SFP-OC48-IR2-GT

SFP OC-48/STM-16 Intermediate-Reach 1550nm Cisco Compatible M

The GigaTech Products SFP-OC48-IR2-GT is programmed to be fully compatible and functional with all
intended CISCO OC-3, OC-12, OC-48 switching devices. This SFP optical transceiver is based on the
ATM/SONET/SONET standard and is designed to be compliant with SFF-8472 SFP Multi-source
Agreement (MSA). This module is designed for single mode fiber and operates at a nominal wavelength
of 1550nm.

Features:
• Up to 2.67GBd bi-directional data links
• Hot-pluggable SFP footprint
• Uncooled 1550nm DFB laser transmitter
• Duplex LC Connectors
• Built in Digital Diagnostics
• Up to 15km over 9/125 SMF
• Single power supply 3.3V
• Operating temperature range
C-Temp: 0℃ to 70℃

Compliance:
• ANSI-T1.646, ATM and SONET and SDH for OC-48/STM-16
• SFP MSA SFF-8472
• RoHS
• Class 1 laser product EN 60825

Applications
• SONET OC-48 IR-2/SDH STM S-16.2
• SONET OC-12 IR-2/SDH STM S-4.2
• SONET OC3 IR-2/SDH STM S-1.2
• 1.25GBd Gigabit Ethernet
• 2.125GBd / 1.08GBd Fiber Channel

Warranty:
GigaTech Branded Optical Transceivers- Lifetime Warranty

GigaTech Products, Inc. - 3188 Airway Ave, Suite G, Costa Mesa, CA 92626 - 877-7-GIGATEC
www.GigaTechProducts.com
 SFP-OC48-IR2-GT
SFP OC-48/STM-16 Intermediate-Reach 1550nm Cisco Compatible M

General Specifications
Parameter Symbol Min Typ Max Unit Remarks
Data Rate DR 2.488 GBd
Bit Error Rate BER 10-12
Input Voltage VCC 3.1 3.3 3.6 V
Maximum Voltage Vmax -0.5 4.5 V Electric Power Interface
Supply Current Is 200 300 mA Electric Power Interface
Storage Temperature Tsto -40 85 ℃ Ambient Temperature

Optical Characteristics - Transmitter

Parameter Symbol Min Typ Max Unit Remarks
Optical Center Wavelength  1260 1360
nm
Output Optical Power Ptx -5 dBm 0 Class 1 Product
Extinction Ratio ER 10 11 dB
Spectral Width (RMS)  1 nm
Relative Intensity Noise RIN – 120 dB/Hz
Optical Rise/Fall Time TRF_IN 160 ps
Generated Jitter (peak to peak) GTT 0.07 UI
Generated Jitter (rms) GTRMS 0.007 UI
Output Eye Compliant with SONET OC-48/SDH STM-16 Standard

Optical Characteristics - Receiver

Parameter Symbol Min Typ Max Unit Remarks
Optical Center Wavelength C 1260 1600 nm
Average Rx Sensitivity @ OC48 RX_SEN -18 0 dBm PRBS 223-1
Loss of Signal-Asserted PLOS_A -30 dBm
Loss of Signal-Deasserted PLOS_D -18 dBm
Loss of Signal-Hysteresis 0.5 dB

Electrical Characteristics – Transmitter

Parameter Symbol Min Typ Max Unit Remarks
Input differential impedance Rin 100 Ω Non Condensing
Single ended data input swing VIN_PP 250 1200 mV
Transmit Disable Voltage VD VCC -1.3 VCC V
Transmit Enable Voltage VEN VEE VEE +0.8 V
Transmit Disable Assert Time 10 Us

Electrical Characteristics – Receiver

Parameter Symbol Min Typ Max Unit Remarks
Single ended data output swing VOUT_PP 300 400 800 mV
Data output rise time TR 100 170 ps 20%-80%
LOS Fault VLOS_F VCC -0.5 VCC_HOST V
LOS Normal VLOS_N VEE VEE +0.5 V

GigaTech Products, Inc. - 3188 Airway Ave, Suite G, Costa Mesa, CA 92626 - 877-7-GIGATEC
www.GigaTechProducts.com
 SFP-OC48-IR2-GT
SFP OC-48/STM-16 Intermediate-Reach 1550nm Cisco Compatible M

Digital Diagnostic Functions

The SFP supports the 2-wire serial communication protocol as defined in the SFF 8472. Digital diagnostic
information are accessible over the 2-wire interface at the address 0xA2. Digital Diagnostics are internally
calibrated by default. A micro controller unit inside the transceiver gathers the monitoring information and reports
the status of transceiver.
Transceiver Temperature- Internally measured, represented as a 16 bit signed twos complement value in
increments of 1/256 degrees Celsius, Temperature accuracy is better than ±3 degrees Celsius over specified
operating temperature and voltage.
Transceiver Supply Power- Internally measured, represented as a 16 bit unsigned integer with the voltage
defined as the full 16 bit value (0 – 65535) with LSB equal to 100 μVolt, yielding a total range of 0 to +6.55 Volts.
Transceiver TX bias current- Internally measured, represented as a 16 bit unsigned integer with the current
defined as the full 16 bit value (0 – 65535) with LSB equal to 2 μA, yielding a total range of 0 to 131mA. Accuracy is
better than ±10% over specified operating temperature and voltage.
Transceiver TX output power- Internally measured, represented as a 16 bit unsigned integer with the power
defined as the full 16 bit value (0 – 65535) with LSB equal to 0.1 μW. Data is assumed to be based on measurement
of laser monitor photodiode current. Accuracy is better than ±3dB over specified temperature and voltage. Data is
not valid when the transmitter is disabled.
Transceiver RX received optical power- Internally measured, represented as a 16 bit unsigned integer with the
power defined as the full 16 bit 35 value (0 – 65535) with LSB equal to 0.1 μW. Accuracy is better than ±3dB over
specified temperature and voltage.
Parameter Symbol Accuracy Units Report Range Unit Remarks
Temperature TMON ±3 ℃ -40 - +95 ℃
Voltage VMON ±0.1 V 2.7 - 3.9 V
Bias Current TF ±10 % 1 – 80 mA
Tx Power VLOS_F ±3 dB -10 - +5 dBm
Rx Power VLOS_N ±3 dB -25 - +5 dBm

