TSS-750

6 – Piece Home Theater System

SERVICE MANUAL

Infinity Systems Incorporated

250 Crossways Park Dr.
Woodbury, New York 11797 Rev3 1/2005
 CONTENTS

BASIC SPECIFICATIONS . . . . . . . . . ………………….………….... .. . . . . . 1

DETAILED SPECIFICATIONS . . . . . . . . . . . . . . . . . .………. . .. .. .. . . . . . 2
CONTROLS & CONNECTIONS . . . . . . . . . . . ……….…………………. . . . 4
OPERATION……. . . . . .. . . . . . . . .. .. . . . .. .. . . . . ….……… . . ... . . . . . . . 6
SUB750 EXPLODED VIEW…….… . … . .. .. . . .. ……………………. ………7
TSS-750 SATELLITE DISASSEMBLY SERVICE TIP… …………...…………8
MECHANICAL PARTS LIST….…….… . … . .................................................9
SUB750 TEST SET UP AND PROCEDURE….… . … . .. .. . . .. . … . …….10
BLOCK DIAGRAM. . . . ………………... ……………….… . … . .. .. . . .. … . 11
TECH TIP INFTT2003-04 …………. .... …………………………………………12
PCB DRAWINGS. .. . . . . . . . . . . . . . .. . . . . ………………………….. . . . . …13
ELECTRICAL PARTS LIST …………. .... . .. . . . . . . . .. ..……….... .. .. . . . . 17
IC – TRANSISTOR PINOUTS . … . . .. . . . . . .……... . .. .. . ….…..….... . . . 20
SCHEMATIC DIAGRAMS . . . . . . . . .. .. .. .. . . .…... . . .. . . . ……..….…. . . .21
PACKING.. . . . . . . . . . . . . . .. . . ………… . ………………………….. . . . . …23

SPECIFICATIONS Satellites Center Channel

Frequency Range: 120Hz – 20,000Hz (±3dB) 120Hz – 20,000Hz (±3dB)

Recommended
Amplifier Power Range: 10 – 100 watts 10 – 125 watts
Sensitivity: 88dB 89dB
(2.83V @ 1 meter)
Nominal Impedance: 8 ohms 8 ohms
Crossover Frequency: 3500Hz, 24dB/Octave 3500Hz, 24dB/Octave
Midrange Driver(s): 3-1/2" MMD, magnetically shielded Dual 3-1/2" MMD, magnetically shielded
High-Frequency Driver: 3/4" MMD, magnetically shielded 3/4" MMD, magnetically shielded
Dimensions (H x W x D): 6" x 4-1/8" x 4-3/8" 4-1/8" x 9-1/4" x 4-3/8"
(152mm x 105mm x 111mm) (105mm x 235mm x 111mm)
Weight: 2.8 lb (1.3kg) 4.5 lb (2.0kg)

SUB750 Subwoofer

Frequency Range: 34Hz – 150Hz (±3dB)

Amplifier Output: 150 watts RMS, 500 watts Peak
Low-Frequency Driver: 10" (254mm) MMD™
Crossover Frequency: 50Hz – 150Hz, 24dB/Octave, continuously variable
Dimensions (H x W x D): 16-3/4" x 10-3/4" x 15-3/4" (425mm x 273mm x 400mm)
Weight: 33 lb (15.0kg)

Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and construction
details in this and related Infinity publications are therefore subject to change without notice.

1
TSS-750
SUB750 Powered Sub/ Plate Amp

LINE VOLTAGE Yes/No Hi/Lo Line Nom. Unit Notes

US 120vac/60Hz Yes 108-132 120 Vrms Normal Operation
EU 230vac/50-60Hz Yes 207-264 230 Vrms Normal operation, MOMS required

QA Test
Parameter Specification Unit Conditions Notes
Limits

Type (Class AB, D, other) D n/a n/a

Load Impedance (speaker) 4 Ohms n/a Nominal
Rated Output Power 75 Watts 75 1 input driven
Average RMS power, 3/20 Cycles 50 Hz, Driven 6dB
AVG RMS Dynamic Power 150 Watts 135 above its input sensitivity sensitivity, average level
obtained from the first 4 half cycles.
THD @ Rated Power 0.5 % 1 22k filter 75 Watts
THD @ 1 Watt 0.2 % 0.5 22k filter
DC Offset 10 mV-DC 30 @ Speaker Outputs
Measured at the amplifier board THD < 0.1% - 75
Damping factor 35 DF 22 Measured at amplifier board
Watts @ 50Hz

