-|Transparent Guide|-

TCD210059AA Ordering Information

This is only for reference, the actual product does not support all combinations.
For selecting the specified model, follow the Autonics website.

BRQ P S ❶ - ❷ D T A - ❸ - ❹
❶ Sensing distance ❸ Connection

Cylindrical
Number: Sensing distance (unit: mm) No mark: Cable type
Number+M: Sensing distance (unit: m) C: Connector type
❷ Sensing type ❹ Control output

Photoelectric Sensors
T: Through-beam No mark: NPN open collector output
P: Polarized retroreflective P: PNP open collector output
D: Diffuse reflective

Product Components
Sensing type Through-beam Polarized retroreflective Diffuse reflective
Product components Product, instruction manual
Reflector - MS-2S -
Adjustment screwdriver ×1 ×1 ×1
M18 fixing nut ×4 ×2 ×2

Specifications
Model BRQPS□-TDTA-□ -□ BRQPS3M-PDTA-□-□ BRQPS□-DDTA-□-□
Sensing type Through-beam Polarized retroreflective Diffuse reflective
100 mm 400 mm 700 mm
Sensing distance 10 m 20 m 3 m 01) 02) 02) 03)

Sensing target Opaque materials Opaque materials Opaque, translucent materials

Min. sensing target ≥ Ø 7 mm ≥ Ø 75 mm -
Hysteresis - - ≤ 20 % of sensing distance
Response time ≤ 1 ms
Light source Red Red Red
Peak emission
660 nm 660 nm 660 nm
wavelength
Sensitivity adjustment YES (Adjuster) YES (Adjuster) YES (Adjuster)
Mutual interference
- YES YES
prevention
Operation mode Light ON mode - Dark ON mode selectable (Control wire)

BRQ Series (side sensing type)

Indicator Operation indicator (yellow), stability indicator (green), power indicator (red) 04)
Approval ᜢᜧᜫ ᜢᜧᜫ ᜢᜧᜫ

01) Reflector (MS-2S)

CATALOG
02) Non-glossy white paper 100 × 100 mm 
03) Non-glossy white paper 200 × 200 mm
04) Only for the emitter

Polarized retroreflective,
Unit weight (packaged) Through-beam
Diffuse reflective

For your safety, read and follow the considerations written in the instruction Cable type ≈ 120 g (≈ 170 g) ≈ 70 g (≈ 130 g)

manual, other manuals and Autonics website. Connector type ≈ 35 g (≈ 120 g) ≈ 25 g (≈ 120 g)

The specifications, dimensions, etc. are subject to change without notice for product
Power supply 10-30 VDCᜡ ±10 % (ripple P-P: ≤ 10 %)
improvement. Some models may be discontinued without notice.
Current consumption It depends on the sensing type
Through-beam Emitter: ≤ 20 mA, receiver: ≤ 20 mA
Reflective ≤ 30 mA
Control output NPN open collector output / PNP open collector output model
Features Load voltage ≤ 30 VDCᜡ
Load current ≤ 100 mA
• Excellent noise immunity and minimal influence from ambient light Residual voltage NPN: ≤ 2 VDCᜡ, PNP: ≤ 2 VDCᜡ

• Reverse power protection circuit, reverse output protection circuit, Protection circuit Reverse power/output protection circuit, output short overcurrent protection circuit

output short overcurrent protection circuit Insulation resistance ≥ 20 MΩ (500 VDCᜡ megger)
Noise immunity ±240 VDCᜡ the square wave noise (pulse width: 1 ㎲) by the noise simulator
• Mutual interference prevention function (except through-beam type) Dielectric strength 1,000 VACᜠ 50/60 Hz for 1 min
• Sensitivity adjuster Vibration
1.5 mm double amplitude at frequency of 10 to 55 Hz (for 1 min) in each X, Y, Z
direction for 2 hours
• Light ON/Dark ON mode selectable by control wire Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times
• Protection rating : IP67 (IEC standard) Ambient illuminance
Sunlight: ≤ 11,000 lx, incandescent lamp: ≤ 3,000 lx
(receiver)
Ambient temperature -25 to 60 ℃, storage: -30 to 70 ℃ (no freezing or condensation)
Ambient humidity 35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)
Protection rating IP67 (IEC standard)
Connection Cable type / Connector type model
Cable spec. Ø 4 mm, 4-wire, (Emitter: 2-wire), 2 m
Wire spec. AWG26 (0.52 mm, 20-core), insulator outer diameter: Ø 1 mm
Connector M12 4-pin plug type
Material Case: PC, lens and lens cover: PMMA

ᜢᜧᜫ
-|Transparent Guide|-

Dimensions
• Unit: mm, For the detailed drawings, follow the Autonics website.
A Optical axis of emitter D Stability indicator (green)
B Optical axis of receiver E Power indicator (red)
C Operation indicator (yellow) F Sensitivity adjuster

6.8 A
A B B
24

14
5.3
5.3
5.3

50
M18×1

31

70.5
74.5
E E C D C D F
Ø4, 2m
16.8
Emitter Receiver Polarized retroreflective,
Diffuse reflective Cable type

6.8
A B B A
24

14
5.3
5.3
5.3

50
M18×1 31

70.5
80.5

E E C D C D
F
16.8 M12×1
Emitter Receiver Polarized retroreflective,
Diffuse reflective Connector type

■ Reflector (MS-2S) ■ M18 fixing nut

2-Ø3.8
4.2

4 24 M18×1
60.5
52

24

34 3.25 2.5
40.5 8.5

Sold Separately
• Reflector: MS Series • Bracket: BK-BR-A
• Retroreflective tape: MST Series • Connector cable, connector connection cable

Sold Separately: Bracket (BK-BR-A)

• Unit: mm, For the detailed drawings, follow the Autonics website.
Ø3.4
15.2
9.2

7
19 Ø18.5
1.2
2-Ø3.4
24.1
42
27
15

2-30° 4-Ø1.7
24
36

18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002

www.autonics.com | +82-2-2048-1577 | [email protected]