Foreword

The Operator's Manual

You and others can be killed or seriously injured

if you operate or maintain the machine without
first studying the Operator's Manual. You must
understand and follow the instructions in the
Operator's Manual. If you do not understand
anything, ask your employer or JCB dealer to
explain it.

SERVICE MANUAL Do not operate the machine without an Operator's

Manual, or if there is anything on the machine you
do not understand.

Treat the Operator's Manual as part of the machine.

Keep it clean and in good condition. Replace the
Operator's Manual immediately if it is lost, damaged
or becomes unreadable.

LOADALL (ROUGH TERRAIN

VARIABLE REACH TRUCK) Contents
531-70, 535-95, 541-70
01 - Machine
03 - Attachments, Couplings and Load
Handling
06 - Body and Framework
09 - Operator Station
12 - Heating, Ventilating and Air-
Conditioning (HVAC)
15 - Engine
18 - Fuel and Exhaust System
21 - Cooling System
24 - Brake System
EN - 9813/9050 - ISSUE 1 - 01/2018
25 - Steering System
27 - Driveline
30 - Hydraulic System
This manual contains original instructions, verified by
the manufacturer (or their authorized representative).
33 - Electrical System
72 - Fasteners and Fixings
75 - Consumable Products

Copyright 2017 © JCB SERVICE

78 - After Sales
All rights reserved. No part of this publication may
be reproduced, stored in a retrieval system, or
transmitted in any form or by any other means,
electronic, mechanical, photocopying or otherwise,
without prior permission from JCB SERVICE.

www.jcb.com
 15 - Engine
00 - Engine
00 - General

Drain and Fill Clean

Refer to: PIL 15-21-00. Notice: Clean the engine before you start engine
maintenance. Obey the correct procedures.
Contamination of the fuel system will cause
damage and possible failure of the engine.
Notice: The engine and other components could
be damaged by high pressure washing systems.
Special precautions must be taken if the machine
is to be washed using a high pressure system.
Make sure that the alternator, starter motor and
any other electrical components are shielded
and not directly cleaned by the high pressure
cleaning system. Do not aim the water jet directly
at bearings, oil seals or the engine air induction
system.

Before carrying out any service procedures that

require components to be removed, the engine must
be properly cleaned.

Cleaning must be carried out either in the area of

components to be removed or, in the case of major
work, or work on the fuel system, the whole engine
and surrounding machine must be cleaned.

Stop the engine and allow it to cool for at least one

hour. DO NOT attempt to clean any part of the engine
while it is running.

1. Make sure that the electrical system is isolated.

2. Make sure that all electrical connectors are
correctly coupled. If connectors are open fit the
correct caps or seal with water proof tape.
3. Cover the alternator with a plastic bag to prevent
water ingress.
4. Seal the engine air intake, exhaust and breather
system.
5. Make sure that the oil filler caps and dipstick are
correctly installed.
6. Use a low pressure water jet and soft bristle
brush to soak off caked mud or dirt.
7. Apply an approved cleaning and degreasing
agent with a brush. Obey the manufacturers
instructions.
8. Use a pressure washer to remove the soft dirt
and oil. Important: DO NOT aim the water jet
directly at oil seals or electrical connectors and
electronic components such as ECU (Electronic
Control Unit)'s, alternator or fuel injectors. DO
NOT place the jet nozzle closer than the specified
distance to any part of the engine or exhaust
system.
Length/Dimension/Distance: 600mm

15 - 27 9813/9050-1 15 - 27
 15 - Engine
00 - Engine
00 - General

9. When the pressure washing is complete move Check (Condition)

the machine away from the wash area, or
alternatively, clean away the material washed
from the machine. Start the engine and check for:

10. Before working on specific areas of the engine • Excessive smoke

use a compressed air jet to dry off any moisture. • Excessive vibration
When the area is dry use a soft clean brush to • Excessive noise
remove any sand or grit particles that remain. • Overheating
• Performance
11. When removing components be aware of any • Unusual smells.
dirt or debris that may be exposed. Cover any
open ports and clean away the deposits before
proceeding.

Additional cleaning must be carried out prior to

working on the high pressure fuel system. Refer to:
PIL 18-00-00.