Input Sensitivity
Input Frequency 50 Hz 50 Nominal Freq.
L&R 162 mVrms ±2dB To 75 Watts, Ap Zo=600 Ohms Single input driven LP switch to Normal
LFE 162 mVrms ±2dB To 75 Watts, Ap Zo=600 Ohms Single input driven LP switch to LFE
Single input driven, LP switch to Normal, This applies
Speaker/Hi Level Input 1.5 Vrms ±2dB To 75 Watts
to 230VAC model only

Signal to Noise
SNR-A-Weighted 95 dBA 85 relative to rated power A-Weighting filter
SNR-unweighted 80 dBr 75 relative to rated power 22k filter
SNR rel. 1W-unweighted 65 dBr 60 relative to 1W Output 22k filter
Volume @max, w/ A/P Swept
Residual Noise Floor 1.5 mVrms(max) 2.5 Bandpass Measurement (Line Line level inputs must be terminated using 1KOHM
freq.+ harmonics) (BW=20Khz)

Input Impedance
Line Input 10K ohms n/a Nominal
Speaker/Hi Level Input >4.7K ohms n/a Nominal Applies to 230VAC model only

Filters
LP 4th order 60-150 Hz ± 10 2nd order variable, 2nd order fix
HP 2nd order Fixed 33 Hz, Q=1.8
LFE Low pass 2nd order fixed 200>LP<1K Hz
Friend circuit 65 Hz 65.6 Hz, Q=2.68
Speaker out HP filter 1st order fix
Left & Right 200 Hz ± 10 Speaker input - Spkr out 4 Ohms (Applies to 230VAC model only)
Left & Right 100 Hz ± 10 Speaker input - Spkr out 8 Ohms (Appies to 230VAC model only)

Limiter
THD at Max. Output Power YES n/a functional Maximum Output Power Limiter has no effect at maximum output power

Features --
Volume pot Taper (lin/log) LOG -- A Taper
HP Speaker input and output YES Refer to filter section (Applies to 230V model only)
Phase switch 0-180 deg
LP defeat switch (LFE-Normal) YES LFE function selection

Signal Sensing (ATO)

Auto-Turn-On (yes/no) YES functional
ATO Input test frequency 50 Hz functional
ATO Level LFE Input 3 mV functional
ATO Level Speaker in 50 mV functional
Amp connected and AC on, then
ATO Turn-on time 5 ms functional
input signal applied
T before muting, after signal is
Auto Mute/ Turn-OFF Time 15 minutes 18 Auto turn of time (T) must be 5 > T < 20 Minutes
removed

Power on Delay time 3 sec. 4 AC Power Applied

Transients/Pops
ATO Transient 5 mV-peak n/a @ Speaker Outputs
Turn-on Transient 50 mV-peak 2V-pk-pk @ Speaker Outputs AC Line cycled from OFF to ON
Turn-off Transient 50 mV-peak 2V-pk-pk @ Speaker Outputs AC Line cycled from ON to OFF

Efficiency
Efficiency 65 % 65 Nominal Line voltage 120 VAC / 230 VAC
Stand-by Input Power 12 Watts 15 @ nom. line voltage Auto turn of time (T) must be 5 > T < 20 Minutes
Power Cons. @ rated power 115 Watts 120 @ nom. line voltage 75 Watts @ 4 Ohms nominal line voltage

2
TSS-750

QA Test
Parameter Specification Unit Conditions Notes
Limits
Protections
Amplifier should resume operation after short circuit
Short Circuit Protection YES functional Direct short at output
condition removal
Temperature rise in accessible metal parts should not
Thermal Protection YES functional @1/8 max unclipped Power exceed 35K rise for domestic version or 30K rise for
European versions
No Offset at the speaker output under any operating
DC Offset Protection YES - DC present at Speaker Out leads
condition including abnormal operation
Line Fuse Rating
US Domestic version 1.25 Amps 1.25 Type-T or Slo Blo-250 V Internal fuse with UL/CSA/SEMKO rated holder
Type-T or Slo Blo-250 V, Low
EU 0.8 Amps 0.8 Internal fuse with UL/CSA/SEMKO rated holder
Breaking capacity
ALL SPECS SHOULD BE MEASURED AT NOMINAL LINE VOLTAGE.

3
TSS-750

SUBWOOFER CONTROLS
Rear Panel
Subwoofer-Level Control

 LFE/Normal Switch

 Phase Switch

 Crossover-Frequency Adjustment
¡
LEVEL  Line-Level (LFE) Inputs
Min Max
 Power Switch
LFE NORMAL
™
£ PHASE 0˚ 180˚

CROSSOVER
FREQUENCY
¢ 50Hz 150Hz

L ∞ R A Few Suggestions
We recommend that you do not operate your speakers or
LINE LEVEL IN
subwoofer with the bass, treble and loudness controls set to
For LFE use L or R full boost.This will place undue strain on your electronics and
speakers and could damage them.

