(1/14)

SERVICING SPECIFICATIONS
(1) ENGINE BODY
Item Service Specification Service Limit
Lubricating oil capacity

V2607-CR-E5, 10.2 L
V2607-CR-TE5, 2.69 U.S.gals —
V2607-CR-TIE5 2.24 Imp.gals

11.2 L
V3307-CR-TE5,
2.96 U.S.gals —
V3307-CR-TIE5
2.46 Imp.gals

Cylinder head surface

0.05 mm / 500 mm
Flatness —
0.002 in. / 19.7 in.

Compression pressure
3.20 MPa / 250 min-1 (rpm) 2.20 MPa / 250 min-1 (rpm)
V2607-CR-E5 32.6 kgf/cm2 / 250 min-1 (rpm) 22.4 kgf/cm2 / 250 min-1 (rpm)
464 psi / 250 min-1 (rpm) 319 psi / 250 min-1 (rpm)

V2607-CR-TE5, 3.10 MPa / 250 min-1 (rpm) 2.10 MPa / 250 min-1 (rpm)
V2607-CR-TIE5,
31.6 kgf/cm2 / 250 min-1 (rpm) 21.4 kgf/cm2 / 250 min-1 (rpm)
V3307-CR-TE5,
V3307-CR-TIE5 450 psi / 250 min-1 (rpm) 305 psi / 250 min-1 (rpm)

Top clearance

0.60 to 0.80 mm
—
0.024 to 0.031 in.

© KUBOTA Corporation 2019

KiSC issued 08, 2019 A
 (2/14)

Item Service Specification Service Limit

Valve clearance (When cold)

0.13 to 0.17 mm
—
0.0052 to 0.0066 in.

Valve & valve seat Face angle (A) 0.79 rad

—
(Intake) 45°
Face angle (A) 0.79 rad
—
(Exhaust) 45°
Seat angle (B) 0.79 rad
—
(Intake) 45°
B Seat angle (B) 0.79 rad
—
C (Exhaust) 45°
A
Seat width (C) 3.3 to 3.6 mm
—
(Intake) 0.13 to 0.14 in.
Seat width (C) 3.3 to 3.6 mm
—
(Exhaust) 0.13 to 0.14 in.
Valve stem to valve guide V2607-CR-E5, 0.030 to 0.057 mm
V2607-CR-TE5,
Clearance 0.0012 to 0.0022 in. 0.10 mm
V2607-CR-TIE5
(Intake) 0.0039 in.
V3307-CR-TE5, 0.055 to 0.085 mm
V3307-CR-TIE5 0.0022 to 0.0033 in.

V2607-CR-E5, 0.045 to 0.072 mm

V2607-CR-TE5,
Clearance 0.0018 to 0.0028 in. 0.10 mm
V2607-CR-TIE5
(Exhaust) 0.0039 in.
V3307-CR-TE5, 0.055 to 0.085 mm
V3307-CR-TIE5 0.0022 to 0.0033 in.

V2607-CR-E5, 5.968 to 5.980 mm

V2607-CR-TE5, —
Valve stem O.D. 0.2350 to 0.2354 in.
V2607-CR-TIE5
(Intake)
V3307-CR-TE5, 6.960 to 6.975 mm
—
V3307-CR-TIE5 0.2741 to 0.2746 in.

V2607-CR-E5, 5.953 to 5.965 mm

V2607-CR-TE5, —
Valve stem O.D. 0.2344 to 0.2348 in.
V2607-CR-TIE5
(Exhaust)
V3307-CR-TE5, 6.960 to 6.975 mm
—
V3307-CR-TIE5 0.2741 to 0.2746 in.

V2607-CR-E5, 6.010 to 6.025 mm

V2607-CR-TE5, —
Valve guide I.D. 0.2367 to 0.2372 in.
V2607-CR-TIE5
(Intake)
V3307-CR-TE5, 7.030 to 7.045 mm
—
V3307-CR-TIE5 0.2768 to 0.2773 in.

V2607-CR-E5,
6.010 to 6.025 mm
V2607-CR-TE5, —
Valve guide I.D. 0.2367 to 0.2372 in.
V2607-CR-TIE5
(Exhaust)
V3307-CR-TE5, 7.030 to 7.045 mm
—
V3307-CR-TIE5 0.2768 to 0.2773 in.

