950H/962H Wheel Loaders Specifications

Engine – 950H
Engine – 962H

Engine Model Cat C7 ACERT Engine Model Cat C7 ACERT

ISO 9249/SAE J1349 (metric) 147 kW 200 hp ISO 9249/SAE J1349 (metric) 156 kW 212 hp
ISO 9249/SAE J1349 (imperial) 197 hp ISO 9249/SAE J1349 (imperial) 209 hp
ISO 14396/SAE J1995 (metric) 162 kW 220 hp ISO 14396/SAE J1995 (metric) 172 kW 234 hp
ISO 14396/SAE J1995 (imperial) 217 hp ISO 14396/SAE J1995 (imperial) 231 hp
Net Power – 80/1269/EEC 147 kW 197 hp Net Power – 80/1269/EEC 158 kW 211 hp
Peak Torque (Net) @ 1,400 rpm 907 N·m 669 ft-lb Peak Torque (Net) @ 1,400 rpm 907 N·m 669 ft-lb
Bore 110 mm 4.33 in Bore 110 mm 4.33 in
Stroke 127 mm 5 in Stroke 127 mm 5 in
Displacement 7.2 L 439 in3 Displacement 7.2 L 439 in3
• Caterpillar engine with ACERT™ Technology – EPA Tier 3, • Caterpillar engine with ACERT Technology – EPA Tier 3,
EU Stage III Compliant EU Stage III Compliant
• These ratings apply at 1,800 rpm when tested under the specified • These ratings apply at 1,800 rpm when tested under the specified
standard conditions. standard conditions.
• Rating for net power advertised based on power available when • Rating for net power advertised based on power available when
the engine is equipped with alternator, air cleaner, muffler and the engine is equipped with alternator, air cleaner, muffler and
on-demand hydraulic fan drive at maximum fan speed. on-demand hydraulic fan drive at maximum fan speed.

Weights – 950H
Weights – 962H

Operating Weight 18 320 kg 40,376 lb Operating Weight 19 121 kg 42,141 lb

3 3 3 3
• For 3.1 m (4.0 yd ) general purpose bucket with BOCE. • For 3.4 m (4.45 yd ) general purpose bucket with BOCE.

Buckets – 950H
Buckets – 962H

Bucket Capacities 2.5-3.5 m3 3.25-4.5 yd3 Bucket Capacities 2.7-3.8 m3 3.5-5.0 yd3
Maximum Bucket Capacity 3.6 m3 4.7 yd3 Maximum Bucket Capacity 3.8 m3 5.0 yd3

Operating Specifications – 950H Operating Specifications – 962H

Breakout Force 150 kN 33,756 lb Breakout Force 141 kN 31,680 lb
Static Tipping Load, Full Turn (ISO) 10 811 kg 23,827 lb Static Tipping Load, Full Turn (ISO) 11 303 kg 24,913 lb
Static Tipping Load, Full Turn 11 540 kg 25,434 lb Static Tipping Load, Full Turn 12 038 kg 26,533 lb
(No Tire Deflection) (No Tire Deflection)
• For 3.1 m3 (4.0 yd3) general purpose bucket with BOCE. • For 3.4 m3 (4.45 yd3) general purpose bucket with BOCE.

Transmission – 950H
Transmission – 962H

Forward 1 6.9 km/h 4.3 mph Forward 1 7 km/h 4.4 mph

Forward 2 12.7 km/h 7.9 mph Forward 2 13 km/h 8.1 mph
Forward 3 22.3 km/h 13.9 mph Forward 3 22.6 km/h 14.0 mph
Forward 4 37 km/h 23.0 mph Forward 4 38 km/h 23.6 mph
Reverse 1 7.6 km/h 4.7 mph Reverse 1 7.6 km/h 4.7 mph
Reverse 2 13.9 km/h 8.6 mph Reverse 2 13.9 km/h 8.6 mph
Reverse 3 24.5 km/h 15.2 mph Reverse 3 24.5 km/h 15.2 mph
Reverse 4 40 km/h 24.9 mph Reverse 4 40 km/h 24.9 mph
• Maximum travel speeds (23.5-25 tires). • Maximum travel speeds (23.5-25 tires).

