Quantum using EcoStruxure™ Control Expert

35010574 12/2018

Quantum using
EcoStruxure™
Control Expert
Experts and Communication
Reference Manual
(Original Document)

12/2018
35010574.15

www.schneider-electric.com
 The information provided in this documentation contains general descriptions and/or technical
characteristics of the performance of the products contained herein. This documentation is not
intended as a substitute for and is not to be used for determining suitability or reliability of these
products for specific user applications. It is the duty of any such user or integrator to perform the
appropriate and complete risk analysis, evaluation and testing of the products with respect to the
relevant specific application or use thereof. Neither Schneider Electric nor any of its affiliates or
subsidiaries shall be responsible or liable for misuse of the information contained herein. If you
have any suggestions for improvements or amendments or have found errors in this publication,
please notify us.
You agree not to reproduce, other than for your own personal, noncommercial use, all or part of
this document on any medium whatsoever without permission of Schneider Electric, given in
writing. You also agree not to establish any hypertext links to this document or its content.
Schneider Electric does not grant any right or license for the personal and noncommercial use of
the document or its content, except for a non-exclusive license to consult it on an "as is" basis, at
your own risk. All other rights are reserved.
All pertinent state, regional, and local safety regulations must be observed when installing and
using this product. For reasons of safety and to help ensure compliance with documented system
data, only the manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant
instructions must be followed.
Failure to use Schneider Electric software or approved software with our hardware products may
result in injury, harm, or improper operating results.
Failure to observe this information can result in injury or equipment damage.
© 2018 Schneider Electric. All rights reserved.

2 35010574 12/2018
 Table of Contents

Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Part I Software Configuration . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 1 Module Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Mapping a Local Quantum I/O Station . . . . . . . . . . . . . . . . . . . . . . . . 18
Open the Parameter Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Chapter 2 Quantum Addressing Modes . . . . . . . . . . . . . . . . . . . . . 21
Flat Addressing—800 Series I/O Modules . . . . . . . . . . . . . . . . . . . . . 22
Topological Addressing—800 Series I/O Modules with Control Expert 23
IODDT Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Quantum IODDTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Addressing Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Discrete I/O Bit Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
I/O Module Status Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Part II Quantum Remote I/O (RIO) Modules . . . . . . . . . . . . 33
Chapter 3 140 CRP 931 00: Remote I/O (RIO) Head Module (single
channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Chapter 4 140 CRP 932 00: Remote I/O (RIO) Head Module (dual
channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Chapter 5 140 CRA 931 00: Remote I/O (RIO) Drop Module (single
channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

35010574 12/2018 3
 Chapter 6 140 CRA 932 00: Remote I/O (RIO) Drop Module (dual
channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Chapter 7 140 NRP 954 00: Fiber Optic Repeater Module
(Multimode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
LED Indicators and Diagnostic Relay Behavior . . . . . . . . . . . . . . . . . . 63
Module Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Chapter 8 140 NRP 954 01C: Fiber Optic Repeater Module (Single-
mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
LED Indicators and Diagnostic Relay Behavior . . . . . . . . . . . . . . . . . . 83
Module Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Part III Quantum Distributed I/O (DIO) Drop Modules . . . . . 99
Chapter 9 Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Configuring a Quantum DIO Drop . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Chapter 10 140 CRA 211 10: DIO Drop Module 115/230 VAC (single
channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Chapter 11 140 CRA 212 10: DIO Drop Module 115/230 VAC (dual
channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

4 35010574 12/2018
 Chapter 12 140 CRA 211 20: DIO Drop Module 24 VDC (single
channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Chapter 13 140 CRA 212 20: DIO Drop Module 24 VDC (dual
channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Part IV Modbus Plus Network Option Modules (NOM) . . . . . 137
Chapter 14 140 NOM 211 00: Modbus Plus Option Module . . . . . . . 139
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Chapter 15 140 NOM 212 00: Modbus Plus Option Module . . . . . . . 151
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Chapter 16 140 NOM 252 00: Modbus Plus Option Module 10Base-
FL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Fiber Optic Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Part V Quantum Ethernet Modules . . . . . . . . . . . . . . . . . . . 183
Chapter 17 140 NOE xxx xx: Ethernet Module General Overview . . 185
General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Modicon Quantum Ethernet Modules Overview . . . . . . . . . . . . . . . . . 187
Indicators for Ethernet Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192

35010574 12/2018 5
 Chapter 18 140 NOE 211 x0: TCP/IP 10Base-T Ethernet Module . . . 195
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Chapter 19 140 NOE 251 x0: TCP/IP 10Base-FL Ethernet Module . . 201
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Chapter 20 140 NOE 311 00: SY/MAX 10Base-T Ethernet Module . . 207
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Chapter 21 140 NOE 351 00: SY/MAX 10Base-FL Ethernet Module . 213
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Chapter 22 140 NOE 771 00: TCP/IP 10/100 Ethernet Module . . . . . 219
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Chapter 23 140 NOE 771 01: TCP/IP 10/100 Ethernet Module . . . . . 225
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
Chapter 24 140 NOE 771 10: TCP/IP 10/100 FactoryCast Ethernet
Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
Chapter 25 140 NOE 771 11: TCP/IP 10/100 FactoryCast Ethernet
Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243

6 35010574 12/2018
 Chapter 26 140 NWM 100 00: TCP/IP 10/100 FactoryCast HMI
Ethernet Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Part VI Quantum Field Bus Modules . . . . . . . . . . . . . . . . . . 249
Chapter 27 140 EIA 921 00: AS-i Master Communication Module . . 251
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Parameter Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Part VII Quantum Special Purpose / Intelligent Modules . . . . 261
Chapter 28 140 HLI 340 00: High Speed Latch and Interrupt Module 263
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
Addressing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
Parameter Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Chapter 29 140 EHC 202 00: High Speed Counter Module . . . . . . . 273
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
Controlling and Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Operating Conditions and Examples . . . . . . . . . . . . . . . . . . . . . . . . . . 282
Addressing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
I/O Map and Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
Parameter Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312

35010574 12/2018 7
 Chapter 30 140 EHC 105 00: High Speed Counter Module . . . . . . . . 317
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Parameter Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333

8 35010574 12/2018
 Safety Information

Important Information

NOTICE
Read these instructions carefully, and look at the equipment to become familiar with the device
before trying to install, operate, service, or maintain it. The following special messages may appear
throughout this documentation or on the equipment to warn of potential hazards or to call attention
to information that clarifies or simplifies a procedure.

35010574 12/2018 9
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by qualified
personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of
the use of this material.
A qualified person is one who has skills and knowledge related to the construction and operation
of electrical equipment and its installation, and has received safety training to recognize and avoid
the hazards involved.

BEFORE YOU BEGIN

Do not use this product on machinery lacking effective point-of-operation guarding. Lack of
effective point-of-operation guarding on a machine can result in serious injury to the operator of
that machine.

WARNING
UNGUARDED EQUIPMENT
 Do not use this software and related automation equipment on equipment which does not have
point-of-operation protection.
 Do not reach into machinery during operation.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

This automation equipment and related software is used to control a variety of industrial processes.
The type or model of automation equipment suitable for each application will vary depending on
factors such as the control function required, degree of protection required, production methods,
unusual conditions, government regulations, etc. In some applications, more than one processor
may be required, as when backup redundancy is needed.
Only you, the user, machine builder or system integrator can be aware of all the conditions and
factors present during setup, operation, and maintenance of the machine and, therefore, can
determine the automation equipment and the related safeties and interlocks which can be properly
used. When selecting automation and control equipment and related software for a particular
application, you should refer to the applicable local and national standards and regulations. The
National Safety Council's Accident Prevention Manual (nationally recognized in the United States
of America) also provides much useful information.
In some applications, such as packaging machinery, additional operator protection such as point-
of-operation guarding must be provided. This is necessary if the operator's hands and other parts
of the body are free to enter the pinch points or other hazardous areas and serious injury can occur.
Software products alone cannot protect an operator from injury. For this reason the software
cannot be substituted for or take the place of point-of-operation protection.

10 35010574 12/2018
 Ensure that appropriate safeties and mechanical/electrical interlocks related to point-of-operation
protection have been installed and are operational before placing the equipment into service. All
interlocks and safeties related to point-of-operation protection must be coordinated with the related
automation equipment and software programming.
NOTE: Coordination of safeties and mechanical/electrical interlocks for point-of-operation
protection is outside the scope of the Function Block Library, System User Guide, or other
implementation referenced in this documentation.

START-UP AND TEST

Before using electrical control and automation equipment for regular operation after installation,
the system should be given a start-up test by qualified personnel to verify correct operation of the
equipment. It is important that arrangements for such a check be made and that enough time is
allowed to perform complete and satisfactory testing.

WARNING
EQUIPMENT OPERATION HAZARD
 Verify that all installation and set up procedures have been completed.
 Before operational tests are performed, remove all blocks or other temporary holding means
used for shipment from all component devices.
 Remove tools, meters, and debris from equipment.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

Follow all start-up tests recommended in the equipment documentation. Store all equipment
documentation for future references.
Software testing must be done in both simulated and real environments.
Verify that the completed system is free from all short circuits and temporary grounds that are not
installed according to local regulations (according to the National Electrical Code in the U.S.A, for
instance). If high-potential voltage testing is necessary, follow recommendations in equipment
documentation to prevent accidental equipment damage.
Before energizing equipment:
 Remove tools, meters, and debris from equipment.
 Close the equipment enclosure door.
 Remove all temporary grounds from incoming power lines.
 Perform all start-up tests recommended by the manufacturer.

35010574 12/2018 11
OPERATION AND ADJUSTMENTS
The following precautions are from the NEMA Standards Publication ICS 7.1-1995 (English
version prevails):
 Regardless of the care exercised in the design and manufacture of equipment or in the selection
and ratings of components, there are hazards that can be encountered if such equipment is
improperly operated.
 It is sometimes possible to misadjust the equipment and thus produce unsatisfactory or unsafe
operation. Always use the manufacturer’s instructions as a guide for functional adjustments.
Personnel who have access to these adjustments should be familiar with the equipment
manufacturer’s instructions and the machinery used with the electrical equipment.
 Only those operational adjustments actually required by the operator should be accessible to
the operator. Access to other controls should be restricted to prevent unauthorized changes in
operating characteristics.

12 35010574 12/2018
 About the Book

At a Glance

Document Scope
This document is the reference for the networking, communication, and special purpose modules
of the Quantum automation system with Control Expert.

Validity Note
This document is valid for EcoStruxure™ Control Expert 14.0 or later.
The technical characteristics of the devices described in the present document also appear online.
To access the information online:

Step Action
1 Go to the Schneider Electric home page www.schneider-electric.com.
2 In the Search box type the reference of a product or the name of a product range.
 Do not include blank spaces in the reference or product range.
 To get information on grouping similar modules, use asterisks (*).

3 If you entered a reference, go to the Product Datasheets search results and click on the
reference that interests you.
If you entered the name of a product range, go to the Product Ranges search results and click
on the product range that interests you.
4 If more than one reference appears in the Products search results, click on the reference that
interests you.
5 Depending on the size of your screen, you may need to scroll down to see the data sheet.
6 To save or print a data sheet as a .pdf file, click Download XXX product datasheet.

The characteristics that are presented in the present document should be the same as those
characteristics that appear online. In line with our policy of constant improvement, we may revise
content over time to improve clarity and accuracy. If you see a difference between the document
and online information, use the online information as your reference.

Related Documents

Title of Documentation Reference Number

Modicon Modbus Plus Network, Planning and Installation Guide 31003525

You can download these technical publications and other technical information from our website
at https://www.schneider-electric.com/en/download

35010574 12/2018 13
Product Related Information

WARNING
UNINTENDED EQUIPMENT OPERATION
The application of this product requires expertise in the design and programming of control
systems. Only persons with such expertise should be allowed to program, install, alter, and apply
this product.
Follow all local and national safety codes and standards.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

14 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
Software Configuration
35010574 12/2018

Part I
Software Configuration

Software Configuration

Introduction
This part provides information on the Software Configuration of the networking and
intelligent/special purpose modules.

What Is in This Part?

This part contains the following chapters:
Chapter Chapter Name Page
1 Module Configuration 17
2 Quantum Addressing Modes 21

35010574 12/2018 15
Software Configuration

16 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
Module Configuration
35010574 12/2018

Chapter 1
Module Configuration

Module Configuration

Purpose
This chapter provides information on software configuration of the module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Mapping a Local Quantum I/O Station 18
Open the Parameter Configuration 19

35010574 12/2018 17
Module Configuration

Mapping a Local Quantum I/O Station

Overview
Use the following dialog to map an existing local Quantum I/O station with a new module.

Inserting a module (local)

This table shows the steps required for inserting a module in a local station.

Step Action
1 Call the Bus Editor
2 Mark a free slot in the local station (left mouse button)
3 Move the mouse pointer over the marked slot
4 Click on the right mouse button
Result: A shortcut menu is opened

5 Select New Device

Result: A dialog window opens that displays available modules
6 Select the desired module from the respective category in the Hardware catalog.
Result: The new module is inserted in the empty slot on the local station.

18 35010574 12/2018
 Module Configuration

Open the Parameter Configuration

Overview
The following dialog box enables you to call the parameter configuration for a module.
An explanation of the individual parameters can be found in the respective module chapters.

Open the Parameter Configuration

This table shows the steps required to open the parameter configuration.

Step Action
1 Call the Bus Editor
2 Select the module
3 Click on the right mouse button
Result: A shortcut menu is opened

4 Select Open Module

Result: The module opens with the parameter configuration window

35010574 12/2018 19
Module Configuration

20 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
Addressing Modes
35010574 12/2018

Chapter 2
Quantum Addressing Modes

Quantum Addressing Modes

Purpose
This chapter provides information on the three different modes Control Expert allows to address
the I/O data from a Quantum I/O module:
 Flat Addressing
 Topological Addressing
 IODDT Addressing

NOTE: Topological addresses overlapping (%IWr.m.c) is not supported by Quantum application,

use flat addressing (%IWx) when memory overlapping control is needed.
NOTE: The different addressing modes refer to the same physical location in the PLC memory for
a given data point.
While Flat Addressing and Topological Addressing are available for all Quantum I/O modules,
IODDTs are only provided for modules that deliver information in addition to the I/O values (e.g.
errors or warnings).
Also provided is information about I/O module status bytes and bit order.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Flat Addressing—800 Series I/O Modules 22
Topological Addressing—800 Series I/O Modules with Control Expert 23
IODDT Addressing 24
Quantum IODDTs 25
Addressing Example 27
Discrete I/O Bit Numbering 28
I/O Module Status Byte 29

35010574 12/2018 21
Addressing Modes

Flat Addressing—800 Series I/O Modules

Introduction
800 series I/O modules follow a system of flat address mapping in Control Expert. To work
properly. each module requires a determinate number of bits and/or words. The IEC addressing
system is equivalent to the 984LL register addressing. Use the following assignments:
 0x is now %Mx
 1x is now %Ix
 3x is now %IWx
 4x is now %MWx
The following table shows the relationship between 984LL notation and IEC notation.

Outputs and 984LL Notation IEC Notation

Inputs Register Addresses System Bits and Words Memory Addresses I/O Addresses
output 0x System Bit %Mx %Qx
input 1x System Bit %Ix %Ix
input 3x System Word %IWx %IWx
output 4x System Word %MWx %QWx

To access the I/O data of a module,

Step Action
1 Enter the address range in the configuration screen.

Examples
The following examples show the relationship between 984LL register addressing and IEC
addressing:
000001 is now %M1
100101 is now %I101
301024 is now %IW1024
400010 is now %MW10

22 35010574 12/2018
 Addressing Modes

Topological Addressing—800 Series I/O Modules with Control Expert

Accessing I/O Data Values

Use topological addressing to access I/O data items. Identify the topological location of the module
within an 800 series I/O module with Control Expert using the following notation:
%<Exchangetype><Objecttype>[\b.e\]r.m.c[.rank]
where:
 b = bus
 e = equipment (drop)
 r = rack
 m = module slot
 c = channel
NOTE: When addressing,
1. The [\b.e\] defaults to \1.1\ in a local rack and does not need to be specified.
2. The rank is an index used to identify different properties of an object with the same data type
(value, warning level, error level).
3. The rank numbering is zero-based, and if the rank is zero, omit the entry.
For detailed information on I/O variables, please refer to the EcoStruxure™ Control Expert,
Program Languages and Structure, Reference Manual.

Reading Values: An Example

To read Action
input value (rank = 0) from channel 7 of an analog module Enter
located in slot 6 of a local rack: %IW1.6.7[.0]
input value (rank = 0) from channel 7 of an analog module Enter
located in slot 6 of drop 3 of RIO bus 2: %IW\2.3\1.6.7[.0]
’out of range’ value (rank = 1) from channel 7 of an analog Enter
module located in slot 6 of a local rack: %I1.6.7.1[.0]

35010574 12/2018 23
Addressing Modes

IODDT Addressing

IODDT Addressing
An IODDT allows all information (bits and registers) related to a channel to be handled through a
user-defined variable. This variable is defined in the Control Expert data editor by selecting the
appropriate IODDT for the module as a data type and specifying the topological address of the
module using the following syntax:
%CH[\b.e\]r.m.c
where:
 b = bus
 e = equipment (drop)
 r = rack
 m = module slot
 c = channel
Here is an example of an IODDT for a thermocouple input module in slot 4 of a local rack:

Variables in the User Program

You can access all information related to channel 1 of the module using the following variables:
 My_Temp_Point1.VALUE for the measured value
 My_Temp_Point1.ERROR indicating an out-of-range condition
 My_Temp_Point1.WARNING indicating an over-range condition

24 35010574 12/2018
 Addressing Modes

Quantum IODDTs

Introduction
Control Expert provides a couple of IODDTs which are either generic and can be used for several
I/O modules or belong to one specific module.
NOTE: Deviating from the general description of the data types in the Direct Addressing Data
Instances chapter in the EcoStruxure™ Control Expert Reference Manual, in Quantum IODDTs for
analog modules and expert modules the data type Bool is used for %I and %Q.

T_ANA_IN_VE
T_ANA_IN_VE is used with all channels of the following I/O modules:
 ACI 030 00
 AII 330 10
 ACI 040 00
 ACI 040 00

IODDT for analog input modules supporting Value and Error

Object Symbol Rank Description

%IW VALUE 0 Input value
%I ERROR 1 Input error

T_ANA_IN_VWE
T_ANA_IN_VWE is used with all channels of the following I/O modules:
 ARI 030 10,
 AVI 030 00
 ATI 030 00
 AII 330 00
and
 Channels 3 and 4 of AMM 090 00

IODDT for analog input modules supporting Value, Warning and Error

Object Symbol Rank Description

%IW VALUE 0 Input value
%I ERROR 1 Input error
%I WARNING 2 Input warning

35010574 12/2018 25
Addressing Modes

T_ANA_BI_VWE
T_ANA_BI_VWE is used with the following I/O modules:
 Channels 1 and 2 of AMM 090 00
IODDT for bidirectional analog modules supporting Value, Warning and Error

Object Symbol Rank Description

%IW VALUE_IN 0 Input value
%QW VALUE_OUT 0 Output value
%I ERROR_IN 1 Input error
%I WARNING 2 Input warning
%I ERROR_OUT 3 Output error

T_CNT_105
T_CNT_105 is used with all channels of the following I/O modules:
 EHC 105
Specific IODDT for high speed counter module EHC 105

Object Symbol Rank Description

%IW VALUE_L 1 Input value: Low word
%IW VALUE_H 2 Input value: High word
%I ERROR 1 Error in Counter
%I SP_FINAL 2 Final Set Point signal
%I SP_FIRST 3 First Set Point signal
%I SP_SECOND 4 Second Set Point signal
%QW STOP_VALUE 1 For CNT_DIR="0", final set point
value
%QW INITIAL_VALUE 2 For CNT_R="1", initial set point value
%Q LS 1 "1", Counter load/start (controlled by
the rising edge)
%Q RSTART 2 "1", Counter restart (controlled by the
rising edge)
%Q OUT_OFF 3 "1", Counter output switch-off
%Q CNT_DIR 4 "0" Counter counts up
"1" Counter counts down
%Q OM1 5 Operating Mode bit 1
%Q OM2 6 Operating Mode bit 2
%Q OM3 7 Operating Mode bit 3
%Q OM4 8 Operating Mode bit 4

26 35010574 12/2018
 Addressing Modes

Addressing Example

Comparing the 3 Addressing Modes

The following example compares the 3 possible addressing modes. An 8-channel thermocouple
140 ATI 030 00 module with the following configuration data is used:
 mounted in slot 5 of the CPU rack (local rack)
 starting input address is 201 (input word %IW201)
 end input address is 210 (input word %IW210)
To access the I/O data from the module you can use the following syntax:

Module data Flat Topological IODDT Addressing Concept

Addressing Addressing Addressing
Channel 3 %IW203 %IW1.5.3 My_Temp.VALUE 300203
temperature
Channel 3 %IW209.5 %I1.5.3.1 My_Temp.ERROR 300209
out of range Bit 5 to be
extracted by user
logic
Channel 3 %IW209.13 %I1.5.3.2 My_Temp.WARNING 300209
range warning Bit 13 to be
extracted by user
logic
Module internal %IW210 %IW1.5.10 not accessible through 300210
temperature IODDT

NOTE: For the IODDT the data type T_ANA_IN_VWE is used and the variable My_Temp with the
address %CH1.5.10 was defined.
For comparison, the register addressing as used with Concept is added in the last column. As
Concept does not support direct addressing of a bit in a word, the bit extraction has to be performed
in the user program.

35010574 12/2018 27
Addressing Modes

Discrete I/O Bit Numbering

Introduction
The numbering of channels of an I/O module usually starts with 1 and counts up to the maximum
number of supported channels. The software however starts numbering with a 0 for the least
significant bit in a word (LSB). The Quantum I/O modules have their lowest channel mapped to the
most significant bit (MSB).
The following figure shows the mapping of I/O channels related to the bits in a word:.

