HISTORY INFORMATION FOR THE FOLLOWING MANUAL:

SERVICE MANUAL (COMMON)

GN1G CHASSIS
Segment: XM-H
Version Date Subject
1 3/2015 1st Issue.

LCD TV

9-888-168-01
For SM - Unique , please refer :
9-888-168-Ax
9 888 168 Ax ( America )
9-888-168-Cx ( China)
9-888-168-Ex ( Europe )
9-888-168-Px ( Pan Asia)
SERVICE MANUAL (COMMON)

GN1G CHASSIS
Segment: XM-H

LCD TV
MODEL LIST
THIS SERVICE MANUAL CONTAINS COMMON INFORMATION FOR BELOW REGIONS AND MODELS:

REGION
ASIA CHINA AMERICA EUROPE

MODEL
KDL 65W8*C
KDL-65W8*C KDL 75W8*C
KDL-75W8*C
 TABLE OF CONTENTS

Section Title Page Section Title Page

1. SAFETY NOTES 4. SERVICE ADJUSTMENTS

1-1. Warnings and Caution………………………………………………………. 5 4-1. Accessing Service Mode ..................................................................... 76
1-2. Caution Handling
g of LCD Panel ......…………….................................... 5 4 2.
4-2. Accessing Software Version................................................................ 76
1-3. Caution About the Lithium Batter………………………………………….. 6 4-3. Accessing Serial Number Edit…………………………………..……..... 77
1-4. Safety Check Out ........................……………......................................... 6 4-4. Accessing Model Number Setting…………………………………........ 78
1-5. Leakage Test .......................................................................................... 6 4-5. W/B Adjustment via Service Mode.…………………………................ 79
1-6. How to Find a Good Earth Ground………………………………………… 6 4-6. WB/Mura/CUC data transfer via Service Mode…………………........ 79
17
1-7. Lead Free Information….……………………………………………………
Information 7 4 7.
4-7. HDD Performance Check……………………....................................... 80
4-8. HDD Re-Register……………………………......................................... 80
1-8. Handling the Flexible Flat Cable (FFC)……………………………………. 7
4-9. Accessing Self Diagnostic Menu……………………………………….. 81
4-10. Summary of Service Control………………………………………........ 81
2. SELF DIAGNOSTIC FUNCTION
2-1. Overview of Control Buttons ................................................................... 8
2-2.
2 2 LED Display Control ………..................................................................... 9 5 DIAGRAMS
5.
2-3. LED Pattern………………........................................................................ 9 5-1. Circuit Board Location ......................................................................... 82
2-4. Standby LED Error Display…………………………………………………. 9
5-2. Block Diagram ………………………………………...................... 83
2-5. Triage Chart ............................................................................................ 10
5-3. Connector Diagram ………………………………………...................... 89
3 TROUBLE SHOOTING
3.
3-1. No Power…….……………………………………………………………….. 11
3-2. LED Blinking……………….………………………………………............... 18
3-3. No Sound……………………………......................................................... 30
3-4. No Picture................................................................................................. 42
35
3-5. Side Buttons Malfunction
Malfunction……………………………………………………. 66
3-6. IR Remote Commander Malfunction……………………………………… 68
3-7. Light Sensor Error…………………………………………………………. 70
3-8. Network Malfunction: Ethernet (Wired)……………………………………. 72
3-9. Wireless Network Malfunction……………………………………………. 73
3-10. Bluetooth Malfunction……………………………………………………….. 75
Please refer Service Manual – Unique for below information :
-Safety Warnings
-Wire Dressing
-Circuit
Ci it B Board
dLLocation
ti
-Disassembly and Exploded View.

4
 SECTION 1
SAFETY NOTES

1-1. Warnings and Caution 1-2. Caution Handling of LCD Panel

1) These servicing instructions are for use by qualified service personnel only. When repairing the LCD Panel, make sure you are grounded with a wrist band.
2) To reduce the risk of electric shock, do not perform any servicing other than When repairing the LCD Panel on the wall, the panel must be secured using the
that contained in the operating instructions unless you are qualified to do so. 4 mounting
ti h holes
l on ththe rear cover.
3) An isolation transformer should be used during any service to avoid 1) Do not press the panel or frame edge to avoid the risk of electric shock.
Possible shock hazard, because of live chassis. The chassis of this receiver is 2) Do not scratch or press on the panel with any sharp objects.
directly connected to the ac power line.
3) Do not leave the module in high temperature or in areas of high humidity for
4)) Be sure to follow
f these guidelines to protect your property and
an extended period of time.
avoid causing serious injury :
4) Do not expose the LCD panel to direct sunlight.
• Carry the TV with an adequate number of people; larger size TVs require
two or more people. 5) Avoid contact with water. It may cause short circuit within the module.
• Correct hand placement while carrying the TV is very important for 6) Di
Disconnectt the
th AC power when
h replacing
l i theth backlight
b kli ht (CCFL) or
safety and to avoid damages.
inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms)
5) Components identified by shading and ! mark on the exploded views,
7) Always clean the LCD panel with a soft cloth material.
and in the parts list are critical for safe operation. Replace these
components with Sony parts whose part numbers appear as shown in this 8) Use care when handling the wires or connectors of the inverter circuit.
manual or in supplements published by Sony. Circuit adjustments that are Damaging the wires may cause a short circuit.
critical for safe operation are identified in this manual. Follow these
9) Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).
procedures whenever critical components are replaced or improper
10) During the repair, DO NOT leave the Power On or Burn-in period for more
operation
p is suspected.
p
th
than 1 hour
h while
hil th
the TV iis fface d
down on a cloth.
l th

Figure 1. TV is faced down on a cloth during repair.

5
Safety Notes

1-3.
1 3. Caution About the Lithium Battery
1) Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type. 3) Measuring the voltage drop across a resistor by means of a VOM or battery
2) Outer case broken battery should not contact to water. operated AC voltmeter. The 'limit' indication is 0.75V so analog meters must
have an accurate low voltage scale. The SIMPSON'S 250 and SANWA SH-
1-4. Safety Check-Out
63TRD a
63 are
eeexamples
a p es o of pass
passive
e VOMs
O s that
a aaree su
suitable.
ab e Nearly
ea y aall ba
battery
ey
After correcting the original service problem, perform the following operated digital multimeter that have a 2 VAC range are suitable.
safety checks before releasing the set to the customer:- (see Figure 2.)
1) Check the area of your repair for unsoldered or poorly soldered
connections. Check the entire board surface for solder splashes and bridges.
2) Check
Ch k the
th inter
i t board
b d wiring
i i tot ensure that
th t no wires
i are pinched
i h d or
contact high-wattage resistors.
3)Check all control knobs, shields, covers, ground straps and mounting
hardware have been replaced. Be absolutely certain you have replaced all
the insulators.
4) Look for unauthorized replacement parts, particularly transistors that
were installed during a previous repair. Point them out to the customer and Figure 2. AC voltmeter to check AC leakage
recommend their replacement.
1-6. How to Find a Good Earth Ground
5) Look for parts which, though functioning show obvious signs of
1) A cold-water pipe is a guaranteed earth ground; the cover-plate retaining
deterioration. Point them out to the customer and recommend their
screw on most AC outlet boxes is also at earth ground
ground.
replacement.
2) If the retaining screw is to be used as your earth ground, verify that it is at
6) Check the line cords for cracks and abrasion. Recommend the
ground by measuring the resistance between it and a cold-water pipe with an
replacement of any such line cord to the customer.
ohmmeter. The reading should be zero ohms.
7) Check the antenna terminals, metal trim, metalized knobs, screws and all
3) If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble-
other exposed metal parts for AC leakage. Check leakage test as described
light (not a neon lamp) between the hot side of the receptacle and the
next.
retaining screw. Try both slots, if necessary, to locate the hot side on the line;
8. For safety reasons, repairing the Power board and/or Inverter board is
the lamp should light at normal brilliance if the screw is at ground potential
prohibited.
(see Figure 3).
1-5.Leakage Test
The AC leakage from any exposed metal part to earth ground and from all
exposed metal parts to any exposed metal part having a return to chassis must Figure 3. Checking for earth
not exceed 0.5mA (500 microamperes). ground.
Leakage current can be measured by any one of the three methods:-
1) A commercial leakage tester such as the SIMPSON 229 or RCA WT540A.
Follow the manufacturers instructions to use those instructions
instructions.
2) A battery-operated AC milliampmeter The DATA PRECISION 245 digital
multimeter is suitable for this job.
6
Safety Notes

1-7. Lead Free Information

The circuit boards used in these models have been processed using Lead Please hold reinforcement board and Please pull out FFC while pushing the
plunge it to depths. button of both ends at the same time.
Free Solder. The boards are identified by the LF logo located close to the
board designation. Main Board Main Board

Figure 4: LF Logo Figure 5: LF logo on circuit board

The servicing of these boards requires special precautions. It is strongly

recommended to use Lead Free Solder material in order to guarantee optimal
< Insertion> <Pull out>
quality of new solder joints.

1-8. Handling the FLEXIBLE FLAT CABLE (FFC)

 When you insert / pull out FFC, please grasp a reinforcement board and main
body of FFC.

Release Button
of Connector

FFC connector broken if pull out FFC

without press and hold both Release
Button of connector. Symptom 5X blinking
will be appear due to improperly seated.