14
 Hydraulic System
Sound

Bucket/Work Tool System – 270 L/min 71 gal/min • The sound values indicated below are for specific operating
Pump Output conditions only. Machine and operator sound levels will vary at
Steering System Pump Type Piston different engine and/or cooling fan speeds. The cab was properly
Hydraulic Cycle Time – Raise 6.2 Seconds installed and maintained. The tests were conducted with the cab
doors and the cab windows closed. Hearing protection may be
Hydraulic Cycle Time – Dump 2.0 Seconds
needed when the machine is operated with a cabin that is not
Hydraulic Cycle Time – Lower 2.5 Seconds properly maintained, or when the doors and/or windows are
Hydraulic Cycle Time – Float 2.5 Seconds open for extended periods or in a noisy environment.
Hydraulic Cycle Time – Rack 2.7 Seconds • The declared dynamic operator Sound Pressure Level for a
standard machine configuration, measured according to the
• Implement System (Standard), Piston Pump – Rated at 2,100 rpm procedures specified in “ISO 6396:2008,” is 72 dB(A) with the
and 6900 kPa (1,000 psi). cooling fan speed set at maximum value.
• Cycle time with rated payload • The declared average exterior sound pressure level for a standard
machine configuration, measured according to the procedures
Brakes
specified in “SAE J88:2006 – Constant Speed Moving Test,” is
75 dB(A). The measurement was conducted under the following
Brakes Meets required standards.
conditions: distance of 15 m (49.2 ft), moving forward in an
• Meet ISO 3450-1985 standards. intermediate gear ratio, static hydraulic cycle (with no payload)
and with the cooling fan speed set at maximum value.
Axles
• The declared exterior sound power level for a standard machine
configuration, measured according to the procedures specified
Front Fixed front in “ISO 6395:2008,” is 111 dB(A) with the cooling fan speed set
Rear Oscillating ± 13° at maximum value.
Maximum Single-Wheel Rise and Fall 470 mm 18.5 in
Sound Level Information for Machines in Countries that Adopt
Tires the “EU Directives”
• The declared dynamic operator sound pressure level for a standard
Tires Choose from a variety machine configuration, measured according to the procedures
of tires to match your specified in “ISO 6396:2008,” is 69 dB(A) with a cooling fan speed
application. set at 70 percent of the maximum value.
• Choice of: • The declared sound power level that is labeled on the machine is
23.5R25 VSW BS L2 Radial 106 LWA. The measurement of the sound power level was made
23.5R25 VUT D2A BS L2 Radial according to the test procedures and conditions that are specified
23.5R25 XTLA MX L2 Radial in the European Union Directive “2000/14/EC” as amended by
23.5R25 VMT BS L3 Radial “2005/88/EC.”
23.5R25 XHA MX L3 Radial
23.5R25 XMINE MX L5 Radial Service Refill Capacities

750/65R25 XLD MX L3 Radial

Fuel Tank – Standard 264 L 70 gal
23.5-25 SGGL FS L2 Bias
Flexport Cooling System 42 L 11 gal
• NOTE: In certain applications (such as load and carry) the loader’s Crankcase 30 L 7.9 gal
productive capabilities might exceed the tires’ tonnes-km/h Transmission 34 L 9 gal
(ton-mph) capabilities. Caterpillar recommends that you consult a
Differentials and Final Drives – Front 36 L 9.5 gal
tire supplier to evaluate all conditions before selecting a tire model.
The 23.5-25 size range and other special tires are available on request. Differentials and Final Drives – Rear 36 L 9.5 gal
Hydraulic Tank 110 L 29 gal
Cab

ROPS/FOPS Meets SAE and

ISO standards.
• Caterpillar cab with integrated Rollover Protective Structure
(ROPS) are standard.
• ROPS meets SAE J1040 APR88 and ISO 3471:1994 criteria.
• Falling Objects Protective Structure (FOPS) meets SAE J231
JAN81 and ISO 3449:2005 version.

15
950H/962H Wheel Loaders Specifications

950H Dimensions
All dimensions are approximate and based on L3 Michelin XHA2 tires.