KiSC issued 08, 2019 A

 (3/14)

Item Service Specification Service Limit

Valve recessing
0.65 to 0.85 mm (Recessing) 1.2 mm (Recessing)
Intake valve
0.026 to 0.033 in. (Recessing) 0.047 in. (Recessing)

0.65 to 0.85 mm (Recessing) 1.2 mm (Recessing)

Exhaust valve
0.026 to 0.033 in. (Recessing) 0.047 in. (Recessing)

Valve spring V2607-CR-E5, 38.3 to 38.8 mm 37.8 mm

V2607-CR-TE5,
Free length (A) 1.51 to 1.52 in. 1.49 in.
V2607-CR-TIE5
(Intake)
V3307-CR-TE5, 35.1 to 35.6 mm 34.6 mm
V3307-CR-TIE5 1.39 to 1.40 in. 1.36 in.
V2607-CR-E5, 38.3 to 38.8 mm 37.8 mm
V2607-CR-TE5,
Free length (A) 1.51 to 1.52 in. 1.49 in.
V2607-CR-TIE5
(Exhaust)
V3307-CR-TE5, 35.1 to 35.6 mm 34.6 mm
V3307-CR-TIE5 1.39 to 1.40 in. 1.36 in.
B
Tilt (B) 1.0 mm
—
(Intake) 0.039 in.
A
Tilt (B) 1.0 mm
—
(Exhaust) 0.039 in.
V2607-CR-E5, 83.6 N / 30.3 mm
V2607-CR-TE5, 8.52 kgf / 30.3 mm —
Setting load / V2607-CR-TIE5 18.8 lbf / 1.19 in.
Setting length
(Intake) 63.5 N / 31.5 mm
V3307-CR-TE5,
6.48 kgf / 31.5 mm —
V3307-CR-TIE5
14.3 lbf / 1.24 in.
V2607-CR-E5, 83.6 N / 30.3 mm
V2607-CR-TE5, 8.52 kgf / 30.3 mm —
Setting load / V2607-CR-TIE5 18.8 lbf / 1.19 in.
Setting length
(Exhaust) 63.5 N / 31.5 mm
V3307-CR-TE5,
6.48 kgf / 31.5 mm —
V3307-CR-TIE5
14.3 lbf / 1.24 in.
Valve timing V2607-CR-TE5, 0.21 rad before T.D.C.
—
V2607-CR-TIE5 (12° before T.D.C.)
Open
(Intake valve) V2607-CR-E5, 0.24 rad before T.D.C.
V3307-CR-TE5, —
(14° before T.D.C.)
V3307-CR-TIE5
I.O. T.D.C. E.C. V2607-CR-TE5, 0.77 rad after B.D.C.
—
V2607-CR-TIE5 (44° after B.D.C.)
Close
(Intake valve) V2607-CR-E5, 0.70 rad after B.D.C.
V3307-CR-TE5, —
(40° after B.D.C.)
V3307-CR-TIE5
V2607-CR-TE5, 0.86 rad before B.D.C.
—
V2607-CR-TIE5 (49° before B.D.C.)
Open
(Exhaust valve) V2607-CR-E5, 0.87 rad before B.D.C.
E.O. V3307-CR-TE5, —
(50° before B.D.C.)
I.C.
B.D.C. V3307-CR-TIE5
V2607-CR-TE5, 0.30 rad after T.D.C.
—
V2607-CR-TIE5 (17° after T.D.C.)
Close
(Exhaust valve) V2607-CR-E5, 0.24 rad after T.D.C.
V3307-CR-TE5, —
(14° after T.D.C.)
V3307-CR-TIE5

KiSC issued 08, 2019 A

 (4/14)

Item Service Specification Service Limit

Rocker arm shaft to rocker arm 0.016 to 0.045 mm 0.15 mm
Oil clearance
0.00063 to 0.0017 in. 0.0059 in.

V2607-CR-E5, 13.973 to 13.984 mm

V2607-CR-TE5, —
Rocker arm shaft 0.55012 to 0.55055 in.
V2607-CR-TIE5
O.D.
V3307-CR-TE5, 14.973 to 14.984 mm
—
V3307-CR-TIE5 0.58949 to 0.58992 in.

V2607-CR-E5, 14.000 to 14.018 mm

V2607-CR-TE5, —
0.55119 to 0.55188 in.
Rocker arm I.D. V2607-CR-TIE5

V3307-CR-TE5, 15.000 to 15.018 mm

—
V3307-CR-TIE5 0.59056 to 0.59125 in.
Valve bridge shaft to valve bridge arm V2607-CR-E5, 0.018 to 0.042 mm 0.15 mm
V2607-CR-TE5,
0.00071 to 0.0016 in. 0.0059 in.
Oil clearance V2607-CR-TIE5

V3307-CR-TE5, 0.018 to 0.042 mm 0.15 mm

V3307-CR-TIE5 0.00071 to 0.0016 in. 0.0059 in.

V2607-CR-E5, 8.023 to 8.032 mm

V2607-CR-TE5, —
Valve bridge shaft 0.3159 to 0.3162 in.
V2607-CR-TIE5
O.D.
V3307-CR-TE5, 9.023 to 9.032 mm
—
V3307-CR-TIE5 0.3553 to 0.3555 in.

