TCL

SERVICE MANUAL

32S6S/NT63BP1-AG

1. Caution…………………………………………………………………………
2. specification……………………………………………………………………
3. Alignment Procedure…………………………………………………………
4．Block diagram…………………………………………………………………
5．Scheme Diagram ……………………………………………………………
6. Troubleshooting………………………………………………………………
([SORGHGUDZLQJ

This m anual i s t he l atest at t he t ime of pr inting, and doe s not

include the modification which may be made after the printing, by
the constant improvement of product
 SCHNEIDER ELECTRONICS GMBH-GERMANY
1. CAUTION
CA UTION:
Use of controls, adjustments or procedures other than those specified herein may result in
hazardous radiation exposure.

CA UT ION : T O RE DUCE TH E RIS K OF

CA U T ION ELECTR ICA L SHOCK, DO NOT RE MOVE
RISK OF ELECTRIC
ELECTRI COVER (OR BACK). NO USER SERVICEABLE
SHOCK DO NOT OPEN. PAR TS INS IDE . RE FE R SE R VIC ING TO
QUALIFIE D SERVICE PERSONNEL.

The lighting flash with arrowhead symbol, with an equilateral triangle is intended to
alert the user to the presence of uninsulated dangerous voltage within the products
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
the person.

The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

2
 SCHNEIDER ELECTRONICS GMBH-GERMANY

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:
Read all of these instructions. Sa ve these instructions for later use . Follo w all W arnings and
Instructions marked on the audio equipment.
1. Read Instructions-All the safety and operating instructionsshouldbe read before the productis operated.
2. Retain Instructions- The safety and operating instructions should be retained for future reference.
3. Heed Warnings- All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions- All operating and use instructions should be followed.

FOR YOUR PERSONAL SAFETY

1. When the power cord or plug is damaged or frayed, unplug this television set from the wall outlet and refer servicing to
qualified service personnel.
2. Do not overload wall outlets and extension cords as this can result in fire or electric shock.
3. Do not allow anything to rest on or roll over the power cord, and do not place the TV where power cord is subject to
traffic or abuse. This may result in a shock or fire hazard.
4. Do not attempt to service this television set yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
5. Never push objects of any kind into this television set through cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the television set.
6. If the television set has been dropped or the cabinet has been damaged, unplug this television set from the wall outlet
and refer servicing to qualified service personnel.
7. If liquid has been spilled into the television set, unplug this television set from the wall outlet and refer servicing to
qualified service personnel.
8. Do not subject your television set to impact of any kind. Be particularly careful not to damage the picture tube surface.
9. Unplug this television set from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
10.1. Do not place this television set on an unstable cart, stand, or table. The television set may fall, causing serious injury
to a child or an adult, and serious damage to the appliance. Use only with a cart or stand recommended by the
manufacturer, or sold with the television set. Wall or shelf mounting should follow the manufacturer s instructions, and
should use a mounting kit approved by the manufacturer.
10.2. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces
may cause the appliance and cart combination to overturn.

3
 SCHNEIDER ELECTRONICS GMBH-GERMANY

PROTECTION AND LOCATION OF YOUR SET

11. Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, etc.
Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall
outlet and refer servicing to qualified service personnel.
12. Choose a place where light (artificial or sunlight) does not shine directly on the screen.
13. Avoid dusty places, since piling up of dust inside TV chassis may cause failure of the set when high humidity persists.
14. The set has slots, or openings in the cabinet for ventilation purposes, to provide reliable operation of the receiver, to
protect it from overheating. These openings must not be blocked or covered.
Never cover the slots or openings with cloth or other material.
Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc.
Never place the set near or over a radiator or heat register.
Never place the set in a built-in enclosure, unless proper ventilation is provided.

PROTECTION AND LOCATION OF YOUR SET

15.1. If an outside antenna is connected to the television set, be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges, Section 810 of the National Electrical Code, NFPA No.
70-1975, provides information with respect to proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection
to grounding electrode, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA
LEAD- IN WIRE

GROUND CLAMP

ANTENNA DISCHARGE
UNIT (NEC SECTION
810-20)

GROUNDING
CONDUCTORS
ELECTRIC SERVICE (NEC SECTION810-21)
EQUIPMENT

GROUND CLAMPS

POWER SERVICE GROUNDING

NEC-NATIONAL ELECTRICAL CODE ELECTRODE SYSTEM
(NEC ART 250. PART H)

15.2. Note to CATV system installer : (Only for the television set with CATV reception)
This reminder is provided to call the CATV system installer s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
16. An outside antenna system should not be located in the vicinity of overhead power lines or other electric lights or power
circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
17. For added protection for this television set during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage due to lightning
and power-line surges.

4
SCHNEIDER ELECTRONICS GMBH-GERMANY

OPERATION OF YOUR SET

18. This television set should be operated only from the type of power source indicated on the marking label.If you are not
sure of the type of power supply at your home, consult your television dealer or local power company. For television
sets designed to operate from battery power, refer to the operating instructions.
19. If the television set does not operate normally by following the operating instructions, unplug this television set from the
wall outlet and refer servicing to qualified service personnel. Adjust only those controls that are covered in the operating
instructions as improper adjustment of other controls may result in damage and will often require extensive work by a
qualified technician to restore the television set to normal operation.
20. When going on a holiday : If your television set is to remain unused for a period of time, for instance, when you go on
a holiday, turn the television set off and unplug the television set from the wall outlet.

IF THE SET DOES NOT OPERATE PROPERLY

21. If you are unable to restore normal operation by followingthe detailedprocedurein your operatinginstructions,
do not attempt any further adjustment. Unplug the set and call your dealer or service technician.
22. Whenever the television set is damaged or fails, or a distinct change in performance indicates a need for
service, unplug the set and have it checked by a professional service technician.
23. It is normal for some TV sets to make occasional snapping or popping sounds, particularly when being
turned on or off. If the snapping or popping is continuous or frequent, unplug the set and consult your
dealer or service technician.

FOR SERVICE AND MODIFICATION

24. Do not use attachments not recommendedby the television set manufacturer as they may cause hazards.
25. When replacementparts are required, be sure the service technician has used replacementparts specified
by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, or other hazards.
26. Upon completion of any service or repairs to the television set, ask the service technician to perform
routine safety checks to determine that the television is in safe operating condition.

5
 PRODUCT SPECIFICATION RELEASE
Model: 32S6/NT63PB1-AG/CJ9W10
Version：1.1 Issued On: 2017-11-27
Basic Information Sound
Product Type LED HD Smart DTV Speakers Integrated speakers (Bottom side)
Chassis NT63EP1-LA Audio Power Output（THD=7%） 2×5W
CPU CA9 *2, 896MHz Sound Preset Standard\Movie\Music\VoiceStadium\Personal
GPU Mali-400*2 TV Placement Desk top / Wall mount
OS Linux Audio Delay Yes
RAM/ROM DDR : 256MB +512MB/EMMC: 4GB Dolby MS11
UI Style TV+2.0 UI Night mode No
Launcher HomePages Show Home、Video、TV、Apps.

OSD Language English/Spanish/Portuguese

ATV：NTSC-M, PAL-M，PAL-N
TV System
DTV：ISDB-T
AV System NTSC
Panel Specification
HDMI&HDCP Version HDMI1.4，HDCP1.4&HDCP2.2 Backlight Technology D-LED Backlight
HDR No Panel supplier CSOT
Power Supply AC 100V-240V 50/60Hz Aspect Ratio 16:9
Power Consumption（TV On） 50W Panel Active Size (inch) 31.5''
Power Consumption（Standby） ﹤0.5W Display Resolution 1366*768
ECO Energy Efficiency Yes Brightness (cd/m2) 240nit（Type）
CB、Dolby/MS11、HDMI Contrast Ratio 3000:1
Certification
YouTube、NETFLIX Response Time (G to G) 6 5ms（Type）
6.5ms（Type）
WiFi integrted 2*2 b/g/n Viewing Angle (H/V) 178°/178°
Internet Link WiFi 2.4GHz Life Time(Typ.) 30,000hrs
Ethernet Network Color 16.7M (8bit)
In Center of Front, white in Standby Refresh Rate 60Hz
LED Indicator Status
Normal/Flashing/Off

Basic Function Terminals

Initial Setup Yes，for user setting in TV first starting
Instant Power on a special standby mode for starting less than 4s
Channels Edit Only Channel Skip
Input Settings For Input source device name choice and Edit
Input Method For input source device choice
System Update Yes
T-Link（CEC） Yes
Teletext Close Caption
Audio Language/Nicam No
PVR/Timeshift Yes （Only for DTV Programme）
EPG Yes（Only for DTV Programme）
Subtitle Yes（Only for DTV Programme）
E-Manual General basic function introduction.
E-Sticker Yes
Parental Control Yes

Picture
Picture Mode Standard\Dynamic\Natural\Stadium\Movie
16:9\4:3\Cinerama\14:9 Zoom
Screen Mode
16:9 Zoom\16:9 Zoom up\Automatic
Noise Reduction L \Middl \Hi h\A \Off
Low\Middle\High\Auto\Off
Backlight Adjustable Yes (0~100)
Color Temperature Normal/Cold\Warm/Customer
Color Space Auto\Native\Customer
Dynamic Contrast Yes
Overscan Yes
Sports Mode Yes，Enhance perception of football game
Picture Reset Yes
Micro Dimming Yes,Signal processing in sub-area
10 Point white balance Yes for user adjust
Yes,for

USB Device Media Format

Music PCM, MP3, AC3, WMA, HE-AAC
Picture JPEG/PNG/BMP
Mutilmedia Video/Audio Decoder H.264,H.265,MPG1/2/4,WMV,VC1,VP8,VP9
Video Format up to 1080P@60Hz
Correct specifications/outward depend on the actual model,all specifications are subject to change without prior notice.

Featured Application List Essential Accessories（Default）

Netflix Watch TV Shows Online, Watch Movies Online Operation Manual English(Default)
YouTube Push Popular VOD posters to Homepage Remote Control and batteries RC802N (with 2 batteries)
TV+ App Store Store with lots of Apps Base Stand Integrated Packaging
T-Browser Webpage Browser AC Power Cord 1 pcs
Wireless Mirroring connecting,to deliver picture 、audio、 video
content from smartphone to TV
T-CAST
Connect Mobile phone to TV sets and control the TV like Remote
Control

Media center Media/Music play for USB Device

Mechanical ID Picture

Mechanical Key Specification

W1 (mm) 727 Carton Dimensions WxDxH（mm） 850*133*535
D1 (mm) 76.5 Container Loading---20 feet（pcs） 484
H1 (mm)
( ) 424 Container Loading---40
g feet（pcs）
p 1026
W2 (mm) 727 Container Loading--40 feet High（pc 1209
D2 (mm) 190 Net Weight With Stand （Kg）
H2 (mm) 476 Net Weight Without Stand （Kg） ---
SD (mm) 553 Gross Weight With Packaging （Kg）

Wall-Mount VESA
VESA Mounting WMB233
VESA Hole Pattern 100*200mm
Screw Size M4*10
Screw Length（mm） 10mm
Screw Pitch（mm） 1mm
Screw Quantity 4

Base Stand Specifications Material

Screw Size M4*20 Front Rail Black high gloss molding（painting optional）
S
Screw ）
Length（mm）
L th（ 20mm Co er
Back Cover Te t ring Injection
Texturing
Screw Pitch（mm） 2.24mm Rohs No
Screw Quantity 4 Fire-Proof Level HB75 (Front and Back Cover)

Drafted by: Approved by:

 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

TCL World-Wide R&D

FPD CENTER

Test & Alignment Specification (TAS)

for NT72563
Version 1.0

PREPARED BY : 舒相成 DATE : 2017-6-12 ，

CHECKED BY : DATE : ，

APPROVED BY : _____ DATE : ，

Page 1 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

Disclosure

The information contained in this document is proprietary to TCL SZ FPD lab and shall not be disclosed by the
recipient to third persons without the written permission of the team leader or GM of R&D.

Revision History

Version Issue Date Description of changes

V1.0 2017-06-12 This is the initial version

Page 2 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

These chassis are designed for European LCD TV markets Ready for IPTV. The main chip is from novatek NT72563
series with embedded Linux core and supports below features matrix:

Page 3 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

IC Details & Position

Market NT63B1-AP NT63EP1-LA ---
Main SW UF1 UF1
IC Details
EMMC(4GB/8GB) 4GB 4GB
&
BIN image V8-N563T01-LF1VXXX V8-N563T01-LF1VXXX
Position
HDMI SWITCH - EDID
N/A N/A
BIN image

▪ Manufacturing Connectors Pinout

ISP-UART / P15 Pin1: NC Pin2: RXD Pin3: TXD Pin4: GND

▪ USB to UART Bridge Adapter (FT2232D chipset series)

To communicate with TV product for debugging, adjustment and so… it’s required suitable 0.5V Serial Interface like
following snapshot (further details are described on below sections):

Page 4 of 25
新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

Page 5 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

INFO:

 All tests and measurements mentioned hereafter have to be carried out at a normal mains voltage (220 ~ 240 VAC)
 All voltages have to be measured with respect to ground, unless otherwise stated
 All final tests have to be done on a complete set including LCD panel in a room with temperature of 25+/-7°C
 The Picture Performance assessment such as White Balance (luminance and colour temperature) has to be
performed into subdued lighted room after at least 45min of warm-up in order to avoid any temperature drift influence
(colorimetric vs. time)

1. PCB/SKD Assembly: Test & Alignment

1.1. Pre-Conditions and DC/DC Check

Before power-on, please check the board according to the relevant block diagram and circuit diagram, and make
sure that no serious issue or mistake can destroy the board. For example, the output of DC/DC and LDO should not be
shorted to ground.
Supply a suited voltage and power-on, then check the voltage according to the relevant block diagram, circuit
diagram and voltage specification.
For example, check SoC voltage (3V3, 1V8, CORE_1V2, 5V, 5VSTB, etc.), DDR voltage (DDR_1V5), audio
amplifier voltage (12V), etc...
Measurements should fulfill specification within ±5% tolerances.
Note①: See enclosed circuit diagram for more details.

