Visual Index

Hydraulic Flanges
and Components

The Fitting Authority

4300 Catalog Hydraulic Flanges and Components

FCS FCC FHS3 FHS6

Flange Clamps – Split Flange Clamp – Captive Code 61 Flange Code 62 Flange
Clamps – Metric Clamps – Metric
Flange
Clamps

M7 M7 M8 M9
LOHQ XHQ BUHQ1 F5OHQ GFS
Code 61, 62 / ORFS Code 61, 62 / 37° Flare Code 61 / Flareless Code 61, 62 / SAE-ORB Code 61, 62 / Metric
Straight Flareless
Flange
Adapters /
Flanges
M10 M10 M10 M11 M12
BFG B3HQ P W7HQ G5HQ GHQ
DIN Flange / Metric Code 61, 62 / Flareless Flange Head Plug Flange Head / Pipe Flange Head / SAE-ORB Flange Head / NPT
Flareless Socket

M13 M11 M13 M14 M14 M14

WB1/3/5HQ1 WB3/5/7HQ2 G5Q GQ G4Q W5Q
Code 61 / Weld Butt Code 62 / Weld Butt Code 61, 62 / SAE-ORB Code 61, 62 / NPT Code 61, 62 / BSPP Code 61, 62 / Socket
– Pipe – Pipe – Pipe

M15 M15 M16 M16 M17 M18

W4Q W7Q W6Q WB1/3/5Q1 WB3/5/7Q2 AS
Code 61, 62 / Socket Code 61, 62 / Ext Socket Code 61, 62 / Ext Socket Code 61 / Weld Butt Code 62 / Weld Butt Code 61, 62 / Weld Butt
– Tube – Pipe – Tube – Pipe – Pipe – Tube Metric

M19 M20 M21 M22 M23 M24

WBT WSD GQS W5SQS PQ SPGG5
Code 61 / Weld Tank Code 61, 62 / Weld Square Flange / NPT Square Flange / Weld Code 61, 62 / Blank Flange Spacer w/Gage
Adapter Saddle Socket – Pipe Ports

M24 M25 M25 M26 M26 M27

CP LOVQ XVQ BUVQ1
Flange Connector Plate Code 61, 62 / ORFS Code 61, 62 / 37° Flare Code 61 / Flareless

45° Flange
Adapters

M27 M28 M28 M28

LOEQ XEQ BUEQ1 W7EQ WFS
Code 61, 62 / ORFS Code 61, 62 / 37° Flare Code 61 / Flareless Code 61, 62 / Weld Code 61, 62 / Metric
Socket – Pipe Flareless
90° Flange
Adapters

M29 M29 M29 M30 M31

M2 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

BFW G5EQ GEQ W6EQ

DIN Flange / Metric Code 61, 62 / SAE-ORB Code 61, 62 / NPT Code 61, 62 / Weld
Flareless Socket – Tube

90° Elbows

M32 M33 M34 M35

QPQPJQ G5Q GQ W5Q
Code 61, 62 Junction Tee Code 61, 62 / SAE-ORB Code 61, 62 / NPT Code 61, 62 / Weld
Socket – Pipe
Stainless
Tee Steel
Flanges
M33
M36 M36 M37
PQ
Code 61, 62 / Blank

M38

O-Rings and Seals (Shown in Section O)

Code 61/62 Flange ORFS O-Ring SAE 4-Bolt Flange
Seal O-Ring

O-Rings
and Seals

O9 O3 O9

Equipment (Shown in Section S)

Parflange 1050

Flanging
Tools

S24

M3 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

Introduction Flange Clamps — Clamps are used for providing the holding
power to the 4-bolt flange connection. They are offered in split
The 4-bolt flange connections conforming to SAE J518 and ISO and captive (one-piece) versions. The captive version is also of-
6162-1 and -2 are proven, leak-free connections, especially fered with either drilled or tapped bolt holes. The captive flange
suited for larger sizes, higher pressures and assembly in tight clamp with tapped holes is used while connecting a tube to
quarters. Threaded port connections such as SAE straight another tube or a hose.
thread O-ring and ISO 6149 are reasonably easy to assemble
Parker flange clamps are forged for higher strength and durability.
and provide 6000 psi and higher pressure capability up to size
They meet all requirements of SAE J518. The split clamps make
12 (M27). Beyond this size the pressure rating starts to decrease
it easy to assemble the connection in close quarters. They also
and assembly torques increase rapidly. The 4-bolt flange port
make removal of the flange head component, such as a hose
connections provide ability to connect larger sizes and achieve
assembly, easy by loosening all four bolts and removing one
higher-pressure capability at reasonable assembly torques. Be-
clamp half, as shown in Fig. M2.
cause of the lower assembly torques compared to an equivalent
size threaded port, these connections are well suited for tight
quarters where wrench clearances are limited. Parker 4-bolt
flange products described in this part of the catalog provide
various means of connecting tubes, hoses, pipes and threaded
fittings to 4-bolt flange ports. The discussion below provides an Parflange Sleeve
overview of some of the available flange products.
Code 61/62 Clamp

Design and Construction

Parker 4-bolt flange products are designed to provide different
methods of connecting a tube, hose, pipe or another fitting to Seal Plate
the SAE standard 4-bolt flange port.
Flange Fittings — All Parker flange fittings, except for those
with square mounting hole patterns (nomenclature code QS),
are designed to conform to O-ring groove, bolt holes and bolt
pattern dimensions of either Code 61 or Code 62 of SAE J518
and ISO 6162-1 (Code 61) or -2 (Code 62). Fig. M2 – Assembly / Removal SAE J518 Connection
The flange adapters (Code Q1 and Q2), and flange block fittings
(Codes Q1B, Q2B and QSB) have O-ring grooves conforming Junction Block Tees — These are solid block union fittings to
to dimensions in SAE J518. The flange block fittings (Codes connect two tube/hose assemblies using 4-bolt flange connec-
Q1B and Q2B) have through holes for the mounting bolts, again tion, at a junction, to SAE 4-bolt flange port, or three tube/hose
conforming to SAE J518. There is no industry standard for the assemblies to each other.
bolt pattern of the square pattern block flanges with codes QSP
Connector Plate — Connector plate is used as a middle plate
and QSB.
to connect two flange heads with O-ring grooves, such as two
The flange pad fittings (Codes Q1P, Q2P, and QSP) have a flat hose assemblies with flange connection ends. The flat surface
face (no O-ring groove) and the mounting holes are tapped. of the plate provides sealing surface on each side for the O-ring
Where these fittings are used, the seal is in the mating part housed in the hose ends.
(flange adapter, flange hose fitting, flange block fitting, etc.) as
Spacer Plate — Spacer plate provides access to the system
shown in Fig. M1.
fluid via the gage port on the side. The plate is between the
flange connection to provide this access.
Plugs — Plugs provide a means to block off the 4-bolt flange
port with and without clamps, and to plug the end of a pipe (via
welding).
Tank Weld Adapter — Tank weld adapters provide a means of
flange connection to a fabricated reservoir or tank.
Steel Stainless Steel
Hydraulic Flanges
ASTM Type ASTM Type
Flanged Hose Fitting 4-Bolt Flanges A108 C1020 A240 316L
Flange Pad A351 / Nitronic
Flange Clamps A108 C1045
Fitting A743 50
O-ring Seal in Hose Fitting
HHCS Bolts SAE Grade 8 — —
SHCS Bolts — — A240 316
Fig. M1 – Flange Pad Fitting
Dimensions other than the O-ring groove, bolt holes, bolt pat- Table M1 – Standard Material Specifications for Hydraulic
tern, and the flange foot print (for codes Q1B and Q2B only) Flanges and Components
are not governed by any industry standard. However, Parker Note: Split flange clamps are zinc clear (or Cr6 free) chromate. All
product design follows common industry practice and sound other steel flanges are oil dipped.
engineering.

M4 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

How Flange Connections Work

The four-bolt flange connection (SAE J518) is a proven leak-free Clamping Bolt
connection, especially suited for larger sizes. As a result, it has
achieved worldwide acceptance.
Code 61/62 Clamp
The connection’s success is in its simplicity. It is a static face
seal using a high durometer O-ring for the seal and clamps
and bolts for holding power as shown in Fig. M3. Alternatively,
a bonded seal plate is between the port face and the flat face of
a mechanically formed (flanged with Parflange® process) tube Tube or Hose End
as shown in Fig. M4 to achieve the same results.
Flange Head
The (O-ring) seal is compressed between the bottom of the
groove in the flange head and the flat surface of the port or O-Ring
flange pad, providing a reliable soft seal. The alternate seal plate
has a high durometer bonded rubber seal on the inside edge,
which compresses between the two flat surfaces, providing a
soft seal with the same reliability. A metal-to-metal contact at
the outer face of the flange with the port face keeps the seal
from extruding under pressure. This metal-to-metal contact is
maintained by the clamping force provided by tightening the
bolts via the clamps.
This simple design provides several advantages over threaded Fig. M3 – Four-Bolt Flange Connection (SAE J518)
port connections, such as NPTF, SAE, BSPP, ISO 6149, etc.,
in larger sizes:
• Ability to connect up to 5 inch O.D tube (Code 61
only)
• Much lower tightening torque required from the four
bolts compared to that required for equivalent size
threaded port
• Less tightening torque means smaller wrenches and
wrench swing clearances — providing ease of as-
Code 61/62 Clamp
sembly in tight quarters
• Up to 6000 psi capability through 2” size (Code 62
only) Tube

• Single seal point between tube/pipe/hose assembly

and the port Parflange Sleeve

• Ease of disassembly through use of split clamps

Seal Plate
The connection has one disadvantage — it requires a larger
area (foot print) on the component than an equivalent threaded
port.

Assembly and Installation

Fig. M4 – Formed Tube with ISO 6162 (SAE J518) Connection
Please refer to Section T for the assembly and installation instruc-
tions for Hydraulic Flanges and Components fittings.

Feature Advantage Benefit

Conform to SAE J518 and Controls dimensions and tolerances of code 61 and
Insures interchangeability and consistency
ISO 6162 62 port connections
Reliable, long life performance No downtime, reduced costs
Forged Construction
Compact envelope size, no sharp edges Reduced weight
Over 60 Configurations Flexibility in plumbing, match system needs Best solution and best value
Eliminates messy and time consuming brazing
Parflange Technology Designed to be used with Code 61/62 fittings
process
Performs in rigorous applications for the life of the
Mounting Hardware Grade 8 bolts standard
flange
Flange with hardware for mounting (o-ring, bolts and
Flange Kits Reduces order and assembly error
lockwashers)

Dimensions and pressures for reference only, subject to change.

M5 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

Code 61 and Code 62 Port Ends Return

To
Catalog

Flange Flange
O.D. Drill Height
C D Max E
SIZE (inch) (inch) (inch)
CODE 61
8 1.19 0.50 0.265
12 1.50 0.75 0.265
16 1.75 1.00 0.315
20 2.00 1.25 0.315
24 2.38 1.50 0.315
32 2.81 2.00 0.375
CODE 62
8 1.25 0.50 0.305
12 1.63 0.75 0.345
16 1.88 1.00 0.375
20 2.13 1.25 0.405
24 2.50 1.50 0.495
32 3.13 2.00 0.495

Dimensions and pressures for reference only, subject to change.

M6 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

FCS
Code 61/62 Flange Clamps, Split

How To
Order

STANDARD Specs
TUBE HOSE HOSE K Dynamic
FITTING PRODUCTS PRODUCTS FLANGE DRILL MOUNTING Pressure
PART # PART # PART # SIZE B D E H DIA. L M N Y HARDWARE (x 1,000 PSI)
FLANGE HALF FLANGE HALF KIT (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) HHCS S SS
CODE 61 FLANGE CLAMPS, SPLIT Assembly /
8FCS1 51H-8 5151HK-8 0.50 2.12 0.955 0.50 1.22 0.344 0.75 0.245 0.86 1.50 5/16-18 x 1.25 5.0 5.0 Installation
12FCS1 51H-12 5151HK-12 0.75 2.56 1.265 0.56 1.53 0.406 0.88 0.245 0.98 1.88 3/8-16 x 1.25 5.0 5.0
16FCS1 51H-16 5151HK-16 1.00 2.75 1.515 0.62 1.78 0.406 0.94 0.295 1.11 2.06 3/8-16 x 1.25 5.0 5.0
20FCS1 51H-20 5151HK-20 1.25 3.12 1.720 0.56 2.03 0.469 0.88 0.295 1.39 2.31 7/16-14 x 1.50 4.0 4.0
24FCS1 51H-24 5151HK-24 1.50 3.69 2.000 0.62 2.41 0.531 1.00 0.295 1.58 2.75 1/2-13 x 1.50 3.0 3.0 Reference
32FCS1 51H-32 5151HK-32 2.00 4.00 2.470 0.62 2.84 0.531 1.03 0.355 1.86 3.06 1/2-13 x 1.50 3.0 3.0 Section
40FCS1 51H-40 5151HK-40 2.50 4.50 2.950 0.75 3.34 0.531 1.50 0.355 2.09 3.50 1/2-13 x 1.75 2.5 2.5
48FCS1 51H-48 5151HK-48 3.00 5.31 3.580 0.88 4.03 0.656 1.62 0.355 2.53 4.19 5/8-11 x 1.75 2.0 2.0
56FCS1 51H-56 5151HK-56 3.50 6.00 4.030 0.88 4.53 0.656 1.12 0.422 2.70 4.75 5/8-11 x 1.75 0.5 0.5
64FCS1 51H-64 5151HK-64 4.00 6.38 4.530 1.00 5.03 0.656 1.38 0.422 2.95 5.13 5/8-11 x 2.00 0.5 0.5
CODE 62 FLANGE CLAMPS, SPLIT
12FCS2 HFH-12 HFHFHK-12 0.75 2.81 1.280 0.75 1.66 0.406 1.12 0.325 1.14 2.00 3/8-16 x 1.50 6.0 6.0
16FCS2 HFH-16 HFHFHK-16 1.00 3.19 1.530 0.94 1.91 0.469 1.31 0.355 1.33 2.25 7/16-14 x 1.75 6.0 6.0
20FCS2 HFH-20 HFHFHK-20 1.25 3.75 1.750 1.06 2.16 0.531 1.50 0.385 1.48 2.63 1/2-13 x 1.75 6.0 6.0
24FCS2 HFH-24 HFHFHK-24 1.50 4.44 2.030 1.19 2.53 0.656 1.69 0.475 1.83 3.13 5/8-11 x 2.25 6.0 6.0
32FCS2 HFH-32 HFHFHK-32 2.00 5.25 2.660 1.44 3.16 0.781 2.06 0.475 2.20 3.81 3/4-10 x 2.75 6.0 6.0

To order a flange clamp split kit, insert a “K” after the material designator in the Tube Fitting part number. The
Kit includes two flange clamp halves, 4 HHCS bolts, 4 lock washers and an O-ring.

FCC
Code 61/62 Flange Clamp, Captive

STANDARD
Dynamic
TUBE FITTING K MOUNTING Pressure
PART # FLANGE DRILL T HARDWARE (x 1,000 PSI)
DRILLED TAPPED SIZE A B D E H DIA. L M TAP X Y
HOLES HOLES (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UN-2B (in.) (in.) HHCS SX SS
CODE 61 FLANGE CLAMP, CAPTIVE
8FCC1 8FCCT1 0.50 1.81 2.125 0.955 0.50 1.219 0.344 0.75 0.245 5/16-18 0.688 1.500 5/16-18 x 1.25 5.0
12FCC1 12FCCT1 0.75 2.06 2.560 1.265 0.56 1.531 0.406 0.88 0.245 3/8-16 0.875 1.875 3/8-16 x 1.25 5.0
16FCC1 16FCCT1 1.00 2.31 2.750 1.515 0.62 1.781 0.406 0.94 0.295 3/8-16 1.031 2.062 3/8-16 x 1.25 5.0
20FCC1 20FCCT1 1.25 2.88 3.125 1.720 0.56 2.031 0.469 0.88 0.295 7/16-14 1.188 2.312 7/16-14 x 1.50 4.0
24FCC1 24FCCT1 1.50 3.25 3.705 2.000 0.62 2.406 0.531 1.00 0.295 1/2-13 1.406 2.750 1/2-13 x 1.50 3.0
32FCC1 32FCCT1 2.00 3.81 4.000 2.470 0.62 2.844 0.531 1.03 0.355 1/2-13 1.688 3.062 1/2-13 x 1.50 3.0
40FCC1 40FCCT1 2.50 4.28 4.500 2.950 0.75 3.344 0.531 1.50 0.355 1/2-13 2.000 3.500 1/2-13 x 1.75 2.5
48FCC1 48FCCT1 3.00 5.16 5.315 3.580 0.88 4.031 0.656 1.62 0.355 5/8-11 2.438 4.188 5/8-11 x 1.75 2.0
56FCC1 56FCCT1 3.50 5.50 6.000 4.030 0.88 4.531 0.656 1.12 0.422 5/8-11 2.750 4.750 5/8-11 x 1.75 0.5
64FCC1 64FCCT1 4.00 6.00 6.375 4.530 1.00 5.031 0.656 1.38 0.422 5/8-11 3.062 5.125 5/8-11 x 2.00 0.5
CODE 62 FLANGE CLAMP, CAPTIVE
12FCC2 12FCCT2 0.75 2.38 2.810 1.280 0.75 1.656 0.406 1.12 0.325 3/8-16 0.938 2.000 3/8-16 x 1.50 6.0
16FCC2 16FCCT2 1.00 2.75 3.190 1.530 0.94 1.906 0.469 1.31 0.355 7/16-14 1.094 2.250 7/16-14 x 1.75 6.0
20FCC2 20FCCT2 1.25 3.06 3.750 1.750 1.06 2.156 0.531 1.50 0.385 1/2-13 1.250 2.625 1/2-13 x 1.75 6.0
24FCC2 24FCCT2 1.50 3.75 4.440 2.030 1.19 2.531 0.656 1.69 0.475 5/8-11 1.438 3.125 5/8-11 x 2.25 6.0
32FCC2 32FCCT2 2.00 4.50 5.250 2.660 1.44 3.156 0.781 2.06 0.475 3/4-10 1.750 3.8120 3/4-10 x 2.75 6.0

Dimensions and pressures for reference only, subject to change.