The volume control setting on your processor/preamp or receiver

is not a specific indication of the overall loudness level of the
speakers.The only important consideration is the loudness level at
ON OFF AC 120V
which the system can be played, regardless of where the volume
§ POWER 60 Hz 180W control is set.

Always turn down the volume control setting on your processor/

preamp or receiver when changing a cassette or CD, or switching
inputs to AM or FM operation. Excessively loud transients (clicks or
® popping sounds) can damage the satellite speakers and possibly
the subwoofer.
SUB750
Important!
CAUTION
RISK OF ELECTRIC SHOCK ®
Whenever changing cables, pulling plugs, etc., ALWAYS TURN OFF
DO NOT OPEN
ALL EQUIPMENT, including the subwoofer.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, NRTL/C
CSA22.2
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. UL1492
AVERTISSEMENT: POUR PRÉVENIR LES RISQUES D’INCENDIE OU
DE CHOC ÉLECTRIQUE, ÉVITER D’EXPOSER CET APPAREIL A LA
PLUIE OU A L’HUMIDITÉ.

4
TSS-750

SUBWOOFER CONNECTIONS
If your receiver/processor does not contain
If you have a Dolby* Digital or DTS receiver/ ®
a Dolby Digital or DTS processor but has a
processor with a low-frequency-effects (LFE) subwoofer output:
or subwoofer output:

SUBWOOFER OR RECEIVER/PROCESSOR
LFE OUTPUT LEVEL
Min Max

LFE NORMAL

PHASE 0º 180º
LEVEL 80Hz

15' Min Max

CROSSOVER
subwoofer LFE NORMAL FREQUENCY
50Hz 150Hz
cable PHASE 0º 180º

included 80Hz
15' subwoofer L R
CROSSOVER
FREQUENCY
cable included LINE LEVEL IN

50Hz 150Hz For LFE use L or R

L R Set line-level/LFE switch to “Normal.”

LINE LEVEL IN

For LFE use L or R

NOTE: If your receiver/processor has only one sub out,

you may use either the L or R input.
Set line-level/LFE switch to “LFE.”

TSS-750
5
TSS-750

OPERATION
Surround Modes Crossover Adjustment
When using the TSS-750 in a Dolby Pro Logic* home theater The Crossover Frequency Control  determines the highest
system, make sure the receiver’s center channel mode is set to frequency at which the subwoofer reproduces sounds. For the
“Normal.” When using the system in a Dolby Digital or DTS home TSS-750, it is recommended that this control be set at 120Hz
theater system, make sure all speakers are set to “Small”. (approximately the 3 o’clock position).
Some Dolby Digital-equipped receivers/processors offer different NOTE: This control will have no effect if the LFE/Normal Switch
setup options for each source or surround mode, e.g., CD-stereo,  is set to LFE. If you have a Dolby Digital or DTS receiver/
videotape, Dolby, Pro Logic. In each case, follow your equipment’s processor, the Low-Pass Frequency is set by the receiver/
instructions to ensure that the subwoofer output is turned on and processor. Set the LFE/Normal Switch  on the subwoofer to
that the speakers are set to “Small” in each mode. LFE. Consult your owner’s manual to learn how to view or change
this setting. A setting of 120Hz – 150Hz is recommended.
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the Phase Control
outlets on the back of the receiver. The Phase Switch  determines whether the subwoofer
Initially set the Subwoofer Level Control
to the“MIN” position. speaker’s piston-like action moves in and out with the main
speakers, 0˚, or opposite the main speakers, 180˚. Proper phase
Turn on the subwoofer by pressing the Power Switch  on the
adjustment depends on several variables such as room size,
rear panel.
subwoofer placement and listener position. Adjust the phase
Turn on your entire audio system and start a CD or movie sound- switch to maximize bass output at the listening position.
track at a moderate level.
Final Positioning
Auto On/Stand-By After correctly connecting the TSS-750 system and verifying that
With the Power Switch  in the ON position, the LED on the front both the subwoofer and all satellite speakers are playing, it is
panel will remain lit in red or green to indicate the On/Stand-By time to optimize the system for your particular listening room.
mode of the subwoofer. Earlier, you placed the subwoofer in its general location. Finding
RED = STAND-BY (No signal detected, Amp Off) the exact location for optimum performance sometimes only
GREEN = ON (Signal detected, Amp On) involves moving the speakers up to a few inches in any
direction. We urge you, therefore, to experiment with placement,
The subwoofer will automatically enter the Stand-By mode after if possible, until your speakers deliver their full potential.
approximately 10 minutes when no signal is detected from your
system.The subwoofer will then power ON instantly when a signal
is detected. During periods of normal use, the Power Switch 
can be left on.You may turn off the Power Switch  for extended
periods of nonoperation, e.g., when you are away on vacation.