7
Self Diagnostic Function

SECTION 2
SELF DIAGNOSTIC FUNCTION
2-1
2-1. Overview of Control Buttons
2-1-1.
FRONT TV CONTROLS/ TERMINALS/ INDICATOR

Remote Control Sensor /

Light sensor / * Illumination LED/ 3D
Sync Transmitter
Illumination lights up or blinks in different
colours
l according
di tto ththe status
t t off the
th TV
( details refer to 2-2. LED Display Control

REAR OF TV

Power
Turn the TV on or switch to standby mode
CH+/- (Channel) / / ,
+/- (Volume) / / .
Press to select the next or
previous channel.
Press to adjust the volume.
In TV Home Menu: buttons
will work as , , , .
INPUT SELECT /
TV SELECT/ CONFIRM
Press to Press to select the next or
display p
previous channel.
the TV Home In TV Home Menu: buttons
Menu. will work as (select/confirm)

8
 Self Diagnostic Function

2-2 LED Display Control

2-2. 2 4 Standby LED Error Display
2-4.
White Center Side Amber
Status
LED
Side RGB LED
LED
Remarks Smart
Core Detection Items Board Error Item
Power Off
*1 power switch off (by side RED LED
( by power saving switch off and Off Off Off
key) blinking
*1)
Power On White Off Off count
STBY/i.LINK STBY/PC STBY
Off Off Off Main 12V failure [MAIN_POWE]  G** Board Error
( by remote control off only ) 2x
Picture Off White looping White one shot Off * This failure is not saved  BMX Board Error
Device Connection White Cyan one shot Off Main 5.0V failure [DC_ALERT]  BMX Board Error
Power ON Animation White White one shot Off
Sleep Timer/On  BMX Board Error
Amber 3
3x Audio amp. protection [AUD_ERR]
Timer/Reminder/REC Timer/Photo *2 One Shot is only user  Speaker
White One shot -> Off
Frame action.
Lit*2 Tuner or demodulator I2C NACK [TU_DEMOD]  BMX Board Error
( Power On )
On Timer/Reminder/REC Timer After 5 minutes, side amber
Off Off Amber  Panel module
( Deep Standby ) LED On Panel ID EEPROM I2C NACK (Also panel power
The number of LED blinking  Tcon board
p ) [[P_ID_ERR]]
failure is a suspect)
Red indicates cause of failure  G** B
Board
d Error
E
Self Diagnosis Off Off (*detect at startup sequence only)
Blinking ( refer to Led Error / Triage  BMX Board Error
chart)
Blinking:0.5sec On / 0.5sec
5x  Tcon board
Aging mode White Green Blinking Off FRC device I2C No ACK [FRCTC_I2C]
Off
Software Updating white blinking white blinking off
FRC device Initialization failure [[FRCTC_I2C]
_ ]  Tcon board
Software Updating finish White Blue lit off
(*detect at startup sequence only)
Amber
Test Reset White white blinking
blinking
Green /Amber Blinking:0.5sec On / 0.5sec
 G** Board Error
Error of panel ID White Off 6x Backlight failure [BACKLIGHT]  Panel module
Blinking Off
Red(Pink)  BMX Board Error
REC (SCART REC & HDD *2 One Shot is only user
White One shot -> Off
REC/LIVE PAUSE) [AEP/J only] action
action. Over temperature protection [TEMP
[TEMP_ERR]
ERR]
Lit*2 7x  BMX Board Error
ePOP/
White Cyan loop Off
One shot Center White when Temp. sensor I2C NACK [TEMP_ERR]
Shop Illumination feature change

2-3. LED Pattern

When safety shutdown occurs, Standby LED display reports the cause by using the lightning
patterns as indicated below.

0.5sec 3.0sec 3.0sec

0.5sec Size G* Board Type
Example: The figure above shows LED display when SHUTDOWN is caused by Audio
Error. It repeats flashing for a specified number of times in 0.5sec/cycle and has a 3 seconds 65” GL1SB
interval of lighting off. Please note that a 3 seconds interval of lighting off is fixed regardless of abnormal state types. 75” GL1C

9
 Self Diagnostic Function

2-5. Triage Chart

Symptoms - Shutdown. Power LED No Video Smart Bluetooth
Remote Network Audio Skype
blinking red diagnostics sequences Power - missing or distorted Core (BT)
No White
Power
Smart Bluetooth /
Reference LED & Stationary No No
Wireless Core no One Step
does not coloured video video No Skype
2 3 4 5 6 7 8 9 10 can't No Audio LED (Set Remote
response lines or One of all Remote Can't Work
connect is still (OSR) can't
to remote dots Inputs Inputs
alive) connect
(Dead
Set)

BAX Board                
G* Board      
H* Board   

Speaker  
Wifi & BT
   
Module
LD Board  
LVDS FFC    
Tcon      
LCD Panel      

Panel Panel Soft-

Power Power LD (Tcon) (Backlight) TEMP ware Emitter
Problem FAN
Audio (N/A)
Local
I2C

Most likely defective part

Size B* Board G* Board H* Board
S
Secondary
d possible
ibl ddefective
f ti partt
65” BMX GL1SB HSC3_L
Not Applicable 75” BMX GL1C HSC3_L

10
Troubleshooting

3-1. NO POWER SECTION 3

3 1 1 NO POWER (XMH
3-1-1 (XMH-65)
65)
TROUBLESHOOTING
Size B* Board G* Board H* Board
NO POWER
65” BMX GL1SB HSC3_L
75” BMX GL1C HSC3_L

Check BL_ON No Voltage Main Board Problem

Check Fuse F6101 at Pin 3 of (B*)
Replace PSU
& FB801S , for open Connector
Yes CN6401

yes
no

Check +Out1 No Voltage

No Voltage Replace PSU
Check Stby and +Out2 at
3.3V at Pin 5 of Replace PSU CN5801
Connector CN6401

yes
yes

PSU OK Output Connector

Output Voltage
No Voltage Name CN6401

Check Power ON BL_ON 2.64V~3.3V Pin 3

Main Board Problem
at Pin 9
(B*)
Of connector CN6401 STBY3.3V 3.35V~3.55V Pin 5

yes AC OFF DET 3.45V Pin 7

BL_ERR 0V Pin 8

Power ON
Power_ON 2 64V~3 3V
2.64V~3.3V Pin 9

REG12V 12.2V~13.2V Pin 13Pin 18

Check Reg12V at
No Voltage Replace PSU
Pin 13Pin 18 of Output Connector
Output Voltage
Connector CN6401 Name CN5801

+OUT1 173.6V~250.3V Pin 1

yes
+OUT2 173.6V~250.3V Pin 2

11
Troubleshooting

3-1-2
3 1 2 NO POWER (XMH-75)
(XMH 75)
BL_ON active HIGH no
START Main Board Problem(B*)
(~3.3V)

AC Connect (80 ~ 288V yes

Case 4
yes
LED output check no BL Err level check
(133.4V~192.9V) (~2.8V)

Can TV power on?

yes
NO no
Power Supply
Y
Yes Working
W ki Normal
N l
Replace Power supply
F6101 Fuse OPEN check
(G*)

No Replace Power supply

((G*))
STBY output check NO Replace Power supply
(G*)
(3.35~3.55V)
Output Output Connector
Name Voltage CN6401
yes
Output
O t t Connector
C t
Output Voltage
BL_ON 2.64V~3.3V Pin 3 Name CN5801
Power ON input check no
Main Board Problem(B*) STBY3.3V 3.35V~3.55V Pin 5 +OUT1 133.4V ~ 192.9V Pin 1
(~3.3V)
AC OFF
3.45V Pin 7 OUT2
+OUT2 133.4V ~ 192.9V Pin 2
yes DET

BL_ERR 0V Pin 8 +OUT3 133.4V ~ 192.9V Pin 3

12V output check no Replace Power supply Power_ON 2.64V~3.3V Pin 9 +OUT4 133.4V ~ 192.9V Pin 4
(12.2~13.2V) (G*)
Pi
Pin
REG12V 12.2V~13.2V Note: Board Details refer Section 3
13Pin 18
yes main page.

12
Troubleshooting

3-1-3
3 1 3 No POWER - DC/DC converter check

START

no 1.05V LDO check

Check C9216 Voltage. no 3.3V DDCON check. Check C9207 is
it 1.05V? ((Change
g B* Board))
Is the voltage 3.3V?
33 ? (Change B* Board)

yes
yes

1 5V DDCON check
1.5V check. 1 8V DDCON check
1.8V h k
Check C9224 Voltage. no Check C9230 is no
(Change B* Board) it 1.8V? (Change B* Board)
Is the voltage 1.5V?

yes yes

Check 3.3V_MAIN
Check C9188 Voltage. no 5.0V DDCON check. no 3.3V_MAIN check
C9005 Voltage.
Is the voltage 5V? (Change B* Board) (Change B* Board)
Is the voltage 3.3V?

yes
yes

Check C9203 Voltage. no 1.0V DDCON check END

Is the voltage 1V? (Change B* Board) DDCON/LDO working normal

yes

Note: Board Details refer Section 3

main page.

13
BMX Board PWB (A side) Detail

3.3V
F9015 R9321

C9213

C9216

1.5V

F9016

C9224

C9222

5.0V
C9185
R9277

F9013

C9188
BMX Board PWB (A side) Detail

1.0V C9169

C9263

F9012

C9203

1.05V
#PIN4

C9207

C9206

F9014

1.8V
F9017

C9229

#PIN4 C9230
 BMX Board PWB (A side) Detail

3.3V_MAIN #PIN1

C9005

Q9002
2
Troubleshooting

3 1 4 NO POWER – Muffin Replacement (Main Device)

3-1-4.

Muffin
replacement flow

Data on eMMC
eMMC erase need to be erase
first before
changing Muffin
Muffin replacement

Product SW write

No
Recover? Board Issue

Yes

Muffin issue

17
Troubleshooting

3-2. LED BLINKING

3-2-1. LED Blinking: 2x (Main power Error)

BMX board (XM-H) only  G* Board

2-time blinking

Check +19.5V_SS
at pin 15/17 of CN9000 Yes
or JL9011 G* Board

on B* Board,
Voltage > 13.2V ?

No

B* Board

Note: Board Details refer Section 3

main page.

