Scribd
Upload
1K views

Physics Atp 0625 Notes: To Produce More Accurate or Reliable Results

This document contains notes on physics experiments and measurements. It lists variables that should be kept constant in experiments, such as temperature and volume. It also describes ways to increase accuracy, such as repeating experiments, avoiding parallax errors, and using insulation. Measurement tools like micrometers and verniers are explained. Sources of error are discussed for various experiments and graphs, and precautions are provided for electrical circuits and lens experiments.

Uploaded by

Aman Vithlani
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
1K views

Physics Atp 0625 Notes: To Produce More Accurate or Reliable Results

This document contains notes on physics experiments and measurements. It lists variables that should be kept constant in experiments, such as temperature and volume. It also describes ways to increase accuracy, such as repeating experiments, avoiding parallax errors, and using insulation. Measurement tools like micrometers and verniers are explained. Sources of error are discussed for various experiments and graphs, and precautions are provided for electrical circuits and lens experiments.

Uploaded by

Aman Vithlani
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 11

PHYSICS ATP 0625 NOTES

To produce more accurate or reliable


results:
• Repeat experiment, to calculate average reading.
• Avoiding parallax error, look perpendicular to the ruler.
• If accuracy in measurement was asked, check for zero
error.

Improvements that could be done to the


experiment (temp. cooling):
• Same initial temperature.
• Same volume of water.
• Same shape of beaker.
• Beakers of same surface.
• Same room temperature.
• Stirring the water in the beakers.
• Same time intervals.
• Same surface area. (Unless given different containers)
• Adding water or cooling effect at regular intervals.

Heat loss could be reduced by:


• Insulation of beaker.
• Covering beaker with a lid.

For 2 values to be directly proportional,


• The graph of the values must be a straight line from the
origin.
• As value 1 increase, value 2 increases.

For images produced from lenses on


screens, precautions taken:
• Use of a darkened room for the experiment.
• Avoiding parallax error in measurement, and look
perpendicular to the ruler.
• Object and lens at the same height from bench.
• Object/lens/screen is perpendicular to the bench.

To draw an image created from lens:


• Inverted from the original object.
• Sides are multiplied by the magnification.
*If values have difference by 0.1 or 0.01, that is the limit of
experimental accuracy, so answers are about the same.

For spring extension experiment,


variables that should be constant in the
experiment:
• Number of coils.
• Diameter of spring.
• Selection of loads.
• Mass of spring.

http://www.opamp-electronics.com/tutorials/experiments_ch_003.htm

micrometer : can measure the thickness of any small thing to


0.01 mm

vernier : can measure the inner and outer wall of anything to


1.05mm

Minimizing heating effect of a current:


• Lower current
• Increase voltage
• Add a lamp
• Increase resistance of a resistor

Adjustments made to experiments will be made to increase


accuracy

To increase accuracy of ray diagrams


• View bases of pins since pins may not be vertical
• Keep pins further apart
• Use more pins
• Avoid parallax, explain action and reason
• Repeats and average
Improvement made to experiments
about heating effect and insulation
• Lids
• Repeats
• Stirring
• Record max. Temperature
• Add insulation
• Keep constant room temperature
• Avoid heat loss

How to check if a rule is vertical:


• Protractor
• Use of set square
• Plumb line
• Spirit Level

Precautions taken in experiments about


formation of images by a lens
• Use a darkened area
• Meter ruler on bench or clamped
• Object and lens same height on bench
• Mark on lens holder to show center of lens
• Take more readings
• Avoid parallax error, explain action and reason
• Lens\screen perpendicular to bench

Variables in experiments about springs


and stretching effect:
• Number of coils
• Length of spring
• Diameter\thickness of spring or wire
• Range of loads
• Length of wire
• Coil spacing

Periodic time (T) is measured by timing a number (n) of


oscillations, then divide the time taken for all the oscillations
by the number of oscillations (n)

Drawing graphs:
• Label axis
• Choose a proper scale
• Well judged best fit line
• Thin and neat lines

Measuring the gradient:


• Draw a triangle on graph
• Use clear lines
• Triangle must be larger than half the line

Sources of error in calculating


circumference by string method:
• Parallax
• Diagonal winding
• Thickness of string

Improvement made to calculating


circumference by string method:
• Avoid parallax error
• Repeats and average
• Thinner string
• Parallel winding of springs
Precautions for circuit readings of I and
V so that accurate:
•For I specifically:
•Limit current so that temp. doesn't increase
•Use a tapping meter
•For I and V: Switch off between readings.

Fair test for pendulum experiments:


•Length of pendulum
•Shape of bob
•No. of swings
•Amplitude
Precautions and procedures in electrical
experiments:
•Check for a zero error
•Tap the meter to avoid sticking
•Initially choose the highest range for the
ammeter/voltmeter, then reduce the range for the ammeter
so that the deflection is almost full scale
•Always check polarities before closing the switch
(completing the circuit)
•Always check that connections are clean.
•Switch off the current when not making a measurement.
•When measuring resistance use low currents/voltages to
avoid heating and changing the resistance you are measuring

Why angle “I” is NOT equal to angle


“r” in ray experiment:
•Thickness of pins
•Thickness of mirror
•Protractor is not precise

Inaccuracy of ray box method:


 Thickness of rays.

Inaccuracy of pin method:


 Pins not straight,
 Too close,
 Thickness of lines drawn

Measuring 10 oscillations rather than 1:


•Reduce human errors
•Give more accurate value of time taken (T)
•Gives an average of T

NOTE:

Not the best list, but I tried and I hope this helps you!
THANKS FOR VIEWING!

THANK YOU!
Created and edited by:

SHAHID KARIM

You might also like