V2607-CR-E5, 8.050 to 8.065 mm

V2607-CR-TE5, —
Valve bridge arm 0.3170 to 0.3175 in.
V2607-CR-TIE5
I.D.
V3307-CR-TE5, 9.050 to 9.065 mm
—
V3307-CR-TIE5 0.3563 to 0.3568 in.
Push rod

0.25 mm
Alignment —
0.0098 in.

Tappet to tappet guide bore

0.020 to 0.050 mm 0.07 mm
Oil clearance
0.00079 to 0.0019 in. 0.003 in.

9.965 to 9.980 mm
Tappet O.D. (A) —
0.3924 to 0.3929 in.

10.000 to 10.015 mm
(A) (B) Tappet guide bore I.D. (B) —
0.39370 to 0.39429 in.

KiSC issued 08, 2019 A

 (5/14)

Item Service Specification Service Limit

Timing gear
(B)
V2607-CR-E5, 0.0400 to 0.118 mm 0.22 mm
V2607-CR-TE5,
0.00158 to 0.00464 in. 0.0087 in.
V2607-CR-TIE5
Backlash
(Crank gear to
(C)
cam gear) (A)

(A) V3307-CR-TE5, 0.0410 to 0.139 mm 0.22 mm

V3307-CR-TIE5 0.00162 to 0.00547 in. 0.0087 in.

V2607-CR-E5, 0.0400 to 0.159 mm 0.22 mm

V2607-CR-TE5,
V2607-CR-TIE5 0.00158 to 0.00625 in. 0.0087 in.

Backlash
(Cam gear to idle
(B) gear) (B)

V3307-CR-TE5, 0.0410 to 0.145 mm 0.22 mm

V3307-CR-TIE5 0.00162 to 0.00570 in. 0.0087 in.

(C)

(A) V2607-CR-E5, 0.0400 to 0.168 mm 0.22 mm

V2607-CR-TE5,
0.00158 to 0.00661 in. 0.0087 in.
V2607-CR-TIE5
Backlash
(Idle gear to
supply pump
gear) (C)
V3307-CR-TE5, 0.0410 to 0.139 mm 0.22 mm
V3307-CR-TIE5 0.00162 to 0.00547 in. 0.0087 in.

Idle gear
V2607-CR-E5, 0.050 to 0.20 mm 0.90 mm
V2607-CR-TE5,
0.0020 to 0.0078 in. 0.035 in.
V2607-CR-TIE5

Side clearance

V3307-CR-TE5, 0.15 to 0.25 mm 0.90 mm

V3307-CR-TIE5 0.0059 to 0.0098 in. 0.035 in.

KiSC issued 08, 2019 A

 (6/14)

Item Service Specification Service Limit

Idle gear shaft to idle gear bushing V2607-CR-E5, 0.0250 to 0.0960 mm 0.10 mm
V2607-CR-TE5,
0.000985 to 0.00377 in. 0.0039 in.
V2607-CR-TIE5
Oil clearance
V3307-CR-TE5, 0.0250 to 0.106 mm 0.11 mm
V3307-CR-TIE5 0.000985 to 0.00417 in. 0.0043 in.

V2607-CR-E5, 34.959 to 34.975 mm

V2607-CR-TE5, —
1.3764 to 1.3769 in.
Idle gear shaft V2607-CR-TIE5
O.D
V3307-CR-TE5, 46.959 to 46.975 mm
—
V3307-CR-TIE5 1.8488 to 1.8494 in.

V2607-CR-E5, 35.000 to 35.055 mm

V2607-CR-TE5, —
1.3780 to 1.3801 in.
Idle gear bushing V2607-CR-TIE5
I.D.
V3307-CR-TE5, 47.000 to 47.065 mm
—
V3307-CR-TIE5 1.8504 to 1.8529 in.

Camshaft

0.01 mm
Alignment —
0.0004 in.

Camshaft

0.131 to 0.191 mm 0.30 mm

Side clearance
0.00516 to 0.00751 in. 0.012 in.

Cam
32.70 mm 32.20 mm
V2607-CR-E5
1.287 in. 1.268 in.

Height V2607-CR-TE5, 32.60 mm 32.10 mm

(Intake) V2607-CR-TIE5 1.283 in. 1.264 in.

V3307-CR-TE5, 37.50 mm 37.00 mm

V3307-CR-TIE5 1.476 in. 1.457 in.

33.20 mm 32.70 mm
V2607-CR-E5
1.307 in. 1.287 in.

Height V2607-CR-TE5, 33.00 mm 32.50 mm

(Exhaust) V2607-CR-TIE5 1.299 in. 1.280 in.

V3307-CR-TE5, 37.90 mm 37.40 mm

V3307-CR-TIE5 1.492 in. 1.472 in.