18
Troubleshooting

3-2-1. LED Blinking: 2x (Main power Error)

Troubleshooting References
Board Name Board PWB (A side) Detail

BMX
(CN9000)

CN9000

BMX
(JL9011)
JL9011

19
Troubleshooting

3-2-2. LED Blinking: 3x (DC Alert & Communication Error)

BMX board (XM-H)

AUDIO
3-time blinking
Check
DC_ALERT Speaker Impedance NG
Speaker
at SP Connector,
Check +5.0V_MAIN NG 8Ω±1.2Ω ?
F9013, IC9021
F9013 IC9021,
at L9015, 4.959V
etc (B* Board)
<Voltage<5.285V? OK

OK Check Audio
NG
+12 5V
+12.5V
G* Board
at pin 16/18 of CN9000
TUNER on the B* Board
Check I2C_A
/ I2C_D bus: NG OK
I2C bus dumping
Probe JL6010, JL6011 or Muffin
/ JL6021/JL6022 Check
+12.5V NG
F7751, IC7751
OK at Power Amp side
, etc (B* Board)
of F7751 on
th B* B
the Board
d

OK
IC7751, etc
(B* Board)

20
Troubleshooting

3-2-2. LED Blinking: 3x (DC Alert & Communication Error)

Troubleshooting References
Board Name Board PWB (A side) Detail

BMX
(L9015) L9015

BMX
(F9103)
F9103

BMX
(IC9021)
IC9021

21
Troubleshooting

3-2-2. LED Blinking: 3x (DC Alert & Communication Error)

Troubleshooting References

Board Name Board PWB (A side) Detail

BMX JL6010
(JL6010,
(JL6010
JL6011) JL6011

BMX
(JL6021)
JL6021

BMX
(JL6022)

JL6022

22
Troubleshooting

3-2-2. LED Blinking: 3x (DC Alert & Communication Error)

Troubleshooting References
Board Name Board PWB (A side) Detail

BMX
(CN9000)
CN9000

BMX
(F7751)
F7751

BMX
(IC7751)

IC7751

23
Troubleshooting

3-2-3. LED BLINKING 5x (Panel Communication Error) – a) 12.5V NG

5-times blinking

NG
Change Change
B* Board
B Panel (T-con)
(T con)
Check
PANEL_VCC 12.5V at NG
G* Board/LD
CN8400 Symptom
on the B* Board improvement
OK
B*Board
Symptom
Replace the Harness improve
Between G
G* /LD board Harness
and B* board Refer I2C Error
Checking in next slide

NG
Symptom
improve
Replace
LVDS Harness
the LVDS Harness

NG

Note: Board Details refer Section 3

main page.

24
Troubleshooting

3-2-3. LED BLINKING 5x (Panel Communication Error) – b) 12C Error

XM-H/A/DT
XM H/A/DT (BMX)
(BMX): CL8411
C 8411 &
5-times blinking
CL8412

PANEL ID Check OK INIT DONE

INIT_DONE OK I2C Communication
Check I2C (Data & CLK) Check I2C (Data & CLK) Check I2C (Data & CLK)
At CL At CL At CL

NG NG NG

I2C Error

Change B* Board B-Board NG

OK

NG

Change FFC FFC NG

OK
NG

Change FRC FRC NG

OK

25
Troubleshooting

BMX Probing Points – I2C Line Check

BMX (A-Side)

CL8411
(I2C_S_DATA) CL8412
(I2C_S_CLOCK)

26
Troubleshooting

3 2 4 LED BLINKING 6x (Backlight Error)

3-2-4.

6-times blinking

Check
Check harness/connection
Harness / Change Symptom
**JL9008 Voltage ≥ 1.9 V G*board to B*Board Harness
Connection harness Improvement
BL_ERR_DET or
on B*Board broken
LD board to B*Board No
improvement
Voltage < 1.8 V
Harness / G*Board
Connection OK or LD?

G* Board LD

Out1 & Out2 Check (LED_Output)

Visual Check LS Bar No
FFC Conductive Copper Suspect LS
Peel Off? Bar Broken
PSU OK
Yes

Change S
Symptom
t
Panel Improvement Panel
No
Improvement
Change Symptom
B* board B* Board
Improvement

**BMX: JL9008 BL_ERR_DET

Note: Board Details refer Section 3

main page.

27
Troubleshooting

3 2 4 LED BLINKING 6x (Backlight Error)

3-2-4.

BMX: B Side

JL9008

28
Troubleshooting

3-2-5. LED BLINKING 7x (Temperature Error)

7-time blinking

Setting
circumstance is OK? No Set to another
Temperature, location, etc.
Ventilation, etc.

Y
Yes
Change B* Board,
NG
and Aging a few Panel
hours

Symptom
improvement
Check I2C_C bus Yes Temp sensor
B* Board
communication OK? IC1401

No

I2C_C bus dumping or

Troubleshooting Reference Muffin check

Board Name Board PWB (A side) Detail

BMX
(IC1401)

IC1401

29
Troubleshooting

3 3 No Sound
3-3.

No Sound

“Audio System”
Check the UI
Change to
“Speakers” setting
TV Speakers
“TV Speakers”
In “AV Set-up”

“TV Speakers”
Symptom

Change the Speaker NG Replace i

improvement
t
No Sound: Audio
B* Board
Harness the B* Board

No Sound: Tuner
Symptom NG
improvement
No Sound: HDMI
Speaker Harness Speaker impedance
NG No problem
~ 8ohm (+-1.2ohm) ?

NG

Replace speaker

30
Troubleshooting

3-3-1. Main Board Power Off Checking (for Main SP Lch & Rch) for BMX board only

No Checking Item OK NG
1 Check fuse F7751 Fuse short p
Fuse open
2 Check connectivity audio Vcc to GND No short to GND Either 1 short to GND
C7862 – GND
C7864 – GND
C7866 – GND
3 Check connectivity audio +3.3V_MAIN to GND No short to GND Either 1 short to GND
(only for BMX board)
IC7751 (Pin5) at R7879 – GND
4 Check connectivity audio output to GND. No short to GND Either 1 of pin short to GND
CN7751
Pin 1 – GND
Pin 2 – GND
Pin 3 – GND
Pin 4 – GND
5 Check connectivity
connecti it a
audio
dio output
o tp t path Must
M st have
ha e good connection Open circuit.
circ it
(only for BMX board): (~0 Ω)
L7751 (near to IC side) – CN7751 Pin4
L7752 (near to IC side) – CN7751 Pin3
L7753 (near to IC side) – CN7751 Pin2
L7754 (near to IC side) – CN7751 Pin1

31
Troubleshooting

Troubleshooting Reference
BMX board Side A
R7876 R7878

R7877

R7879

F7751
IC7751

C7866
C7862

C7864
18 16

CN9000

L7754 L7753 L7752 L7751

C7769 C7768

C7767
C7770

1 2 3 4

CN7751

R f
Reference A

32
Troubleshooting

Troubleshooting Reference
BMX board Side A

5 24
8 23
IC775
1
19
13

R7739
R7736
R7739
R7738

R f
Reference B

33
Troubleshooting

3-3-2. Main Board Power On Checking (for Main SP Lch & Rch) for BMX board only

No Checking Item OK NG If  NG If  NG
1 Check Switching Freq = 384kHz or 768KHz No switching Go to next checking.
checking
IC7751 side-terminal of ±20KHz frequency at
L7751,L7752, Vrms = don’t care either one of the
L7753,L7754 CL

2 Check F7751 MainSP (

V(before fuse)) = 12.5V ± 0.5V No voltage.
g Check fuse broken? Change
g fuse ((5A).
)
(for BMX XM-H board V(after fuse) = 12.5V ± 0.5 V Check CN9000 Pin 16 Check power supply
only) &18 got 12.5V? board audio VCC.

3 Check F7751 MainSP V(before fuse) = 19.5V ± 0.5V No voltage. Check fuse broken? Change fuse (5A).
(f BMX XM-A,
(for XM A XM-AT
XM AT V( f fuse)
V(after f ) = 19.5V
19 V ± 0.5V
0 V Check
Ch k CN9000 Pi
Pin 16 Ch k power supply
Check l
and XM-DT only) &18 got 19.5V? board audio VCC.

4 Check IC7751 (Pin 5) at V(before R7879) = 3.3V ± 0.5V No voltage. Check +3.3V_MAIN
R7879 V(after R7879) = 3.3V
3 3V ± 0.5V
0 5V supply
supply.
(for BMX board only)
5 Check R7876, R7877, Vdc = 3.3V ± 0.3V Vdc < 0.8V R7877 NG, R7876, R7878 NG,
R7878 Check IC7751 Check IC1000

6 Check R7736, R7738, R7738 = 12.288MHz If no frequency at If sound source OK, but
R7739, and R7740 R7740 = 3.072MHz R7738, R7739, at R7736 = NG, Muffin IC
R7739 = 48KHz and R7740, (IC1000) NG.
R7736 = moving CLK Muffin IC
All Vp-p ≈ 3.3V (IC1000) NG.
If no frequency
at R7736 make
sure sound
source OK.

Note : Parts location refer BMX Board : Reference A and Reference B

B.

34
Troubleshooting

3-3-3. No Sound: HP / Lineout Only for BMX board only

No Sound
HP / Lineout only This is for Main SP got sound, but HP / Lineout no
sound
BMX Power On checking

GN1 Main Board Power On Checking

No Checking Item OK NG If  NG
1 Insert HP Jack. Check R7705 Vdc = 3.3V ± 0.3V Vdc = 0V or < 1V Check HP_DET line
(R7705 – for BMX)
got short to GND? If short to GND
replace board.
2 Check IC7701 Pin 5 Vdc = 3.3V ± 0.3V Vdc = 0V or < 1V Check X_AUDIO_ MUTE_ SPHP
(X_AUDIO_MUTE_ SPHP) (Pin 5) short to GND. If short to
GND replace board.