1.2. SW Image download

Download the latest release SW from below FTP server:
- Link: \\10.120.99.200\
- Username:
- Password:
- Folder: \\10.120.99.200\Software_release\Debugging_TS_SW\Novtek\NT563

1.2.1 LR or PR step. ---Only test

In case of starting from blanked flash / eMMC, it’s necessary to use “Blank upgrade” to update the SW.

See Appendix ⑴ “How to upgrade FLASH SW using Blank upgrade”

See Appendix ⑵ “How to upgrade main SW using USB”
See Appendix ⑶ “How to upgrade main SW using USB and RCU”

Page 6 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

1.2.2 MP Step
In case of starting from blanked flash, it’s necessary to write “ V8-N563T01-LF1VXXX _emmc_writer.bin” file via
factory copy in advance.

▪ OAD Stream

To manage quicker mass reflashing on predefined DVB Channel, some licensed IBL tools ('xxx2lli.exe', 'lli2dsm.exe',
dsmmerge.exe …) from Intel byte Inc. might be necessary to create appropriate DVB SSU image. Over some predefine
settings such as repeated data block insertion, null packets size, … that are controllable in configuration file, here below
are mandatory OUI entries structure to prepare DSM-CC carousel image format:
- export CUST_OAD_OUI 0x001C50
- export CUST_OAD_HW_MODEL 0x5395
- export CUST_OAD_HW_VERSION 0x0000
- export CUST_OAD_SW_MODEL 0x0001
- export CUST_OAD_SW_VERSION 0x00
OAD reflashing is managed within 4 steps operation: multiplex detection, DVB transfer, flashing and warm-start.

See Appendix ⑷ “How to upgrade FLASH SW and EEPROM Clone using OAD”

1.3. UART & IR Parser

To use both UART and/or IR parser, TV has to be set in Factory mode with its USB port well connected to suitable
UART device or an IR emitter device correctly facing up TV (see below “Product Assembly - section 2.0” how to
activate “Factory key”).
The UART parser engine is enabled by sending following command “0xE2” from host to TV within following presets
115200/8/n/1.
Once initialized, “PS” caption is toggle displayed on bottom left screen (“S” like Serial).
To communicate with TV depending on SIACP revision layout implementation, you need to fulfill UART/IR
commands protocol and format described on enclosed SIACP requirements document (rev. v3.9).

1.4. Project ID Modification

There are different IDs stored in the eMMC depending on different Panels settings and Models features, but there’s
only one key branching Project ID that includes all. So, it’s not recommended to modify Panel ID with Hyper terminal as
other ID features may not change!
To modify Project ID, you need to go through “Factory menuOtherProject ID-->Project ID”, then spin left or
right with RCU “◄/►” keys to chose suitable ID (Project name is dynamically refreshed).It is necessary to press “OK”
key for saving the setting.

See Appendix ⑸ “How to change Project ID with RCU”

See below is the ProjectID table for reference:

MODEL-LA ProjectID PanelID Panel Name MODEL-AP ProjectID PanelID Panel Name

40D2900 1 1 V400HJ6 43D2900 4 4 ST4251B02-1

40D2900 2 2 V400HJ6

Page 7 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

L32S4900S 3 3 ST3151A05-9

Note②:More and more project ID will be added in the future.

1.5. Functional Test

Once the boards (chassis, KB, IR, PSU…) and the panel are well interconnected, plug all external generator
devices to relevant below inputs/outputs using respective test patterns format to check picture and sound quality:

Source Test Signal Test Pattern

2D - Movie 1280x720
2D - Static Picture 1920x1080
Analog /Digital Tuner
RF cable generator 1. Frequency Range: full band
(VHF/UHF & CATV)
2. Standard: PAL / SECAM
3. DVB-T/C
2D - Movie 720x576
1. Frequency Range: 950MHz..2150MHz
2. Symbol Rate Range:
DVB-S 1..30MHz (for QPSK)
Satellite Tuner
DVB-S2 1..45MHz (for QPSK)
Compliant DVB-S/S2 1..30MHz (for 8PSK)
- DiSEqC v1.0 (A, B, C, D) and Tone
source from generator or 3. LNB Voltage Range:
Burst (A, B)
dish antenna with switch Vertical 12.85V..14.2V
- Double LNB frequency (band change
Horizontal 17.6V..19.5V
by 22KHz Tone)
4. 22KHz Tone Range
Frequency 20.5KHz..23.5KHz
Amplitude 400mV..900mV
Current ≥400mA
SPDIF (optical) Audio Amplifier PCM or Dolby D+
PCMCIA CI CAM card adaptor Conax, Irdeto, Viaccess, …
SCART1 IN via adapter PAL Half Color & Gray bars 720x576
Chroma/Fluke generator
(CVBS & RGB & S-VIDEO) Half Color & Gray bars

Page 8 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

SCART1 OUT via adapter

RF signal Suitable channel
(DVB-T & CVBS out)
CMP via mini jack adaptor Chroma/QuantumData 1920x1080i@60Hz
(YPrPb & Audio) generator Half Color & Gray bars
with beyond HDMI 1.3 and
HDMI HDCP compliant DVD/BD 2D - Movie 1280x720i@60Hz
(Video & Audio) player

RJ45
DHCP Server ICMP packets echo request
(LAN)
Headphone via mini jack adapter RF signal Suitable channel
Loud Speakers / Enclosures RF signal Suitable channel

Audio tones can be defined by the factory (ie: 1KHz & 3KHz, sweep …).
Picture video formats can be changed by the factory according to their own standard.

1.6. AD Calibration Test

As the A/D self-calibration mechanism is built-in Soc, there’s no any ADC to perform.

1.7. DDC & EDID & T-Link Test

The E-EDID data structures are according to VESA Enhanced EDID 1.3 (and EIA/CEA-861B for HDMI). CEA Timing
Extension structure has been extended to support all 3D capable timings.
All HDMI structures have their own BIN profile which are part of main SW and uploaded at power-on into soc chipset:
For EDID check, it’s needed to check whether the correct EDID is downloaded by checking corresponding EDID
NVM Checksum or read them out to check bit by bit if it is in line with the released EDID bin file.

1.8. HDCP Test

For HDCP compliancy, it’s needed to check whether the HDCP key has been well set by connecting suitable
generator.

1.9. CI+ Key Upgrade, Activation and Test

See Appendix ⑹ “How to upgrade CI Key using USB”
See Appendix ⑺ “How to upgrade ESN Key using USB”
See Appendix ⑻ “How to upgrade HDCP key & HDCP2.0 key using USB”

1.10. LAN and WLAN Test (MAC address and Device/User ID codes)
Here are some representative codes examples:

Device ID User ID MAC Address

54ad21daec2359799f677a2708389862538750ff 111382090 5C:36:B8:A8:9D:CC

▪ MAC Address Upgrade (IPv6)

Page 9 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

MAC can be set using UART commands described on enclosed SIACP requirements (rev. v3.9).
- Writing MAC command <0xB3>, Data length <6>, Data type <HEXA> (see below command example from above
MAC code)
<AA 0B B3 5C 36 B8 A8 9D CC 36 78>

See Appendix ⑼ “How to upgrade MAC Address using USB”

▪ Device ID (DID)

Purpose is to allow Other Newtork Download (OND) and further specific Services via dedicated abroad portal (UK
tbc).4 At final, when TV may ask for portal connection, there’ll be Device ID matching control sent by host (TV client)
to ensure total integrity.

For such, specific DID (40 bytes) needs to be paired and overwritten into memory for internal client encryption.
All DID and MAC codes have to be download from portal local service via suitable factory workstation LAN system.
Then during production lot, it’s necessary to send/write all those codes to each TV.
DID codes can only be set using UART commands described above on enclosed SIACP requirements (rev. v3.9).
- Writing Device ID command <0xB2>, Data length <32>, Data type <ASCII> (see below command example from
above DID code)
<AA 25 B2 42 45 34 46 32 35 35 42 42 44 31 30 36 42 43 38 46 38 30 36 41 45 34 35 36 33 35 30 44 39 31 46 48
93>

▪ LAN Test

A rough LAN test can be done by connecting DHCP server to TV’s RJ45 and check that IP, subnet mask, DNS, …
addresses are visible on “Settings NetworkInternet connection(On)IP settings”.
More in-depth test can be performed faster using suitable UART/IR commands following SIACP requirements. SW
will internally manage Network ID (NID) flag controlling all MAC/DID/UID integrity to facilitate PA screening further.

See Appendix ⑽ “Network Connection Setup”

See Appendix ⑾ “How to upgrade Flash SW using Network”

Note③: It’s not necessary to check video and audio from DLNA server.

Page 10 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

2. Product Assembly (PA): Test & Alignment

2.1. Factory Menu

Follow the below steps to pop-up the Factory menu in case of “Factory hotkey” is disabled:
- Press RCU “MENU” key to display Setting menu
- Select Picture
- Scroll down to “Contrast” item
- Press the subsequence RCU keys “9”, “7”, “3” and “5”

In case of “Factory hotkey” is enabled, just press RCU “Return” key（ ） to pop-up again the Factory menu.
The status of “Factory Key” can be changed in “Factory Menu->Hotkey”
Press RCU “OK/►” key to enter the submenu.
Press RCU “Menu” key to go back to the root menu.
Press RCU “◄/►” key to change the values.
Press RCU “OK” key run the function.
Press RCU “Exit” key exit the Factory menu.

▪ Factory Captions Description

While “Factory hotkey” is enabled, there’s some toggled display information (~2s) relative to SW, Project ID,
CI+, Network ID to facilitate 100% quick screening without accessing to whatever else menu:

Main SW Ver
Project ID (ID)
ERG(PVR)
CI Key Activation flag (CI+ key)
MID(Internet infor for factory)
P (Production/Factory mode flag) / S (Factory UART Parser mode flag) / W (Warm-Up mode flag)

See Appendix ⑿ “Factory Menu Description”

2.2. Warm-up Test

Following TCL standard and practices, it’s required minimum 15min of Warm-Up that can be considered as Burn-In.
Additional Aging for White Balance alignment is no more necessary due to consistent Picture Performance with
Cloning usage.
This function is accessible by selecting “Factory menu WARM UP”, pressing RCU “OK/►” key and then leaving
Factory menu by pressing “Exit” key. To release/disable Burn-in mode, it’s just required to press “Menu” button from
local keyboard. Other faster methods via UART/IR commands are available on enclosed SIACP requirements (rev.
v5.4).

Page 11 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

2.3. White Balance

▪ White Balance Touch-Up (Golden sample)

As some color coordinates discrepancies can be noticed from panel batches to others, it may necessary to perform
slight touch-up.
For Color temperature adjustment, switch TV on leading HDMI input where should be connected suitable generator
providing following format 1280x720p@60Hz test pattern. A 32 steps grey scale is recommended to assess relevant
colorimetry tracking and low/high light saturation points.

Ensure that TV’s picture enhance is off.

Ensure that TV is in Factory mode to access to ”White Balance” adjustment submenu, then scroll down to
toggle off “Pic. Enhance” flag.
WB Normal is the first mode which is adjusted in HDMI source，the next are HDMI warm and cool mode.
Warm and Cool Tone are relatives to Normal mode. WB adjust need to fix default G Gain .Offset registers needn’t
to be adjusted.
➢ “Gain” registers set need to be adjusted at 70IRE.

▪ Targets and Tolerances for all inputs

(According to company uniform LED color temperature standard of panel)

The measured and adjustable parameters should be mainly “x”, “y” coordinates.
The White Balance alignment should be performed using a well calibrated and contact less analyzer (ex: Minolta
CA210 or CA310). The analyzer may not touch the screen surface, and measurement must be performed in a dark
environment keeping the probe(s) at 90+/-2°from the panel center.
The results should fulfill specification for each TV set offered by R&D and below tolerances::

NT72563 Energy FW Min (Nits) Preset Targets (x, y)

panel name
Model Efficient FW>Min COOL NORMAL WARM
43D2900 ST3151A05-9 A+ 250

Page 12 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

Targets Tolerances
COOL NORMAL WARM ALIGNMENT MEASUREMENT
Coordinate “x” ± 0.003 ± 0.020
Offered by R&D PQ engineer
Coordinate “y” ± 0.003 ± 0.020

Important: If measurements are performed on whatever else LED panel with Minolta CA210, it’s required to
calibrate additional channel (ex: CH01) using relative following offsets (CH00 remains for CCFL panel): +0.002 for “x”
and +0.012 for “y”.
Note④: See WB list as follows for more details.

▪ Cloning

Once a TV is well aligned and prepared (channels maps, volume, picture presets…), user can prepare golden clone
image that can be copied on demand to all further TV production lot of same TV. To access cloning function, you can
select “Factory menu USB Clone && Update”, Scroll down to “TV to USB” or “USB to TV” and press RCU “OK/►”
key to process. 4 BIN images will be created, overwritten or read on USB stick (pen drive) depending on chosen
template like following: “database\database\***.db”. These files need to be used strictly with MT5655 SoC platform as
depending on SW structure.
Other faster access methods via UART/IR commands are available on enclosed SIACP requirements (rev. v3.9).

2.4. High Pot and Insulating Resistance Tests

At the end of the process, a “High Voltage” and an “Insulating Resistance” tests are required to fulfil Safety
Electrical requirements (CEI 65065).
▪ High Voltage Withstanding requirements ▪ Insulating Resistance requirements

- “Voltage”  3500 VAC - “Voltage”  500 VDC

- “Max Leakage Current”  10 mA - “Threshold Min”  4M Ω
- “Test Time”  3 sec - “Test Time”  2 sec

2.5. SHOP-END Test

At final process stage, it’s necessary to perform “Reset shop” before any packing to leave Factory mode and
restore User default presets.
This function is accessible by selecting “Factory menu Reset Shop”, then pressing RCU “OK/►” key. Other
faster methods via UART/IR commands are available on enclosed SIACP requirements (rev. v5.4).

Page 13 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

Note⑤:A password might be required in case of Parental Control function is locked, use default “1234” password or
“0423” super password to clean-up existing ones if forgotten.