KiSC issued 08, 2019 A

 (7/14)

Item Service Specification Service Limit

Camshaft journal to crankcase bore
0.050 to 0.091 mm 0.15 mm
Oil clearance
0.0020 to 0.0035 in. 0.0059 in.

Camshaft journal 1 34.934 to 34.950 mm

—
O.D. 1.3754 to 1.3759 in.

Crankcase 35.000 to 35.025 mm

—
bore 1 I.D. 1.3780 to 1.3789 in.

V2607-CR-E5, 41.934 to 41.950 mm

V2607-CR-TE5, —
1.6510 to 1.6515 in.
V2607-CR-TIE5
Camshaft journal 2
O.D.
V3307-CR-TE5, 43.934 to 43.950 mm
—
V3307-CR-TIE5 1.7297 to 1.7303 in.

V2607-CR-E5, 42.000 to 42.025 mm

V2607-CR-TE5, —
1.6536 to 1.6545 in.
V2607-CR-TIE5
Crankcase
bore 2 I.D.
V3307-CR-TE5, 44.000 to 44.025 mm
—
V3307-CR-TIE5 1.7323 to 1.7332 in.

Piston pin bore

V2607-CR-E5, 26.000 to 26.013 mm 26.05 mm
V2607-CR-TE5,
1.0237 to 1.0241 in. 1.026 in.
V2607-CR-TIE5

Piston pin bore I.D.

V3307-CR-TE5, 28.000 to 28.013 mm 28.05 mm

V3307-CR-TIE5 1.1024 to 1.1028 in. 1.104 in.

Piston pin to small end bushing V2607-CR-E5,

0.014 to 0.034 mm 0.15 mm
V2607-CR-TE5,
0.00056 to 0.0013 in. 0.0059 in.
V2607-CR-TIE5
Oil clearance
V3307-CR-TE5, 0.020 to 0.040 mm 0.15 mm
V3307-CR-TIE5 0.00079 to 0.0015 in. 0.0059 in.

V2607-CR-E5, 26.006 to 26.011 mm

V2607-CR-TE5, —
1.0239 to 1.0240 in.
V2607-CR-TIE5
Piston pin O.D.
V3307-CR-TE5, 28.006 to 28.011 mm
—
V3307-CR-TIE5 1.1026 to 1.1027 in.

V2607-CR-E5, 26.025 to 26.040 mm

V2607-CR-TE5, —
1.0246 to 1.0251 in.
V2607-CR-TIE5
Small end bushing
I.D.
V3307-CR-TE5, 28.031 to 28.046 mm
—
V3307-CR-TIE5 1.1036 to 1.1041 in.

KiSC issued 08, 2019 A

 (8/14)

Item Service Specification Service Limit

Piston ring V2607-CR-E5, 0.20 to 0.35 mm 1.25 mm
V2607-CR-TE5,
0.0079 to 0.013 in. 0.0492 in.
Ring gap V2607-CR-TIE5
(Top ring)
V3307-CR-TE5, 0.25 to 0.40 mm 1.25 mm
V3307-CR-TIE5 0.0099 to 0.015 in. 0.0492 in.

Ring gap 0.30 to 0.45 mm 1.25 mm

(Second ring) 0.012 to 0.017 in. 0.0492 in.

Ring gap 0.25 to 0.45 mm 1.25 mm

(Oil ring) 0.0099 to 0.017 in. 0.0492 in.

Piston ring groove to piston ring

Clearance 0.050 to 0.090 mm 0.15 mm
(Top ring) 0.0020 to 0.0035 in. 0.0059 in.

Clearance 0.090 to 0.12 mm 0.20 mm

(Second ring) 0.0036 to 0.0047 in. 0.0079 in.

Clearance 0.020 to 0.060 mm 0.15 mm

(Oil ring) 0.00079 to 0.0023 in. 0.0059 in.

Connecting rod

0.05 mm
Alignment —
0.002 in.

Crankshaft

0.02 mm
Alignment —
0.0008 in.

Crankshaft journal to crankshaft bear- V2607-CR-E5,

ing 0.030 to 0.070 mm 0.20 mm
V2607-CR-TE5,
0.0012 to 0.0027 in. 0.0079 in.
V2607-CR-TIE5
Oil clearance
V3307-CR-TE5, 0.030 to 0.070 mm 0.20 mm
V3307-CR-TIE5 0.0012 to 0.0027 in. 0.0079 in.

V2607-CR-E5, 72.977 to 72.990 mm

V2607-CR-TE5, —
2.8732 to 2.8736 in.
V2607-CR-TIE5
Crankshaft journal
O.D.
V3307-CR-TE5, 79.977 to 79.990 mm
—
V3307-CR-TIE5 3.1487 to 3.1492 in.