M7 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

FHS3
Flange Components

How To
Order

Specs

Assembly /
Code 61 Installation

For Straights and Elbows

(ISO 6162-1, Type 1)
Reference
Section
For Working SAE 4 Socket Head For
Tube O.D. Pressure Flange Cap Screws Tube O.D. A B
Size Series (bar) Halves DIN 912-8.8 O-Ring Size Series ~
~ ~
~ a b
1/2 15L 315 FHS 32A3CX M8X30 OR18.64 x 3.53X 1/2 15L 54 46 38.1 17.5
1/2 16S 350 1/2 16S 54 46 38.1 17.5
3/4 18L 315 FHS 33A3CX M10X35 OR25.00 x 3.53X 3/4 18L 65 52 47.6 22.2
3/4 22L 160 3/4 22L 65 52 47.6 22.2
3/4 20S 350 3/4 20S 65 52 47.6 22.2
3/4 25S 350 3/4 25S 65 52 47.6 22.2
1 28L 160 FHS 34A3CX M10X35 OR32.92 x 3.53X 1 28L 70 59 52.4 26.2
1 30S 350 1 30S 70 59 52.4 26.2
1 1/4 35L 160 FHS 35A3CX M12X40* OR37.70 x 3.53X 1 1/4 35L 79 73 58.7 30.2
1 1/4 25S 280 1 1/4 25S 79 73 58.7 30.2
1 1/4 30S 280 1 1/4 30S 79 73 58.7 30.2
1 1/4 38S 280 1 1/4 38S 79 73 58.7 30.2
1 1/2 42L 160 FHS 36A3CX M12X40 OR47.22 x 3.53X 1 1/2 42L 94 83 69.9 35.7
1 1/2 38S 210 1 1/2 38S 94 83 69.9 35.7

Temperature range without pressure reductions for fittings with O-ring sealing of NBR (e.g., buna N series) -35°C up to
+100°C, FPM (e.g., fluorocarbon on request) -25°C up to +120°C.
Tightening torques for socket head cap screws see Table T6.
* Does not meet ISO 6162 specification.

Dimensions and pressures for reference only, subject to change.

M8 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

FHS6
Flange Components

How To
Order

Specs

Assembly /
Code 62 Installation

For Straights and Elbows

(ISO 6162-2, Type 1)
Reference
Section
For Working SAE 4 Socket Head For
Tube O.D. Pressure Flange Cap Screws Tube O.D. A B
Size Series (bar) Halves DIN 912-8.8 O-Ring Size Series ~
~ a ~
~ b
1/2 16S 400 FHS 62A3CX M8X35 OR18.64 x 3.53X 1/2 16S 56 40.5 47 18.2
3/4 16S 400 FHS 63A3CX M10X35 OR25.00 x 3.53X 3/4 16S 71 50.8 60 23.8
3/4 20S 400 FHS 63A3CX M10X35 OR25.00 x 3.53X 3/4 20S 71 50.8 60 23.8
3/4 25S 400 FHS 63A3CX M10X35 OR25.00 x 3.53X 3/4 25S 71 50.8 60 23.8
1 25S 400 FHS 64A3CX M12X45 OR32.92 x 3.53X 1 25S 81 57.2 70 27.8
1 30S 400 FHS 64A3CX M12X45 OR32.92 x 3.53X 1 30S 81 57.2 70 27.8
1 1/4 30S 400 FHS 65A3CX M14X50* OR37.70 x 3.53X 1 1/4 30S 95 66.7 77 31.8
1 1/4 38S 315 FHS 65A3CX M14X50* OR37.70 x 3.53X 1 1/4 38S 95 66.7 77 31.8
1 1/2 38S 315 FHS 66A3CX M16X55 OR47.22 x 3.53X 1 1/2 38S 113 79.4 95 36.5

Temperature range without pressure reductions for fittings with O-ring sealing of NBR (e.g., buna N series) -35° up to
+100°C, FPM (e.g., fluorocarbon on request) -25° up to +120°C.
Tightening torques for socket head cap screws see Table T7.
* Does not meet ISO 6162 specification.

Dimensions and pressures for reference only, subject to change.

M9 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

LOHQ1 LOHQ2
Code 61 Flange Connector Code 62 Flange Connector
Code 61 / ORFS Code 62 / ORFS
How To
Order
* Y – Across Wrench Flats * Y – Across Wrench Flats

STANDARD STANDARD
Dynamic Dynamic Specs
TUBE END SIZE Pressure TUBE END SIZE Pressure
FITTING 1 2 C E L Y (x 1,000 PSI) FITTING 1 2 C E L Y (x 1,000 PSI)
PART # (in.) Code 61 (in.) (in.) (in.) (in.) -S PART # (in.) Code 62 (in.) (in.) (in.) (in.) -S
12 LOHQ1 3/4 3/4 1.500 0.265 2.79 1 3/8 5.0 12 LOHQ2 3/4 3/4 1.625 0.345 3.02 1 3/8 6.0 Assembly /
16 LOHQ1 1 1 1.750 0.315 2.81 1 5/8 5.0 12-16 LOHQ2 3/4 1 1.875 0.375 3.34 1 5/8 6.0 Installation
20 LOHQ1 1 1/4 1 1/4 2.000 0.315 3.21 1 7/8 4.0 16 LOHQ2 1 1 1.875 0.375 3.36 1 5/8 6.0
24 LOHQ1 1 1/2 1 1/2 2.375 0.315 3.29 2 1/8 3.0 20 LOHQ2 1 1/4 1 1/4 2.125 0.405 3.48 1 7/8 5.0
24 LOHQ2 1 1/2 1 1/2 2.500 0.495 4.14 2 1/8 4.5
Reference
Section

XHQ1 XHQ2
Code 61 Flange Connector Code 62 Flange Connector
Code 61 / 37° Flare Code 62 / 37° Flare

* Y – Across Wrench Flats * Y – Across Wrench Flats

STANDARD STANDARD
Dynamic Dynamic
TUBE END SIZE Pressure TUBE END SIZE Pressure
FITTING 1 2 C E L Y (x 1,000 PSI) FITTING 1 2 C E L Y (x 1,000 PSI)
PART # (in.) Code 61 (in.) (in.) (in.) (in.) -S PART # (in.) Code 62 (in.) (in.) (in.) (in.) -S
12 XHQ1 3/4 3/4 1.500 0.265 2.77 1 3/8 5.0 12 XHQ2 3/4 3/4 1.625 0.345 3.08 1 3/8 5.0
16 XHQ1 1 1 1.750 0.315 2.91 1 5/8 5.0 16 XHQ2 1 1 1.875 0.375 3.43 1 5/8 5.0
20 XHQ1 1 1/4 1 1/4 2.000 0.315 3.36 1 7/8 4.0 20 XHQ2 1 1/4 1 1/4 2.125 0.405 3.60 1 7/8 4.0
24 XHQ1 1 1/2 1 1/2 2.375 0.315 3.57 2 1/8 3.0 24 XHQ2 1 1/2 1 1/2 2.500 0.495 4.34 2 1/8 3.0
32 XHQ1 2 2 2.812 0.375 4.04 2 5/8 2.0

BUHQ1
Code 61 Connector
Code 61 / Flareless

STANDARD
Dynamic
TUBE END SIZE Pressure
FITTING 1 2 C E L (x 1,000 PSI)
PART # (in.) Code 61 (in.) (in.) (in.) -S
12 BUHQ1 3/4 3/4 1.500 0.265 1.82
16 BUHQ1 1 1 1.750 0.315 1.88
20 BUHQ1 1 1/4 1 1/4 2.000 0.315 1.82
24 BUHQ1 1 1/2 1 1/2 2.375 0.315 1.94
32 BUHQ1 2 2 2.812 0.375 1.97

Dimensions and pressures for reference only, subject to change.

M10 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

F5OHQ1 F5OHQ2
Code 61 Connector Code 62 Connector
Code 61 / SAE-ORB Code 62 / SAE-ORB
How To
Order
* Y – Across Wrench Flats * Y – Across Wrench Flats

STANDARD STANDARD
Dynamic Dynamic Specs
TUBE END SIZE Pressure TUBE END SIZE Pressure
FITTING 1 2 C E L Y (x 1,000 PSI) FITTING 1 2 C E L Y (x 1,000 PSI)
PART # (in.) Code 61 (in.) (in.) (in.) (in.) -S PART # (in.) Code 62 (in.) (in.) (in.) (in.) -S
12 F5OHQ1 3/4 3/4 1.500 0.265 2.63 1 3/8 5.0 12 F5OHQ2 3/4 3/4 1.625 0.345 3.08 1 3/8 6.0
Assembly /
16 F5OHQ1 1 1 1.750 0.315 2.73 1 5/8 4.5 16 F5OHQ2 1 1 1.875 0.375 3.25 1 5/8 5.5 Installation
20 F5OHQ1 1 1/4 1 1/4 2.000 0.315 3.13 1 7/8 4.0 20 F5OHQ2 1 1/4 1 1/4 2.125 0.405 3.37 1 7/8 4.5
24 F5OHQ1 1 1/2 1 1/2 2.375 0.315 3.22 2 1/8 3.0 24 F5OHQ2 1 1/2 1 1/2 2.500 0.495 3.99 2 1/8 4.0
32 F5OHQ1 2 2 2.812 0.375 3.49 2 3/4 3.0 32 F5OHQ2 2 2 3.125 0.495 4.86 2 3/4 3.0
Reference
Section

B3HQ
Braze Flange Head Connector, Tube
Tube Braze Socket* / Code 61/62 Flange Head
* For clearance brazing

O-ring Face Flat Face

STANDARD
Dynamic
TUBE FITTING FLANGE TUBE Pressure
PART # SIZE O.D. C D F J L R S (x 1,000 PSI)
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) SX SS
TUBE BRAZE SOCKET / CODE 61 FLANGE HEAD
8B3HQ1 8B3HQ1N 0.50 1/2 0.265 0.406 1.188 0.312 0.50 0.940 0.502 5.0
10-8B3HQ1 10-8B3HQ1N 0.50 5/8 0.265 0.500 1.188 0.312 0.50 0.940 0.625 5.0
12B3HQ1 12B3HQ1N 0.75 3/4 0.265 0.656 1.500 0.375 0.56 1.250 0.752 4.5
16-12B3HQ1 16-12B3HQ1N 0.75 1 0.315 0.750 1.500 0.375 0.56 1.250 1.002 4.5
16B3HQ1 16B3HQ1N 1.00 1 0.315 0.906 1.750 0.375 0.56 1.500 1.002 4.5
20-16B3HQ1 20-16B3HQ1N 1.00 1 1/4 0.315 1.000 1.750 0.375 0.56 1.500 1.252 4.0
20B3HQ1 20B3HQ1N 1.25 1 1/4 0.315 1.125 2.000 0.375 0.56 1.700 1.252 3.5
24-20B3HQ1 24-20B3HQ1N 1.25 1 1/2 0.315 1.250 2.000 0.375 0.56 1.700 1.502 3.5
24B3HQ1 24B3HQ1N 1.50 1 1/2 0.315 1.375 2.380 0.438 0.62 1.980 1.502 3.0
28-24B3HQ1 28-24B3HQ1N 1.50 1 3/4 0.315 1.500 2.380 0.438 0.62 1.980 1.752 2.7
32B3HQ1 32B3HQ1N 2.00 2 0.375 1.875 2.810 0.500 0.62 2.450 2.002 3.0
36-32B3HQ1 36-32B3HQ1N 2.00 2 1/4 0.375 2.000 2.810 0.500 0.62 2.450 2.252 3.0
40B3HQ1 40B3HQ1N 2.50 2 1/2 0.375 2.375 3.312 0.562 0.68 2.921 2.502 2.2
44-40B3HQ1 44-40B3HQ1N 2.50 2 3/4 0.375 2.500 3.312 0.500 0.68 2.921 2.752 2.2
48B3HQ1 48B3HQ1N 3.00 3 0.375 2.875 4.000 0.562 0.75 3.546 3.002 1.7
TUBE BRAZE SOCKET / CODE 62 FLANGE HEAD
12B3HQ2 12B3HQ2N 0.75 3/4 0.345 0.656 1.625 0.500 0.69 1.250 0.752 6.0
16-12B3HQ2 16-12B3HQ2N 0.75 1 0.345 0.750 1.625 0.500 0.69 1.250 1.002 6.0
16B3HQ2 16B3HQ2N 1.00 1 0.375 0.810 1.875 0.625 0.81 1.500 1.002 6.0
20-16B3HQ2 20-16B3HQ2N 1.00 1 1/4 0.375 1.000 1.875 0.625 0.81 1.500 1.252 6.0
20B3HQ2 20B3HQ2N 1.25 1 1/4 0.405 1.010 2.125 0.812 1.00 1.718 1.252 6.0
24-20B3HQ2 24-20B3HQ2N 1.25 1 1/2 0.405 1.250 2.125 0.812 1.00 1.718 1.502 5.5
24B3HQ2 24B3HQ2N 1.50 1 1/2 0.495 1.250 2.500 1.000 1.19 2.000 1.502 6.0
28-24B3HQ2 28-24B3HQ2N 1.50 1 3/4 0.495 1.500 2.500 1.000 1.19 2.000 1.752 4.5
32B3HQ2 32B3HQ2N 2.00 2 0.495 1.750 3.125 1.375 1.50 2.620 2.002 5.5
36-32B3HQ2 36-32B3HQ2N 2.00 2 1/4 0.495 2.000 3.125 1.312 1.50 2.620 2.252 4.0

Dimensions and pressures for reference only, subject to change.

M11 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

GFS
SAE Flange Connector – Standard Series
Code 61 & 62 / Metric Flareless
How To
Order
STANDARD STANDARD
TUBE TUBE WORKING L1 MATERIAL EO-2
FITTING SIZE O.D. PRESSURE M d1 i I1 ≈ S1 ~
~
S2 S6 FROM STOCK FROM STOCK
PART # (in.) (mm) (bar) THREAD (mm) (mm) (mm) (mm) (mm) (mm) (mm) A3C 71 A3C 71 Specs
SAE FLANGE CONNECTIONS – CODE 61 – STANDARD SERIES
GFS32/15LA3C 1/2 15L 200 M22 x 1.5 12 11.5 41 56 24 27 6 · ·
GFS32/16SA3C 1/2 16S 220 M24 x 1.5 12 11.5 41.5 60 24 30 6 · ·
GFS33/18LA3C 3/4 18L 200 M26 x 1.5 15 15.5 45.5 62 30 32 8 · · Assembly /
GFS33/22LA3C 3/4 22L 100 M30 x 2 19 15.5 45.5 62 30 36 8 · · Installation
GFS33/20SA3C 3/4 20S 220 M30 x 2 16 15.5 46.5 68 30 36 8 · ·
GFS33/25SA3C 3/4 25S 220 M36 x 2 17 15.5 45 69 30 46 8 · ·
GFS34/28LA3C 1 28L 100 M36 x 2 24 13.5 46.5 63 36 41 8 · ·
GFS34/30SA3C 1 30S 220 M42 x 2 24 13.5 49.5 76 36 50 8 · · Reference
GFS35/35LA3C 1 1/4 35L 100 M45 x 2 30 18.5 47.5 69 41 50 8 · · Section
GFS35/25SA3C 1 1/4 25S 175 M36 x 2 20 18.5 48 72 41 46 8 · ·
GFS35/30SA3C 1 1/4 30S 175 M42 x 2 25 18.5 48.5 75 41 50 8 · ·
GFS35/38SA3C 1 1/4 38S 175 M52 x 2 28 18.5 50 81 46 60 8 · ·
GFS36/42LA3C 1 1/2 42L 100 M52 x 2 36 18.5 53 76 46 60 10 · ·
GFS36/38SA3C 1 1/2 38S 130 M52 x 2 32 18.5 54 85 46 60 10 · ·
SAE FLANGE CONNECTIONS – CODE 62 – HIGH PRESSURE SERIES
GFS62/16SA3C 1/2 16S 250 M24 x 1.5 12 13.5 44.5 63 24 30 6 · ·
GFS63/16SA3C 3/4 16S 250 M24 x 1.5 12 15.5 50.5 69 30 30 8 · ·
GFS63/20SA3C 3/4 20S 250 M30 x 2 16 15.5 50.5 72 30 36 8 · ·
GFS63/25SA3C 3/4 25S 250 M36 x 2 17 15.5 51 75 30 46 8 · ·
GFS64/25SA3C 1 25S 250 M36 x 2 20 20.5 60 84 36 46 10 · ·
GFS64/30SA3C 1 30S 250 M42 x 2 24 20.5 60.5 87 36 50 10 · ·
GFS65/30SA3C 1 1/4 30S 250 M42 x 2 25 22.5 65.5 92 41 50 10 · ·
GFS65/38SA3C 1 1/4 38S 200 M52 x 2 30 22.5 67 98 46 60 10 · ·
GFS66/38SA3C 1 1/2 38S 200 M52 x 2 30 24.5 73 104 46 60 14 · ·

EO-2 Part Number example: GFS33/18ZLA3C

Temperature range without pressure reductions for fittings with O-ring sealing of NBR (e.g., buna N series) -35°C up to +100°C,
FPM (e.g., fluorocarbon on request) -25°C up to +120°C.
Tightening torques for socket head cap screws see Tables T6 and T7.

Dimensions and pressures for reference only, subject to change.