END

Appendix ⑴ “How to upgrade SW FLASH using Blank upgrade”

➢ Download boot bin “ tcl_m1v1_eu_secure_emmcboot.bin” & blank upgrade main software“upgrade_loader.pkg”

from the software website.

➢ Connect UART interface to suitable manufacturing TV input connector, upgrade boot bin first to blank IC.
1) copy all files under the directory to the root directory of the u disk..
2) Serial port with USB 3.0 port, USB flash disk to connect USB 2.0.
3) Locate the p901 port on the motherboard ( near the high frequency tuner ), short with tweezers or
other tools.
4) Ac on the AC, the following serial port shows that is in the air, tweezers and other tools to remove, do
not need to be short.

Page 14 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

➢ After finish update SW, TV will reboot automatically and please remove USB key.

➢ Remember to perform “Factory menuReset ALL“ and “Factory menuReset Shop“, and then press RCU
“OK/►” key

Appendix ⑵ “How to upgrade main software using USB”

➢ Copy the MAIN SW BIN image “V8-N563T01-LF1Vxxx.bin” into USB stick (pen drive) root path.
➢ Name “V8-N563T01-LF1Vxxx.bin” as “update.zip”, please delete other xxx.pkg files from USB stick.
(Make sure the USB remaining available storage is more than 1GB)
➢ Plug USB stick to the TV.
➢ Power on TV by AC, at the same time press “power on” key for 10s, TV will update SW automatically.
➢ When reflashing is successful, TV should restart automatically (about 4min).
➢ Remember to perform “Factory menuReset ALL“ and “Factory menuReset Shop“, and then press RCU
“OK/►” key.
➢ Finally, restart the TV.

Page 15 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

Appendix (3) How to upgrade main SW using USB and RCU

➢ Power on TV.
➢ Copy the SW BIN image “V8-N563T01-LF1Vxxx.bin” into USB stick (pen drive) root path.
➢ Plug USB stick to the TV.
➢ Option-->settings--> Support--> Software update -->By USB. TV will find Vxxx and please do “update”.
➢ TV will update SW automatically, and show some notes on TV.
➢ When reflashing is successful, TV should restart automatically after ~4min.
➢ Remember to perform “Factory menuReset ALL“ and “Factory menuReset Shop“ and then press RCU
“OK/►” key.
➢ Switch off TV by removing AC cord.
➢ Reconnect AC cord to restart TV.

Appendix (4) “How to change Project ID with RCU”

➢ Process following subsequence IR codes to change projectID: 062598+MENU+xxx (xxx:ProjectID, ex: 001)
➢ If it works, the TV will restart automatically.

Appendix (5) “How to upgrade CI+ Key using USB”

➢ Create a new folder named “CI+KEY” on USB stick (pen driver) root path.
➢ Copy corresponding “*.key” files into CIKEY folder.
➢ Under CIKEY folder, create a new folder named “backup” (once the CI key is overwritten, the matching key file
will be moved to this folder)
➢ Plug USB stick to the TV
➢ Go to “Factory menuOther Update CI+ CredentialUpdate From USB“ and then press RCU “OK/►”
key
The “Valid” flag should now be enabled (turns to “Yes”), “Custom Code” should display “TCL” and “Serial Num.”
field should update with Key number.
➢ Remove USB stick

Note⑹: If unfortunately the process failed, you may need to download new CI key and repeat operation again.

Appendix (6) “How to upgrade Netflex ESN using USB”

➢ Under USB root path, create a new folder named as “esn”, then copy corresponding ESN KEY bin files into this
folder;

➢ Under “esn” path, the key should be named as “nflxk_***”,like this ,

➢ Plug USB stick to the TV;

Page 16 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

➢ Go to “Factory menuUSB Clone && Update ESN Key Upgrade“ and then press RCU “OK” key
➢ Remove USB stick

Note⑺: If unfortunately the process failed, you may need to download new ESN key and repeat operation again.

Appendix (7)“How to upgrade HDCP key & HDCP2.0 key using USB”

➢ Copy HDCP.bin, HDCP2.bin into USB stick (pen drive) root path, please pay attention to the spell.

➢ Picture ->contrast -> “1950” -> Main Menu

➢ Go to “Main Menu Service Menu USB UPDATE  HDCP Upgrade (HDCP2.0 Upgrade)

Appendix (8) “How to upgrade MAC Address using USB”

➢ Go to “Factory menuOtherIPTVUpdate MAC AddressUpdate From USB“ ，but there is no this

function which is only displaying.
The “Written status” flag should now be enabled (turns to “Yes”) and “MAC address” should display
corresponding address like onto below snapshot:

➢ Note⑧: There is no this function which is only displaying.

Page 17 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

Appendix (9) “Network Connection Setup”

Note⑨:You can set up your TV so that it can access the Internet through your local area network (LAN) using a
wired or wireless connection.

▪ Wired Network Connection

You can connect your TV to your LAN using cable in three ways:
1) Plug your TV to your LAN by connecting the LAN port on your TV to an external modem using a Cat5 cable.
2) Plug your TV to your LAN by connecting the LAN port on your TV to an IP Sharer which is connected to an
external modem. Use Cat5 cable for the connection
3) Depending on how your network is configured, you may be able to plug your TV to your LAN by connecting the
LAN port on your TV directly to a network wall outlet using a Cat5 cable (Note that the wall outlet is attached to a
modem or router elsewhere in your house)
➢ Select “Option Settings NetworkInternet connection (On) InterfaceEthernet”, then select “IP
settings” to connect to network.

▪ Wireless Network Connection

To connect your TV to your wireless network, you need a wireless router or modem and a Wireless LAN Adapter.
Connect your “Wireless USB Adapter” (USB dongle) delivered with your TV to your TV’s USB .
➢ Select “Option Settings NetworkInternet connection(On)Interface”, then select “Wireless” to
connect to a wireless network
➢ Select “Wireless settings” and press “OK/►” to enter.

You can setup the wireless network connection three ways:

1) “Scan” mode
➢ Select “Wireless settings Scan”, then press “OK/►”, the TV will scan all available access points and
then display them.
➢ Select an available access point, then press “OK/►” to connect the TV to it.
Note⑩:
- If you select a protected access point, you will have to enter the corresponding password. Press “OK” on the
remote control to display virtual keyboard to enable you to enter the password.
2) “Manual” mode
➢ Select “Wireless settings Manual”, then press “OK/►”, you will be prompted to enter the correct SSID
of an available wireless router to setup the connection.
3) “Auto” mode
If your AP supports WPS (Wi-Fi Protected Setup), you can connect to the network via PIN (Personal
Identification Number) or PBC (Push Button Configuration). WPS will automatically configure the SSID and
WPA key in either mode.
➢ Select “Wireless settingsAuto”, then press “OK/►” to enter.

▪ Network Setup

Page 18 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

➢ Press “Option” on the remote control and select “Option SettingsNetworkInternet connection”. Then
press “OK/►” key to select “On”. Wait until the connection is automatically established.
➢ Select “Option SettingsNetworkConnection test”, then press “OK/►” to check the Internet
connectivity. If failed, follow below steps to ensure connectivity
➢ Select “Option SettingsNetworkIP settings”, then press “OK/►” to enter into “IP settings” submenu
➢ Set “Address type” to “Auto” by pressing “OK/►” key, it will acquire and enter the new detected IP address
automatically
You can also follow below steps to enter your IP address manually
• Set “Address type” to “Manual” by pressing “OK/►” key, then press “▼” key to go to the first entry field

• Enter the “IP address”, “Subnet mask”, “Default gateway”, “Primary DNS” and “Secondary DNS”
values. Use remote control digital keys to enter numbers and “◄/►” key to move from one to other field
location
➢ After setting all required inputs, select “Option-->Settings NetworkConnection test” to check the
Internet connectivity again
➢ Select “OptionSettings NetworkInformation”, then press “OK/►” key to display current connection
details, such as Interface, Address type, IP address, etc..

Appendix (10) “How to upgrade Flash SW using Network”

Please follow Appendix (10), make sure your TV is connected on the internet.
 Update through the menu
➢ Select “Option SettingsSupportSoftware updateBy network”, then TV starts to search new
software automatically .If new software is detected, the page will show the button and hint that can guide you.

Page 19 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

note⑪: You can select “Later” if you don’t want to download software now.

➢ Select “Download”, software will be download automatically. The download progress will be shown in the
lower right corner:

note⑫: Please follow the instructions on TV if download or update failed. And you can check your network and

try again.
➢ Please wait for a moment, when the progress appears from 0% to 100%, TV will show a dialog to ask you if
you want to update.

Page 20 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

note⑬: You can select “Later” if you don’t want to update now. While you select “Never”, the dialog will not be

shown until another new software is detected.

➢ Select “Update”, TV will update automatically. First the following dialog will be shown. Then TV will restart
automatically to finish updating:

note⑭: Please do NOT power off TV until it restart successfully.

You can select “Option SettingsSupportSoftware update”, the “Current version” shows the new
Software version.

 Update through auto detection

➢ When your TV has powered on and connected on the internet, a dialog will appear on TV if TV detects new

Page 21 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

software:

note⑮: You can select “Later” if you don’t want to download software and if you select the “Never”, the dialog

will not be shown until another new software is detected.

➢ Select “Download” and TV will download automatically;

➢ All the following operation is same as “Update through the menu”.

Appendix (11) “Factory Menu Description”

1-Factory Hotkey submenu

Item Sub-item Value Note
Enable Hotkey flag by pressing
“◄►” key to have possibility to
access Factory menu with
Hotkey Off/On
“RETURN” key（ ） (default is
disabled)

2-Warm-Up Mode submenu

Item Sub-item Value Note
Enable Burning mode by pressing
“◄►” key, then press “EXIT” key to
Burning
Off/On activate it
Mode
Press “Menu” key on local
keyboard to exit the Burning mode

Page 22 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

3- Reset Shop submenu

Item Sub-item Value Note
Press “OK►” key to remove
Factory presets (channel Maps,
Reset
> bargraph context…) and restore
Shop
User OOB settings. All
adjustments are not impacted!

4-White Balance submenu

Item Sub-item Value Note
HDMI/TV
Source Cannot be Selected
AV/CMP
Standard
Color Temperature Warm Select Tone by pressing “◄►” key
Cool
Set R Gain by pressing “◄►” key
R Gain 000..255
(-128..+127 for offset)
Set G Gain by pressing “◄►” key
G Gain 000..255
(-128..+127 for offset)
White Set B Gain by pressing “◄►” key
B Gain 000..255
Balance (-128..+127 for offset)
Set R Offset by pressing “◄►” key
R Offset 000..255
(-128..+127 for offset)
Set G Offset by pressing “◄►” key
G Offset 000..255
(-128..+127 for offset)
Set B Offset by pressing “◄►” key
B Offset 000..255
(-128..+127 for offset)
Press “►” key to initialize RGB
White Balance Init >
Gain/Offset values
Picture Related > Press “►” key to activate submenu

Dynamic Contrast On/Off Press “◄►” key to enable/disable

Light Sensor On/Off Press “◄►” key to enable/disable
Set Backlight by pressing “◄►”
Back light 000..100
key
0
1
Dynamic Backlight control Select by pressing “◄►” key
2
Picture 3
Related Off Press “◄►” key to enable/disable
Energy Save Low
High
Set APL1_VAL by pressing “◄►”
APL1_VAL 000..100
key
Set APL1_BL_VAL by pressing
APL1_BL_VAL 000..100
“◄►” key
APL2 000..255 Set APL2 point value by pressing

Page 23 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

“◄►” key
Set B point value by pressing
BP 000..100
“◄►” key
Set K value by pressing “◄►”
K 000..100
key

5- Other submenu
Item Sub-item Value Note
Select watch dog ON or OFF by
WatchDog Watch dog ON/OFF
pressing “◄►” key
Upgrade Press “OK►” key to active CI+ key
CI+ Update CI+ Credential >
Credential
Select Project ID by pressing
Project ID ***
“◄►” key
Name *** Info
Panel *** Info
Project ID
RCU *** Info
Region *** Info
PSU *** Info
Running Time *** Info
Select Grey Ctrl ON or OFF by
Grey Ctrl Grey Ctrl *** pressing “◄►” key to control
picture menu Grey or not
Press “OK►” key to remove CI+
Update CI+ Credential >
key
Update
Press “OK►” key to copy CI+ key
CI+ Update from USB >
from USB
Credential
Press “OK►” key to remove CI+
Erase CI+ Credential >
key

Update MAC address > Press “►” key to activate submenu

IPTV
Client Type *** info

Motion
*** *** Motion clarity switch
clarity
ESN ESN Number *** ESN Number info.
CI+Key CI+Key status info. *** info

6-NVM Reset submenu

Item Sub-item Value Note
Press “OK►” key to default NVM
according to selected Project ID
Reset ALL > (all adjustments are defaulted,
channel Maps are cleared, Hotkey
is enabled, …)

7-Preset Factory Channel submenu

Item Sub-item Value Note

Page 24 of 25
 新建文件夹 (3)Test and Alignment Specification for NT63 Series (v0 01) 170612

Preset
Factory *** Preset TV Channel
Channel
8-Power on Mode submenu
Item Sub-item Value Note
Select starting sequence by
pressing “◄►” key
ON
Power on - ON: Force TV to start
STB
Mode -STB: Force TV to standby
LAST
- Last: Force TV to standby or to
start depending on latest operation

9-USB Clone && Update submenu

Item Sub-item Value Note
Press “OK” to update Main
Main Upgrade
software
Press “OK” to update FRC
FRC Upgrade
software
Press “OK” to copy FRC software
FRC Backup
to USB
USB ALL Press “OK” to copy USB template
Clone && All Clone: USB TO TV UserData context to TV depending on
Update CH list Cloning mode
ALL Press “OK” to copy TV template
All Clone: TV TO USB UserData context to USB depending on
CH list Cloning mode
ESN Key Upgrade Press “OK” to upgrade ESN Key
Press “OK” to upgrade HDCP2.0
HDCP2.0 Upgrade
Key

Note⑯: A quick access to suitable submenu item can be achieved by pressing it prefixed RCU key number (ex:

pressing “8” to directly highlight “USB Clone” item).