KiSC issued 08, 2019 A

 (9/14)

Item Service Specification Service Limit

Crankpin to crankpin bearing
V2607-CR-E5, 0.017 to 0.048 mm 0.20 mm
V2607-CR-TE5,
0.00067 to 0.0018 in. 0.0079 in.
V2607-CR-TIE5

Oil clearance

V3307-CR-TE5, 0.017 to 0.048 mm 0.20 mm

V3307-CR-TIE5 0.00067 to 0.0018 in. 0.0079 in.

V2607-CR-E5, 46.980 to 46.991 mm

V2607-CR-TE5, —
1.8496 to 1.8500 in.
(A) V2607-CR-TIE5

Crankpin O.D. (A)

V3307-CR-TE5, 49.980 to 49.991 mm

—
V3307-CR-TIE5 1.9678 to 1.9681 in.

Crankshaft

0.15 to 0.35 mm 0.50 mm

Side clearance
0.0059 to 0.013 in. 0.020 in.

Crankshaft V2607-CR-E5, 87.000 to 87.022 mm 87.150 mm

V2607-CR-TE5,
3.4252 to 3.4260 in. 3.4311 in.
V2607-CR-TIE5
Bore I.D.
(Standard size)
V3307-CR-TE5, 94.000 to 94.022 mm 94.150 mm
V3307-CR-TIE5 3.7008 to 3.7016 in. 3.7067 in.

V2607-CR-E5, 87.250 to 87.272 mm 87.400 mm

V2607-CR-TE5,
3.4351 to 3.4359 in. 3.4409 in.
V2607-CR-TIE5
Bore I.D.
(Oversize)
V3307-CR-TE5, 94.500 to 94.522 mm 94.650 mm
V3307-CR-TIE5 3.7205 to 3.7213 in. 3.7264 in.

KiSC issued 08, 2019 A

 (10/14)
(2) LUBRICATING SYSTEM
Item Service Specification Service Limit
Engine oil pressure
50 kPa
Engine oil pressure
All Models — 0.51 kgf/cm2
(At idle speed)
7.3 psi

V2607-CR-E5, 245 to 441 kPa 150 kPa

V2607-CR-TE5, 2.50 to 4.49 kgf/cm2 1.53 kgf/cm2
V2607-CR-TIE5 35.6 to 63.9 psi 21.8 psi
Engine oil pressure
(At rated speed)
196 to 392 kPa 150 kPa
V3307-CR-TE5,
2.00 to 3.99 kgf/cm2 1.53 kgf/cm2
V3307-CR-TIE5
28.5 to 56.8 psi 21.8 psi

Inner rotor to outer rotor (Oil pump)

0.030 to 0.090 mm 0.3 mm

Clearance
0.0012 to 0.0035 in. 0.01 in.

Outer rotor to pump body (Oil pump)

0.100 to 0.184 mm 0.3 mm

Clearance
0.00394 to 0.00724 in. 0.01 in.

Inner rotor to cover (Oil pump)

0.025 to 0.075 mm 0.225 mm

Clearance
0.00099 to 0.0029 in. 0.00886 in.

Relief valve spring

60.0 to 60.5 mm 55.0 mm

Free length (A)
2.37 to 2.38 in. 2.17 in.

(A)

KiSC issued 08, 2019 A

 (11/14)
(3) COOLING SYSTEM
Item Service Specification Service Limit
Fan belt

7.0 to 9.0 mm
(0.28 to 0.35 in.)
Tension —
deflection at 98 N
(10 kgf, 22 lbf) of force

Thermostat V2607-CR-E5, 80.0 to 84.0 °C

V2607-CR-TE5, —
Valve opening 176.0 to 183.2 °F
V2607-CR-TIE5
temperature
(At beginning) 74.5 to 78.5 °C
V3307-CR-TE5,
—
V3307-CR-TIE5 166.1 to 173.3 °F

V2607-CR-E5, 95 °C
V2607-CR-TE5, —
Valve opening 203 °F
V2607-CR-TIE5
temperature
(Opened
completely) V3307-CR-TE5, 90 °C
—
V3307-CR-TIE5 194 °F

Radiator

No water leak at
Water tightness —
specified pressure

Radiator cap

10 seconds or more
for pressure falling
Pressure falling
from 90 to 60 kPa —
time
(from 0.91 to 0.62 kgf/cm2,
from 13 to 8.7 psi)

KiSC issued 08, 2019 A

 (12/14)
(4) ELECTRICAL SYSTEM
Item Service Specification Service Limit
Starter

32.0 mm 31.4 mm
Commutator O.D.
1.26 in. 1.24 in.

Starter

0.50 mm 0.20 mm
Mica under cut
0.020 in. 0.0079 in.

Starter

18.0 mm 11.0 mm
Brush length
0.709 in. 0.433 in.