3 Check JL7701 and JL7702. Can see audio signal Cannot see audio signal Go to below item No. 4 for
(with audio signal input) waveform waveform checking
4 Check IC7701 p
pin 9 Vdc = 3.3V ± 0.3V No 3.3V supply.
pp y

5 Check R7707, R7708 Can see audio signal Cannot see audio signal Muffin IC (IC1000) NG
(with audio signal input) waveform waveform

35
Troubleshooting

3-3-3. No Sound: HP / Lineout Only for BMX board only

Troubleshooting Reference
BMX board Side A

R7707
R7708

1 14 R7705

IC7701
5
6 9
7 8

C7702

36
Troubleshooting

3-3-3. No Sound: HP / Lineout Only for BMX board only

Troubleshooting Reference
BMX board Side B

JL7701

JL7702

37
Troubleshooting

3-3-4. No Sound : Scart Out Audio (For Europe model) BMX board only

No Sound Thi is
This i for
f Main
M i SP gott sound,
d but
b t SCART outt no sound.
d
SCART out only Please check this condition in Digital RF mode

BMX Power On checking

GN1 Main Board Power On Checking

No Checking Item OK NG If  NG
1 Check CL7851 ,CL7852. Can see output audio signal Cannot see audio Go to checking
(with audio signal input – waveform signal waveform 3-3-2: NO SOUND:
Digital RF mode) Audio (Additional : For
Europe models only)
2 Check IC7851 pin3 Vdc = 3.3V ± 0.3V No 3.3V supply
3 Check C7854, C7855 Can see input audio signal Cannot see audio Muffin IC (IC1000) NG
(with audio signal input – waveform signal waveform
Digital RF mode)

38
Troubleshooting

Troubleshooting Reference
BMX board Side A

C7852 C7854

5
4
3

1
CL785 IC7851
1
6
7

10

CL785
C7855
2

39

39
Troubleshooting

3-3-5. NO SOUND: TUNER 3-3-6. NO SOUND: MHL

This troubleshooting is only for Analog No Sound

NG
Refer to
Check the picture MHL NO PICTURE
No Sound with normal
picture
OK

NO OK
Check Sound by other TV set
Only RF tuner input? No Sound Audio
which is same model

YES NG

Check Source equipment OK

Please refer Audio by Reference TV set
Check IC1000 ((SoC)) Change B*
B Board.
Board
troubleshooting (F example,
(For l SSamsung TV(UN46ES7000)
, Toshiba TV(42WL863), RB1 or RB2)

NG

Check the settings of

Source equipment

40
Troubleshooting

3-3-7 NO SOUND: HDMI1/2/3/4

3-3-7.

No Sound

NG

Check the picture Refer HDMI NO PICTURE

OK
DVI
Does this model have YES
Check the mode Connect Stereo minijack cable between Source and the TV
TV, and
Analog Audio In
of Source equipment Change “HDMI/DVI Audio Source” to Auto or Analog Audio In.
(Stereo minijack)?
No
HDMI Change the mode of Source equipment to HDMI

Analog Audio In
Does this model have YES
“HDMI/DVI Audio Source”
Analog Audio In Change “HDMI/DVI Audio Source” to Auto or HDMI Audio In
setting is?
(Stereo minijack)?

NO Auto or HDMI Audio

OK
Check Sound by other TV set
which is same model No Sound Audio

NG

OK
NO Check Source equipment
Is Distributor used ? by Reference TV set Change B* Board.
(For example, RB2, RB1)
YES
NG

Connect Source Check the settings of

equipment directly Source equipment

41
Troubleshooting

3-4. NO PICTURE

No Picture BL_ON (L or H):

XM-H/A/DT(BMX): IC9013 (Pin 4)
BL_ON：H
Check Smart Core Check Replace
NG Replace
p NG LCD Panel
G t Any
Got A Normal
N l No the LVDS FFC
Behavior BL_ON the B-Board (T-CON)
Display? No Harness
(5x Blinking) on the B* Board

BL_ON：L Symptom Symptom improvement

Yes Yes
improvement
Check Other 5x Blinking Backlight LVDS FFC
B-Board NG
Portion: Harness

Ext. Video Input -

No Picture

HDMI - No Picture

Tuner - No Picture

Note: Board Details refer Section 3

main page.

42
Troubleshooting

BMX (B-Side)
BMX Probing Points

JL8401
(PANEL_VCC)

43
Troubleshooting

BMX (A-Side)
BMX Probing Points

F8401
(+12V_REG)

44
Troubleshooting

BMX (A-Side)
BMX Probing Points

IC9013 (Pin 4)
(BL ON)
(BL_ON)

45
3-4-1. Video Analog Signal Path

46
Troubleshooting

3-4-2. FOR ANALOG TUNING: @ All destination except JP.

Notes:
For LA-ISDB(BR/AR) , LA-T2(COL) and TW only - Parts for IFOUT_N line: R6007, FB6002, C6008, R6327,
Analog Tuning C6301, R6301.
- Parts for IFOUT_P
IFOUT P line:
line R6008,
R6008 FB6003,
FB6003 C6009,
C6009 R6326,
R6326
C6300, R6300.
For Other
destination Confirm ANT or Cable connection - Parts for IFAGC line: R6072, R6009, R6010, R6069,
C6302, R6303.

NG
Channel can be lock?

OK

Noisy Check part mounting condition NG

Pi t
Picture quality
lit iis noisy?
i ? for analog control line
“IFOUT_N, IFOUT_P, IFAGC”

Not Noisy
OK

OK Please re-upgrade Firmware NG

(PKG), Check again Picture
quality?
q y

Done (End) Change B* board

Note: Board Details refer Section 3

main page.

47
Troubleshooting
BMX BOARD (A Side)

R6008 FB6003 C6009 R6072 R6009

R6010

R6326 C6300 R6300

R6007 FB6002 C6008

R6327 C6301 R6301

48
Troubleshooting

BMX BOARD (A Side)

R6303

C6302

R6069

49
Troubleshooting

3-4-3.FOR
3 4 3.FOR DIGITAL TUNING 1: @ TW and LA-ATSC(MX/UC).
LA ATSC(MX/UC).
Notes:
Digital Tuning 1 - Parts for IFOUT_N line: R6007, FB6002, C6008,
For TW only R6327, C6301, R6301.
- Parts for IFOUT_P
IFOUT P line: R6008,
R6008 FB6003,
FB6003 C6009,
C6009
Confirm ANT R6326, C6300, R6300.
For LA-ATSC(MX/UC) only
or Cable connection
- Parts for IFAGC line: R6072, R6009, R6010, R6069,
C6302, R6303.
- Parts for I2C_A_SDA line: R6001, C6004.
OK Check part mounting NG
condition for - Parts for I2C_A_SCL line: R6002, C6005.
Channel can be lock?
digital control line
“I2C_A_SDA,I2C_A_SCL”
NG
OK
OK
Sound is normal?

No sound

Confirm UEC of digital If UEC = 0

Check IC1000 (SoC)
RF by Service mode

If UEC > 0

Check part mounting condition for digital data line NG

“IFOUT_N, IFOUT_P, IFAGC”

OK

Please re-upgrade NG
Firmware (PKG), Check
again Picture quality?
OK

Change B* board
Done (End)
50
 Troubleshooting

BMX BOARD (A Side)

R6008 FB6003 C6009 C6004 R6001 R6072 R6009

R6010

R6326 C6300 R6300

R6007 FB6002 C6008 C6005 R6002

R6327 C6301 R6301

51
Troubleshooting

BMX BOARD (A Side)

R6303

C6302

R6069

52
 Troubleshooting

3-4-4.FOR DIGITAL TUNING 2: @ AEP-T2S2, JP, PA_T2, CH/HK, LA-ISDB(BR/AR) and LA-T2(COL).

Digital Tuning 2
For LA-ISDB(BR) and Notes:
LA-T2(COL) only For AEP-T2S2 and
JP only - Parts for I2C_A_SDA line: R6001,
C6004.
Confirm ANT or For PA_T2 and
CH/HK only
l Confirm ANT or Satellite connection - Parts for I2C_A_SCL
I2C A SCL line: R6002,
R6002
Cable connection C6005.
- Parts for TU1_TS_DATA0 line: R6015,
R6321.
NG Check part mounting condition for - Parts for TU1_TS_CLK line: R6016,
Channel can be lock? digital control line OK R6322.
“I2C_A_SDA,I2C_A_SCL”

OK
OK NG
Sound is normal?

No sound

If UEC = 0
Confirm UEC of digital RF by Service mode Check IC1000 (SoC)

If UEC > 0

NG
Check part mounting condition for digital data line
“TU1_TS_DATA0, TU1_TS_CLK”

OK

Please re-upgrade NG
Firmware (PKG), Check
again Picture quality?

OK

Done (End) Change B* board

53
Troubleshooting
C6004 R6001

BMX BOARD (A Side)

R6002

C6005

R6016 R6015

54
Troubleshooting

BMX BOARD (A Side)

R6321

R6322

55
Troubleshooting

3-4-5
3 4 5. NO PICTURE: HDMI1

No Picture

Check the below point at All

lines
Connector side
Other Input is OK are Replace
Check other ・Check +5V line
NG CN5401
HDMI input ・Check HPD line
・Check DDC lines
Only +5V ・Check TMDS lines
All Inputs line NG
are NG is NG +5V line is OK
Other TV set S
Spec:4.7~5.
47 5
Check Picture by other TV set OK Replace and HPD line
3V Only TMDS
Replace is NG lines
which is same model IC1000
R5427 Spec:2.4~5.3V are NG
Target board & other
TV sett both
b th NG
Only DDC Replace
Connect Source linesare NG RB5405,RB5406,
Is Distributor used ? RB5407,RB5408
YES equipment directly
NO
Replace
Check Source equipment R5424,R5425
by Reference TV set Change B* Board
Reference TV Replace IC1000 (SoC)
(For example, RB1) NG NG
Set OK

Reference
TV set
NG

Check the settings of

Source equipment
56
Troubleshooting

CN5401
BMX A side
BMX-A RB5405,RB5406,
RB5405 RB5406
RB5407,RB5408 R5424
HDMI1
R5425
R5427

57
 Troubleshooting

3-4-6. NO PICTURE: HDMI2

No Picture

Check the below point at All lines

Connector side are NG
Replace
Check other Other Input is OK ・Check +5V line
CN5600
HDMI input ・Check HPD line
Check DDC lines
・Check

All ・Check TMDS lines

Only +5V line NG
Inputs
is NG
are +5V line is OK
NG Other TV set Spec:4.7~5.3V
Check Picture by other TV set OK Replace and HPD line
Only TMDS lines
Replace is NG
which is same model IC1000 are NG
R5606 Spec:2.4~5.3V
Target board
& other TV set
Only DDC lines
both NG Replace
Connect Source are NG RB5603,RB5604,
Is Distributor used ? RB5609,RB5610
YES equipment directly
NO
Replace
Check Source equipment R5615,R5616
by Reference TV set Change B* Board.
(For example, RB1) Reference TV Set Replace IC1000 (SoC).
NG NG
OK