Word Addressing Versus Bit Addressing

Mainly discrete I/O modules can be configured to deliver their I/O data either in word format or in
bit format. This can be selected during configuration by selecting either %IW (%MW) or %I (%M). If
you need to access a single bit from an I/O module configured to use an I/O word, you can use the
syntax %word.bit. The following table gives you the connection between I/O point number and
the associated I/O address in bit and word addressing.
The table shows a 32-point input module in the main rack, slot 4 configured with starting address
%I1 or %IW1:

I/O Bit address Bit address Bit address Bit address

channel (flat addressing) (topological extracted from word extracted from word
addressing) (flat addressing) (topological addressing)
1 %I1 %I1.4.1[.0] %IW1.15 %IW1.4.1.1.15
2 %I2 %I1.4.2[.0] %IW1.14 %IW1.4.1.1.14
3 %I3 %I1.4.3[.0] %IW1.13 %IW1.4.1.1.13
•••
15 %I15 %I1.4.15[.0] %IW1.1 %IW1.4.1.1.1
16 %I16 %I1.4.16[.0] %IW1.0 %IW1.4.1.1.0
17 %I17 %I1.4.17[.0] %IW2.15 %IW1.4.1.2.15
18 %I18 %I1.4.18[.0] %IW2.14 %IW1.4.1.2.14
•••
31 %I31 %I1.4.31[.0] %IW2.1 %IW1.4.1.2.1
32 %I32 %I1.4.32[.0] %IW2.0 %IW1.4.1.2.0

28 35010574 12/2018
 Addressing Modes

I/O Module Status Byte

Addressing Module Status Data

In addition to possible channel related diagnostics data, a module related status byte may be used.
The status information of all modules in a drop is administered by a table of %IW words. The starting
address of this table can be entered in the configuration screen for the drop.
This information is not accessible through topological addressing.
NOTE: The status information is only available if the module supports a status byte. For the
meaning of the status byte, check the module descriptions.
Example of a drop configuration screen with the starting address of the status table set to 100:

35010574 12/2018 29
Addressing Modes

The following illustration shows how one word of the table conveys the status information for two
modules:

30 35010574 12/2018
 Addressing Modes

Example
The following example shows a rack and the corresponding I/O status bytes displayed in an
animation table. The drop is configured to start at word %IW100 and allocates 16 words. This
represents the local and expansion rack, and assumes they are 16 slot racks.
If a module does not have have a status byte associated with the module or the slot is empty, then
the byte = 0.
Rack configuration and animation table:

Relation between slot, input word and status byte. The byte related to the module is marked:

Slot Input Value Module Module

Word
1 %IW[0] 0 power supply no status byte
2 0 CPU no status byte
3 %IW[1] 2#1000_0000_0000_0000 CPU no status byte
4 2#1000_0000_0000_0000 AVI At least one
channel is not
operating correctly.

35010574 12/2018 31
Addressing Modes

Slot Input Value Module Module

Word
5 %IW[2] 2#0000_0000_0000_1111 ATI Channels 1 ... 4
are not operating
correctly.
6 2#0000_0000_0000_1111 140 CRP 93• 00 no status byte
NOTE: If you install 2#1101_1110_0000_0000 140 CRP 312 00 CRP status byte1
a 140 CRP 312 00
remote I/O head
module on the
local rack instead
of a
140 CRP 93• 00
module, then:
7 %IW[3] 0 empty
8 0 empty
9 %IW[4] 2#0000_0000_0011_1111 DDO All channels are
not operating
correctly.
10 2#0000_0000_0011_1111 XBE no status byte
•••

1 If you install a 140 CRP 312 00 remote I/O head module on the local rack instead of a
140 CRP 93• 00 module, the status byte is the ETH_STATUS detailed in the Device DDT Names
topic in the Quantum EIO Remote I/O Modules Installation and Configuration Guide.

32 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
Remote I/O (RIO) Modules
35010574 12/2018

Part II
Quantum Remote I/O (RIO) Modules

Quantum Remote I/O (RIO) Modules

Introduction
This part provides information on the following Quantum RIO modules:

RIO Module Drop Location Communication Channels Bus Current

Required
140 CRA 931 00 Remote (Drop) 1 600 mA
140 CRA 932 00 Remote (Drop) 2 750 mA
140 CRP 931 00 Local (Head) 1 600 mA
140 CRP 932 00 Local (Head) 2 750 mA
140 NRP 954 00 Local (Head) or 2, multimode fiber optic 700 mA
Remote (Drop) (ST type); 1 coaxial (F type)
140 NRP 954 01C Local (Head) or 2, single-mode fiber optic 750 mA
Remote (Drop) (LC type); 1 coaxial (F type)

NOTE: For detailed information see also Product Related Information, page 14, Modicon Remote
I/O Cable System Planning and Installation Guide

What Is in This Part?

This part contains the following chapters:
Chapter Chapter Name Page
3 140 CRP 931 00: Remote I/O (RIO) Head Module (single channel) 35
4 140 CRP 932 00: Remote I/O (RIO) Head Module (dual channel) 41
5 140 CRA 931 00: Remote I/O (RIO) Drop Module (single channel) 47
6 140 CRA 932 00: Remote I/O (RIO) Drop Module (dual channel) 53
7 140 NRP 954 00: Fiber Optic Repeater Module (Multimode) 59
8 140 NRP 954 01C: Fiber Optic Repeater Module (Single-mode) 79

35010574 12/2018 33
Remote I/O (RIO) Modules

34 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
140 CRP 931 00
35010574 12/2018

Chapter 3
140 CRP 931 00: Remote I/O (RIO) Head Module (single channel)

140 CRP 931 00: Remote I/O (RIO) Head Module (single
channel)

Purpose
This chapter contains information of the 140 CRP 931 00 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 36
Indicators 37
Error Codes 38
Specifications 40

35010574 12/2018 35
140 CRP 931 00

Presentation

Function
The Remote I/O Head single channel modules are installed in the same backplane as the system
controlling CPU modules. The RIO head is used to transfer data bi-directionally between the CPU
and RIO drop modules installed in separate backplanes. A coaxial cable network is used to
interconnect the RIO head module and one or more RIO drop modules.

Illustration
The following figure shows the Remote I/O (RIO) module’s parts.

1 LED Area
2 RIO Coax Connector
3 Version Label
4 Model Number, Module Description, Color Code
5 Removable Door
6 Customer Identification Label (Fold label and place it inside door)

NOTE: To mantain CE compliance with the European Directive on EMC (89/336/EEC), the RIO
head module must be connected using quad shielded cable (see the Remote I/O Cable System
Planning and Installation Guide).

36 35010574 12/2018
 140 CRP 931 00

Indicators

Illustration
The following figure shows the LED indicators for the RIO Head module.

Description
The following table shows the LED descriptions for the RIO Head module.

LEDS Color Indication When On

Ready Green The module has passed powerup diagnostics.
Com Act Green The module is communicating on the RIO network (see the
following table for LED error codes).
Error A Red There is a loss of communication on Channel A with one or
more of the drops.

35010574 12/2018 37
140 CRP 931 00

Error Codes

Error Codes Table

The Blinking Com Act LED error codes for the RIO Head module table show the number of times
the Com Act LED on the RIO Head module blinks for each type of error and the crash codes for
each (all codes are in hex).
The following table shows the blinking Com Act LED error codes for the RIO Head module.

Number of Blinks Code Error

Slow (steady) 0000 Requested Kernal Mode
2 6820 hcb frame pattern error
6822 head cntrl blk diag error
6823 mod personality diag error
682A fatal start I/O error
682B bad read I/O pers request
682C bad execute diag request
6840 ASCII input xfer state
6841 ASCII output xfer state
6842 I/O input comm. state
6843 I/O output comm. state
6844 ASCII abort comm. state
6845 ASCII pause comm. state
6846 ASCII input comm. state
6847 ASCII output comm. state
6849 building 10 byte packet
684A building 12 byte packet
684B building 16 byte packet
684C illegal I/O drop number
3 6729 984 interface bus ack stuck high
4 6616 coax cable initialization error
6617 coax cable dma xfer error
6619 coax cable dumped data error
681A coax cable DRQ line hung
681C coax cable DRQ hung
5 6503 RAM address test error
6 6402 RAM data test error

38 35010574 12/2018
 140 CRP 931 00

7 6300 PROM checksum error (Exec not loaded)

6301 PROM checksum error
8 8001 Kernal PROM checksum error
8002 Flash prog / erase error
8003 Unexpected executive return

35010574 12/2018 39
140 CRP 931 00

Specifications

General Specifications
General Specifications

Bus Current required 600 mA

Power Dissipation 3W
(Typical)
Maximum Number of 1
CRPs supported by the
controller
Drop Type Quantum
200 Series
500 Series or
SY/MAX (any mix)
Drops 31 max
Words/Drop 64 In / 64 Out
ASCII 2 ports/drop, 32 ports (16 drops) max
Requires the use of:
AS-P892-000
AS-J892-101/102 or
AS-J290-0X0 at the RIO drops

Connection / Transmission
Connection / Transmission

Coax Termination Internal 75 ohms

Coax Shield Tied to chassis ground
Data Transfer Rate 1.544 Mb
Dynamic Range 35 dB
External Connections One "F" type female connector with a right angle adapter

Diagnostics
Diagnostics

Power Up Dual Port Memory Check

LAN Controller Check
Runtime Executive Checksum
RAM Address/Data

40 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
140 CRP 932 00
35010574 12/2018

Chapter 4
140 CRP 932 00: Remote I/O (RIO) Head Module (dual channel)

140 CRP 932 00: Remote I/O (RIO) Head Module (dual
channel)

Purpose
This chapter contains information of the 140 CRP 932 00 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 42
Indicators 43
Error Codes 44
Specifications 46

35010574 12/2018 41
140 CRP 932 00

Presentation

Function
The Remote I/O Head dual channel modules are installed in the same backplane as the system
controlling CPU modules. The RIO head is used to transfer data bi-directionally between the CPU
and RIO drop modules installed in separate backplanes. A coaxial cable network is used to
interconnect the RIO head module and one or more RIO drop modules.

Illustration
The following figure shows the Remote I/O (RIO) module’s parts.

1 LED Area
2 RIO Coax Connector (Channel A)
3 RIO Coax Connector (Channel B)
4 Version Label
5 Model Number, Module Description, Color Code
6 Removable Door
7 Customer Identification Label (Fold label and place it inside door)

NOTE: To mantain CE compliance with the European Directive on EMC (89/336/EEC), the RIO
head module must be connected using quad shielded cable (see the Remote I/O Cable System
Planning and Installation Guide).

42 35010574 12/2018
 140 CRP 932 00

Indicators

Illustration
The following figure shows the LED indicators for the RIO Head module.

Description
The following table shows the LED descriptions for the RIO Head module.

LEDS Color Indication When On

Ready Green The module has passed powerup diagnostics.
Com Act Green The module is communicating on the RIO network (see the
following table for LED error codes).
Error A Red There is a loss of communication on Channel A with one or
more of the drops.
Error B Red There is a loss of communication on Channel B with one or
more of the drops

35010574 12/2018 43
140 CRP 932 00

Error Codes

Error Codes Table

The Blinking Com Act LED error codes for the RIO Head module table show the number of times
the Com Act LED on the RIO Head module blinks for each type of error and the crash codes for
each (all codes are in hex).
The following table shows the blinking Com Act LED error codes for the RIO Head module.

Number of Blinks Code Error

Slow (steady) 0000 Requested Kernal Mode
2 6820 hcb frame pattern error
6822 head cntrl blk diag error
6823 mod personality diag error
682A fatal start I/O error
682B bad read I/O pers request
682C bad execute diag request
6840 ASCII input xfer state
6841 ASCII output xfer state
6842 I/O input comm. state
6843 I/O output comm. state
6844 ASCII abort comm. state
6845 ASCII pause comm. state
6846 ASCII input comm. state
6847 ASCII output comm. state
6849 building 10 byte packet
684A building 12 byte packet
684B building 16 byte packet
684C illegal I/O drop number
3 6729 984 interface bus ack stuck high
4 6616 coax cable initialization error
6617 coax cable dma xfer error
6619 coax cable dumped data error
681A coax cable DRQ line hung
681C coax cable DRQ hung
5 6503 RAM address test error
6 6402 RAM data test error

44 35010574 12/2018
 140 CRP 932 00

7 6300 PROM checksum error (Exec not loaded)

6301 PROM checksum error
8 8001 Kernal PROM checksum error
8002 Flash prog / erase error
8003 Unexpected executive return

NOTE: Error codes are available in the File and Device info screen (Crash Code field
(see EcoStruxure™ Control Expert, OS Loader, User Manual)) when using OS Loader.

35010574 12/2018 45
140 CRP 932 00

Specifications

General Specifications
General Specifications

Bus Current required 600 mA

Power Dissipation 3W
(Typical)
Maximum Number of 1
CRPs supported by the
controller
Drop Type Quantum
200 Series
500 Series
800 Series or
SY/MAX (any mix)
Drops 31 max
Words/Drop 64 In / 64 Out
ASCII 2 ports/drop, 32 ports (16 drops) max
Requires the use of:
AS-P892-000
AS-J892-101/102 or
AS-J290-0X0 at the RIO drops

Connection / Transmission
Connection / Transmission

Coax Termination Internal 75 ohms

Coax Shield Tied to chassis ground
Data Transfer Rate 1.544 Mb
Dynamic Range 35 dB
External Connections Two "F" type female connector with a right angle adapter

Diagnostics
Diagnostics

Power Up Dual Port Memory Check

LAN Controller Check
Runtime Executive Checksum
RAM Address/Data

46 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
140 CRA 931 00
35010574 12/2018

Chapter 5
140 CRA 931 00: Remote I/O (RIO) Drop Module (single channel)

140 CRA 931 00: Remote I/O (RIO) Drop Module (single
channel)

Purpose
This chapter contains information of the 140 CRA 931 00 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 48
Indicators 50
Error Codes 51
Specifications 52

35010574 12/2018 47
140 CRA 931 00

Presentation

Function
The Remote I/O Drop Single Channel modules are used to transfer data bi-directionally over a
coaxial cable network between I/O modules installed in the same (RIO drop) backplane and the
RIO head installed in the CPU backplane.

Illustration
The following figure shows the Remote I/O (RIO) module’s parts.

1 LED Area
2 RIO Coax Connector
3 Version Label
4 Model Number, Module Description, Color Code
5 Removable Door
6 Customer Identification Label (Fold label and place it inside door)

NOTE: To maintain CE compliance with the European Directive on EMC (89/336/EEC), the RIO
Head module must be connected using quad shielded cable (see the Remote I/O Cable System
Planning and Installation Guide).

48 35010574 12/2018
 140 CRA 931 00

Rear Panel Switches

Two rotary switches are located on the rear panel of the RIO Drop Modules and are used for setting
RIO drop addresses (refer to the illustration and table below).
SW1 (top switch) sets the upper digit (tens); SW2 (bottom switch) sets the lower digit (ones). The
illustration below shows the correct setting for an example address of 11.

Rear Panel Switches Figure

The following figure shows the SW1 top and SW2 bottom switches.

SW1 and SW2 Switches Table

The following table shows the node addresses of the SW1 and SW2 switches.

Node Address SW1 SW2

1 ... 9 0 1 ... 9
10 ... 19 1 0 ... 9
20 ... 29 2 0 ... 9
30 ... 32 3 0 ... 2

NOTE: Only addresses from 2 to 32 are valid

If "0" or an address greater than 32 is selected, the RIO module displays a flashing "Error A"- and
"Error B"-LED.
With Address "1" you don’t have flashing "Error A"- and "Error B"-LED.

35010574 12/2018 49
140 CRA 931 00

Indicators

Illustration
The following figure shows the LED indicators for the Drop module.

Description
The following table shows the RIO Drop module LED descriptions.

LEDS Color Indication when On

Ready Green The module has passed power-up diagnostics.
Com Act Green The module is communicating on the RIO network (see the following
table for LED error codes).
Fault Red Unable to communicate with one or more I/O modules.
Error A Red Communication error on Channel A.
Error B Red In combination with "Error A" to indicate an invalid Node address.

50 35010574 12/2018
 140 CRA 931 00

Error Codes

Error Codes Table

Blinking Com Act LED error codes for the RIO Drop module table show the number of times the
Com Act LED on the RIO Drop module blinks for each type of error and the crash codes for each
(all codes are in hex).
The following table shows the blinking Com Act LED error codes for the RIO Drop module.

Number of Blinks Code Description of Error

3 6701H ASIC test failure
4 6601H power down interrupt
6602H 82588 lan chip test error
6603H receive abort timeout
6604H transmission loop timeout
6605H transmission DMA error
6606H cable a initialization error
6607H cable a DMA xfer error
6608H cable b DMA xfer error
6609H cable a dumped data error
660AH cable a DRQ line hung
660BH cable b DRQ line hung
660CH cable a or b DRQ hung
660DH power-up lan controller error
5 6501H RAM address test error
6 6401H RAM data test error
7 6301H PROM checksum error

35010574 12/2018 51
140 CRA 931 00

Specifications

General Specifications
General Specifications

Bus Current required 600 mA

Power Dissipation 3W
(Typical)
I/O Type Quantum
Modules/Drop 14 max.
28 max. with Backplane expander (XBE)
Words/Drop 64 IN / 64 OUT
Holdup Time Software configurable

NOTE: You can specify a monitoring time of 3 - 65 535 in this text box. With communication
interruptions with the remote processor, the output modules will maintain their last operating
condition during that time. Once the monitoring time has expired, the output modules will reset to
their default timeout status. The monitoring time does not influence input modules. The CPU will
immediately set the input value to zero.

Connection / Transmission
Connection / Transmission

Coax Termination Internal 75 ohms

Coax Shield Capacitor to ground
Data Transfer Rate 1.544 Mb
Dynamic Range 35 dB
External Connections One "F" type female connector with a right angle adapter

Diagnostics
Diagnostics

Power Up Runtime
Dual Port Memory Check Executive Checksum
LAN Controller Check RAM Address/Data

52 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
140 CRA 932 00
35010574 12/2018

Chapter 6
140 CRA 932 00: Remote I/O (RIO) Drop Module (dual channel)

140 CRA 932 00: Remote I/O (RIO) Drop Module (dual
channel)

Purpose
This chapter contains information of the 140 CRA 932 00 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 54
Indicators 56
Error Codes 57
Specifications 58

35010574 12/2018 53
140 CRA 932 00

Presentation

Function
The Remote I/O Drop dual Channel modules are used to transfer data bi-directionally over a
coaxial cable network between I/O modules installed in the same (RIO drop) backplane and the
RIO head installed in the CPU backplane.

Illustration
The following figure shows the Remote I/O (RIO) module’s parts.

1 LED Area
2 RIO Coax Connector (Channel A)
3 RIO Coax Connector (Channel B)
4 Version Label
5 Model Number, Module Description, Color Code
6 Removable Door
7 Customer Identification Label (Fold label and place it inside door)

NOTE: To maintain CE compliance with the European Directive on EMC (89/336/EEC), the RIO
Head module must be connected using quad shielded cable (see the Remote I/O Cable System
Planning and Installation Guide).

54 35010574 12/2018
 140 CRA 932 00

Rear Panel Switches

Two rotary switches are located on the rear panel of the RIO Drop Modules and are used for setting
RIO drop addresses (refer to the illustration and table below).
SW1 (top switch) sets the upper digit (tens); SW2 (bottom switch) sets the lower digit (ones). The
illustration below shows the correct setting for an example address of 11.

Rear Panel Switches Figure

The following figure shows the SW1 top and SW2 bottom switches.

SW1 and SW2 Switches Table

The following table shows the node addresses of the SW1 and SW2 switches.

Node Address SW1 SW2

1 ... 9 0 1 ... 9
10 ... 19 1 0 ... 9
20 ... 29 2 0 ... 9
30 ... 32 3 0 ... 2

NOTE: Only addresses from 2 to 32 are valid

If "0" or an address greater than 32 is selected, the RIO module displays a flashing "Error A"- and
"Error B"- LED.
With address “1” you don’t have flashing “Error A”- and “Error B”- LED.

35010574 12/2018 55
140 CRA 932 00

Indicators

Illustration
The following figure shows the LED indicators for the Drop module:

Description
The following table shows the RIO Drop module LED descriptions:

LEDS Color Indication when On

Ready Green The module has passed power-up diagnostics.
Com Act Green The module is communicating on the RIO network (see the
following table for LED error codes).
Fault Red Unable to communicate with one or more I/O modules.
This LED appears also when CRA is in bad position.
Error A Red Communication error on Channel A.
Error B Red Communication error on Channel B.

56 35010574 12/2018
 140 CRA 932 00

Error Codes

Error Codes Table

Blinking Com Act LED error codes for the RIO Drop module table show the number of times the
Com Act LED on the RIO Drop module blinks for each type of error and the crash codes for each
(all codes are in hex).
The following table shows the blinking Com Act LED error codes for the RIO Drop module.

Number of Blinks Code Description of Error

3 6701H ASIC test failure
4 6601H power down interrupt
6602H 82588 lan chip test error
6603H receive abort timeout
6604H transmission loop timeout
6605H transmission DMA error
6606H cable a initialization error
6607H cable a DMA xfer error
6608H cable b DMA xfer error
6609H cable a dumped data error
660AH cable a DRQ line hung
660BH cable b DRQ line hung
660CH cable a or b DRQ hung
660DH power-up lan controller error
5 6501H RAM address test error
6 6401H RAM data test error
7 6301H PROM checksum error

35010574 12/2018 57
140 CRA 932 00

Specifications

General Specification
General Specification

Bus Current required 750 mA

Power Dissipation 3.8 W
(Typical)
I/O Type Quantum
Modules/Drop 14 max.
28 max. with Backplane expander (XBE)
Words/Drop 64 IN / 64 OUT
Holdup Time Software configurable

NOTE: You can specify a monitoring time of 3 - 65 535 in this text box. With communication
interruptions with the remote processor, the output modules will maintain their last operating
condition during that time. Once the monitoring time has expired, the output modules will reset to
their default timeout status. The monitoring time does not influence input modules. The CPU will
immediately set the input values to zero.