Page 25 of 25
 12 11 10 9 8 7 6 5 4 3 2 1

H
P100 H
10 KEY

9 LED
STBC_3V3
8

1
KGND

T
7 IR
IR_STB KEY LED IR

2
6 IR3V3SB T T T T R115
1 1 1 1 10K
5 L103

GND
IR3V3SB 220R

1
1 2 STBC_3V3
4 L+
IR R116 INT_IR
1 470R 2
3 L-
2 R-
L101 AMP_VCC LED R117 LED_OUT
1 1K 2
12V_IN 1 2
1 R+
220R
L100 12V_M KEY

2
1 2
220R
C116 L102
0.01U 1 2

2
NC/ 220R C110 C111 C112

1
NC/
5V 330P 330P 0.01U
T

1
1
G LD1
GND G
1 2 WIFIVCC
4.7UH
@Max2.8A
CD5
2 1
0.1U
GND

2
6 1 CD6 CD7
LX BS RD5A CD8 CD9 CD10
NC/
33K 22P 10U 10U 10U 0.1U
(Vin=4.5V-18V) 5 2

GND

1
12V_M IN UD1 GND STBC_3V3

2
2
2

SY8113B
2

CD2 CD3
RD1A 4 3 Vref=0.6V
47K EN FB D101
10U 0.1U Fsw=500KHz

GND
EN=1.5V(on),0.4V(off) 2 1

1
1

RD3A 1 GND R118

WOL 1 1K 2 RD6A NC/ESD5451R
1 4K7
3K6
2

GND RD2A R119

2
CD4 KEY 1 KEY_IN

2
22K 2
10K 1
0.01U

2
RD7A STBC_3V3
750R C114
1

2
0.1U
GND

1
2

E LMBT3906LT1G
GND R104 GND
POWER-ON
H: OFF
L: ON
2 10K 1 B
C
Q100 1
T PW_ON

POWER_ON
KEY voltage F
F
Max V FLOAT MENU/STB CH- CH+ V- V+

1
2
C102 R105
220R
0.01U 2.80V 2.80V 0V 0.582V 1.040V1.542V 2.028

2
3.30V 3.30V 0V 0.671V 1.204V1.794V2.370V
GND
STBC_3V3
T
LDC1 1

2
CDC5
1
1
4.7UH
2 STBC_3V3
@Max2.8A * 0.430V
AD:33
0.980V 1.490V 2.030V 2.660V
AD:76 AD:115 AD:157 AD:206
0.1U Use This New Voltage for NT72563
1

2
6 1 CDC6 CDC7
LX BS RDC5 CDC8 CDC9 CDC10
NC/
27K 22P 22U 22U 22U 0.1U
(Vin=4.5V-18V) 5 2
GND

1
12V_M IN UDC1 GND
2
2

SY8113B
2
2

CDC2 CDC3
RDC1 4 3 Vref=0.6V
EN FB
10U 0.1U 47K Fsw=500KHz
EN=1.5V(on),0.4V(off)
1
1

GND
1

RDC6
E 5K6 E
1

GND CDC4
RDC2
2

10K 0.01U
1
2

RDC7
2

330R
(Vin=4V-23V) CDF6
12V_M 2 1
GND 0.1U
2

2
CDF1 CDF2 CDF3
UDF1

1
GND
10U 10U 0.1U
CORE0V9

IN4

IN3

IN2

IN1

BS
1

1
T
1
20 LDF1 0.68UH
6 LX1 LX3 1 2 CORE0V9

1
RDF1 @Max6A
GND 19

2
100K 7 GND1 LX2 @ 0.97V
CDF8 CDF9 CDF10 CDF11 CDF12
NC/ 18

GND

GND
8 GND2 GND3 22U 22U 22U 22U 0.1U

1
17 CDF7
R01E 9 PG VCC 1 2
R01C 2U2
WIFIVCC NC/0R 2 MAIN5V STBC_3V3 1 NC/0R 2 3V3WIFIVCC 16
1 NC1 NC2
USE WHEN 3V3WIFI ENABLE IS OK 10 GND

TEST

1
ILMT

BYP

1
CDF13

FB
EN
RDF4
33K NC/
STBC_3V3 3V3WIFIVCC
D
S

WIFIVCC MAIN5V
D
S

Q10C PMV65XP Q10E SYT286A 220P

11

12

13

14

15
NC/PMV65XP
2

2
2
2

C15C C15E RDF2

1 2 EN=1V(on),0.4V(off) Vref=0.6V
POWER_ON 3K3
G

D D
G

1U NC/1U GND Pseudo Fsw=600KHz

1
1
1

1
2

1
2

2
CDF4 ILMT=0, 7.8A CDF5 RDF5
R32C R32E RDF3 ILMT=float, 10.3A 1U 51K
22K 0.01U 47K
2
2

NC/22K ILMT=1, 13.3A

2
R22E

2
R22C
1

1
1

1
22K
NC/22K RDF6
GND
1
1

GND 0R
C

4
C
R06C R06E 2

4
1 2 B Q02C WOL 1 2 B Q02E UD25
CORE0V9 4K7

GND/ADJ
BT3904 NC/4K7 GND
E NC/BT3904
2
2

MAIN2V5

OUT
E AS1117-2.5
C07E

VIN
C07C
T
NC/0.1U

1
1U 1
1
1

MAIN5V MAIN2V5

2
1
GND GND C50D C51D C53D
10U 0.1U 10U

1
2
GND GND GND GND
THIS DRAWING CANNOT BE COMMUNICATED TO UNAUTHORIZED PERSONS COPIED UNLES S PERMITTED IN WRITING

C RDJ1 RDJ5 C
1NC/100K
2 220R 1 STR_EN
2
CDJ7 0.01U
2 1 MAIN1V5
UDJ1
LDJ1 T
RT8096A 2.2UH GND 1
(Vin=2.5-6V)
STBC_3V3 VIN LX 1 2 MAIN1V5
CDJ1 CDJ2 4 3
CDJ5 @Max1A
10U 0.1U Fsw=1.5MHz CDJ4
2
2

0.1U

2
22U

2
GND

2
2 CDJ6 RDJ4
GND 22P 100K
Vref=0.6V
1
1

1
FB EN

1
5 1

2
1
EN=1.5V(on),0.4V(off)
GND GND
2

RDJ2
MAIN3V3 33K
T
1

1
2

STBC_3V3 MAIN3V3
D
S

Q10B PMV65XP RDJ3

33K
2

C15B
G

1U
1

GND
2

B R32B
22K
2

R22B
1

22K
1

C
R06B Q02B
1 2 B
CORE0V9 4K7
LMBT3904LT1G
2

E
C07B
0.1U
1

GND
SBU :
TCLNO: .............
TCL Thomson Electronics Singapore Pte. Ltd.
A 8 Jurong Hall Road #28-01/06 A
The JTC Summit SINGAPORE 609434
DESIGNATION Tel (65) 63092900 Fax (65) 63092999

Index-Lab DATE NAME DESCRIPTION Last modif DRAWN CHECKED PAGE:

DESIGNATION ON: ON:
Last saved : BY: BY: OF :
12 11 10 9 8 7 6 5 4 3 2 1

FORMAT DIN A1
 US1
CVBS_RIN D21 Y9 I2S_MCLK
ADIN_R0 GPD_12/I2S_OUT_A_MCLK
W9 I2S_BCLK
US1 CVBS_LIN D22
GPD_11/I2S_OUT_A_BCLK
V9 I2S_LRCK
ADIN_L0 GPD_10/I2S_OUT_A_WS
U9 I2S_DATA
GPD_9/I2S_OUT_A_DATA
K18 E21
VGA_R ADIN_R1
L18 J16 E22
VGA_G TVDAC_OUT ADIN_L1
T10
GPD_27/SPDIF_IN
K23 U10 SPDIF_OUT
SOG_1 GPD_28/SPDIF_OUT
K21
SCART1_R_PR
L19
VGA_B
SCART1_G_Y
L21
DACOUT_R0 A23
DACOUT_R0
NT72563M2
J18
K19
VGA_HS
VGA_VS
SOG_0
M22
DACOUT_L0 B22
DACOUT_L0
AUDIO/IF
M21
SCART1_B_PB
B23 G22 S2_IP
DACOUT_R1 SI+
J21
SCART0_Y
CVBS_VIN J23
CVBS0 C22 G21 S2_IN
DACOUT_L1 SI-
K20
SCART0_FB
H21 G23 S2_QP
TUNER_CVBSIN
NT72563M2 H22
SQ+
S2_QN
F21
R269
ADC/DAC CVBS_OUT AVOUT SQ-

T
C246 0.047U
GND
1 2 J22
100R

1
1 2 ADC0M
C21
AUD_VRM
K22
ADC1M
D23 F23 VIFP
AUD_VRP DEMOD+
L22
ADC2M
C23 F22 VIFN
AUD_VCM DEMOD-
M23
ADC3M
NT72563
NT72563
C275 C273

2
C274 C272
2U2 0.1U2U2 0.1U

1
L200 120R

GND
1 2

GND
1

R223
HP AMP
HP Out 2
4K7
R222
HP_MUTE 1 2 GND
10K
R218
2 33K 1

2
C220 C222
150P 1U
close to SOC GND
R214 R216 R219

1
HPR HP_L C286 2U2

1
1 MIC DACOUT_L0 1 470R 2 8K2 1K
P201 1 2 2 1 2 1
T
3 AU-R
1 R212
HP_R_OUT

2
2 10R 1 C228 C288
5RESERVED
3300P 1500P

7
HPL

1
6 HP-DET R213
HP_L_OUT

RINP

RINN

OUTR

GND1

MUTE

VSS

CN
T 10R
1 2 1 HP_L_OUT
4 AU-L
GND GND
1

1
2

2
2 GND HPGND C283 C214 U200 C223
R210

R211

AD22653 HP_R_OUT
1K

1K

MAIN5V 1U MAIN3V3
1T

HPDET 0.1U 0.1U

10 GND2
OUTL
LINN
LINP
GND
1

UVP
T
2

VDD

1
8 CP
R207 1
1 100K 2

14

13

12

11

9
E

2
R206 GND GND
1 Q200 C225 C226
2 33K R220
B LMBT3906LT1G
2 1K 1 0.1U 22U
C R208 Close to SOC

1
GND

1
1 4K7 2 HP_DET 12V_IN
C221
HP_NC:H
1

150P
2

HP_IN:L GND GND

C280
R209
10K

R215 close to SOC

2
R217 R221
0.1U 1 HP_R C287 2U2
DACOUT_R0 470R 2 1 2 2 8K2 1 2 33K 1
1

1
2

2
R229

2
C285 C219 47K
GND
3300P 1500P
R224

1
2
1 47K 2
1

2
GND GND R228
C224
5K6 1000P

1
2

GND GND

AV Mini IN
SPDIF
MAIN3V3
C247 180P
CVBS 1 1 2 R267
P202 CVBS CVBS 0.33UH C244 0.047U CVBS_VIN
1 2 1 100R 2 1 2
R 2 RIN R200
L402 cloce to SOC 3V3-S
RIN 1 10K 2 C277 2U2 CVBS_RIN SPDIF T
1 2
1
GND 3 T T GND-S P200
AV-GND 1 1
1T

R205 GND2
L 4 R201 1 2 5 TX
GND LIN LIN GND C276 2U2 CVBS_LIN SPDIF_OUT 33R VIN
1 10K 2 1 2 3 IC
VCC
5 2 DRIVE
1

C278 GND LED

2 close to SOC 1

2
GND1
1

C279 4
2

2
2

47P
C248 C249 R225 R230 R202C240 C241
2

75R 10K 10K 470P 0.1U

100P 100P 470P

1
D400 GND
1

1
1

1
CVBS
CVBS 2 1
1 T1 T1 T

RIN
RIN GND
LIN
LIN
ESD5451R GND GND GND
Tuner

MxL661 Tuner TU_3V3

2
VDD_1V8
RT3
100K
CT14

2
GND 0.01U

1
X16M
CT13 1U GND 1 2

1
2 1
16M

24

23

22

21

20

19
UT1

2
TU_3V3 MAIN3V3

AS

XTAL_N
RESET_N

VDD_1P8C

GND_XTAL

XTAL_P
LT5

2
2
GND 33NH
CT2 RT52 RT53

1
5P6 CT6 0.1U 1 18 1K5 1K5

GND
CT22 1 2 1 2 VDD_3P3A CLK_OUT
8.2NH TU-SDA1

1
1
1 2 17 RT16
1 100R
2 LT10 1000R
S1 1 2 1 2 CT4 1000P LNA_INP SDA 1 2 TU-SDA
CT3 1000P LT2 1 2
33NH CT5 1000P 75 OHM Line 3 16 RT15 100R TU-SCL1 LT11 1000R