15 - 28 9813/9050-1 15 - 28
 15 - Engine
00 - Engine
00 - General

Check (Leaks) Check (Pressure)

Special Tools
Before you start the machine, do a check for oil leaks: Description Part No. Qty.
Pressure Gauge (0-70 892/00346 1
1. Make the machine safe.
Bar)
2. Get access to the engine compartment (if
applicable) This test is used to diagnose suspected poor
compression in one or more of the engine cylinders.
3. Check the engine and the area below for oil Use ServiceMaster to control the test.
leaks.
4. Close the engine cover (if applicable).
Engine Oil Pressure

5. If necessary, contact your JCB dealer. Use the following procedures to measure the engine
oil pressure. Several factors can influence the engine
oil pressure, the following conditions are assumed:

• The correct engine oil has been used. Refer to:

PIL 15-21-00.
• The engine oil level is correct. Refer to: PIL
75-03-03.
1. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
2. Get access to the engine.
3. Disconnect the electrical connector to the oil
pressure switch, remove the switch from the oil
cooler housing.
4. Install a suitable adaptor into the vacant pressure
switch port (M10 x 1.5mm thread) and a pressure
test gauge. Make sure that the gauge has a
sealing washer as shown.
Special Tool: Pressure Gauge (0-70 Bar) (Qty.: 1)

15 - 29 9813/9050-1 15 - 29
 15 - Engine
00 - Engine
00 - General

Figure 133. • Low oil level - typically evident as a loss of

pressure when operating on uneven ground or
on a gradient.
• Blocked oil filter - a blocked filter will show as a
gradual loss of pressure.
• Blocked suction strainer (pick-up pipe) -
typically evident as low pressure on start up,
A if the blockage frees itself in the sump, the
pressure will pick up to normal.
• Coolant in the oil - coolant in the lubricating oil
will show as a milky discolouration of the oil and
an increase in oil level. Check for damaged core
plugs, lubricating oil cooler, cylinder head and/
or gasket.
• Fuel in the oil - fuel in the oil will result in thin'
black lubricating oil, the oil will also have a
diesel fuel smell. Check the fuel injection pump
(FIP) shaft seal, piston ring wear, lift pump
diaphragm damage or injector leakage if fuel is
B evident in the oil.
• Damaged oil pump - oil pressure will be high at
low oil temperature but fall when oil becomes
hotter.

A Oil pressure switch

B Sealing washer
5. Start the engine and allow a few seconds to
gain oil pressure, increase the engine revs to
the rated speed. Record the pressure gauge
reading. Check that the pressure is within the
specified tolerance.
Refer to: PIL 15-00-00.
6. Remove the pressure gauge and install the
pressure switch.

High Lubrication Oil Pressure

High oil pressure will be evident when starting in cold
conditions. Typically the pressure will be 1 to 2 bar
and higher in cold operation, the pressure should
drop when the engine reaches normal operating
temperature.

If the pressure remains high when operating

temperature is achieved, check the oil level, if this is
correct, suspect the oil pressure relief valve is at fault.

Low Lubrication Oil Pressure

Several factors can be the cause of low lubricating
oil pressure:

15 - 30 9813/9050-1 15 - 30
 15 - Engine
00 - Engine
00 - General

Remove and Install Figure 134.

Special Tools
Description Part No. Qty. Q P
Fuel Injector equipment 320/B9321 1 B
Cap Kit (430 Engine)
Lifting Brackets (430 320/B9421 1 M
Engine)
Engine Lifting Spreader 892/01382 1
Bar
J G
Lifting Equipment
You can be injured if you use incorrect or faulty lifting
equipment. You must identify the weight of the item to
be lifted then choose lifting equipment that is strong
enough and suitable for the job. Make sure that lifting
equipment is in good condition and complies with all H
local regulations.
N
The lifting equipment used must be an approved
type and capable of lifting the engine safely. The
recommended lifting equipment is shown. Use a A
A
spreader bar when lifting the engine. Never attempt
to manually lift heavy components on your own.
Always use lifting equipment, or obtain the help of
an assistant. Inspect the lifting brackets for signs Figure 135.
of damage. The brackets must be correctly torqued
to the crankcase. Make sure the lifting equipment F F
does not damage any of the engine dressing and the R
rocker cover.

Component Identification
The following component identification is for a typical
engine installation. There will be some component
differences depending on the machine variant.
Before attempting to remove the engine ensure that
all the necessary components have either been
removed, or safely disconnected from the engine. D

E
A
A

15 - 31 9813/9050-1 15 - 31
 15 - Engine
00 - Engine
00 - General

Figure 136. 4. Get access to the engine.

