AR252 Humidity and temperature transducer
TECHNICAL DATA (the detailed data can be found in the user’s instruction)
Sensor SHT31 made by Sensirion, an ABS cover (slot width 1mm)
and a stainless steel wire mesh (slot width 0.15mm)
Measurement range 0÷100 %RH, -30÷80 °C
Measurement humidity ±2 %RH in the entire measurement range
acurancy
temperature ±0,3 °C in the entire measurement range
Hysteresis and stability ±0,8 %RH, long-term stability < 0,25 %RH / year
Okres pomiarowy 1s
AR252 Response time (63%) 8s (for air flow > 3,6km/h)
standard
Display (optional) LCD, 4 digits 10 mm
Outputs current (IH, IT) 2 x 4÷20 mA (2P), load RO< (Uzas-12) / 22 mA
voltage (UH, UT) 2 x 0÷10 V (3P), load IO<4,5 mA (Rw > 2,5 kΩ)
digital (not separated) RS485, MODBUS-RTU (slave)
Power supply for the 4÷20 mA 12÷36 Vdc (2-wire, 2P) supply from the current loop
AR252/L150
probe on for the 0÷10 V 18÷30 Vdc, current consumption: ~7mA (with and without an LCD)
a stainless steel
pipe version with RS485 9÷28 Vac or 9÷36 Vdc, current cons.: ~5mA (with and without an LCD)
PROGRAMMING Operating conditions air and neutral gases (do not pour water on the measurement probe)
standard -30÷80 °C, <100 %RH (no condensation)
AR252/LCD AR956 with an LCD display -20÷70 °C, <100 %RH (no condensation)
with a display COPYING
INSTALLATION DATA
a high class digital relative humidity and temperature sensor with a protective
n
filter (ABS material as a standard, slot width 1 mm, and steel wire mesh with Dimensions 58x94x35 mm
mesh size of 0.15 mm); Material polycarbonate
a probe integrated with the enclosure, external or on a stainless steel pipe
n
94 58
a current output, 4÷20 mA (2-wire, with power supply from the current loop); a
n 80
voltage output 0÷10 V (3-wire), or an RS485 interface 64
calculation of the dew/frost point [°C], relative humidity [g/m3] (calculations for
n 35
atmospheric pressure of 1,013 hPa) with possibility to link the calculated values to
Φ9
an analog output;
temperature compensation of humidity measurement, high measurement
n 58
45
stability Probe
Probe integrated with
programmable processing ranges for humidity and temperature
n integrated the enclosure
an LCD display with a keypad (option) that enables configuration of parameters
n with the enclosure channel design
45 AR252 AR252/T
configuration of parameters with the keypad, through the RS485 or PRG port
n
(programmer AR956 or AR955) and free ARsoft-CFG software that enables quick
setting and copying of all configuration parameters TERMINAL
protection rating IP65 provided by the enclosure which improves reliability of
n
AR252/I
operation thanks to high resistance to penetration of water and dust and surface ~1500
IT
condensation of steam inside of the device; an IP40 probe
100 lub 200
1 +
mA
_ R
power supply
available accessory filter with a metal wire mesh to protect the sensor against
o
n 2 IH 12÷36 Vdc
140 lub 240
mA _
dust V+
+ _ Ro
62 3 +
Contents of the package: Available accessories: NOTE:
- a transducer - a metal wire mesh filter (mesh size approx. 25 μm) The current loop IH must ALWAYS be closed
15
- a user instruction - an AR956 (or AR955) programmer even when it is not in use
External
- a warranty card - a RS485/USB converter Probe
probe AR252/U
Ordering method wit a wire on a stainless UT +
steel pipe 1
AR252 / o
/o
/o
/o AR252/2 AR252/L150 Rw V
GND _
AR252/L250 2
Probe intsalation method Code UH +
radial (standard) - 3
Rw V
Display Code back (to pipe, channel) T ~1500 4 GND _
power supply
LCD * LCD
without a display - Measurement probe type Code
5 GND 18÷30 Vdc
_
integrated with the enclosure (standard) - 6 V+ +
Output Code external with a 1,5m wire* 2
output 4÷20 mA I external in an enclosure with a 1,5m wire* 3
58 AR252/R485
output 0÷10 V U on a stainless steel pipe, 140 mm long* L150
interface RS485 RS485 on a stainless steel pipe, 240 mm long* L250
1 power supply
Order example: * options charged separately 9÷36 Vdc
2 9÷28 Vac
Note: for the standard design, only the output type must be stated e.g.: External probe
AR252 / I 45 JP1
in an enclosure 3 + RS
AR252 w/o display, outputs 4÷20mA, radially mounted probe and integrated with the enclosure with a wire
AR252 / LCD / U / L150 / T AR252/3 4 - RS
AR252 with a display, analog output 0÷10V, probe on a stainless steel pipe, 140mm long, installed in the back 94
of the enclosure (for channel installations) Version 3.0.0 2016-09-30
www.apar.pl APAR - Sales Office, 05-090 Raszyn, ul. Gałczyńskiego 6, tel. +48 22 101-27-31, +48 22 853-48-56 • email: [email protected]
CALIBRATION CERTIFICATE - DIGITAL HUMIDITY AND TEMPERATURE SENSORS
MADE BY SENSIRION
