VAG Non-Return Valves
VAG SKR Slanted Seat Tilting disk Check Valve
Body
Shaft
Bearing bush
Disk
Seat
Technical details Product features
š Nominal pressures PN 10, 16 š Due to the tilting disk, the stroke is shortened by about
š Nominal diameters DN 200 … 1400 30°. This results in shorter closing times, less backflow and
reduced slamming of the disk.
š Fields of application: drinking water, preclarified wastewater
š disk swings and opens easily even at low flow velocities. This
š Face-to-face length to EN 558, basic series 14 results in low headloss and pumping capacity (saving energy).
š Recommended flow velocity: min. 1,6 m/s š Minimum space required for installation due to short face-to-
š Standard version: body and disk made of ductile iron face length and no external assembly components.
EN-GJS-400-15 (GGG-40), seat made of microfinished high- š No external shaft bushes due to the slanted seat design, no
alloy weld overlay lever and weight required for assisted closing. Therefore no
š Inside and outside epoxy coating frictional sealing required and no hazardous external moving
parts.
š Special versions:
- With internal damping unit š Maintenance-free metallic sealing by way of a microfinished
high-alloy weld overlay which ensures corrosion and wear
- With blanking plate (prepared for internal damping unit)
resistant sealing faces.
- With mechanical position indicator
- With limit switches š Additional internal damping units for the reduction of pressure
surges – can also be retrofitted. Approximately 10-15 %
- With internal rubber lining
before the final closed position, the damper takes effect and
- Welded or forged version the disk moves slowly into the seat dampening the pressure
- For hot water up to 150 °C surge and without slamming.
- Stainless steel version
- Nominal pressure PN 25
VAG TOP-STOP® Non-Return Valve
Flow guide
Circular diaphragm
Plug bolt
Inlet body
Outlet body
Technical details Product features
š Nominal pressures PN 10, 16 š Optimum damping of pressure surges caused by quick flow
š Nominal diameters DN 40 … 400 reversal due to pre-tensioned elastic diaphragm.
š Fields of application: drinking water, service water š Low space requirement due to compact design.
š Face-to-face length to EN 558, basic series 48 š At flow reversal, the circular diaphragm closes quickly,
emitting little noise. Therefore no metallic slamming while the
š Recommended flow velocity: min. 1,5 m/s (horizontal valve is closing.
installation) / min. 1,5 m/s (vertical installation)
š Quick and safe response and extremely short closing times
š Standard model: body and flow guide made of ductile iron due to almost inertial less diaphragm.
EN-GJS-400-15 (GGG-40) with epoxy coating, circular
diaphragm made of EPDM š Pre-formed diaphragm ensures safe and reliable operation in
any installation position.
š Epoxy coating to GSK guidelines
š No mechanic moving parts internally or externally. This
reduces maintenance and ensures optimum accident
prevention in the operating area.
š Maintenance-friendly due to easy replacement of the
diaphragm.
š Integrated plugs allow the simple assembly of a bypass on
site.
VAG RETO-STOP Non-Return Valve
Cover
Seal
Suspension of the Disk
Disk with rubber joint
Body
Plug bolt
Technical details Product features
š Nominal pressure: PN 10, 16 š The low-resistance disk suspension ensures the opening of
š Nominal diameter: DN 40 … 300 the valve even at low differential pressures.
š Fields of application: drinking water, service water, š Low pressure loss due to the optimised shape of the body
wastewater with a 90 % opening degree of the disk.
š Face-to-face length to EN 558, basic series 48 š The smooth disk with no sharp edges minimises the deposit
of dirt particles and makes the valve also suitable for polluted
š Recommended flow velocity: min. 1,5 m/s (horizontal media (wastewater).
installation) / min. 2,0 m/s (vertical installation)
š No friction of the bearings due to integrated suspension of
š Standard model: body and cover made of ductile iron the disk and therefore no wear.
EN-GJS-400-15 (GGG-40), disk made of ductile iron
EN-GJS-400-15 (GGG-40), EPDM vulcanised all over š The suspension of the disk with pre-formed rubber joint
accelerates and supports the closing movement of the disk to
š Epoxy coating to GSK guidelines reduce pressure surges.
š Special versions: š The rubber joint prevents the jamming or clogging of the disk
- With lifting device G ¾’’ suspension even in polluted media.
š For maintenance purposes the disk can be reversed and used
on both sides (integrated spare part), which doubles the life
expectancy of the valve.
š Maintenance-friendly due to large cover for easy maintenance
of the disk.
š An optional lifting device allows lifting of the disk allowing
filling or purging of the pipeline.
š The optional bypass valve allows bypassing even at full
operating pressure.