10

15

11
5
1 2
3 12
13

14 9 4 8
6 7

1 Height to top of ROPS/FOPS 3461 mm 11'4"

2 Height to top of exhaust pipe 3278 mm 10'8"
3 Height to top of hood 2448 mm 8'0"
4 Ground clearance with 23.5R25 397 mm 1'3"
5 B-Pin height – standard 3992 mm 13'1"
B-Pin height – high-lift 4490 mm 14'7"
6 Center line of rear axle to edge of counterweight 2001 mm 6.6"
7 Wheelbase 3350 mm 11'0"
8 B-Pin height @ carry – standard 624 mm 2'0"
B-Pin height @ carry – high lift 748 mm 2'5"
9 Center line of rear axle to hitch 1675 mm 5'5"
10 Rack back @ maximum lift 59.5 degrees
11 Dump angle @ maximum lift 48.2 degrees
12 Rack back @ carry 49.4 degrees
13 Rack back @ ground 41 degrees
14 Height to center line of axle 748 mm 2'5"
15 Lift arm clearance @ standard lift 3916 mm 12'8"
Lift arm clearance @ high lift 4414 mm 14'5"

Tires
Tread width for 23.5-25 is 2140 mm (7'0")
Width over tires Change in vertical Change in Change in static
dimensions operating weight tipping load
mm inches mm inches kg lb kg lb
23.5R25 VSW BS L2 Radial 2862 113 6 0.2 20 44 14 31
23.5R25 VUT D2A BS L2 Radial 2866 113 10 0.4 –41 –90 –29 –64
23.5R25 XTLA MX L2 Radial 2801 110 7 0.3 –112 –247 –79 –174
23.5R25 VMT BS L3 Radial 2851 112 3 0.1 124 273 88 194
23.5R25 XHA MX L3 Radial 2784 110 0 0.0 0 0 0 0
23.5R25 XMINE MX L5 Radial 2807 111 26 1.0 872 1,923 619 1,365
750/65R25 XLD MX L3 Radial 2879 113 7 0.3 460 1,014 326 719
23.5-25 SGGL FS L2 Bias 2834 112 14 0.6 –472 –1,041 –335 –739
16
962H Dimensions

All dimensions are approximate and based on L3 Michelin XHA2 tires.

10

15

11
5
1 2
3 12
13

14 9 4 8
6 7

1 Height to top of ROPS/FOPS 3461 mm 11'4"

2 Height to top of exhaust pipe 3278 mm 10'8"
3 Height to top of hood 2448 mm 8'0"
4 Ground clearance with 23.5R25 397 mm 1'3"
5 B-Pin height – standard 4182 mm 13'7"
B-Pin height – high-lift 4490 mm 14'7"
6 Center line of rear axle to edge of counterweight 2001 mm 6.6"
7 Wheelbase 3350 mm 11'0"
8 B-Pin height @ carry – standard 664 mm 2'2"
B-Pin height @ carry – high lift 748 mm 2'5"
9 Center line of rear axle to hitch 1675 mm 5'5"
10 Rack back @ maximum lift 59.5 degrees
11 Dump angle @ maximum lift 48.2 degrees
12 Rack back @ carry 48.5 degrees
13 Rack back @ ground 40 degrees
14 Height to center line of axle 748 mm 2'5"
15 Lift arm clearance @ standard lift 4002 mm 13'1"
Lift arm clearance @ high lift 4414 mm 14'5"

Tires
Tread width for 23.5-25 is 2140 mm (7'0")
Width over tires Change in vertical Change in Change in static
dimensions operating weight tipping load
mm inches mm inches kg lb kg lb
23.5R25 VSW BS L2 Radial 2862 113 6 0.2 20 44 14 31
23.5R25 VUT D2A BS L2 Radial 2866 113 10 0.4 –41 –90 –29 –64
23.5R25 XTLA MX L2 Radial 2801 110 7 0.3 –112 –247 –79 –174
23.5R25 VMT BS L3 Radial 2851 112 3 0.1 124 273 88 194
23.5R25 XHA MX L3 Radial 2784 110 0 0.0 0 0 0 0
23.5R25 XMINE MX L5 Radial 2807 111 26 1.0 872 1,923 619 1,365
750/65R25 XLD MX L3 Radial 2879 113 7 0.3 460 1,014 326 719
23.5-25 SGGL FS L2 Bias 2834 112 14 0.6 –472 –1,041 –335 –739

