of liquid spill for later recovery and disposal. Prevent entry into waterways,
sewers, basements or confined areas.
SECTION 7 HANDLING AND STORAGE
HANDLING
Avoid contact with skin. Prevent small spills and leakage to avoid slip hazard.
Static Accumulator: This material is a static accumulator.
STORAGE
Do not store in open or unlabelled containers. Keep away from incompatible materials.
SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Exposure limits/standards for materials that can be formed when handling this product: When mists / aerosols
can occur, the following are recommended: 5 mg/m³ - ACGIH TLV, 10 mg/m³ - ACGIH STEL.
Note: Information about recommended monitoring procedures can be obtained from the relevant
agency(ies)/institute(s):
UK Health and Safety Executive (HSE)
ENGINEERING CONTROLS
The level of protection and types of controls necessary will vary depending upon potential exposure conditions.
Control measures to consider:
No special requirements under ordinary conditions of use and with adequate ventilation.
PERSONAL PROTECTION
Personal protective equipment selections vary based on potential exposure conditions such as applications,
handling practices, concentration and ventilation. Information on the selection of protective equipment for use
with this material, as provided below, is based upon intended, normal usage.
Product Name: MOBIL ATF 320
Revision Date: 03 Jul 2009
Page 4 of 8
______________________________________________________________________________________________________________________
Respiratory Protection: If engineering controls do not maintain airborne contaminant concentrations at a
level which is adequate to protect worker health, an approved respirator may be appropriate. Respirator
selection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types of
respirators to be considered for this material include:
No special requirements under ordinary conditions of use and with adequate ventilation.
For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode.
Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate,
gas/vapour warning properties are poor, or if air purifying filter capacity/rating may be exceeded.
Hand Protection: Any specific glove information provided is based on published literature and glove
manufacturer data. Glove suitability and breakthrough time will differ depending on the specific use conditions.
Contact the glove manufacturer for specific advice on glove selection and breakthrough times for your use
conditions. Inspect and replace worn or damaged gloves. The types of gloves to be considered for this material
include:
Chemical resistant gloves are recommended.
Eye Protection: If contact is likely, safety glasses with side shields are recommended.
Skin and Body Protection: Any specific clothing information provided is based on published literature or
manufacturer data. The types of clothing to be considered for this material include:
Chemical/oil resistant clothing is recommended.
Specific Hygiene Measures: Always observe good personal hygiene measures, such as washing after
handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective
equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned.
Practice good housekeeping.
ENVIRONMENTAL CONTROLS
See Sections 6, 7, 12, 13.
SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES
Typical physical and chemical properties are given below. Consult the Supplier in Section 1 for additional
data.
GENERAL INFORMATION
Physical State: Liquid
Colour: red
Odour: Characteristic
Odour Threshold: N/D
IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION
Relative Density (at 15 C): 0.856
Flash Point [Method]: >177C (351F) [ ASTM D-92]
Flammable Limits (Approximate volume % in air): LEL: 0.9 UEL: 7.0
Autoignition Temperature: N/D
Boiling Point / Range: > 316C (600F)
Vapour Density (Air = 1): > 2 at 101 kPa
Vapour Pressure: < 0.013 kPa (0.1 mm Hg) at 20°C
Product Name: MOBIL ATF 320
Revision Date: 03 Jul 2009
Page 5 of 8
______________________________________________________________________________________________________________________
Evaporation Rate (N-Butyl Acetate = 1): N/D
pH: N/A
Log Pow (n-Octanol/Water Partition Coefficient): > 3.5
Solubility in Water: Negligible
Viscosity: 37.8 cSt (37.8 mm²/sec) at 40°C | 7.9 cSt (7.9 mm²/sec) at 100C
Oxidising properties: See Sections 3, 15, 16.
OTHER INFORMATION
Freezing Point: N/D
Melting Point: N/A
Pour Point: -42°C (-44°F)
DMSO Extract (mineral oil only), IP-346: < 3 %wt
SECTION 10 STABILITY AND REACTIVITY
STABILITY: Material is stable under normal conditions.
CONDITIONS TO AVOID: Excessive heat. High energy sources of ignition.
MATERIALS TO AVOID: Strong oxidisers
HAZARDOUS DECOMPOSITION PRODUCTS: Material does not decompose at ambient temperatures.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 11 TOXICOLOGICAL INFORMATION
Acute Toxicity
Route of Exposure Conclusion / Remarks
INHALATION
Toxicity: LC50 > 5000 mg/m3 Minimally Toxic. Based on test data for structurally similar
materials.
Irritation: No end point data. Negligible hazard at ambient/normal handling temperatures.
Based on assessment of the components.
INGESTION
Toxicity: LD50 > 5000 mg/kg Minimally Toxic. Based on test data for structurally similar
materials.
Skin
Toxicity: LD50 > 5000 mg/kg Minimally Toxic. Based on test data for structurally similar
materials.
Irritation: Data available. Negligible irritation to skin at ambient temperatures. Based on test
data for structurally similar materials.
Eye
Irritation: Data available. May cause mild, short-lasting discomfort to eyes. Based on test
data for structurally similar materials.