Remove
S 1. Disconnect and remove the battery.
2. Drain the engine oil.
Refer to: PIL 15-21-00.
K
3. Drain the engine coolant.
Refer to: PIL 21-00-00.
C
4. Remove the cooling pack.
5. Disconnect the air inlet hose.
L 6. Disconnect the turbocharger outlet hose.
7. Disconnect the charge air hose.
8. Disconnect the exhaust system.
9. Label the cab heater hoses at the engine
block connectors. Release the hose clips and
disconnect the hoses.
10. Disconnect the top coolant hose.
11. Disconnect the bottom coolant hose.
12. Disconnect the wiring connections from the
A Engine mounting bolts starter motor.
B Front lifting bracket - front Refer to: PIL 15-75-00.
C Lifting bracket fixing bolts
D Fuel pipe - return to tank 13. Disconnect the wiring connections from the
E Fuel pipe - feed from lift pump alternator.
F Electrical connector - ECM (Engine Control
Refer to: PIL 15-72-00.
Module)
G Electrical connections - alternator 14. Disconnect the fuel supply and return pipes.
H Hose connection - cab heater Plug all the open ports and hoses to prevent
J Electrical connections - starter motor contamination.
K Rear lifting bracket
L Gearbox/hydraulic pump to engine mounting Special Tool: Fuel Injector equipment Cap Kit
bolts (430 Engine) (Qty.: 1)
M Top coolant hose
15. Disconnect the electrical harness at the ECM
N Bottom coolant hose
machine side connector. Important: Do not touch
P Air inlet hose
the connector pins on the ECM or harness
Q Turbocharger outlet hose
connectors. Cover the connectors to prevent
R Charge air inlet hose
contamination.
S Exhaust pipe
16. Make sure that all relevant harnesses and hoses
Before Removal are unclipped from the engine and tied out of the
way.
1. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before 17. If necessary, drain the hydraulic tank. Disconnect
you start the service work. and plug the hydraulic suction and delivery lines
at the transmission pump and gear pump. Label
2. Position the machine on firm level ground. Make the hoses to aid installation.
the machine safe.
18. Remove the gearbox/hydraulic pump to engine
Refer to: PIL 01-03.
retaining bolts and pull the gearbox/hydraulic
3. Discharge the hydraulic pressure. pump clear of the engine.

15 - 32 9813/9050-1 15 - 32
 15 - Engine
00 - Engine
00 - General

18.1. Make sure that the torque converter stays Figure 137.
mounted on the gearbox shaft.
19. Attach slings to the engine lifting eyes.
Special Tool: Lifting Brackets (430 Engine) (Qty.: T
1)
Special Tool: Engine Lifting Spreader Bar (Qty.:
1)
20. Take the weight of the engine on the hoist and
remove the engine mounting bolts.
21. Raise the engine and lift it clear of the machine.
22. Lower the engine into a suitable stand that is
capable of supporting the weight of the engine.
U

A
A

A Lifting brackets
T Lifting equipment
U Spreader bar

Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
step.
2. It is vitally important that the torque converter
is installed at the gearbox and engine flywheel
correctly. Failure to locate the torque converter
correctly will result in damage to the gearbox oil
pump on engine start up.

15 - 33 9813/9050-1 15 - 33
 15 - Engine
00 - Engine
00 - General

3. Fill the cooling system.

Refer to: PIL 21-00-00.
3.1. When you fill the cooling system make
sure you use the correct water/antifreeze
mixture. A 50% mixture should be
maintained even if frost protection is not
required.
Refer to: PIL 75-09-03.
4. Fill and check the hydraulic fluid level.
5. Fill and check the engine oil level. Make sure the
correct oil is used.
Refer to: PIL 75-03-03.
6. Check the hydraulic, fuel and cooling systems for
leaks.
7. Check the operation of all drive and hydraulic
services.

15 - 34 9813/9050-1 15 - 34
 15 - Engine
00 - Engine
00 - General

Store and Recommission

If an engine is to be placed into storage, all external

Engines should be stored in the original shipping signs of surface coating damage or corrosion should
packaging. Damaged or disturbed packaging should be cleaned and re-coated. Electrical connectors and
be made weatherproof immediately. components should be coated with a protective
spray.
If an engine is shipped with oil, it should be stored in
the correct (upright) position. Capping Engine Openings
If an engine is shipped dry of oil, after 6 months it
All openings on the engine must be suitably capped
should be filled with oil to the correct level and re-
to prevent ingress of water and contamination by
inhibited, refer to hot test description.
foreign particles.
All floor stock engines should be stored under cover
in dry conditions and not subjected to extreme
variations in temperature or humidity.