2
LT1 1 2 1 2 LNA_INN SCL 1 2 1 2 TU-SCL
2 3 CT18
GND1 0.33UH NC/ LT6 TU_3V3
VDD_1V8
2

4 15
2

3 1 2 VDD_IO

2
GND2 2P2 1 2 VDD_1P8A CT33 CT34
4 1000R CT35 CT36

IF_OUTN_2/GPO_2
GND3 FT1

IF_OUTP_2/GPO_1
1
5 14

GND
5 DT1 GND_DIG

2
GND4 AGC_2/GPO_3 22P 22P 22P 22P
6 0BAV99 CT12 Close to SOC
1

GND5 6 13 CT16

1
GND
1

IF_OUTN_1
IF_OUTP_1
0.1U

VDD_1P8B
AGC_1 VDD_1P2

VDD_3P3B
GND6 0.1U

1
TUN1

1
GND GND GND GND

1
GND GND CT7 CT15
GND GND
1800P
MXL661:I2C address:0xC0 0.1U

1
MXL661

10

11
9

12
VDD_1V8 GND
GND

2
2
CT19 CT17
RT7 1U
100R TU_3V3 0.1U

1
1
1
GND Close to SOC
4
4

CT10 0.1U TUNER_FAT+ RT8 1000R RT50

1 0R
2 VIFP
GND/ADJ

1 2 1 2
UD33
TU_3V3
OUT

CT11 0.1U TUNER_FAT- RT9 1000R RT51 0R

VIN

AZ1117 TU_3V3 1 2 1 2 1 2 VIFN

T

2
3

1
CT8 CT9
L001 33P 33P CT52 CT53
MAIN5V 1 2 TU_3V3
120R NC/22P NC/22P
1

1
2

2
1

C150 C151 C153 CT50

0.1U
10U 0.1U 10U
2
1

1
2

GND GND
GND
GND GND GND GND

Close to SOC
RT33
1 10K 2 IFAGC-T

2
CT21
0.1U

1
GND
 AMP AD72587

MAIN3V3

POWER_ON RA01
1 2
10K

1
LA02

2
AMP_RESET 1 RA03 AMP_VCC

2
22UH

RA99

RA98
4K7
4K7
100R 2 CA02 1 2
1 0.1U
2

2
RA02 CA01

2
1
CA23

1
4K7 1000P 0.1U
AMP_SDA

2
GND UA01
1

1
2 AD82587D

1
CA14 CA22 AMP_SCL
0.1U 0.22U L+ L-
GND 1 24

2
PD VDDLA CA24 T T

2
0.1U GND 1 1
2 23
ERROR NC2
GND

1
3 22 L+
SDATA LA LA03
IIC Addr:0X60 22UH L-
4 21

GND
LRCIN GNDL 1 2

RA04
1 2100R 5 20
AMP_SDA SDA LB
White
RA05
1 2100R 6 19 CA15 0.47U
AMP_SCL SCL VDDLB 1 2
22PNC/ CA03
22P NC/ CA04
2

7 18 CA16 0.47U
RESET VDDRB 1 2
R- R+
8 17
VSS RB GND T T
RA06 LA04
1

1 1 AMP_VCC
I2S_DATA 9 16

GND
1 100R 2
VDD GNDR 22UH R-
1 2

1
RA07
I2S_LRCK 1 100R 2 10 15 CA11 CA12 CA13
SA0 RA R+ 4U7 4U7 4U7
RA08 GND

2
I2S_MCLK 1 2 11 14 CA26
100R MCLK NC1

2
0.1U
I2S_BCLK RA09 12 13 Red
1 100R 2 BCLK VDDRA

1
15P CA05

15P CA06

15P CA07

15P CA08

1
GND
2

CA25
2
0.22U
CA17
NC/

NC/

NC/

NC/

2
0.1U

2
CA27 GND
1

0.1U
LA01
MAIN3V3 LA05

1
1 2
120R GND 22UH
2

CA09 1 2
GND CA10
1U
Close to SOC 16V
0.1U
1

GND
 R599
2 1 RXA2+
2R2 R588
2 1 RXB2+
2R2
R598
2 1 RXA2-
HDMI1 2R2 R587
2 2R2 1 RXB2-

10
U517
1
R597
2 2R2
R596
1 RXA1+
RXA1-
HDMI2&ARC U516 R586
2 2R2 1 RXB1+
NC4 LINE1 2 2R2 1 10 1 R585 RXB1-
P501 P502 NC4 LINE1 2 2R2 1
9 2
NC3 LINE2 9 2
1 NC3 LINE2
RX2+ 1
8 3 RX2+

GND

GND
GND2 GND1 8 3

GND

GND
GND1 2 GND2 GND1
GND1 2
7 4
NC2 LINE3 7 4
3 NC2 LINE3
RX2- 3
6 5 RX2-
NC1 LINE4 6 5
RX1+ 4 NC1 LINE4
RX1+ 4
5 AZ1045-04F AZ1045-04F
GND2 5
GND2
RX1- 6
RX1- 6
7 R595
2 2R2 1 RXA0+
RX0+ 7 R584
2 2R2 1 RXB0+
R594 RXA0- RX0+
2 2R2 1 R583 RXB0-
GND3 8 2 2R2 1
GND3 8
U515 R593
2 1 RXAC+
9 2R2 U514 R582
2 1 RXBC+
RX0- 10 1 9 2R2
NC4 LINE1 R592 RXAC- RX0- 10 1
2 2R2 1 NC4 LINE1 R565 1 RXBC-
RXC+ 10 2 2R2
9 2 RXC+ 10
NC3 LINE2 9 2
NC3 LINE2
11 8 3

GND

GND
GND4 GND2 GND1 11 8 3

GND

GND
GND4 GND2 GND1
RXC- 12 7 4 D599
NC2 LINE3 AZ5725-01F RXC- 12 7 4 D594
HA_SCL NC2 LINE3 AZ5725-01F
13 CEC 1 2 HB_SCL
NC1 6 5 13 CEC 1 2
NC1 LINE4 NC1 6 5
D598 NC1 LINE4
NC2 14 AZ5725-01F D593
AZ1045-04F HA_SDA NC2 14 HDMI_ARC AZ1045-04F AZ5725-01F
1 2 HB_SDA
15 HA_SCL HA_5V HB_5V 1 2
DDCCLK 15 HB_SCL
DDCCLK
DDCDA 16 HA_SDA HA_HPD
1 2 DDCDA 16 HB_SDA HB_HPD
ESD5451R 1 2
17 D564 ESD5451R
GND5 17 D592
GND5

2
2
R504 CEC

2
2
VCC 18 HA_5V 1 2 PWR5V_A R502 R501 R526 HDMI_ARC
4K7 1 2 VCC 18 HB_5V 1 2 PWR5V_B R522 R521
47K 47K D597 4K7 1 2
ESD5451R D591
2

19 HA_HPD 47K 47K

1
2

ESD5451R

2
HPD 19 HB_HPD

1
2
R551 R503 R505 R590 HA_5V HPD

1
1
HDMIA_SCL R523 R515 R527 R580 HB_5V

1
1
1K 10K 10K 1 100R 2 1 2 HDMIB_SCL
GND 1K 10K 10K 1 100R 2 1 2
R589 ESD5451R D596 GND
HDMIA_SDA R579 ESD5451R D590
1

GND
2
1

1 100R 2 HDMIB_SDA

1
GND

2
1
1 100R 2
C R506
HDMIA_DET GND C R525
2 100R 1 HDMIB_DET GND
Q506 B 1 2 2 100R 1
10K Q507 B 1 2
BT3904 10K
R508 BT3904
E C R524
R500 E C
Q500 B 1 2 STBC_3V3 R510
10K Q501 B 1 2 STBC_3V3
GND BT3904 10K
GND BT3904
E
E

GND
GND

US1
AC17
RXC_CLK-
W16 AB17
STBC_GPI_15/MHL_CBUS RXC_CLK+
AA18
RXC_0-
NT72563M2 RXC_0+
RXC_1-
AB18
AA19
RXAC-
RXAC+
AA11
AC11
RXA_CLK- HDMI/MHL RXC_1+
AB19
AC19
RXA_CLK+ RXC_2-
RXA0- AB11 AA20
RXA_0- RXC_2+
RXA0+ AB12 AB20
RXA_0+ PWR5V_C/STBC_GPI_4
RXA1- AA13
RXA_1-
RXA1+ AB13
RXA_1+
RXA2- AC13
RXA_2-
RXA2+ AA14 W17 HDMIA_SCL
RXA_2+ HDMIA_SCL/STBC_GPF0
PWR5V_A AC20 Y17 HDMIA_SDA
PWR5V_A/STBC_GPI_16 HDMIA_SDA/STBC_GPF1
V17 HDMIB_SCL
HDMIB_SCL/STBC_GPF2
Y18 HDMIB_SDA
HDMIB_SDA/STBC_GPF3
W18
R581 HDMIC_SCL/STBC_GPF4
HDMI_ARC 1 2 Y14 Y19
51R HDMI_ARC HDMIC_SDA/STBC_GPF5

RXBC- AC14
RXB_CLK-
RXBC+ AB14
RXB_CLK+
GND

RXB0- AA15 Y16

RXB_0- MHL_CDS/STBC_GPG_24
RXB0+ AB15
RXB_0+
RXB1- AA16
RXB_1-
RXB1+ AB16
RXB_1+ R561
RXB2- AC16 V16 1 2 CEC
RXB_2- HDMI_CEC/STBC_GPG_31 100R
RXB2+ AA17
RXB_2+
PWR5V_B AC21
PWR5V_B/STBC_GPI_17
R562 D511 1N4148WS
NT72563 1 27K 2 STBC_3V3
K A
 LVDS Out FHD/HD 60Hz

US1
TXO0-
TXO0+
A6
B6
LVO_0-
LVO_0+
NT72563M2LVE_0-
LVE_0+
C10
B11
TXE0-
TXE0+
TXO1- C6
B7
LVO_1- LVDS LVE_1-
A11
C11
TXE1-
TXO1+ LVO_1+ LVE_1+ TXE1+
C7 A12
TXO2- LVO_2- LVE_2- TXE2-
B8 B12
TXO2+ LVO_2+ LVE_2+ TXE2+
No. FFC PIN NAME MCU A8 C12
PANEL_VCC TXOC- LVO_CLK- LVE_CLK- TXEC-
1 PANEL_VCC C8 B13
1 TXOC+ LVO_CLK+ LVE_CLK+ TXEC+
2 PANEL_VCC A9 C13
2 TXO3- LVO_3- LVE_3- TXE3-

2
3 PANEL_VCC C626 B9 B14
3 TXO3+ LVO_3+ LVE_3+ TXE3+
4 PANEL_VCC C9 A14
4 0.1U TXO4- LVO_4- LVE_4- TXE4-
5 NC B10 C14
5 TXO4+ LVO_4+ LVE_4+ TXE4+

1
6 GND 6
7 GND 7 12V_M PANEL_VCC

D
S
8 GND NT72563 Q600 PMV65XP
8 GND E4+ TXE4+ @Max3A

T T T T T T T T T T T T T T T T T T T T T T T T
9

2
NC 9

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
E4- TXE4-
10 LD_EN OUT 10 TXE4+ R600

G
E3+ TXE3+
11 TXE4+ 11 TXE4- 47K
12 TXE4- E3- TXE3-
12 TXE3+
EC+ TXEC+

1
13 TXE3+ 13 TXE3-
14 TXE3- 14 EC- TXEC-
15 E2+ TXE2+ C
GND 15 TXEC+ R604 Q601
16 TXEC+ 16 TXEC- E2- TXE2- PANEL_ON 1 4K7 2 B
17 TXEC- 17 E1+ TXE1+ P802 LMBT3904LT1G
18 GND 18 TXE2+ E1- TXE1- 1 E
C618 0.1U

2
1 GND

2
19 TXE2+ 19 TXE2- E0+ TXE0+ 2 C617 1 2
20 TXE2- 2 NC R607
20 TXE1+ E0- TXE0- 3

2
21 TXE1+ 3 NC 3K3 0.1U
21 TXE1- O4+ TXO4+ 4 NC 4 R608
22 TXE1- 22 TXE0+ 5

1
O4- TXO4- 2K7

1
23 TXE0+ 5 GND TXE3+
23 TXE0- 6
24 TXE0- 03+ TXO3+ 6 TXE3+ TXE3-
24 7

1
25 3D_LR_OUT PWM O3- TXO3- 7 TXE3-
25 8 GND 8
26 3D_EN OUT 26 TXO4+ OC+ TXOC+ 9 TXEC+ GND GND
27 TXO4+ 27 TXO4- OC- TXOC- 9 TXEC+ 10 TXEC-
28 TXO4- O2+ TXO2+ 10 TXEC-
28 TXO3+ 11
29 TXO3+ 11 GND TXE2+
29 TXO3- O2- TXO2- 12 TXE2+ 12
30 TXO3- 30 O1+ TXO1+ 13 TXE2-
31 GND 13 TXE2-
31 TXOC+ O1- TXO1- 14
32 TXOC+ 14 GND
32 TXOC- O0+ TXO0+ 15 TXE1+
33 TXOC- 15 TXE1+
33 O0- TXO0- 16 TXE1- 16 TXE1-
34 GND 34 TXO2+ 17
35 TXO2+ 35 TXO2- 17 GND 18 TXE0+
36 TXO2- 18 TXE0+ TXE0-
36 TXO1+ 19
37
38
TXO1+
TXO1-
TXO0+
37
38
TXO1-
TXO0+ LVDS Test Point 19 TXE0-
20 GND
21 NC
20
21
P_GND

T
39 39 TXO0- 22 LVDS_SEL
22 LVDS_SEL

1
40 TXO1- 40 23
41 GND 23 NC GND
41 24 GND 24
42 NC 42 25 LVDS_SEL
NC GND 25 GND L-SEL

T
43

2
43 26 C627
26 NC

1
44 LG_DIM PWM 44 LVDS_SEL 27 GND

1
45 LVDS_SEL 27 PANEL_VCC
45 28 PANEL_VCC 28 0.1U R605
46 3D_FORMAT1 OUT 46 29

1
47 3D_VSYNC_IN IN 47 29 PANEL_VCC 30 PANEL_VCC
100R
48 3D_FORMAT0/SDA/WP OUT 30 PANEL_VCC
48

2
49 SDA/SCL/WP OUT 49 1 1
50 SCL OUT
50 T T
GND
51 NC 51 PANEL_VCC
P601
HD PANEL_VCC1

FHD
 RJ45 Jack
ETHERNET_TD+ 1 RN1A
2R2 2 CN6 NC/
ETHERNET_TD- RN2A 1 210P
1 2R2 2
TS8121CLF
UN1
TX1P
LINE4 NC1
5 6 8 9
RN5 RN7
LINE3 NC2 1 75R 2 1 75R 2 TXC
4 7 7 10
TX1N
GND

GND
Must be differential 100ohm GND1 GND2
3 8 6 11
LINE2 NC3
2 9 5 12
LINE1 NC4
1 10 4 13
ETHERNET_RD+ 1 RN3
2 ESD RX1P
2R2 3 14
RN6 RN8
CN7 NC/ 1 CN4 0.1U 1
210P 75R 2 1 2 75R 2 RXC
1 2 15 1
ETHERNET_RD- 1 RN4
2 RX1N
2R2 1 16 CN3