17
950H Operating Specifications – Standard

Bucket Type Material Handling – Pin On

Bolt-On Teeth and
Bolt-On Teeth and Bolt-On Teeth and
Edge Type Edges Segments
Edges Segments Edges Segments
Capacity – Rated (§) m3 3.20 3.20 3.40 3.40 3.60 3.60
yd3 4.19 4.19 4.45 4.45 4.71 4.71
Capacity – Rated @ 110% Fill Factor m3 3.50 3.50 3.70 3.70 4.00 4.00
yd3 4.60 4.60 4.90 4.90 5.20 5.20
Width (§) mm 2927 2994 2927 2994 2927 2994
ft/in 9'7" 9'9" 9'7" 9'9" 9'7" 9'9"
Dump Clearance at Maximum Lift and 45° Discharge (§) mm 2756 2631 2721 2596 2686 2560
ft/in 9'0" 8'7" 8'11" 8'6" 8'9" 8'4"
Reach at Maximum Lift and 45° Discharge (§) mm 1255 1358 1291 1393 1326 1428
ft/in 4'1" 4'5" 4'2" 4'6" 4'4" 4'8"
Reach at Level Lift Arm and Bucket Level (§) mm 2672 2833 2722 2883 2772 2933
ft/in 8'9" 9'3" 8'11" 9'5" 9'1" 9'7"
Digging Depth (§) mm 97 97 97 97 97 97
in 3.8" 3.8" 3.8" 3.8" 3.8" 3.8"
Overall Length mm 8112 8286 8162 8336 8212 8386
ft/in 26'8" 27'3" 26'10" 27'5" 27'0" 27'7"
Overall Height with Bucket at Maximum Lift mm 5490 5490 5539 5539 5589 5589
ft/in 18'1" 18'1" 18'3" 18'3" 18'5" 18'5"
Loader Clearance Circle with Bucket at Carry Position (§) mm 13 387 13 551 13 415 13 580 13 443 13 608
ft/in 44'0" 44'6" 44'1" 44'7" 44'2" 44'8"
Static Tipping Load, Straight (ISO)* kg 12 307 12 168 12 214 12 074 12 127 11 986
lb 27,125 26,818 26,921 26,612 26,729 26,418
Static Tipping Load, Straight (No Tire Deflection)* kg 13 020 12 879 12 929 12 787 12 845 12 702
lb 28,696 28,386 28,497 28,184 28,311 27,997
Static Tipping Load, Articulated (ISO)* kg 10 624 10 485 10 536 10 396 10 454 10 312
lb 23,417 23,109 23,223 22,914 23,040 22,729
Static Tipping Load, Articulated (No Tire Deflection)* kg 11 340 11 199 11 254 11 112 11 174 11 031
lb 24,993 24,683 24,804 24,492 24,628 24,313
Breakout Force** (§) kN 144 143 138 137 133 132
lb 32,489 32,223 31,199 30,934 29,997 29,733
Operating Weight* kg 18 352 18 460 18 400 18 508 18 446 18 554
lb 40,446 40,684 40,552 40,790 40,653 40,892

* Static tipping loads and operating weights shown are based on a global machine configuration with Michelin 23.5R25 XHA2 L3 Radial
tires, full fluids, operator, standard counterweight, standard linkage, cold start, roading fenders, product link, open differential axles
(front/rear), power train guard, secondary steering, and sound suppression.
** Measured 102 mm (4") behind tip of cutting edge with bucket hinge pin as pivot point in accordance with SAE J732C.
(§) Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers, including
SAE Standard J732C governing loader ratings.
(ISO) Full compliance to ISO 14397-1 (2007) Sections 1 thru 6, which requires 2% verification between calculations and testing.
(No Tire Deflection) Compliance to ISO 14397-1 (2007) Sections 1 thru 5.