Connection / Transmission
Connection / Transmission

Coax Termination Internal 75 ohms

Coax Shield Capacitor to ground
Data Transfer Rate 1.544 Mb
Dynamic Range 35 dB
External Connections Two "F" type female connector with a right angle adapter

Diagnostics
Diagnostics

Power Up Runtime
Dual Port Memory Check Executive Checksum
LAN Controller Check RAM Address/Data

58 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
140 NRP 954 00
35010574 12/2018

Chapter 7
140 NRP 954 00: Fiber Optic Repeater Module (Multimode)

140 NRP 954 00: Fiber Optic Repeater Module (Multimode)

Purpose
This chapter contains information of the 140 NRP 954 00 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 60
LED Indicators and Diagnostic Relay Behavior 63
Module Connections 65
General Specifications 76

35010574 12/2018 59
140 NRP 954 00

Presentation

Function
The 140 NRP 954 00 fiber optical repeater module provides communication between two or more
RIO nodes or segments of networks over a multimode fiber optic medium. Each repeater contains
one electrical RIO interface and two fiber optic transceivers.

Illustration
The following figure shows the 140 NRP 954 00 (NRP) module parts.

1 Version label
2 Model number, module description, color code
3 LED area
4 Removable door
5 Customer identification label (Fold label and place it inside door)
6 Diagnostic relay port
7 Electrical coaxial port (“F” type connector)
8 Transmitter optical fiber port - FPort 1 Tx (ST type connector)
9 Receiver optical fiber port - FPort 1 Rx (ST type connector)
10 Receiver optical fiber port - FPort 2 Rx (ST type connector)
11 Transmitter optical fiber port - FPort 2 Tx (ST type connector)

60 35010574 12/2018
 140 NRP 954 00

Diagnostic Relay Port

A normally closed relay contact, rated at 220 Vac 6 A or 30 Vdc 5 A, is available on the terminals
of the diagnostic relay port via its connector. This allows to use the diagnostic relay behavior
(see page 64) in the application.
The following figure shows the 2 terminals of the diagnostic relay connector:

Electrical Coaxial Port

The 140 NRP 954 00 fiber optic repeater module is equipped with an electrical coaxial RIO
interface using an "F"-style connector. In order to maintain bend radius tolerance on coaxial cable
the electrical coaxial port is equipped with a right-angle F adapter.
The electrical coaxial port has the same network connections, specifications and restrictions as
other remote I/O devices, and must be treated accordingly. See the Remote I/O Cable System
Planning and Installation Guide for information regarding planning your network configuration as
well as the installation of the network electrical coaxial cable.

CAUTION
CONNECTIVITY COMPLIANCE
To maintain CE compliance with the European Directive on EMC (89/336/EEC), the
140 NRP 954 00 module must be connected using quad shielded cable (see the Remote I/O
Cable System Planning and Installation Guide).
Failure to follow these instructions can result in injury or equipment damage.

35010574 12/2018 61
140 NRP 954 00

Optical Ports
The 140 NRP 954 00 fiber optic repeater module is equipped with two optical ports (FPort1 and
FPort2). One pair of fiber optic cables are connected to one fiber optic port using two low-loss
industrial ST-type connectors (one for the transmitter signal (Tx) and one for the receiver signal
(Rx)).

62 35010574 12/2018
 140 NRP 954 00

LED Indicators and Diagnostic Relay Behavior

Illustration
The following figure shows the LED indicators for the 140 NRP 954 00 fiber optic repeater module:

LED Indicators
The following table describes the status LEDs of the 140 NRP 954 00 module:

LED Color State Indication

Ready Green OFF The module is unpowered or the internal logic is out of order.
ON The module is powered and the internal logic is available.
ComAct Green OFF No activity on the coaxial cable.
ON Activity is detected on the coaxial cable.
FPort1 Green OFF No activity on the optical fiber port 1 reception.
ON Activity is detected on the fiber port 1 reception.
FPort2 Green OFF No activity on the optical fiber port 2 reception.
ON Activity is detected on the fiber port 2 reception.
Fault Red OFF No error (internal or external) detected.
ON An error (internal or external) has been detected.
Error Red OFF No internal error detected.
ON An internal error has been detected.
BrkF Red OFF Activity is detected on both optical port inputs OR no activity
has ever been detected on any optical port input.
ON One of the optical fiber port input is inactive (see FPort• LED
OFF) while activity is detected or has been detected on the
other optical port input (see FPort• LED ON).

35010574 12/2018 63
140 NRP 954 00

Diagnostic Relay Behavior

The contacts of the relay are open whenever an error is detected (internal or external), and the
Fault LED is ON. In fact the status of the diagnostic relay provides an electric information when the
Fault LED status provides a visual status when an error is detected (internal or external).
Futhermore when the contacts of the diagnostic relay are open,
 if the detected error is internal the Error LED is ON.
 if the detected error is external the BrkF LED is ON.

NOTE: When the 140 NRP 954 00 is not powered, the contacts of the diagnostic relay are open.

64 35010574 12/2018
 140 NRP 954 00

Module Connections

Using Fiber Optics in a RIO System

The following represent four typical configurations that show the wide range of the network
architecture:
 Point-to-Point topology
 Bus topology
 Tree topology
 Self Healing Ring topology

35010574 12/2018 65
140 NRP 954 00

Point-to-Point Topology with Fiber Optic Repeater

Point-to-point configuration (see the following figure) allows communication over the distance of up
to 3 km through harsh industrial environments. The following figure shows the point-to-point
configuration.

NOTE:
 Using 2 optical fiber pairs provides a better service and diagnostics.
 Using only one fiber pair, looping back the unused optical ports with a short fiber helps using the
diagnostics.
For more details on the diagnostics, refer to the Modicon 140 NRP 954 00 and 140 NRP 954 01C
Fiber Optic Repeater Modules User Guide.

66 35010574 12/2018
 140 NRP 954 00

Bus Topology with Fiber Optic Repeater

This type of configuration is used when it is required to increase the length of the fiber link and
increase the distance between drops on the RIO network.

CAUTION
EQUIPMENT FAILURE
The loss of a single fiber optic repeater in this configuration disables the rest of the network. It is
suggested that the Self Healing Ring configuration be used to avoid this problem.
Failure to follow these instructions can result in injury or equipment damage.

35010574 12/2018 67
140 NRP 954 00

The following figure shows the bus topology:

NOTE: The distance between nodes on fiber is limited by the maximum allowable power loss from
end-to-end (3 km over 62.5 µm fiber). Power loss includes the fiber optic cable attenuation,
connector losses at the fiber optic receiver and transmitter ports, and the system margin of 3 dB.
NOTE: At each end of the bus, looping back the unused optical ports with a short fiber helps using
the diagnostics. For more details on the diagnostics, refer to the Modicon 140 NRP 954 00 and
140 NRP 954 01C Fiber Optic Repeater Modules User Guide.

68 35010574 12/2018
 140 NRP 954 00

Tree Topology with Fiber Optic Repeater

Tree topologies, which cannot be established with coaxial cable alone can be built legally using
fiber optic repeaters.
NOTE: The limitations (see page 76) in bus and self-healing configurations are applicable for each
drop in tree topology.
The following illustration shows an example of a tree topology:

NOTE:
 Using 2 optical fiber pairs provides a better service and diagnostics.
 Using only one fiber pair, looping back the unused optical ports with a short fiber helps using the
diagnostics.
For more details on the diagnostics, refer to the Modicon 140 NRP 954 00 and 140 NRP 954 01C
Fiber Optic Repeater Modules User Guide.

35010574 12/2018 69
140 NRP 954 00

Self-Healing Ring Topology with Fiber Optic Repeater

This configuration can be achieved by connecting the unused fiber optic ports of the first and last
140 NRP 954 00 directly or through the fiber optic repeater. This type of connection has all the
advantages of the previously described configurations, along with built-in redundancy. A broken
connection between any two Quantum NRP modules in the ring will automatically reconfigure the
RIO network and continue the communication.
NOTE: The maximum length of the fiber cable in a ring configuration, 16 km, is calculated in the
the case of a break that occurs anywhere.

70 35010574 12/2018
 140 NRP 954 00

Hot Standby Systems with Fiber Optic Repeater

The following figure shows an example of hot standby systems using fiber optic repeaters:

NOTE:
 Using 2 optical fiber pairs provides a better service and diagnostics.
 Using only one fiber pair, looping back the unused optical ports with a short fiber helps using the
diagnostics.
For more details on the diagnostics, refer to the Modicon 140 NRP 954 00 and 140 NRP 954 01C
Fiber Optic Repeater Modules User Guide.

35010574 12/2018 71
140 NRP 954 00

Backplane Integration
Instead of placing each fiber optic repeater modules with its own power supply module(s) in a
standalone backplane, you can take the advantage of the quantum form factor.
The following figure shows two segments of RIO coaxial cable connected point-to-point by two
140 NRP 954 00 fiber optic repeaters placed on the Quantum racks where the RIO head and RIO
drop modules are located:

NOTE:
 Using 2 optical fiber pairs provides a better service and diagnostics.
 Using only one fiber pair, looping back the unused optical ports with a short fiber helps using the
diagnostics.
For more details on the diagnostics, refer to the Modicon 140 NRP 954 00 and 140 NRP 954 01C
Fiber Optic Repeater Modules User Guide.

Recommended Materials for Fiber Optic Links

Modicon does not manufacture fiber optic products such as cables, connectors, or special tools.
However, we have experience with third party suppliers of materials and can give some guidelines
on what will work with our products.

72 35010574 12/2018
 140 NRP 954 00

Connectors
The following table shows the connector types

Connector Type Part Number Operating Temperature

ST Bayonet (Epoxy) 3M 6105 –40...+80 °C (–40...+176 °F)
ST Bayonet (Hot Melt) 3M 6100 –40...+80 °C (–40...+176 °F)
ST Bayonet (Epoxy) AMP 501380 Series –30...+70 °C (–22...+158 °F)
ST Cleave and Crimp AMP 504034 Series –40...+65 °C (–40...+149 °F)
Mechanical Line Splice (one 3M 2529 Fiberlok™ II –40...+80 °C (–40...+176 °F)
size fits all)

NOTE: All connectors must have a short boot for strain relief.

Termination Kits
The following table shows the termination kits.

Kit Type Part Number Description

Bayonet or Push-Pull ST (Hot 3M 6355 110 Vac, only for 3M connectors
Melt)
Bayonet ST (Epoxy) AMP 501258-7 110 Vac, only for AMP connectors
Bayonet ST (Epoxy) AMP 501258-8 220 Vac, only for AMP connectors
Mechanical Line Splice 3M 2530 Fiber Splice Prep Kit, complete with
cleaving tool

Light Sources, Power Meters

For Photodyne light sources and power meter products, contact 3M Telecom Systems Division.

35010574 12/2018 73
140 NRP 954 00

Observing Safety Precautions

Before installing the 140 NRP 954 00 fiber optic repeater module, read the warning messages
below. Follow them at all times during the installation of the fiber optic repeater.

DANGER
SEVERE EYE DAMAGE
Do not view the ends of fiber optic cable under magnification while a transmit signal is present on
the cable.
Failure to follow these instructions will result in death or serious injury.

NOTICE
INOPERABLE EQUIPMENT
Do not remove the protective coverings from the optical cable port and optical cable tips until
immediately fiber cable connection to the cable port.
After removing the protective coverings, never touch exposed parts such as the ferrule.
After connecting the fiber cable, retain the protective coverings for future use.
Do not remove the protective covering from the unused connector.
Failure to follow these instructions can result in equipment damage.

Before Starting
Prior to installing 140 NRP 954 00 fiber optic repeater, network cables must be prepared and
installed to the repeater’s site with their connectors.
To prepare optic cables:
 Follow the cable manufacturer’s recommendations for routing, installing, and testing the cable.
Take care when terminating the ends of each fiber optic cable in order to minimize loss of optical
signal. Follow the manufacturer’s guidelines for installing optical connectors.
 Test the cable for proper attenuation prior to the connection of the fiber optic repeaters. The
cable ends should be accessible at each fiber optic installation site. Allow sufficient cable length
for a service loop and strain reliefs.
 Label each cable end to facilitate future maintenance.

To prepare and install coaxial cables, refer to Remote I/O Cable System Planning and Installation
Guide.

74 35010574 12/2018
 140 NRP 954 00

Connecting the Fiber Optic Cable

The following steps show how to connect the fiber optic cable.

Step Action
1 Remove the protective plastic coverings from the cable ports and the tips of the
cable. Snap one of the fiber cable clasps (shipped with the module) over the
cable so that the wider end of the tool is closest to the cable end.

2 Turn the connection ring so that one of the arrows on the side of the ring lines up
with the ridge inside.

3 a. Slide the tool up to the connection ring.

b. Gripping the cable with the plastic cable clasp, slide the cable end onto the
lower cable port. The arrow and the ridge on the connection ring should lineup
with the slot on the left of the cable port.
c. Use the clasp to push the cable over the tab on top of the port.
d. Turn the cable to the right, so that the tab locks securely
e. Remove the clasp.
f. Repeat this process with the remaining strand of cable.

35010574 12/2018 75
140 NRP 954 00

General Specifications

Introduction
This section gives the 140 NRP 954 00 fiber optic repeater module specifications.

WARNING
UNINTENDED EQUIPMENT OPERATION
Do not exceed any of the rated values specified in the following tables.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

General Specifications

Bus Current Required 700 mA

Power Dissipation (Typical) 5W
Inrush Current 1 A typical @ 5 Vdc
Data Transfer Rate 1.544 Mb for remote I/O with Manchester encoded data
Bit Error Rate 10-9 over specified Optical Receiver Dynamic Range
Optical Interface ST-Type connector
Wavelength 820 nm
Power Loss Budget 50/125 µm fiber –7.0 dB
(includes 3 dB of system 62.5/125 µm fiber –11 dB
margin) 100/140 µm fiber –16.5 dB
Maximum Distance for Point– 2 km over 50/125 µm fiber @ 3.5 dB/km
to–Point Connection 3 km over 62.5/125 µm fiber @ 3.5 dB/km
3 km over 100/140 µm fiber @ 5 dB/km
Limits in Bus or Self-Healing 12 fiber optic repeater modules with a maximum length of fiber optic
Ring Configurations cables of 16 km (back-loop included in Self-healing ring configuration).
NOTE: The maximum length is between the CRP module (the farther
one in a Hot Standby (HSBY) system) and the last CRA module.
Coaxial Interface F type female connector with a right-angle F adapter connector
NOTE: Required torque to fasten the right-angle F adapter is
0.46...0.60 N•m (4.1...5.3 lbf-in).
Coaxial Termination Internal 75 ohms
Coaxial Shield Tied to ground
Coaxial Dynamic Range 35 dB
Coaxial Sensitivity 70 mV pk-pk max
Relay Diagnostic Rated at 220 Vac 6 A / 30 Vdc 5 A

76 35010574 12/2018
 140 NRP 954 00

NOTICE
DESTRUCTION OF ADAPTER
 Before tightening the locknut to the torque 0.46...0.60 N•m (4.1...5.3 lbf-in) be sure to properly
position the right-angle F adapter connector.
 During tightening be sure to maintain the connector securely.
 The locknut must be loosened before handling the connector. For this reason, it is
recommended to attach the S908 coaxial cable to the chassis to avoid any mechanical stress
on the right-angle F adapter connector.
 Do not tighten the right-angle F adapter beyond the specified torque.
Failure to follow these instructions can result in equipment damage.

Optical Transmitter Specifications

Optical Power (Measured with –13.0...–20.0 dBm average power in 50/125 µm fiber cable
1 m test fiber) –10.0...–16 dBm average power in 62.5/125 µm fiber cable
–4.0...–10.5 dBm average power in 100/140 µm fiber cable
Rise/Fall Time 20 nsec or better
Silence (OFF Leakage) –43 dBm

Optical Receiver Specifications

Receiver Sensitivity –30 dBm average power

Dynamic Range 20 dB
Detected Silence –36 dBm

Reliability

MTBF 1,300,000 hours (minimum) @ 30 °C, assuming fixed

ground and component stress within maximum
specifications.

35010574 12/2018 77
140 NRP 954 00

78 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
140 NRP 954 01C
35010574 12/2018

Chapter 8
140 NRP 954 01C: Fiber Optic Repeater Module (Single-mode)

140 NRP 954 01C: Fiber Optic Repeater Module (Single-

mode)

Purpose
This chapter contains information of the 140 NRP 954 01C Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 80
LED Indicators and Diagnostic Relay Behavior 83
Module Connections 85
General Specifications 96

35010574 12/2018 79
140 NRP 954 01C

Presentation

Function
The 140 NRP 954 01C fiber optical repeater module provides communication between two or
more RIO nodes or segments of networks over a single-mode fiber optic medium. Each repeater
contains one electrical RIO interface and two fiber optic transceivers.

Illustration
The following figure shows the 140 NRP 954 01C (NRP) module parts.

1 Version label
2 Model number, module description, color code
3 LED area
4 Removable door
5 Customer identification label (Fold label and place it inside door)
6 Diagnostic relay port
7 Electrical coaxial port (“F” type connector)
8 Receiver optical fiber port - FPort 1 Rx (LC type connector)
9 Transmitter optical fiber port - FPort 1 Tx (LC type connector)
10 Receiver optical fiber port - FPort 2 Rx (LC type connector)
11 Transmitter optical fiber port - FPort 2 Tx (LC type connector)

80 35010574 12/2018
 140 NRP 954 01C

Diagnostic Relay Port

A normally closed relay contact, rated at 220 Vac 6 A or 30 Vdc 5 A, is available on the terminals
of the diagnostic relay port via its connector. This allows to use the diagnostic relay behavior
(see page 64) in the application.
The following figure shows the 2 terminals of the diagnostic relay connector:

Electrical Coaxial Port

The 140 NRP 954 01C fiber optic repeater module is equipped with an electrical coaxial RIO
interface using an "F"-style connector. In order to maintain bend radius tolerance on coaxial cable
the electrical coaxial port is equipped with a right-angle F adapter.
The electrical coaxial port has the same network connections, specifications and restrictions as
other remote I/O devices, and must be treated accordingly. See the Remote I/O Cable System
Planning and Installation Guide for information regarding planning your network configuration as
well as the installation of the network electrical coaxial cable.

CAUTION
CONNECTIVITY COMPLIANCE
To maintain CE compliance with the European Directive on EMC (89/336/EEC), the
140 NRP 954 01C module must be connected using quad shielded cable (see the Remote I/O
Cable System Planning and Installation Guide).
Failure to follow these instructions can result in injury or equipment damage.

35010574 12/2018 81
140 NRP 954 01C

Optical Ports
The 140 NRP 954 01C fiber optic repeater module is equipped with two optical ports (FPort1 and
FPort2). One pair of fiber optic cables are connected to one fiber optic port using a duplex LC-type
connector.

82 35010574 12/2018
 140 NRP 954 01C

LED Indicators and Diagnostic Relay Behavior

Illustration
The following figure shows the LED indicators for the 140 NRP 954 01C fiber optic repeater
module:

LED Indicators
The following table describes the status LEDs of the 140 NRP 954 01C module:

LED Color State Indication

Ready Green OFF The module is unpowered or the internal logic is out of order.
ON The module is powered and the internal logic is available.
ComAct Green OFF No activity on the coaxial cable.
ON Activity is detected on the coaxial cable.
FPort1 Green OFF No activity on the optical fiber port 1 reception.
ON Activity is detected on the fiber port 1 reception.
FPort2 Green OFF No activity on the optical fiber port 2 reception.
ON Activity is detected on the fiber port 2 reception.
Fault Red OFF No error (internal or external) detected.
ON An error (internal or external) has been detected.
Error Red OFF No internal error detected.
ON An internal error has been detected.
BrkF Red OFF Activity is detected on both optical port inputs OR no activity
has ever been detected on any optical port input.
ON One of the optical fiber port input is inactive (see FPort• LED
OFF) while activity is detected or has been detected on the
other optical port input (see FPort• LED ON).

35010574 12/2018 83
140 NRP 954 01C

Diagnostic Relay Behavior

The contacts of the relay are open whenever an error is detected (internal or external), and the
Fault LED is ON. In fact the status of the diagnostic relay provides an electric information when the
Fault LED status provides a visual status when an error is detected (internal or external).
Futhermore when the contacts of the diagnostic relay are open,
 if the detected error is internal the Error LED is ON.
 if the detected error is external the BrkF LED is ON.

NOTE: When the 140 NRP 954 01C is not powered, the contacts of the diagnostic relay are open.

84 35010574 12/2018
 140 NRP 954 01C

Module Connections

Using Fiber Optics in a RIO System

The following represent four typical configurations that show the wide range of the network
architecture:
 Point-to-Point topology
 Bus topology
 Tree topology
 Self Healing Ring topology

35010574 12/2018 85
140 NRP 954 01C

Point-to-Point Topology with Fiber Optic Repeater

Point-to-point configuration (see the following figure) allows communication over the distance of up
to 16 km through harsh industrial environments. The following figure shows the point-to-point
configuration.

NOTE:
 Using 2 optical fiber pairs provides a better service and diagnostics.
 Using only one fiber pair, looping back the unused optical ports with a short fiber helps using the
diagnostics.
For more details on the diagnostics, refer to the Modicon 140 NRP 954 00 and 140 NRP 954 01C
Fiber Optic Repeater Modules User Guide.

86 35010574 12/2018
 140 NRP 954 01C

Bus Topology with Fiber Optic Repeater

This type of configuration is used when it is required to increase the length of the fiber link and
increase the distance between drops on the RIO network.

CAUTION
EQUIPMENT FAILURE
The loss of a single fiber optic repeater in this configuration disables the rest of the network. It is
suggested that the Self Healing Ring configuration be used to avoid this problem.
Failure to follow these instructions can result in injury or equipment damage.

The following figure shows the bus topology:

35010574 12/2018 87
140 NRP 954 01C

NOTE: The total distance between the first and the last fiber optic repeater is limited by the
maximum allowable power loss from end-to-end (16 km over 9/125 µm fiber). Power loss includes
the fiber optic cable attenuation, connector losses at the fiber optic receiver and transmitter ports,
and the system margin of 3 dB.
NOTE: At each end of the bus, looping back the unused optical ports with a short fiber helps using
the diagnostics. For more details on the diagnostics, refer to the Modicon 140 NRP 954 00 and
140 NRP 954 01C Fiber Optic Repeater Modules User Guide.