VAG LIMU-STOP® Non-Return Valve
Shaft
Lever and weight
Suspension eye
Shaft bearing Cleaning cover
Disk
Body
Disk seal
Technical details Product features
š Nominal pressure PN 10, 16 š Little pressure loss due to optimised body design with a 90 %
š Nominal diameter DN 50 … 300 opening degree of the disk.
š Fields of application: service water, wastewater š Safe and reliable function due to flexible and dampened
double bearing of the disk.
š Face-to-face length to EN 558, basic series 48
š Low-wear bearing of the shaft ensured by low-friction bronze
š Recommended flow velocity: min. 1,5 m/s (horizontal bushes.
installation) / min. 2,0 m/s (vertical installation)
š Piggable in flow direction due to the large opening degree of
š Standard version: with lever and weight body and cover the disk.
made of ductile iron EN-GJS-400-15 (GGG-40), disk made
of stainless steel grade 1.4308, disk seal made of NBR, shaft š Large cleaning cover and thus fast, easy and maintenance-
made of stainless steel grade 1.4057, shaft bearing made of friendly cleaning of the disk by turning it out and without the
zinc-free bronze need of disassembly.
š Epoxy coating to GSK guidelines š Easy replacement of the disk ensured by O-ring inserted in
the disk.
š Special versions:
š Shortened stroke due to the slanted seat of the disk. This
- With lever and weight and wire guard
results in a reduced closing time, less backflow and less
- With internal shaft intensive impact of the disk.
š Very long service life due to dampened limit stop of the disk
in the body.
š Easy assembly thanks to suspension eyes.
VAG RETA Check Valve
Cover
Seal
Suspension of the Disk
Body
Disk
Technical details Product features
š Nominal pressures PN 10, 16 š Low pressure loss due to the optimised shape of the body
š Nominal diameters DN 40 … 250 with a 90% opening degree of the disk.
š Fields of application: drinking water, service water š Can be adapted to different plant conditions as it can be
used in both horizontal and vertical (flow from bottom to top)
š Face-to-face length to EN 558, basic series 48 pipelines.
š Recommended flow velocity: min. 1,5 m/s (horizontal š Maintenance-friendly due to cover for easy replacement of
installation) / min. 2,0 m/s (vertical installation) the disk.
š Standard version: resilient-seated, body, cover and disk made š Available with or without lever and weight for optical position
of cast iron EN-GJL-250 (GG-25) indication.
š Inside and outside epoxy coating š The optional bypass valve allows operation even at full
š Special versions: operating pressure.
- With lever and weight
- Metallic sealing with synthetic resin coating for higher
temperatures
VAG AW disk Check Valve
Cover
Body
Disk
Lever and weight
Technical details Product features
š Nominal pressure PN 10, 16 š Resistance to media due to the use of premium-quality
š Nominal diameter DN 50 … 800 materials.
š Field of application: wastewater š Depending on its type, the valve can be used for various plant
conditions as well as in horizontal or vertical pipelines.
š Face-to-face length to EN 558, basic series 48
š Maintenance-friendly due to large inspection cover.
š Recommended flow velocity: min. 1,5 m/s (horizontal
installation) / min. 2,0 m/s (vertical installation)
š Standard version: resilient-seated, with lever and weight,
body, cover and disk made of ductile iron EN-GJS-400-15
(GGG-40), shaft made of stainless steel 1.4057, shaft bushing:
O-rings made of NBR
š Inside and outside epoxy coating
š Special versions:
- Metallic sealing
- With factory-mounted wire guard
- Horizontal / vertical type
VAG KRV Ball Check Valve
Cover
Seal
Ball
Free passage
Body
Technical details Product features
š Nominal pressures PN 10, 16 š The ball is lifted into the dome by the flow and releases the
š Nominal diameters DN 50 … 200 full passage.
š Fields of application: service water, wastewater š Free flow cross-section without any edges provides optimum
suitability for use with polluted media (wastewater) and
š Face-to-face length to EN 558, basic series 48 minimises the risk of clogging.
š Recommended flow velocity: min. 3,0 m/s š Low pressure loss due to optimised body shape with free
š Standard model: body and cover made of ductile iron passage and thus low flow resistance.
EN-GJS-400-15 (GGG-40), ball core made of aluminium and š Prevents back flow even at low differential pressure by
NBR rubber coated all over making use of the ball-check principle.
š Inside and outside epoxy coating to GSK guidelines š The ball-check principle allows shut-off in all directions.
š Maintenance-friendly due to large opening for cleaning the
dome.
š No mechanically moved parts on the inside and outside. This
reduces wear and maintenance work and ensures optimum
accident prevention in the operating area.
VAG ZETKA Non-Return Valve
Seal
Disk reinforcement
Pin
Disk
Body outlet
Body inlet
Technical details Product features
š Nominal pressures PN 10, 16 š Short closing time due to design of the disk.
š Nominal diameters DN 40 … 300 š Applicable for low pressure differences.