Dimensions

ALL DIMENSIONS ARE ±0.2mm UNLESS OTHERWISE SPECIFIED UNIT: mm

GigaTech Products, Inc. - 3188 Airway Ave, Suite G, Costa Mesa, CA 92626 - 877-7-GIGATEC
www.GigaTechProducts.com
 SFP-OC48-IR2-GT
SFP OC-48/STM-16 Intermediate-Reach 1550nm Cisco Compatible M

PCB Layout Recommendation

GigaTech Products, Inc. - 3188 Airway Ave, Suite G, Costa Mesa, CA 92626 - 877-7-GIGATEC
www.GigaTechProducts.com
 SFP-OC48-IR2-GT
SFP OC-48/STM-16 Intermediate-Reach 1550nm Cisco Compatible M

Block Diagram of Transceiver

Transmitter Section- The DFB laser driver accept differential input data and provide bias and modulation
currents for driving a laser. An automatic power-control (APC) feedback loop is incorporated to maintain a
constant average optical power.1550nm in an eye safe optical subassembly (OSA) mates to the fiber cable.
TX_DISABLE- The TX_DISABLE signal is high (TTL logic “1”) to turn off the laser output. The laser will turn on
within 1ms when TX_DISABLE is low (TTL logic “0”).
TX_FAULT- When the TX_FAULT signal is high, output indicates a laser fault of some kind. Low indicates normal
operation.
Receiver Section- The receiver utilizes a PIN detector integrated with a trans-impedance preamplifier in an OSA.
This OSA is connected to a Limiting Amplifier which providing post-amplification quantization, and optical signal
detection. The limiting Amplifier is AC-coupled to the transimpedance amplifier, with internal 100Ω differential
termination.
Receive Loss (RX_LOS)- The RX_LOS is high (logic “1”) when there is no incoming light from the companion
transceiver. This signal is normally used by the system for the diagnostic purpose. The signal is operated in TTL
level.
Controller Section- The micro controller unit monitors the operation information of LD driver and Limiting
Amplifier and report these status to the customer.

GigaTech Products, Inc. - 3188 Airway Ave, Suite G, Costa Mesa, CA 92626 - 877-7-GIGATEC
www.GigaTechProducts.com
 SFP-OC48-IR2-GT
SFP OC-48/STM-16 Intermediate-Reach 1550nm Cisco Compatible M

Electrical Pad Layout

GigaTech Products, Inc. - 3188 Airway Ave, Suite G, Costa Mesa, CA 92626 - 877-7-GIGATEC
www.GigaTechProducts.com
 SFP-OC48-IR2-GT
SFP OC-48/STM-16 Intermediate-Reach 1550nm Cisco Compatible M

Pin Assignment
PIN # Symbol Description Remarks
1 VEET Transmitter ground (common with receiver Circuit ground is isolated
ground) from chassis ground
2 TFAULT Transmitter Fault
3 TDIS Transmitter Disable. Laser output disable on Disabled: TDIS>2V or open
high or open Enabled: TDIS<0.8V
4 SDA Data line for serial ID Should Be pulled up with
5 SCL Clock line for serial ID 4.7k – 10k ohm on host
6 MOD_ABS Module Absent. Ground within the module board to a voltage between
2V and 3.6V
7 RS0 No Connection required
8 LOS Loss of Signal indication. Logic 0 indicates LOS is open collector
normal operation output
9 RS1 +3.3V Power Supply Circuit ground is isolated
10 VEER Receiver ground (common with transmitter from chassis ground
ground)
11 VEER Receiver ground (common with transmitter
ground)
12 RD- Receiver Inverted DATA out. AC coupled
13 RD+ Receiver Non-inverted DATA out. AC coupled
14 VEER Receiver ground (common with transmitter Circuit ground is isolated
ground) from chassis ground
15 VCCR Receiver power supply
16 VCCT Transmitter power supply Same as Pin# 1
17 VEET Transmitter ground (common with receiver Circuit ground is connected
ground) to chassis ground
18 TD+ Transmitter Non-inverted DATA out. AC
coupled
19 TD- Transmitter Inverted DATA out. AC coupled
20 VEET Transmitter ground (common with receiver Circuit ground is connected
ground) to chassis ground

References
1. IEEE standard 802.3. IEEE Standard Department, 2002.
2. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000.
3. Digital Diagnostics Monitoring Interface for Optical Transceivers – SFF-8472.
4. Bellcore GR-253 and ITU-T G.957 Specifications.

GigaTech Products, Inc. - 3188 Airway Ave, Suite G, Costa Mesa, CA 92626 - 877-7-GIGATEC
www.GigaTechProducts.com