88 35010574 12/2018
 140 NRP 954 01C

Tree Topology with Fiber Optic Repeater

Tree topologies, which cannot be established with coaxial cable alone can be built legally using
fiber optic repeaters.
NOTE: The limitations (see page 96) in bus and self-healing configurations are applicable for each
drop in tree topology.
The following illustration shows an example of a tree topology:

NOTE:
 Using 2 optical fiber pairs provides a better service and diagnostics.
 Using only one fiber pair, looping back the unused optical ports with a short fiber helps using the
diagnostics.
For more details on the diagnostics, refer to the Modicon 140 NRP 954 00 and 140 NRP 954 01C
Fiber Optic Repeater Modules User Guide.

35010574 12/2018 89
140 NRP 954 01C

Self-Healing Ring Topology with Fiber Optic Repeater

This configuration can be achieved by connecting the unused fiber optic ports of the first and last
140 NRP 954 01C directly or through the fiber optic repeater. This type of connection has all the
advantages of the previously described configurations, along with built-in redundancy. A broken
connection between any two Quantum NRP modules in the ring will automatically reconfigure the
RIO network and continue the communication.
NOTE: The maximum length of the fiber cable in a ring configuration, 16 km, is calculated in the
the case of a break that occurs anywhere (back-loop included).

90 35010574 12/2018
 140 NRP 954 01C

Hot Standby Systems with Fiber Optic Repeater

The following figure shows an example of hot standby systems using fiber optic repeaters:

NOTE:
 Using 2 optical fiber pairs provides a better service and diagnostics.
 Using only one fiber pair, looping back the unused optical ports with a short fiber helps using the
diagnostics.
For more details on the diagnostics, refer to the Modicon 140 NRP 954 00 and 140 NRP 954 01C
Fiber Optic Repeater Modules User Guide.

35010574 12/2018 91
140 NRP 954 01C

Backplane Integration
Instead of placing each fiber optic repeater modules with its own power supply module(s) in a
standalone backplane, you can take the advantage of the quantum form factor.
The following figure shows two segments of RIO coaxial cable connected point-to-point by two
140 NRP 954 01C fiber optic repeaters placed on the Quantum racks where the RIO head and RIO
drop modules are located:

NOTE:
 Using 2 optical fiber pairs provides a better service and diagnostics.
 Using only one fiber pair, looping back the unused optical ports with a short fiber helps using the
diagnostics.
For more details on the diagnostics, refer to the Modicon 140 NRP 954 00 and 140 NRP 954 01C
Fiber Optic Repeater Modules User Guide.

Recommended Materials for Fiber Optic Links

Modicon does not manufacture fiber optic products such as cables, connectors, or special tools.
However, we have experience with third party suppliers of materials and can give some guidelines
on what will work with our products.

92 35010574 12/2018
 140 NRP 954 01C

Observing Safety Precautions

Before installing the 140 NRP 954 01C fiber optic repeater module, read the warning messages
below. Follow them at all times during the installation of the fiber optic repeater.

DANGER
SEVERE EYE DAMAGE
Do not view the ends of fiber optic cable under magnification while a transmit signal is present on
the cable.
Failure to follow these instructions will result in death or serious injury.

NOTICE
INOPERABLE EQUIPMENT
Do not remove the protective coverings from the optical cable port and optical cable tips until
immediately fiber cable connection to the cable port.
After removing the protective coverings, never touch exposed parts such as the ferrule.
After connecting the fiber cable, retain the protective coverings for future use.
Do not remove the protective covering from the unused connector.
Failure to follow these instructions can result in equipment damage.

Before Starting
Prior to installing 140 NRP 954 01C fiber optic repeater, network cables must be prepared and
installed to the repeater’s site with their connectors.
To prepare optic cables:
 Follow the cable manufacturer’s recommendations for routing, installing, and testing the cable.
Take care when terminating the ends of each fiber optic cable in order to minimize loss of optical
signal. Follow the manufacturer’s guidelines for installing optical connectors.
 Test the cable for proper attenuation prior to the connection of the fiber optic repeaters. The
cable ends should be accessible at each fiber optic installation site. Allow sufficient cable length
for a service loop and strain reliefs.
 Label each cable end to facilitate future maintenance.

To prepare and install coaxial cables, refer to Remote I/O Cable System Planning and Installation
Guide.

35010574 12/2018 93
140 NRP 954 01C

Connecting the Fiber Optic Cable

Install the fiber optic cable to the 140 NRP 954 01C module’s LC duplex connectors as described
in the following table:

Step Action
1 Remove the dust plugs from the LC connectors of the fiber optic cable as shown in
the following figure. Save the dust plugs for future use.

2 Inspect and clean the fiber optic end faces of the LC connectors.
3 Remove the dust plugs from the LC duplex connector as shown in the following
figure:

4 Immediately attach the fiber optic cable to the LC duplex connector of the module
as shown in the following figure:

94 35010574 12/2018
 140 NRP 954 01C

Compatibility Rules
Depending on the PV (Product Version) and SV (Software Version) of the CRA modules, the
140 NRP 954 01C may be incompatible.
The following table gives the compatibility rules between the 140 NRP 954 01C and CRA modules:

CRA Module PV SV Compatibility

Reference Communication Remote OS Update via S908 Bus
140 CRA 93• 00 ≤ 08 2.0 Yes Yes
09 2.0 No(1)
No(2)
≥ 10 2.01 Yes No(2)
PV Product version
SV Software version

(1)
An upgrade of the SV to 2.01 makes the module communication compatible.
NOTE: Upgrading the software version of the CRA module from 2.0 to 2.01 for CRA
modules PV 09 is mandatory before using 140 NRP 954 01C in the RIO network.
(2)
For CRA module with SV ≥2.0, OS update is only possible out of the RIO network.

The 140 CRA 93• 00 firmware upgrade is done through Modbus or Modbus Plus using the Control
Expert OS loader tool. The procedure to follow is described in the Quantum Operating System
Upgrade and Update Procedure.

35010574 12/2018 95
140 NRP 954 01C

General Specifications

Introduction
This section gives the 140 NRP 954 01C fiber optic repeater module specifications.

WARNING
UNINTENDED EQUIPMENT OPERATION
Do not exceed any of the rated values specified in the following tables.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

General Specifications

Bus Current Required 750 mA

Power Dissipation (Typical) 5W
Inrush Current 1.8 A typical @ 5 Vdc
Data Transfer Rate 1.544 Mb for remote I/O with Manchester encoded data
Bit Error Rate 10-9 over specified Optical Receiver Dynamic Range
Optical Interface LC-Type connector
Wavelength 1300 nm
Power Loss Budget 9/125 µm fiber –8.0 dB
(includes 3 dB of system
margin)
Maximum Distance for Point– 16 km over 9/125 µm fiber @ 0.45 dB/km
to–Point Connection
Limits in Bus or Self-Healing 12 fiber optic repeater modules with a maximum length of fiber optic
Ring Configurations cables of 16 km (back-loop included in Self-healing ring configuration).
NOTE: The maximum length is between the CRP module (the farther
one in a Hot Standby (HSBY) system) and the last CRA module.
Coaxial Interface F type female connector with a right-angle F adapter connector
NOTE: Required torque to fasten the right-angle F adapter is
0.46...0.60 N•m (4.1...5.3 lbf-in).
Coaxial Termination Internal 75 ohms
Coaxial Shield Tied to ground
Coaxial Dynamic Range 35 dB
Coaxial Sensitivity 70 mV pk-pk max
Relay Diagnostic Rated at 220 Vac 6 A / 30 Vdc 5 A

96 35010574 12/2018
 140 NRP 954 01C

NOTICE
DESTRUCTION OF ADAPTER
 Before tightening the locknut to the torque 0.46...0.60 N•m (4.1...5.3 lbf-in) be sure to properly
position the right-angle F adapter connector.
 During tightening be sure to maintain the connector securely.
 The locknut must be loosened before handling the connector. For this reason, it is
recommended to attach the S908 coaxial cable to the chassis to avoid any mechanical stress
on the right-angle F adapter connector.
 Do not tighten the right-angle F adapter beyond the specified torque.
Failure to follow these instructions can result in equipment damage.

Optical Transmitter Specifications

Optical Power (Measured with –8.0...–15.0 dBm average power in 9/125 µm fiber cable
1 m test fiber)
Rise/Fall Time 20 nsec or better
Silence (OFF Leakage) –45 dBm

Optical Receiver Specifications

Receiver Sensitivity –25 dBm average power

Dynamic Range 20 dB
Detected Silence –45 dBm

Reliability

MTBF 1,300,000 hours (minimum) @ 30 °C, assuming fixed

ground and component stress within maximum
specifications.

35010574 12/2018 97
140 NRP 954 01C

98 35010574 12/2018
 Quantum using EcoStruxure™ Control Expert
DIO Drop Modules
35010574 12/2018

Part III
Quantum Distributed I/O (DIO) Drop Modules

Quantum Distributed I/O (DIO) Drop Modules

Introduction
This part provides information on the following Quantum DIO modules:

DIO Module Source Voltage Communication Bus Current

Channels Required
140 CRA 211 10 115/230 VAC 1 3A
140 CRA 212 10 115/230 VAC 2 3A
140 CRA 211 20 24 VDC 1 3A
140 CRA 212 20 24 VDC 2 3A

Quantum DIO is implemented over a Modbus Plus network. The CPU or NOM modules may be
the network head via their Modbus Plus ports. Quantum DIO Modbus Plus drop adaptors are
specifically designed to link Quantum I/O modules to the head via twisted pair shielded cable
(Modbus Plus). The DIO drop modules also provide the I/O with power (maximum 3A) from a 24
VDC or a 115/230 VAC source. Each DIO network supports up to 63 distributed drops using
repeaters.
NOTE: In the DIO rack with 140 CRA 211 x0 module, 140 DSI 353 00 module must not be used.

What Is in This Part?

This part contains the following chapters:
Chapter Chapter Name Page
9 Software Configuration 101
10 140 CRA 211 10: DIO Drop Module 115/230 VAC (single channel) 105
11 140 CRA 212 10: DIO Drop Module 115/230 VAC (dual channel) 113
12 140 CRA 211 20: DIO Drop Module 24 VDC (single channel) 121
13 140 CRA 212 20: DIO Drop Module 24 VDC (dual channel) 129

35010574 12/2018 99
DIO Drop Modules

100 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
Software Configuration
35010574 12/2018

Chapter 9
Software Configuration

Software Configuration

Configuring a Quantum DIO Drop

Introduction
A Quantum DIO Drop consists of a standard module rack installed with I/O modules and a
140 CRA 21• •0 Modbus Plus communication module.
A DIO Bus can either be connected to the Modbus Plus connection on the CPU, or to a
140 NOM 2•• 00 communication module.
NOTE: The Quantum DIO Drop Modules 140 CRA 2•• ••• have no health bits.
For this reason the status for a properly functioning DIO Drop is always ZERO and not ONE as it
is for other modules!

Adding a DIO Bus

The following table describes the procedure for adding a DIO Bus.

Step Action
1 Select the Modbus Plus connection that you want to configure as a DIO Bus from
the Project Browser or in the hardware configuration window.
The following configuration window is opened:

35010574 12/2018 101

Software Configuration

Step Action
2 Activate the DIO Bus check box in the configuration window and confirm your
entry.
A DIO Bus is placed in the Project Browser:

3 Open the DIO Bus and select add module rack and select New Device.
The module rack selection list is opened:

102 35010574 12/2018

 Software Configuration

Step Action
4 Select the desired module rack and enter the Modbus Plus address in the
address field. Confirm with OK.
A DIO Drop is placed in the Project Browser. The number set, 12 in our example,
states the Modbus Plus address of the Drop. The Modbus Plus Coupler
140 CRA 21X X0 is automatically entered in slot 1:

5 To continue configuring the RIO Drop you can carry on as with configuring a local
I/O.

Modbus Plus Address

Ensure that the Modbus Plus Station Address that you have entered in the software configuration
matches the hardware addresses of the modules used.

35010574 12/2018 103

Software Configuration

104 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 CRA 211 10
35010574 12/2018

Chapter 10
140 CRA 211 10: DIO Drop Module 115/230 VAC (single channel)

140 CRA 211 10: DIO Drop Module 115/230 VAC (single
channel)

Purpose
This chapter contains information of the 140 CRA 211 10 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 106
Indicators 108
Specifications 109
Wiring Diagram 111

35010574 12/2018 105

140 CRA 211 10

Presentation

Function
The 140 CRA 211 10 is a single channel Distributed I/O Interface, connected via a twisted pair
Modbus Plus cable network. This DIO Drop Module provides the I/O with power from a 115/230
VAC source.

Illustration
The following figure shows the parts of the distributed I/O (DIO) module.

Rear Panel Switches

Two rotary switches (refer to the illustration and table below) are located on the rear panel of the
CPU. They are used for setting Modbus Plus node addresses for the unit.
SW1 (the top switch) sets the upper digit (tens) of the address; SW2 (the bottom switch) sets the
lower digit (ones) of the address. The illustration below shows the correct setting for an example
address of 11.

106 35010574 12/2018

 140 CRA 211 10

Rear Panel Switches Figure

The following figure shows the SW1 top switch and the SW2 bottom switch.

Rear Panel Switches Table

The following table shows node addresses for the SW1 and SW2 switches.

Node Address SW1 SW2

1 ... 9 0 1 ... 9
10 ... 19 1 0 ... 9
20 ... 29 2 0 ... 9
30 ... 39 3 0 ... 9
40 ... 49 4 0 ... 9
50 ... 59 5 0 ... 9
60 ... 64 6 0 ... 4

NOTE: Only addresses from 1 to 64 are valid.

If "0" or an address greater than 64 is selected, the "Modbus+" LED comes ON, steady, indicating
that an invalid address was selected.

35010574 12/2018 107

140 CRA 211 10

Indicators

Illustration
The following figure shows the LED panel.

Description
The following table shows the DIO LED indicators and descriptions.

LEDS Color Indication when On

Ready Green The module has passed power-up diagnostics.
Fault Red A communications error exists between the DIO module and
one or more I/O modules, or an output module is not being
written to, over the Modbus Plus network.
Pwr ok Green Bus power is present.
Modbus + Green Communications are active on the Modbus Plus port.

108 35010574 12/2018

 140 CRA 211 10

Specifications

General Specifications
General Specifications

Operating Mode Standalone or not powered

Internal Power Dissipation 2.0 W + 3.0 V x IBUS (where IBUS is in Amperes)
Protection Over Current, Over Voltage
Communication 1 Modbus Plus port (single cable)
Field Wiring Connector 7 point terminal strip (Part # 043506326)
I/O Type Quantum
Modules/Drop Depends on bus current loading and word count
Words 30 IN / 32 OUT. (Two additional IN words are reserved for drop
status.)

Input
Input

Input Voltage 85 ... 276 VAC

Input Frequency 47 ... 63 Hz
Input Voltage Total Less than 10% of the fundamental rms value
Harmonic Distortion
Input Current 0.4 A @ 115 VAC. 0.2 A @ 230 VAC
Inrush Current 10 A @ 115 VAC. 20 A @ 230 VAC
VA Rating 50 VA
Input Power Interruption 1/2 cycle at full load and minimum rated line voltage / frequency.
No less than 1 second between interruptions.

Output to Bus
Output to Bus

Voltage 5.1 VDC

Current 3A
Minimum Load 0A
Fusing (external) 1.5 A (Part # 043502515 or equivalent)

35010574 12/2018 109

140 CRA 211 10

Diagnostics
Diagnostics

Power Up RAM
RAM Address
Executive Checksum
Runtime RAM
RAM Address
Executive Checksum

110 35010574 12/2018

 140 CRA 211 10

Wiring Diagram

Illustration
The following figure shows the wiring diagram for the 140 CRA 211 10

NOTE: Follow the Power and Grounding Guidelines of the Quantum Hardware Reference Manual
and the Grounding and Electromagnetic Compatibility of PLC Systems manual recommendations.

35010574 12/2018 111

140 CRA 211 10

112 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 CRA 212 10
35010574 12/2018

Chapter 11
140 CRA 212 10: DIO Drop Module 115/230 VAC (dual channel)

140 CRA 212 10: DIO Drop Module 115/230 VAC (dual
channel)

Purpose
This chapter contains information of the 140 CRA 212 10 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 114
Indicators 116
Specifications 117
Wiring Diagram 119

35010574 12/2018 113

140 CRA 212 10

Presentation

Function
The 140 CRA 212 10 is a dual channel Distributed I/O Interface, connected via a twisted pair
Modbus Plus cable network. This DIO Drop Module provides the I/O with power from a 115/230
VAC source.

Illustration
The following figure shows the parts of the distributed I/O (DIO) module.

Rear Panel Switches

Two rotary switches (refer to the illustration and table below) are located on the rear panel of the
CPU. Use them to set Modbus Plus node addresses for the unit.
SW1 (the top switch) sets the upper digit (tens) of the address; SW2 (the bottom switch) sets the
lower digit (ones) of the address. The illustration below shows the correct setting for the sample
address of 11.

114 35010574 12/2018

 140 CRA 212 10

Rear Panel Switches Figure

The following figure shows the SW1 top switch and the SW2 bottom switch.

Rear Panel Switches Table

The following table shows the node addresses of the SW1 and SW2 switches.

Node Address SW1 SW2

1 ... 9 0 1 ... 9
10 ... 19 1 0 ... 9
20 ... 29 2 0 ... 9
30 ... 39 3 0 ... 9
40 ... 49 4 0 ... 9
50 ... 59 5 0 ... 9
60 ... 64 6 0 ... 4

NOTE: Only addresses from 1 to 64 are valid.

If "0" or an address greater than 64 is selected, the "Modbus+" LED comes ON, steady, indicating
that an invalid address was selected.

35010574 12/2018 115

140 CRA 212 10

Indicators

Illustration
The following figure shows the LED panel.

Description
The following table shows the DIO LED indicators and descriptions.

LEDS Color Indication when On

Ready Green The module has passed power-up diagnostics.
Fault Red A communications error exists between the DIO module and
one or more I/O modules, or an output module is not being
written to, over the Modbus Plus network.
Pwr ok Green Bus power is present.
Modbus + Green Communications are active on the Modbus Plus port.
Error A Red Communication error on the Modbus Plus Channel A
Error B Red Communication error on the Modbus Plus Channel B

116 35010574 12/2018

 140 CRA 212 10

Specifications

General Specifications
General Specifications

Operating Mode Standalone or not powered

Internal Power Dissipation 2.0 W + 3.0 V x IBUS (where IBUS is in Amperes)
Protection Over Current, Over Voltage
Communication 2 Modbus Plus ports (dual cable)
Field Wiring Connector 7 point terminal strip (Part # 043506326)
I/O Type Quantum
Modules/Drop Depends on bus current loading and word count
Words 30 IN / 32 OUT. (Two additional IN words are reserved for drop
status.)

Input
Input

Input Voltage 85 ... 276 VAC

Input Frequency 47 ... 63 Hz
Input Voltage Total Less than 10% of the fundamental rms value
Harmonic Distortion
Input Current 0.4 A @ 115 VAC. 0.2 A @ 230 VAC
Inrush Current 10 A @ 115 VAC. 20 A @ 230 VAC
VA Rating 50 VA
Input Power Interruption 1/2 cycle at full load and minimum rated line voltage / frequency.
No less than 1 second between interruptions.

Output to Bus
Output to Bus

Voltage 5.1 VDC

Current 3A
Minimum Load 0A
Fusing (external) 1.5 A (Part # 043502515 or equivalent)

35010574 12/2018 117

140 CRA 212 10

Diagnostics
Diagnostics

Power Up RAM
RAM Address
Executive Checksum
Runtime RAM
RAM Address
Executive Checksum

118 35010574 12/2018

 140 CRA 212 10

Wiring Diagram

Illustration
The following figure shows the wiring diagram for the 140 CRA 212 10

NOTE: Follow the Power and Grounding Guidelines of the Quantum Hardware Reference Manual
and the Grounding and Electromagnetic Compatibility of PLC Systems manual recommendations.

35010574 12/2018 119

140 CRA 212 10

120 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 CRA 211 20
35010574 12/2018

Chapter 12
140 CRA 211 20: DIO Drop Module 24 VDC (single channel)

140 CRA 211 20: DIO Drop Module 24 VDC (single channel)

Purpose
This chapter contains information of the 140 CRA 211 20 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 122
Indicators 124
Specifications 125
Wiring Diagram 127

35010574 12/2018 121

140 CRA 211 20

Presentation

Function
The 140 CRA 211 20 is a single channel Distributed I/O Interface, connected via a twisted pair
Modbus Plus cable network. This DIO Drop Module provides the I/O with power from a 24 VDC
source.

Illustration
The following figure shows the parts of the distributed I/O (DIO) module.

Rear Panel Switches

Two rotary switches (refer to the illustration and table below) are located on the rear panel of the
CPU. They are used for setting Modbus Plus node addresses for the unit.
SW1 (the top switch) sets the upper digit (tens) of the address; SW2 (the bottom switch) sets the
lower digit (ones) of the address. The illustration below shows the correct setting for an example
address of 11.

122 35010574 12/2018

 140 CRA 211 20

Rear Panel Switches Figure

The following figure shows the SW1 top switch and the SW2 bottom switch.

Rear Panel Switches Table

The following table shows the node addresses of the SW1 and SW2 switches.

Node Address SW1 SW2

1 ... 9 0 1 ... 9
10 ... 19 1 0 ... 9
20 ... 29 2 0 ... 9
30 ... 39 3 0 ... 9
40 ... 49 4 0 ... 9
50 ... 59 5 0 ... 9
60 ... 64 6 0 ... 4

NOTE: Only addresses from 1 to 64 are valid.

If "0" or an address greater than 64 is selected, the "Modbus+" LED comes ON, steady, indicating
that an invalid address was selected.

