SERIES 216.
10 SELF-PRIMING HORIZONTAL SCREW PUMP FOR LUBRICATING LIQUIDS
PRODUCTS
LUB OILS
HYDRAULIC OILS
CLEAN FUEL OILS
LABELLING
LUB OIL PUMPS
HYDRAULIC SYSTEMS
FUEL TRANSFER PUMPS
MEMBER OF THE COLFAX GROUP
HOUTTUIN B.V.
SERIES 216.10 GENERAL INFORMATION
Principle Products
The Houttuin double entry twin screw pumps Lubricating oils
series 216 are horizontal rotating self priming Hydraulic oils
positive displacement pumps. Two inter-mes- Clean fuel oils
hing screws rotating in a pump casing insert
ensure high pumping efficiency with constant Labelling
axial flow and unequalled suction power. Main lub oil pumps
Auxiliary lub oil pumps
Construction Hydraulic systems
The spindles are supported and axially held in Fuel oil transfer systems
position by ball bearings. The transmission of
torque from the driven spindle to the idler Performance data
3
spindle is effected by product lubricated Capacity Q up to 535 m /h
timing gears located in an attached gearbox. Viscosity range V 20 to 760 cSt
The ball bearings and timing gears maintain a Temperature of
o
small clearance between the screws, thus pumped liquid t up to 80 C
preventing metal to metal contact. Inlet pressure ps up to 6 bar
Outlet pressure pd up to 16 bar
Shaft sealing Difference
In standard design the pump is fitted with pressure ∆p up to 16 bar
single unbalanced mechanical seals, with Speed n up to 2900 rpm
fluid chamber if required. Flanges according to DIN or ANSI
Overload protection A preliminary pump selection can be effected
For protection against overload a built-on by means of the performance graphs. For the
spring loaded relief valve can be supplied. exact performance data as function of the
viscosity of the liquid to be pumped and the
Applications pump speed, please refer to the individual
For pumping lubricating oils, hydraulic oils or characteristics.
other lubricating fluids which do not contain
abrasive substances nor chemically attack the
pump materials. As lube oil pump in ship and
offshore engineering, as filling pumps in tank
farms and in hydraulic systems.
AVAILABLE MATERIALS FOR PUMP AND MECHANICAL SEALS:
Pump Mechanical seal according to DIN 24960 / API
Screw shafts Casing, casing insert and covers Seal faces Springs ‘O’ -rings
- Carbon Steel - Cast Iron - Chrome Steel - Stainless - Viton
- Nodular cast Iron against Steel
- Carbon (Type 300)
1
SERIES 216.10 PERFORMANCE GRAPHS
Flow rate/pressure at minimum and maximum viscosity according to pump size.
For exact performance data dependant of viscosity and rpm please refer to the individual
characteristics per pump size.
2
SERIES 216.10 CONSTRUCTION
Safe shaft sealing by single unbalanced
and product lubricated mechanical seals.
Safe transmission of torque through
hardened and ground oil lubricated
timing gears.
Amply dimensioned oil lubricated
and maintenance free ball bearings,
which additionally serve for the axial
location of the spindles.
For overload protection a direct
mounted pressure relief valve is optional.
The special profile of the spindle flanks
results in continuously and nearly
pulsation-free pumping, high efficiency,
good NPSH-values and constant
pressure course.
Axial forces balanced
ONLY SIZE 088 through double entry spindles
Rigid spindles of solid material therefore
compared with multi-part spindles
no crevice corrosion.
Heating of the pump foot is optional.
3
SERIES 216.10 DIMENSIONS
Discharge- and
suction flange
Shaftend
Possible arrangements
Sense of rotation:
clockwise seen from drive side
PUMPEN PUMP DIMENSIONS FLANGES PN 16 DIN 2533 RELIEF VALVE
SIZE SIZE
a b c e f m n s DN B C D
088 325 310 35 415 350 90 60 4x18 100 228 180 8x18 46
105 370 330 35 460 370 90 60 4x18 125 254 210 8x18 46
118 400 335 35 500 380 100 60 4x22 150 285 240 8x22 70
135 480 400 40 570 450 100 70 4x22 200 340 295 12x22 70
150 580 450 40 670 500 100 70 4x22 250 405 355 12x26 100
165 620 490 45 740 550 120 90 4x26 250 405 355 12x26 100
180 670 540 45 790 600 120 90 4x26 300 460 410 12x26 100
195 680 590 45 800 650 120 90 4x26 300 460 410 12x26 135
210 690 600 45 840 660 150 120 4x26 300 460 410 12x26 135
225 700 660 45 850 720 150 120 4x26 350 520 470 16x26 135
PUMP PUMP DIMENSIONS SHAFT END WEIGHT
SIZE KG (CA)
g h i j k o p p1 q d l t u
088 230 230 292,5 478 26 287 305 197,5 455 28 60 31 8 150
105 240 245 300 496 26 312 310 207,5 485 28 60 31 8 200
118 250 260 345 590 26 335 335 218 545 32 80 35 10 250
135 275 280 341 635 30 373 355 233 581 38 80 41 10 350
150 300 305 387 785 32 430 400 252,5 677 42 110 45 12 500
165 320 335 426 812 32 477 425 277,5 736 45 110 48,5 14 720
180 350 355 440 877 32 505 465 292 775 50 110 53,5 14 950
195 370 375 460 927 32 513 480 307 800 55 110 59 16 1050
210 390 395 525 979 32 535 520 321,5 870 60 140 64 18 1250
225 435 415 540 1025 36 545 540 336,5 890 65 140 69 18 1400
dimensions in mm, dimensions are subject to alternations.
4
SERIES 216.10 PERFORMANCE DIAGRAMS TOTAL PUMP PROGRAM*)
*) The diagrams show the performance range of the different pump series in our pump program and are for information only.
STANDARD PUMPS With Internal Bearings
for lubricating liquids
viscosity range : 20 - 760 cSt
: 98 - 3500 SSU
With External Bearings
for non-lubricating liquids
viscosity range : 0,6 - 1500 cSt
: 32 - 7000 SSU
NON-STANDARD PUMPS With Internal and
External Bearings
for lubricating and
non-lubricating liquids
viscosity range : 0,6 - 100.000 cSt
: 32 - 466.000 SSU
ENGINEERED PUMPS With Internal and
External Bearings
for lubricating and
non-lubricating liquids
viscosity range : 0,6 - 100.000 cSt
: 32 - 466.000 SSU
HOUTTUIN B.V.
Sophialaan 4, 3542 AR Utrecht
The Netherlands
P.O. Box 76, 3500 AB Utrecht
The Netherlands
Phone 31 - (0)30 - 2484611
Telefax 31 - (0)30 - 2411845
Telex 47280
Internet http://www.allweiler.de
MEMBER OF THE COLFAX GROUP
HOUTTUIN B.V.
04.03.216.10 E 5