2
ESD5451R 1000P

2
UN2
CN5 CN1A CN2
2 PN1
DN1 1000P 0.1U 0.01U
GND 11
1

1
12
1

GND
TX1P 1
TX1P

T
TX1N 2

1
GND TX1N

T
RX1P 3

1
RX1P

T
TXC 4

1
TXC

T
5

1
RX1N 6
RX1N

T
RXC 7

1
RXC

T
8

1
9

10

GND
 MAIN1V5

N9
N1

H9
H2
R9
R1

K8
K2
G7
D9
B2

D2
C9
C1
E9
F1

A1
A8
U12
US1

VDD
VDD7
VDD2
VDD1
VDD3
VDD8
VDD4
VDD5
VDD6

VDDQ4
VDDQ3
VDDQ2
VDDQ5
VDDQ6
VDDQ1

VDDQ7
VDDQ8
VDDQ
DDRS_A0 AC2 L3 DDRS_DQ0
MA0 DQ16
DDRS_A1 AA5 P1 DDRS_DQ1 DDRS_A0 N3 1 2 3 7 8 9 D3 DDRS_DM1
MA1 DQ17 A0 DMU
DDRS_A2 AC3 K2 DDRS_DQ2 DDRS_A1 P7 A C7 DDRS_DQS1
MA2 DQ18 A1 DQSU
DDRS_A3 Y2 R3 DDRS_DQ3 DDRS_A2 P3 VDDQ DQU5 DQU7 DQU4 VDDQ VSS B7 DDRS_DQS1B
MA3 DQ19 A2 DQSU
DDRS_A4 U4 J1 DDRS_DQ4 DDRS_A3 N2 B
MA4 DQ20 A3
DDRS_A5 W2 T3 DDRS_DQ5 DDRS_A4 P8 VSSQ VDD VSS DQSU# DQU6 VSSQ D7 DDRS_DQ8
MA5 DQ21 A4 DQU0
DDRS_A6 V5 J2 DDRS_DQ6 DDRS_A5 P2 C C3 DDRS_DQ9
MA6 DQ22 A5 DQU1
DDRS_A7 W3 R2 DDRS_DQ7 DDRS_A6 R8 VDDQ DQU3 DQU1 DQSU DQU2 VDDQ C8 DDRS_DQ10
MA7 DQ23 A6 DQU2
DDRS_A8 W5 DDRS_A7 R2 D C2 DDRS_DQ11
MA8 A7 DQU3
DDRS_A9 V1 N6 DDRS_DQ8 DDRS_A8 T8 VSSQ VDDQ DMU DQU0 VSSQ VDD A7 DDRS_DQ12
MA9 DQ24 A8 DQU4
DDRS_A10 R5 M6 DDRS_DQ9 DDRS_A9 R3 E A2 DDRS_DQ13
MA10 DQ25 A9 DQU5
DDRS_A11 W4 P6 DDRS_DQ10 DDRS_A10 L7 VSS VSSQ DQL0 DML VSSQ VDDQ B8 DDRS_DQ14
MA11 DQ26 A10 DQU6
DDRS_A12 T4 J4 DDRS_DQ11 DDRS_A11 R7 F A3 DDRS_DQ15
MA12 DQ27 A11 DQU7
DDRS_A13 V3 M4 DDRS_DQ12 DDRS_A12 N7 VDDQ DQL2 DQSL DQL1 DQL3 VSSQ
MA13 DQ28 A12 G
DDRS_A14 Y4 K5 DDRS_DQ13
MA14 DQ29
N5 DDRS_DQ14 DDRS_BA0 M2 VSSQ DQL6 DQSL# VDD VSS VSSQ E7 DDRS_DM0
DQ30 BA0 DML
L5 DDRS_DQ15 MAIN1V5 DDRS_BA1 N8 H
F3 DDRS_DQS0
DQ31 BA1 DQSL
DDRS_BA0 AA1 DDRS_BA2 M3 VREFDQ VDDQ DQL4 DQL7 DQL5 VDDQ G3 DDRS_DQS0B
MBA0 BA2 DQSL
DDRS_BA1 T5 J
MBA1
DDRS_BA2 Y1 DDRS_CS0 L2 NC VSS RAS# CK VSS NC E3 DDRS_DQ0
MBA2 CS DQL0 MAIN1V5

1
DDRS_RASN J3 K F7 DDRS_DQ1
RAS ODT VDD CAS# CK# VDD CKE DQL1
R48 DDRS_CASN K3 F2 DDRS_DQ2
DDRS_WEN AB4 L1 DDRS_DQS0 CAS L DQL2
MWE DQS2 1K DDRS_WEN L3 F8 DDRS_DQ3
DDRS_CASN AA2 M3 DDRS_DQS0B WE NC CS# WE# A10 ZQ NC DQL3
MCAS DQS2B DDRS_ODT K1 H3 DDRS_DQ4
ODT DQL4

1
DDRS_RASN AB3 M2 DDRS_DQS1 M H8 DDRS_DQ5
MRAS DQS3 DQL5
DRAM_S_CKE R6 N3 DDRS_DQS1B M8 VSS BA0 BA2 NC VREFCA VSS G2 DDRS_DQ6 R419
MCKE1 DQS3B VREFCA DQL6
DDRS_ODT AB2 N H7 DDRS_DQ7 1K
MODT
DDRS_CKE_F AB6 NT72563M2 J1 VDD A3 A0 A12 BA1 VDD DQL7

1
KGD_CKE0 NC1

2
J9 P H1
1K C68 C67 NC2 VREFDQ
DDRS_CLKN
DDRS_CLK
U3
U2
MCLKB
MCLK
DDR DM2
DM3
P3
K4
DDRS_DM0
DDRS_DM1 R51 1000P 0.1U
L1
L9
NC3
VSS A5 A2
R
A1 A4 VSS
J7 DDRS_CLK
NC4 VDD A7 A9 A11 A6 VDD CK
M7 K7 DDRS_CLKN

2
2

1
NC5 CK

1
DDRS_CS0 AB5 DDRS_A13 T3 R K9 DRAM_S_CKE C321 C320
MCS1 A13 CKE 1K
MMU_RSTN AC5 DDRS_A14 T7 VSS RST# NC NC A8 VSS T2 DRAM_S_RSTN
MRST NC7 RESET R421
DRAM_S_RSTN AC4
RESET_KGD GND 0.1U 1000P
K4B4G1646E

VSSQ1
VSSQ2
VSSQ3
VSSQ4
VSSQ5
VSSQ6
VSSQ7
VSSQ8
VSS10

VSS11
AA6
GND

2
240R

2
ZQ

VSSQ
VSS1
VSS2
VSS3
VSS4
VSS5
VSS6
VSS7
VSS8
VSS9
1 2

VSS
R52

ZQ
1 2 H1
MAIN1V5 1K VREFQ_KGD
P12
R418 VREF GND

L8
T9
T1
P9
P1
M9
M1
J8
J2
G8
E1
A9
G9
G1
F9
E8
E2
D8
D1
B9
B1
B3
1
1

R420 C322
NT72563
1K 0.1U

2
2
2

R50 GND
240R
GND

1
GND

R56
DDRS_CLK MMU_RSTN 2 NC/0R 1 R152
DRAM_S_CKE 2 1 DDRF_CKE
R58 1K2
DDRF_RSTN 2 1 DRAM_S_RSTN
12K

2
R155
MAIN1V5 100R DDRS_CKE_F 2 1
MAIN1V5 1K2

1
R53
R60
1

10U 0.1U 0.1U 0.1U 0.1U 22U 10K

1
10U 0.1U 0.1U 0.1U 0.1U 22U

1
DDRS_CLKN R61 R59
C64 C60 C59 C58 C57 C56

2
C55 C51 C50 C49 C48 C47 1K 1K
2

1
GND

GND

2
GND

GND

DDRS_A0 R425
2 100R 1 VTT_DDRS_A0V75_PW
DDRS_A1 R426
2 100R 1
DDRS_A2 R427

2
2 100R 1
DDRS_A3 R428 1000P 1000P 0.01U 0.01U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 22U
2 100R 1
MAIN1V5 DDRS_A4 R429
2 100R 1 C336 C335 C338 C337 C103 C101 C70 C69 C66 C65 C63 C62 C61
DDRS_A5 R430
2 100R 1

1
R431

GND
DDRS_A6
2

1
2

2 100R
C181 0.1U R184 DDRS_A7 R432
2 100R 1
10K UC1 DDRS_A8 R433
2 100R 1
22U C210 R024 R434
1 8 1 2
DDRS_A9 2 100R 1
VIN VCNTL4 0R STBC_3V3
1

DDRS_A10 R435
1

2 100R 1
R436
1

2 7 DDRS_A11
GND

2 100R 1
GND VCNTL3 0.1U 1U DDRS_A12 R437
2 100R 1
GND 3 6 DDRS_A13 R438
VREF VCNTL2 C189 C182 2 100R 1
DDRS_A14 R439
2 100R 1
2

4 5
2

D VOUT VCNTL1
R187 C186 DDRS_BA0 R440
POWER-ON 1 2 G Q25 R186 2 100R 1
4K7 G2992B DDRS_BA1 R441
2N7002K 10K 1U GND 2 100R 1
S DDRS_BA2 R442
2 100R 1
1
1

VTT_DDRS_A0V75_PW
2

C191 DDRS_RASN R445

GND 2 100R 1
DDRS_CASN R444
2 100R 1
22U
DDRS_WEN R443
2 100R 1
1

DDRS_CS0 R447
2 100R 1
DDRS_ODT R446
2 100R 1
GND
 P20
P19
US1
T T
1 1 R906
P16 P20 2 1
STBC_GPF_6_BS12_ STBC_GPG_27/STBC_UART_1_TX/ARM_UART_B_TX/ARM_UART_A_TX 47K STBC_3V3
BS3 W19 P19 2 1
STBC_GPF_7_BS3_ STBC_GPG_28/STBC_UART_1_RX/ARM_UART_B_RX/ARM_UART_A_RX 47K T
T14
STBC_GPF_8_BS4_ STBC_GPG_29/STBC_UART_0_TX/I2C_M0_SDA/I2C_S_SDA/SD_DAT0
STBC_GPG_30/STBC_UART_0_RX/I2C_M0_SCL/I2C_S_SCL/SD_DAT1
M20
M19
BL_ON
R907 1 BL-ON close to eMMC
eMMC close to eMMC
GND

L14 R20
STBC_GPG_3_BS18_IN_ STBC_GPG_14/I2C_M0_SDA
M14 P18 WIFI_ON
STBC_GPG_4_BS2_ STBC_GPG_15/I2C_M0_SCL UF1 RF13
1 2
LED_OUT R19 V18 SOC_VER_GPIO1 47K EMMC_VDD
STBC_GPG_7/STBC_PWM_BS13_IN_ STBC_GPG_16/I2C_M1_SDA/MPLL_TEST/SD_DAT2 EMMC_CLK RF1
1 2 W6 J3 RF7
1 2 EMMC_D4
BS19 R22 W20 SOC_VER_GPIO2 0R CLK D4 0R
STBC_GPF_10_BS19_
STBC UART/I2C STBC_GPG_17/I2C_M1_SCL/SD_DAT3 EMMC_CMD RF2
1 0R 2 W5
CMD D5
J4 RF8
1 0R 2 EMMC_D5
GND

P13
STBC_GPF_11_BS1_ EMMC_D0 RF3
1 2 H3 J5 RF9
1 2 EMMC_D6
BS9 AB21 AC10 ETHERNET_RD- 0R D0 D6 0R
STBC_GPI_2_BS9_ MDI1N EMMC_D1 RF4
1 2 H4 J6 RF10
1 2 EMMC_D7
T13 AB10 ETHERNET_RD+ 0R D1 D7 0R
STBC_GPI_18_BS20_ MDI1P EMMC_D2 RF5
1 2 H5 R5
U17 AA10 ETHERNET_TD- 0R D2 DS
STBC_GPI_14 MDI0N EMMC_D3 RF6
1 2 J2 U5 EMMC_RSTN
WOL F4 AB9 ETHERNET_TD+ 0R D3 RESET
GND STBC_GPI_13 MDI0P
E_UPGRADE AB23

GND
AB22 1
STBC_GPG_8/SAR_ADC_0 ETH_REXT 12K 2 EMMC_VDD K6 M6

1
R901
KEY_IN
STR_EN
AA23
STBC_GPG_9/SAR_ADC_1 Ethernet VCM_MON
R16
R1025 W4
VDD_IF4
VDD_IF3
VDD3
iNAND
VDD2
N5 CF4
GND

C1
4K7 1 STBC_GPG_10/SAR_ADC_2 Y4 T10

1
2 DDRF_RSTN VDD_IF2 VDD1

GND
W7 T18 CF1 CF2 CF3 NC/1000P
STBC_GPG_11/SAR_ADC_3 _BS15_IN_STBC_GPF_17/SPI_DO_DIO0_ STBC_3V3 AA3 U9
AA22 U18 VDD_IF VDD

2
STBC_GPG_12/SAR_ADC_4/SD_CLK STBC_GPF_16/SPI_DI_DIO1_ 2U2 0.1U 0.1U AA5
HP_MUTE Y21 U19 VDD_IF1
STBC_GPG_13/SAR_ADC_5/SD_CD# STBC_GPF_15/SPI_CLK T5 M7
HP_DET Y22 U20 OPTION1 VSS1

2
STBC_GPG_22/SAR_ADC_6/SD_WP STBC_GPF_14/SPI_CS0 K4 P5 GND
DDRF_CKE VSS VSS2

GND
W21 T19
STBC_GPG_23/SAR_ADC_7/SD_PWEN# _BS8_IN_STBC_GPF_19/SPI_HOLD_DIO3_ Y2 R10
WOL_DET

1
W22 R18 VSS5 VSS3
STBC_GPG_26/SAR_ADC_8/SD_CMD STBC_GPF_18/SPI_WP_DIO2_

GND
GND Y5 U8

R902
VSS6 VSS4

47K
AA4 H6
NT72563M2 eMMCSTBC_GPF_20/EMMC_D0
STBC_GPF_21/EMMC_D1
T21
T22
EMMC_D0
EMMC_D1
P901
AA6
VSS7 OPTION2
VSS8 CREG/VDDI
K2
EMMC3V3