35010574 12/2018 123

140 CRA 211 20

Indicators

Illustration
The following figure shows the LED panel.

Description
The following table shows the DIO LED indicators and descriptions.

LEDS Color Indication when On

Ready Green The module has passed power-up diagnostics.
Fault Red A communications error exists between the DIO module and
one or more I/O modules or an output module is not being
written to over the Modbus Plus network.
Pwr ok Green Bus power is present.
Modbus + Green Communications are active on the Modbus Plus port.

124 35010574 12/2018

 140 CRA 211 20

Specifications

General Specifications
General Specifications

Operating Mode Standalone

Internal Power Dissipation 2.0 W + 3.0 V x IBUS (where IBUS is in Amperes)
Protection Over Current, Over Voltage
Communication 1 Modbus Plus ports (single cable)
Field Wiring Connector 7 point terminal strip (Part # 043506326)
I/O Type Quantum
Modules/Drop Depends on bus current loading and word count
Words 30 IN / 32 OUT. (Two additional IN words are reserved for drop
status.)

Input
Input

Input Voltage 20 ... 30 VDC

Input Current 1.6 A
Inrush Current 30 A
Input Power Interruption 1.0 ms max.

Output to Bus
Output to Bus

Voltage 5.1 VDC

Current 3A
Minimum Load 0A
Fusing (external) 2.5 A (Part # 043502515 or equivalent)

35010574 12/2018 125

140 CRA 211 20

Diagnostics
Diagnostics

Power Up RAM
RAM Address
Executive Checksum
Runtime RAM
RAM Address
Executive Checksum

126 35010574 12/2018

 140 CRA 211 20

Wiring Diagram

Illustration
The following figure shows the wiring diagram for the 140 CRA 211 20 module

NOTE: Follow the Power and Grounding Guidelines of the Quantum Hardware Reference Manual
and the Grounding and Electromagnetic Compatibility of PLC Systems manual recommendations.

35010574 12/2018 127

140 CRA 211 20

128 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 CRA 212 20
35010574 12/2018

Chapter 13
140 CRA 212 20: DIO Drop Module 24 VDC (dual channel)

140 CRA 212 20: DIO Drop Module 24 VDC (dual channel)

Purpose
This chapter contains information of the 140 CRA 212 20 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 130
Indicators 132
Specifications 133
Wiring Diagram 135

35010574 12/2018 129

140 CRA 212 20

Presentation

Function
The 140 CRA 212 20 is a dual channel Distributed I/O Interface, connected via a twisted pair
Modbus Plus cable network. This DIO Drop Module provides the I/O with power from a 24 VDC
source.

Illustration
The following figure shows the parts of the distributed I/O (DIO) module.

1 LED Area
2 Modbus Plus Connector (Channel A)
3 Modbus Plus Connector (Channel B)
4 Field Wiring Connector
5 Field Wiring Connector Cover
6 Model Number, Module Description, Color Code
7 Removable Door
8 Customer Identification Label (Fold label and place it inside door)

130 35010574 12/2018

 140 CRA 212 20

Rear Panel Switches

Two rotary switches (refer to the illustration and table below) are located on the rear panel of the
CPU. They are used for setting Modbus Plus node addresses for the unit.
SW1 (the top switch) sets the upper digit (tens) of the address; SW2 (the bottom switch) sets the
lower digit (ones) of the address. The illustration below shows the correct setting for an example
address of 11.

Rear Panel Switches Figure

The following figure shows the SW1 top switch and the SW2 bottom switch.

Rear Panel Switches Table

The following table shows the node addresses of the SW1 and SW2 switches.

Node Address SW1 SW2

1 ... 9 0 1 ... 9
10 ... 19 1 0 ... 9
20 ... 29 2 0 ... 9
30 ... 39 3 0 ... 9
40 ... 49 4 0 ... 9
50 ... 59 5 0 ... 9
60 ... 64 6 0 ... 4

NOTE: Only addresses from 1 to 64 are valid.

If "0" or an address greater than 64 is selected, the "Modbus+" LED will be ON, steady, to indicate
the selection of an invalid address.

35010574 12/2018 131

140 CRA 212 20

Indicators

Illustration
The following figure shows the LED panel.

Description
The following table shows the DIO LED indicators and descriptions.

LEDS Color Indication when On

Ready Green The module has passed power-up diagnostics.
Fault Red A communications error exists between the DIO module and
one or more I/O modules or an output module is not being
written to over the Modbus Plus network.
Pwr ok Green Bus power is present.
Modbus + Green Communications are active on the Modbus Plus port.
Error A Red Communication error on the Modbus Plus Channel A
Error B Red Communication error on the Modbus Plus Channel B

132 35010574 12/2018

 140 CRA 212 20

Specifications

General Specifications
General Specifications

Operating Mode Standalone

Internal Power Dissipation 2.0 W + 3.0 V x IBUS (where IBUS is in Amperes)
Protection Over Current, Over Voltage
Communication 2 Modbus Plus ports (dual cable)
Field Wiring Connector 7 point terminal strip (Part # 043506326)
I/O Type Quantum
Modules/Drop Depends on bus current loading and word count
Words 30 IN / 32 OUT. (Two additional IN words are reserved for drop
status.)

Input
Input

Input Voltage 20 ... 30 VDC

Input Current 1.6 A
Inrush Current 30 A
Input Power Interruption 1.0 ms max.

Output to Bus
Output to Bus

Voltage 5.1 VDC

Current 3A
Minimum Load 0A
Fusing (external) 2.5 A (Part # 043502515 or equivalent)

35010574 12/2018 133

140 CRA 212 20

Diagnostics
Diagnostics

Power Up RAM
RAM Address
Executive Checksum
Runtime RAM
RAM Address
Executive Checksum

134 35010574 12/2018

 140 CRA 212 20

Wiring Diagram

Illustration
The following figure shows the wiring diagram for the 140 CRA 212 20 module

NOTE: Follow the Power and Grounding Guidelines of the Quantum Hardware Reference Manual
and the Grounding and Electromagnetic Compatibility of PLC Systems manual recommendations.

35010574 12/2018 135

140 CRA 212 20

136 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
NOM
35010574 12/2018

Part IV
Modbus Plus Network Option Modules (NOM)

Modbus Plus Network Option Modules (NOM)

Introduction
This part provides information on the following Quantum Network Option modules:

Module Communication Channels Bus Current

Required
140 NOM 211 00 1 Modbus (RS-232) serial port 780 mA
1 Modbus Plus network (RS-485) port
140 NOM 212 00 1 Modbus (RS-232) serial port 780 mA
2 Modbus Plus network (RS-485) ports
140 NOM 252 00 1 Modbus (RJ45) port 750 mA
2 Modbus Plus on fiber (consisting of optical
receiver and transmitter)

NOTE: More information is provided in the Modicon Modbus Plus Network, Planning and
Installation Guide (see page 13).

What Is in This Part?

This part contains the following chapters:
Chapter Chapter Name Page
14 140 NOM 211 00: Modbus Plus Option Module 139
15 140 NOM 212 00: Modbus Plus Option Module 151
16 140 NOM 252 00: Modbus Plus Option Module 10Base-FL 163

35010574 12/2018 137

NOM

138 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOM 211 00
35010574 12/2018

Chapter 14
140 NOM 211 00: Modbus Plus Option Module

140 NOM 211 00: Modbus Plus Option Module

Purpose
This chapter contains information of the 140 NOM 211 00 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 140
Indicators 146
Error Codes 147
Specifications 149

35010574 12/2018 139

140 NOM 211 00

Presentation

Function
The 140 NOM 211 00 is a single channel Network Option Modul (NOM), connected via a twisted
pair Modbus Plus cable network

Illustration
The following figure shows the parts of the Modbus Plus 140 NOM 211 00 modules.

1 LED Area
2 Comm Parameter Slide Switch
3 Modbus Connector
4 Modbus Plus Connector
5 Model Number, Module Description, Color Code
6 Removable door
7 Customer Identification Label, (Fold label and place it inside door)

140 35010574 12/2018

 140 NOM 211 00

Front Panel Switches

Two, three-position slide switches are located on the front of the unit. The switch on the left is not
used. The three-position slide switch on the right is used to select the comm parameter settings for
the Modbus (RS-232) port provided with the Modbus Plus option module. Three options are
available, as shown below.
The following figure shows the front panel switches.

NOTE: If the left-hand switch is in the upper position and right-hand switch is set to mem then, as
of firmware version 2.20, bridge mode is deactivated. This means that the network connection
between Modbus and Modbus Plus is locked.
The NOM hardware defaults to bridge mode when the front panel switch is set to RTU or ASCII
mode. When networking controllers, a panel device connected to the NOM Modbus port can
communicate with the controller to which it is conected, as well as log into any nodes on the
Modbus Plus network.

Rear Panel Switches

Two rotary switches are located on the rear panel of the modules. They are used together to set
the Modbus Plus node and Modbus port address for the unit.
NOTE: The highest address that may be set with these switches is 64.
Rotary SW1 (top switch) sets the upper digit (tens), and rotary SW2 (bottom switch) sets the lower
digit (ones) of the Modbus Plus node address. The illustration below shows the setting for an
example address of 11.

35010574 12/2018 141

140 NOM 211 00

SW1 and SW2 Switches Figure

The following figure shows the SW1 and SW2 switches.

NOTE: If "0," or an address greater than 64 is selected, the Modbus + LED will be "on" steady, to
indicate the selection of an invalid address.

SW1 and SW2 Address Settings

The following table shows the address settings for the SW1 and SW2 switches.

Node Address SW1 SW2

1 ... 9 0 1 ... 9
10 ... 19 1 0 ... 9
20 ... 29 2 0 ... 9
30 ... 39 3 0 ... 9
40 ... 49 4 0 ... 9
50 ... 59 5 0 ... 9
60 ... 64 6 1 ... 4

NOTE: If "0," or an address greater than 64 is selected, the Modbus + LED will be "on" steady, to
indicate the selection of an invalid address.

142 35010574 12/2018

 140 NOM 211 00

ASCII Comm Port Parameters

The following table shows the fixed setting of the ASCII comm port parameters.

Baud 2,400
Parity Even
Data Bits 7
Stop Bits 1
Device Address Rear panel rotary switch setting

Setting the slide switch to the middle position assigns remote terminal unit (RTU) functionality to
the port; the following comm parameters are set and cannot be changed:

RTU Comm Port Parameters

The following table shows the RTU comm port parameters.

Baud 9,600
Parity Even
Data Bits 8
Stop Bits 1
Device Address Rear panel rotary switch setting

Setting the slide switch to the bottom position gives you the ability to assign comm parameters to
the port in software; the following parameters are valid.

35010574 12/2018 143

140 NOM 211 00

Valid Comm Port Parameters

The following table shows the valid comm port parameters.

Baud 19,200 1,200

9,600 600
7,200 300
4,800 150
3,600 134.5
2,400 110
2,000 75
1,800 50
Data Bits 7/8
Stop Bits 1/2
Parity Enable/Disable Odd/Even
Device Address Rear panel rotary switch setting

Modbus Connector Pinouts

The NOM modules are equipped with a nine-pin RS-232C connector that supports Modicon’s
proprietary Modbus communication protocol. The following is the Modbus port pinout connections
for 9-pin and 25-pin connections.
The following figures show the Modbus port pinout connections for 9-pin (left) and 25-pin (right).
;

The following is the abbreviation key for the above figure.

TX: Transmitted Data DTR: Data Terminal Ready

RX: Received Data CTS: Clear to Send
RTS: Request to Send N/C: No Connection
DSR: Data Set Ready CD: Carrier Detect

144 35010574 12/2018

 140 NOM 211 00

Modbus Ports Pinout Connections for Portable Computers

The following figure shows the Modbus port pinout connections for 9-pin portable computers.

35010574 12/2018 145

140 NOM 211 00

Indicators

Illustration
The following figure shows the Modbus Plus NOM LED indicators.

Description
The following table shows the Modbus Plus NOM LED Descriptions.

LEDs Color Indication when On

Ready Green The module has passed powerup diagnostics.
Run Green Indicates that the unit is in kernel mode–should always be OFF
during normal operations.
Modbus Green Indicates communication is active on the single RS-232 serial
port.
Modbus+ Green Indicates communication is active on the Modbus Plus port.

146 35010574 12/2018

 140 NOM 211 00

Error Codes

Error Codes Table

The blinking run LED error codes for the NOM module shows the number of times the Run LED on
the NOM module blinks for each type of error and the crash codes for each (all codes are in hex).
The following table shows the blinking run LED error codes for the NOM module.

Number of Blinks Code Error

Steady 014H normal power down event
2 815 RAM sequence error
3 49H illegal data command received by bypass code
4BH diagnostics test pattern invalid in the icb block
4CH diagnostics test pattern invalid in the page 0
4DH icb address not the same as found in hcb
4EH bad code selected for mstrout_sel proc
52H config table exec_id is different than the sys table exec_id
53H got a pupinit hook for neither S985 nor S975 addr
56H did not get bus ack form 984 interface within 400 ms
59H unexpected modbus port state in send command to 680
proc
5AH system table missing
5BH bad DPM critical byte write
4 616H bad or unexpected interrupt
617H loopback error on modbus port 1
618H parity error
619H set port greater than 21
61AH controller ram size is less than 8k
621H modbus cmd-buffer overflow
622H modbus cmd-length is zero
623H modbus abort command error
624H bad modbus state trn-int
625H bad modbus state rcv-int
626H bad comm state trn_asc
627H transmit underflow error
628H bad comm state trn_tru
629H bad comm state rcv_asc
62AH bad comm state rcv_rtu

35010574 12/2018 147

140 NOM 211 00

62BH bad transmit comm state

62CH bad receive comm state
62DH bad modbus state tmr0_evt
62EH bad uart interrupt
631H UPI timeout error
632H bad UPI response opcode
633H UPI bus diagnostic error
634H mbp bus interference error
635H bad mbp response opcode
636H timeout waiting for mbp
637H mbp out of synchronization
638H mbp invalid path
639H peer did not respond with complement of the opcode
63AH peer unable to come out of transitions at powerup
681H bad master state
682H bad slave state
683H unknown routing failure to send
684H bad port number in set () proc
685H bad port number in reset () proc
686H bad port number in getport () proc
687H bad port number in bitpos () proc
688H bad port number in enable_transmit_interrupt () proc
689H bad port number in enable_receive_interrupt () proc
68AH bad port number in disable_transmit_interrupt () proc
68BH bad port number in
691H privilege flag is not reset in the session timeout proc
692H bad port number in chkmst_hdw () proc
6A1H unknown controller type in reset busy flag
6A2H unknown function code in generate_poll_cmd () proc
6A3H unknown function code in generate_logout_msg () proc
6A4H slave link timeout on port other than port #9
6A5H illegal bypass command received by bypass code
5 513H RAM address test error
6 412H RAM data test error
7 311H PROM checksum error

148 35010574 12/2018

 140 NOM 211 00

Specifications

General Specifications
General Specifications

Power Dissipation 4W
Bus Current required 750 mA (max.)

Communication Ports
Communication Ports

1 Modbus Plus network

(RS-485) port (9-pin
connector)
1 Modbus (RS-232) serial A bridge mode capability in the module permits a panel device
port (9-pin connector) connected to this port to access nodes on the Modbus Plus
network or to access the local PLC directly without having to go
out onto the network.

Diagnostics
Diagnostics

Power Up RAM
RAM Address
Executive Checksum
Processor
Runtime RAM
RAM Address
Executive Checksum
Processor

35010574 12/2018 149

140 NOM 211 00

150 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOM 212 00
35010574 12/2018

Chapter 15
140 NOM 212 00: Modbus Plus Option Module

140 NOM 212 00: Modbus Plus Option Module

Purpose
This chapter contains information of the 140 NOM 212 00 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 152
Indicators 158
Error Codes 159
Specifications 161

35010574 12/2018 151

140 NOM 212 00

Presentation

Function
The 140 NOM 212 00 is a dual channel Network Option Modul (NOM), connected via a twisted pair
Modbus Plus cable network

Illustration
The following figure shows the parts of the Modbus Plus 140 NOM 212 00 modules.

1 LED Area
2 Comm Parameter Slide Switch
3 Modbus Connector
4 Modbus Plus Connector (Chan A)
5 Modbus Plus Connector (Chan B)
6 Model Number, Module Description, Color Code
7 Removable door
8 Customer Identification Label, (Fold label and place it inside door)

152 35010574 12/2018

 140 NOM 212 00

Front Panel Switches

Two, three-position slide switches are located on the front of the unit. The switch on the left is not
used. The three-position slide switch on the right is used to select the comm parameter settings for
the Modbus (RS-232) port provided with the Modbus Plus option module. Three options are
available, as shown below.
The following figure shows the front panel switches.

NOTE: If the left-hand switch is in the upper position and right-hand switch is set to mem then, as
of firmware version 2.20, bridge mode is deactivated. This means that the network connection
between Modbus and Modbus Plus is locked.
The NOM hardware defaults to bridge mode when the front panel switch is set to RTU or ASCII
mode. When networking controllers, a panel device connected to the NOM Modbus port can
communicate with the controller to which it is conected, as well as log into any nodes on the
Modbus Plus network.

Rear Panel Switches

Two rotary switches are located on the rear panel of the modules. They are used together to set
the Modbus Plus node and Modbus port address for the unit.
NOTE: The highest address that may be set with these switches is 64.
Rotary SW1 (top switch) sets the upper digit (tens), and rotary SW2 (bottom switch) sets the lower
digit (ones) of the Modbus Plus node address. The illustration below shows the setting for an
example address of 11.

35010574 12/2018 153

140 NOM 212 00

SW1 and SW2 Switches Figure

The following figure shows the SW1 and SW2 switches.

NOTE: If "0," or an address greater than 64 is selected, the Modbus + LED will be "on" steady, to
indicate the selection of an invalid address.

SW1 and SW2 Address Settings

The following table shows the address settings for the SW1 and SW2 switches.

Node Address SW1 SW2

1 ... 9 0 1 ... 9
10 ... 19 1 0 ... 9
20 ... 29 2 0 ... 9
30 ... 39 3 0 ... 9
40 ... 49 4 0 ... 9
50 ... 59 5 0 ... 9
60 ... 64 6 1 ... 4

NOTE: If "0," or an address greater than 64 is selected, the Modbus + LED will be "on" steady, to
indicate the selection of an invalid address.

154 35010574 12/2018

 140 NOM 212 00

ASCII Comm Port Parameters

The following table shows the fixed setting of the ASCII comm port parameters.

Baud 2,400
Parity Even
Data Bits 7
Stop Bits 1
Device Address Rear panel rotary switch setting

Setting the slide switch to the middle position assigns remote terminal unit (RTU) functionality to
the port; the following comm parameters are set and cannot be changed:

RTU Comm Port Parameters

The following table shows the RTU comm port parameters.

Baud 9,600
Parity Even
Data Bits 8
Stop Bits 1
Device Address Rear panel rotary switch setting

Setting the slide switch to the bottom position gives you the ability to assign comm parameters to
the port in software; the following parameters are valid.

35010574 12/2018 155

140 NOM 212 00

Valid Comm Port Parameters

The following table shows the valid comm port parameters.

Baud 19,200 1,200

9,600 600
7,200 300
4,800 150
3,600 134.5
2,400 110
2,000 75
1,800 50
Data Bits 7/8
Stop Bits 1/2
Parity Enable/Disable Odd/Even
Device Address Rear panel rotary switch setting

Modbus Connector Pinouts

The NOM modules are equipped with a nine-pin RS-232C connector that supports Modicon’s
proprietary Modbus communication protocol. The following is the Modbus port pinout connections
for 9-pin and 25-pin connections.
The following figures show the Modbus port pinout connections for 9-pin (left) and 25-pin (right).

156 35010574 12/2018

 140 NOM 212 00

Modbus Ports Pinout Connections for Portable Computers

The following figure shows the Modbus port pinout connections for 9-pin portable computers.

35010574 12/2018 157

140 NOM 212 00

Indicators

Illustration
The following figure shows the Modbus Plus NOM LED indicators.

Description
The following table shows the Modbus Plus NOM LED Descriptions.

LEDs Color Indication when On

Ready Green The module has passed powerup diagnostics.
Run Green Indicates that the unit is in kernel mode–should always be OFF
during normal operations.
Modbus Green Indicates communication is active on the single RS-232 serial
port.
Modbus+ Green Indicates communication is active on the Modbus Plus port.
Error A Red There is an error condition on Cable A
Error B Red There is an error condition on Cable B

158 35010574 12/2018

 140 NOM 212 00

Error Codes

Error Codes Table

The blinking run LED error codes for the NOM module shows the number of times the Run LED on
the NOM module blinks for each type of error and the crash codes for each (all codes are in hex).
The following table shows the blinking run LED error codes for the NOM module.