Starter

Brush holder
resistance
Infinity —
(Brush holder -
Holder support)

Starter

Field coil resistance

Continuity —
(Lead - Brush)

Starter

Field coil resistance

Infinity —
(Brush - Yoke)

KiSC issued 08, 2019 A

 (13/14)

Item Service Specification Service Limit

Starter

Armature coil resistance

(Commutator - Infinity —
Armature coil core)

Starter

Armature coil resistance

(Segment - Continuity —
Segment)

Alternator

Stator resistance Less than 1.0 Ω —

Alternator

Rotor resistance 2.8 to 3.3 Ω —

Alternator

22.7 mm 22.1 mm
Slip ring O.D.
0.894 in. 0.870 in.

KiSC issued 08, 2019 A

 (14/14)

Item Service Specification Service Limit

Alternator

18.5 mm 5.0 mm
Brush length
0.728 in. 0.20 in.

Glow plug

Resistance Approx. 0.95 Ω —

KiSC issued 08, 2019 A

 (1/8)
TIGHTENING TORQUES
(1) Special Tightening Torques
For " * " marked screws, bolts and nuts on under table, apply engine oil to their threads and seats before tightening.
For " ** " marked parts on under table, apply the anti-seize & lubricating compound
(Bostick, NEVER-SEEZ, Pure nickel special grade) to their threads and seats before tightening.
Drain plug Alternator pulley nut Alternator pulley nut

V2607-CR-E5
V3307-CR-TE5
44.1 to 53.9 N·m 58.4 to 78.9 N·m 98.0 to 137 N·m
All Models 4.50 to 5.49 kgf·m V2607-CR-TE5 5.96 to 8.04 kgf·m 10.0 to 13.9 kgf·m
32.6 to 39.7 lbf·ft 43.1 to 58.1 lbf·ft 72.3 to 101 lbf·ft
V3307-CR-TIE5
V2607-CR-TIE5

Crankcase 2 mounting screw * Crankcase 2 mounting screw * Crankcase 2 flange screw *

V2607-CR-E5 V2607-CR-E5
V3307-CR-TE5
127.5 to 137.3 N·m 137.3 to 147.1 N·m 49.0 to 55.9 N·m
V2607-CR-TE5 13.01 to 14.00 kgf·m 14.00 to 15.00 kgf·m V2607-CR-TE5 5.00 to 5.70 kgf·m
94.04 to 101.2 lbf·ft 101.3 to 108.4 lbf·ft 36.2 to 41.2 lbf·ft
V3307-CR-TIE5
V2607-CR-TIE5 V2607-CR-TIE5

Crankcase 2 flange screw * Connecting rod screw * Connecting rod screw *

V2607-CR-E5
V3307-CR-TE5 V3307-CR-TE5
58.8 to 63.7 N·m 40.0 to 45.0 N·m 68.6 to 73.5 N·m
6.00 to 6.49 kgf·m V2607-CR-TE5 4.08 to 4.58 kgf·m 7.00 to 7.49 kgf·m
43.4 to 46.9 lbf·ft 29.5 to 33.1 lbf·ft 50.6 to 54.2 lbf·ft
V3307-CR-TIE5 V3307-CR-TIE5
V2607-CR-TIE5

© KUBOTA Corporation 2019
KiSC issued 08, 2019 A
 (2/8)

Camshaft set screw Camshaft set screw Idle gear mounting screw

V2607-CR-E5 V2607-CR-E5
V3307-CR-TE5
23.5 to 27.5 N·m 23.5 to 27.5 N·m 49.0 to 55.9 N·m
V2607-CR-TE5 2.40 to 2.80 kgf·m 2.40 to 2.80 kgf·m V2607-CR-TE5 5.00 to 5.70 kgf·m
17.4 to 20.2 lbf·ft 17.4 to 20.2 lbf·ft 36.2 to 41.2 lbf·ft
V3307-CR-TIE5
V2607-CR-TIE5 V2607-CR-TIE5

Idle gear mounting screw Crank pulsar gear mounting screw Flywheel housing mounting screw

V2607-CR-E5
V3307-CR-TE5
29.4 to 34.3 N·m 9.80 to 11.3 N·m 77.5 to 90.2 N·m
3.00 to 3.49 kgf·m All Models 1.00 to 1.15 kgf·m V2607-CR-TE5 7.91 to 9.19 kgf·m
21.7 to 25.2 lbf·ft 7.23 to 8.33 lbf·ft 57.2 to 66.5 lbf·ft
V3307-CR-TIE5
V2607-CR-TIE5