15 - 35 9813/9050-1 15 - 35
 15 - Engine
00 - Engine
00 - General

Figure 138.

A ECM (Engine Control Module) machine harness B Machine harness interconnect connector cap
connector cap
C Fuel pipe – return to tank cap D Fuel pipe – feed from lift pump cap
E Coolant circuit bleed pipe cap F Air intake cap

15 - 36 9813/9050-1 15 - 36
 15 - Engine
00 - Engine
00 - General

Figure 139.

G Turbocharger intake cap H Coolant top hose cap

J Turbocharger compressor outlet cap K Coolant bottom hose cap
L Cab heater feed and return spigots M Heavy duty PTO (Power Take-Off)

15 - 37 9813/9050-1 15 - 37
 15 - Engine
00 - Engine
00 - General

Figure 140. 2.9. Place in storage, under cover on level

ground or shelving.
2.10. Record details of work as required.
2.11. Do not expose to extremes of temperature
or humidity.
Notice: Do not operate the starter motor for more
than 20s at one time. Let the starter motor cool for
at least 2min.

Table 59. Oil Pressure Switch Set Points

Oil pressure switch >0.6bar (8.7psi)
N closed
Oil pressure switch open <0.6bar (8.7psi)

OEM Commissioning Check on Engine

Installation After More Than 12 Months
N Turbocharger exhaust outlet (tape over)
1. Flush the coolant system with proprietary
12 Month Revalidation Procedure flushing solution.

1. Pre-inspection: 2. Refill the coolant system with 50/50 mix of long

life antifreeze mixture.
1.1. Inspect packaging for signs of damage.
3. Hot test engine according to the hot test profile.
1.2. Inspect the caps for signs of damage. Refer to Table 60.
1.3. Inspect openings for signs of water or dirt 4. Drain engine oil and replace engine oil filter.
ingress.
1.4. Inspect the engine for signs of external 5. Refill with the correct oil and inhibit the cooling
corrosion. system using the correct product.

1.5. Inspect the engine for signs of fluid leaks. 6. Record details of work as required.

2. From storage: Hot Test Description

2.1. Remove the air intake caps. WARNING When using cleaning agents, solvents
or other chemicals, you must adhere to
2.2. Make sure the engine oil level is correct. the manufacturer's instructions and safety
2.3. Using a suitable power supply at the correct precautions.
voltage, crank the engine over for the
specified time period. All engines despatched from JCB will have been
Duration: 20s subjected to a hot test (checking items such as oil
pressure, engines speeds, torque values etc.) and
2.4. During cranking, check that the oil pressure therefore the interior surfaces will have been coated
switch opens using a multimeter. The switch with engine oil.
is closed when there is no or low oil
pressure and opens when oil pressure All coolant galleries are coated with CRODAFLUID
reaches a set point. After three separate PA75 corrosion inhibitor.
cranking periods, If the oil pressure switch
does not open (indicating no, or low oil Stored engines will require re-inhibiting every 12
pressure), contact your JCB engine dealer. months, this will include hot testing the engine using
2.5. Recap all engine openings. a dynamometer. The hot test profile is:

2.6. Coat any exposed bare metal with a Table 60. Hot Test Profile
suitable product.
Stage Mode Speed Torque Time
2.7. Electrical connectors and components (rpm) (Nm) (secs)
should be coated with a protective spray if 1 Speed/ 830 0 50
exposed. Torque
2.8. Cover in weatherproof packaging. 2 Speed/ 1300 50 60
Torque

15 - 38 9813/9050-1 15 - 38
 15 - Engine
06 - Cylinder Head
00 - General

Component Identification
Figure 142.

A Cylinder head bolts

B Cylinder head
C Cylinder head gasket

15 - 47 9813/9050-1 15 - 47
 15 - Engine
06 - Cylinder Head
00 - General

Remove and Install

Special Tools 9. Remove the fuel injector cover.