Number of Blinks Code Error

Steady 014H normal power down event
2 815 RAM sequence error
3 49H illegal data command received by bypass code
4BH diagnostics test pattern invalid in the icb block
4CH diagnostics test pattern invalid in the page 0
4DH icb address not the same as found in hcb
4EH bad code selected for mstrout_sel proc
52H config table exec_id is different than the sys table exec_id
53H got a pupinit hook for neither S985 nor S975 addr
56H did not get bus ack form 984 interface within 400 ms
59H unexpected modbus port state in send command to 680
proc
5AH system table missing
5BH bad DPM critical byte write
4 616H bad or unexpected interrupt
617H loopback error on modbus port 1
618H parity error
619H set port greater than 21
61AH controller ram size is less than 8k
621H modbus cmd-buffer overflow
622H modbus cmd-length is zero
623H modbus abort command error
624H bad modbus state trn-int
625H bad modbus state rcv-int
626H bad comm state trn_asc
627H transmit underflow error
628H bad comm state trn_tru
629H bad comm state rcv_asc
62AH bad comm state rcv_rtu

35010574 12/2018 159

140 NOM 212 00

62BH bad transmit comm state

62CH bad receive comm state
62DH bad modbus state tmr0_evt
62EH bad uart interrupt
631H UPI timeout error
632H bad UPI response opcode
633H UPI bus diagnostic error
634H mbp bus interference error
635H bad mbp response opcode
636H timeout waiting for mbp
637H mbp out of synchronization
638H mbp invalid path
639H peer did not respond with complement of the opcode
63AH peer unable to come out of transitions at powerup
681H bad master state
682H bad slave state
683H unknown routing failure to send
684H bad port number in set () proc
685H bad port number in reset () proc
686H bad port number in getport () proc
687H bad port number in bitpos () proc
688H bad port number in enable_transmit_interrupt () proc
689H bad port number in enable_receive_interrupt () proc
68AH bad port number in disable_transmit_interrupt () proc
68BH bad port number in
691H privilege flag is not reset in the session timeout proc
692H bad port number in chkmst_hdw () proc
6A1H unknown controller type in reset busy flag
6A2H unknown function code in generate_poll_cmd () proc
6A3H unknown function code in generate_logout_msg () proc
6A4H slave link timeout on port other than port #9
6A5H illegal bypass command received by bypass code
5 513H RAM address test error
6 412H RAM data test error
7 311H PROM checksum error

160 35010574 12/2018

 140 NOM 212 00

Specifications

General Specifications
General Specifications

Power Dissipation 4 W (typical)

Bus Current required 780 mA

Communication Ports
Communication Ports

2 Modbus Plus network For dual connectivity on a single Modbus Plus network. These
(RS-485) port (9-pin ports handle identical versions of all inbound and outbound
connector) transactions and keep track of the data paths used for these
transactions
1 Modbus (RS-232) serial A bridge mode capability in the module permits a panel device
port (9-pin connector) connected to this port to access nodes on the Modbus Plus
network or to access the local PLC directly without having to go
out onto the network.

Diagnostics
Diagnostics

Power Up RAM
RAM Address
Executive Checksum
Processor
Runtime RAM
RAM Address
Executive Checksum
Processor

35010574 12/2018 161

140 NOM 212 00

162 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOM 252 00
35010574 12/2018

Chapter 16
140 NOM 252 00: Modbus Plus Option Module 10Base-FL

140 NOM 252 00: Modbus Plus Option Module 10Base-FL

Purpose
This chapter contains information of the 140 NOM 252 00 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 164
Indicators 170
Fiber Optic Cable Connections 171
Specifications 181

35010574 12/2018 163

140 NOM 252 00

Presentation

Overview
The Modbus Plus on Fiber module provides connectivity to Modbus Plus nodes by fiber cable.
There are many benefits that result from the use of fiber optics. Some of these benefits include:
 Longer distances between nodes (up to 3 km), thereby, increasing the total length of the
network.
 Fiber optic medium is not susceptible to the effects of electromagnetic interference, RF
interference, and lightning.
 Intrinsically safe links that are required in many hazardous industrial environments.
 Total electrical isolation between terminal points on the link

Illustration
The following figure shows the parts of the Modbus Plus 140 NOM 252 00 module.

1 LED Area
2 Modbus Connector
3 Comm Parameter Slide Switch
4 Port 2 TX and RX Connectors
5 Port 1 TX and RX Connectors
6 Model Number, Module Description, Color Code
7 Removable door
8 Customer Identification Label, (Fold label and place it inside door)

164 35010574 12/2018

 140 NOM 252 00

Front Panel Switch

A three-position slide switch is located on the front of the unit. This switch is used to select the
comm parameter settings for the Modbus (RS-232) port. Three options are available, as shown
below.
The following figure shows the front panel switch.

Setting the slide switch to the top position assigns ASCII functionality to the port; the following
comm parameters are set and cannot be changed.

ASCII Comm Port Parameters

The following table shows the fixed setting of the ASCII comm port parameters.

Baud 2,400
Parity Even
Data Bits 7
Stop Bits 1
Device Address Rear panel rotary
switch setting

Setting the slide switch to the middle position assigns remote terminal unit (RTU) functionality to
the port; the following comm parameters are set and cannot be changed:

35010574 12/2018 165

140 NOM 252 00

RTU Comm Port Parameters

The following table shows the RTU comm port parameters.

Baud 9,600
Parity Even
Data Bits 8
Stop Bits 1
Device Address Rear panel rotary switch setting

Setting the slide switch to the bottom position gives you the ability to assign comm parameters to
the port in software; the following parameters are valid.

Valid Comm Port Parameters

The following table shows the valid comm port parameters.

Baud 19,200 1,200

9,600 600
7,200 300
4,800 150
3,600 134.5
2,400 110
2,000 75
1,800 50
Data Bits 7/8
Stop Bits 1/2
Parity Enable/Disable Odd/Even
Device Address Rear panel rotary switch setting

Rear Panel Switches

Two rotary switches are located on the rear panel of the modules. They are used together to set
the Modbus Plus node and Modbus port address for the unit.
NOTE: The highest address that may be set with these switches is 64.
Rotary SW1 (top switch) sets the upper digit (tens), and rotary SW2 (bottom switch) sets the lower
digit (ones) of the Modbus Plus node address. The illustration below shows the setting for an
example address of 11.

166 35010574 12/2018

 140 NOM 252 00

SW1 and SW2 Switches Figure

The following figure shows the SW1 (top) and SW2 (bottom) switches.

SW1 and SW2 Address Settings

The following figure shows the node address settings for the SW1 and SW2 switches.

Node Address SW1 SW2

1 ... 9 0 1 ... 9
10 ... 19 1 0 ... 9
20 ... 29 2 0 ... 9
30 ... 39 3 0 ... 9
40 ... 49 4 0 ... 9
50 ... 59 5 0 ... 9
60 ... 64 6 1 ... 4

NOTE: If "0" or an address greater than 64 is selected, the Modbus + LED will be "on" steady, to
indicate the selection of an invalid address.

Modbus Connector
The NOM 252 00 module is equipped with an RS-232 port (see below) located on the front of the
module. This port uses an eight-position RJ45 (phone jack-type) connector.

35010574 12/2018 167

140 NOM 252 00

Modbus pin 1 Figure

The following figure shows the NOM 252 00 Pin 1 connector.

NOTE: A D-shell adapter is available from Modicon for NOM 252 00-to-computer connections: a
(110 XCA 20 300) 9-pin adapter for PC-AT type computers (see the illustration pinout table below).

Pinouts Figures
The following figures show the 9-pin adapter front view (left) and side view (right).

168 35010574 12/2018

 140 NOM 252 00

Connector Pinouts Figure

The following figure shows the 9-pin RJ45 connector schematic.

BJ45 Cable Types

This following shows an example of the 110 XCA 282 0X cable. A table is also provided which
includes part numbers and cable lengths.

RJ45 Connector Figure

The following figure shows the RJ45 connector (Modicon Part # 110 XCA 282 OX).

BJ45 Cable Part Numbers Table

Cable Part Numbers Cable Lengths

110 XCA 282 01 3 ft. (0.91 m)
110 XCA 282 02 10 ft. (3 m)
110 XCA 282 03 20 ft. (6 m)

35010574 12/2018 169

140 NOM 252 00

Indicators

Illustration
The following figure shows the Modbus Plus on Fiber LED indicators.

Description
The following table shows the Modbus Plus on fiber LED descriptions.

LEDs Color Indication when On

Ready Green The module has passed powerup diagnostics.
Run Green Indicates that the unit is in kernel mode – should always be OFF
during normal operations. Note: The table for the NOM 21X 00
shows the number of times the RUN LED on the Modbus Plus on
Fiber Module blinks for each type of error and the crash codes for
each (all codes are in hex).
Modbus Green Indicates communication is active on the single RS-232 serial port.
Modbus+ Green Indicates communication is active on the Modbus Plus port.
Fport1 Green Indicates an optical signal has been received on fiber optic Port 1.
Fport2 Green Indicates an optical signal has been received on fiber optic Port 2.
FRNGoff Red Indicates the first break in a self healing ring.

170 35010574 12/2018

 140 NOM 252 00

Fiber Optic Cable Connections

Fiber Optic Cable Connections

The NOM 252 00 module is connected in the Quantum system by a fiber optic cable (see below).
The cable has two strands. Each module transmits a uni-directional signal. For this reason, each
strand must be connected to the transmit port on one module and the receive port on the other.
One strand of the fiber optic cable is marked at 10-inch (25 cm) intervals with the manufacturer’s
name and the cable specifications. This is the only way to distinguish the two strands.

Fiber Optic Cable Connections Figure

The following figure shows the fiber optic cable connections.

35010574 12/2018 171

140 NOM 252 00

Connecting the Fiber Optic Cable

The following steps show how to connect the fiber optic cable.

Step Action
1 Remove the protective plastic coverings from the cable ports and the tips of the
cable. Snap one of the fiber cable clasps (shipped with the module) over the
cable so that the wider end of the tool is closest to the cable end.

2 Turn the connection ring so that one of the arrows on the side of the ring lines up
with the ridge inside.

3 a. Slide the tool up to the connection ring.

b. Gripping the cable with the plastic cable clasp, slide the cable end onto the
lower cable port. The arrow and the ridge on the connection ring should line up
with the slot on the left of the cable port.
c. Use the clasp to push the cable over the tab on top of the port.
d. Turn the cable to the right, so that the tab locks securely
e. Remove the clasp.
f. Repeat this process with the remaining strand of cable.

172 35010574 12/2018

 140 NOM 252 00

Fiber Optic Configurations

Here are four typical configurations that show the wide range of the network architecture:
 Point-to-point connection
 Bus configuration
 Tree configuration
 Self-healing ring configuration

Point-to-Point Configuration
This type of configuration (see below) allows communication over the distance of up to 3 km
through harsh industrial environments.

Point-to-Point Configuration Example Figure

The following figure shows the point-to-point configuration.

Bus Configuration
This type of configuration is used when it is required to connect a number of fiber nodes and can
be used to increase the distance of a standard Modbus Plus network by changing to a fiber
medium. This kind of network allows the connection of up to 32 Quantum NOM 252 nodes over the
distance of 5 km.
The following illustrations show the NOM 252 00 module in a mixed fiber optic/twisted pairs bus
configuration network and a straight fiber optic bus configuration network.
NOTE: The loss of a single node in this configuration disables the rest of the network.

35010574 12/2018 173

140 NOM 252 00

Bus Configuration Example 1

The following figure shows the mixed fiber optic/copper network.

Bus Configuration Example 2

The following figure shows the straight fiber optic network.

NOTE: The distance between nodes on fiber is limited by the maximum allowable power loss from
end-to-end (3 km over 62.5 mm fiber). Power loss includes the fiber optic cable attenuation,
connector losses at the Fiber Optic Receiver and Transmitter ports, and the system margin of 3 dB.
In this configuration, the end NOM 252 00 in this configuration will have the FRNGoff LED active.
It also displays the Cable B Framing error in the MBPSTAT (in ladder logic).

174 35010574 12/2018

 140 NOM 252 00

Tree Configuration
Using tree configurations allows for greater flexibility in the layout of Modbus Plus and NOM 252
00 networks. The following illustrations are samples tree configurations. Additional repeaters may
be connected in order to extend communication between electrical links.

Tree Configuration Example

The following figure shows the tree configuration.

35010574 12/2018 175

140 NOM 252 00

Self-healing Ring Configuration

This configuration can be achieved by connecting the unused fiber optic ports of the first and last
NOM 252 00 directly or through the fiber optic repeater, if a mixed fiber optic/twisted pairs network
is used. This type of connection has all the advantages of the previously described configurations,
along with built-in redundancy. A broken connection between any two Quantum modules in the ring
will automatically reconfigure the network to the bus configuration, and maintain communication.

Self-healing Ring Configuration Example

The following figure shows a self-healing ring configuration example.

176 35010574 12/2018

 140 NOM 252 00

Hot Standby Systems Figure

The following figure shows the self-healing ring configuration for hot standby systems.

35010574 12/2018 177

140 NOM 252 00

Network Status
The information about the condition of the network is presented in the form of Network Status. This
information indicates the loss of connection (the first break in the self-healing ring) and is similar to
the way the existing 140 NOM 212 00 reports the loss of the redundant cable.
The break in the fiber cable will be detected by the module not receiving the signal from the cable
break side. The incident will be reported by MBPSTAT as a Cable B Framing error. This condition
also activates the FRNGoff LED on the module front.

Recommended Materials for Fiber Optic Links

Modicon does not manufacture fiber optic products such as cables, connectors, or special tools.
However, we have experience with third party suppliers of materials, and are able to provide
guidelines on product compatibility.

Connectors
The following table shows the connector types

Connector type Part number Operating temperature

ST bayonet (epoxy) 3M 6105 -40 ... +80 °C
ST bayonet (hot melt) 3M 6100 -40 ... +60 °C
ST bayonet (epoxy) AMP 501380-5 series -30 ... +70 °C
ST bayonet (epoxy) AMP 503415-1 series -20 ... +75 °C
Light crimp ST-style AMP 503453-1 series -20 ... + 60 °C
Mechanical line splice (one 3M 2529 Fiberlok1 II -40 ... +80 °C
size fits all)

NOTE: All connectors must have a short boot for strain relief.

Termination Kits
The following table shows the termination kits.

Kit type Part number Description

Bayonet ST (eoxy) AMP 503746-1 For all epoxy type ST style
Light crimp XTC AMP 50330-2 For all light crimp
Mechanical line splice 3M 2530 Fiber splice prep kit, complete with
cleaving tool
3M hot melt 3M 05-00185 110 V termination kit
3M 05-00187 220 V termination kit

178 35010574 12/2018

 140 NOM 252 00

Other Tools Table

The following table shows other tools that may be needed for fiber optic links.

Product Part number Description/use

3M (Photodyne) optical 9XT Hand-held optical source driver (requires
source driver a light source)
3M (Photodyne) optical 1700-0850-T 850 nm Light Source, ST Connectors for
light source 9XT
3M (Photodyne) power 17XTA-2041 Hand-held fiber optic power meter
meter
3M optical light source, 7XE-0660-J Use with 9XT to troubleshoot raw fiber,
660 nm, visible requires FC/ST patch cord
3M FC/ST patch cord BANAV-FS-0001 Connects FC connector on 7XE to ST
3M bare fiber adapter, 8194 Allows the use of above source and
ST-compatible meter to test raw fiber (two required)

Cables
It is recommended that you use 62.5/125 mm cable (such as AMP 503016-1, AMP 502986-1, or
equivalent) with a maximum attenuation of 3.5 dB/km in most of the configurations.
NOTE: Modicon recommends using the 52-0370-000 cable.
NOTE: All cables must have a maximum cable diameter of not more than 3 mm at the terminal
side.

Connections
The following information discusses connecting the NOM 252 00 on fiber cable, adding a new
mode to the network, and repairing the break in the cable.
NOTE: When a new network is assembled, it is recommended that you connect all cables before
powering up the system. Connect fiber optic cables as described previously in this section.

Adding a New Node to the Network

If a new node is added to an existing network in order to extend the network (at the end of any
configuration), then a new node may be connected first by fiber cable and then hot-swapped to the
backplane to avoid errors to the existing network.
If a new node is added to the middle of the network, disconnect the fiber optic cables from one side
of the existing NOM 252 module, and connect to port 1 or 2 of the new node. Additional fiber optic
cable then needs to be connected to the second port of the new NOM 252 and to the next
NOM 252 in the network. Finally, hot-swap the new NOM 252 to the backplane.

35010574 12/2018 179

140 NOM 252 00

Repairing the Break in the Cable

Because the NOM 252 00 will stop transmitting in the direction from which it receives no signal,
replaceing a broken fiber optic cable and reconnectioning do not suffice to re-establish
communication over that segment. Hot-swapping only one NOM 252 at the repaired connections
is required to complete the connection.
NOTE: Breakage of any fiber connectors or fiber optic cables is the equivalent to breaking the trunk
cable in a copper-based Modbus Plus network.
For the self-healing ring configuration, repairing the first break in the fiber optic network has to be
scheduled when one of the units on either side of the repaired break can be hot-swapped, without
creating further problems by disconnecting the node.
NOTE: Self-healing configurations are not considered as redundant networks. Redundant
networks yield a high system availability.

Calculations
Use the following formula to calculate the number of NOM 252 00 modules in a fiber network:

Step Action
1 The total allowable pulse width distortions and jitter are limited to 20% of the bit
period and is 200 nsec for the full fiber optic network.
2 The jitter contributed by the NOM 252 is 5 nsec max.
3 Jitter contributed by fiber optic repeaters (if used) is 40 nsec.
4 Use the following formula to determine the number (N) of chained repeaters:

where "L" is the total cable length (km), and "X" is the jitter (added by the fiber
optic cable) in nsec/km:
X = 3 ns/km for 50/125 micron meters
5 ns/km for 62.5/125 micron meters
7.5 ns/km for 100/140 micron meters

180 35010574 12/2018

 140 NOM 252 00

Specifications

General Specifications
General Specifications

Power Dissipation 4 W (typical)

Bus Current required 780 mA
External Power Not required

Communication Ports
Communication Ports

Optical Ports 2 (consisting of an optical receiver and transmitter)

Modbus Port 1 RJ45 (phone jack-type) connector

Diagnostics
Diagnostics

Power Up RAM
RAM Address
Executive Checksum
Processor
Runtime RAM
RAM Address
Executive Checksum

Optical Transmission
Optical Transmission

Interface ST-Type connector

PulseWidth Disstortion and Jitter 5 ns or better
Wavelength 820 nm
Power Loss Budget (includes 3 dB of 50/125 micron fiber -6.5 dB
system margins) 62.5/125 micron fiber -11 dB
100/140 micron fiber -16.5 dB
Maximum distance for point-to- point 2 km over 50 micron fiber
connection 3 km over 62.5 micron fiber
3 km over 100 micron fiber
Maximum System Length in Self Healing 10 km over 62.5 micron fiber
Ring Configuration

35010574 12/2018 181

140 NOM 252 00

Optical Transmitter Specifications

Optical Transmitter Specifications

Optical Power (Measured -12.8 ... -19.8 dBm average power in 50/125 micron fiber cable
with 1 m test fiber) -9.0 ... -16 dBm average power in 62.5/125 micron fiber cable
-3.5 ... -10.5 dBm average power in 100/140 micron fiber cable
Rise/Fall Time 20 ns or better
Silence (OFF leakage) -43 dBm

Optical Receiver Specifications

Optical Receiver Specifications

Receiver Sensitivity -30 dBm average power

Dynamik range -20 dB
Detected Silence -36 dBm

182 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
Ethernet Modules
35010574 12/2018

Part V
Quantum Ethernet Modules

Quantum Ethernet Modules

Introduction
This part provides information about the different Ethernet modules of the Quantum product series.

What Is in This Part?

This part contains the following chapters:
Chapter Chapter Name Page
17 140 NOE xxx xx: Ethernet Module General Overview 185
18 140 NOE 211 x0: TCP/IP 10Base-T Ethernet Module 195
19 140 NOE 251 x0: TCP/IP 10Base-FL Ethernet Module 201
20 140 NOE 311 00: SY/MAX 10Base-T Ethernet Module 207
21 140 NOE 351 00: SY/MAX 10Base-FL Ethernet Module 213
22 140 NOE 771 00: TCP/IP 10/100 Ethernet Module 219
23 140 NOE 771 01: TCP/IP 10/100 Ethernet Module 225
24 140 NOE 771 10: TCP/IP 10/100 FactoryCast Ethernet Module 231
25 140 NOE 771 11: TCP/IP 10/100 FactoryCast Ethernet Module 239
26 140 NWM 100 00: TCP/IP 10/100 FactoryCast HMI Ethernet Module 245

35010574 12/2018 183

Ethernet Modules

184 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOE xxx xx: Ethernet Module General Overview
35010574 12/2018

Chapter 17
140 NOE xxx xx: Ethernet Module General Overview

140 NOE xxx xx: Ethernet Module General Overview

At a Glance
This chapter contains general information about the 140 NOE ••• •• and 140 NWM 100 00 Ethernet
modules.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
General Information 186
Modicon Quantum Ethernet Modules Overview 187
Indicators for Ethernet Modules 192

35010574 12/2018 185

140 NOE xxx xx: Ethernet Module General Overview

General Information

Introduction
This part provides information on the following Quantum Ethernet Modules:

Ethernet Module Communication Channels Bus Current

Required
140 NOE 211 00 1 10Base-T Ethernet network (RJ-45) port 1A
140 NOE 251 00 1 10Base-FL Ethernet network (ST-45) port 1A
140 NOE 311 00 One 10BASE-T Ethernet network (RJ45) port. 1A
140 NOE 351 00 Two 10BASE-FL Ethernet network (ST-style) port. 1A
140 NOE 771 00 100 BASE-FX Fiber optics (MT-RJ) port 750 mA
10/100BASE-T (RJ-45) port
140 NOE 771 01 100 BASE-FX Fiber optics (MT-RJ) port 750 mA
10/100BASE-T (RJ-45) port
140 NOE 771 10 FactoryCast 100 BASE-FX Fiber optics (MT-RJ) port 750 mA
10/100BASE-T (RJ-45) port
140 NOE 771 11 FactoryCast 100 BASE-FX Fiber optics (MT-RJ) port 750 mA
10/100BASE-T (RJ-45) port
140 NWM 100 00 100 BASE-FX Fiber optics (MT-RJ) port 900 mA
10/100BASE-T (RJ-45) port

TCP/IP Ethernet Modules

Quantum TCP/IP Ethernet modules make it possible for a Quantum controller to communicate with
devices on an Ethernet network using TCP/IP - the de facto standard protocol. An Ethernet module
may be inserted into an existing Quantum system and connected to existing Ethernet networks via
fiber optic or twisted pair cabling.

Sy/Max Ethernet Modules

Quantum Sy/Max Ethernet modules are Interfaces that can be placed in a Quantum backplane, to
connect Quantum controllers to Sy/Max devices and applications.

186 35010574 12/2018

 140 NOE xxx xx: Ethernet Module General Overview

Modicon Quantum Ethernet Modules Overview

Overview
The following information provides overviews of all Modicon Quantum Ethernet modules.