Adjust Level
Turn the Subwoofer Level Control
up about half way. If no
sound emanates from the subwoofer, check the AC-line cord and
input cables.Are the connectors on the cables making proper
contact? Is the AC plug connected to a “live” receptacle? Has the
Power Switch  been pressed to the “On” position? Once you
have confirmed that the subwoofer is active, proceed by playing a
CD or DVD. Use a selection that has ample bass information.

Set the overall volume control of the receiver/processor to a

comfortable level. Adjust the Subwoofer Level Control
until
you obtain a pleasing blend of bass. Bass response should
not overpower the room but rather be adjusted so there is
a harmonious blend across the entire musical range. Many
users have a tendency to set the subwoofer volume too loud,
adhering to the belief that a subwoofer is there to produce lots of
bass.This is not entirely true. A subwoofer is there to enhance
bass, extending the response of the entire system so the bass
can be felt as well as heard. However, overall balance must
be maintained or the music will not sound natural. An experienced
listener will set the volume of the subwoofer so its impact on
bass response is always there but never obtrusive.

6
TSS-750

SUB-750 EXPLODED VIEW

SERVICE NOTE
Access to woofer:
1) Carefully pry metal grille out of its
recess with a sharp pointed
instrument such as an awl – USE
CAUTION. Work evenly around
the perimeter until the grill w/
gasket can be removed.
2) Remove the (4) Phillips screws
holding the trim ring to the cabinet.
3) Remove the (4) Phillips screws
holding the woofer to the cabinet.

REPLACEMENT: Assure when the woofer

is replaced, it is exactly centered in the
counterbore. If it is offset, replacement of
the trim ring and grille will be difficult.

SUB-750 Mechanical Parts List

Part number Description QTY

Not for Sale TSS-750 SUB Wood cabinet, Platinum 1

Not for Sale TSS-750 SUB Wood cabinet, Charcoal 1
750-GR-PLT TSS-750 SUB Grill with gasket, Platinum 1
750-GR-CHR TSS-750 SUB Grill with gasket , Charcoal 1
750-TR-PLT TSS-750 SUB Trim ring, Platinum 1
750-TR-CHR TSS-750 SUB Trim ring, Charcoal 1
Not for Sale TSS-750 SUB Plastic Front baffle 1
Not for Sale TSS-750 SUB Aluminum panel, platinum 1
Not for Sale TSS-750 SUB Aluminum panel, charcoal 1
750-LED TSS-750 SUB LED 1
750-PRT-PLT TSS-750 SUB Port tube, platinum 1
750-PRT-CHR TSS-750 SUB Port tube, charcoal 1
Not for Sale TSS-750 SUB Amp(1), 120V 1
Not for Sale TSS-750 SUB Amp(2), 230V 1
750-10D 10" woofer DCR = 4.6 ohms ±10% 1
750-FT-CHR TSS-750 SUB rubber feet, charcoal 4
750-SCREW1 TSS-750 AMP screws 10
750-SCREW2 TSS-750 SUB woofer screws 4

7
TSS-750

Service Tips
May 2004
To: Infinity Service Centers

Models: TSS-750 Satellites

Subject: How to Disassemble the Satellite Loudspeakers

To disassemble the satellites, a small hook or dental pick is necessary (see Picture 1)
The hook can be used to take the front grille off, and then to remove the front baffle.

To remove the front baffle, place the hook in the small hole in the corner next to the woofer as on Picture 2 and pull out so
the small hook pulls the tabs on front baffle loose from the cabinet. See Picture 4 to locate the tabs. It is easiest to start with
the corners next to the woofer, as there may be glue around the tweeter that makes it more difficult to start on that end.

Picture 3 shows the satelite when it is disassembled

Picture 1 Picture 2

Picture 3 Picture 4

Model Serial number Status Action

TSS-750 SAT All Repair

8
TSS-750

TSS-750 SATELLITES, CENTER, PACKING

Part number Description

750-TW Tweeter for TSS-750 sat/center

750-GSPLT Grill cover w / logo for satellite TSS-750 platinum
750-FRSPLT Front panel for satellite TSS-750 platinum
750-CVSPLT Satellite TSS-750 platinum top & bottom cap
750-XS X-over network for satellite TSS-750
750-350DS 3-1/2” driver 4 ohm for satellite TSS-750
750-TMSPLT Terminal for satellite TSS-750 platinum
750-TMCPLT Terminal for center TSS-750 platinum
750-XC X-over network for center TSS-750
750-350DC 3-1/2” driver 8 ohm for center TSS-750
750-GCPLT Grill cover w / logo for center TSS-750 platinum
750-CRPLT Cradle for center TSS-750 platinum
750-FRCPLT Front panel for center TSS-750 platinum
750-CCVPLT Center TSS-750 platinum left & right cap