š Fields of application: drinking water, service water š Easy installation between pipeline flanges.
š Face-to-face length to EN 558, basic series 16
š Recommended flow velocity: max. 3,5 m/s
š Standard model: body parts made of ductile iron
EN-GJS-400-15 (GGG-40) and cast iron EN-GJL-250 (GG-25),
check valve disk made of steel 1.0570 ), EPDM vulcanised all
over
š Inside and outside epoxy coating
š Special versions:
- Disk NR vulcanised all over
VAG CHECKtronic Pump Safety Valve
Pump start-up
The electric actuator keeps the valve closed
against the pump starting up. When the pump has
reached its operating speed, the electric actuator
slowly opens the valve and checks how fast the
water column accelerates to flow velocity to
minimise pressure surges at pump start-up.
Electric actuator
Pump operation
During normal pump operation, the valve is in fully
open position.
Threaded stem adaptor
Spring
Spring seat
Stem Normal switch-off of the pump
While the pump is in operation, the electric actuator
starts closing the valve slowly to check how fast
Disk seat ring
the water column decelerates to minimise the
Cover
separation of the column and pressure surges.
Disk The pump motor switches off when the valve
disk has completely moved into the seat and the
Body seat medium has stopped flowing.
Body Pump or power failure
If the valve is in open position and if the power
supply of the pump fails, the integrated spring-
loaded shut-off control is diskonnected
automatically from the electric actuator and quickly
closes the valve to prevent return flow through the
pump.
Technical details Product features
š Nominal pressures PN 10, 16, 25 š The electric actuator allows the start-up of the pump against
š Nominal diameters DN 80 ... 600 the closed valve; slow opening and closing for normal pump
operation.
š Fields of application: Water, wastewater
š In the event of a failure of the pump, the motor or the
š Standard version: Body, cover and disk made of ductile iron power supply, closing of the spring-loaded disk is possible
ASTM A536 grade 65-45-12 (EN-GJS-500-7), body seat independent of the electric actuator.
made of stainless steel type 316 (1.4401), disk seat ring made
of ultra-high molecular weight polyethylene (UHMWPE) ASTM š The opening and closing times of the electrically operated
D-4020 valve can be adjusted in dependence of the operating
conditions, which allows the optimum control of pressure
š With electric actuator surges.
š Inside and outside epoxy coating š Any kind of maintenance work can be performed from above
š Special versions: through the body, eliminating the need to dismantle the valve
- Higher head on request from the pipeline.
- Other materials on request š Seat, stem and internal fasteners made of corrosion-resistant
- Bigger sizes on request stainless steel, which ensures a long service life.
- Various flange systems available upon request š The replaceable, abrasion-resistant UHMWPE seat ensures
- With hydraulic damping for controlled closing in the event permanent leak-tightness in the seat.
of a power failure
VAG HADE® Flap Valve
Frame
Seal
Flanged connection
Cover
Eyelet Example: Type PTK-F (flanged connection)
Technical details Product features
š Nominal diameters DN 150 … 1000 š The low-resistance flap suspension ensures the opening of
š Fields of application: gravity lines and pump lines, wastewater the valve even at low differential pressure.
(storm water, mixed water) š For diskharge above and below the external water level.
š Vertical or slanted disk š Corrosion-resistant due to the use of rust-proof materials.
š Standard version: body made of PE-HD, for clowelling to even š Equipped with an attachment possibility for manual opening
concrete walls of the flap valve.
š Installation on the wall or end of pipeline š Damping of the flap via the circumferential seal.
š Special versions: š Maintenance-friendly due to few moved components.
- For larger nominal diameters, e.g. also rectangular cross- š Low weight due to the PE-HD material used.
sections, available upon request
š Wide range of applications due to various attachment
- For PVC and PE pipes
possibilities (fixing by dowels, insertion, flange mounting).
- For insertion into concrete pipes
- With flange
Reference projects
Wastewater pumping station
Birkenheide, Germany
VAG RETO-STOP Non-Return
Valves
VAG ZETA® Knife Gate Valves
Water treatment plant
Gredice, Croatia
VAG TOP-STOP ® Diaphragm Non-
Return Valves
VAG EKO ®plus Gate Valves
VAG EKN ® Butterly valves
VAG DUOJET® Automatic Air Valves
Flood protection
Prague, Czech Republic
VAG HADE® Flap Valves
VAG ZETA® Knife Gate Valves
Cooling-water circuit of refinery
(GLWLRQB
Plock, Poland
VAG SKR Slanted Seat Tilting disk
Check Valves
www.vag-group.com
[email protected]
For detailed information about nominal diameters, nominal pressures and types
WKHWHFKQLFDOGRFXPHQWDWLRQ.$7$LVDXWKRULWDWLYHš7KHSLFWXUHVDUHQRQELQGLQJ