General Description
The Modicon Quantum Ethernet module, shown below, is one of the latest models in a line of
Modicon Quantum Ethernet TCP/IP modules designed to make it possible for a Modicon Quantum
PLC to communicate with devices over an Ethernet network. The electronics for the Ethernet
modules are contained in a standard Modicon Quantum single-width case that takes up one slot in
a Modicon Quantum backplane. The module, which is capable of being hot swapped, can be
plugged into any available slot in the backplane.
The NOE 771 x0 and NOE 771 x1 modules provide real-time peer-to-peer communications and
I/O scanning and a Modbus/TCP server. The included HTTP services provide maintenance and
configuration utilities to the module.

35010574 12/2018 187

140 NOE xxx xx: Ethernet Module General Overview

Front View
The following figure shows the front of the NOE 771 00 Ethernet module as an example for all
Ethernet modules.

1 model number, module description, color code

2 LED display
3 IP Address writable area
4 Global address label
5 100 BASE-FX MT-RJ cable connector
6 10/100 BASE-T RJ45 cable connector
7 removable door

188 35010574 12/2018

 140 NOE xxx xx: Ethernet Module General Overview

Key Ethernet Services

The key Ethernet services of the 140 NOE 771 (-00, -01, -10, -11) and 140 NWM 100 00 models
are listed below:

Service -00 -01 -10 -11 NWM

HTTP Server (see Quantum using X X X X X
EcoStruxure™ Control Expert, Ethernet Network
Modules, User Manual)
FTP Server (see Quantum using EcoStruxure™ X X X X X
Control Expert, Ethernet Network Modules, User
Manual)
Flash File System (see Quantum using X X X X X
EcoStruxure™ Control Expert, Ethernet Network
Modules, User Manual)
BOOTP Client (see Quantum using X X X X X
EcoStruxure™ Control Expert, Ethernet Network
Modules, User Manual)
Address Server (see Quantum using X X X X
EcoStruxure™ Control Expert, Ethernet Network
Modules, User Manual)
SNMP V2 Agent (Network Management Service) X X X X X
(see Quantum using EcoStruxure™ Control
Expert, Ethernet Network Modules, User Manual)
Modbus Messaging (see Quantum using X X X X X
EcoStruxure™ Control Expert, Ethernet Network
Modules, User Manual)
I/O Scanner (see Quantum using EcoStruxure™ X X X
Control Expert, Ethernet Network Modules, User
Manual)
Hot Standby X X
Global Data (Publish/Subscribe) (see Quantum X X
using EcoStruxure™ Control Expert, Ethernet
Network Modules, User Manual)
Bandwidth Monitoring (see Quantum using X X
EcoStruxure™ Control Expert, Ethernet Network
Modules, User Manual)
Fast Device Replacement (Server) X X
(see Quantum using EcoStruxure™ Control
Expert, Ethernet Network Modules, User Manual)
Enhanced Web Diagnosis (see Quantum using X X X
EcoStruxure™ Control Expert, Ethernet Network
Modules, User Manual)

35010574 12/2018 189

140 NOE xxx xx: Ethernet Module General Overview

Service -00 -01 -10 -11 NWM

Schneider Private MIB (see Quantum using X X X
EcoStruxure™ Control Expert, Ethernet Network
Modules, User Manual)
FactoryCast Application (see Quantum using X X X
EcoStruxure™ Control Expert, Ethernet Network
Modules, User Manual)
User-programmed Web pages X X X
JAVA Virtual Machine X
Fiber optic connection X X X X
RJ45 connection X X X X
Time Synchronization Service (see Quantum X
using EcoStruxure™ Control Expert, Ethernet
Network Modules, User Manual)
Electronic Mail Notification Service X X
(see Quantum using EcoStruxure™ Control
Expert, Ethernet Network Modules, User Manual)

NOTE: In the detailed description of the key features, only modules in the NOE family are named.
The features are also available for the 140 NWM 100 00 module, depending on the listed
properties in the above table.
NOTE: In Control Expert software, the 140 NWM 100 00 module is set in the TCP/IP Regular
Network family, although it belongs to the TCP/IP FactoryCast network family. So, the services
listed above (I/O scanning, Global Data, address server, Bandwidth monitoring) are not supported
by the module. However, they can be selected in the TCP/IP regular network configuration in
Control Expert. (Even if they are configured, those services won't work with the module.)

190 35010574 12/2018

 140 NOE xxx xx: Ethernet Module General Overview

Maximum Number of Networks Per CPU

The following table summarizes the maximum number of networks per CPU, where "networks"
means the sum of NOE, Modbus+ and any other communication modules:

Modicon Quantum CPU Type Supported Number of Networks

140 CPU 311 10 2
140 CPU 434 12A 6
140 CPU 534 14A 6
140 CPU 651 50 6
140 CPU 651 50 6
140 CPU 652 60 6
140 CPU 658 60 6
140 CPU 670 60 3
140 CPU 671 60 6
140 CPU 672 60 6
140 CPU 672 61 6
140 CPU 678 61 6

Front Panel Components

The front panel of the Ethernet modules contains identification markings, color codes, and LED
displays. A writable area for an IP address, a global address label, and two Ethernet cable
connectors is located behind the removable front panel door.
The following table provides a description of the front panel components that are shown in following
figure:

Component Description
LED Indicator Panel Indicates the operating status of the module, and the fiber optic
(see page 192) or Ethernet communications network to which it is connected.
IP Address Area Provides a writable area to record the module’s assigned IP
address.
Global Address Label Indicates the module’s global Ethernet MAC address assigned
at the factory.
100 BASE-FX Connector Provides an MT-RJ socket for connection to a 100-megabit
fiber-optic Ethernet cable.
10/100 BASE-T Connector Provides an RJ45 socket for connection to a shielded, twisted
pair Ethernet cable.

35010574 12/2018 191

140 NOE xxx xx: Ethernet Module General Overview

Indicators for Ethernet Modules

Illustration
The following figure shows the NOE 771 00 LED indicators as a placeholder for all other Ethernet
modules:

Description
The following table shows the LED descriptions:

LED Color Description

Active Green Indicates the backplane is configured.
Ready Green Indicates module is healthy.
Fault Red Flashes when the NOE is in crash state.
Run Green Flashes to indicate diagnostic code, as described below.
Coll. Red Flashes when Ethernet collisions occur.
Link Green On when Ethernet link is active.
Tx Act Green Flashes to indicate Ethernet transmission.
Rx Act Green Flashes to indicate Ethernet reception.
10MB Green On when the module is connected to a 10-Megabit network.
100MB Green On when the module is connected to a 100-Megabit network.
Fduplex On when Ethernet is operating in the full duplex mode.
Kernel Amber On when in Kernel Mode.
Flashing while in download mode.
Appl Green On when crash log entry exists.

192 35010574 12/2018

 140 NOE xxx xx: Ethernet Module General Overview

Run LED Status

The following table lists each available state of the Run LED indicator and provides diagnostic
information for that state in both the 140 NOE 771x1 module and the 140 NWM 100 module.

Indicator State Status for 140NOE771x1 Status for 140NWM100

On (steady) Normal operation: The NOE Normal operation: The NOE
module is ready for network module is ready for network
communication. communication.
Number of flashes in sequence
1 Not used Not used
2 Not used Not used
3 No Link: the network cable is not No Link: the network cable is not
connected or is defective connected or is defective
4 Duplicate IP address: The module Duplicate IP address: The module
will be set to its default IP address. will stay off-line.
5 No IP address: The module is No IP address: The module is
attempting to obtain an IP address attempting to obtain an IP address
from a BOOTP server. Module is from a BOOTP server.
set to its default IP address.
6 Invalid IP configuration. (Likely Using default IP address
cause: Default gateway is not on
the same subnet mask.) Module is
set to its default IP address.
7 No valid executive NOE present No valid executive NOE present
8 Not used Not used
9 - Flash file system inoperative.

35010574 12/2018 193

140 NOE xxx xx: Ethernet Module General Overview

194 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOE 211 00
35010574 12/2018

Chapter 18
140 NOE 211 x0: TCP/IP 10Base-T Ethernet Module

140 NOE 211 x0: TCP/IP 10Base-T Ethernet Module

Purpose
This chapter contains information of the 140 NOE 211 x0 Module.
NOTE: For detailed information see also Product Related Information, page 14, User Guide for the
Quantum NOE 211/251 Ethernet Module

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 196
Indicators 197
Specifications 198
Installation 199

35010574 12/2018 195

140 NOE 211 00

Presentation

Function
The Ethernet TCP/IP module for twisted pair cabling provides an interface to Ethernet networks for
the Quantum Automation Series system.

Illustration
The following figure shows the Ethernet TCP/IP NOE 211 x0 module.

1 Model Number, Module Description, Color Code

2 LED Display
3 Global Address Label
4 Transmit Cable Connector
5 Receive Cable Connector
6 Removable door
7 Customer Identification Label, (Fold label and place it inside door)

196 35010574 12/2018

 140 NOE 211 00

Indicators

Illustration
The following figure shows the NOE 211 x0 LED indicators.

Description
The following table shows the NOE 211 x0 LED descriptions.

LEDs Color Indication when On

Active Green Module is communicating with backplane.
Ready Green Module has passed internal diagnostic tests.
Run Green Flashes during normal operation.
Link Green Ethernet link to hub is ok.
Kernel Amber If steady, module is operating in kernel mode. If flashing,
module is waiting for download.
Fault Red An error has been detected, a download has failed or a reset is
in process.
Coll Red If steady, cable is not connected. If flashing, Ethernet collisions
are occurring.
Appl Amber Entry exists in crash log.

35010574 12/2018 197

140 NOE 211 00

Specifications

Specifications Table
Specifications Table

Power Dissipation 5W
Bus Current required 1A
Protocol Ethernet ports transmit and receive Modbus commands
encapsulated in TCP/IP protocol.
Ports One 10BASE-T Ethernet network (RJ-45) port.
Data Transfer Frequency 10 Mbps
Compatibility with All, V2.0 at a minimum
Quantum Controllers
Factory Cast 140 NOE 211 10 only

198 35010574 12/2018

 140 NOE 211 00

Installation

Installing the NOE Module

Quantum Ethernet TCP/IP modules come fully configured. However, before installing your module,
you should make sure the default configuration is appropriate for your network.
If the module will be communicating on an open network, consult your network administrator to
obtain a unique IP network address. You must enter this address in the Modsoft Ethernet TCP/IP
configuration extension screen before installing the module.
If the module will be communicating on a local network, make sure the default IP network address
is not already in use on that network. To determine the default IP network address, locate the
global address label on the front panel of the module. Convert the rightmost eight digits from
hexadecimal to decimal. The result should be a decimal number in the form, 84.xxx.xxx.xxx, where
each group of xxx is a number from 0 to 255. This is the default IP network address.

35010574 12/2018 199

140 NOE 211 00

Installation Example
The following example shows the steps for discovering the default IP network address.

Step Action
1 Locate the global address label on the front panel of the module.

2 Note the rightmost eight digits.

3 Convert them from hexadecimal to decimal. Each pair of hexadecimal numbers

will result in a decimal number between 0 and 255. This is the default IP address.
4 If you use the default IP network address and if your network uses Ethernet II
framing and if you do not need to specify the default gateway or a subnet mask,
then you may install the module without changing the default configuration.

CAUTION
UNEXPECTED EQUIPMENT BEHAVIOR
Do not connect this module to your network until you have ensured that its IP
address will be unique on the network.
Failure to follow these instructions can result in injury or equipment damage.

CAUTION
UNEXPECTED EQUIPMENT BEHAVIOR
The cable for an Ethernet module must be routed through an Ethernet hub for the
network to function properly. Do not connect the module directly to another device.
Failure to follow these instructions can result in injury or equipment damage.

200 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOE 251 00
35010574 12/2018

Chapter 19
140 NOE 251 x0: TCP/IP 10Base-FL Ethernet Module

140 NOE 251 x0: TCP/IP 10Base-FL Ethernet Module

Purpose
This chapter contains information of the 140 NOE 251 x0 Module.
NOTE: For detailed information see also Product Related Information, page 14, User Guide for the
Quantum NOE 211/251 Ethernet Module

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 202
Indicators 203
Specifications 204
Installation 205

35010574 12/2018 201

140 NOE 251 00

Presentation

Function
The Ethernet TCP/IP modules for fiber optic cabling provide an interface to Ethernet networks for
the Quantum Automation Series system.

Illustration
The following figure shows the Ethernet TCP/IP NOE 251 x0 module.

1 Model Number, Module Description, Color Code

2 LED Display
3 Global Address Label
4 Transmit Cable Connector
6 Receive Cable Connector
5 Removable door
6 Customer Identification Label, (Fold label and place it inside door)

202 35010574 12/2018

 140 NOE 251 00

Indicators

Illustration
The following figure shows the NOE 251 x0 LED indicators.

Description
The following table shows the NOE 251 x0 LED descriptions.

LEDs Color Indication when On

Active Green Module is communicating with backplane.
Ready Green Module has passed internal diagnostic tests.
Run Green Flashes during normal operation.
Link Green Ethernet link to hub is ok.
Kernel Amber If steady, module is operating in kernel mode. If flashing,
module is waiting for download.
Fault Red An error has been detected, a download has failed or a reset is
in process.
Coll Red If steady, cable is not connected. If flashing, Ethernet collisions
are occurring.
Appl Amber Entry exists in crash log.

35010574 12/2018 203

140 NOE 251 00

Specifications

Specifications Table
Specifications Table

Power Dissipation 5W
Bus Current required 1A
Protocol Ethernet ports transmit and receive Modbus commands
encapsulated in TCP/IP protocol
Ports One 10BASE-FL Ethernet network (ST-style) port.
Data Transfer Frequency 10 Mbps
Compatibility with All, V2.0 at a minimum
Quantum Controllers
Factory Cast 140 NOE 251 10 only

204 35010574 12/2018

 140 NOE 251 00

Installation

Installing the NOE Module

Quantum Ethernet TCP/IP modules come fully configured. However, before installing your module,
you should make sure the default configuration is appropriate for your network.
If the module will be communicating on an open network, consult your network administrator to
obtain a unique IP network address. You must enter this address in the Modsoft Ethernet TCP/IP
configuration extension screen before installing the module.
If the module will be communicating on a local network, make sure the default IP network address
is not already in use on that network. To determine the default IP network address, locate the
global address label on the front panel of the module. Convert the rightmost eight digits from
hexadecimal to decimal. The result should be a decimal number in the form, 84.xxx.xxx.xxx, where
each group of xxx is a number from 0 to 255. This is the default IP network address.

35010574 12/2018 205

140 NOE 251 00

Installation Example
The following example shows the steps for discovering the default IP network address.

Step Action
1 Locate the global address label on the front panel of the module.

2 Note the rightmost eight digits.

3 Convert them from hexadecimal to decimal. Each pair of hexadecimal numbers

will result in a decimal number between 0 and 255. This is the default IP address.
4 If you use the default IP network address and if your network uses Ethernet II
framing and if you do not need to specify the default gateway or a subnet mask,
then you may install the module without changing the default configuration.

CAUTION
UNEXPECTED EQUIPMENT BEHAVIOR
Do not connect this module to your network until you have ensured that its IP
address will be unique on the network.
Failure to follow these instructions can result in injury or equipment damage.

CAUTION
UNEXPECTED EQUIPMENT BEHAVIOR
The cable for an Ethernet module must be routed through an Ethernet hub for the
network to function properly. Do not connect the module directly to another device.
Failure to follow these instructions can result in injury or equipment damage.

206 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOE 311 00
35010574 12/2018

Chapter 20
140 NOE 311 00: SY/MAX 10Base-T Ethernet Module

140 NOE 311 00: SY/MAX 10Base-T Ethernet Module

Purpose
This chapter contains information of the 140 NOE 311 00 Module.
NOTE: For detailed information see also Product Related Information, page 14, Quantum Sy/Max
Ethernet Network Option Module Guide

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 208
Indicators 210
Specifications 211

35010574 12/2018 207

140 NOE 311 00

Presentation

Function
The Quantum SY/MAX Ethernet module for twisted pair cabling provides an interface for the
Quantum Automation Series system to SY/MAX devices via Ethernet.

Illustration
The following figure shows the NOE 311 00 SY/MAX Ethernet module.

1 Model Number, Module Description, Color Code

2 LED Display
3 Global Address Label
4 RJ-45 Connector
5 Removable door
6 Customer Identification Label, (Fold label and place it inside door)

208 35010574 12/2018

 140 NOE 311 00

SY/MAX Addressing
Be sure that the module is assigned a unique SY/MAX drop number during configuration.

WARNING
UNEXPECTED APPLICATION BEHAVIOR
Do assign a unique SY/MAX drop number during configuration.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

35010574 12/2018 209

140 NOE 311 00

Indicators

Illustration
The following figure shows the NOE 311 00 LED indicators.

Description
The following figure shows the NOE 311 00 LED descriptions.

LEDs Color Indication when On

Active Green Module is communicating with backplane.
Ready Green Module has passed internal diagnostic tests.
Run Green Flashes during normal operation.
Link Green Ethernet connection is made.
Kernel Amber On during download.
Fault Red An error condition has occurred.
Collision Red If steady, an error condition exists. If flashing, packet
collisions are occurring on the network during data
transmission.
Appl Amber A fatal error has occurred.

210 35010574 12/2018

 140 NOE 311 00

Specifications

General Specification
General Specification

Bus Current required 1A

Communication Port One 10BASE-T Ethernet network (RJ45) port.
Backplane Compatibility 3, 4, 6, 10, and 16 position backplanes
(Requires Quantum CPU)
Compatibility SY/MAX Model 450
802.3 Devices and Model 650
Software SFI160
SFW390-VAX
Streamline Version 1.3

Cable Type
Cable Type

10Base-2 or ThinWire 2, 3, 4, or 6 twisted pairs with a solid copper core

Ethernet
10Base-T (twisted pair) RG58a/u or RG58C/U coaxial (Belden 9907/82907 or
equivalent)

Wire Size
Wire Size

10Base-2 or ThinWire 20 AWG

Ethernet
10Base-T (twisted pair) 22, 24, 26 AWG

Topology
Topology

10Base-2 or ThinWire Bus

Ethernet
10Base-T (twisted pair) Star

35010574 12/2018 211

140 NOE 311 00

Connector
Connector

10Base-2 or ThinWire BNC (UG-274)

Ethernet
10Base-T (twisted pair) Modular RJ-45 (4 pins of 8 are used by 10Base- T

212 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOE 351 00
35010574 12/2018

Chapter 21
140 NOE 351 00: SY/MAX 10Base-FL Ethernet Module

140 NOE 351 00: SY/MAX 10Base-FL Ethernet Module

Purpose
This chapter contains information of the 140 NOE 351 00 Module.
NOTE: For detailed information see also Product Related Information, page 14, Quantum Sy/Max
Ethernet Network Option Module Guide

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 214
Indicators 216
Specifications 217

35010574 12/2018 213

140 NOE 351 00

Presentation

Function
The Quantum SY/MAX Ethernet module for fiber optic cabling provides an interface for the
Quantum Automation Series system to SY/MAX devices via Ethernet.

Illustration
The following figure shows the NOE 351 00 SY/MAX Ethernet module.

1 Model Number, Module Description, Color Code

2 LED Display
3 Global Address Label
4 Transmit Cable Connector
5 Receive Cable Connector
6 Removable door
7 Customer Identification Label, (Fold label and place it inside door)

214 35010574 12/2018

 140 NOE 351 00

SY/MAX Addressing
Be sure that the module is assigned a unique SY/MAX drop number during configuration.

WARNING
UNEXPECTED APPLICATION BEHAVIOR
Do assign a unique SY/MAX drop number during configuration.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

35010574 12/2018 215

140 NOE 351 00

Indicators

Illustration
The following figure shows the NOE 351 00 LED indicators.

Description
The following figure shows the NOE 351 00 LED descriptions.

LEDs Color Indication when On

Active Green Module is communicating with backplane.
Ready Green Module has passed internal diagnostic tests.
Run Green Flashes during normal operation.
Link Green Ethernet connection is made.
Kernel Amber On during download.
Fault Red An error condition has occurred.
Collision Red If steady, an error condition exists. If flashing, packet
collisions are occurring on the network during data
transmission.
Appl Amber A fatal error has occurred.

216 35010574 12/2018

 140 NOE 351 00

Specifications

General Specification
General Specification

Bus Current required 1A

Communication Port Two 10BASE-FL Ethernet network (ST-style) port.
Backplane Compatibility 3, 4, 6, 10, and 16 position backplanes
(Requires Quantum CPU)
Compatibility SY/MAX Model 450
802.3 Devices and Model 650
Software SFI160
SFW390-VAX
Streamline Version 1.3

35010574 12/2018 217

140 NOE 351 00

218 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOE 771 00
35010574 12/2018

Chapter 22
140 NOE 771 00: TCP/IP 10/100 Ethernet Module

140 NOE 771 00: TCP/IP 10/100 Ethernet Module

Purpose
This chapter contains information of the 140 NOE 771 00 Module.
NOTE: For detailed information see also Product Related Information, page 14, User Guide for the
Quantum NOE 771 Ethernet Module

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 220
Indicators 223
Specifications 224

35010574 12/2018 219

140 NOE 771 00

Presentation

Function
The Quantum 140 NOE 771 00,10/100 Ethernet module is the latest model in a line of Quantum
Ethernet TCP/IP modules designed to make it possible for a Quantum Programmable Logic
Controller (PLC) to communicate with devices over an Ethernet network.

220 35010574 12/2018

 140 NOE 771 00

Illustration
The following figure shows the front of the NOE 771 00 Ethernet module.

1 Model Number, Module Description, Color Code

2 LED Display
3 IP Address Writable Area
4 Global Address Label
5 100 Base Fx MT-RJ Cable Connector
6 10/100 Base-T RJ-45 Cable Connector
7 Removable door

35010574 12/2018 221

140 NOE 771 00

Front Panel Components

The front panel of the NOE 771 00 module contains identification marking, color code, and LED
display. A writable area for an Internet Protocol (IP) address, a global address label, and two
Ethernet cable connectors is located behind the removable front panel door.
The following table provides a description of the front panel components which are shown in front
view figure.