Reference TV set
NG

Check the settings of

Source equipment

58
Troubleshooting

IC1000
BMX A side
BMX-A
HDMI2
R5606
RB5603,RB5604,
R5616 RB5609,RB5610
R5615
CN5601
59
 Troubleshooting

3-4-7. NO PICTURE: HDMI3

No Picture

Check the below point at All lines

Connector side are NG

Replace
Check other Other Input is OK ・Check +5V line
CN5601
HDMI input ・Check HPD line
・Check DDC lines

All Inputs Only +5V line ・Check TMDS lines

NG
are NG is NG
Spec:4.7~5.3V +5V line is OK
Other TV set
and HPD line
Check Picture by other TV set OK Replace Only TMDS
Replace is NG lines are NG
which is same model IC1000
R5611 Spec:2.4~5.3V
Target board & Only DDC
other TV set lines
both NG Replace
are NG RB5605,RB5606,RB5600,
Connect Source
Is Distributor used ? RB5601
YES equipment directly
NO
Replace
Check Source equipment R5602,R5603
by Reference TV set Change B* Board.
Reference Replace IC1000 (SoC).
(For example, RB1) NG NG
TV Set OK

Reference TV
set
NG

Check the settings of

Source equipment
60
Troubleshooting

BMX A side
BMX-A IC1000

HDMI3
R5611

R5602
RB5605, RB5606
RB5605 RB5606,
R5603 RB5600,RB5601
CN5601
61
 Troubleshooting

3-4-8. NO PICTURE: HDMI4

No Picture

Check the below point at All

lines
Connector side
Other Input is OK are Replace
Check other ・Check +5V line NG
CN5602
HDMI input ・Check HPD line
・Check DDC lines

All Inputs Only +5V line ・Check TMDS lines

NG
are NG is NG
Spec:4.7~5.3V +5V line is OK
Other TV set
and HPD line
Check Picture by other TV set OK Replace Only TMDS
Replace is NG lines
which is same model IC1000
R5614 Spec:2.4~5.3V are NG
Target board & Only DDC
other TV set lines
both NG Replace
are NG RB5607,RB5608,RB5612,
Connect Source
Is Distributor used ? RB5613
YES equipment directly
NO
Replace
Check Source equipment R5607,R5608
by Reference TV set Change B-Board.
Reference TV Set Replace IC1000 (SoC).
(For example, RB1) NG NG
OK

Reference TV
set
NG

Check the settings of

Source equipment
62
Troubleshooting

BMX A side
BMX-A IC1000

HDMI4
R5614

R5608
RB5607, RB5608
RB5607 RB5608,
R5607 RB5612, RB5613
CN5602
63
Troubleshooting

3-4-9. NO PICTURE: MHL (BMX)

No Picture

Check voltage at High

MHL sense, NG ((No communications))
R5445 Check HDMI
HDMI_0_HPD_CBUS
0 HPD CBUS Replace IC1000 (SoC)
(SoC).

Spec:High:2.0~5.3V at connector side And inform the designer of it

Low:0.8~2.0V
NG (No
OK
Low communications) Replace
Check TMDS(D0
TMDS(D0+/D0-)
/D0 ) lines
at connector side R5443, R5444

OK

Check Source equipment

by Reference TV set
Low (< 2V)
(For example, Samsung TV(UN46ES7000)
Check DDCCLK, , Toshiba TV(42WL863), RB1, RB2) OK
Check R5409 (47k ) NG
at R5424 (Open)

High Replace NG
OK
R5409
Check HDMI picture
in this input

D5404 NG NG
(Open) OK
Change
MHL cable Replace
D5404

Replace IC1000 (SoC). Check the settings of Inform the designer Check “NO PICTURE
And inform the designer of it Source equipment of it – HDMI” flow
64
Troubleshooting

R5424
BMX A side
BMX-A
R5443

R5444

R5445

65
Troubleshooting

3-5. SIDE BUTTONS MALFUNCTION

OK
Side Key button Change Switch Unit Switch unit issue
malfunction

NG

OK
Harness on Switch Unit Harness
and B* Board properly connected connection
issue

NG

OK
Change
Switch unit-B* board Harness Harness issue

NG
NG
NG NG
Power Key (B*Board)
Key AD(B*Board)
Check parts value :
Parts Broken issue Check parts value :
0 ohm < R1089 < 2 ohm?
0 ohm < R1085 < 2 ohm?
OK OK
OK OK
Power Key Muffin Pin (B*Board) Key AD muffin pin (B*Board)
Check voltage(Power ON condition) : Muffin IC1000
Check voltage (Power ON condition):
3.287V < Voltage < 3.55V? problem
1.53V < voltage < 1.89V?

NG NG

Change B*Board

66
Troubleshooting

BMX > A‐SIDE

Voltage check Power Key Muffin

Pin

Voltage check Key AD muffin

Pin

R1089 R1085

67
Troubleshooting

3-6. IR REMOTE COMMANDER MALFUNCTION

Center white LED lit up OK Check whether center OK Remote control battery
IR do not response to white LED blink ,when using
when remote control is could be weak.
Remote Commander pressed commander near the sensor
windows Change battery.

NG

Harness on H-board Harness

OK
and B*
B Board connection
properly connected issue
NG
OK
Change H-B* board harness
H-B* board Harness issue

NG

OK
Change Smart Core Smart core issue

NG NG
B*Board NG NG B*Board
Check parts value : Check parts value :
Parts Broken issue
0 ohm < R1062 < 2 ohm 95 ohm < R1124 < 105 ohm

OK
OK
IR Muffin Pin (B
(B*Board)
Board) OK
Check voltage (Power ON condition): Muffin IC1000
3.287V < Voltage < 3.55V? problem

NG

Change B*Board

68
 Voltage check IR Muffin Pin

BMX > A-SIDE

R1124

R1062

69
Troubleshooting

3-7. Light Sensor Error

Backlight doesn’t change

Check UI setting for light Change the UI setting OK User did not activate light
when ambient lighting to “ON”
ON
Sensor Make sure it is “on”
Sensor. on” sensor function
f ti
level changed
NG

Harness on H-board and OK Harness connection

B* Board properly connected issue

NG

OK
Ch
Change H B* board harness
H-B
H-B* board Harness issue

NG
OK
Change Smart Core Smart Core issue

NG
B*Board NG
Check parts value : Part broken issue
0 ohm < R1061 < 2 ohm

OK

Opt_sens Muffin Pin OK

Check voltage changing from Muffin IC1000 problem
room light to dark condition
NG

Change B*Board

70
 Voltage
g check Opt
p _Sensor
Muffin Pin

BMX > A-SIDE

R1061
Troubleshooting

3-8.Network Malfunction: Ethernet (Wired)

[Network Set-up]
Set up]
>[Wired Set-up]
on the TV

OK Connection Results OK Connection Results OK

Connection Results
B board
Cable Connection Local Access Internet Access

Failed Failed Failed

OK Wired Set-up Auto Check Local router Proxy setting
Check cable B board
IP address
dd setting
tti DHCP server
NG Manual

Ethernet Cable Check IP address

& Local router setting

72
Troubleshooting

3-9. Wireless Network malfunction (a)

1) Internal Wireless Network malfunction

Wireless Network
on the TV

No
Error Message appear Is the radio field No
when the Wireless Strength too weak B* Board
Network is selected? or even No signal?

Yes Yes
NG
*1 Hardware defect suspected.
Change WiFi module Access Point
Go to the next page

OK

WiFi module

73
Troubleshooting

3-9. Wireless Network malfunction (b)

*1 From previous page

Check harness connection NG OK

is OK between WiFi and Connect properly Loose harness
B* board
B

OK NG

NG
NG Change harness
Change between B* board Change B* board
Wi-Fi module and WiFi

OK
OK If Wi-Fi
Wi Fi malfunction
lf ti happens,
h
• Wi-Fi module
• Harness between WiFi and B* Board
Wi-Fi module Main Harness
• B* board
are suspected.

Note: Board Details refer Section 3

main page.

74
Troubleshooting

3-10.Bluetooth malfunction

Touch pad Remote doesn’t

doesn t work
Or
3D-glasses (Active) doesn’t work
Or
Bluetooth Speaker/Headphone/Headset doesn’t work

Please refer
Touch pad Remote manual
Home > Settings > OK Check BT antenna OK 3D-glasses (Active) manual
Bluetooth Settings Can read Connection is OK Or
Bluetooth Speaker/Headphone/Headset operation manual
NG Near discoverable NG
else
Bluetooth Device
OK Loose BT antenna
Connect properly connection
NG

Check harness NG OK
connection is OK C
Connect
t properly
l Loose harness
between BT &
Change B* board
NG
OK
NG Change harness NG
Ch
Change BT module
d l Between Change Change B*
B board
B* board and BT
OK OK

BT module Main Harness

75
 SECTION 4
SERVICE ADJUSTMENTS
4-1. Accessing Service Mode
4-2. Accessing Software Version
1) Go to TV standby condition by remote commander.
1) In Service Mode, select “Model Information “ Press (Enter) or button
2) Press “i+ (info)”, “5”, “Volume +” then “TV power” on remote.
on Remote to enter status information.
3) You can see Service Mode on display.
Service Mode Model

4 TV Power Model Information >> Status Information >>

Service Mode Self diagnosis History >> Model Information >>
Video / Audio >> Model Number Setting >>
Panel / PQ >> SERIAL NUMBER EDIT
Model Information >> General Setting >>
Tuner >>
Self diagnosis History >>
1 (i+) Remote Commander
Wifi / BT >>
Video / Audio >> SDB Service Menu >>

Panel / PQ >>
[</>] Set [Home]Exit [</>] Set [Home]Exit
General Setting >>
Tuner >>
2 (5)
Wifi / BT >> Main Micro
Main Micro
SDB Service Menu >> SW Version: PKG0.451.001
3 NVM Version: 0000000
Boot Version:  v1.000
PQ Version: 261000006
[</>] Set [Home]Exit Screen Sample AQ Version: AQ0.0028
<Ext>
exFRC: 60.00.01.00
60 00 01 00
Remote Commander
Service Mode Screen Sample CameraVID: 0
CameraPIC: 0
CameraFW: 0

2) Press (Enter) or “Return”

Return button on Remote to back to Service Mode
Mode.