PACKING

750-FOAM TSS-750 System Styrofoam

750CTN-PL120 Carton for TSS-750 platinum 120V
750CTN-PL230 Carton for TSS-750 platinum 230V
750OM-120 120V Owner manual for TSS-750
750OM-230 230V Owner manual for TSS-750
750WS-120 TSS-750 warranty sheet 120V
750-BRTPLT TSS-750 Wall mount bracket platinum
120v Speaker wire with RCA cable for TSS-750 120V
230v Speaker wire with RCA cable for TSS-750 230V

750CTN-STD-PL Carton for TS-Stand platinum

750STD-OM TS-Stand Owner manual
750STD-WS TS-Stand warranty sheet

TSS-750CHR , TSS-750CHR/230 & TS-STANDCHR spare parts

Part number Description

750-TMSCHR Terminal for satellite TSS-750 charcoal
750-TMCCHR Terminal for center TSS-750 charcoal
750-GSCHR Grill cover w / logo for satellite TSS-750 charcoal
750-GCCHR Grill cover w / logo for center TSS-750 charcoal
750-CRCHR Cradle for center TSS-750 charcoal
750-FRSCHR Front panel for satellite TSS-750 charcoal
750-FRCCHR Front panel for center TSS-750 charcoal
750-CVSCHR Satellite TSS-750 charcoal top & bottom cap
750-CCVCHR Center TSS-750 charcoal left & right cap
750CTN-CH120 Carton for TSS-750 charcoal 120V
750CTN-CH230 Carton for TSS-750 charcoal 230V
750CTN-STD-CH Carton for TS-Stand charcoal

9
TSS-750

SUB750 Test Set Up and Procedure

SYSTEM AURAL SWEEP TEST

Equipment needed:
• Function/signal generator/sweep generator
• Multimeter
• RCA cables

General Unit Function (UUT = Unit Under Test)

Switches/knobs on the amplifier faceplate:
Crossover Frequency Adjust full CW (150Hz)
Phase switch – either position
Normal/LFE switch - Normal
1. From the signal generator, Connect both right and left line level inputs (RCA jacks) – to signal generator and
UUT. Use Y-cable if necessary from mono source.
2. On the amplifier, turn the LEVEL control full Counterclockwise (Min).
3. Turn on generator, adjust to 90mV, 50 Hz.
4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max).
5. LED should now be Green; immediate bass response should be heard and felt from rear port tube opening.

Sweep Function
1. Follow steps 1-5 above, using a sweep generator as a signal source.
2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofer and test.

Driver Function (Woofer)

1. Remove woofer from cabinet (follow steps on exploded view page); detach + and - wire clips.
2. Check DC resistance of woofer; it should be 4.6 ohms±10%.
3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated
amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.

10
 TSS-750

BLOCK DIAGRAM

TSS-750

FUSES

11
TSS-750

TECH TIPS
Troubleshooting tips and solutions to common service problems

For models: PS-10, PS-12, SUB750, SW-10 TIP# INFTT2003-02 Rev2

Subject: Replacing Output MOSFETS

In the event you need to replace MOSFET transistors Q18 or Q22 as part of a repair:
It is important to use ONLY the Infinity part# FE106401110, 051-640001-000, or only the brands:
International Rectifier, or Fairchild.
Replace both Q18 and Q22 MOSFET’s in the circuit, even if only one seems to be damaged.
Do NOT mix & match these components from different manufacturers, or batches. They should be
identical.