19
950H/962H Wheel Loaders Specifications

950H Operating Specifications

High Lift
Change in
Specs
Capacity – Rated (§) m3
yd3
Capacity – Rated @ 110% Fill Factor m3
yd3
Width (§) mm
ft/in
Dump Clearance at Maximum Lift and 45° Discharge (§) mm 495
ft/in 1'7"
Reach at Maximum Lift and 45° Discharge (§) mm 67
ft/in 0'2"
Reach at Level Lift Arm and Bucket Level (§) mm 405
ft/in 1'3"
Digging Depth (§) mm 21
in 0.8"
Overall Length mm 605
ft/in 2'0"
Overall Height with Bucket at Maximum Lift mm 496
ft/in 1'8"
Loader Clearance Circle with Bucket at Carry Position (§) mm 391
ft/in 1'4"
Static Tipping Load, Straight (ISO)* kg (341)
lb (751)
Static Tipping Load, Straight (No Tire Deflection)* kg (398)
lb (878)
Static Tipping Load, Articulated (ISO)* kg (416)
lb (917)
Static Tipping Load, Articulated (No Tire Deflection)* kg (458)
lb (1,011)
Breakout Force** (§) kN (8)
lb (1,892)
Operating Weight* kg 1271
lb 2,800

* Static tipping loads and operating weights shown are based on a global machine configuration with Michelin 23.5R25 XHA2 L3 Radial
tires, full fluids, operator, standard counterweight, standard linkage, cold start, roading fenders, product link, open differential axles
(front/rear), power train guard, secondary steering, and sound suppression.
** Measured 102 mm (4") behind tip of cutting edge with bucket hinge pin as pivot point in accordance with SAE J732C.
(§) Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers, including
SAE Standard J732C governing loader ratings.
(ISO) Full compliance to ISO 14397-1 (2007) Sections 1 thru 6, which requires 2% verification between calculations and testing.
(No Tire Deflection) Compliance to ISO 14397-1 (2007) Sections 1 thru 5.

20
950H/962H Wheel Loaders Specifications

962H Operating Specifications – Standard

Bucket Type General Purpose – Pin On

Bolt-On Teeth and
Bolt-On Teeth and Bolt-On Teeth and
Edge Type Edges Segments
Edges Segments Edges Segments
Capacity – Rated (§) m3 3.10 3.10 3.40 3.40 3.60 3.60
yd3 4.05 4.05 4.45 4.45 4.71 4.71
Capacity – Rated @ 110% Fill Factor m3 3.40 3.40 3.70 3.70 4.00 4.00
yd3 4.50 4.50 4.90 4.90 5.20 5.20
Width (§) mm 2927 2994 2927 2994 2927 2994
ft/in 9'7" 9'9" 9'7" 9'9" 9'7" 9'9"
Dump Clearance at Maximum Lift and 45° Discharge (§) mm 3046 2928 2981 2862 2935 2816
ft/in 9'11" 9'7" 9'9" 9'4" 9'7" 9'2"
Reach at Maximum Lift and 45° Discharge (§) mm 1269 1380 1321 1431 1357 1467
ft/in 4'1" 4'6" 4'4" 4'8" 4'5" 4'9"
Reach at Level Lift Arm and Bucket Level (§) mm 2727 2888 2812 2973 2872 3033
ft/in 8'11" 9'5" 9'2" 9'9" 9'5" 9'11"
Digging Depth (§) mm 90 90 90 90 90 90
in 3.5" 3.5" 3.5" 3.5" 3.5" 3.5"
Overall Length mm 8291 8464 8376 8549 8436 8609
ft/in 27'3" 27'10" 27'6" 28'1" 27'9" 28'3"
Overall Height with Bucket at Maximum Lift mm 5515 5515 5719 5719 5777 5777
ft/in 18'2" 18'2" 18'10" 18'10" 19'0" 19'0"
Loader Clearance Circle with Bucket at Carry Position (§) mm 13 478 13 645 13 527 13 696 13 562 13 732
ft/in 44'3" 44'10" 44'5" 45'0" 44'6" 45'1"
Static Tipping Load, Straight (ISO)* kg 13 346 13 208 13 181 13 041 13 060 12 919
lb 29,416 29,110 29,052 28,744 28,784 28,474
Static Tipping Load, Straight (No Tire Deflection)* kg 14 065 13 925 13 903 13 762 13 784 13 642
lb 30,999 30,691 30,643 30,332 30,380 30,067
Static Tipping Load, Articulated (ISO)* kg 11 459 11 320 11 303 11 163 11 189 11 048
lb 25,255 24,950 24,913 24,605 24,661 24,351
Static Tipping Load, Articulated (No Tire Deflection)* kg 12 190 12 050 12 038 11 897 11 926 11 784
lb 26,867 26,559 26,533 26,221 26,285 25,972
Breakout Force** (§) kN 151 150 141 139 134 133
lb 33,973 33,715 31,680 31,423 30,214 29,958
Operating Weight* kg 19 046 19 154 19 121 19 229 19 179 19 287
lb 41,976 42,214 42,141 42,379 42,269 42,507