M12 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

BFG
DIN Flange / Metric Flareless
Tube connection according to DIN 2353
How To
Order

STANDARD STANDARD
TUBE WORKING TUBE MATERIAL EO-2
Specs
FITTING PRESSURE O.D. d i I1 I2 L1 L2 LK S2 FROM STOCK FROM STOCK
PART # (bar) (mm) (mm) G (mm) (mm) (mm) (mm) (mm) (mm) (mm) A3C 71 A3C 71
BFG15L/LK40A3C 65 15 12 M 6 12.5 35 7 42 43 40 27 • •
BFG18L/LK40A3C 65 18 15 M 6 12.5 35 7.5 42 44 40 32 • •
BFG22L/LK40A3C 65 22 19 M 6 12.5 35 7.5 42 44.5 40 36 • • Assembly /
BFG15L/LK35A3C 155 15 12 M 6 12.5 30 7 39 38 35 27 • • Installation
BFG10L/LK35A3C 200 10 8 M 6 12.5 30 7 39 39 35 19 • •
BFG12L/LK35A3C 200 12 10 M 6 12.5 30 7 39 39 35 22 • •
Reference
Section
Unassembled BFG Fitting Components
1 3 5 6
Straight 2 Progressive 4 Cap Screws Spring Washer
Body Nut Ring O-Ring DIN 912-8.8 (4 pcs.) DIN 127 (4 pcs.)
BFG15L/LK40A3CX M15LA3CX DPR15LA3CX OR26X2.5X M6X22 A6
BFG15L/LK40A3CX M18LA3CX DPR18LA3CX OR26X2.5X M6X22 A6
BFG22L/LK40A3CX M22LA3CX DPR22LA3CX OR26X2.5X M6X22 A6
BFG15L/LK35A3CX M15LA3CX DPR15LA3CX OR20X2.5X M6X22 A6
BFG10L/LK35A3CX M10LA3CX DPR10LA3CX OR20X2.5X M6X22 A6
BFG12L/LK35A3CX M12LA3CX DPR12LA3CX OR20X2.5X M6X22 A6
EO-2 Part Number example: BFG15ZL/LK40A3C
Temperature range without pressure reductions for fittings with O-ring sealing of NBR
(e.g., buna N series) -35°C up to +100°C, FPM (e.g., fluorocarbon on request) -25°C up to 120°C.
Tightening torques for socket head cap screws see Table T6.

P
Flange Head Plug
Code 61/62 Flange Head Plug

O-ring Face Flat Face

STANDARD
Dynamic
TUBE FITTING FLANGE Pressure
PART # SIZE C F L R (x 1,000 PSI)
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) SX SS
CODE 61 FLANGE HEAD PLUG
8PQ1 8PQ1N 0.50 0.265 1.188 0.500 0.940 5.0
12PQ1 12PQ1N 0.75 0.265 1.500 0.560 1.250 5.0
16PQ1 16PQ1N 1.00 0.315 1.750 0.560 1.500 5.0
20PQ1 20PQ1N 1.25 0.315 2.000 0.560 1.700 4.0
24PQ1 24PQ1N 1.50 0.315 2.380 0.620 1.980 3.0
32PQ1 32PQ1N 2.00 0.375 2.810 0.620 2.450 3.0
40PQ1 40PQ1N 2.50 0.375 3.312 0.680 2.921 2.5
48PQ1 48PQ1N 3.00 0.375 4.000 0.750 3.546 2.0
CODE 62 FLANGE HEAD PLUG
12PQ2 12PQ2N 0.75 0.345 1.625 0.687 1.250 6.0
16PQ2 16PQ2N 1.00 0.375 1.875 0.812 1.500 6.0
20PQ2 20PQ2N 1.25 0.405 2.125 1.000 1.718 6.0
24PQ2 24PQ2N 1.50 0.495 2.500 1.187 2.000 6.0
32PQ2 32PQ2N 2.00 0.495 3.125 1.500 2.620 6.0

Dimensions and pressures for reference only, subject to change.

M13 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

W7HQ
Weld Socket Flange Connector, Pipe
Extended Weld Socket, Pipe / Code 61 or 62 Flange Head
How To
Order

STANDARD
Dynamic
TUBE PIPE FLANGE Pressure
Specs
FITTING SIZE SIZE C D F H L P R S (x 1,000 PSI)
PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) SX SS
EXTENDED WELD SOCKET, PIPE / CODE 61 FLANGE HEAD
12W7HQ1 3/4 0.75 0.265 0.750 1.500 1.62 2.34 1.78 1.500 1.062 3.5
16W7HQ1 1 1.00 0.315 1.000 1.750 1.62 2.38 1.75 1.750 1.328 3.5 Assembly /
20W7HQ1 1 1/4 1.25 0.315 1.250 2.000 1.81 2.62 1.94 2.000 1.672 3.5 Installation
24W7HQ1 1 1/2 1.50 0.315 1.500 2.375 2.00 2.88 2.12 2.375 1.922 2.7
32W7HQ1 2 2.00 0.375 2.000 2.812 2.00 3.00 2.12 2.812 2.406 2.5
EXTENDED WELD SOCKET, PIPE / CODE 62 FLANGE HEAD
16W7HQ2 1 1.00 0.375 1.000 1.875 2.34 3.06 2.62 2.000 1.328 5.5
20W7HQ2 1 1/4 1.25 0.405 1.125 2.125 2.50 3.31 3.18 2.312 1.672 5.5 Reference
24W7HQ2 1 1/2 1.50 0.495 1.375 2.500 3.06 3.93 3.18 2.750 1.922 5.5 Section
32W7HQ2 2 2.00 0.495 1.875 3.125 3.18 4.06 2.43 3.250 2.406 5.0

GHQ / G5HQ
Threaded Port Flange Adapter
NPTF or SAE Port / Code 61 Flange Head

GHQ
STANDARD
PT Dynamic
TUBE PORT FLANGE Pressure
FITTING THREAD SIZE C D F H L R (x 1,000 PSI)
PART # NPTF (in.) (in.) (in.) (in.) (in.) (in.) (in.) SX SS
NPTF PORT / CODE 61 FLANGE HEAD
12GHQ1 3/4-14 0.75 0.265 0.75 1.500 1.62 2.47 1.50 4.0
16GHQ1 1-11 1/2 1.00 0.315 1.00 1.750 1.62 2.66 1.75 4.0
20GHQ1 1 1/4-11 1/2 1.25 0.315 1.25 2.000 1.81 2.84 2.00 3.0
24GHQ1 1 1/2-11 1/2 1.50 0.315 1.50 2.375 2.00 3.00 2.38 2.0
32GHQ1 2-11 1/2 2.00 0.375 2.00 2.812 2.00 3.00 2.81 2.0

G5HQ
STANDARD
T5 SAE Dynamic
TUBE PORT PORT FLANGE Pressure
FITTING THREAD DASH SIZE C D F H L R (x 1,000 PSI)
PART # UN-2B SIZE (in.) (in.) (in.) (in.) (in.) (in.) (in.) SX SS
SAE PORT / CODE 61 FLANGE HEAD
12G5HQ1 1 1/6-12 12 0.75 0.265 0.75 1.500 1.62 2.47 1.50 4.0
16G5HQ1 1 5/16-12 15 1.00 0.315 1.00 1.750 1.62 2.66 1.75 3.0
20G5HQ1 1 5/8-12 20 1.25 0.315 1.25 2.000 1.81 2.84 2.00 2.2
24G5HQ1 1 7/8-12 24 1.50 0.315 1.50 2.375 2.00 3.00 2.38 2.5
32G5HQ1 2 1/2-12 32 2.00 0.375 2.00 2.812 2.00 3.00 2.81 1.2

Dimensions and pressures for reference only, subject to change.

M14 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

WB1HQ1 / WB3HQ1 / WB5HQ1

Code 61 Weld Butt Flange
Connector, Pipe
Schedule 40, 80 or 160 Weld Butt / How To
Code 61 Flange Head Order

O-ring Face Flat Face

STANDARD Specs
WELD BUTT Dynamic
FLANGE TUBE FITTING PIPE FLANGE Pressure
CONNECTION PART # SIZE SIZE C D F L W (x 1,000 PSI)
TYPE O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) SX SS Assembly /
SCHEDULE 40 WELD BUTT / CODE 61 FLANGE HEAD Installation
8WB1HQ1 8WB1HQ1N 1/2 0.50 0.265 0.622 1.188 1.06 0.840 5.3
12WB1HQ1 12WB1HQ1N 3/4 0.75 0.265 0.824 1.500 1.06 1.050 4.6
WB1HQ1 16WB1HQ1 16WB1HQ1N 1 1.00 0.315 1.049 1.750 1.25 1.315 4.0
For 20WB1HQ1 20WB1HQ1N 1 1/4 1.25 0.315 1.380 2.000 1.44 1.660 3.6 Reference
Schedule 40 24WB1HQ1 24WB1HQ1N 1 1/2 1.50 0.315 1.610 2.375 1.75 1.900 3.0 Section
pipe 32WB1HQ1 32WB1HQ1N 2 2.00 0.375 2.067 2.812 2.00 2.375 2.6
40WB1HQ1 40WB1HQ1N 2 1/2 2.50 0.375 2.469 3.312 2.31 2.875 2.6
48WB1HQ1 48WB1HQ1N 3 3.00 0.375 3.068 4.000 2.32 3.500 2.3
SCHEDULE 80 WELD BUTT / CODE 61 FLANGE HEAD
8WB3HQ1 8WB3HQ1N 1/2 0.50 0.265 0.546 1.188 1.06 0.840 5.0
12WB3HQ1 12WB3HQ1N 3/4 0.75 0.265 0.742 1.500 1.06 1.050 3.5
WB3HQ1 16WB3HQ1 16WB3HQ1N 1 1.00 0.315 0.957 1.750 1.25 1.315 4.0
For 20WB3HQ1 20WB3HQ1N 1 1/4 1.25 0.315 1.278 2.000 1.44 1.660 3.5
Schedule 80 24WB3HQ1 24WB3HQ1N 1 1/2 1.50 0.315 1.500 2.375 1.75 1.900 3.0
pipe 32WB3HQ1 32WB3HQ1N 2 2.00 0.375 1.939 2.812 2.00 2.375 3.0
40WB3HQ1 40WB3HQ1N 2 1/2 2.50 0.375 2.323 3.312 2.31 2.875 2.7
48WB3HQ1 48WB3HQ1N 3 3.00 0.375 2.900 4.000 2.32 3.500 2.2
SCHEDULE 160 WELD BUTT / CODE 61 FLANGE HEAD
8WB5HQ1 8WB5HQ1N 1/2 0.50 0.265 0.464 1.188 1.06 0.840 5.0
12WB5HQ1 12WB5HQ1N 3/4 0.75 0.265 0.614 1.500 1.06 1.050 4.0
WB5HQ1 16WB5HQ1 16WB5HQ1N 1 1.00 0.315 0.815 1.750 1.25 1.315 4.5
For 20WB5HQ1 20WB5HQ1N 1 1/4 1.25 0.315 1.160 2.000 1.44 1.660 4.0
Schedule 160 24WB5HQ1 24WB5HQ1N 1 1/2 1.50 0.315 1.337 2.375 1.75 1.900 3.0
pipe 32WB5HQ1 32WB5HQ1N 2 2.00 0.375 1.689 2.812 2.00 2.375 3.0
40WB5HQ1 40WB5HQ1N 2 1/2 2.50 0.375 2.125 3.312 2.31 2.875 2.5
48WB5HQ1 48WB5HQ1N 3 3.00 0.375 2.624 4.000 2.32 3.500 2.0

WB3HQ2 / WB5HQ2 / WB7HQ2

Code 62 Weld Butt Flange STANDARD
Connector, Pipe WELD BUTT Dynamic
TUBE FITTING Pressure
Schedule 80, 160 or FLANGE
PART #
PIPE FLANGE
(x 1,000 PSI)
CONNECTION SIZE SIZE C D F L W
XXS Weld Butt / Code 62 TYPE O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) SX SS
Flange Head SCHEDULE 80 WELD BUTT / CODE 62 FLANGE HEAD
12WB3HQ2 12WB3HQ2N 3/4 0.75 0.345 0.742 1.625 1.42 1.050 5.0
WB3HQ2 16WB3HQ2 16WB3HQ2N 1 1.00 0.375 0.957 1.875 1.61 1.315 4.5
For
20WB3HQ2 20WB3HQ2N 1 1/4 1.25 0.405 1.278 2.125 1.73 1.660 3.5
Schedule 80
24WB3HQ2 24WB3HQ2N 1 1/2 1.50 0.495 1.500 2.500 2.17 1.900 3.0
pipe
32WB3HQ2 32WB3HQ2N 2 2.00 0.495 1.939 3.125 2.48 2.375 3.0
SCHEDULE 160 WELD BUTT / CODE 62 FLANGE HEAD
12WB5HQ2 12WB5HQ2N 3/4 0.75 0.345 0.614 1.625 1.42 1.050 6.0
WB5HQ2 16WB5HQ2 16WB5HQ2N 1 1.00 0.375 0.815 1.875 1.61 1.315 5.5
For
20WB5HQ2 20WB5HQ2N 1 1/4 1.25 0.405 1.160 2.125 1.73 1.660 5.0
Schedule 160
24WB5HQ2 24WB5HQ2N 1 1/2 1.50 0.495 1.337 2.500 2.17 1.900 5.0
pipe
32WB5HQ2 32WB5HQ2N 2 2.00 0.495 1.689 3.125 2.48 2.375 4.5
SCHEDULE XXS WELD BUTT / CODE 62 FLANGE HEAD
12WB7HQ2 12WB7HQ2N 3/4 0.75 0.345 0.434 1.625 1.42 1.050 6.0
WB7HQ2 16WB7HQ2 16WB7HQ2N 1 1.00 0.375 0.599 1.875 1.61 1.315 6.0
For
20WB7HQ2 20WB7HQ2N 1 1/4 1.25 0.405 0.896 2.125 1.73 1.660 6.0
Schedule XXS
pipe 24WB7HQ2 24WB7HQ2N 1 1/2 1.50 0.495 1.100 2.500 2.17 1.900 6.0
32WB7HQ2 32WB7HQ2N 2 2.00 0.495 1.503 3.125 2.48 2.375 6.0

Dimensions and pressures for reference only, subject to change.

M15 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

G5Q
SAE Port Block Adapter
SAE Port / Code 61 or 62 Block Flange or Pad
How To
Order

O-ring Face Flat Face

Specs
STANDARD
SAE T5 K Dynamic
TUBE FITTING PORT STRAIGHT FLANGE DRILL T MOUNTING Pressure
PART # DASH THREAD SIZE A B D F I DIA. L THREAD HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE SIZE UN-2B (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B -SHCS SX SS1 Assembly /
SAE PORT / CODE 61 BLOCK FLANGE OR PAD Installation
8G5Q1B 8G5Q1P 8 3/4-16 0.50 1.81 2.13 0.50 0.63 1.25 0.344 1.42 5/16-18 5/16-18 x 1.25 5.0
12G5Q1B 12G5Q1P 12 1 1/16-12 0.75 1.97 2.56 0.75 0.71 1.54 0.406 1.42 3/8-16 3/8-16 x 1.50 4.0
16G5Q1B 16G5Q1P 16 1 5/16-12 1.00 2.17 2.75 1.00 0.71 1.81 0.406 1.50 3/8-16 3/8-16 x 1.50 3.5
20G5Q1B 20G5Q1P 20 1 5/8-12 1.25 2.68 3.12 1.25 0.83 2.22 0.469 1.61 7/16-14 7/16-14 x 1.75 3.0 Reference
24G5Q1B 24G5Q1P 24 1 7/8-12 1.50 3.07 3.66 1.50 0.98 2.50 0.531 1.77 1/2-13 1/2-13 x 1.75 2.5 Section
SAE PORT / CODE 62 BLOCK FLANGE OR PAD
8G5Q2B 8G5Q2P 8 3/4-16 0.50 1.81 2.21 0.50 0.63 1.33 0.344 1.42 5/16-18 5/16-18 x 1.25 6.0
12G5Q2B 12G5Q2P 12 1 1/16-12 0.75 2.17 2.80 0.75 0.83 1.65 0.406 1.38 3/8-16 3/8-16 x 1.50 5.5
16G5Q2B 16G5Q2P 16 1 5/16-12 1.00 2.56 3.19 1.00 0.98 1.98 0.409 1.65 7/16-14 7/16-14 x 1.75 4.5
20G5Q2B 20G5Q2P 20 1 5/8-12 1.25 3.07 3.75 1.25 1.06 2.36 0.531 1.77 1/2-13 1/2-13 x 1.75 3.0
24G5Q2B 24G5Q2P 24 1 7/8-12 1.50 3.70 4.41 1.50 1.18 2.68 0.656 1.97 5/8-11 5/8-11 x 2.25 2.7
32G5Q2B 32G5Q2P 32 2 1/2-12 2.00 4.50 5.28 2.00 1.46 3.38 0.781 2.56 3/4-10 3/4-10 x 2.75 2.0

1) See page M36 for standard stainless steel sizes and dimensions.
To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for
O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

GQ
NPTF Port Block Adapter
NPTF Port / Code 61 or 62 Block Flange or Pad

O-ring Face Flat Face

STANDARD
PT K Dynamic
TUBE FITTING PORT FLANGE DRILL T MOUNTING Pressure
PART # THREAD SIZE A B D F I DIA. L THREAD HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE NPTF (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS1
NPTF PORT / CODE 61 BLOCK FLANGE OR PAD
8GQ1B 8GQ1P 1/2 - 14 0.50 1.81 2.13 0.50 0.63 1.25 0.344 1.42 5/16-18 5/16-18 x 1.25 5.0
12GQ1B 12GQ1P 3/4 -14 0.75 1.97 2.56 0.75 0.71 1.54 0.406 1.42 3/8-16 3/8-16 x 1.50 4.5
16GQ1B 16GQ1P 1 - 11 1/2 1.00 2.17 2.75 1.00 0.71 1.81 0.406 1.50 3/8-16 3/8-16 x 1.50 4.0
20GQ1B 20GQ1P 1 1/4 - 11 1/2 1.25 2.68 3.12 1.25 0.83 2.22 0.469 1.61 7/16-14 7/16-14 x 1.75 3.5
24GQ1B 24GQ1P 1 1/2 - 11 1/2 1.50 3.07 3.66 1.50 0.98 2.50 0.531 1.77 1/2-13 1/2-13 x 1.75 2.7
32GQ1B 32GQ1P 2 - 11 1/2 2.00 3.54 4.00 2.00 0.98 3.12 0.531 1.77 1/2-13 1/2-13 x 1.75 2.2
40GQ1B 40GQ1P 2 1/2 - 8 2.50 4.09 4.49 2.50 0.98 3.62 0.531 1.97 1/2-13 1/2-13 x 1.75 2.0
48GQ1B 48GQ1P 3 1/2 - 8 3.00 4.88 5.28 3.00 1.06 4.47 0.656 1.97 5/8-11 5/8-11 x 2.00 1.1
NPTF PORT / CODE 62 BLOCK FLANGE OR PAD
8GQ2B 8GQ2P 1/2 - 14 0.50 1.81 2.21 0.50 0.63 1.33 0.344 1.42 5/16-18 5/16-18 x 1.25 6.0
12GQ2B 12GQ2P 3/4 - 14 0.75 2.17 2.80 0.75 0.83 1.65 0.406 1.38 3/8-16 3/8-16 x 1.50 5.0
16GQ2B 16GQ2P 1 - 11 1/2 1.00 2.56 3.19 1.00 0.98 1.98 0.469 1.65 7/16-14 7/16-14 x 1.75 4.0
20GQ2B 20Q2P 1 1/4 - 11 1/2 1.25 3.07 3.75 1.25 1.06 2.36 0.531 1.77 1/2-13 1/2-13 x 1.75 3.5
24GQ2B 24GQ2P 1 1/2 - 11 1/2 1.50 3.70 4.41 1.50 1.18 2.68 0.656 1.97 5/8-11 5/8-11 x 2.25 3.0
32GQ2B 32GQ2P 2 - 11 1/2 2.00 4.50 5.28 2.00 1.46 3.38 0.781 2.56 3/4-10 3/4-10 x 2.75 2.5