2
STBC

2
T23 EMMC_D2 CF5 CF6 CF7
THGBMFG6C1L

1
STBC_GPF_22/EMMC_D2
STBC_GPF_23/EMMC_D3
U21 EMMC_D3
E_UPGRADE 1 2 CF8 CF9

GND
N22 U22 EMMC_D4 0.1U 0.1U 2U2
STBC_GPG_20/VGA_SDA/I2C_M0_SDA STBC_GPF_24/EMMC_D4 2U2 0.1U
N23 V22 EMMC_D5

1
STBC_GPG_21/VGA_SCL/I2C_M0_SCL STBC_GPF_25/EMMC_D5

2
R23 EMMC_D6
STBC_GPF_26/EMMC_D6 NC/
STBC_3V3 STBC_GPF_27/EMMC_D7
R21 EMMC_D7 GND GND GND
INT_IR V20 W23 EMMC_CLK
STBC_GPF_12/STBC_IR STBC_GPF_29/EMMC_CLK
STBC_RSTN V19 V21 EMMC_CMD STBC_3V3 1 0R 2 EMMC3V3 GND
R910 STBC_RSTN STBC_GPF_31/EMMC_CMD
2 1 POWER-ON AA21 V23 EMMC_RSTN RF28
10K PW_EN STBC_GPG_2/EMMC_RSTN
R903
T12 P21 1 2
T12 STBC_GPF_13/STBC_RSTOUT XTAL_OUT 51R
T

P22 1 2 X12M
R900 0R
1

XTAL_IN
GND

2 1 P17
10K TEST_EN R904

GND
GND1
1 IN/OUT1 2

4
NT72563 IN/OUT2

GND

4
4 GND2 3

GND/ADJ
UD18 EMMC1V8

OUT
12M

VIN
AS1117-1.8
T
1

1
R905
1 1M
2
EMMC3V3 EMMC_VDD

2
1
C905 C906 C01E C04E C05E
12P 12P 10U 0.1U 10U

1
2
Boot Starp GND
GND GND GND GND

Note:Please Check Application Note for Boot Starp pins Advanced Application
Layout Note:Made them on the same area
BS0/4/8/12/15/20=0

RESET(need > 50ms)

STBC_3V3

RBS07 BS3 BBS3 RBS08

2 10K 1 2 NC/10K1

STBC_3V3

RBS19 BS9 BBS9 RBS20

2 10K1 2NC/10K 1

K
RBS23 LED_OUT BBS13 RBS24 DS01
2 NC/10K1 2 10K 1 RS01
BS9=0:w/o Security Boot YUS1 33K
BAS316
BS9=1:w/ Security Boot

A
1
RS02
STBC_RSTN
100R

2
2
2
RBS31 BS19 BBS19 RBS32 67-H93883-3A0
2 10K 1 2 NC/10K1 CS01
CS03
10U 0.01U

1
1
STBC_3V3 GND

2
GND
CS02
10U
RV1
2 10K 1 SOC_VER_GPIO1 RV2
2 NC/10K1

1
RV3
2 NC/10K1 SOC_VER_GPIO2 RV4
2 10K 1

Ver.A:RV1=NC, RV2=10K TUNER IIC=GPD0/GPD1 GND

GND
Ver.B:RV1=10K, RV2=NC TUNER IIC=GPC15/GPC16
 US1
USB_DP0 A20
USB0_D+ R1010
USB_DM0 C20 B1 TXD 2 NC/47K1
USB0_D- GPC_4/ARM_UART_B_TX/INT_5/ARM_UART_A_TX MAIN3V3
C2 RXD 2 NC/47K1
GPC_5/ARM_UART_B_RX/INT_6/ARM_UART_A_RX
USB_DP1 A21
USB1_D+ R1011
USB_DM1 B21
USB1_D-
USB_DP2 AC8
USB2_D+
USBx4 GPC_16/I2C_MD_SDA
GPC_15/I2C_MD_SCL
E1
E2
TU-SDA
TU-SCL
USB_DM2 AA8
USB2_D-

GND
H2
GPC_12/INT_7_BS0_
USB_DP3 AC7 D2
USB3_D+ GPC_13/INT_8
USB_DM3 AB7
USB3_D- NT72563M2 GPC_14/INT_9
D1

USB/GPIO
UART/I2C C3

1 1 1 1 1
ARM_TRST/GPC_11 EJTAG_TRST

T T T T T
J12
ARM_TCK/GPC_7 EJTAG_TCK
H4
ARM_TMS/GPC_8 EJTAG_TMS
D3
ARM_TDI/GPC_10 EJTAG_TDI
A-DIM
P-DIM GPIO ARM_TDO/GPC_9
H3
EJTAG_TDO
T T V13 Delete them before MP
1 GPE_11/CI_HA9/FR_PWM/LED_VS_OUT
1 A22
DIM_PWM W13
GPE_12/CI_HA10/TENSILICA_TCK/USB0_PWEN/AMBI_SPI_DI
GPE_13/CI_HA11/TENSILICA_TMS/AMBI_SPI_DI
ARM UART/I2C/ICE
E3
A_DIM GPE_14/CI_HA12/TENSILICA_TDO/LED_PWM_0/LED_SPI_STT/HSC_SDA
E4
GPE_15/CI_HA13/TENSILICA_TDI/LED_PWM_1/LED_SPI_DI/HSA_SCL
D4
GPE_16/CI_HA14/TENSILICA_TRST/LED_PWM_2/LED_SPI_CLK/LED_YDIO
Y13
AMP_RESET GPE_17/CI_HAD0/I2S_OUT_B_MCLK/LED_PWM_3/LED_SPI_DO
W14
GPE_18/CI_HAD1/I2S_OUT_B_BCLK/LED_PWM_4/LED_SPI_CS_0
V14
USB2.0+RS232 Port U14
GPE_19/CI_HAD2/I2S_OUT_B_WS/LED_PWM_5/LED_SPI_STT/HSC_SDA
GPE_20/CI_HAD3/I2S_OUT_B_DATA/LED_PWM_6/LED_SPI_DI/HSC_SCL

USB5V1
RP1000 T Y6
1 GPD_0/PTSIN1_ERR/STSIN0_ERR/I2C_MA_SDA
1 2
W6
MAIN5V GPD_1/PTSIN1_CLK/STSIN1_CLK/I2C_MA_SCL
V6
P GPD_2/PTSIN1_VALID/STSIN1_VALID/I2C_MB_SDA/PTSIN2_VALID

P
1
U6
C1002 GPD_3/PTSIN1_START/STSIN1_START/I2C_MB_SCL/PTSIN2_START
C1001 AMP_SDA T6
220U GPD_4/PTSIN1_D0/STSIN1_DATA/I2C_MC_SDA/PTSIN2_D0
0.1U AMP_SCL U7
GPD_5/PTSIN1_D1/I2C_MC_SCL/PTSIN2_D1
16V LNB_EN AA9

N
2
D0- D0+ RXD TXD GPD_6/PTSIN1_D2/I2S_IN_DATA/PTSIN2_D2
P1001 LNB_SEL U8
GPD_7/PTSIN1_D3/I2S_IN_WS/PTSIN2_D3
T T T T 9 T9
GPD_8/PTSIN1_D4/I2S_IN_MCLK/DEMOD_QLED/PTSIN2_D4
1 1 1 1
GND 1
R1050
RXD 1 8
470R 2
USB_DM3 1 R1052
2 2
2R2
7
USB_DP3 1 R1053
2 3 IFAGC-S W10
2R2 GPD_13/PTSOUT_CLK/PTSIN2_CLK/DEMODOUT_CLK/RFAGC_VSYNC/S2_AGC
TXD 1 6 IFAGC-T V10
470R 2 GPD_14/PTSOUT_VALID/PTSIN2_VALID/DEMODOUT_VALID/VIF_IF_AGC/DEMOD_IF_AGC/T2_AGC
4 AB8
GPD_15/PTSOUT_START/PTSIN2_START/DEMODOUT_START/DEMOD_EMERGENCY
R1051 DISEQC_OUT
5 U11
1

C1050 C1051 GPD_24/CI_RST/TC_POL1/DISEQC_TX

HDMIA_DET Y10
GPD_26/CI_CE#/BT_SHOP_VS_IN/BT_SHOP_LR_IN
1

HDMIB_DET U12
10P 10P C1054 C1064 GPD_29/CI_IOWR#/ARM_UART_A_TX
10 HDMIC_DET U13
GPD_30/CI_OE#/ARM_UART_A_RX
2

MNT-HOLE1
3P3 3P3
11
2

GND GND MNT-HOLE2

UGND1 NT72563
T
1

GND GND

Wifi Port P1005

BT Port
WIFI-VCC 8
WGND
T WIFI-DM 7
D2+D2- 1
GND

T T WIFI-DP 6
1 1 BTGND
USB_DP2 1 R1054 P1003 T BT5V
2R2 2 WIFI-DP 5 1 T
USB_DM2 R1055 1
1 2R2 2 WIFI-DM WIFI-RST 4 L1000 120R
W_5V 1 2 MAIN5V
1
T

L1001 120R
1

WIFIVCC WIFI-VCC WIFI-DET 3

GND

1 2
NC/L100E 120R 2
3V3WIFIVCC 1 2
1

C1021 C1020 C1055 2 D3- T

WOL 3 T D3+
3P3 3P3 0.01U 1 1 R1038
T 1 1 USB_DM1
2R2 2
R1037 4
2

1
WOL_DET 1 R1056
100R 2 WIFI-DET GND 1 USB_DP1
2R2 2
R1057 R1030 5
2 4K7 1
WIFI_ON
STBC_3V3 1 100R 2 WIFI-RST
1

NC/10K2 WIFION 6
1 P1002
T

R1058
1

C1003 C1004 C1056

2

GND 9
GND

C1027
GND GND 3P3 3P3 0.01U
0.01U WIFI-DP 8
2

2
1

WIFI-DM 7
GND GND
WIFI-VCC 6

WIFI-DET 3

WIFI-RST 2

1
GND

NC/
 MAIN3V3

2
120R
1
L1104

0.1U
C215
1 2

GND
0.1U
1 2
1 2

GND
2U2

US1
C211
C175 C173
10U
1 2

NT72563
VDD33
A1 L13
GND6 VDD25_DLL GND
G18
GND51
G19

MAIN2V5
GND49
G20 E5
GND48 VDD09_DDR
H18

MAIN3V3
GND52
H20

CORE0V9
GND53
J3
GND38
J8
GND7
J9 F3
GND8 VDD15_CLK
J10 G3
GND9 VDD15_MMU2
J14 G4
GND4 VDD15_MMU3
J15
GND33
J20 P11
GND32 VDD15_MMU

DDR
K3 M12
GND43 VDD15_MMU1
K6 F1
GND10 VDD15A_MMU
K14 F2
GND3 VDD15A_MMU1
MAIN2V5

K15 N12
GND24 VDD15A_MMU2
K16
GND55
L2 N11 GND
GND25 VDD15_LDO
L6
GND39
L15
10U

GND28 1 2
L16 G1
GND34 VDD15_KGD
L17 G2
GND VDD15_KGD1
M1
0.1U

GND35
C213 C217

M5 1 2

MAIN1V5
GND36
M9 1 2
GND30
M10
GND11
M17
0.1U
C218

GND37
N2 P15
GND12 VDD33_USB0
N4 P14
GND44 VDD33_USB2
N7
GND13
N8
GND14
VDD33_USB

N9 T15
GND15 VDD33_HDMI1
N10 U15
GND16 VDD33_HDMI
N17
GND5

USB HDMI
N21
GND54
P2 R15
VDD33

GND40 VDD33_IO
P7
GND17
P9
MAIN2V5

GND18
P10 K17

NT72563M2
GND29 VDD33_AUADC

POWER/GND
R1 J17
2
2

GND19 VDD33_AUDAC
120R
120R

R7
GND20
R11
MAIN3V3

GND45
R14 J13
GND2 VDD25_LVDS1
1
1

T2 K13
GND41 VDD25_LVDS
AUDIO LVDS
U1
L1113
L1106

GND1 1 2
U5 N16
0.1U
C185

GND46 VDD25_MPLL 1 2
V2 M16
GND

GND21 VDD25_APLL
V4 1 2
GND42
Y3
MAIN2V5

GND31 2 1
Y5 M15
GND
0.1U 0.1U 0.1U
C192 C190 C188

GND47 VDD25_TVDAC 1 2
AA3
GND26
AA4 1 2
GND27
C184

AA12
GND50
2U2

NC/2U2

AC1 J19 GND

C187

GND22 VDD25_SIFADC0
AC23 H19
VDD25_TVADC

GND23 VDD25_SIFADC1

GND
N19
VDD25_TVADC1
VDD25_SIFADC

M18
VDD25_SIFADC

VDD25_TVADC0
TVDAC DEMOD TVADC

N18
VDD25_BIAS
VDD25_TVADC

A4
VDD_CORE6
A5
VDD_CORE5 GND
B4
VDD_CORE4
B5
VDD_CORE3
C4
VDD_CORE2 1 2
C5
VDD_CORE1
D5
VDD_CORE
CORE-1V

1 2
CORE0V9

STBC & XTAL

VDD_EMMC
VDD10_STBC
VDD33_STBC

VDD33_XTAL
VDD33_ETHERNET

1 2
T16
T17

Y20
R17

AC22

1 2

1 2

GND
1 2

1 2 GND
1 2
1 2
EMMC_VDD
VDD33_NET
0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 10U