Description Part No. Qty. Refer to: PIL 18-18-04.
Torque Wrench 993/70111 1
(10-100Nm) 10. Remove the high pressure fuel pipes.
Refer to: PIL 18-96-03.
Consumables
Description Part No. Size 11. Remove the injector leak-off, leak-off pipe to fuel
Cleaner/Degreaser 4104/1557 0.4L filter, and return to tank low pressure fuel pipes.
- General purpose Refer to: PIL 18-96-06.
solvent based parts
cleaner 12. Remove the fuel injectors.
Refer to: PIL 18-18-03.
Before Removal
13. Remove the fuel rail.
This procedure requires service parts. Make sure Refer to: PIL 18-18-12.
you have obtained the correct parts before you start.
Refer to the Parts Catalogue. 14. Remove the EGR (Exhaust Gas Recirculation)
system.
1. Make the machine safe.
Refer to: PIL 18-27-00.
Refer to: PIL 01-03.
15. Remove the exhaust manifold pressure sensor
2. Make sure that the engine is safe to work on. If assembly.
the engine has been running, let it cool before
you start the service work. Refer to: PIL 15-84-16.

3. Get access to the engine. 16. Remove the exhaust manifold and turbocharger
assembly.
4. Drain the coolant. Refer to: PIL 18-24-04.
Refer to: PIL 21-00-00.
17. Remove the glow plugs.
5. Remove the engine wiring harness. Refer to: PIL 15-80-00.
6. Remove the ECM (Engine Control Module). 18. Disconnect the charge air inlet hose.
Refer to: PIL 33-45-06.
19. Remove the rocker cover.
7. Remove the thermostat. Refer to: PIL 15-42-06.
Refer to: PIL 21-12-00.
20. Remove the rocker assembly.
8. Disconnect the CCV (Crankcase Ventilation) Refer to: PIL 15-42-00.
pipes.
Refer to: PIL 15-28-00.

15 - 48 9813/9050-1 15 - 48
 15 - Engine
06 - Cylinder Head
00 - General

Figure 143.

12
12

13 X

11

10 6 2 3 7

9 5 1 4 8

0° +90 °

1-10 Cylinder head fixing bolts (x10) 11 Cylinder head

12 Location dowels (x2) 13 Cylinder head gasket
X Cylinder head gasket identification holes Y Matchmarks

21. Remove the push rods. Make a note of the 3. Using a suitable cleaning agent, carefully remove
order to make sure that they are installed in their all traces of the head gasket material from the
original positions. cylinder head and crankcase mating faces.
Consumable: Cleaner/Degreaser - General
Remove purpose solvent based parts cleaner
1. Progressively remove the cylinder head bolts in 4. Check the cylinder head and crankcase mating
reverse order, starting at bolt 10. The bolts MUST faces for signs of damage and distortion.
NOT be re-used. Discard the bolts.
Refer to: PIL 15-06-00.
2. Carefully lift the cylinder head from the
crankcase. If necessary use a soft face hammer. Before Install
DO NOT use a lever to separate the cylinder
head from the crankcase. Discard the head 1. Obtain the correct new cylinder head bolts. The
gasket. original bolts MUST NOT be re-used.

15 - 49 9813/9050-1 15 - 49
 15 - Engine
06 - Cylinder Head
00 - General

2. Obtain the correct replacement head gasket.

Note the number of cylinder head gasket
identification holes.
3. Make sure that all items are clean and free from
damage and corrosion.

Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that the location dowels are correctly
installed into the crankcase. Use a dowel punch
to install the dowels as required.
3. Position a new head gasket on to the crankcase
mating face. Make sure that the gasket is
installed the correct way around and correctly
located over the dowels.
4. Lower the cylinder head on to the crankcase.
Make sure that the cylinder head is correctly
located on the dowels. Install new cylinder head
bolts. Tighten the bolts in three stages, use the
torque and angle method.
Refer to: PIL 72-00-00.
4.1. Tighten the bolts, starting with the middle
pair and working outwards (in sequence
1-10) to the 1st stage pre-torque.
Special Tool: Torque Wrench (10-100Nm)
(Qty.: 1)
4.2. Tighten the bolts, starting with the middle
pair and working outwards (in sequence 1-
10) to the 2nd stage pre-torque.
4.3. Repeat the 2nd stage pre-torque. Refer to
step 4.2.
4.4. Use the angle gauge to angle tighten the
bolts, starting with the middle pair and
working outwards (in sequence 1-10) to
the final stage torque. As a visual check,
matchmark the bolts to the cylinder head
before you start. When the bolts have
been angle tightened, the matchmarks will
appear as shown at Y. Refer to Figure 143.