1) See page M36 for standard stainless steel sizes and dimensions.
To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available
for O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M16 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

G4Q
BSPP Port Block Adapter
BSPP Port / Code 61 or 62
Block Flange or Pad How To
Order

O-ring Face Flat Face

Specs
STANDARD
K Dynamic
TUBE FITTING T4 FLANGE DRILL T MOUNTING Pressure
PART # THREAD SIZE A B D F DIA. L M THREAD HARDWARE (x 1,000 PSI) Assembly /
O-RING FACE FLAT FACE BSPP (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS Installation
BSPP PORT / CODE 61 BLOCK FLANGE OR PAD
8G4Q1B 8G4Q1P 1/2-14 0.50 1.81 2.13 0.500 0.63 0.344 1.42 1.25 5/16-18 5/16-18 x 1.25 5.0
12G4Q1B 12G4Q1P 3/4-14 0.75 1.97 2.56 0.750 0.71 0.406 1.42 1.54 3/8-16 3/8-16 x 1.50 4.0
16G4Q1B 16G4Q1P 1-11 1.00 2.17 2.75 1.000 0.71 0.406 1.50 1.81 3/8-16 3/8-16 x 1.50 3.0 Reference
20G4Q1B 20G4Q1P 1 1/4-11 1.25 2.68 3.12 1.250 0.83 0.469 1.61 2.22 7/16-14 7/16-14 x 1.75 2.5 Section
24G4Q1B 24G4Q1P 1 1/2-11 1.50 3.07 3.66 1.500 0.98 0.531 1.77 2.50 1/2-13 1/2-13 x 1.75 2.2
32G4Q1B 32G4Q1P 2-11 2.00 3.54 4.00 2.000 0.98 0.531 1.77 3.12 1/2-13 1/2-13 x 1.75 1.7
BSPP PORT / CODE 62 BLOCK FLANGE OR PAD
8G4Q2B 8G4Q2P 1/2-14 0.50 1.81 2.21 0.500 0.63 0.344 1.42 1.33 5/16-18 5/16-18 x 1.25 6.0
12G4Q2B 12G4Q2P 3/4-14 0.75 2.17 2.80 0.750 0.83 0.406 1.38 1.65 3/8-16 3/8-16 x 1.50 5.0
16G4Q2B 16G4Q2P 1-11 1.00 2.56 3.19 1.000 0.98 0.469 1.65 1.98 7/16-14 7/16-14 x 1.75 4.0
20G4Q2B 20G4Q2P 1 1/4-11 1.25 3.07 3.75 1.250 1.06 0.531 1.77 2.36 1/2-13 1/2-13 x 1.75 3.0
24G4Q2B 24G4Q2P 1 1/2-11 1.50 3.70 4.41 1.500 1.18 0.656 1.97 2.68 5/8-11 5/8-11 x 2.25 2.5
32G4Q2B 32G4Q2P 2-11 2.00 4.50 5.28 2.000 1.46 0.781 2.56 3.35 3/4-10 3/4-10 x 2.75 2.0

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are avail-
able for O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M17 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

W5Q
Flat Weld Socket Block Connector, Pipe
Flat Weld Socket, Pipe / Code 61 or 62
Block Flange or Pad How To
Order

O-ring Face Flat Face

STANDARD Specs
K Dynamic
TUBE FITTING PIPE FLANGE DRILL T MOUNTING Pressure
PART # SIZE SIZE A B D J DIA. L S THREAD HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS1
FLAT WELD SOCKET, PIPE / CODE 61 BLOCK FLANGE OR PAD Assembly /
8W5Q1B 8W5Q1P 1/2 0.50 1.813 2.125 0.500 0.560 0.344 0.750 0.855 5/16-18 5/16-18 x 1.50 5.0 Installation
12W5Q1B 12W5Q1P 3/4 0.75 2.063 2.563 0.750 0.560 0.406 0.750 1.062 3/8-16 3/8-16 x 1.50 5.0
16W5Q1B 16W5Q1P 1 1.00 2.313 2.750 1.000 0.630 0.406 0.880 1.326 3/8-16 3/8-16 x 1.75 5.0
20W5Q1B 20W5Q1P 1 1/4 1.25 2.875 3.125 1.250 0.690 0.469 0.940 1.672 7/16-14 7/16-14 x 1.75 4.0
24W5Q1B 24W5Q1P 1 1/2 1.50 3.250 3.688 1.500 0.750 0.531 1.190 1.922 1/2-13 1/2-13 x 2.25 3.0 Reference
32W5Q1B 32W5Q1P 2 2.00 3.813 4.000 2.000 0.875 0.531 1.380 2.406 1/2-13 1/2-13 x 2.50 3.0 Section
40W5Q1B 40W5Q1P 2 1/2 2.50 4.281 4.500 2.500 1.000 0.531 1.750 2.906 1/2-13 1/2-13 x 2.75 2.5
48W5Q1B 48W5Q1P 3 3.00 5.156 5.313 3.000 1.250 0.656 2.120 3.547 5/8-11 5/8-11 x 3.50 2.0
56W5Q1B 56W5Q1P 3 1/2 3.50 5.500 6.000 3.500 1.190 0.656 1.440 4.047 5/8-11 5/8-11 x 2.75 0.5
64W5Q1B 64W5Q1P 4 4.00 6.000 6.380 4.000 1.250 0.656 1.500 4.578 5/8-11 5/8-11 x 2.75 0.5
80W5Q1B 80W5Q1P 5 5.00 7.120 7.250 4.500 1.380 0.656 1.750 5.641 5/8-11 5/8-11 x 3.00 0.5
FLAT WELD SOCKET, PIPE / CODE 62 BLOCK FLANGE OR PAD
8W5Q2B 8W5Q2P 1/2 0.50 1.940 2.300 0.500 0.560 0.344 1.250 0.855 5/16-18 5/16-18 x 2.00 6.0
12W5Q2B 12W5Q2P 3/4 0.75 2.500 2.950 0.750 0.560 0.406 1.250 1.062 3/8-16 3/8-16 x 2.00 6.0
16W5Q2B 16W5Q2P 1 1.00 2.750 3.190 1.000 0.630 0.469 1.500 1.326 7/16-14 7/16-14 x 2.50 6.0
20W5Q2B 20W5Q2P 1 1/4 1.25 3.060 3.750 1.250 0.690 0.531 1.500 1.672 1/2-13 1/2-13 x 2.50 6.0
24W5Q2B 24W5Q2P 1 1/2 1.50 3.750 4.440 1.500 0.750 0.656 1.750 1.922 5/8-11 5/8-11 x 3.00 6.0
32W5Q2B 32W5Q2P 2 2.00 4.500 5.250 2.000 0.875 0.781 1.750 2.406 3/4-10 3/4-10 x 3.00 6.0
40W5Q2B2 40W5Q2P2 2 1/2 2.50 5.870 6.870 2.500 1.000 0.906 2.060 2.906 7/8-9 7/8-9 x 3.50 6.0
48W5Q2B2 48W5Q2P2 3 3.00 7.000 8.500 3.000 1.250 1.156 2.620 3.547 1 1/8-7 1 1/8-7 x 4.50 6.0

1) See page M37 for standard stainless steel sizes and dimensions.
2) Not covered in SAE J518. Bolt hole centerline dimensions are: 2.312” x 4.875” for 40W5Q2 and 2.812” x 6.000” for 48W5Q2.
To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for
O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M18 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

W4Q
Flat Weld Socket Block Connector, Tube
Flat Weld Socket, Tube / Code 61 or 62
Block Flange or Pad How To
Order

O-ring Face Flat Face

Specs
STANDARD
K Dynamic
TUBE FITTING TUBE FLANGE DRILL T MOUNTING Pressure
PART # O.D. SIZE A B D J DIA. L S THREAD HARDWARE (x 1,000 PSI) Assembly /
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS Installation
FLAT WELD SOCKET, TUBE / CODE 61 BLOCK FLANGE OR PAD
12W4Q1B 12W4Q1P 3/4 0.75 2.06 2.56 0.625 0.560 0.406 0.750 0.752 3/8-16 3/8-16 x 1.50 5.0
16-12W4Q1B 16-12W4Q1P 1 0.75 2.06 2.56 0.750 0.560 0.406 0.750 1.002 3/8-16 3/8-16 x 1.50 5.0
16W4Q1B 16W4Q1P 1 1.00 2.31 2.75 0.875 0.630 0.406 0.880 1.002 3/8-16 3/8-16 x 1.75 5.0
Reference
20-16W4Q1B 20-16W4Q1P 1 1/4 1.00 2.31 2.75 1.000 0.630 0.406 0.880 1.252 3/8-16 3/8-16 x 1.75 5.0
Section
20W4Q1B 20W4Q1P 1 1/4 1.25 2.88 3.12 1.125 0.690 0.469 0.940 1.252 7/16-14 7/16-14 x 1.75 4.0
24-20W4Q1B 24-20W4Q1P 1 1/2 1.25 2.88 3.12 1.250 0.690 0.469 0.940 1.502 7/16-14 7/16-14 x 1.75 4.0
24W4Q1B 24W4Q1P 1 1/2 1.50 3.25 3.69 1.375 0.750 0.531 1.190 1.502 1/2-13 1/2-13 x 2.25 3.0
28-24W4Q1B 28-24W4Q1P 1 3/4 1.50 3.25 3.69 1.500 0.750 0.531 1.190 1.752 1/2-13 1/2-13 x 2.25 3.0
32W4Q1B 32W4Q1P 2 2.00 3.81 4.00 1.875 0.875 0.531 1.375 2.002 1/2-13 1/2-13 x 2.50 3.0
36-32W4Q1B 36-32W4Q1P 2 1/4 2.00 3.81 4.00 2.000 0.875 0.531 1.375 2.252 1/2-13 1/2-13 x 2.50 3.0
FLAT WELD SOCKET, TUBE / CODE 62 BLOCK FLANGE OR PAD
12W4Q2B 12W4Q2P 3/4 0.75 2.38 2.81 0.625 0.560 0.406 1.250 0.752 3/8-16 3/8-16 x 2.00 6.0
16-12W4Q2B 16-12W4Q2P 1 0.75 2.38 2.81 0.750 0.560 0.406 1.250 1.002 3/8-16 3/8-16 x 2.00 6.0
16W4Q2B 16W4Q2P 1 1.00 2.75 3.19 0.875 0.630 0.469 1.500 1.002 7/16-14 7/16-14 x 2.25 6.0
20-16W4Q2B 20-16W4Q2P 1 1/4 1.00 2.75 3.19 1.000 0.630 0.469 1.500 1.252 7/16-14 7/16-14 x 2.25 6.0
20W4Q2B 20W4Q2P 1 1/4 1.25 3.06 3.75 1.125 0.690 0.531 1.500 1.252 1/2-13 1/2-13 x 2.50 6.0
24-20W4Q2B 24-20W4Q2P 1 1/5 1.25 3.06 3.75 1.250 0.690 0.531 1.500 1.502 1/2-13 1/2-13 x 2.50 6.0
24W4Q2B 24W4Q2P 1 1/2 1.50 3.75 4.44 1.375 0.750 0.656 1.750 1.502 5/8-11 5/8-11 x 2.75 6.0
28-24W4Q2B 28-24W4Q2P 1 3/4 1.50 3.75 4.44 1.500 0.750 0.656 1.750 1.752 5/8-11 5/8-11 x 2.75 6.0
32W4Q2B11 32W4Q2P11 2 2.00 4.50 5.25 1.875 0.875 0.781 1.750 2.002 3/4-10 3/4-10 x 3.00 6.0
36-32W4Q2B11 36-32W4Q2P11 2 1/4 2.00 4.50 5.25 2.000 0.875 0.781 1.750 2.252 3/4-10 3/4-10 x 3.00 6.0

1) Not covered in SAE J518.

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for
O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M19 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

W7Q
Extended Weld Socket Block Connector, Pipe
Deep Weld Socket, Pipe / Code 61 or 62
Block Flange or Pad How To
Order

O-ring Face Flat Face

Specs
STANDARD
K Dynamic
TUBE FITTING PIPE FLANGE DRILL T MOUNTING Pressure
PART # SIZE SIZE A B D E I J DIA. L S THREAD HARDWARE (x 1,000 PSI) Assembly /
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS Installation
EXTENDED WELD SOCKET, PIPE / CODE 61 BLOCK FLANGE OR PAD
12W7Q1B 12W7Q1P 3/4 0.75 1.97 2.56 0.75 0.710 1.54 0.750 0.406 1.420 1.062 3/8-16 3/8-16 x 1.50 5.0
16W7Q1B 16W7Q1P 1 1.00 2.17 2.75 1.00 0.710 1.81 0.750 0.406 1.500 1.328 3/8-16 3/8-16 x 1.50 4.5
20W7Q1B 20W7Q1P 1 1/4 1.25 2.68 3.12 1.25 0.830 2.22 0.870 0.469 1.610 1.672 7/16-14 7/16-14 x 1.75 2.7 Reference
Section
24W7Q1B 24W7Q1P 1 1/2 1.50 3.07 3.66 1.50 0.980 2.50 0.940 0.531 1.770 1.922 1/2-13 1/2-13 x 1.75 3.0
32W7Q1B 32W7Q1P 2 2.00 3.54 4.00 2.00 0.980 3.12 1.020 0.531 1.770 2.406 1/2-13 1/2-13 x 1.75 2.5
40W7Q1B 40W7Q1P 2 1/2 2.50 4.09 4.49 2.50 0.980 3.62 1.180 0.531 1.970 2.906 1/2-13 1/2-13 x 1.75 2.2
EXTENDED WELD SOCKET, PIPE / C ODE 62 BLOCK FLANGE OR PAD
12W7Q2B 12W7Q2P 3/4 0.75 2.17 2.80 0.75 0.830 1.65 0.870 0.406 1.380 1.062 3/8-16 3/8-16 x 1.50 6.0
16W7Q2B 16W7Q2P 1 1.00 2.56 3.19 1.00 0.980 1.98 0.870 0.469 1.650 1.328 7/16-14 7/16-14 x 1.75 6.0
20W7Q2B 20W7Q2P 1 1/4 1.25 3.07 3.75 1.25 1.060 2.36 0.980 0.531 1.770 1.672 1/2-13 1/2-13 x 1.75 5.5
24W7Q2B 24W7Q2P 1 1/2 1.50 3.7 4.41 1.50 1.180 2.68 1.100 0.656 1.970 1.922 5/8-11 5/8-11 x 2.25 5.5
32W7Q2B 32W7Q2P 2 2.00 4.5 5.28 2.00 1.460 3.35 0.940 0.781 2.560 2.406 3/4-10 3/4-10 x 2.75 5.0

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for
O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M20 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

W6Q
Extended Weld Socket Block Connector, Tube
Deep Weld Socket, Tube / Code 61 or 62
Block Flange or Pad How To
Order

