16 Port PoE Switch
16 Port PoE Switch
Board diagram
Model: CP-TNW-HP16G2F1-20
Front board
The 16 ports PoE switch is an unmanaged PoE Ethernet switch along with 16 * 100Base-TX
downlink PoE ports and 2 * 1000Base-TX uplink Ethernet ports featuring 30-watt 802.3at
PoE Output Uplink Gigabit
PoE+ as well as 1 additional Gigabit Combo port. The total PoE power budget is up to 180 LED Ports
watts. It supports real-time PoE output LED display.The device can be widely used in video
security monitoring systems, network projects, etc.
Application
Uplink Gigabit
PoE Output CCTV Mode PoE Output Ports SFP Combo Port
16 Percentage LED
Por
ts P
oE
Sw
itch
LC
D
dis
pla
y Back board
背面板
C
at
5/
AC100~240V
5e
/6
PoE camera
N
VR
Fi
be
r
PoE camera sw
itc
h
PoE camera Grounding Terminal
PoE camera
Notice
1) Device must be connected with lightning protection grounding; otherwise protection level will be greatly
Feature reduced; please use above No.20 wire to connect the grounding terminal;
2) The device requires rebooting after the dial switch has been utilized.
Provide 16x 100Mbps downlink PoE Ethernet ports, 2x gigabit uplink Ethernet ports and
1x gigabit Fiber port; Installation steps
Downlink Ethernet ports support PoE+, each port supports max. 30W output; Please check the following items before installation, if it is missing, please contact the dealer.
16 Ports PoE Switch 1pcs
Support power consumption indication(LED indicates power output status);
AC Power Cable 1pcs
Accord with IEEE802.3、IEEE802.3u、IEEE802.3ab、IEEE802.3 af/at standard; Accessories 1pcs
4K MAC address,2.75Mb cache; User Manual 1pcs
Quick installation, easy operation, convenient for wall-mounted、 desktop and rack
installations. Please follow installation steps as below:
1 ) Turn off the power of all the related devices before the installation; otherwise the device would be
※ Notice damaged;
2 ) Use Ethernet cable connect PoE IP camera and 1~16 downlink ports of product respectively;
The transmission distance depends on the signal source and cable quality; standard Cat5e/6 3 ) Use an Ethernet cable to connect equipment uplink port with NVR or computer;
Ethernet cable is strongly suggested for reaching the maximum transmission distance! Every 4 ) Connect power adapter;
100 mtr each power port drop will be approx 3 to 5 watts. After 250 mtr available POE power 5 ) Check if the installation is correct, equipment is in good condition, the connection is stable, then
will be approx. 15W to 20W at each IPC side. power on for system.
1 2
16 Port PoE Switch 16 Port PoE Switch
Specification
连接接口 连接接口
Trouble shooting
连接接口
If any trouble in installation, please follow these steps:
Item Description Please make sure you have followed the instruction to install the device;
Product Type Product Type 16ports Please confirm if the RJ45 cable order is in accordance with the EIA/TIA568A or 568B industry standards;
Downlink Ethernet Ports 16×10/100Base-TX PoE+ The power supply of each PoE port is no more than 30W; please do not connect the PoE device which
Uplink Ethernet Ports 2 × 10/100/1000Base-T+1 × 1000Base-X(combo) exceeds the maximum PoE power supply;
Port
Description Power Input 1×AC Female Terminal
Please replace a failure device with a proper one to check if the device is broken;
Grounding Terminal 1×Grounding Terminal
Power Input Mains on load,100～240VAC 50/ 60Hz RJ 45 Making Method
PoE Power Supply End-span(1/ 2，3/6),IEEE802. 3 af/at
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should conform with
PoE&Power PoE Max. Power Output 180W
EIA/TIA568A or 568B.
Single Port Power Output&
Voltage
Single Port PoE Power Output≤30W, Voltage 54VDC 1) Shuck off about 2cm long the insulating layer, and bare the 4 pairs UTP cable;
1. Downlink ports only communicate with uplink ports; 2) Depart the 4 pairs UTP cable and straighten them;
2. Restrain network storm under 2Mbps; 3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
One-key CCTV CCTV Mode 3.Extend transmission distance to 250m; ※
4.Rate:10Mbps(Downlink Ports) 4) Cut out 1.5 cm cable wrap and leave the bare wire;
Network Standard IEEE 802.3,IEEE 802.3u,IEEE 802.3ab, IEEE 802. 3z 5) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
Transmission Distance 100m(Max.) 6) Then use wire crimper to crimp it;
Exchange Capacity 7 . 2Gbps 7) Follow the 5 steps above to make the another end, following the same sequence of the first plug;
Network
Parameters Packet Transfer Rate 5.36Mpps 8) Using network tester to test the cable whether is working.
MAC Address 4K
Packet Data Cache 2.75Mb Pin Color Pin Color
Power Input 1x Red LED 1 white/green 1 white/orange
Link:16x Green LED 2 green 2 orange
Downlink Ethernet Ports
PoE:16x Yellow LED
Indicators 3 white/orange 3 white/green
Status Uplink Ethernet Port Link 2x Green LED
4 blue 4 blue
5x LED(Including 3x Green, 1x Yellow, 1x Red), separately indicate
PoE Power Output Percent 5 5
30%、60%、9 0%、95 %～100% white/blue white/blue
Protection ESD 6KV / 8KV, Per:IEC61000 - 4 - 2 6 orange 6 green
Level Surge Protection 6KV, Per:IEC61000- 4- 5 7 white/brown 7 white/brown
Operation Temperature - 10℃～45℃ 8 brown 8 brown
Operation
Storage Temperature - 40℃～85℃
Environment
Humidity(Non-condensing) 0～95%
EIA/TIA 568A EIA/TIA 568B
Dimensions(LxWxH) 442 mm * 285 mm * 44. 5 mm
Mechanics Material Iron Notice
Color Black When choose RJ-45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
When choose RJ-45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Product specifications subject to change without prior notice.
3 4