CHRONIC/OTHER EFFECTS
Contains:
Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346, Modified
Product Name: MOBIL ATF 320
Revision Date: 03 Jul 2009
Page 6 of 8
______________________________________________________________________________________________________________________
Ames test, and/or other screening tests. Dermal and inhalation studies showed minimal effects; lung non-
specific infiltration of immune cells, oil deposition and minimal granuloma formation. Not sensitising in test
animals.
Additional information is available by request.
SECTION 12 ECOLOGICAL INFORMATION
The information given is based on data available for the material, the components of the material, and similar materials.
ECOTOXICITY
Material -- Not expected to be harmful to aquatic organisms.
MOBILITY
Base oil component -- Low solubility and floats and is expected to migrate from water to the land. Expected to
partition to sediment and wastewater solids.
PERSISTENCE AND DEGRADABILITY
Biodegradation:
Base oil component -- Expected to be inherently biodegradable
BIOACCUMULATION POTENTIAL
Base oil component -- Has the potential to bioaccumulate, however metabolism or physical properties may
reduce the bioconcentration or limit bioavailability.
SECTION 13 DISPOSAL CONSIDERATIONS
Disposal recommendations based on material as supplied. Disposal must be in accordance with current applicable
laws and regulations, and material characteristics at time of disposal.
DISPOSAL RECOMMENDATIONS
Product is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervised
incineration at very high temperatures to prevent formation of undesirable combustion products.
REGULATORY DISPOSAL INFORMATION
European Waste Code: 13 02 05
NOTE: These codes are assigned based upon the most common uses for this material and may not reflect
contaminants resulting from actual use. Waste producers need to assess the actual process used when
generating the waste and its contaminants in order to assign the proper waste disposal code(s).
This material is considered as hazardous waste pursuant to Directive 91/689/EEC on hazardous waste, and
subject to the provisions of that Directive unless Article 1(5) of that Directive applies.
Empty Container Warning Empty Container Warning (where applicable): Empty containers may contain residue and
can be dangerous. Do not attempt to refill or clean containers without proper instructions. Empty drums should be
Product Name: MOBIL ATF 320
Revision Date: 03 Jul 2009
Page 7 of 8
______________________________________________________________________________________________________________________
completely drained and safely stored until appropriately reconditioned or disposed. Empty containers should be taken
for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with
governmental regulations. DO NOT PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE
SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION.
THEY MAY EXPLODE AND CAUSE INJURY OR DEATH.
SECTION 14 TRANSPORT INFORMATION
LAND (ADR/RID) : Not Regulated for Land Transport
INLAND WATERWAYS (ADNR/ADN) : Not Regulated for Inland Waterways Transport
SEA (IMDG) : Not Regulated for Sea Transport according to IMDG-Code
AIR (IATA) : Not Regulated for Air Transport
SECTION 15 REGULATORY INFORMATION
Material is not dangerous as defined by the EU Dangerous Substances/Preparations Directives.
EU LABELING: Not regulated according to EC Directives
.
.
Contains: ALKOXYLATED LONG-CHAIN ALKYL AMINE, ALKYL ALKOXY AMINE, ALKYL DITHIADIAZOLE
May produce an allergic reaction. This material contains one or more sensitizers <1.0% by weight which are
not identified in the Composition Section.
REGULATORY STATUS AND APPLICABLE LAWS AND REGULATIONS
Complies with the following national/regional chemical inventory requirements: AICS, IECSC, DSL,
EINECS, KECI, PICCS, TSCA
SECTION 16 OTHER INFORMATION
N/D = Not determined, N/A = Not applicable
KEY TO THE RISK CODES CONTAINED IN SECTION 2 AND 3 OF THIS DOCUMENT (for information only):
R36; Irritating to eyes.
THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:
Revision Changes:
Section 09: Boiling Point ºC(ºF) was modified.
Section 09: n-Octanol/Water Partition Coefficient was modified.
Section 09: Flash Point ºC(ºF) was modified.
Section 09: Viscosity was modified.
Product Name: MOBIL ATF 320
Revision Date: 03 Jul 2009
Page 8 of 8
______________________________________________________________________________________________________________________
Section 14: Inland Waterways (ADNR) - Header was modified.
Section 16: RCode Key was modified.
Section 15: National Chemical Inventory Listing was modified.
Section 09: Relative Density was modified.
Section 15: Sensitiser Statement was modified.
Section 09: Viscosity was added.
-----------------------------------------------------------------------------------------------------------------------------------------------------
The information and recommendations contained herein are, to the best of ExxonMobil's knowledge and belief, accurate
and reliable as of the date issued. You can contact ExxonMobil to insure that this document is the most current
available from ExxonMobil. The information and recommendations are offered for the user's consideration and
examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer
repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is
included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to
handlers and users. Alteration of this document is strictly prohibited. Except to the extent required by law, re-
publication or retransmission of this document, in whole or in part, is not permitted. The term, "ExxonMobil" is used for
convenience, and may include any one or more of ExxonMobil Chemical Company, Exxon Mobil Corporation, or any
affiliates in which they directly or indirectly hold any interest.
-----------------------------------------------------------------------------------------------------------------------------------------------------
Internal Use Only
MHC: 0B, 0B, 0, 0, 0, 0 PPEC: C
DGN: 7040855XGB (547130)
-----------------------------------------------------------------------------------------------------------------------------------------------------