O-ring Face Flat Face

Specs
STANDARD
K Dynamic
TUBE FITTING TUBE FLANGE DRILL T MOUNTING Pressure
PART # O.D. SIZE A B D E I J DIA. L S THREAD HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS Assembly /
EXTENDED WELD SOCKET, TUBE / CODE 61 BLOCK FLANGE OR PAD Installation
12W6Q1B 12W6Q1P 3/4 0.75 1.97 2.56 0.625 0.71 1.54 0.560 0.406 1.420 0.752 3/8-16 3/8-16 x 1.50 5.0
16-12W6Q1B 16-12W6Q1P 1 0.75 1.97 2.56 0.750 0.71 1.54 0.560 0.406 1.420 1.002 3/8-16 3/8-16 x 1.50 5.0
16W6Q1B 16W6Q1P 1 1.00 2.17 2.75 0.875 0.71 1.81 0.630 0.406 1.500 1.002 3/8-16 3/8-16 x 1.50 5.0
20-16W6Q1B 20-16W6Q1P 1 1/4 1.00 2.17 2.75 1.000 0.71 1.81 0.630 0.406 1.500 1.252 3/8-16 3/8-16 x 1.50 5.0 Reference
20W6Q1B 20W6Q1P 1 1/4 1.25 2.68 3.12 1.125 0.83 2.22 0.690 0.469 1.610 1.252 7/16-14 7/16-14 x 1.75 4.0 Section
24-20W6Q1B 24-20W6Q1P 1 1/2 1.25 2.68 3.12 1.250 0.83 2.22 0.690 0.469 1.610 1.502 7/16-14 7/16-14 x 1.75 4.0
24W6Q1B 24W6Q1P 1 1/2 1.50 3.07 3.66 1.375 0.98 2.50 0.750 0.531 1.770 1.502 1/2-13 1/2-13 x 1.75 3.0
28-24W6Q1B 28-24W6Q1P 1 3/4 1.50 3.07 3.66 1.500 0.98 2.50 0.750 0.531 1.770 1.752 1/2-13 1/2-13 x 1.75 3.0
32W6Q1B 32W6Q1P 2 2.00 3.54 4.00 1.875 0.98 3.12 0.870 0.531 1.770 2.002 1/2-13 1/2-13 x 1.75 3.0
36-32W6Q1B 36-32W6Q1P 2 1/4 2.00 3.54 4.00 2.000 0.98 3.12 0.870 0.531 1.770 2.252 1/2-13 1/2-13 x 1.75 3.0
40W6Q1B 40W6Q1P 2 1/2 2.50 4.09 4.49 2.375 0.98 3.62 1.000 0.531 1.970 2.502 1/2-13 1/2-13 x 1.75 2.5
44-40W6Q1B 44-40W6Q1P 2 3/4 2.50 4.09 4.49 2.500 0.98 3.62 1.000 0.531 1.970 2.752 1/2-13 1/2-13 x 1.75 2.2
EXTENDED WELD SOCKET, TUBE / CODE 62 BLOCK FLANGE OR PAD
12W6Q2B 12W6Q2P 3/4 0.75 2.17 2.80 0.625 0.83 1.65 0.560 0.406 1.380 0.752 3/8-16 3/8-16 x 1.50 6.0
16-12W6Q2B 16-12W6Q2P 1 0.75 2.17 2.80 0.750 0.83 1.65 0.560 0.406 1.380 1.002 3/8-16 3/8-16 x 1.50 6.0
16W6Q2B 16W6Q2P 1 1.00 2.56 3.19 0.875 0.98 1.98 0.630 0.469 1.650 1.002 7/16-14 7/16-14 x 1.75 6.0
20-16W6Q2B 20-16W6Q2P 1 1/4 1.00 2.56 3.19 1.000 0.98 1.98 0.630 0.469 1.650 1.252 7/16-14 7/16-14 x 1.75 6.0
20W6Q2B 20W6Q2P 1 1/4 1.25 3.07 3.75 1.125 1.06 2.36 0.690 0.531 1.770 1.252 1/2-13 1/2-13 x 1.75 6.0
24-20W6Q2B 24-20W6Q2P 1 1/2 1.25 3.07 3.75 1.250 1.06 2.36 0.690 0.531 1.770 1.502 1/2-13 1/2-13 x 1.75 6.0
24W6Q2B 24W6Q2P 1 1/2 1.50 3.70 4.41 1.375 1.18 2.68 0.750 0.656 1.970 1.502 5/8-11 5/8-11 x 2.25 6.0
28-24W6Q2B 28-24W6Q2P 1 3/4 1.50 3.70 4.41 1.500 1.18 2.68 0.750 0.656 1.970 1.752 5/8-11 5/8-11 x 2.25 6.0
32W6Q2B 32W6Q2P 2 2.00 4.50 5.28 1.875 1.46 3.35 0.870 0.781 2.560 2.002 3/4-10 3/4-10 x 2.75 6.0
36-32W6Q2B 36-32W6Q2P 2 1/4 2.00 4.50 5.28 2.000 1.46 3.35 0.870 0.781 2.560 2.252 3/4-10 3/4-10 x 2.75 5.5

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for
O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M21 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

WB1Q1 / WB3Q1 / WB5Q1

Code 61 Weld Butt Block Connector, Pipe
Schedule 40, 80 or 160 Weld Butt /
Code 61 Block Flange or Pad How To
Order

O-ring Face Flat Face

Specs
STANDARD
WELD BUTT D K W Dynamic
BLOCK TUBE FITTING PIPE FLANGE PIPE DRILL T PIPE MOUNTING Pressure
CONNECTION PART # SIZE SIZE A B I.D. E DIA. L THREAD O.D. HARDWARE (x 1,000 PSI)
TYPE O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B (in.) SHCS SX SS Assembly /
SCHEDULE 40 WELD BUTT / CODE 61 BLOCK FLANGE OR PAD Installation
12WB1Q1B 12WB1Q1P 3/4 0.75 1.97 2.56 0.826 0.710 0.406 1.420 3/8-16 1.050 3/8-16 x 1.50 3.5
16WB1Q1B 16WB1Q1P 1 1.00 2.17 2.75 1.051 0.710 0.406 1.500 3/8-16 1.315 3/8-16 x 1.50 3.0
WB1Q1 20WB1Q1B 20WB1Q1P 1 1/4 1.25 2.68 3.12 1.382 0.830 0.469 1.610 7/16-14 1.660 7/16-14 x 1.75 2.7
For
24WB1Q1B 24WB1Q1P 1 1/2 1.50 3.07 3.66 1.612 0.980 0.531 1.730 1/2-13 1.900 1/2-13 x 1.75 2.2 Reference
Schedule 40
pipe 32WB1Q1B 32WB1Q1P 2 2.00 3.54 4.00 2.069 0.980 0.531 1.770 1/2-13 2.375 1/2-13 x 1.75 2.0 Section
40WB1Q1B 40WB1Q1P 2 1/2 2.50 4.09 4.49 2.471 0.980 0.531 1.970 1/2-13 2.875 1/2-13 x 1.75 2.0
48WB1Q1B 48WB1Q1P 3 3.00 4.88 5.28 3.070 1.060 0.656 1.970 5/8-11 3.500 5/8-11 x 2.00 1.7
SCHEDULE 80 WELD BUTT / CODE 61 BLOCK FLANGE OR PAD
12WB3Q1B 12WB3Q1P 3/4 0.75 1.97 2.56 0.744 0.710 0.406 1.420 3/8-16 1.050 3/8-16 x 1.50 5.0
16WB3Q1B 16WB3Q1P 1 1.00 2.17 2.75 0.959 0.710 0.406 1.500 3/8-16 1.315 3/8-16 x 1.50 4.5
WB3Q1 20WB3Q1B 20WB3Q1P 1 1/4 1.25 2.68 3.12 1.280 0.830 0.469 1.610 7/16-14 1.660 7/16-14 x 1.75 4.0
For
24WB3Q1B 24WB3Q1P 1 1/2 1.50 3.07 3.66 1.502 0.980 0.531 1.730 1/2-13 1.900 1/2-13 x 1.75 3.0
Schedule 80
pipe 32WB3Q1B 32WB3Q1P 2 2.00 3.54 4.00 1.941 0.980 0.531 1.770 1/2-13 2.375 1/2-13 x 1.75 3.0
40WB3Q1B 40WB3Q1P 2 1/2 2.50 4.09 4.49 2.325 0.980 0.531 1.970 1/2-13 2.875 1/2-13 x 1.75 2.5
48WB3Q1B 48WB3Q1P 3 3.00 4.88 5.28 2.902 1.060 0.656 1.970 5/8-11 3.500 5/8-11 x 2.00 2.0
SCHEDULE 160 WELD BUTT / CODE 61 BLOCK FLANGE OR PAD
12WB5Q1B 12WB5Q1P 3/4 0.75 1.97 2.56 0.614 0.710 0.406 1.420 3/8-16 1.050 3/8-16 x 1.50 5.0
16WB5Q1B 16WB5Q1P 1 1.00 2.17 2.75 0.817 0.710 0.406 1.500 3/8-16 1.315 3/8-16 x 1.50 5.0
WB5Q1 20WB5Q1B 20WB5Q1P 1 1/4 1.25 2.68 3.12 1.162 0.830 0.469 1.610 7/16-14 1.660 7/16-14 x 1.75 4.0
For
24WB5Q1B 24WB5Q1P 1 1/2 1.50 3.07 3.66 1.340 0.980 0.531 1.730 1/2-13 1.900 1/2-13 x 1.75 3.0
Schedule 160
pipe 32WB5Q1B 32WB5Q1P 2 2.00 3.54 4.00 1.689 0.980 0.531 1.770 1/2-13 2.375 1/2-13 x 1.75 3.0
40WB5Q1B 40WB5Q1P 2 1/2 2.50 4.09 4.49 2.127 0.980 0.531 1.970 1/2-13 2.875 1/2-13 x 1.75 2.5
48WB5Q1B 48WB5Q1P 3 3.00 4.88 5.28 2.626 1.060 0.656 1.970 5/8-11 3.500 5/8-11 x 2.00 2.0

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for O-
ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M22 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

WB3Q2 / WB5Q2 / WB7Q2

Code 62 Weld Butt Block Connector, Pipe
Schedule 80, 160 or XXS Weld Butt /
Code 62 Block Flange or Pad How To
Order

O-ring Face Flat Face

STANDARD Specs
WELD BUTT D K W Dynamic
BLOCK TUBE FITTING PIPE FLANGE PIPE DRILL T PIPE MOUNTING Pressure
CONNECTION PART # SIZE SIZE A B I.D. E DIA. L THREAD O.D. HARDWARE (x 1,000 PSI)
TYPE O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B (in.) SHCS SX SS Assembly /
SCHEDULE 80 WELD BUTT / CODE 62 BLOCK FLANGE OR PAD Installation
12WB3Q2B 12WB3Q2P 3/4 0.75 2.17 2.80 0.744 0.83 0.406 1.38 3/8-16 1.050 3/8-16 x 1.50 5.0
WB3Q2 16WB3Q2B 16WB3Q2P 1 1.00 2.56 3.19 0.959 0.83 0.469 1.61 7/16-14 1.315 7/16-14 x 1.75 4.5
For
20WB3Q2B 20WB3Q2P 1 1/4 1.25 3.07 3.75 1.280 0.98 0.531 1.73 1/2-13 1.660 1/2-13 x 1.75 3.5
Schedule 80
pipe 24WB3Q2B 24WB3Q2P 1 1/2 1.50 3.70 4.41 1.502 1.18 0.656 2.17 5/8-11 1.900 5/8-11 x 2.25 3.0 Reference
32WB3Q2B 32WB3Q2P 2 2.00 4.50 5.28 1.941 1.46 0.781 2.56 3/4-10 2.375 3/4-10 x 2.75 3.0 Section
SCHEDULE 160 WELD BUTT / CODE 62 BLOCK FLANGE OR PAD
12WB5Q2B 12WB5Q2P 3/4 0.75 2.17 2.80 0.614 0.83 0.406 1.38 3/8-16 1.050 3/8-16 x 1.50 6.0
WB5Q2 16WB5Q2B 16WB5Q2P 1 1.00 2.56 3.19 0.817 0.83 0.469 1.61 7/16-14 1.315 7/16-14 x 1.75 6.0
For
20WB5Q2B 20WB5Q2P 1 1/4 1.25 3.07 3.75 1.162 0.98 0.531 1.73 1/2-13 1.660 1/2-13 x 1.75 5.0
Schedule 160
pipe 24WB5Q2B 24WB5Q2P 1 1/2 1.50 3.70 4.41 1.340 1.18 0.656 2.17 5/8-11 1.900 5/8-11 x 2.25 5.0
32WB5Q2B 32WB5Q2P 2 2.00 4.50 5.28 1.689 1.46 0.781 2.56 3/4-10 2.375 3/4-10 x 2.75 6.0
SCHEDULE XXS WELD BUTT / CODE 62 BLOCK FLANGE OR PAD
12WB7Q2B 12WB7Q2P 3/4 0.75 2.17 2.80 0.436 0.83 0.406 1.38 3/8-16 1.050 3/8-16 x 1.50 6.0
WB7Q2 16WB7Q2B 16WB7Q2P 1 1.00 2.56 3.19 0.601 0.83 0.469 1.61 7/16-14 1.315 7/16-14 x 1.75 6.0
For
20WB7Q2B 20WB7Q2P 1 1/4 1.25 3.07 3.75 0.898 0.98 0.531 1.73 1/2-13 1.660 1/2-13 x 1.75 6.0
Schedule XXS
pipe 24WB7Q2B 24WB7Q2P 1 1/2 1.50 3.70 4.41 1.102 1.18 0.656 2.17 5/8-11 1.900 5/8-11 x 2.25 6.0
32WB7Q2B 32WB7Q2P 2 2.00 4.50 5.28 1.505 1.46 0.781 2.56 3/4-10 2.375 3/4-10 x 2.75 6.0

1) SAE J518 does not cover these sizes in Code 62.

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for O-
ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M23 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

AS3 / AS6
SAE-Flange / Weld Butt

For metric tube welded connection

How To
Order
TUBE O.D.
TUBE x WALL WORKING WELD STANDARD
FITTING SIZE THICKNESS PRESSURE d1 d7 I I1 S6 NIPPLE FROM STOCK
PART # (in.) (mm) (bar) (mm) (mm) (mm) (mm) (mm) BODY A3C 71
Specs
SAE FLANGE CONNECTION – CODE 61 – STANDARD SERIES
AS32/15X2 1/2 15 x 2 200 11 23.9 11.5 38 6 AS32/15X2X
AS32/16X3 1/2 16 x 3 220 10 23.9 11.5 38 6 AS32/16X3X
AS33/18X1.5 3/4 18 x 1.5 130 15 31.8 15.5 50 8 AS33/18X1.5X
AS33/22X2 3/4 22 x 2 140 18 31.8 15.5 50 8 AS33/22X2X Assembly /
AS33/20X3 3/4 20 x 3 220 14 31.8 15.5 50 8 AS33/20X3X Installation
AS33/25X4 3/4 25 x 4 220 17 31.8 15.5 50 8 AS33/25X4X
AS34/28X2 1 28 x 2 115 24 38 13.5 50 8 AS34/28X2X
AS34/30X4.5 1 30 x 4.5 220 21 38 13.5 50 8 AS34/30X4.5X
AS35/35X2 1 1/4 35 x 2 90 31 43 18.5 55 8 AS35/35X2X
AS35/25X3 1 1/4 25 x 3 175 19 43 18.5 55 8 AS35/25X3X Reference
AS35/30X4 1 1/4 30 x 4 175 22 43 18.5 55 8 AS35/30X4X Section
AS35/38X5 1 1/4 38 x 5 175 28 43 18.5 55 8 AS35/38X5X
AS36/42X3 1 1/2 42 x 3 115 36 50 18.5 57 10 AS36/42X3X
AS36/38X4 1 1/2 38 x 4 130 30 50 18.5 57 10 AS36/38X4X
AS38/50X6 2 50 x 6 130 38 62 24 62 12 AS38/50X6X
AS38/65X8 2 65 x 8 130 49 65 24 62 12 AS38/65X8X
SAE FLANGE CONNECTION – CODE 62 – HIGH PRESSURE SERIES
AS62/16X3 1/2 16 x 3 260 10 23.9 13.5 41 6 AS62/16X3X
AS63/25X5 3/4 25 x 5 260 15 31.8 15.5 55 8 AS63/25X5X
AS64/25X5 1 25 x 5 260 15 38 20.5 67 10 AS64/25X5X
AS64/30X4 1 30 x 4 200 22 38 20.5 67 10 AS64/30X4X
AS65/30X4* 1 1/4 30 x 4 200 22 43.7 17.5 78 10 AS65/30X4X
AS65/38X5 1 1/4 38 x 5 200 28 43.7 17.5 78 10 AS65/38X5X
AS65/38X8* 1 1/4 38 x 8 260 22 43.7 17.5 78 10 AS65/38X8X
AS66/38X5 1 1/2 38 x 5 200 28 50.8 24.5 85 14 AS66/38X5X
AS66/38X8 1 1/2 38 x 8 260 22 50.8 24.5 85 14 AS66/38X8X
AS68/50X9 2 50 x 9 260 32 66.6 32.5 116 17 AS68/50X9X
AS68/65X9 2 65 x 8 190 49 66.6 32.5 116 17 AS68/65X8X

* Identical types.
Temperature range without pressure reductions for fittings with O-ring sealing of NBR
(e.g., buna N series) -35°C up to +100°C, FPM (e.g., fluorocarbon on request) -25°C up to +120°C.
Tightening torques for socket head cap screws see Tables T6 and T7.

WBT
Code 61 Weld Butt Tank Adapter
Weld Butt with Pilot / Code 61 Block Flange Pad

STANDARD
Dynamic
TUBE FLANGE T Pressure
FITTING SIZE A B D E L P THREAD W (x 1,000 PSI)
PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B (in.) S SS
12WBTQ1P 0.75 1.97 2.56 0.75 0.71 1.42 1.30 3/8-16 1.375 0.5
16WBTQ1P 1.00 2.17 2.75 1.00 0.71 1.50 1.37 3/8-16 1.500 0.5
20WBTQ1P 1.25 2.68 3.12 1.25 0.83 1.61 1.49 7/16-14 1.750 0.5
24WBTQ1P 1.50 3.07 3.66 1.50 0.98 1.77 1.64 1/2-13 2.125 0.5
32WBTQ1P 2.00 3.54 4.00 2.00 0.98 1.77 1.65 1/2-13 2.500 0.5
40WBTQ1P 2.50 4.09 4.50 2.50 0.98 1.97 1.85 1/2-13 3.250 0.5

Dimensions and pressures for reference only, subject to change.

