Scribd
Upload
166 views2 pages

S460M Steel Plates. Thermomechanical Rolled Weldable Fine Grain Structural Steel

This document provides information on S460M steel plates, including a product description, available dimensions, mechanical and chemical properties, and welding guidelines. S460M is a fine grain structural steel that can be thermomechanically rolled and offers good weldability, impact resistance, and formability. It meets the requirements of EN 10025-4 and is commonly used in shipbuilding, construction, and wind power. Plate thicknesses range from 8-50mm in widths up to 3200mm. The document also provides property requirements, chemical composition ranges, and contact information for the manufacturer.

Uploaded by

richad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
166 views2 pages

S460M Steel Plates. Thermomechanical Rolled Weldable Fine Grain Structural Steel

This document provides information on S460M steel plates, including a product description, available dimensions, mechanical and chemical properties, and welding guidelines. S460M is a fine grain structural steel that can be thermomechanically rolled and offers good weldability, impact resistance, and formability. It meets the requirements of EN 10025-4 and is commonly used in shipbuilding, construction, and wind power. Plate thicknesses range from 8-50mm in widths up to 3200mm. The document also provides property requirements, chemical composition ranges, and contact information for the manufacturer.

Uploaded by

richad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

S460M steel plates

Thermomechanical rolled weldable fine grain structural steel

Products description
S460М – fine grain structural steel after thermomechanical rolling. This steel grade possesses good weldability
features, high resistance to brittle cracking and good cold-forming properties. S460M steel plates meet requirements
of EN 10025-4.
It is typically used for welded structures in shipbuilding and machine-building and for construction of bridges, steel
structures and wind generators supports.

Available dimensions
S460 steel plates of quality categories М and МL are available with thicknesses of 8-50 mm. Rolled product widths can
be up to 3200 mm, lengths up to 12200 mm max. With plate thickness of 50 mm and width of 3200 mm, the maximum
length is 7500 mm. The maximum plate weight is 9.5 tons. Plates are supplied with edges trimmed.

Mechanical properties according to DSTU EN 10025-4


Thickness (t), mm Yield strength, min MPa Tensile strength, MPа Elongation, min %
≤ 16 460 540-720 17
16 ˂ t ≤ 40 440 540-720 17
40 ˂ t ≤ 50 430 530-710 17

Impact energy KV, min J


Steel grade
+20 0 -10 -20 -30 -40 -50
S460М 55 47 43 40 - - -
S460МL 63 55 51 47 40 31 27

Chemical composition
According to DSTU EN 10025-4 (mах %)
Grade С Si Мn Р S Nb V Тi Сг Ni Мо Сu Аl (min) N
S460М 0.030 0.025
0.16 0.60 1.70 0.05 0.12 0.05 0.30 0.80 0.20 0.55 0.02 0.025
S460МL 0.025 0.020

Metinvest’s products
Grade С Si Мn Р S Nb V Тi Сг Ni Мо Сu Аl (min) N
S460М
0.12 0.28 1.59 0.009 0.004 0.034 0.054 0.005 0.03 0.04 0.01 0.02 0.030 0.009
S460МL

Carbon equivalent
CEV
Thickness (t), mm
DSTU EN 10025-4 Metinvest’s products
≤ 16 0.45 0.41
16 ˂ t ≤ 40 0.46 0.43
40 ˂ t ≤ 50 0.47 0.45

metinvestholding.com 1
Welding
Due to their low carbon content and low carbon equivalent, these steels are suitable for both manual and automatic
welding as per all known welding procedures.
Due to good cracking resistance properties, pre-heating before welding is unnecessary. However, the quality of joint
weld depends on the welding procedure, its conditions and range of suitable additives. Use of gas welding is not
recommended.
It is necessary to use welding wire and welding electrodes as additives suitable for the strength category. Electrodes
with basic coating are recommended for manual welding. The grades are not suitable for heat treatment at temperatures
higher than 580°С. Stress relieving (530-580°С) is only required when prescribed.
The company that works with these steel grades should make sure that its calculations, design and methods of
treatment are suitable for this material.

Contacts
Product development

Trunin Pavel
Marketing Manager
Metinvest Holding, LLC
Tel.: +38 067 544 42 27
Email: [email protected]

Gulf countries

Metinvest International Gulf branch office


Jebel Ali Free Zone, building LOB 17,
Floor 3 PO Box 263027, Dubai, UAE
Tel.: 971 4 881 19 40
Fax: +971 4 881 19 57
Email: [email protected]

Other countries

Metinvest International
2 Rue Vallin, Geneva
1201, Switzerland
Tel.: +41 22 906 18 28
Email: [email protected]

metinvestholding.com 2

You might also like