Service Mode

Model Information >>

Self diagnosis History >>
Video / Audio >>
Panel / PQ >>
General Setting >>
Tuner >>
Wifi / BT >>
Remote Commander
SDB Service Menu >>

[</>] Set [Home]Exit

Service Mode Screen Sample

76
Service Adjustment

4-3. Accessing Serial Number Edit

1) In Service Mode, select “Model” pressing button. Select “Serial Number
Edit” pressing button.

S i M
Service Mode
d

Model Information >>

Self diagnosis History >>
Video / Audio >>
Panel / PQ >>
General Setting >>
Tuner >>
Wifi / BT >>
SDB Service Menu >>
Remote Commander
Screen Sample
[</>] Set [Home]Exit
Note: * The font color of YES is change to black when it is selected.
Screen Sample
4) If YES is
i selected,
l t d the
th iinputt d
data
t iis saved
d iinto
t EEPROM
EEPROM.
SERIAL NUMBER EDIT is grayed out and the serial number that has
2) Press or button to select number
been input is displayed.
. * The font color of YES is change to black when it is selected. User will not able to edit anymore.

Remote Commander

3) Serial Number can be set ONLY ONCE.

After user input data , press <Enter>.
Pop dialog will appear to inform user to confirm data. Screen Sample

Press or button to select YES or NO. Note : * The font color of SERIAL NUMBER is change to orange
Select YES if input data is correct.
correct after YES is selected.
selected
Select NO if input data is incorrect.
Press <Enter> to save answer.
77
Service Adjustment

4-4. Accessing Model Number Setting

5) If NO is selected, the input data is not saved into EEPROM. 1) In Service Mode, select “Model” pressing button. Select “Model Number
The serial number that has been input is displayed. Setting” pressing button.
User can still edit the Serial Number.
Service Mode Model

Model Information >> Status Information >>

Self diagnosis History >> Model Information >>
Video / Audio >> Model Number Setting >>
Panel / PQ >> SERIAL NUMBER EDIT
General Setting >>
Tuner >>
Wifi / BT >>
SDB Service Menu >>
Remote Commander

[</>] Set [Home]Exit [</>] Set [Home]Exit

[MODEL_NUMBER_SETTING]

____________
Screen Sample
p
Note : * The font color of NO is change to black when it is Screen Sample
selected.
OK

2) Press or button on Remote to input numbers.

3) Press or arrow key to Product Name Candidate.
(e.g. KDL-40X500B CO1, KDL-40X500C BR6)
4) Select one Product Name from the LIST, press (Enter) will pop dialog
to inform user to confirm data.
Screen Sample 5) Press “OK” button to select YES or No.
Select OK if input data is correct.
Note : * The font color of SERIAL NUMBER is white after NO is selected.
selected
Select NO if input data is incorrect.
Press <Enter> to save answer.
Model dependent settings will be overwritten into EEPROM.
78
Service Adjustment

4-5. W/B Adjustment via Service Mode 4-6. WB/Mura/CUC data transfer via Service Mode
Apply when B* board or Panel is replaced. Apply when B* board or Panel is replaced.
1) In “Service Mode, select “Panel/PQ” pressing button. 1) In “Service Mode, select “Panel/PQ” pressing button. Screen Sample

Screen Sample

2) Go to “WB Adjustment”,
Adjustment” category by or button To select
button. 2) Go to “WB/Mura/CUC
WB/Mura/CUC data transfer
transfer” ”,, category by or button. To
“WB Adjustment”, press button. select “WB/Mura/CUC data transfer”, press button.
3) To change data, press or button.
4) In “WB/Mura/CUC data transfer:
a) Select “WB/Gamma data transfer” by pressing       or        on remote 
commander until cursor is on “WB/Gamma data transfer”.
/
Selectable items are:
 0. SoC to T-con
 1. T-con to SoC
Screen Sample  2. No Action
b) To change the items, press or on remote commander.
c) Select “[start]” and press “Enter” button to start transfer.
3) To change data, press or button.

Screen Sample
Screen Sample

79
Service Adjustment

4-7. HDD Performance Check 4-8. HDD Re-Register

1) In “Service Mode, select “General Setting” pressing button. 1) In “Service Mode, select “General Setting” pressing button.

Screen Sample Screen Sample

2) Select “HDD Performance check” by pressing button. 2) Select “HDD Re-Register” by pressing button.

Screen Sample
Screen Sample

3) A message "Please wait ..." is displayed during performance check

processing. 3) Result OK or NG will be displayed after HDD re-registration is
succeed/failed
4) Result OK or NG will be displayed after performance of HDD is checked

Screen Sample

80
 Error Naming

49 A
4-9. Accessing
i S
Self
lf Diagnostic
Di ti Menu
M
Go to Self diagnosis history through Service Mode
1) Go to TV standby condition by remote commander.
2) Press “i+ (info)”, “5”, “Volume +” then “TV power” on remote.
Error
3) Select “Self
Self diagnosis history”
history by pressing “→”
→ button C
Count
4) You can see Self Check.
Smart Core
Red LED
Service Mode blinking count
Error Error Error
timestamp timestamp timestamp
Model Information >> for last for second for 3rd
last l t
last
Self diagnosis History >> recorded
d d
error recorded recorded
Video / Audio >> error error
Panel / PQ >>
General Setting >>
Tuner >>
Wifi / BT >>
SDB Service Menu >>

[</>] Set [Home]Exit

OR
1) Go tto TV standby
G t db condition
diti by
b remote t commander.
d Self Diagnosis Display
2) Press “i+ (info)”, “5”, “Volume -” then “TV power” on remote. •Panel Operation Time is recorded every
3) You can see Self Check. 30 min, but Total Operation Time is recorded
4) To Exit – Press Power Off & On. Total Operation Time [hr] – Boot Count – Panel Operation Time [hr] every 1 hr. Therefore, the panel op. time might
become larger than the total op. time.
4 10 Summary of Service Control
4-10. F
Format t off error timestamps
ti t
YYMMDDhhmmss (in UTC)
Function The flow of control Example:
Service mode on <Test>+<TV>/<Display><5><
<Test>+<TV>/<Display><5><Vol
Vol Up><Power> 150823132523 -> Aug 23 2015 13:25:23 UTC
* Only when time is set, an error timestamp
Service mode off <MENU>/<HOME> is saved.
Panel operation time clear
Item up / down <↑>/ <↓>
<7> -> <0>
Execute (実⾏) <OK>

81
Diagrams
SECTION 5
DIAGRAMS

5-1.CIRCUIT BOARD LOCATION

5-1-1. 65” 5-1-2. 75”

BMX BOARD
GL1SB GL1C BMX BOARD
BOARD SWITCH BOARD
UNIT

SWITCH UNIT
** SMART CORE BLOCK ** SMART CORE BLOCK

<** SMART CORE BLOCK >

HSC3_L
MOUNT

WLAN/BT
MODULE(11N)

82
Diagrams

5-2. Block Diagram

5-2-1. XM-H model (AEP based)
LED WIFI &
Bluetooth
Key O tS
OptSens Si
Sircs
BMX GPIO GPIO SIRCS GPIO GPIO USB2.0

DDR3 Muffin USB2.0

USB1
2.5GB (4Gb×5) ARM Cortex A12 dual
core
USB2.0
Cortex-A12 NEON USB2 / HDD
eMMC X-Reality Pro
16GB Multi-format Decoder. USB2.0
3D OpenGL ES3.0, DX11 USB3
u-Con. DRAM Controller
LVDS
LVDS USB×4 HDMI 4
HDMI×4
120H
120Hz
FRC+Tcon /60Hz HDMI 1.4a, MHL2.0 GPIO
(120Hz) LVDS/V-by-One HDMI 1.4
TCON, HDMI
Local Dimming / MHL2.0
XM-H: Active 3D SPDIF
Video Processor
Audio Processor
2D/3D Converter
DEMOD(ATSC,DVB-T/C) I2S Audio
ADC/DAC P-AMP SP
Ethernet MAC+PHY AMP BD28620
2ch
HP
L/R
IF TS Out

CI/CI
CI/CI+ Eth
Ether

83
Diagrams

5-2. Block Diagram

5-2-2. XM-H model (BR,AR,LA_ISDB)

LED WIFI &

Bluetooth
Key OptSens Sircs
BMX GPIO GPIO SIRCS GPIO GPIO USB2.0

DDR3 Muffin USB2.0

USB1
2.5GB (4Gb×5)
ARM Cortex A12 dual
core USB2.0
USB2 /
eMMC Cortex-A12 NEON
HDD
16GB X-Realityy Pro
Multi-format Decoder.
3D OpenGL ES3.0, DX11
LVDS u-Con. DRAM Controller
120Hz /60Hz LVDS USB×4
FRC+Tcon HDMI×4
(120Hz) HDMI 1.4a, MHL2.0
LVDS/V-by-One HDMI 1.4
HDMI / MHL2.0
MHL2 0
TCON,
XM-H: Active 3D SPDIF Local Dimming
Video Processor
Audio Processor
2D/3D Converter I2S Audio
DEMOD(ATSC,DVB-T/C)
P
P-AMP
AMP SP
ADC/DAC AMP BD28620 2ch
Ethernet MAC+PHY
HP
S-mini L/R
Out
IF TS

Ether

84
Diagrams

5-2. Block Diagram

5-2-3. XM-H model (PA,CH)

LED WIFI &

Bluetooth
Key OptSens Sircs
BMX GPIO GPIO SIRCS GPIO GPIO USB2.0

DDR3 Muffin USB2.0

USB1
2.5GB (4Gb×5) ARM Cortex A12 dual core
Cortex-A12 NEON USB2.0
eMMC X-Reality Pro USB2 /
16GB Multi-format Decoder. HDD
3D OpenGL ES3.0, DX11
DRAM Controller
LVDS u-Con. USB×4
120Hz /60Hz LVDS HDMI 1.4a, MHL2.0
FRC+Tcon HDMI×4
(120Hz) LVDS/V-by-One
TCON, HDMI 1.4
PC HDM / MHL2.0
Audio Local Dimming I
XM-H: Active 3D SPDIF Video Processor
in
XM-A (3D): Active Audio Processor
3D 2D/3D Converter
XM-A (2D): None 3D DEMOD(ATSC,DVB-T/C) I2S Audio
ADC/DAC P-AMP SP
Ethernet MAC+PHY AMP
BD28620 2ch