* Static tipping loads and operating weights shown are based on a global machine configuration with Michelin 23.5R25 XHA2 L3 Radial
tires, full fluids, operator, standard counterweight, standard linkage, cold start, roading fenders, product link, open differential axles
(front/rear), power train guard, secondary steering, and sound suppression.
** Measured 102 mm (4") behind tip of cutting edge with bucket hinge pin as pivot point in accordance with SAE J732C.
(§) Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers, including
SAE Standard J732C governing loader ratings.
(ISO) Full compliance to ISO 14397-1 (2007) Sections 1 thru 6, which requires 2% verification between calculations and testing.
(No Tire Deflection) Compliance to ISO 14397-1 (2007) Sections 1 thru 5.

22
962H Operating Specifications – Standard

Bucket Type Material Handling – Pin On

Bolt-On Teeth and
Bolt-On Teeth and Bolt-On Teeth and
Edge Type Edges Segments
Edges Segments Edges Segments
Capacity – Rated (§) m3 3.40 3.40 3.60 3.60 3.80 3.80
yd3 4.45 4.45 4.71 4.71 4.97 4.97
Capacity – Rated @ 110% Fill Factor m3 3.70 3.70 4.00 4.00 4.20 4.20
yd3 4.90 4.90 5.20 5.20 5.50 5.50
Width (§) mm 2927 2994 2927 2994 2927 2994
ft/in 9'7" 9'9" 9'7" 9'9" 9'7" 9'9"
Dump Clearance at Maximum Lift and 45° Discharge (§) mm 2911 2786 2876 2750 2833 2707
ft/in 9'6" 9'1" 9'5" 9'0" 9'3" 8'10"
Reach at Maximum Lift and 45° Discharge (§) mm 1241 1343 1276 1378 1319 1421
ft/in 4'0" 4'4" 4'2" 4'6" 4'3" 4'7"
Reach at Level Lift Arm and Bucket Level (§) mm 2822 2983 2872 3033 2933 3094
ft/in 9'3" 9'9" 9'5" 9'11" 9'7" 10'1"
Digging Depth (§) mm 98 98 98 98 98 98
in 3.8" 3.8" 3.8" 3.8" 3.8" 3.8"
Overall Length mm 8392 8565 8442 8615 8503 8676
ft/in 27'7" 28'2" 27'9" 28'4" 27'11" 28'6"
Overall Height with Bucket at Maximum Lift mm 5729 5729 5779 5779 5828 5828
ft/in 18'10" 18'10" 19'0" 19'0" 19'2" 19'2"
Loader Clearance Circle with Bucket at Carry Position (§) mm 13 540 13 709 13 569 13 739 13 605 13 776
ft/in 44'6" 45'0" 44'7" 45'1" 44'8" 45'3"
Static Tipping Load, Straight (ISO)* kg 13 039 12 900 12 949 12 809 12 835 12 694
lb 28,738 28,431 28,540 28,232 28,288 27,978
Static Tipping Load, Straight (No Tire Deflection)* kg 13 746 13 605 13 659 13 518 13 547 13 405
lb 30,296 29,987 30,105 29,794 29,859 29,546
Static Tipping Load, Articulated (ISO)* kg 11 180 11 040 11 094 10 955 10 987 10 846
lb 24,640 24,334 24,453 24,144 24,215 23,905
Static Tipping Load, Articulated (No Tire Deflection)* kg 11 900 11 760 11 818 11 677 11 712 11 570
lb 26,228 25,919 26,047 25,736 25,815 25,502
Breakout Force** (§) kN 139 138 134 133 128 127
lb 31,403 31,144 30,195 29,936 28,825 28,568
Operating Weight* kg 19 126 19 234 19 172 19 280 19 228 19 336
lb 42,152 42,390 42,254 42,492 42,377 42,615