M24 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

WSD
Code 61 Weld Saddle Block Connector
Pipe or Tube Weld Saddle /
Code 61 Block Flange or Pad How To
Order

O-ring Face Flat Face Specs

STANDARD
PIPE OR K Dynamic
TUBE FITTING TUBE FLANGE DRILL T MOUNTING Pressure
PART # SIZE SIZE A B D E DIA. L S THREAD HARDWARE (x 1,000 PSI) Assembly /
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS Installation
PIPE WELD SADDLE / CODE 61 BLOCK FLANGE OR PAD
12WSD1Q1B 12WSD1Q1P 3/4 0.75 1.97 2.56 0.75 0.710 0.406 1.42 0.532 3/8-16 3/8-16 x 1.50 5.0
16WSD1Q1B 16WSD1Q1P 1 1.00 2.17 2.75 1.00 0.710 0.406 1.50 0.665 3/8-16 3/8-16 x 1.50 5.0
20WSD1Q1B 20WSD1Q1P 1 1/4 1.25 2.68 3.12 1.25 0.830 0.469 1.61 0.837 7/16-14 7/16-14 x 1.75 4.0 Reference
24WSD1Q1B 24WSD1Q1P 1 1/2 1.50 3.07 3.66 1.50 0.980 0.531 1.77 0.957 1/2-13 1/2-13 x 1.75 3.0 Section
32WSD1Q1B 32WSD1Q1P 2 2.00 3.54 4.00 2.00 0.980 0.531 1.77 1.200 1/2-13 1/2-13 x 1.75 3.0
TUBE WELD SADDLE / CODE 61 BLOCK FLANGE OR PAD
12WSD2Q1B 12WSD2Q1P 3/4 0.75 1.97 2.56 0.75 0.710 0.406 1.42 0.382 3/8-16 3/8-16 x 1.50 5.0
16-12WSD2Q1B 16-12WSD2Q1P 1 0.75 1.97 2.56 0.75 0.710 0.406 1.42 0.507 3/8-16 3/8-16 x 1.50 5.0
16WSD2Q1B 16WSD2Q1P 1 1.00 2.17 2.75 1.00 0.710 0.406 1.50 0.507 3/8-16 3/8-16 x 1.50 5.0
20-16WSD2Q1B 20-16WSD2Q1P 1 1/4 1.00 2.17 2.75 1.00 0.710 0.406 1.50 0.632 3/8-16 3/8-16 x 1.50 5.0
20WSD2Q1B 20WSD2Q1P 1 1/4 1.25 2.68 3.12 1.25 0.830 0.469 1.61 0.632 7/16-14 7/16-14 x 1.75 4.0
24-20WSD2Q1B 24-20WSD2Q1P 1 1/2 1.25 2.68 3.12 1.25 0.830 0.469 1.61 0.757 7/16-14 7/16-14 x 1.75 4.0
24WSD2Q1B 24WSD2Q1P 1 1/2 1.50 3.07 3.66 1.50 0.980 0.531 1.77 0.757 1/2-13 1/2-13 x 1.75 3.0
28-24WSD2Q1B 28-24WSD2Q1P 1 3/4 1.50 3.07 3.66 1.50 0.980 0.531 1.77 0.882 1/2-13 1/2-13 x 1.75 3.0
32WSD2Q1B 32WSD2Q1P 2 2.00 3.54 4.00 2.00 0.980 0.531 1.77 1.007 1/2-13 1/2-13 x 1.75 3.0
36-32WSD2Q1B 36-32WSD2Q1P 2 1/4 2.00 3.54 4.00 2.00 0.980 0.531 1.77 1.132 1/2-13 1/2-13 x 1.75 3.0

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for
O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

GQS
NPTF Port Square Block Flange Adapter
NPTF Port / Square Block Flange or Pad

O-ring Face Flat Face

STANDARD
K Dynamic
TUBE FITTING PT FLANGE C DRILL T MOUNTING Pressure
PART # THREAD SIZE A B MIN. D DIA. L THREAD X HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE NPTF (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B (in.) O-RING SHCS SX SS
12GQSB 12GQSP 3/4-14 0.75 2.25 1.12 1.250 0.75 0.406 1.25 3/8-16 1.438 2-214 3/8-16 x 2.00 5.0
16GQSB 16GQSP 1-11 1/2 1.00 3.00 1.50 1.560 1.00 0.531 1.50 1/2-13 2.000 2-219 1/2-13 x 2.25 5.0
20GQSB 20GQSP 1 1/4-11 1/2 1.25 3.00 1.50 1.750 1.25 0.531 1.50 1/2-13 2.000 2-222 1/2-13 x 2.25 4.0
24GQSB 24GQSP 1 1/2-11 1/2 1.50 4.00 2.00 2.115 1.50 0.656 1.75 5/8-11 2.750 2-225 5/8-11 x 2.75 3.0
32GQSB 32GQSP 2-11 1/2 2.00 4.00 2.00 2.490 2.00 0.656 1.75 5/8-11 2.750 2-228 5/8-11 x 2.75 2.7
40GQSB 40GQSP 2 1/2-8 2.50 5.50 2.75 2.995 2.50 0.906 2.25 7/8-9 3.750 2-232 7/8-9 x 3.50 2.5
48GQSB 48GQSP 3-8 3.00 5.50 2.75 3.615 3.00 0.906 2.25 7/8-9 3.750 2-237 7/8-9 x 3.50 1.2

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for O-ring Face
part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M25 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

W5SQS
Weld Socket Square Block Connector, Pipe
Pipe Weld Socket / Square Block Flange or Pad
How To
Order

O-ring Face Flat Face

Specs
STANDARD
K Dynamic
TUBE FITTING PIPE FLANGE C DRILL T MOUNTING Pressure
PART # SIZE SIZE A B MIN. D J DIA. L S THREAD X HARDWARE (x 1,000 PSI) Assembly /
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B (in.) O-RING SHCS SX SS Installation
12W5SQSB 12W5SQSP 3/4 0.75 2.25 1.12 1.250 0.75 0.50 0.406 1.00 1.062 3/8-16 1.438 2-214 3/8-16 x 1.75 5.0
16W5SQSB 16W5SQSP 1 1.00 3.00 1.50 1.560 1.00 0.50 0.531 1.00 1.328 1/2-13 2.000 2-219 1/2-13 x 1.75 5.0
20W5SQSB 20W5SQSP 1 1/4 1.25 3.00 1.50 1.750 1.25 0.50 0.531 1.00 1.672 1/2-13 2.000 2-222 1/2-13 x 1.75 4.0
24W5SQSB 24W5SQSP 1 1/2 1.50 4.00 2.00 2.115 1.50 0.62 0.656 1.25 1.922 5/8-11 2.750 2-225 5/8-11 x 2.25 3.0 Reference
32W5SQSB 32W5SQSP 2 2.00 4.00 2.00 2.490 2.00 0.62 0.656 1.25 2.406 5/8-11 2.750 2-228 5/8-11 x 2.25 3.0 Section
40W5SQSB 40W5SQSP 2 1/2 2.50 5.50 2.75 2.995 2.50 0.75 0.906 1.50 2.906 7/8-9 3.750 2-232 7/8-9 x 2.75 2.5
48W5SQSB 48W5SQSP 3 3.00 5.50 2.75 3.615 3.00 0.75 0.906 1.50 3.547 7/8-9 3.750 2-237 7/8-9 x 2.75 2.0

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for O-ring Face part
numbers and include 4 bolts, 4 lock washers and an O-ring.

PQ
Block Plug
Code 61/62 Block Flange or Pad Plug

O-ring Face Flat Face

STANDARD
K Dynamic
TUBE FITTING FLANGE DRILL T MOUNTING Pressure
PART # SIZE A B DIA. L THREAD HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS1
CODE 61 BLOCK FLANGE OR PAD PLUG
8PQ1B 8PQ1P 0.50 1.813 2.125 0.344 0.750 5/16-18 5/16-18 x 1.50 5.0
12PQ1B 12PQ1P 0.75 2.063 2.563 0.406 0.750 3/8-16 3/8-16 x 1.50 5.0
16PQ1B 16PQ1P 1.00 2.313 2.750 0.406 0.880 3/8-16 3/8-16 x 1.75 5.0
20PQ1B 20PQ1P 1.25 2.875 3.125 0.469 0.940 7/15-14 7/16-14 x 1.75 4.0
24PQ1B 24PQ1P 1.50 3.250 3.688 0.531 1.190 1/2-13 1/2-13 x 2.25 3.0
32PQ1B 32PQ1P 2.00 3.813 4.000 0.531 1.440 1/2-13 1/2-13 x 2.50 3.0
40PQ1B 40PQ1P 2.50 4.281 4.500 0.531 1.815 1/2-13 1/2-13 x 2.75 2.5
48PQ1B 48PQ1P 3.00 5.156 5.313 0.656 2.190 5/8-11 5/8-11 x 3.50 2.0
56PQIB 56PQ1P 3.50 5.500 6.000 0.656 1.440 5/8-11 5/8-11 x 2.75 0.5
64PQIB 64PQIP 4.00 6.000 6.380 0.656 1.440 5/8-11 5/8-11 x 2.75 0.5
CODE 62 BLOCK FLANGE OR PAD PLUG
8PQ2B 8PQ2P 0.50 1.940 2.300 0.344 1.250 5/16-18 5/16-18 x 2.00 6.0
12PQ2B 12PQ2P 0.75 2.500 2.950 0.406 1.250 3/8-16 3/8-16 x 2.00 6.0
16PQ2B 16PQ2P 1.00 2.750 3.190 0.469 1.500 7/16-14 7/16-14 x 2.50 6.0
20PQ2B 20PQ2P 1.25 3.060 3.750 0.531 1.430 1/2-13 1/2-13 x 2.50 6.0
24PQ2B 24PQ2P 1.50 3.750 4.440 0.656 1.815 5/8-11 5/8-11 x 3.00 6.0
32PQ2B 32PQ2P 2.00 4.500 5.250 0.781 1.815 3/4-10 3/4-10 x 3.00 6.0
40PQ2B2 40PQ2P2 2.50 5.870 6.870 0.940 1.930 7/8-9 7/8-9 x 3.50 6.0
48PQ2B2 48PQ2P2 3.00 7.000 8.500 1.190 2.690 1 1/8-7 1 1/8-7 x 4.50 6.0
1) See page M38 for standard stainless steel sizes and dimensions.
2) SAE J518 does not cover these sizes in Code 62. Bolt hole centerline dimensions are: 2.312” x 4.875” for
4OPQ2 and 2.812” x 6.000” for 48PQ2.
To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits
are available for O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M26 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

SPGG5
Flange Spacer with Gage Ports
Code 61/62 Spacer with Side Gage Ports
How To
Order

STANDARD
K Dynamic
TUBE FLANGE DRILL Pressure
Specs
FITTING SIZE A B D DIA. L (x 1,000 PSI)
PART # (in.) (in.) (in.) (in.) (in.) (in.) SX SS
CODE 61 O-RING SPACER
8SPGG5Q1B 0.50 1.813 2.125 0.500 0.344 1.25 5.0
12SPGG5Q1B 0.75 2.063 2.563 0.750 0.406 1.25 5.0 Assembly /
Installation
16SPGG5Q1B 1.00 2.313 2.750 1.000 0.406 0.88 5.0
20SPGG5Q1B 1.25 2.875 3.125 1.250 0.469 0.94 4.0
24SPGG5Q1B 1.50 3.250 3.688 1.500 0.531 1.19 3.0
32SPGG5Q1B 2.00 3.813 4.000 2.000 0.531 1.38 3.0
Reference
40SPGG5Q1B 2.50 4.281 4.500 2.500 0.531 1.75 2.5
Section
48SPGG5Q1B 3.00 5.156 5.313 3.000 0.656 2.12 2.0
CODE 62 O-RING SPACER
8SPGG5Q2B 0.50 1.940 2.300 0.500 0.344 1.25 6.0
12SPGG5Q2B 0.75 2.500 2.950 0.750 0.406 1.25 6.0
16SPGG5Q2B 1.00 2.750 3.190 1.000 0.469 1.50 6.0
20SPGG5Q2B 1.25 3.060 3.750 1.250 0.531 1.50 6.0
24SPGG5Q2B 1.50 3.750 4.440 1.500 0.656 1.75 6.0
32SPGG5Q2B 2.00 4.500 5.250 2.000 0.781 1.75 6.0

CP
Flange Connector Plate
Code 61/62 Flange Connector Plate

STANDARD
K Dynamic
TUBE FLANGE DRILL Pressure
FITTING SIZE A B D DIA. (x 1,000 PSI)
PART # (in.) (in.) (in.) (in.) (in.) SX SS
CODE 61 FLANGE CONNECTOR PLATE
8CP1 0.50 1.81 2.12 0.50 0.344 5.0
12CP1 0.75 2.06 2.56 0.75 0.406 5.0
16CP1 1.00 2.31 2.75 1.00 0.406 5.0
20CP1 1.25 2.88 3.12 1.25 0.469 4.0
24CP1 1.50 3.25 3.69 1.50 0.531 3.0
32CP1 2.00 3.81 4.00 2.00 0.531 3.0
40CP1 2.50 4.12 4.44 2.50 0.531 2.5
48CP1 3.00 5.16 5.31 3.00 0.656 2.5
CODE 62 FLANGE CONNECTOR PLATE
12CP2 0.75 2.38 2.81 0.75 0.406 6.0
16CP2 1.00 2.75 3.19 1.00 0.469 6.0
20CP2 1.25 3.06 3.75 1.25 0.531 6.0
24CP2 1.50 3.75 4.44 1.50 0.656 6.0
32CP2 2.00 4.50 5.25 2.00 0.781 6.0

Dimensions and pressures for reference only, subject to change.

M27 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

LOVQ1 LOVQ2
Code 61 Flange 45° Elbow Code 62 Flange 45° Elbow
Code 61 / ORFS Code 62 / ORFS
How To
Order

* Y – Across Wrench Flats * Y – Across Wrench Flats Specs

STANDARD STANDARD
Dynamic Dynamic
TUBE END SIZE Pressure TUBE END SIZE Pressure
FITTING 1 2 C E M1 N1 Y (x 1,000 PSI) FITTING 1 2 C E M1 N1 Y (x 1,000 PSI) Assembly /
PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) -S PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) -S Installation
12 LOVQ1 3/4 3/4 1.500 0.265 1.20 1.58 1 7/16 5.0 12 LOVQ2 3/4 3/4 1.625 0.345 1.20 1.83 1 7/16 6.0
16 LOVQ1 1 1 1.750 0.315 1.26 1.85 1 5/8 5.0 16 LOVQ2 1 1 1.875 0.375 1.25 2.07 1 5/8 6.0
20 LOVQ1 1 1/4 1 1/4 2.000 0.315 1.29 2.40 1 7/8 4.0 20 LOVQ2 1 1/4 1 1/4 2.125 0.405 1.29 2.40 1 7/8 5.0
24 LOVQ1 1 1/2 1 1/2 2.375 0.315 1.45 2.90 2 1/2 3.0 24 LOVQ2 1 1/2 1 1/2 2.500 0.495 1.45 2.90 2 1/2 4.5 Reference
Section

XVQ1 XVQ2
Code 61 Flange 45° Elbow Code 62 Flange 45° Elbow
Code 61 / 37° Flare Code 62 / 37° Flare

* Y – Across Wrench Flats * Y – Across Wrench Flats

STANDARD STANDARD
Dynamic Dynamic
TUBE END SIZE Pressure TUBE END SIZE Pressure
FITTING 1 2 C E M1 N1 Y (x 1,000 PSI) FITTING 1 2 C E M1 N1 Y (x 1,000 PSI)
PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) -S PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) -S
12 XVQ1 3/4 3/4 1.500 0.265 1.27 1.58 1 7/16 5.0 12 XVQ2 3/4 3/4 1.625 0.345 1.27 1.83 1 7/16 5.0
16 XVQ1 1 1 1.750 0.315 1.47 1.85 1 5/8 5.0 16 XVQ2 1 1 1.875 0.375 1.47 2.07 1 5/8 5.0
20 XVQ1 1 1/4 1 1/4 2.000 0.315 1.59 2.40 1 7/8 4.0 20 XVQ2 1 1/4 1 1/4 2.125 0.405 1.59 2.40 1 7/8 4.0
24 XVQ1 1 1/2 1 1/2 2.375 0.315 1.78 2.90 2 1/2 3.0 24 XVQ2 1 1/2 1 1/2 2.500 0.495 1.78 2.90 2 1/2 3.0
32 XVQ1 2 2 2.812 0.375 2.22 3.00 2 1/2 2.0

BUVQ1
Code 61 45° Elbow
Code 61 / Flareless

* Y – Across Wrench Flats

STANDARD
Dynamic
TUBE END SIZE Pressure
FITTING 1 2 C E M1 N1 Y (x 1,000 PSI)
PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) -S
12 BUVQ1 3/4 3/4 1.500 0.265 1.27 1.58 1 7/16
16 BUVQ1 1 1 1.750 0.315 1.36 1.85 1 5/8
20 BUVQ1 1 1/4 1 1/4 2.000 0.315 1.45 2.40 1 7/8
24 BUVQ1 1 1/2 1 1/2 2.375 0.315 1.52 2.90 2 1/2
32 BUVQ1 2 2 2.812 0.375 1.83 3.00 2 1/2

Dimensions and pressures for reference only, subject to change.

M28 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

LOEQ1 LOEQ2
Code 61 Flange 90° Elbow Code 62 Flange 90° Elbow
Code 61 / ORFS Code 62 / ORFS
How To
Order

* Y – Across Wrench Flats * Y – Across Wrench Flats

Specs
STANDARD STANDARD
Dynamic Dynamic
TUBE END SIZE Pressure TUBE END SIZE Pressure
FITTING 1 2 C E M N Y (x 1,000 PSI) FITTING 1 2 C E M N Y (x 1,000 PSI)
PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) -S PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) -S Assembly /
12 LOEQ1 3/4 3/4 1.500 0.265 1.95 1.81 1 3/16 5.0 12 LOEQ2 3/4 3/4 1.625 0.345 2.01 2.01 1 3/16 6.0 Installation
16 LOEQ1 1 1 1.750 0.315 2.05 2.13 1 7/16 5.0 16 LOEQ2 1 1 1.875 0.375 2.17 2.42 1 7/16 6.0
20 LOEQ1 1 1/4 1 1/4 2.000 0.315 2.22 2.26 1 5/8 4.0 20 LOEQ2 1 1/4 1 1/4 2.125 0.405 2.50 2.68 1 5/8 5.0
24 LOEQ1 1 1/2 1 1/2 2.375 0.315 2.54 2.64 2 3.0 24 LOEQ2 1 1/2 1 1/2 2.500 0.495 2.87 3.13 2 4.5
Reference
Section

XEQ1 XEQ2
Code 61 Flange 90° Elbow Code 62 Flange 90° Elbow
Code 61 / 37° Flare Code 62 / 37° Flare

* Y – Across Wrench Flats * Y – Across Wrench Flats

STANDARD STANDARD
Dynamic Dynamic
TUBE END SIZE Pressure TUBE END SIZE Pressure
FITTING 1 2 C E M N Y (x 1,000 PSI) FITTING 1 2 C E M N Y (x 1,000 PSI)
PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) -S -SS -B PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) -S -SS -B
12 XEQ1 3/4 3/4 1.500 0.265 1.91 1.81 1 3/16 5.0 12 XEQ2 3/4 3/4 1.625 0.345 1.97 2.04 1 3/16 5.0
16 XEQ1 1 1 1.750 0.315 2.07 2.13 1 7/16 5.0 16 XEQ2 1 1 1.875 0.375 2.19 2.42 1 7/16 5.0
20 XEQ1 1 1/4 1 1/4 2.000 0.315 2.26 2.26 1 5/8 4.0 20 XEQ2 1 1/4 1 1/4 2.125 0.405 2.56 2.68 1 5/8 4.0
24 XEQ1 1 1/2 1 1/2 2.375 0.315 2.72 2.64 2 3.0 24 XEQ2 1 1/2 1 1/2 2.500 0.495 3.03 3.13 2 3.0
32 XEQ1 2 2 2.812 0.375 3.06 4.25 2 1/2 2.0

BUEQ1
Code 61 90° Elbow
Code 61 / Flareless

* Y – Across Wrench Flats

STANDARD
Dynamic
TUBE END SIZE Pressure
FITTING 1 2 C E M N Y (x 1,000 PSI)
PART # (in.) (in.) (in.) (in.) (in.) (in.) (in.) -S -SS -B
12 BUEQ1 3/4 3/4 1.500 0.265 1.73 1.81 1 3/16
16 BUEQ1 1 1 1.750 0.315 1.99 2.13 1 7/16
20 BUEQ1 1 1/4 1 1/4 2.000 0.315 1.99 2.26 1 5/8
24 BUEQ1 1 1/2 1 1/2 2.375 0.315 2.33 2.64 2
32 BUEQ1 2 2 2.812 0.375 2.45 4.25 2 1/2

Dimensions and pressures for reference only, subject to change.