HP
S-mini L/R
Out
IF TS

Ether

85
Diagrams

5-2. Block Diagram

5-2-4. XM-H model (HK,TW)

LED WIFI &

Bluetooth
Key OptSens Sircs
BMX GPIO GPIO SIRCS GPIO GPIO USB2.0

DDR3 Muffin USB2.0

USB1
2.5GB (4Gb×5)
ARM Cortex A12 dual core USB2.0
Cortex-A12 NEON USB2 / HDD
eMMC
X-Reality
X Reality Pro
16GB
Multi-format Decoder.
3D OpenGL ES3.0, DX11
DRAM Controller
LVDS u-Con.
USB×4
120Hz LVDS HDMI 1.4a, MHL2.0
FRC+Tcon /60Hz HDMI×4
(120Hz) LVDS/V-by-One
y
TCON, HDMI 1.4
PC HDMI
Local Dimming / MHL2.0
Audio
XM-H: Active 3D SPDIF Video Processor
in
Audio Processor
2D/3D Converter
DEMOD(ATSC,DVB-T/C)
( )
ADC/DAC I2S
Audio
Ethernet MAC+PHY P-AMP SP
AMP BD28620
2ch
HP
L/R O
Outt
IF TS

Ether

86
Diagrams

5-2. Block Diagram

5-2-5 XM-H model (JP)

LED WIFI &

Bluetooth
Key OptSens Sircs
BMX GPIO GPIO SIRCS GPIO GPIO USB2.0

DDR3 Muffin USB2.0

USB1
2.5GB
2 5GB (4Gb×5) ARM Cortex A12 dual
core USB2.0
Cortex-A12 NEON USB2 / HDD
eMMC X-Reality Pro
16GB Multi-format Decoder.
3D OpenGL ES3.0, DX11
DRAM Controller
LVDS u-Con.
C
USB×4
120Hz LVDS HDMI 1.4a, MHL2.0
FRC+Tcon /60Hz HDMI×4
(120Hz) LVDS/V-by-One
TCON, HDMI 1.4
HDMI
Local Dimming / MHL2.0
XM-H:
XM H: Active 3D SPDIF Video Processor
Audio Processor
2D/3D Converter
DEMOD(ATSC,DVB-T/C)
I2S Audio
ADC/DAC
Ethernet MAC+PHY P-AMP SP
AMP BD28620
2ch
HP
S-mini L/R Out
RS232 IF SIRCS
TS

C4 Sircs in Ether

87
Diagrams

5-2. Block Diagram

5-2-6 XM-H model (UC)

LED WIFI &

Bluetooth
Key OptSens Sircs
BMX GPIO GPIO SIRCS GPIO GPIO USB2.0

Muffin USB2.0
USB2 0
DDR3 USB1
2.5GB (4Gb×5)
ARM Cortex A12 dual USB2.0
core USB2 / HDD
eMMC Cortex-A12 NEON
16GB X-Reality Pro
Multi-format Decoder.
3D OpenGL ES3.0, DX11
LVDS u-Con. DRAM Controller
120Hz LVDS USB×4
FRC+Tcon /60Hz HDMI×4
HDMI 1.4a, MHL2.0
(120Hz) LVDS/V-by-One HDMI 1.4
TCON
TCON, HDMI
Local Dimming / MHL2.0
XM-H: Active 3D SPDIF Video Processor
Audio Processor
2D/3D Converter
DEMOD(ATSC,DVB-T/C)
I2S
ADC/DAC Audio
Ethernet MAC+PHY P-AMP SP
AMP BD28620
2ch

HP
S-mini L/R
RS232 IF SIRCS Out
TS

C4 Sircs in Ether

88
 Diagrams

5-3-1. 65”

SM
M CN203 T-Con Board
1-7988-511-11 HUS_POWER_KKEY 3 18 BMX Board
HUS_KEY_AD 2 16
HUS_GND 1 17 CN8400 AUO: JAE FT-RTE51SZ-HF
Header : 1-821-143-11 Housing: 1-821-117-11 SPI_CS 1 51 SPI_CS
JAM SYT10-3W WL SYT10-03HG FRC_RST 2 50 FRC_RST
Terminal: 1-821-116-11 SPI_CK 3 49 SPI_CK
710112-2MAC NC 4 48 (3D_EN) no need to connect to B board
SPI_DO 5 47 SPI_DI To Tcon flash
CN1000 LUT_SEL/SPI_DI 6 46 SPI_DO From Tcon flash
1 1 WIFI_GND SA_MODE 7 45 Aging
2 2 WIFI_BT_RSTT LVDS_SEL 8 44 (SPI_ENB) no need to connect to B board
GN1 Smart Core 3 3 WIFI_WAKEUUP BINT/WP 9 43 WP
4 4 BT_WAKEUP 3D_SYNC 10 42 3D_SYNC
5 5 WIFI_GND SDA 11 41 SDA
Main Harnness 6 6 WIFI_STBY_3.3V SCL 12 40 SCL
5-3. Connector Diagram

CN101 7 7 WIFI_STBY_3.3V PANEL_DET 13 39 GND

HSCC3-L STBY3.3V 1 23 8 8 WIFI_STBY_3.3V BIN[4]P 14 38 CH2_4+
5V_MAIN 2 20 9 9 WIFI_GND BIN[4]N 15 37 CH2_4-
GND 3 25 11 10 BT_3D_LR BIN[3]P 16 36 CH2_3+
A-2066-086-A LED_AMBER 4 22 10 11 WIFI_GND BIN[3]N 17 35 CH2_3-
LED_PWM_W 5 24 USB 14 12 WIFI_USB_M GND 18 34 GND
LED_PWM_R 6 30 13 13 WIFI_GND BCLK+ 19 33 CH2_CLK+
LED_PWM_B 7 28 15 14 WIFI_USB_P BCLK- 20 32 CH2_CLK-
LED_PWM_G 8 26 12 15 WIFI_GND GND 21
51pin FFC 31 GND
GND 9 27 2 16 HUS_KEY_ADD BIN[2]P 22 30 CH2_2+
MAIN_3.3V 10 29 1 17 HUS_GND BIN[2]N 23 29 CH2_2-
OPT_SENSE 11 19 3 18 HUS_POWER__KEY BIN[1]P 24 28 CH2_1+
SIRCS 12 21 11 19 SC_OPT_SENSE BIN[1]N 25 27 CH2_1-
Header: 1-821-139-11 Housing: 1-821-126-11 2 20 5V_MAIN BIN[0]P 26 26 CH2_0+
JAM SYT10-12WWS SYT10-12HG 12 21 SC_SIRCS BIN[0]N 27 25 CH2_0-
Terminal: 1-821-116-11 4 22 SC_LED_AMBBER GND 28 24 GND
710112-2MAC 1 23 SC_STBY_3.33V AIN[4]P 29 23 CH1_4+
5 24 SC_LED_PWM M_W AIN[4]N 30 22 CH1_4-
3 25 SC_GND AIN[3]P 31 21 CH1_3+
8 26 SC_LED_PWM M_G AIN[3]N 32 20 CH1_3-
9 27 SC_GND GND 33 19 GND
7 28 SC_LED_PWM M_B ACLK+ 34 18 CH1_CLK+
USB CABLE 10 29 SC_MAIN_3.33V ACLK- 35 17 CH1_CLK-
GND 1 1 #30 6 30 SC_LED_PWM M_R GND 36 16 GND
Wifi/BT RST_L 2 2 #30 Housing: Header: 1-820-162-12 AIN[2]P 37 15 CH1_2+
WOW_L 3 3 #30 AIN[2]N 38 14 CH1_2-
WOBT_L 4 4 #30 Terminal: AIN[1]P 39 13 CH1_1+
GND 5 5 #28 AIN[1]N 40 12 CH1_1-
VCC 6 6 #28 AIN[0]P 41 11 CH1_0+
VCC 7 7 #28 AIN[0]N 42 10 CH1_0-
VCC 8 8 #28 GND 43 9 GND
GND 9 9 #28 GND 44 8 GND
GND 10 11 #28 CN7751 GND 45 7 GND
VSYNC 11 10 RED#28 1 1 MAIN L+ NC 46 6 N.C.
GND 12 15 Shield 2 2 MAIN L- PANEL_VCC 47 5 VDD
GND 13 13 BLK#28 1 3 MAIN R+ PANEL_VCC 48 4 VDD
DM 14 12 WHT#28 2 4 MAIN R- PANEL_VCC 49 3 VDD
DP 15 14 GRN#28 Housing: 1-842-593-11 Header: 1-842-566-12 PANEL_VCC 50 2 VDD
Header: 1-819-332-11 Housing: 1-819-502-11 JST PBVP-04V-S JST SM04B-PBVSS-TB(LF)(SN) PANEL_VCC 51 1 VDD
JST SM15B-GHSS-TB(LF)(SN) GHR-15V-S Terminal: 1-819-513-11 Header: 1-843-107-11
Terminal: 1-819-512-11 SPHD-001T-P0.5
SSHL-002T-P0.2

