https://www.pharmaceuticalsky.
com/
Skip testing is a process employed to reduce the analytical drugs testing burden and lends
itself to processes with high frequency batch production. Rather than test all batches within
a given interval, pre-selected batches are assessed and the other batches ‘skipped’. This
reduction is justified as it is shown that there is a low risk of any batches failing
specification.
Periodic Testing or Skip Testing
• Skip or periodic testing is defined by The International Council for Harmonization of
Technical Requirements for Pharmaceuticals for Human Use (ICH) as conducting
‘‘specified tests at release on pre-selected batches and/or at predetermined intervals,
rather than on a batch-to-batch basis, with the understanding that those batches not
tested should still meet all the acceptance criteria established for that product’’.
• All pharmaceutical industries have their internal Standard Operating Procedure (SOP)
for the implementation of periodic or skip testing. The frequency for the
implementation of Periodic testing or Skip testing may be one batch per twenty
batches or the first batch manufactured every year (whichever is earlier) and it may
vary from one company to another.
Implementation
• Skip testing must only be implemented for low risk scenarios. This could be based
upon a strong scientific rationale detailing why the skip-test is inherently unlikely to
fail and/or using process capability data to show that the process is under control.
Ongoing verification should also be applied to confirm the process is still capable of
meeting specification. In addition, the following should be documented prior to
implementation:
1. Alternative measures which are in place to control the quality attribute if it is
no longer to be confirmed through testing every batch;
2. Scientific rationale which shows that the quality attribute has a low impact on
safety and/or efficacy;
3. Scientific rationale (supported by risk assessment) which demonstrates that
the attribute is not critical to quality (i.e., it is not a Critical Quality Attribute )
4. Justification of skip testing intervals and batch selection
5. Process to be followed if a batch selected for testing fails to meet specification.
• These tests can be implemented for
1. Active Pharmaceutical Ingredients (APIs),
2. Excipients,
3. Packing materials
4. In-process testing of finished products analysis.
https://www.pharmaceuticalsky.com/ Page 1 of 7
https://www.pharmaceuticalsky.com/
5. Skip or periodic testing cannot be implemented for finished product testing.
• Implementation of PT or ST for API, excipient and packaging material can be
approached according to SOP which would be available for an audit by the
regulatory agencies.
• The implementation of PT for in-process testing of finished product can be
undertaken only after seeking concurrence from the regulatory either during the
review of a marketing authorization application or after approval of the application.
• A suitable supplement or variation needs to be submitted to the agency for its
review if PT is to be implemented for in-process testing.
Implementation of the PT or ST concept for the important test
Raw Materials
API Description (DS), Identification (ID), Loss on Drying
(LOD), water content, particle size, bulk density, assay,
purity test and microbial test.
Excipients DS, ID, particle size, bulk density, powder fineness and
microbial test
Packing Materials
Al. foil paper back DS, ID*, Total grammage and width
Al. foils plain DS, ID* and width
Al. foils printed DS, ID*, width, printing matter and shade
Ampoules DS, dimensions and weight*
Closures Type of closure, dimensions, heat seal and pulp lines
Cold formable foil DS, ID*, width and shade
Laminated Al foil DS, ID*, dimensions and printing
pouch
Molecular sieves DS and adsorption capacity
Plastic containers DS and physical parameters
Poly Bag DS and dimensions
Purified cotton/Rayon DS, ID, water content
filter
PVC and PVDC DS, ID, width and shade*
PVC Aclar DS, ID*, width, total grammage
https://www.pharmaceuticalsky.com/ Page 2 of 7
https://www.pharmaceuticalsky.com/
Rubber stopper DS, dimensions and absorbance
Silica gel bag DS and weight
Silica gel canister DS, dimension and adsorption capacity
Vials DS, dimensions, weight*
Carton DS, printing matter and shade
Leaflets DS and printing
Self-adhesive label DS, Text and Color
* If applicable this test can be recommended
Note: Key identification test only required.
Skip Testing Strategy
• The proposed strategy for implementing skip-testing implementation can be broken
down into a four-stage procedure.
1. Selection of attributes via risk assessment
• Risk assessment must be carried out for all suppliers of the material being assessed.
Where there is more than one supplier for a particular material, then each supplier
must be assessed individually.
• A periodic review must be conducted to ensure that the risk assessment and PT or ST
schemes remain valid. Where an assessment has identified a significant risk it must
be appropriately mitigated.
2. Assessment of attributes
3. Routine application of skip testing
4. Change control and remediation
Where to Apply?
• Periodic testing or skip testing should be implemented after performing sufficient risk
evaluation and assessment of product quality during drug product development.
• It should be implemented at commercial level only after gaining sufficient confidence.
Periodic or skip testing approach and stages are represented in the Figure.
https://www.pharmaceuticalsky.com/ Page 3 of 7
https://www.pharmaceuticalsky.com/
Selection Considerations
• PT or ST can be selected and implemented for the testing of regular commercial
batches. For selecting the periodic or skip tests, the following points should be
considered,
1. Whether materials are received from the approved supplier.
2. A documented history of satisfactory results for material supplied and performance
of supplier is available.
3. A documented history of satisfactory performance for the process and product is
available.
4. Compliance with specific regulatory requirements of testing is ensured.
5. Sufficient development data for the specified tests is available.
6. Scientific justification can be provided.
7. To be implemented for tests which are not critical to assess the product quality.
8. Batch to batch retesting to be stored in the event of failure and it should be properly
investigated and closed.
9. An impact assessment of the PT or ST should be undertaken.
https://www.pharmaceuticalsky.com/ Page 4 of 7
https://www.pharmaceuticalsky.com/
10. Does the specification or method provide information about the purity or potency of
the finished product? If not, the specification or method should be reconsidered.
11. Analytical method should predict or prevent the compliance issue.
12. What would be the regulatory impact of eliminating or reducing the test?
Periodic or Skip Testing for in-Process Samples
• Skip testing can be implemented for in-process samples of all categories of finished
drug products such as tablets, capsules, semi-solids and liquids.
• This can be implemented after review of data for 20 to 30 consecutive batches which
have been manufactured without any change in process, formula, equipment or
specification.
• PT/ST can be implemented after approval from the respective regulatory agency.
• After implementation of PT or ST if the process, formula, equipment etc. is changed
then the skip testing procedure should be reevaluated.
• If any OOS/incident is encountered due to process quality and the Root Cause
Analysis indicates in-process testing or a change in the process, specification or test
procedures, then complete testing needs to be performed on few consecutive
batches without any change.
• The internal quality assurance team will be responsible to perform the risk
assessment.
https://www.pharmaceuticalsky.com/ Page 5 of 7
https://www.pharmaceuticalsky.com/
Periodic or Skip Testing for API, Excipients and Packing Materials
• After analyzing 30 to 40 batches, periodic testing or skip testing may be implemented
if data is found satisfactory and without much variation.
• If any OOS/incident is encountered then complete testing of few consecutive batches
is to be performed and the quality assurance team needs to perform the risk
assessment.
https://www.pharmaceuticalsky.com/ Page 6 of 7
https://www.pharmaceuticalsky.com/
Approval
• PT or ST may be implemented for API's, excipients and packaging material after a
favorable review of sufficient batch data and by preparing SOP's which would be
available for an audit by the regulatory agencies.
• For implementation of PT for in-process testing of finished product concurrence from
the agency during the review of an application or after approval is necessary.
• A suitable supplement or variation needs to be submitted to the regulatory agency
for its review if PT is to be implemented for in-process testing of finished product post
approval.
https://www.pharmaceuticalsky.com/ Page 7 of 7