Flywheel housing mounting screw Flywheel screw * Flywheel screw *

V2607-CR-E5
V3307-CR-TE5 V3307-CR-TE5
103.0 to 117.7 N·m 98.1 to 107 N·m 122.6 to 132.4 N·m
10.51 to 12.00 kgf·m V2607-CR-TE5 10.0 to 11.0 kgf·m 12.51 to 13.50 kgf·m
75.97 to 86.81 lbf·ft 72.4 to 79.5 lbf·ft 90.43 to 97.65 lbf·ft
V3307-CR-TIE5 V3307-CR-TIE5
V2607-CR-TIE5

KiSC issued 08, 2019 A

 (3/8)

Supply pump gear mounting nut Relief valve retaining plug Oil pump cover screw

58.8 to 68.6 N·m 68.6 to 78.5 N·m 7.84 to 9.31 N·m

All Models 6.00 to 6.99 kgf·m All Models 7.00 to 8.00 kgf·m All Models 0.800 to 0.949 kgf·m
43.4 to 50.5 lbf·ft 50.6 to 57.8 lbf·ft 5.79 to 6.86 lbf·ft

Front cover mounting screw Oil cooler joint screw Crankshaft screw *

29.4 to 34.3 N·m 63.7 to 73.5 N·m 255.0 to 274.6 N·m

All Models 3.00 to 3.49 kgf·m All Models 6.50 to 7.49 kgf·m All Models 26.01 to 28.00 kgf·m
21.7 to 25.2 lbf·ft 47.0 to 54.2 lbf·ft 188.1 to 202.5 lbf·ft

Fuel temperature sensor Suction control valve (SCV) mounting Cylinder head mounting screw *
screw

V2607-CR-E5
17.6 to 26.5 N·m 6.90 to 10.8 N·m 155 to 165 N·m
All Models 1.80 to 2.70 kgf·m All Models 0.704 to 1.10 kgf·m V2607-CR-TE5 15.8 to 16.8 kgf·m
13.0 to 19.5 lbf·ft 5.09 to 7.96 lbf·ft 115 to 121 lbf·ft
V2607-CR-TIE5

KiSC issued 08, 2019 A

 (4/8)

Cylinder head mounting screw * Cylinder head mounting screw Exhaust manifold mounting nut and screw
tightening order

(8) (4) (1) (5) (9)

(7) (3) (2) (6) (10)

V3307-CR-TE5
186 to 196 N·m 29.4 to 34.3 N·m
19.0 to 19.9 kgf·m All Models (1) → (10) All Models 3.00 to 3.49 kgf·m
138 to 144 lbf·ft 21.7 to 25.2 lbf·ft
V3307-CR-TIE5

Intake manifold mounting screw Rocker arm bracket screw * Rocker arm bracket screw *

V2607-CR-E5
V3307-CR-TE5
23.5 to 27.5 N·m 23.5 to 27.5 N·m 49.0 to 55.9 N·m
All Models 2.40 to 2.80 kgf·m V2607-CR-TE5 2.40 to 2.80 kgf·m 5.00 to 5.70 kgf·m
17.4 to 20.2 lbf·ft 17.4 to 20.2 lbf·ft 36.2 to 41.2 lbf·ft
V3307-CR-TIE5
V2607-CR-TIE5

Injector clamp washer nut Overflow pipe joint screw Cylinder head cover screw
(Injector side)

23.5 to 27.5 N·m 9.80 to 11.3 N·m 9.80 to 11.3 N·m

All Models 2.40 to 2.80 kgf·m All Models 1.00 to 1.15 kgf·m All Models 1.00 to 1.15 kgf·m
17.4 to 20.2 lbf·ft 7.23 to 8.33 lbf·ft 7.23 to 8.33 lbf·ft

KiSC issued 08, 2019 A

 (5/8)

Glow plug Glow lead mounting nut Overflow pipe joint screw
(Cylinder head side)

7.65 to 9.35 N·m 1.0 to 1.8 N·m 11 to 15 N·m

All Models 0.780 to 0.953 kgf·m All Models 0.11 to 0.18 kgf·m All Models 1.2 to 1.5 kgf·m
5.65 to 6.89 lbf·ft 0.74 to 1.3 lbf·ft 8.2 to 11 lbf·ft

Overflow pipe joint screw Overflow pipe joint screw Injection pipe retaining nut
(Common rail side) (Supply pump side)

7.90 to 12.7 N·m 7.90 to 12.7 N·m 22.54 to 36.26 N·m

All Models 0.806 to 1.29 kgf·m All Models 0.806 to 1.29 kgf·m All Models 2.299 to 3.697 kgf·m
5.83 to 9.36 lbf·ft 5.83 to 9.36 lbf·ft 16.63 to 26.74 lbf·ft

Intake throttle valve mounting screw Crankshaft position sensor mounting Camshaft position sensor mounting nut
screw

23.5 to 27.5 N·m 8.00 to 12.0 N·m 8.00 to 12.0 N·m

All Models 2.40 to 2.80 kgf·m All Models 0.816 to 1.22 kgf·m All Models 0.816 to 1.22 kgf·m
17.4 to 20.2 lbf·ft 5.90 to 8.85 lbf·ft 5.90 to 8.85 lbf·ft

