Footing Pile Cap Design

Project : Footing Number : Engineer :

1.Input Data SI-Units FPS-Units 5.Pile Arrangement
Column. width (b) = 0.6 m 23.6 in
Column. depth (h) = 0.6 m 23.6 in U
2.Material Properties X - direction
number of row
number of pile on each row
Rebar fy = 500 Mpa 72.5 ksi spacing between pile
spacing at edge of footing
Concrete fc' = 25 Mpa 3.6 ksi total length
dx-1
dx-2
Modulus of Elasticity steel bars (Es) = 200,000 Mpa 29007.6 ksi
Modulus of Elasticity of Concrete (Ec) = 23,500 Mpa 3408.4 ksi
n = 9

3.Pile data (From Geo-Technical Report)

Pile diameter/width (D) = 1.5 m 59.1 in
safe load of pile (Capacity) = 900 KN 202.3 Kip
length of Pile (L) 6 m 236.2 in
4.Loadind Data
Axial Load (Px) = 0 KN 0.0 Kip
Axial Load (Py) 0 KN 0.0 Kip
Axial Load (Pz) 9,701 KN 2180.9 Kip
Mx = 128 KN-m 94.4 Kip-ft
My = 6 KN-m 4.2 Kip-ft
Mz = 0 KN-m 0.0 Kip-ft

4. Spring Constant or Point Spring (Kv)

Area of Cross Section of Pile (A) = 1.7671 m2 0.4 in2
Spring Constant (K=(EA/L) = 6,921,321 KN/m 39521.8 kip/in
 Footing Pile Cap Design
Project : Footing Number : Engineer :

𝑘=𝐹/∆
 Footing Pile Cap Design
Project : Footing Number : Engineer :
gn
Date :
Type of Pile cap Footing can be used
Required No. of Piles = 12.6
Use number of total pile = 13.0
X - direction FPS-Units Y - direction FPS-Units
3 number of column 4
pile on each row 4 number of pile on each column 3
4.5 m 177.2 inch spacing between pile 4.5 m 177.2 inch
edge of footing 1.5 m 59.1 inch spacing at edge of footing 1.5 m 59.1 inch
16.5 m 649.6 inch total width 12 m 472.5 inch
4.5 m 177.2 inch dy-1 4.5 m 177.2 inch 11
0 m 0.0 inch dy-2 0 m 0.0 inch
2.25 21

11

21

11

21

31

11

21
gn
Date :
31

Remarks
1 "dx" is the distance from the center of pile to
2 "dy" is the distance from the center of pile to
Download 3 "d at X-dir" is the distance from the center of
4 "d at Y-dir" is the distance from the center of
5 if d at X-dir or Y-dir are negative sign, it mea
in other words, positive means outside
www.civilmdc.com 6 "arm X-dir" is distance in Y-dir to be induced
7 "arm Y-dir" is distance in X-dir to be induced
8 reinforcement in X-dir must be determined by
9 reinforcement in Y-dir must be determined by
10 input moment "Mx" have to be located in X-d
11 when "actual distance" in subject "checking s

h/2 h/2+d/2
11 12 13

dx COL.
21 22 23
X

d/2
d 31 32 33

for beam shear dy1

Y dy2
pe of Pile cap Footing can be used in this sheet
Y

11 12
X
21 22

12 13
X
22 23

12 13 14
X
22 23 24

12 13

22 23 X

32 33

12 13 14

22 23 24 X
 32 33 34

e distance from the center of pile to the X-axis (parallel ot Y-axis)

e distance from the center of pile to the Y-axis (parallel ot X-axis)
r" is the distance from the center of pile to the critical section on X-axis
r" is the distance from the center of pile to the critical section on Y-axis
dir or Y-dir are negative sign, it means that the pile is located inside the critical section
words, positive means outside
ir" is distance in Y-dir to be induced moment about X-axis or Mx
ir" is distance in X-dir to be induced moment about Y-axis or My
ment in X-dir must be determined by "My" and bar arrangement is located in X-dir
ment in Y-dir must be determined by "Mx" and bar arrangement is located in Y-dir
ment "Mx" have to be located in X-dir and always have greater values than "My"
ual distance" in subject "checking shear" is input, the "sign of the distance have to be check and input follow the "actual value"
3?
h/2 h/2+d/2
11 12 13 14 1?

b/2+d/2 3?
COL.
21 22 23 24
b/2

for punching shear

d/2
31 32 33 34

ear dy1
Y dy2