Table 63. Torque Table

Item Torque Value
1-10 (1st Stage) 50N·m
1-10 (2nd Stage) 115N·m
1-10 (Final Stage) 90°

15 - 50 9813/9050-1 15 - 50
 15 - Engine
12 - Crankshaft
00 - General

Check (Condition) Blocked or restricted oilways will cause oil

starvation at the big end bearings.
1. Measure the crankshaft journal diameters to 4. Check that the piston cooling saddle jets are
confirm they are within service limits. clear. If the saddle jets cannot be cleared, replace
the saddle jets.
Refer to: PIL 15-12-00.
Figure 149.
Figure 147.
B

A Crankcase
B Crankshaft
C Crankshaft position sensor target wheel
2. Check the main bearing surfaces for damage and
excessive wear.
Figure 148.

E Saddle jets

D Main bearing shells

3. Check that the oil-way cross drillings in the
crankshaft are clear and free from debris.

15 - 61 9813/9050-1 15 - 61
 15 - Engine
12 - Crankshaft
00 - General

Remove and Install

Special Tools Refer to: PIL 15-45-09.

Description Part No. Qty.
12. Remove the bolts (x2) and disconnect the
Template for Sealant 320/02333 1 turbocharger oil drain pipe.
Bedplate to Crankcase
(430 Engine) 13. Remove the oil sump.
Crankshaft Turning Tool 320/A3170 1 Refer to: PIL 15-45-00.
(Major Repair) (430
Engine) 14. It is not necessary to remove the cylinder head
Torque Wrench 993/70111 1 assembly to remove the crankshaft. If however
(10-100Nm) the cylinder head needs to be removed for other
reasons (for piston and connecting rod removal
Consumables for example) remove it now.
Description Part No. Size Refer to: PIL 15-06-00.
Cleaner/Degreaser 4104/1557 0.4L
- General purpose 15. Remove the starter motor.
solvent based parts Refer to: PIL 15-75-00.
cleaner
16. Remove the flywheel.
CAUTION This component is heavy. It must only
Refer to: PIL 15-54-00.
be removed or handled using a suitable lifting
method and device. 17. Remove the rear crankshaft oil seal.
Refer to: PIL 15-12-09.
Before Removal
18. Remove the flywheel housing.
1. This procedure requires service parts. Make Refer to: PIL 15-54-03.
sure you have obtained the correct service parts
before you start, refer to the Parts Catalogue. 19. Remove the oil pump.
2. Make sure that the engine is safe to work on. If Refer to: PIL 15-60-00.
the engine has been running, let it cool before
you start the service work. 20. Remove the bolt securing the fuel hose to the
bedplate.
3. Drain the engine oil.
Figure 150.
Refer to: PIL 15-21-00.
4. Remove the engine.
Refer to: PIL 15-00-00.
5. Remove the fuel filter.
Refer to: PIL 18-09-03.
6. Remove the drive belt.
Refer to: PIL 15-18-03. E

7. Remove the crankshaft pulley.

Refer to: PIL 15-12-12.
8. Remove the front crankshaft oil seal.
E Fuel pipe retaining bolt
Refer to: PIL 15-12-06.
21. Remove the main bearing caps.
9. Position the engine upside down in a suitable jig
or fixture, supported at the front of the crankcase. Refer to: PIL 15-12-03.
10. Remove the dipstick. 22. Set the engine to TDC (Top Dead Centre).
11. Remove the dipstick tube.

15 - 62 9813/9050-1 15 - 62
 15 - Engine
12 - Crankshaft
00 - General

Special Tool: Crankshaft Turning Tool (Major Remove

Repair) (430 Engine) (Qty.: 1)
1. Remove the bedplate peripheral bolts.

Figure 151.

O
O
O

9 5 1 4 8

10 6 2 3 7

O
O O
O
P

N
O

1-10 Main bearing bolts (x10) N Bedplate

O Bedplate peripheral bolts (x12) P O-ring

2. Progressively remove the main bearing bolts in Figure 152.

reverse order starting at bolt 10. The bolts MUST R
NOT be re-used. Discard the bolts. N
3. Install the four temporary lifting bolts. Carefully
separate the bedplate from the crankcase. Use
suitable lifting equipment (if the bedplate is lifted
manually, two people will be required). DO NOT
use a lever to separate the bedplate. R

N Bedplate
R Lifting bolts (obtain locally)
4. Remove the bedplate.