CN9000
Faston #187 5 30 STBY+3v3
SPK Harnness
SPEAKERR L+ 1 1 NC 29 +3.3V_STBY__S
Front L- 2 2 3 28 BL_ON/ICSPCCLK
Lch Faston #110 4 27 VLED_REF/PW
WM_DIMMER/TM_SCL
NC 26 +3.3V_STBY__B/19.5_ON
6 25 PWM_4/BLINKING/SPI0_MOSI
Faston #187 NC 24 DC_SENSE
SPEAKERR R+ 1 3 8 23 BL_ERR
Front R- 2 4 9 22 POWER_ON/IISCPDAT
Rch Faston #110 10 21 GND
11 20 GND
12 19 GND
13 18 REG12/19.5V__AU
14 17 REG12V/19.5__SS
15 16 REG12V/19.5__AU
16 15 REG12V/19.5__SS
oard CN6401 17 14 REG12V
GL1S
G BoSB Board (CN2) NC 1 NC 18 13 REG12V
DC_DIMMER 2 4 19 12 GND
BL_ON 3 28 20 11 GND
PWM_DIMMER 4 27 NC 10 VPP_PIC
STBY3.3V 5 30 21 9 GND
BLINKING 6 25 NC 8 TCON_ON/TM M_LOG_RX
AC_OFF_DET 7 1 NC 7 PANEL_PWR__DET/TM_LOG_TX
BL_ERR 8 23 NC 6 LD_MODE_SW W/SA_MODE
POWER_ON 9 22 NC 5 PWM_5/SPI0__SCK
GND 10 21 2 4 IP_REF/DC_DDIMMER/TM_SDA
GND 11 20 NC 3 PWM_3/TM_EEMIT
GND 12 19 NC 2 PWM_2/SPI0__nCS
REG12V 13 18 7 1 AC_OFF_DETT
REG12V 14 17 Housing: Header: 1-843-953-11
REG12V 15 16
REG12V 16 15 Terminal:
REG12V 17 14
REG12V 18 13
GND 19 12
GND 20 11
GND 21 9
GND 22 NC
GND 23 NC
NC 24 NC
NC 25 NC
NC 26 NC
NC 27 NC
NC 28 NC
Header: 1-842-551-11 Housing:

Terminal:

CN6801
(CN3) +OUT1 1
+OUT2 2
LS
NC 3
NC 4
Header: 1-822-359-11 Housing:

Terminal:

CN6802
-OUT1 1
(CN4) -OUT2 2
LS
NC 3
NC 4
NC 5
Header: 1-822-360-11 Housing:

Terminal:

CN6101
(CN1) AC-N 1
AC-L 2
AC pigtail
Header: 1-822-908-11 Housing:

Terminal:
89
 SM
Diagrams

CN203 T-Con Board

1-798-511-11 HUS_POWER_KEY 3 18 BMX Boarrd
5-3-2. 75”

HUS_KEY_AD 2 16
HUS_GND 1 17 CN8400 SDC：JAE FI-RXE51S-HF
Header : 1-821-143-11 Housing: 1-821-117-11 SPI_CS 1 51 SPI_CS
JAM SYT10-3WL SYT10-03HG FRC_RST 2 50 FRC_RST
Terminal: 1-821-116-11 SPI_CK 3 49 SPI_CK
710112-2MAC NC 4 48 (3D_EN) no need to connect to B bboard
SPI_DO 5 47 SPI_DI To Tcon flash
CN1000 LUT_SEL/SPI_DI 6 46 SPI_DO From Tcon flash
1 1 WIFI_GND SA_MODE 7 45 Aging
2 2 WIFI_BT_RST LVDS_SEL 8 44 (SPI_ENB) no need to connect to B bboard
GN1 Smart CCore 3 3 WIFI_WAKEUP BINT/WP 9 43 WP
4 4 BT_WAKEUP 3D_SYNC 10 42 3D_SYNC
5 5 WIFI_GND SDA 11 41 SDA
Main Harness 6 6 WIFI_STBY_3.3V SCL 12 40 SCL
CN101 7 7 WIFI_STBY_3.3V PANEL_DET 13 39 GND
HSC3-L STBY3.3V 1 23 8 8 WIFI_STBY_3.3V BIN[4]P 14 38 CH2_4+
5-3. Connector Diagram

5V_MAIN 2 20 9 9 WIFI_GND BIN[4]N 15 37 CH2_4-

GND 3 25 11 10 BT_3D_LR BIN[3]P 16 36 CH2_3+
A-2066-086-A LED_AMBER 4 22 10 11 WIFI_GND BIN[3]N 17 35 CH2_3-
LED_PWM_W 5 24 USB 14 12 WIFI_USB_M GND 18 34 GND
LED_PWM_R 6 30 13 13 WIFI_GND BCLK+ 19 33 CH2_CLK+
LED_PWM_B 7 28 15 14 WIFI_USB_P BCLK- 20 32 CH2_CLK-
LED_PWM_G 8 26 12 15 WIFI_GND GND 21
51pin FFC 31 GND
GND 9 27 2 16 HUS_KEY_AD BIN[2]P 22 30 CH2_2+
MAIN_3.3V 100 29 1 17 HUS_GND BIN[2]N 23 29 CH2_2-
OPT_SENSE 111 19 3 18 HUS_POWER_KEY BIN[1]P 24 28 CH2_1+
SIRCS 122 21 11 19 SC_OPT_SENSE BIN[1]N 25 27 CH2_1-
Header: 1-821-139-11 Housing: 1-821-126-11 2 20 5V_MAIN BIN[0]P 26 26 CH2_0+
JAM SYT10-12WS SYT10-12HG 12 21 SC_SIRCS BIN[0]N 27 25 CH2_0-
Terminal: 1-821-116-11 4 22 SC_LED_AMBER GND 28 24 GND
710112-2MAC 1 23 SC_STBY_3.3V AIN[4]P 29 23 CH1_4+
5 24 SC_LED_PWM_W AIN[4]N 30 22 CH1_4-
3 25 SC_GND AIN[3]P 31 21 CH1_3+
8 26 SC_LED_PWM_G AIN[3]N 32 20 CH1_3-
9 27 SC_GND GND 33 19 GND
7 28 SC_LED_PWM_B ACLK+ 34 18 CH1_CLK+
USB CABLE 10 29 SC_MAIN_3.3V ACLK- 35 17 CH1_CLK-
GND 1 1 #30 6 30 SC_LED_PWM_R GND 36 16 GND
Wifi/BT RST_L 2 2 #30 Hoousing: Header: 1-820-162-12 AIN[2]P 37 15 CH1_2+
WOW_L 3 3 #30 AIN[2]N 38 14 CH1_2-
WOBT_L 4 4 #30 Teerminal: AIN[1]P 39 13 CH1_1+
GND 5 5 #28 AIN[1]N 40 12 CH1_1-
VCC 6 6 #28 AIN[0]P 41 11 CH1_0+
VCC 7 7 #28 AIN[0]N 42 10 CH1_0-
VCC 8 8 #28 GND 43 9 GND
GND 9 9 #28 GND 44 8 GND
GND 100 11 #28 CN7751 GND 45 7 GND
VSYNC 111 10 RED#28 1 1 MAIN L+ NC 46 6 N.C.
GND 122 15 Shield 2 2 MAIN L- PANEL_VCC 47 5 VDD
GND 133 13 BLK#28 1 3 MAIN R+ PANEL_VCC 48 4 VDD
DM 144 12 WHT#28 2 4 MAIN R- PANEL_VCC 49 3 VDD
DP 155 14 GRN#28 Hoousing: 1-842-593-11 Header: 1-842-566-12 PANEL_VCC 50 2 VDD
Header: 1-819-332-11 Housing: 1-819-502-11 JST PBVP-04V-S JST SM04B-PBVSS-TTB(LF)(SN) PANEL_VCC 51 1 VDD
JST SM15B-GHS-TB(LF)(SN)) GHR-15V-S Teerminal: 1-819-513-11 Heaader: 1-843-107-11
Terminal: 1-819-512-11 SPHD-001T-P0.5
SSHL-002T-P0.2

CN9000
Faston #187 5 30 STBY+3v3
SPK Harness
SPEAKER L+ 1 1 NC 29 +3.3V_STBY_S
Front L- 2 2 3 28 BL_ON/ICSPCLK
Lch Faston #110 4 27 VLED_REF/PWM_DI MMER/TM_SCL
NC 26 +3.3V_STBY_B/19. 5_ON
6 25 PWM_4/BLINKING/SSPI0_MOSI
Faston #187 NC 24 DC_SENSE
SPEAKER R+ 1 3 8 23 BL_ERR
Front R- 2 4 9 22 POWER_ON/ISCPDAAT
Rch Faston #110 10 21 GND
11 20 GND
12 19 GND
13 18 REG12/19.5V_AU
14 17 REG12V/19.5_SS
15 16 REG12V/19.5_AU
16 15 REG12V/19.5_SS
G Board CN6401 17 14 REG12V
GL1C Board (CN2) NC 1 NC 18 13 REG12V
DC_DIMMER 2 4 19 12 GND
BL_ON 3 28 20 11 GND
PWM_DIMMER 4 27 NC 10 VPP_PIC
STBY3.3V 5 30 21 9 GND
BLINKING 6 25 NC 8 TCON_ON/TM_LOGG_RX
AC_OFF_DET 7 1 NC 7 PANEL_PWR_DET/TTM_LOG_TX
BL_ERR 8 23 NC 6 LD_MODE_SW/SA_MMODE
POWER_ON 9 22 NC 5 PWM_5/SPI0_SCK
GND 100 21 2 4 IP_REF/DC_DIMMERR/TM_SDA
GND 111 20 NC 3 PWM_3/TM_EMIT
GND 122 19 NC 2 PWM_2/SPI0_nCS
REG12V 133 18 7 1 AC_OFF_DET
REG12V 144 17 Hoousing: Header: 1-843-953-11
REG12V 155 16
REG12V 166 15 Teerminal:
REG12V 177 14
REG12V 188 13
GND 199 12
GND 200 11
GND 211 9
GND 222 NC
GND 233 NC
NC 244 NC
NC 255 NC
NC 266 NC
NC 277 NC
NC 288 NC
Header: 1-842-551-11 Housing:

Terminal:

CN6801
(CN3) +OUT1 1
+OUT2 2
LS
+OUT3 3
+OUT4 4
Header: 1-822-359-11 Housing:

Terminal:

CN6802
-OUT1 1
(CN4) -OUT2 2
LS
-OUT3 3
-OUT4 4
NC 5
Header: 1-822-360-11 Housing:

Terminal:

CN6101
(CN1) AC-N 1
AC-L 2
AC pigtail
Header: 1-822-908-11 Housing:

Terminal:
90
 English
Sony EMCS (Malaysia) Sdn. Bhd.
9-888-168-01 © 2015.03
RDCM
91