1 2
VDD09_STBC
VDD33_STBC

1 2
1 2
22U

1 2
C201 C195 C206 C205 C200 C199 C198 C207

0.1U 2U2
C208 C197
VDD09_STBC

1 2

1 2
C193
10U

1 2
0.1U 0.1U 0.1U 0.1U 10U
C180 C179 C178 C177 C176

1 2
10U
C194

MAIN1V5
VDD33_NET

VDD33_STBC

1K
R1102
CORE0V9

1 2
MAIN5V
C202
10U

1 2
GND

NC/
0.01U
C1158

1 2
1 2 1 2
GND

MAIN3V3
0.1U
0.1U

C203
C1100

100K
R1101

1 2
1
1

GND L1120
L1121

GND
EMMC_VDD

S
S
2
2

G
NC/

120R
120R

D
0.1U
C204

1 2
Q1100

1 2
GND

AO3414
0.1U
C209

C216
2U2

1 2
GND
VDD33_USB

1 2
STBC_3V3

0.1U
C212
EMMC_VDD
 PCMCIA
US1

B3 PANEL_ON
GPC_0/STSIN0_CLK/INT_1/I2C_MB_SDA
E13 A3
GPB_2/CI_HA0/CI_ALE0/ARM_UART_D_RX/I2C_MF_SDA/I2S_IN_WS/NAND_D0 GPC_1/STSIN0_VALID/INT_2/I2C_MB_SCL
F13
G13
GPB_3/CI_HA1/CI_ALE/I2S_IN_BCLK/NAND_D1 NT72563M2 CI/TS GPC_2/STSIN0_START/INT_3/I2C_MC_SDA
B2
A2
GPB_4/CI_HA2/USB2_PWEN/NAND_D2 GPC_3/STSIN0_DATA/INT_4/I2C_MC_SCL
H13
GPB_5/CI_HA3/USB3_PWEN/NAND_D3
G12
GPB_6/CI_HA4/FRC_DIMMING1/DSU_BRE/LEONDSU_BRE/OPROC_DSU_BRE/NAND_D4
G11 B20
GPB_7/CI_HA5/FRC_DIMMING2/DSU_ACT/LEONDSU_ACT/NAND_D5 GPA_0/TSI1_ERR/STSI0_ERR/I2C_MA_SDA
H10 C19
GPB_8/CI_HA6/AMBI_SPI_CLK/DSU_TX/LEONDSU_TX/OPROC_DSU_TX/NAND_D6 GPA_1/TSI1_CLK/STSI1_CLK/I2C_MA_SCL
G10 C18
GPB_9/CI_HA7/AMBI_SPI_DO/DSU_RX/LEONDSU_RX/OPROC_DSU_RX/NAND_D7 GPA_2/PTSIN1_VALID/STSIN1_VALID/I2C_MB_SDA/PTSIN2_VALID
F10 B18
GPB_10/CI_HA8/AMBI_SPI_CS/DSU_EN/LEONDSU_EN/NAND_RE# GPA_3/PTSIN1_START/STSIN1_START/I2C_MB_SCL/PTSIN2_START
E10 A18
GPB_11/CI_HA9/FR_PWM/LED_VS_OUT/NAND_CLE GPA_4/PTSIN1_D0/STSIN1_DATA/I2C_MC_SDA/PTSIN2_D0
D10 C17
GPB_12/CI_HA10/TENSILICA_TCK/USB0_PWEN/AMBI_SPI_DI/NAND_ALE GPA_5/PTSIN1_D1/I2C_MC_SCL/PTSIN2_D1
D9 A17
GPB_13/CI_HA11/TENSILICA_TMS/USB1_PWEN/AMBI_SPI_DI/NAND_WE# GPA_6/PTSIN1_D2/I2S_IN_DATA/I2C_MD_SDA/PTSIN2_D2
E9 B17
GPB_14/CI_HA12/TENSILICA_TDO/LED_PWM_0/LED_SPI_STT_HSC_SDA/NAND_WP# GPA_7/PTSIN1_D3/I2S_IN_WS/I2C_MD_SCL/PTSIN2_D3
F9 C16
GPB_15/CI_HA13/TENSILICA_TDI/LED_PWM_1/LED_SPI_DI/HSC_SCL/NAND_RB# GPA_8/PTSIN1_D4/I2S_IN_MCLK/DEMOD_QLED/PTSIN2_D4
G9 B16
GPB_16/CI_HA14/TENSILICA_TRST/LED_PWM_2/LED_SPI_CLK/LED_YDIO/NAND_CE_0# GPA_9/PTSIN1_D5/I2S_OUT_A_DATA/PTSIN2_D5
C15
GPA_10/PTSIN1_D6/I2S_OUT_A_WS/PTSIN2_D6
H9 B15
GPB_17/CI_HAD0/I2S_OUT_B_MCLK/LED_PWM_3/LED_SPI_DO GPA_11/PTSIN1_D7/I2S_OUT_A_BCLK/PTSIN2_D7
G8
GPB_18/CI_HAD1/I2S_OUT_B_BCLK/LED_PWM_4/LED_SPI_CS_0
G7
GPB_19/CI_HAD2/I2S_OUT_B_WS/LED_PWM_5/LED_SPI_CS_1/LED_SPI_STT/HSC_SDA
H7
GPB_20/CI_HAD3/I2S_OUT_B_DATA/LED_PWM_6/LED_SPI_CS_2LED_SPI_DI_HSC_SCL
G6
GPB_21/CI_HAD4/I2S_OUT_C_MCLK/LED_PWM_7/LED_SPI_CS_3
F6 A15
GPB_22/CI_HAD5/I2S_OUT_C_BCLK/3D_IR/3D_BT/3D_ACTIVE GPA_12/PTSIN2_ERR/DEMODOUT_ERR/I2S_OUT_A_MCLK/CI_CD_1#/PTSIN2_CLK
E6 E20
GPB_23/CI_HAD6/I2S_OUT_C_WS/LR0_DELAY GPA_13/PTSOUT_CLK/PTSIN2_CLK/DEMODOUT_CLK/RFAGC_VSYNC/S2_AGC
D6 D20
GPB_24/CI_HAD7/I2S_OUT_C_DATA/LR1_DELAY GPA_14/PTSOUT_VALID/PTSIN2_VALID/DEMODOUT_VALID/VIF_IF_AGC/DEMOD_IF_AGC/T2_AGC
E19
GPA_15/PTSOUT_START/PTSIN2_START/DEMODOUT_START/DEMOD_EMERGENCY
F19
GPA_16/PTSOUT_D0/PTSIN2_D0/DEMODOUT_D0
B19 F18
GPA_24/CI_RST/DISEQC_TX GPA_17/PTSOUT_D1/PTSIN2_D1/DEMODOUT_D1
H17 E18
GPA_25/CI_CD_0#/DISEQC_RX GPA_18/PTSOUT_D2/PTSIN2_D2/DEMODOUT_D2
G16 D18
GPA_26/CI_CE#/BT_SHOP_VS_IN/BT_SHOP_LR_IN GPA_19/PTSOUT_D3/PTSIN2_D3/DEMODOUT_D3
G15 D17
GPA_27/CI_IREQ#/SPDIF_IN GPA_20/PTSOUT_D4/PTSIN2_D4/DEMODOUT_D4
F14 E17
GPA_30/CI_OE#/ARM_UART_A_RX GPA_21/PTSOUT_D5/PTSIN2_D5/DEMODOUT_D5
G14 F17
GPA_31/CI_WE#/ARM_UART_C_TX GPA_22/PTSOUT_D6/PTSIN2_D6/DEMODOUT_D6
H14 G17
GPB_0/CI_REG#/ARM_UART_C_RX/I2S_IN_MCLK GPA_23/PTSOUT_D7/PTSIN2_D7/DEMODOUT_D7
D13
GPB_1/CI_HWAIT#/ARM_UART_D_TX/I2C_MF_SCL/I2S_IN_DATA
D14
GPA_28/CI_IORD#/SPDIF_OUT
E14
GPA_29/CI_IOWR#/ARM_UART_A_TX

NT72563
 ZHV ZHV1
T T
1 1
3SPB35K
PBD1

1KV
2
2
PL1

1
PCY1
220P

PR12
!

1
PD5A

1
2

PC8

PC8A
! PT1 A K

L1
1

450V PC0B
450V PC0A
2
NC

1
PC33
PR14

PC0

2
GND 1 2
!

PR13
PR15 Z27V

PR47
P

PR48
450V

2
3

1
2

2
1
1 2

220P
T

PCY2

L2
GND ! 1 VLED

2
4
3
1 9

1
N

N
4
2
PD5

1
1

2
K A N5 N4

PC30

3
PD3A

1
K
ZPGND1 ZPGND1
2 8

PD3
1

2
PC26
T T

P
1

P
PGND N1 GND

PC13
PC27

PC14
A
PGND PGND PR53

50V

50V
PU1

N
ZGND 1

2
2

N
PRX1 PRX3 PR1
2 1 2 1
T
1
PC7 3
S1 D 1 2 PR49
1

7 6 1 2
S2 PD2 7 GND
PRX2 PRX4 8 PGND PR8 GND
1
2

2 2 S3 BP 2
1 1
9 4 K A
4 N3
PR2

! PCX1 ! 10
S4 CP
3 GND GND Z12V

K
N2

1
0.47U FB T

PZD1
PC5

P
1

S5 FB 12V_IN
6 1

PC6

2
1 2 11 2 PD4

PR11
15V

2
25V
1
S6 PD

A
12 1 5

2
N

PC31
2

3
2

PGND
PR3

PGND
PRT2

PGND

1
FB PD4A

25V

25V

2
P

2
1

PC10

PC11

PC12

PR55
A K

2
T

PGND PR16
1

PGND NC

PR9
1 2

2
PD1 PCY3

1
2

1
E PR59 470P

PR6

PC29
PQ1 GND
PR17

2 1
A K 1 2 1 2 1 2
B

PR54
2

1
BT3906

PC9
2
!

PC4
!
2

PR18

PR7
1 2
PC2

2
1 2
PF1

250V

2
2

GND
PZD0 K

1
PC3
PC1

1
T
NC

1
GND
PR4

1
PR5

ZGND1
11

PGND GND
ZL

1
ZN
T

1
T

1 2
1

PR58
1

1
1
1

1
ZL1 T PGND
2
ZN1 T
PP1
GND GND
PGND
PGND
PGND
PD6
PGND
BL_ON VLED PL4 ZLED1
PR19 PGND A K VLED+
1 2 EN 1 2 T
1
VLED+

PQ2 1
PR27

PR28

PR29
D 1 ZLED
PR43

2
2

P
T
2

2
G 2

PC25
2

PC32
PU2
PC15

1 2
PR20

PR56
ZLED-

PR57
S PC22 3

100V
EN

PD7
1 16

N
1

1
ENA SOURCE 1 2 T

1
PR42

1
1

PR31
1

1
1 LED- 1
2
2 15

1
K
RI NC2

2
PR32
PR21 5

PR41
2

PC28
3 14

2
2 1 1
FAULT DRAIN
PR26

1
DRAIN

PR52
T
2

4 13 PP2

2
GND NC1 ZLED1-
PR22

GND

1
1
1

GND 5 12 ISET 1
FB ISET GND GND
PC17 PR33
1

2 1 6 COMP CS 11 1 2
ISET
OVP
A_DIM PR45 7 10

2
OVP GATE PR30
2

LED-

2
DRAIN

PR40
1 PR24 PR34
2

PR37

PR38
12V_IN

PR39
1

PR36
2
PR23

1 8 9 1
PR50

2 DIM VIN 2
2
2

PC16

1
PC24

DIM_PWM
1
PR46

1
1
1

2
OB3351FT
2

PC20

PC19
PR35
1

OVP
1

2
PR25

K
1

PC18

PC21

PZD2

2 1
1

1
24V
1

GND

2
1

2
A

GND

PR44
GND

PC23
GND GND

1
GND

1
GND
GND
6. Power Supply Block Diagram

12
5. Chassis Block Diagram

11
10. Trouble Shooting——No Picture

No Picture

Check input picture N Check Q601/Q600 Y

signal and source working condiction Check
P602/227/28/29/30
Y
P601_1/2/3/4
N Check UDF1,UDJ1,UDC1 =12V?
Check Panal_vcc
output
Y N Y
Check 0V9 & 1V5 & 3V3 Check keypoints 5V
Check panel to confirm
Y N
Check CS01 N Check reset and crystal Check UD1
and X12M oscillator circuit output
Y N
Upgrade N Check software and ID Check voltage of
soft and number keypoints 3V3STB 12V
select Y N
right ID Replace
Check PSU output
main board

35
10. Trouble Shooting——No Sound
No Sound

Check input sound signal is ok?

Check speaker and connector is ok?

Y
N
Check the audio amplifier power is 12V ? Check PSU output

Y N

Check the audio amplifier power voltage is 3v3? Replace PSU to confirm

Y
Normal the voltage N
Of LA02/LA03/ Check UA01 output pin to LA02/LA03/LA04/LA05?
LA04/LA05
Y

Replace CA22/CA23/CA24/CA25/CA26/CA27 confirm

Y
Replace UA01
36
10. Trouble Shooting——Abnormal Picture
Abnormal picture

Check input picture signal and source is ok?

Y
N
Check the LVDS or FFC connector is ok ? Upgrade software and select right
Project ID number according to BOM
Y

Check software version and project id number?

Check U12 and LVDS output circuit ,such as

resistance and PCB layout via circuit ?

Y
Y
Replace the main board to confirm? Reference “no picture” procedure
N

Replace LCD panel to confirm

37
10. Trouble Shooting——Network Fault(wired)
Can’t access the internet

Check the LAN and cable connections is ok?

Y
Access wired setting can it get IP address Y
success ? Check LAN Server
Y

Check UN2 pin1&2&3&6&7&8 voltage ?

-----------------------------------------------------
Normal condition:
The voltage at 2.5V Y

Replace the US1 to confirm Replace UN2 to confirm

N
N
Replace main board to confirm

38
10. Trouble Shooting—Network Fault(wireless)
Can’t access the internet

Check the wireless router I s ok?

Y
Y
Access wireless setting turn on wireless Make sure that it connects to a
Switch , can it fine the wireless network? Wireless network success?
N
Y
Check main board and WIFI module connect is
ok?
Check wireless server
Y

Replace the WIFI module to confirm

Upgrade software and select right

Project ID number according as BOM

N
Replace a main board that working
Properly to confirm

39