12
TSS-750

13
TSS-750

14
TSS-750

15
TSS-750

16
TSS-750
SUB750 120V ELECTRICAL PARTS LIST
Part Number Description Qty Reference Designator

Resistors

020-000098-400 Carbon Film 0R 1/8W 1 C22-C24,C31

020-220497-120 Carbon Film 2K2 1/4W J 1 R11
021-000097-100 Metal Film Resistor 0R 1/4W F 1 R10
021-100401-120 MOF Resistor 1K 1W J 1 R103
021-820305-020 MOF Resistor 820R 5WS J 8x20 1 R6,9
022-500003-020 Resistor KNP 0R05 3WS J FK TYPE 1 R104
024-100298-120 SMD Resistor 10R 1/8W J 0805 1 R81,82
024-100398-120 SMD Resistor 100R 1/8W J 0805 1 R62
024-100498-120 SMD Resistor 1K 1/8W J 0805 1 R79,83,92,95,96,105,108,65
024-100598-120 SMD Resistor 10K 1/8W J 0805 1 R2,17,19,37,54,58,63,71
024-100698-120 SMD Resistor 100K 1/8W J 0805 1 R3,112
024-110598-100 SMD Resistor 11K 1/8W F 0805 1 R98
024-120498-120 SMD Resistor 1K2 1/8W J 0805 1 R51,53
024-130498-100 SMD Resistor 1K3 1/8W F 0805 1 R110
024-133698-100 SMD Resistor 133K 1/8W F 0805 1 R45
024-137698-100 SMD Resistor 137K 1/8W F 0805 1 R32
024-147498-100 SMD Resistor 1K47 1/8W F 0805 1 R5A
024-150598-100 SMD Resistor 15K 1/8W F 0805 1 R29
024-150698-120 SMD Resistor 150K 1/8W J 0805 1 R4A
024-160598-100 SMD Resistor 16K 1/8W F 0805 1 R135
024-200598-120 SMD Resistor 20K 1/8W J 0805 1 R94
024-220398-120 SMD Resistor 220R 1/8W J 0805 1 R90
024-220498-121 SMD Resistor 2K2 1/8W J 0805 1 R1,87,61,68
024-220598-120 SMD Resistor 22K 1/8W J 0805 1 R118,50,52
024-220798-120 SMD Resistor 2M2 1/8W J 0805 1 R80,121
024-237598-120 SMD Resistor 23K7 1/8W F 0805 1 R48
024-240398-120 SMD Resistor 240R 1/8W J 0805 1 R2A
024-270498-120 SMD Resistor 2K7 1/8W J 0805 1 R73,64
024-287498-100 SMD Resistor 2K87 1/8W F 0805 1 R38
024-300398-120 SMD Resistor 300R 1/8W J 0805 1 R55
024-300598-120 SMD Resistor 30K 1/8W J 0805 1 R56
024-330498-120 SMD Resistor 3K3 1/8W J 0805 1 R7,8,12-15,59,67
024-330598-120 SMD Resistor 33K 1/8W J 0805 1 R4,5
024-332498-100 SMD Resistor 3K32 1/8W F 0805 1 R26,27
024-360498-100 SMD Resistor 3K6 1/8W F 0805 1 R28
024-360598-120 SMD Resistor 36K 1/8W J 0805 1 R39
024-390498-120 SMD Resistor 3K9 1/8W J 0805 1 R93
024-390598-120 SMD Resistor 39K 1/8W J 0805 1 R77
024-430498-120 SMD Resistor 4K3 1/8W J 0805 1 R78
024-453598-100 SMD Resistor 45K3 1/8W F 0805 1 R30
024-470298-120 SMD Resistor 47R 1/8W J 0805 1 R101,102
024-470398-120 SMD Resistor 470R 1/8W J 0805 1 R76,99,100
024-470498-120 SMD Resistor 4K7 1/8W J 0805 1 R85,86
024-470598-120 SMD Resistor 47K 1/8W J 0805 1 R44,47,49,107
024-470698-120 SMD Resistor 470K 1/8W J 0805 1 R70
024-470798-120 SMD Resistor 4M7 1/8W J 0805 1 R60
024-536498-100 SMD Resistor 5K36 1/8W F 0805 1 R36
024-560598-120 SMD Resistor 56K 1/8W J 0805 1 R122
024-620398-100 SMD Resistor 620R 1/8W F 0805 1 R16,18
024-620398-120 SMD Resistor 620R 1/8W J 0805 1 R57
024-649298-100 SMD Resistor 64R9 1/8W F 0805 1 R6A
024-680498-120 SMD Resistor 6K8 1/8W J 0805 1 R46,91,40-43
024-680598-120 SMD Resistor 68K 1/8W J 0805 1 R33,34A,31,66
024-750798-120 SMD Resistor 7M5 1/8W J 0805 1 R134
024-820598-120 SMD Resistor 82K 1/8W J 0805 1 R69

17
TSS-750
Part Number Description Qty Reference Designator

024-825498-100 SMD Resistor 8K25 1/8W F 0805 1 R35A

025-010300-000 Thermister TSE-103 K L:50mm 1 TH1
026-200595-269 VR 20KX2 FREQUENCY PN:RD163121R03D-20KBx2(EJ) 1 VR2
026-500495-252 VR 5KA VOLUME PN:RK163111R52B-5KA (EJ) 1 VR1

