Arba Minch Polytechnic Satellite Institute
(Basic Shielded Metal Arc Welding)
Approved by: ____________________________ Sign ____________ Date ____________
Knowledge Test Exam on Basic SMAW for GMFA Level II (RPL) Time allowed 30minutes
Prepared by: - [email protected] 2014/07
Arba Minch Polytechnic Satellite Institute
Name _____________________ ID. NO. _________Dept’_______
Part I. Say True or False (1 point each).
_______ 1.Welding is not the technique of joining together metals.
_______ 2.Joints are compact and do not require additional plates in case of riveted joints.
_______ 3.The types of joints are three.
_______ 4.The best possible material for welders clothing is fanned leather.
_______ 5.A weave bead is type of weld bead which is made by side-to-side movement of the
electrode.
Part II. Choose the Correct Answer (2 point each).
_______ 1.Shielded metal arc welding is a process of using a coated rod called _______
A. An arc B. Shield C. Fusion D. None of the above
_______ 2.Welding is ________________
A. Non-hazardous B. Dangerous C. Hazardous D. All
_______3.Common fusion welding processes
A. Electric arc B. Gas C. Electron beam D. All
_______ 4.________ is a single movement of the electrode along the weld joint.
A. Stringer bead B. A weave bead C. Weld pass D. All
_______ 5.Arc welding machines are classified as;
A. Neither AC nor DC B. Either AC or DC C. All D. None
Part III Fill in the Blank Space (1 point each).
1. The division of joints are __________________ and ___________________
2. The basic types of welding __________________ and __________________
3. The principal types of joints mostly used in welding processes
A. _________________________
B. _________________________
C. _________________________
D. _________________________
E. _________________________
Arba Minch Polytechnic Satellite Institute
Job Sheet
Job Title: To make Butt joint, T- joint, Corner joint, Lap joint and Edge joint.
Unit: Shaping metals Welding.
Reading: General Mechanics (page 355 to 390).
Objectives: The trainee’s will make Butt joint, T- joint, Corner joint, Lap joint and
Edge joint by using the AC or DC welding machines.
Laboratory work: Tools, Equipments and Materials
Item No Qty Unit Description Remark
1 1 pcs Welding machines AC or DC
2 1 pcs Hacksaw
3 1 pcs Steel rule
4 10 pcs Flat iron 3x50mm
5 5 pcs Electrode 2.5mm E-6013
6 1 pcs Face shield
7 1 pcs Tong
8 1 pcs Hand glove
Procedure: Make the Butt joint, T- joint, Corner joint, Lap joint and Edge joint as the
drawing given (see the back page).Use mild steel flat bar, cut on the bench table.
After cutting to approximate size, finish shaping by the welding on the AC or DC
welding machines. Check accuracy of the joint angles.
Evaluation: The teacher examination and inspection, using the following criteria.
All steps were completed in the correct sequence/manner
All safety procedures were followed in using hand tools and equipments.
All dimensions (size, shape, joint angles) are accurate and consistent with those
called for in the procedure.
Arba Minch Polytechnic Satellite Institute
Operation Sheet
Title: Operate and use the welding machines.
Purpose: To know the purpose of the welding machines.
Conditions: Give the required equipments and materials the trainee will operate/use the
welding machines at a proper way and better quality.
Tools, Equipments and Materials
Item No Qty Unit Description Remark
1 1 pcs Welding machines AC or DC
2 1 pcs Hacksaw
3 1 pcs Steel rule
4 10 pcs Flat iron 3x50mm
5 5 pcs Electrode 2.5mm E-6013
6 1 pcs Face shield
7 1 pcs Tong
8 1 pcs Hand glove
Procedure:
Prepare machines for welding appropriately.
Prepare materials/work pieces
Adjust the current according to the thickness of the material
Place the work piece on the welding table and start welding.
Precaution: Exercise extreme caution when welding the work piece with the welding
machines.
Quality criteria:
A long flat iron bar was selected for cutting.
Cut the flat iron bar at 50mm long.
Remove rusts, greases and oils from the work piece.
Arba Minch Polytechnic Satellite Institute
Practical Test Exam on Basic SMAW for GMFA Level II (RPL) Time allowed 120ꞌ
Name ___________________________ ID. NO. ___________ Dept’
Arba Minch Polytechnic Satellite Institute
Arba Minch Polytechnic Satellite Institute