* Static tipping loads and operating weights shown are based on a global machine configuration with Michelin 23.5R25 XHA2 L3 Radial
tires, full fluids, operator, standard counterweight, standard linkage, cold start, roading fenders, product link, open differential axles
(front/rear), power train guard, secondary steering, and sound suppression.
** Measured 102 mm (4") behind tip of cutting edge with bucket hinge pin as pivot point in accordance with SAE J732C.
(§) Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers, including
SAE Standard J732C governing loader ratings.
(ISO) Full compliance to ISO 14397-1 (2007) Sections 1 thru 6, which requires 2% verification between calculations and testing.
(No Tire Deflection) Compliance to ISO 14397-1 (2007) Sections 1 thru 5.

23
950H/962H Standard Equipment

Standard Equipment

Standard equipment may vary. Consult your Cat dealer for details.

ELECTRICAL • Controls, electro-hydraulic, OTHER

• Alarm, back-up lift and tilt function • Automatic bucket positioner
• Alternator, 115-amp brushed • Heater and defroster • Counterweight
• Batteries, maintenance free (2) 1,400 CCA • Horn, electric (console) • Couplings, Cat O-ring face seal
• Ignition key; start/stop switch • Light, dome (cab) • Doors, service access (locking)
• Lighting system, halogen (6 total) • Lunch box, beverage holders and • Ecology drains, engine, transmission
• Main disconnect switch personal tray and hydraulics
• Starter, electric, heavy-duty • Mirror, rearview (internally mounted) • Fenders, steel (front and rear)
• Starting and charging system (24-volt) • Mirrors, external • Guard, airborne debris
• Receptacle, starting, 24-volt • Seat, Cat Comfort (cloth) with air suspension • Hitch, drawbar with pin
• Seat belt, retractable, 51 mm (2 in) wide • Hood, non-metallic, power tilting
OPERATOR ENVIRONMENT • Steering column, adjustable angle • Hoses, Cat XT
• Air conditioner (steering wheel – command control steering) • Hydraulic oil cooler
• Bucket/work tool function lockout and length (command control steering) • Kickout, lift and tilt, automatic
• Cab, pressurized and sound-suppressed • Wet-arm wipers and washers, front and rear (in-cab adjustable)
ROPS/FOPS – Intermittent front wiper • Linkage, Z-bar, cast cross tube/tilt lever
• Radio-ready (entertainment) includes • Window, sliding (left and right side) • Oil sampling valves
antenna, speakers and converter • Product Link ready
(12-volt, 10-amp) POWER TRAIN • Remote diagnostic pressure taps
• Coat hook • Brakes, full hydraulic enclosed wet-disc • Remote FNR
• Computerized monitoring system with Integrated Braking System (IBS)
• Service center, electrical and hydraulic
• Instrumentation, gauges: and brake wear indicator
• Sight gauges:
– Digital gear range indicator • Engine, Cat C7 with ACERT Technology
and ATAAC – Engine coolant
– Engine coolant temperature – Hydraulic oil
• Fan, radiator, electronically controlled,
– Fuel level – Transmission oil level
hydraulically driven, temperature sensing,
– Hydraulic oil temperature on demand • Sun visor, front
– Speedometer/tachometer • Filters, fuel, primary/secondary • Steering, load sensing
– Transmission oil temperature • Filters, engine air, primary/secondary
• Instrumentation, warning indicators: • Fuel priming pump (electric) TIRES, RIMS, WHEELS
– Air inlet heater • Fuel/water separator • A tire must be selected from the mandatory
– Axle oil temperature • Muffler, sound suppressed attachments section. Base machine price
– Electrical, alternator output includes an allowance based on a premium
• Radiator, unit core
– Engine inlet manifold temperature radial tire.
• Starting aid, air inlet heater
– Engine oil pressure • Switch, transmission neutralizer lockout
– Fuel level ANTIFREEZE
• Torque converter • Premixed 50% concentration of
– Fuel pressure, hi/low • Transmission, automatic, planetary Extended Life Coolant with freeze
– Parking brake powershift (4F/4R) protection to –34° C (–29° F)
– Primary steering oil pressure
– Service brake oil pressure
– Transmission filter bypass

26