M29 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

W7EQ
Weld Socket Block Elbow Connector, Pipe
Weld Socket, Pipe / Code 61 or 62
Block Flange or Pad How To
Order

Specs

Assembly /
Installation

O-ring Face Flat Face Reference

Section
STANDARD
K Dynamic
TUBE FITTING PIPE FLANGE DRILL T MOUNTING Pressure
PART # SIZE SIZE A B D E J DIA. L M N S THREAD HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS
WELD SOCKET, PIPE / CODE 61 BLOCK FLANGE OR PAD
12W7EQ1B 12W7EQ1P 3/4 0.75 1.69 2.56 0.75 1.25 0.56 0.406 2.28 1.44 0.875 1.062 3/8-16 3/8-16 x 2.00 5.0
16W7EQ1B 16W7EQ1P 1 1.00 1.94 2.75 1.00 1.50 0.56 0.406 2.62 1.66 1.062 1.328 3/8-16 3/8-16 x 2.25 4.5
20W7EQ1B 20W7EQ1P 1 1/4 1.25 2.19 3.12 1.25 1.81 0.62 0.469 3.00 1.91 1.188 1.672 7/16-14 7/16-14 x 2.75 3.5
24W7EQ1B 24W7EQ1P 1 1/2 1.50 2.56 3.69 1.50 2.00 0.69 0.531 3.33 2.05 1.312 1.922 1/2-13 1/2-13 x 3.00 3.0
32W7EQ1B 32W7EQ1P 2 2.00 3.06 4.33 2.00 2.50 0.75 0.531 3.81 2.28 1.656 2.406 1/2-13 1/2-13 x 3.50 3.0
WELD SOCKET, PIPE / CODE 62 BLOCK FLANGE OR PAD
12W7EQ2B 12W7EQ2P 3/4 0.75 1.94 2.75 0.75 1.50 0.56 0.406 2.62 1.66 1.062 1.062 3/8-16 3/8-16 x 2.25 6.0
16W7EQ2B 16W7EQ2P 1 1.00 2.19 3.12 1.00 1.81 0.62 0.469 3.00 1.91 1.188 1.328 7/16-14 7/16-14 x 2.50 6.0
20W7EQ2B 20W7EQ2P 1 1/4 1.25 2.56 3.69 1.25 2.00 0.69 0.531 3.32 2.05 1.312 1.672 1/2-13 1/2-13 x 3.00 5.0
24W7EQ2B 24W7EQ2P 1 1/2 1.50 3.06 4.33 1.50 2.50 0.75 0.656 3.81 2.28 1.656 1.922 5/8-11 5/8-11 x 3.50 5.0

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for O-ring Face part
numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M30 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

WFS
SAE Flange Connection
Code 61 & 62 / Metric Flareless
How To
Order

Specs
TUBE END WORKING L1 L2 STANDARD STANDARD
FITTING SIZE SIZE PRESSURE M d1 I I1 I2 I3 ~
~ ~
~ S1 S2 S3 S6 FROM STOCK FROM STOCK
PART # (in.) (mm) (bar) THREAD (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) A3C 71 A3C 71
SAE FLANGE CONNECTIONS – CODE 61 – STANDARD SERIES
WFS32/15LA3C 1/2 15L 200 M22 x 1.5 12 11.5 41 29 36 56 44 24 27 24 6 · · Assembly /
WFS32/16SA3C 1/2 16S 220 M24 x 1.5 12 11.5 41.5 29.5 36 60 48 24 30 24 6 · · Installation
WFS33/18LA3C 3/4 18L 200 M26 x 1.5 15 15.5 45.5 31.5 42 62 48 30 32 30 8 · ·
WFS33/22LA3C 3/4 22L 100 M30 x 2 19 15.5 45.5 33.5 42 62 50 30 36 30 8 · ·
WFS33/20SA3C 3/4 20S 220 M30 x 2 16 15.5 46.5 32.5 42 68 54 30 36 30 8 · ·
WFS33/25SA3C 3/4 25S 220 M36 x 2 17 15.5 45 33 42 69 57 30 46 30 8 · · Reference
WFS34/28LA3C 1 28L 100 M36 x 2 24 13.5 46.5 36.5 45 63 53 36 41 36 8 · · Section
WFS34/30SA3C 1 30S 220 M42 x 2 24 13.5 49.5 36.5 45 76 63 36 50 36 8 · ·
WFS35/35LA3C 1 1/4 35L 100 M45 x 2 30 18.5 47.5 46.5 50 69 68 41 50 41 8 · ·
WFS35/25SA3C 1 1/4 25S 175 M36 x 2 20 18.5 48 43 50 72 67 41 46 41 8 · ·
WFS35/30SA3C 1 1/4 30S 175 M42 x 2 25 18.5 48.5 43.5 50 75 70 41 50 41 8 · ·
WFS35/38SA3C 1 1/4 38S 175 M52 x 2 28 18.5 50 43 50 81 74 46 60 41 8 · ·
WFS36/42LA3C 1 1/2 42L 100 M52 x 2 36 18.5 53 47 55 76 70 46 60 50 10 · ·
WFS36/38SA3C 1 1/2 38S 130 M52 x 2 32 18.5 54 48 55 85 79 46 60 50 10 · ·
SAE FLANGE CONNECTIONS – CODE 62 – HIGH PRESSURE SERIES
WFS62/16SA3C 1/2 16S 250 M24 x 1.5 12 13.5 44.5 29.5 39 63 48 24 30 24 6 · ·
WFS63/16SA3C 3/4 16S 250 M24 x 1.5 12 15.5 50.5 36.5 48 69 55 30 30 32 8 · ·
WFS63/20SA3C 3/4 20S 250 M30 x 2 16 15.5 50.5 35.5 48 72 57 30 36 32 8 · ·
WFS63/25SA3C 3/4 25S 250 M36 x 2 17 15.5 51 36 48 75 60 30 46 32 8 · ·
WFS64/25SA3C 1 25S 250 M36 x 2 20 20.5 60 44 60 84 65 36 46 41 10 · ·
WFS64/30SA3C 1 30S 250 M42 x 2 24 20.5 60.5 41.5 60 87 68 36 50 41 10 · ·
WFS65/30SA3C 1 1/4 30S 250 M42 x 2 25 22.5 65.5 44.5 68 92 71 41 50 46 10 · ·
WFS65/38SA3C 1 1/4 38S 200 M52 x 2 30 22.5 67 45 68 98 76 46 60 46 10 · ·
WFS66/38SA3C 1 1/2 38S 200 M52 x 2 30 24.5 73 56 76 104 87 46 60 50 14 · ·

EO-2 Part Number example: WFS33/18ZLA3C

Temperature range without pressure reductions for fittings with O-ring sealing of NBR (e.g., buna N series) -35°C up to +100°C,
FPM (e.g., fluorocarbon on request) -25°C up to +120°C.
Tightening torques for socket head cap screws see Tables T6 and T7.

Dimensions and pressures for reference only, subject to change.

M31 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

BFW
Hydraulic Flange Elbow
DIN Flange / Metric Flareless
How To
Order

Specs

STANDARD STANDARD
TUBE WORKING END MATERIAL EO-2
FITTING PRESSURE SIZE h1 h1 I L1 L2 LK S2 t FROM STOCK FROM STOCK Assembly /
PART # (bar) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) A3C 71 A3C 71 Installation
BFW15L/LK40A3C 65 15 22.5 36.5 38 42 46 40 27 7 • •
BFW18L/LK40A3C 65 18 22.5 36.5 38 42 47 40 32 7.5 • •
BFW22L/LK40A3C 65 22 22.5 36.5 38 42 47.5 40 36 7.5 • •
BFW28L/LK40A3C 65 28 28 43 40 42 49 40 41 7.5 • • Reference
Section
BFW35L/LK40A3C 65 35 32 55 41 42 52 40 50 10.5 • •
BFW35L/LK55A3C 65 35 32 51.5 49 58 62 55 50 10.5 • •
BFW42L/LK55A3C 65 42 40 64.5 49 58 61 55 60 11 • •
BFW15L/LK35A3C 155 15 16.5 26.5 38 39 46 35 27 7 • •
BFW20S/LK55A3C 155 20 24 38 45 58 56 55 36 10.5 • •
BFW20S/LK40A3C 155 20 22.5 35.5 40 42 50 40 36 10.5 • •
BFW25S/LK55A3C 155 25 30 46 49 58 61 55 46 12 • •
BFW30S/LK55A3C 155 30 32 50 49 58 62 55 50 13.5 • •
BFW10L/LK35A3C 200 10 16.5 26.5 38 39 47 35 19 7 • •
BFW12L/LK35A3C 200 12 16.5 26.5 38 39 47 35 22 7 • •
BFW16S/LK35A3C 200 16 20 31 38 39 48 35 30 8.5 • •

Unassembled BFW Fitting Components

3 5 6 7
1 2 Progressive 4 2 Cap Screws 2 Cap Screws 4 Spr. Washers
Elbow Body Nut Ring O-Ring DIN 912-8.8 DIN 912-8.8 DIN 127
BFW15L/LK40A3CX M15LA3CX DPR15LA3CX OR26X2.5X M6X22 M6X22 A6
BFW18L/LK40A3CX M18LA3CX DPR18LA3CX OR26X2.5X M6X22 M6X22 A6
BFW22L/LK40A3CX M22LA3CX DPR22LA3CX OR26X2.5X M6X22 M6X22 A6
BFW28L/LK40A3CX M28LA3CX DPR28LA3CX OR26X2.5X M6X20 M6X50 A6
BFW35L/LK40A3CX M35LA3CX DPR35LA3CX OR26X2.5X M6X22 M6X60 A6
BFW35L/LK55A3CX M35LA3CX DPR35LA3CX OR33X2.5X M8X25 M8X60 A8
BFW42L/LK55A3CX M42LA3CX DPR42LA3CX OR33X2.5X M8X25 M8X70 A8
BFW15L/LK35A3CX M15LA3CX DPR15LA3CX OR20X2.5X M6X22 M6X35 A6
BFW20S/LK55A3CX M20SA3CX DPR20SA3CX OR33X2.5X M8X25 M8X50 A8
BFW20S/LK40A3CX M20SA3CX DPR20SA3CX OR26X2.5X M6X22 M6X45 A6
BFW25S/LK55A3CX M25SA3CX DPR25SA3CX OR33X2.5X M8X25 M8X55 A8
BFW30S/LK55A3CX M30SA3CX DPR20SA3CX OR33X2.5X M8X25 M8X55 A8
BFW10L/LK35A3CX M10LA3CX DRP10LA3CX OR20X2.5X M6X22 M6X35 A6
BFW12L/LK35A3CX M12LA3CX DPR12LA3CX OR20X2.5X M6X22 M6X35 A6
BFW16S/LK35A3CX M16SA3CX DPR16SA3CX OR20X2.5X M6X22 M6X40 A6
BFW20S/LK35A3CX M20SA3CX DPR20SA3CX OR20X2.5X M6X22 M6X45 A6

EO-2 Part Number example: BFW15ZL/LK40A3C

Temperature range without pressure reductions for fittings with O-ring sealing of NBR (e.g., buna N series)
-35°C up to +100°C, FPM (e.g., fluorocarbon on request) -25°C up to +120°C.
Tightening torques for socket head cap screws see Table T6.

Dimensions and pressures for reference only, subject to change.

M32 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

QPQPJQ
Block Junction Tee
Code 61 or 62 Block Pads / Block Flange or Pad
How To
Order

O-ring Face Flat Face

STANDARD Specs
K Dynamic
TUBE FITTING FLANGE DRILL T Pressure
PART # SIZE A B D DIA. L THREAD (x 1,000 PSI)
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SX SS
CODE 61 BLOCK PADS / BLOCK FLANGE OR PAD Assembly /
12Q1PQ1PJQ1B 12Q1PQ1PJQ1P 0.75 2.62 2.75 0.75 0.406 2.25 3/8-16 5.0 Installation
16Q1PQ1PJQ1B 16Q1PQ1PJQ1P 1.00 2.82 3.00 1.00 0.406 2.50 3/8-16 5.0
20Q1PQ1PJQ1B 20Q1PQ1PJQ1P 1.25 3.19 3.50 1.25 0.469 3.00 7/16-14 4.0
24Q1PQ1PJQ1B 24Q1PQ1PJQ1P 1.50 3.75 4.00 1.50 0.531 3.50 1/2-13 3.0
Reference
32Q1PQ1PJQ1B 32Q1PQ1PJQ1P 2.00 4.00 4.25 2.00 0.531 4.00 1/2-13 3.0
Section
CODE 62 BLOCK PADS / BLOCK FLANGE OR PAD
12Q2PQ2PJQ2B 12Q2PQ2PJQ2P 0.75 2.81 3.00 0.75 0.406 2.50 3/8-16 6.0
16Q2PQ2PJQ2B 16Q2PQ2PJQ2P 1.00 3.19 3.50 1.00 0.469 3.00 7/16-14 6.0
20Q2PQ2PJQ2B 20Q2PQ2PJQ2P 1.25 3.75 4.00 1.25 0.531 3.50 1/2-13 6.0
24Q2PQ2PJQ2B 24Q2PQ2PJQ2P 1.50 4.50 4.50 1.50 0.656 4.00 5/8-11 6.0
32Q2PQ2PJQ2B 32Q2PQ2PJQ2P 2.00 5.25 5.00 1.94 0.781 5.00 3/4-10 6.0

G5EQ
SAE Port Block Elbow
SAE Port / Code 61 or 62 Block Flange or Pad

O-ring Face Flat Face

STANDARD
T5 SAE K Dynamic
TUBE FITTING STRAIGHT PORT FLANGE DRILL T MOUNTING Pressure
PART # THREAD DASH SIZE A B D E DIA. L M N THREAD HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE UN-2B SIZE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS
SAE PORT / CODE 61 BLOCK FLANGE OR PAD
12G5EQ1B 12G5EQ1P 1-1/16-12 12 0.75 1.69 2.56 0.75 1.25 0.406 2.28 1.440 0.875 3/8-16 3/8-16 x 2.00 4.0
16G5EQ1B 16G5EQ1P 1-5/16-12 16 1.00 1.94 2.75 1.00 1.50 0.406 2.62 1.660 1.062 3/8-16 3/8-16 x 2.25 3.0
20G5EQ1B 20G5EQ1P 1-5/8-12 20 1.25 2.19 3.12 1.25 1.81 0.469 3.00 1.910 1.188 7/16-14 7/16-14 x 2.75 2.5
24G5EQ1B 24G5EQ1P 1-7/8-12 24 1.50 2.56 3.69 1.50 2.00 0.531 3.33 2.050 1.312 1/2-13 1/2-13 x 3.00 2.0
32G5EQ1B 32G5EQ1P 2-1/2-12 32 2.00 3.06 4.33 2.00 2.50 0.531 3.81 2.280 1.656 1/2-13 1/2-13 x 3.50 1.5
SAE PORT / CODE 62 BLOCK FLANGE OR PAD
12G5EQ2B 12G5EQ2P 1-1/16-12 12 0.75 1.94 2.75 0.75 1.50 0.406 2.62 1.660 1.062 3/8-16 3/8-16 x 2.25 5.0
16G5EQ2B 16G5EQ2P 1-5/16-12 16 1.00 2.19 3.12 1.00 1.81 0.469 3.00 1.910 1.188 7/16-14 7/16-14 x 2.50 4.0
20G5EQ2B 20G5EQ2P 1-5/8-12 20 1.25 2.56 3.69 1.25 2.00 0.531 3.32 2.050 1.312 1/2-13 1/2-13 x 3.00 3.5
24G5EQ2B 24G5EQ2P 1-7/8-12 24 1.50 3.06 4.33 1.50 2.50 0.656 3.81 2.280 1.656 5/8-11 5/8-11 x 3.50 3.5

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are
available for O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M33 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

GEQ
NPTF Port Block Elbow Adapter
NPTF / Code 61 or 62 Block Flange or Pad
How To
Order