Capacitors

031-100244-100 SMD Ceramic Capacitor 0u01/50V K 0805 X7R 1 C33,45,51,66,67,5,10

031-100343-100 SMD Capacitor 100pF/50V J 0805 NPO 1 C36,58
031-100344-100 SMD Capacitor 0u1/50V K 0805 X7R 1 C11,42-44,46-49,52,54,55,60
031-100384-100R SMD Capacitor 0u1/250V K 1206 X7R 1 C3,7
031-220243-103 SMD Capacitor 0u022/50V J 0805 X7R 1 C40
031-220344-100 SMD Capacitor 220pF/50V J 0805 NPO 1 C20,21,19
031-330444-300 SMD Capacitor 3300pF/50V K 0805 X7R 1 C34
031-470244-102 SMD Capacitor 0u047/50V K 0805 X7R 1 C62,59
031-560243-100 SMD Capacitor 56pF/50V J 0805 NPO 1 C57,61
031-560343-102 SMD Capacitor 560pF/50V J 0805 NPO 1 C56
032-100484-200 END Mylar Capacitor 1uF/250V K P:15 1 C70,C70B
032-270343-301 Mylar Capacitor 0u27/63V J P:5 1 C29
032-820244-200 Mylar Capacitor 0u082/100V K (R) 1 C30
033-470464-270 NPE Capaciator 4u7/100V K10 (R)1015 GNE 1 C73
033-680464-270 NPE Capaciator 6u8/100V K10 (R)1020 GNE 1 C72
034-100525-300 Electrolytic Capacitor 10uF/25V M (R)0511 P:5 1 C35
034-100625-300 Electrolytic Capacitor 100uF/25V M (R)6.3x11 P:5 1 C64
034-220525-301 Electrolytic Capacitor 22uF/25V M (R)5x11 P:5 1 C4,9,41,50,53
034-220615-301 Electrolytic Capacitor 220uF/16V M (R)0611 P:5 1 C37
034-330515-000 Electrolytic Capacitor 33uF/16V M (R)0511 P:5 1 C39
034-330525-300 Electrolytic Capacitor 33uF/25V M (R)0511 P:5 1 C1
034-330615-300 Electrolytic Capacitor 330uF/16V M (R)0812 P:5 1 C12,78
034-470415-301 Electrolytic Capacitor 4u7/50V M (R)0511 P:5 1 C2
034-470615-301 Electrolytic Capacitor 470uF/16V M (R)0812 P:5 1 C65
034-470794-200 Electrolytic Capacitor 4700uF/80V M (R)25x50 1 C6,8
035-100363-300 PE Capacitor 0u1/100V J P:5m/m 1 C28,2A
035-220353-300S PE Capacitor 0u22/63V J P:5mm 1 C27
035-470243-300 PE Capacitor 0uF047/50V J P:5mm 1 C1A
035-470353-301 ESK Capacitor 0u47/63V J P:5m/m 1 C25,26
038-100363-300 MPE Capacitor 0u1/100V J 1 C68,69
039-100390-100 UL Safety Capacitor 0u1/275V PN:XG275M104VSL7 1 CXAC1

Semiconductors

051-000600-100 Transistor NPN PN:MPSW06RLRA TO-92 (ON) 2 Q2,Q16

051-003100-000 Transistor NPN PN:TIP 31C TO-220 (MOSPEC) 1 Q4
051-005600-100 Transistor PNP PN:MPSW56RLRA TO-92 (ON) 1 Q3
051-222200-100 Transistor NPN PN:MPS2222ARLRA TO-92 1 Q21
051-290700-100 Transistor PNP PN:MPS2907A RLRA TO-92 2 Q19,23
051-540101-000 Transistor PNP PN:2N5401 TO-92 1 Q1
051-555100-000 Transistor NPN PN:2N5551 TO-92 1 Q17
051-640001-000 Mosfet N-Channel PN:IRF640N TO-220 (IR) 2 Q18,22
052-400080-000 Diode Bridge PN:RS804 400V,8A 1 BR1
053-211100-000 IC;DIP,Half-Bridge Driver PN:IR2111 8PIN (IR) 1 U7
054-000100-100 SMD Diode PN:ES1D 200V 1A 5 D5,26,29,33,38
054-001002-100 SMD Zener Diode PN:BZX84C10 10V SOT-23 1 D35
054-001501-100 SMD Zener Diode PN:BZX84C15 15V SOT-23 3 D6,7,9
054-007200-100 SMD IC Dual Op-amp PN:TL072CDR SO-8 (TI) 2 U5,6
054-007400-100 SMD IC;(OP)Quad Op-amp PN:TL074CDR (TI) 2 U2,3
054-011400-100 SMD Transistor PN:DTC114TKA SMT3 (ROHM 1 Q7
054-033904-100 SMD Transistor PN:MMBT3904LT1 SOT23 (ON 7 Q11,14,13,5,8,25,9
054-033906-100 SMD Transistor PN:MMBT3906LT1 SOT23 (ON 4 Q6,10,12,15
054-045580-100 SMD IC;(OP)Dual Op-amp PN:NJM4558M-TE3 DMP-8 1 U4