KiSC issued 08, 2019 A

 (6/8)

Intake air temperature sensor Coolant temperature sensor Boost pressure sensor mounting screw

29.4 to 39.2 N·m 15.7 to 19.6 N·m 4.0 to 6.0 N·m

All Models 3.00 to 3.99 kgf·m All Models 1.60 to 1.99 kgf·m All Models 0.41 to 0.61 kgf·m
21.7 to 28.9 lbf·ft 11.6 to 14.4 lbf·ft 3.0 to 4.4 lbf·ft

EGR valve mounting screw EGR cooler flange screw Turbocharger assembly mounting nut

23.5 to 27.5 N·m 23.5 to 27.5 N·m 29.4 to 34.3 N·m

All Models 2.40 to 2.80 kgf·m All Models 2.40 to 2.80 kgf·m All Models 3.00 to 3.49 kgf·m
17.4 to 20.2 lbf·ft 17.4 to 20.2 lbf·ft 21.7 to 25.2 lbf·ft

Oil pipe joint screw Filter comp (DPF) mounting screw Filter comp (DPF) mounting bracket

V2607-CR-TE5

15.7 to 19.6 N·m V2607-CR-TIE5 49.0 to 63.7 N·m 16.0 to 20.0 N·m
All Models 1.60 to 1.99 kgf·m 5.00 to 6.49 kgf·m V2607-CR-E5 1.64 to 2.03 kgf·m
11.6 to 14.4 lbf·ft V3307-CR-TE5 36.2 to 46.9 lbf·ft 11.8 to 14.7

V3307-CR-TIE5

KiSC issued 08, 2019 A

 (7/8)

Exhaust gas temperature sensor ** Differential pressure pipe ** Muffler full assembly (DPF) mounting
screw

25.0 to 35.0 N·m 16.0 to 23.0 N·m 60.8 to 70.8 N·m

All Models 2.55 to 3.56 kgf·m All Models 1.64 to 2.34 kgf·m V2607-CR-E5 6.20 to 7.21 kgf·m
18.5 to 25.8 lbf·ft 11.8 to 16.9 lbf·ft 44.9 to 52.2 lbf·ft

Muffler full assembly (DPF) mounting Muffler flange nut Muffler flange nut
screw

V2607-CR-TE5 V2607-CR-TE5

V2607-CR-TIE5 60.8 to 70.8 N·m 29.4 to 34.3 N·m V2607-CR-TIE5 49.0 to 55.9 N·m
6.20 to 7.21 kgf·m V2607-CR-E5 3.00 to 3.49 kgf·m 5.00 to 5.70 kgf·m
V3307-CR-TE5 44.9 to 52.2 lbf·ft 21.7 to 25.2 lbf·ft V3307-CR-TE5 36.2 to 41.2 lbf·ft

V3307-CR-TIE5 V3307-CR-TIE5

Cooling fan mounting screw Starter B terminal nut Oil pressure switch

9.80 to 11.3 N·m 9.80 to 11.8 N·m 15.7 to 19.6 N·m

All Models 1.00 to 1.15 kgf·m All Models 1.00 to 1.20 kgf·m All Models 1.60 to 1.99 kgf·m
7.23 to 8.33 lbf·ft 7.23 to 8.70 lbf·ft 11.6 to 14.4 lbf·ft

KiSC issued 08, 2019 A

 (8/8)
(2) General Tightening Torques
Screw and bolt material grades are shown by numbers punched on the screw and bolt heads.
Prior to tightening, be sure to check out the numbers as shown below.
None or 4 : Standard grade
7 : Special grade
Nominal Diameter Standard Grade Special Grade
7.8 to 9.3 N·m 9.80 to 11.3 N·m
M6 0.80 to 0.94 kgf·m 1.00 to 1.15 kgf·m
5.8 to 6.8 lbf·ft 7.23 to 8.33 lbf·ft
17.7 to 20.6 N·m 23.5 to 27.5 N·m
M8 1.81 to 2.10 kgf·m 2.40 to 2.80 kgf·m
13.1 to 15.1 lbf·ft 17.4 to 20.2 lbf·ft
39.2 to 45.1 N·m 49.0 to 55.9 N·m
M10 4.00 to 4.59 kgf·m 5.00 to 5.70 kgf·m
29.0 to 33.2 lbf·ft 36.2 to 41.2 lbf·ft
62.8 to 72.6 N·m 77.5 to 90.2 N·m
M12 6.41 to 7.40 kgf·m 7.91 to 9.19 kgf·m
46.4 to 53.5 lbf·ft 57.2 to 66.5 lbf·ft

KiSC issued 08, 2019 A