15 - 63 9813/9050-1 15 - 63
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING

NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
 15 - Engine
12 - Crankshaft
00 - General

5. Use suitable lifting equipment to carefully lift the Figure 154.

crankshaft from the crankcase (if the crankshaft
is lifted manually, two people will be required).
6. Remove the thrust washers between the
crankshaft and crankcase rear main bearing.
Figure 153.
A
B

A Thrust washers
B Crankshaft D Main bearing shells
C Rear main bearing
9. It is recommended that the bearing shells are
7. Put labels on the thrust washers to make sure replaced. If however they are to be used again,
that they are installed in the correct positions put labels on the shells to make sure that they
during assembly. are installed in their original positions during
assembly.
8. Carefully lift out the bearing shells.
10. Inspect the crankshaft and main bearings for
damage and excessive wear.
Refer to: PIL 15-12-00.

Before Installation
1. Clean off all traces of the old sealant compound
from the crankcase and bedplate mating faces.
2. Use a suitable degreasing agent to carefully
clean the main bearing saddles in the bedplate
and crankcase. Take care not to block the oil
ways or the piston cooling jets.
Consumable: Cleaner/Degreaser - General
purpose solvent based parts cleaner

Important: Cleanliness is of the utmost importance.

Blocked oil-ways or oil jets will cause engine failure.
Before you install the crankshaft make sure that ALL
oil-ways and jets are clear and free from debris.

Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.

15 - 64 9813/9050-1 15 - 64
 15 - Engine
12 - Crankshaft
00 - General

2. Make sure that all items are clean and free from 4. Use suitable lifting equipment (if the crankshaft
damage and corrosion. is lifted manually, two people will be required), to
carefully lower the crankshaft into the crankcase.
3. Install the upper bearing shells as follows: DO NOT rotate the crankshaft, the bearing shells
can become dislodged. Make sure that the
Figure 155. connecting rods are located onto the crankshaft
journals.
G
4.1. Make sure that the connecting rods are
located onto the crankshaft journals.
4.2. Make sure that the crankshaft is installed
so that the engine timing is correct. The
single mark on the crankshaft drive gear
must locate between the two marks on the
camshaft drive gear.
Figure 156.
J

L
K

D M

Y J Camshaft drive gear timing marks

K Crankshaft drive gear timing mark
L Camshaft drive gear
M Crankshaft drive gear
D Main bearing shells
G Bearing location tab 5. Install the thrust washers as follows:
Y Oil-way holes
3.1. Use a suitable degreasing agent to make
sure that the surfaces of the upper bearing
shells are clean.
Consumable: Cleaner/Degreaser - General
purpose solvent based parts cleaner
3.2. Assemble the bearing shells into the
crankcase bearing saddles. Make sure that
the location tab engages into the slot as
shown.
3.3. Make sure that the oil-way holes in the
bearing saddles align with the holes in the
bearing shell. If the holes are even partially
misaligned the piston cooling oil jet will be
restricted, causing the engine to fail.
3.4. Lubricate the upper bearing shells with
clean engine oil.

15 - 65 9813/9050-1 15 - 65
 15 - Engine
12 - Crankshaft
00 - General

Figure 157. 5.2. Make sure that they are installed in the
correct positions, with the two oil slots
A facing outwards from the bearing saddle.
5.3. If necessary, push the crankshaft forward
and then backwards to obtain clearance to
install the thrust washers.
5.4. DO NOT rotate the crankshaft, the bearing
shells can become dislodged.
H 6. Check that the crankshaft end float is within
service limits.
Refer to: PIL 15-12-00.
7. Install the four lifting bolts to the bedplate as
shown.

A 8. Lubricate the lower bearing shells with clean

engine oil. If the bearings have been removed,
make sure that the location tab engages in the
slot as shown.
Consumable: Cleaner/Degreaser - General
purpose solvent based parts cleaner
9. The sealant template is used on the crankcase,
NOT the bedplate.
Special Tool: Template for Sealant Bedplate to
Crankcase (430 Engine) (Qty.: 1)
B
C 10. Locate the location tabs on the template using
a location dowel and a fixing bolt. Use the
A Thrust washer templates as a guide apply a bead of sealant
B Crankshaft around the crankcase/bedplate mating face as
C Rear main bearing shown to the dimension specified.
H Oil slot - thrust washers Length/Dimension/Distance: 1.5mm
5.1. Slide the thrust washers between the
crankshaft and the crankcase rear main
bearing.

15 - 66 9813/9050-1 15 - 66