Specs

Assembly /
Installation

O-ring Face Flat Face

Reference
STANDARD Section
K Dynamic
TUBE FITTING PT FLANGE DRILL T MOUNTING Pressure
PART # THREAD SIZE A B D E DIA. L M N THREAD HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE NPTF (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS
NPTF PORT / CODE 61 BLOCK FLANGE OR PAD
12GEQ1B 12GEQ1P 3/4 - 14 0.75 1.69 2.56 0.75 1.25 0.406 2.28 1.440 0.875 3/8-16 3/8-16 x 2.00 4.0
16GEQ1B 16GEQ1P 1 - 11 1/2 1.00 1.94 2.75 1.00 1.50 0.406 2.62 1.660 1.062 3/8-16 3/8-16 x 2.25 4.0
20GEQ1B 20GEQ1P 1 1/4 - 11 1/2 1.25 2.19 3.12 1.25 1.81 0.469 3.00 1.910 1.188 7/16-14 7/16-14 x 2.75 2.7
24GEQ1B 24GEQ1P 1 1/2 - 11 1/2 1.50 2.56 3.69 1.50 2.00 0.531 3.33 2.050 1.312 1/2-13 1/2-13 x 3.00 2.5
32GEQ1B 32GEQ1P 2 - 11 1/2 2.00 3.06 4.33 2.00 2.50 0.531 3.81 2.280 1.656 1/2-13 1/2-13 x 3.50 1.7
NPTF PORT / CODE 62 BLOCK FLANGE OR PAD
12GEQ2B 12GEQ2P 3/4 - 14 0.75 1.94 2.75 0.75 1.50 0.406 2.62 1.660 1.062 3/8-16 3/8-16 x 2.25 5.5
16GEQ2B 16GEQ2P 1 - 11 1/2 1.00 2.19 3.12 1.00 1.81 0.469 3.00 1.910 1.188 7/16-14 7/16-14 x 2.50 5.0
20GEQ2B 20GEQ2P 1 1/4 - 11 1/2 1.25 2.56 3.69 1.25 2.00 0.531 3.32 2.050 1.312 1/2-13 1/2-13 x 3.00 3.5
24GEQ2B 24GEQ2P 1 1/2 - 11 1/2 1.50 3.06 4.33 1.50 2.50 0.656 3.81 2.280 1.656 5/8-11 5/8-11 x 3.50 3.0

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for
O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M34 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

W6EQ
Weld Socket Block Elbow Connector, Tube
Weld Socket, Tube / Code 61 or 62 Block Flange or Pad
How To
Order

Specs

Assembly /
Installation

O-ring Face Flat Face

Reference
STANDARD
K Dynamic
Section
TUBE FITTING TUBE FLANGE DRILL T MOUNTING Pressure
PART # O.D. SIZE A B D D1 E J DIA. L M N S THREAD HARDWARE (x 1,000 PSI )
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SX SS
WELD SOCKET, TUBE / CODE 61 BLOCK FLANGE OR PAD
12W6EQ1B 12W6EQ1P 3/4 0.75 1.69 2.56 0.75 0.63 1.25 0.312 0.406 2.280 1.44 0.875 0.752 3/8-16 3/8-16 x 2.00 5.0
16-12W6EQ1B 16-12W6EQ1P 1 0.75 1.69 2.56 0.75 0.75 1.25 0.438 0.406 2.280 1.44 0.875 1.002 3/8-16 3/8-16 x 2.00 5.0
16W6EQ1B 16W6EQ1P 1 1.00 1.94 2.75 1.00 0.88 1.50 0.438 0.406 2.620 1.66 1.062 1.002 3/8-16 3/8-16 x 2.25 5.0
20-16W6EQ1B 20-16W6EQ1P 1 1/4 1.00 1.94 2.75 1.00 1.00 1.50 0.500 0.406 2.620 1.66 1.062 1.252 3/8-16 3/8-16 x 2.25 5.0
20W6EQ1B 20W6EQ1P 1 1/4 1.25 2.19 3.12 1.25 1.13 1.81 0.500 0.469 3.000 1.91 1.188 1.252 7/16-14 7/16-14 x 2.75 4.0
24-20W6EQ1B 24-20W6EQ1P 1 1/2 1.25 2.19 3.12 1.25 1.25 1.81 0.562 0.469 3.000 1.91 1.188 1.502 7/16-14 7/16-14 x 2.75 4.0
24W6EQ1B 24W6EQ1P 1 1/2 1.50 2.56 3.69 1.50 1.38 2.00 0.562 0.531 3.328 2.05 1.312 1.502 1/2-13 1/2-13 x 3.00 3.0
28-24W6EQ1B 28-24W6EQ1P 1 3/4 1.50 2.56 3.69 1.50 1.50 2.00 0.562 0.531 3.328 2.05 1.312 1.752 1/2-13 1/2-13 x 3.00 3.0
32W6EQ1B 32W6EQ1P 2 2.00 3.06 4.33 2.00 1.88 2.50 0.625 0.531 3.812 2.28 1.656 2.002 1/2-13 1/2-13 x 3.50 3.0
36-32W6EQ1B 36-32W6EQ1P 2 1/4 2.00 3.06 4.33 2.00 2.00 2.50 0.625 0.531 3.812 2.28 1.656 2.252 1/2-13 1/2-13 x 3.50 3.0
WELD SOCKET, TUBE / CODE 62 BLOCK FLANGE OR PAD
12W6EQ2B 12W6EQ2P 3/4 0.75 1.94 2.75 0.75 0.63 1.50 0.560 0.406 2.620 1.66 1.062 0.752 3/8-16 3/8-16 x 2.25 6.0
16-12W6EQ2B 16-12W6EQ2P 1 0.75 1.94 2.75 0.75 0.75 1.50 0.620 0.406 2.620 1.66 1.062 1.002 3/8-16 3/8-16 x 2.25 6.0
16W6EQ2B 16W6EQ2P 1 1.00 2.19 3.12 1.00 0.88 1.81 0.620 0.469 3.000 1.91 1.188 1.002 7/16-14 7/16-14 x 2.50 6.0
20-16W6EQ2B 20-16W6EQ2P 1 1/4 1.00 2.19 3.12 1.00 1.00 1.81 0.690 0.469 3.000 1.91 1.188 1.252 7/16-14 7/16-14 x 2.50 6.0
20W6EQ2B 20W6EQ2P 1 1/4 1.25 2.56 3.69 1.25 1.13 2.00 0.690 0.531 3.320 2.05 1.312 1.252 1/2-13 1/2-13 x 3.00 6.0
24-20W6EQ2B 24-20W6EQ2P 1 1/2 1.25 2.56 3.69 1.25 1.25 2.00 0.750 0.531 3.320 2.05 1.312 1.502 1/2-13 1/2-13 x 3.00 6.0
24W6EQ2B 24W6EQ2P 1 1/2 1.50 3.06 4.33 1.50 1.38 2.50 0.750 0.656 3.810 2.28 1.656 1.502 5/8-11 5/8-11 x 3.50 6.0
28-24W6EQ2B 28-24W6EQ2P 1 3/4 1.50 3.06 4.33 1.50 1.50 2.50 0.750 0.656 3.810 2.28 1.656 1.752 5/8-11 5/8-11 x 3.50 6.0

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for O-ring Face part
numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M35 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

G5Q – Stainless Steel

SAE Port Block Flange Adapter
SAE Port / Code 61 or 62 Block Flange
How To
Order

O-ring Face Flat Face

Specs
STANDARD
SAE K T5 Dynamic
TUBE FITTING PORT FLANGE DRILL STRAIGHT MOUNTING Pressure
PART # DASH SIZE A B D DIA. L THREAD HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE SIZE (in.) (in.) (in.) (in.) (in.) (in.) UN-2B SHCS SS Assembly /
SAE PORT / CODE 61 FLANGE BLOCK Installation
8G5Q1B * 8 0.50 1.50 2.12 0.50 0.344 1.20 3/4-16 5/16-18 x 1.25 5.0
12G5Q1B * 12 0.75 1.75 2.62 0.75 0.406 1.20 1 1/16-12 3/8-16 x 1.50 5.0
16G5Q1B * 16 1.00 2.00 2.82 1.00 0.406 1.45 1 5/16-12 3/8-16 x 1.50 5.0
20G5Q1B * 20 1.25 2.50 3.19 1.25 0.469 1.45 1 5/8-12 7/16-14 x 1.75 4.0
Reference
Section
24G5Q1B * 24 1.50 2.75 3.75 1.50 0.531 1.70 1 7/8-12 1/2-13 x 2.00 3.0
32G5Q1B * 32 2.00 3.25 4.00 2.00 0.531 1.70 1 7/8-12 1/2-13 x 2.00
SAE PORT / CODE 62 FLANGE BLOCK
8G5Q2B * 8 0.50 1.75 2.22 0.50 0.344 0.95 3/4-16 5/16-18 x 1.25 6.0
12G5Q2B * 12 0.75 2.00 2.81 0.75 0.406 1.20 1 1/16-12 3/8-16 x 1.50 6.0
16G5Q2B * 16 1.00 2.25 3.19 1.00 0.469 1.45 1 5/16-12 7/16-14 x 1.75 6.0
20G5Q2B * 20 1.25 2.75 3.75 1.25 0.531 1.45 1 5/8-12 1/2-13 x 1.75 6.0
24G5Q2B * 24 1.50 3.25 4.50 1.50 0.656 1.70 1 7/8-12 5/8-11 x 2.00 5.0
32G5Q2B * 32 2.00 4.00 5.25 2.00 0.781 1.70 2 1/2-12 3/4-10 x 2.25 3.0

* Consult factory.
To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are
available for O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

GQ – Stainless Steel
NPTF Port Block Flange Adapter
NPTF Port / Code 61 or 62 Block Flange

O-ring Face Flat Face

STANDARD
K Dynamic
TUBE FITTING PT FLANGE DRILL MOUNTING Pressure
PART # THREAD SIZE A B D DIA. L HARDWARE (x 1,000 PSI)
O-RING FACE FLAT FACE NPTF (in.) (in.) (in.) (in.) (in.) (in.) SHCS SS
NPTF PORT / CODE 61 BLOCK FLANGE
8GQ1B * 1/2-14 0.50 1.50 2.12 0.50 0.344 1.25 5/16-18 x 1.75 5.0
12GQ1B * 3/4-14 0.75 1.75 2.62 0.75 0.406 1.25 3/8-16 x 2.00 5.0
16GQ1B * 1-11 1/2 1.00 2.00 2.82 1.00 0.406 1.50 3/8-16 x 2.25 5.0
20GQ1B * 1 1/4-11 1/2 1.25 2.50 3.19 1.25 0.469 1.50 7/16-14 x 2.25 4.0
24GQ1B * 1 1/2-11 1/2 1.50 2.75 3.75 1.50 0.531 1.75 1/2-13 x 2.50 3.0
32GQ1B * 2-11 1/2 2.00 3.25 4.00 2.00 0.531 1.75 1/2-13 x 2.50 2.7
40GQ1B * 2 1/2-8 2.50 4.00 4.50 2.50 0.531 2.00 1/2-13 x 2.75 2.5
48GQ1B * 3-8 3.00 4.50 5.31 3.00 0.656 2.25 5/8-11 x 3.00 1.2
NPTF PORT / CODE 62 BLOCK FLANGE
12GQ2B * 3/4-14 0.75 2.00 2.81 0.75 0.406 1.20 3/8-16 x 2.00 6.0
16GQ2B * 1-11 1/2 1.00 2.25 3.19 1.00 0.469 1.45 7/16-14 x 2.50 5.0
20GQ2B * 1 1/4-11 1/2 1.25 2.75 3.75 1.25 0.531 1.45 1/2-13 x 2.50 4.0
24GQ2B * 1 1/2-11 1/2 1.50 3.25 4.50 1.50 0.656 1.70 5/8-11 x 2.75 3.5
32GQ2B * 2-11 1/2 2.00 4.00 5.25 2.00 0.781 1.70 3/4-10 x 3.00 3.0
* Consult factory.
To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits
are available for O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M36 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

W5Q – Stainless Steel

Flat Weld Socket Block Flange Connector, Pipe
Flat Weld Socket, Pipe / Code 61 or 62
Block Flange or Pad How To
Order

O-ring Face Flat Face Specs

STANDARD
K Dynamic
TUBE FITTING PIPE FLANGE DRILL T MOUNTING Pressure
PART # SIZE SIZE A B D J DIA. L S THREAD HARDWARE (x 1,000 PSI) Assembly /
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SS Installation
FLAT WELD SOCKET, PIPE / CODE 61 BLOCK FLANGE OR PAD
8W5Q1B 8W5Q1P 1/2 0.50 1.50 2.12 0.500 0.380 0.344 0.69 0.860 5/16-18 5/16-18 x 1.25 5.0
12W5Q1B 12W5Q1P 3/4 0.75 1.75 2.62 0.750 0.500 0.406 0.94 1.070 3/8-16 3/8-16 x 1.75 5.0
16W5Q1B 16W5Q1P 1 1.00 2.00 2.82 1.000 0.500 0.406 0.94 1.335 3/8-16 3/8-16 x 1.75 5.0 Reference
20W5Q1B 20W5Q1P 1 1/4 1.25 2.50 3.19 1.250 0.500 0.469 0.94 1.680 7/16-14 7/16-14 x 1.75 4.0
Section
24W5Q1B 24W5Q1P 1 1/2 1.50 2.75 3.75 1.500 0.500 0.531 1.19 1.920 1/2-13 1/2-13 x 2.25 3.0
32W5Q1B 32W5Q1P 2 2.00 3.25 4.00 2.000 0.620 0.531 1.44 2.411 1/2-13 1/2-13 x 2.50 3.0
40W5Q1B 40W5Q1P 2 1/2 2.50 4.00 4.50 2.500 0.750 0.531 1.69 2.911 1/2-13 1/2-13 x 2.75 2.5
48W5Q1B 48W5Q1P 3 3.00 4.50 5.31 3.000 1.240 0.656 2.12 3.540 5/8-11 5/8-11 x 3.50 2.0
FLAT WELD SOCKET, PIPE / CODE 62 BLOCK FLANGE OR PAD
8W5Q2B 8W5Q2P 1/2 0.50 1.75 2.22 0.500 0.500 0.344 0.94 0.860 5/16-18 5/16-18 x 1.50 6.0
12W5Q2B 12W5Q2P 3/4 0.75 2.00 2.81 0.750 0.500 0.406 0.94 1.070 3/8-16 3/8-16 x 1.75 6.0
16W5Q2B 16W5Q2P 1 1.00 2.25 3.19 1.000 0.500 0.469 0.94 1.335 7/16-14 7/16-14 x 1.75 6.0
20W5Q2B 20W5Q2P 1 1/4 1.25 2.75 3.75 1.250 0.500 0.531 1.19 1.672 1/2-13 1/2-13 x 2.25 6.0
24W5Q2B 24W5Q2P 1 1/2 1.50 3.25 4.50 1.500 0.500 0.656 1.44 1.920 5/8-11 5/8-11 x 2.75 6.0
32W5Q2B 32W5Q2P 2 2.00 4.00 5.25 2.000 0.620 0.781 1.69 2.411 3/4-10 3/4-10 x 3.00 6.0
40W5Q2B 40W5Q2P 2 1/2 2.50 5.00 6.88 2.500 0.620 0.906 1.94 2.911 7/8-9 7/8-9 x 3.50 6.0
48W5Q2B 48W5Q2P 3 3.00 6.00 8.50 3.000 0.620 1.156 2.44 3.540 1 1/8-7 1 1/8-7 x 4.50 6.0

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware kits are available for
O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M37 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd
4300 Catalog Hydraulic Flanges and Components

PQ – Stainless Steel
Block Plug
Code 61/62 Block Flange or Pad Plug
How To
Order

O-ring Face Flat Face

Specs
STANDARD
K Dynamic
TUBE FITTING FLANGE DRILL T MOUNTING Pressure
PART # SIZE A B DIA. L THREAD HARDWARE (x 1,000 PSI) Assembly /
O-RING FACE FLAT FACE (in.) (in.) (in.) (in.) (in.) UNC-2B SHCS SS Installation
CODE 61 BLOCK FLANGE OR PAD PLUG
8PQ1B 8PQ1P 0.50 1.500 2.120 0.344 1.20 5/16-18 5/16-18 x 2.00 5.0
12PQ1B 12PQ1P 0.75 1.750 2.620 0.406 1.20 3/8-16 3/8-16 x 2.00 5.0
16PQ1B 16PQ1P 1.00 2.000 2.820 0.406 1.45 3/8-16 3/8-16 x 2.25 5.0 Reference
20PQ1B 20PQ1P 1.25 2.500 3.190 0.469 1.45 7/16-14 7/16-14 x 2.25 4.0 Section
24PQ1B 24PQ1P 1.50 2.750 3.750 0.531 1.70 1/2-13 1/2-13 x 2.50 3.0
32PQ1B 32PQ1P 2.00 3.250 4.000 0.531 1.70 1/2-13 1/2-13 x 2.50 3.0
40PQ1B 40PQ1P 2.50 4.000 4.500 0.531 1.95 1/2-13 1/2-13 x 2.75 2.5
48PQ1B 48PQ1P 3.00 4.500 5.310 0.656 2.20 5/8-11 5/8-11 x 3.00 2.0
CODE 62 BLOCK FLANGE OR PAD PLUG
8PQ2B 8PQ2P 0.50 1.750 2.220 0.344 0.94 5/16-18 5/16-18 x 1.50 6.0
12PQ2B 12PQ2P 0.75 2.000 2.810 0.406 1.19 3/8-16 3/8-16 x 2.00 6.0
16PQ2B 16PQ2P 1.00 2.250 3.190 0.492 1.44 7/16-14 7/16-14 x 2.25 6.0
20PQ2B 20PQ2P 1.25 2.750 3.750 0.531 1.44 1/2-13 1/2-13 x 2.50 6.0
24PQ2B 24PQ2P 1.50 3.250 4.500 0.656 1.69 5/8-11 5/8-11 x 2.75 6.0
32PQ2B 32PQ2P 2.00 4.000 5.250 0.781 1.69 3/4-10 3/4-10 x 3.00 6.0
40PQ2B 40PQ2P 2.50 5.000 6.880 0.906 1.94 7/8-9 7/8-9 x 3.50 6.0
48PQ2B 48PQ2P 3.00 6.000 8.500 1.190 2.44 1 1/8-7 1 1/8-7 x 3.75 6.0

To receive mounting hardware with flange, insert a “K” after the material designator. Mounting hardware
kits are available for O-ring Face part numbers and include 4 bolts, 4 lock washers and an O-ring.

Dimensions and pressures for reference only, subject to change.

M38 Parker Hannifin Corporation

Tube Fittings Division
Columbus, Ohio
http://www.parker.com/tfd