18
TSS-750
Part Number Description Qty Reference Designator

054-050601-100 SMD Zener Diode PN:BZX84C5V6 5.6V SOT-23 3 D24,36,37

054-414803-100 SMD Diode PN:LL4148 (Wishay) 1 D1-4,8,10-23,27,28,30-32,
054-540100-100 SMD Transistor PN:MMBT5401 LT1 SOT-23 3 Q20,24,26

Miscellaneous

041-115001-000 Bead Coil YT-10911 1 L5

042-010052-003 Transformer YT-10615-4 1
043-300101-000 Inductor PN:YT-10033 30uH 1 L2
043-324300-000 Inductor 324uH YT-10778 1 L4
043-560200-000 Inductor 56uH YT-10779 1 L1
043-700101-000 Toroidal Inductor 70uH YT-10682 1 L3
044-100100-000 SMD Ferrite Bead PN:321611 600R/100MHz 1206 1 FB1,FB2
008-000201-450 Fuse Label 21x5mm 1
008-001008-133 Label 97x74.8 t=0.254mm 1
008-002007-023 Label 200.3x71.1 t=0.254mm 1
008-061215-000 Gasket C4305 12x15 t=5mm 1
008-062002-002 Gasket PN:L-32 200x20mm t=5mm 1
008-062002-012 Gasket 200x20mm t=2mm 1
008-063208-000 Gasket C4305 321x8 t=1mm 1
008-069304-000 Gasket C4305 93x4 t=1mm 1
015-201205-100 Double-sided PCB ; FR-4 199x124x1.6mm 1
061-020000-000 Knob φ20x15m/m UL94V-0 BLK 1
061-314002-000 Srtain Relief P/N SB4F-2 1
061-400014-000 Rubber Foot ID:6.2 OD:11.5 t=2mm BLK 1
061-700044-000 Myca 13x18mm TO-220 1
063-010012-000 Bracket for Transistor P/N:TRK-1 1
063-321102-000 Panel 322x105.7x15mm ABS-94VO BLK 1
063-531808-000 Bucket 322x105.7x146.5mm BLK (94VO) 1
066-120300-900 Cable Tie CV-120S 1
071-100608-100 Fiber Washer OD=8mm ID=3.2 t=1 (red) 1
071-100851-000 Washer ID=5.1 OD=12 t=1m/m 1
072-010007-000 RCA Jack SCJ-1020 2P(G) wht/red 1
072-040039-000 Terminal PC205 (t=0.8m/m) T205MA 1 S-
072-040064-000 Terminal PC250(t=0.8),T250MA 1 S+
072-040096-000 Terminal (t=0.8mm) PC187(0.8) 1 AC1,AC3,T1,T2,AC2,SW2,SW4
072-040169-000 Connector 2 PIN JS-1001-2 P:2.5mm 1
073-011001-400 Bracket 16x34mm t=0.8mm 1
073-032088-600 Black Anodized 58x32x70mm 1
073-050001-000 Fuse Clip P/N:CFFH1206 1
074-020018-000 Rocker SW PN:RF1003-BB4-0 1
074-030002-000 Toggle SW PN:L101-T2B4QE 1 SW5,SW6
074-300018-000 Relay PN:943-1C-48D 1 K1
080-060351-009 Tinned Plated copper Wire φ0.6x63m/m 1 VR2-GNE
082-022241-001 Wire set #22 UL1007 L=410mm blk/wht 1
083-041802-009 ULPower Cable SPT-2 BLK #18 1
093-105202-300 FUSE:UL GSL(2AG) FUSE:2A,250V,5*20mm 1 F1
181-911600-161 Wire set #16AWG UL1007 L=610mm T205 blk 1 Out-
181-911655-135 Wire set #16AWG UL1007 L=610mm T250 green 1 Out+
181-921600-000 Wire set #16 UL1015 (blk) L:140mm T187 1
181-921699-000 Wire set #16 UL1015 (wht) L:160mm T187 1

19
20
TSS-750

21
 TSS-750

22
TSS-750

TSS-750
Packaging

OWNER’S MANUAL
120V – 750OM-120
230V – 750OM-230
TSS-750 SYSTEM STYROFOAM
750-FOAM
WARRANTY SHEET
120V – 750WS-120

SPEAKER WIRE TSS-750

WITH RCA CABLE WALL MOUNT BRACKET
FOR TSS-750 PLATINUM
(120V system) – #120V 750-BRTPLT
(230V system) – #230V

TSS-750 SYSTEM STYROFOAM

750-FOAM

CARTON FOR
TSS-750 PLATINUM
120V – 750CTN-PL120
230V – 750CTN-PL230

23