Component Description
LED indicator Panel Indicates the operating status of the module, and the fiber optic and
Modbus communications networks it is connected to. (See
Indicators, page 223)
IP Address Writable Provides a writable area to record the module’s assigned IP
Area address.
Global Address Label Indicates the module’s global Ethernet MAC address assigned at
the factory.
100 BASE-FX Provides an MT-RJ receptacle for connection to a 100 megabit fiber
Connector optic Ethernet cable.
10/100BASE-T Provides an RJ-45 receptacle for connection to a shielded, twisted
Connector pair Ethernet cable.

222 35010574 12/2018

 140 NOE 771 00

Indicators

Illustration
The following figure shows the 140 NOE 771 00 LED indicators.

Description
The following table shows the 140 NOE 771 00 LED descriptions.

LEDs Color Indication when On

Active Green Module is communicating with backplane.
Ready Green Module has passed internal diagnostic tests.
Run Green Flashes during normal operation.
Link Green Ethernet link to hub is ok.
Kernel Amber If steady, module is operating in kernel mode. If flashing,
module is waiting for download.
Fault Red An error has been detected, a download has failed or a reset is
in process.
Coll Red If steady, cable is not connected. If flashing, Ethernet collisions
are occurring.
Appl Amber Entry exists in crash log.

35010574 12/2018 223

140 NOE 771 00

Specifications

Specifications Table
Specifications Table

Power Dissipation 3.8 W

Bus Current required 750 mA
Protocol Ethernet ports transmit and receive Modbus commands
encapsulated in TCP/IP protocol
Ports One 100 BASE-FX Fiber optics (MT-RJ) port.
One 10/100BASE-T (RJ-45) port.
Fuse none
Factory Cast no
I/O Scanner yes

224 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOE 771 01
35010574 12/2018

Chapter 23
140 NOE 771 01: TCP/IP 10/100 Ethernet Module

140 NOE 771 01: TCP/IP 10/100 Ethernet Module

Purpose
This chapter contains information of the 140 NOE 771 01 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 226
Indicators 227
Specifications 229

35010574 12/2018 225

140 NOE 771 01

Presentation

Function
The Ethernet TCP/IP module for twisted pair cabling provides an interface to Ethernet networks for
the Quantum Automation Series system.

Illustration
The following figure shows the Ethernet TCP/IP 140 NOE 771 01 module.

1 model number, module description, color code

2 LED display
3 global address label
4 MT-RJ fiber optic connector
5 RJ-45 connector
6 removable door

226 35010574 12/2018

 140 NOE 771 01

Indicators

Illustration
The following figure shows the 140 NOE 771 01 LED indicators.

Description
The following table shows the 140 NOE 771 01 LED descriptions.

LEDs Color Indication when On

Active Green Module is communicating with backplane.
Ready Green Module has passed internal diagnostic tests.
Run Green Flashes during normal operation.
Link Green Ethernet link to hub is ok.
Kernel Amber If steady, module is operating in kernel mode. If flashing, module is
waiting for download.
Fault Red An error has been detected, a download has failed or a reset is in
process.
Coll Red If steady, cable is not connected. If flashing, Ethernet collisions are
occurring.
Appl Amber Entry exists in crash log.

35010574 12/2018 227

140 NOE 771 01

Run LED Status

The following table lists each available state of the run LED indicator and provides diagnostic
information for that state.

Indicator State Status

On (steady) Normal operation: The NOE module is ready for network communication.
Number of flashes in sequence
one Not used
two Not used
three No link. The network cable is not connected or is defective.
four Duplicate IP address. The module is set to its default IP address.
five No IP address. The module is attempting to obtain an IP address from a
BootP server. The module is set to its default IP address.
six Invalid IP configuration. (Likely cause: Default gateway is not on the same
subnet mask. The module is set to its default IP address.)
seven No valid executive NOE is present.

228 35010574 12/2018

 140 NOE 771 01

Specifications

Specifications Table
Specifications Table

Power Dissipation 3.8 W

Bus Current required 750 mA
Protocol Ethernet ports transmit and receive Modbus commands
encapsulated in TCP/IP protocol.
Ports One 100 BASE-FX Fiber optics (MT-RJ) port.
One 10/100BASE-T (RJ-45) port.
Compatibility with All, V2.0 at a minimum
Quantum Controllers
Factory Cast no
I/O Scanner yes

35010574 12/2018 229

140 NOE 771 01

230 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOE 771 10
35010574 12/2018

Chapter 24
140 NOE 771 10: TCP/IP 10/100 FactoryCast Ethernet Module

140 NOE 771 10: TCP/IP 10/100 FactoryCast Ethernet Module

Purpose
This chapter contains information about the 140 NOE 771 10 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 232
Indicators 235
Specifications 237

35010574 12/2018 231

140 NOE 771 10

Presentation

Function
The Quantum 140 NOE 771 10,10/100 Ethernet module is the latest model in a line of Quantum
Ethernet TCP/IP modules designed to make it possible for a Quantum Programmable Logic
Controller (PLC) to communicate with devices over an Ethernet network.

232 35010574 12/2018

 140 NOE 771 10

Illustration
The following figure shows the front of the NOE 771 10 Ethernet module.

1 Model Number, Module Description, Color Code

2 LED Display
3 IP Address Writable Area
4 Global Address Label
5 100 Base Fx MT-RJ Cable Connector
6 10/100 Base-T RJ-45 Cable Connector
7 Removable door

35010574 12/2018 233

140 NOE 771 10

Front Panel Components

The front panel of the NOE 771 10 module contains identification marking, color code, and LED
display. A writable area for an Internet Protocol (IP) address, a global address label, and two
Ethernet cable connectors is located behind the removable front panel door.
The following table provides a description of the front panel components which are shown in front
view figure.

Component Description
LED indicator Panel Indicates the operating status of the module, and the fiber optic and
Modbus communications networks it is connected to. (See
Indicators in this
IP Address Writable Provides a writable area to record the module’s assigned IP
Area address.
Global Address Label Indicates the module’s global Ethernet MAC address assigned at
the factory.
100 BASE-FX Provides an MT-RJ receptacle for connection to a 100 Megabit fiber
Connector optic Ethernet cable.
10/100BASE-T Provides an RJ-45 receptacle for connection to a shielded, twisted
Connector pair Ethernet cable.

234 35010574 12/2018

 140 NOE 771 10

Indicators

Illustration
The following figure shows the NOE 771 10 LED indicators.

Description
The following table shows the NOE 771 10 LED descriptions.

LED Color Description

Active Green Indicates the backplane is configured.
Ready Green Indicates module is healthy.
Fault Red Flashes when Ethernet collisions occur.
Run Green Flashes to indicate diagnostic code, as described in
"Run LED Status" (below).
Coll. Red Flashes when Ethernet collisions occur.
Link Green On when Ethernet link is active.
Tx Act Green Flashes to indicate Ethernet transmission.
Rx Act Green Flashes to indicate Ethernet reception.
Kernel Amber On when in Kernel Mode.
10MB Green On when the module is connected to a 10 Megabit
network.
100MB Green
Fduplex On when Ethernet is operating in the full duplex mode.
Appl Green On when crash log entry exists.

35010574 12/2018 235

140 NOE 771 10

Run LED Status

The following table lists each available state of the Run LED indicator, and it provides diagnostic
information for that state

Indicator State Status

On (steady) Normal operation: The NOE module is ready for network
communication.
Number of flashes in sequence
one Not used
two Not used
three No Link: the network cable is not connected or is defective
four Duplicate IP address: The module will stay off-line.
five No IP address: The module is attempting to obtain an IP
address from a BOOTP server.
six Using default IP address
seven No valid executive NOE present

236 35010574 12/2018

 140 NOE 771 10

Specifications

Specifications Table
Specifications Table

Power Dissipation 3.8 W

Bus Current required 750 mA
Protocol Ethernet ports transmit and receive Modbus commands
encapsulated in TCP/IP protocol
Ports One 100 BASE-FX Fiber optics (MT-RJ) port.
One 10/100BASE-T (RJ-45) port.
Fuse none
Factory Cast yes
I/O Scanner no

35010574 12/2018 237

140 NOE 771 10

238 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NOE 771 11
35010574 12/2018

Chapter 25
140 NOE 771 11: TCP/IP 10/100 FactoryCast Ethernet Module

140 NOE 771 11: TCP/IP 10/100 FactoryCast Ethernet Module

Purpose
This chapter contains information about the 140 NOE 771 11 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 240
Indicators 241
Specifications 243

35010574 12/2018 239

140 NOE 771 11

Presentation

Function
The Ethernet TCP/IP module for twisted pair cabling provides an interface to Ethernet networks for
the Quantum Automation Series system.

Illustration
The following figure shows the Ethernet TCP/IP 140 NOE 771 11 module.

1 model number, module description, color code

2 LED display
3 global address label
4 MT-RJ fiber optic connector
5 RJ-45 connector
6 removable door

240 35010574 12/2018

 140 NOE 771 11

Indicators

Illustration
The following figure shows the 140 NOE 771 11 LED indicators.

Description
The following table shows the 140 NOE 771 11 LED descriptions.

LEDs Color Indication when On

Active Green Module is communicating with backplane.
Ready Green Module has passed internal diagnostic tests.
Run Green Flashes during normal operation.
Link Green Ethernet link to hub is ok.
Kernel Amber If steady, module is operating in kernel mode. If flashing, module is
waiting for download.
Fault Red An error has been detected, a download has failed or a reset is in
process.
Coll Red If steady, cable is not connected. If flashing, Ethernet collisions are
occurring.
Appl Amber Entry exists in crash log.

35010574 12/2018 241

140 NOE 771 11

Run LED Status

The following table lists each available state of the run LED indicator and provides diagnostic
information for that state.

Indicator State Status

On (steady) Normal operation: The NOE module is ready for network communication.
Number of flashes in sequence
one Not used
two Not used
three No link. The network cable is not connected or is defective.
four Duplicate IP address. The module is set to its default IP address.
five No IP address. The module is attempting to obtain an IP address from a
BootP server. The module is set to its default IP address.
six Invalid IP configuration. (Likely cause: Default gateway is not on the same
subnet mask. The module is set to its default IP address.)
seven No valid executive NOE is present.

242 35010574 12/2018

 140 NOE 771 11

Specifications

Specifications Table
Specifications Table

Power Dissipation 3.8 W

Bus Current required 750 mA
Protocol Ethernet ports transmit and receive Modbus commands
encapsulated in TCP/IP protocol.
Ports One 100 BASE-FX Fiber optics (MT-RJ) port.
One 10/100BASE-T (RJ-45) port.
Compatibility with All, V2.0 at a minimum
Quantum Controllers
Factory Cast yes
I/O Scanner yes

35010574 12/2018 243

140 NOE 771 11

244 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 NWM 100 00
35010574 12/2018

Chapter 26
140 NWM 100 00: TCP/IP 10/100 FactoryCast HMI Ethernet Module

140 NWM 100 00: TCP/IP 10/100 FactoryCast HMI Ethernet

Module

Purpose
This chapter contains information about the 140 NWM 100 00 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 246
Indicators 247
Specifications 248

35010574 12/2018 245

140 NWM 100 00

Presentation

Function
The Ethernet TCP/IP module for twisted pair cabling provides an interface to Ethernet networks for
the Quantum Automation Series system.

Illustration
The following figure shows the Ethernet TCP/IP 140 NWM 100 00 module.

1 Model Number, Module Description, Color Code

2 LED Display
3 IP Address Writable Area
4 Global Address Label
5 100 Base Fx MT-RJ Cable Connector
6 10/100 Base-T RJ-45 Cable Connector
7 Removable door

246 35010574 12/2018

 140 NWM 100 00

Indicators

Illustration
The following figure shows the 140 NWM 100 00 LED indicators.

Description
The following table shows the 140 NWM 100 00 LED descriptions.

LEDs Color Indication when On

Active Green Module is communicating with backplane.
Ready Green Module has passed internal diagnostic tests.
Run Green Flashes during normal operation.
Link Green Ethernet link to hub is ok.
Kernel Amber If steady, module is operating in kernel mode. If flashing,
module is waiting for download.
Fault Red An error has been detected, a download has failed or a reset is
in process.
Coll Red If steady, cable is not connected. If flashing, Ethernet collisions
are occurring.
Appl Amber Entry exists in crash log.

35010574 12/2018 247

140 NWM 100 00

Specifications

Specifications Table
Specifications Table

Power Dissipation 4.5 W

Bus Current required 900 mA
Protocol Ethernet ports transmit and receive Modbus commands
encapsulated in TCP/IP protocol.
Ports One 100 BASE-FX Fiber optics (MT-RJ) port.
One 10/100BASE-T (RJ-45) port.
Compatibility with All, V2.0 at a minimum
Quantum Controllers
Factory Cast yes
I/O Scanner no

248 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
Field Bus Modules
35010574 12/2018

Part VI
Quantum Field Bus Modules

Quantum Field Bus Modules

35010574 12/2018 249

Field Bus Modules

250 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 EIA 921 00
35010574 12/2018

Chapter 27
140 EIA 921 00: AS-i Master Communication Module

140 EIA 921 00: AS-i Master Communication Module

Purpose
This chapter contains information on the 140 EIA 921 00 AS-i master communications module.
NOTE: For detailed information see also Product Related Information, page 14, Modicon Quantum
AS-i Master Module EIA 921 00

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 252
Indicators 255
Wiring Diagram 257
Specifications 258
Parameter Configuration 259

35010574 12/2018 251

140 EIA 921 00

Presentation

Function
The Quantum AS-i Master Module provides AS-i communications between the bus master module
and the sensor/actuator slaves. One master module can control 31 slaves. Multiple master
modules can be used in a single control system.
These sensor/actuators can be in the local CPU, an RIO, or a DIO drop adapter.
NOTE: This module is not available to directly exploit analog slaves (profile 7.1, 7.2, 7.3, 7.4) on
an AS-i bus.
For detailed information see Modicon Quantum AS-i Master Module EIA 921 00 book Product
Related Information, page 14

252 35010574 12/2018

 140 EIA 921 00

Illustration
Front view of the AS-i module with LED Matrix detail and legend numbers:

35010574 12/2018 253

140 EIA 921 00

Legend
The following table provides a description of the functions of the equipment LEDs.

Item Description
1 Display block comprising 4 status indicator lamps (LEDs) for displaying the
module operating modes:
 B (green, 1 LED): Indicates, when on, data exchange between module and
slave.
 Active (green, 2 LEDs): when on, indicates AS-i module being services by
the local CPU, RIO, or DIO drop adapter.
 F (red, 1 LED): indicates, when on steady, module fault. Flashing shows
external I/O fault (could indicate slave with address 0 or an AS-i bus
configuration fault.
2 Display block of 32 indicator lamps (0 - 31, green) for diagnostics of the AS-i bus
and display of the state of each slave connected to the bus.
3 AS-i (red): ON shows AS-i line not properly powered. Flashing shows automatic
addressing enabled and a slave is "prévu" but not connected. OFF shows
normal module function.
4 SLV/BUS (green): ON shows the LEDs 0-31 are in BUS display mode. Displays
the slaves on the bus.
5 I/O Status (green): On shows the LEDs 0-31 are in SLV display mode. Displays
the state of a selected slave.
6 Mode (Push Button): provides local diagnostics of the AS-i bus. Press this
button longer than 1 sec. to change the mode. In slave mode use the Address
Push Button to scroll among the 32 addresses.
7 Address (Push Button): Pressing this button (in slave mode) scrolls through the
slaves. Press longer than 1 sec. to reverse direction of the scroll.
8 AS-i Channel cable connector - connects module to AS-i cable and AS-i power
supply.

254 35010574 12/2018

 140 EIA 921 00

Indicators

Ilustration
Diagram of the LED display:

Description

LED Color Description

Active Green Bus communication is present.
F Red Fault on the AS-i bus.
Steady: module fault
Flashing: bad bus configuration or slave address
B Green Communication exists between master and slaves.
0-31 Green Slave indicators.

Each indicator lamp 1-31 corresponds to a slave address on the bus.

 On: Slave is present.
 Flashing: Slave is mapped but not detected, or detected but not mapped. It may also be
projected and detected, but not activated (bad profile or I/O code).
 Off: Slave is neither mapped nor detected.
Example:

35010574 12/2018 255

140 EIA 921 00

LED Slave I/O Status

Slave mode (SLV) figure:

LED Diagnostics
State of Indicator Lamps:

B Active F Meaning Corrective Action

Module switched off. Switch the device on.

Operating in Protected æ
Mode (normal). Displaying
Outputs.
Operating in Protected æ
Mode (normal). Displaying
Inputs.
Fault on AS-i bus (self- Replace the faulty slave with a
programming possible). new identical slave.

Fault on AS-i bus (self- Connect the terminal.

programming not possible).

AS-i power supply fault or 1. Check AS-i power supply.

no slave on the AS-i bus. 2. Check the continuity of the
AS-i bus cable.
Module self-tests in æ
progress.

Indicator lamp Indicator Indicator lamp is Indicator lamp is in

is on. lamp is off. flashing. indeterminate state.
(1) Faulty slave ID is flashing.
(2) No slave ID numbers are flashing.

256 35010574 12/2018

 140 EIA 921 00

Wiring Diagram

AS-i Cable Connection

Diagram for the AS-i cable connection

35010574 12/2018 257

140 EIA 921 00

Specifications

AS-i Specifications
Specifications for the 140 EIA 921 00 AS-i module:

Master profile M2
Bus length 100m max, no repeaters
I/O 124 IN / 124 OUT
# slaves 31 max.
Power supply 30VDC @ 120mA max.
Scan time 156 msec x (n+2) if n < 31
156 msec x (n+1) if n = 31
Transmission 167 kbits/sec
Polarity reversal Non-destructive
Bus current required 250mA max.
Power dissipation 2.5W max.
Installation Local, RIO, DIO

258 35010574 12/2018

 140 EIA 921 00

Parameter Configuration

Parameter and Default Values

Parameter Configuration Window

Name Default Value Options Description

MAPPING WORD (%IW-3x
%MW-4X)
INPUTS STARTING 1 1-65522 Address area where the input information from the
ADDRESS AS-i modules is mapped
INPUTS ENDING 13
ADDRESS
OUTPUTS STARTING 1 1-65526 Address area where the output information to the
ADDRESS AS-i modules is mapped
OUTPUTS ENDING 9
ADDRESS

35010574 12/2018 259

140 EIA 921 00

Name Default Value Options Description

TASK MAST FAST Fixed to MAST if module in other than local
(Grayed if module in AUX0
other than local) AUX1
AUX2
AUX3
OPERATING MODE Protected Configuration Configuration Mode: all slaves are activated, i.e.
writing on outputs as well as reading from inputs is
done directly.
Protected Mode: Only those slaves with a
configuration on the AS-i bus which matches the
reference configuration are activated.
TIMEOUT STATE Fallback to 0 HOLD LAST Determines the state of the I/O points in case of an
VALUE communication error
AUTOMATIC SLAVE 0 Disable Enable When this function is enabled a faulty slave can be
ADDRESSING replaced by a slave of the same type without
stopping the AS-i bus.
AS-i SLAVE CONFIGURATION
AS-i SLAVE 1
PROJECT No Yes When "Yes", the configuration is downloaded to
the slave and the slave is added to the list of
configured slaves
IO PROFILE 0 Refer to indications of the slave manufacturer
ID PROFILE 0 about slave profiles and capabilities.

PARAMETERS 0
AS-i SLAVE 2-31 see AS-i SLAVE 1

260 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
Special Purpose / Intelligent Modules
35010574 12/2018

Part VII
Quantum Special Purpose / Intelligent Modules

Quantum Special Purpose / Intelligent Modules

Introduction
This part provides information of the Quantum Special Purpose / Intelligent Modules

What Is in This Part?

This part contains the following chapters:
Chapter Chapter Name Page
28 140 HLI 340 00: High Speed Latch and Interrupt Module 263
29 140 EHC 202 00: High Speed Counter Module 273
30 140 EHC 105 00: High Speed Counter Module 317

35010574 12/2018 261

Special Purpose / Intelligent Modules

262 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 HLI 340 00
35010574 12/2018

Chapter 28
140 HLI 340 00: High Speed Latch and Interrupt Module

140 HLI 340 00: High Speed Latch and Interrupt Module

Purpose
The following chapter provides information of the Quantum 140 HLI 340 00 Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 264
Indicators 265
Specifications 266
Wiring Diagram 268
Addressing 270
Parameter Configuration 271

35010574 12/2018 263

140 HLI 340 00

Presentation

Function
The High Speed Latch and Interrupt 24 VDC 16x1 Sink / Source input module accepts 24 VDC
inputs and is for use with 24 VDC sink/source input devices.

Illustration
The following figure shows the 140 HLI 340 00 module and its components.

1 Model Number, Module Description, Color Code

2 LED Display
3 Field Wiring Terminal Strip
4 Removable Door
5 Customer Identification Label (Fold label and place it inside door)

NOTE: The field wiring terminal strip (Modicon #140 XTS 002 00) must be ordered separately. (The
terminal strip includes the removable door and label.)
NOTE: The tightening torque must be between 0.5 Nm and 0.8 Nm.

NOTICE
DESTRUCTION OF ADAPTER
 Before tightening the locknut to the torque 0.50...0.80 Nm, be sure to properly position the
right-angle F adapter connector.
 During tightening, be sure to maintain the connector securely.
 Do not tighten the right-angle F adapter beyond the specified torque.
Failure to follow these instructions can result in equipment damage.

264 35010574 12/2018

 140 HLI 340 00

Indicators

Illustration
The following table shows the LED indicators for the 140 HLI 340 00 module.

Descriptions
The following table shows the LED descriptions for the 140 HLI 340 00 module.

LEDs Color Indication when ON

Active Green Bus communication is present.
1 ... 16 Green The indicated point or channel is turned ON.

NOTE: Due to the speed of the module, LED indications do not represent the state of the input
signal, when the input signal is a short duration pulse.

35010574 12/2018 265

140 HLI 340 00

Specifications

General Specifications
General Specifications

Module Type 16 IN individually isolated

External Power Not required for this module
Power Dissipation 2.0 W/0.30 W x the number of points ON
Bus Current required 400 mA
I/O map 1 input word
Fault Detection None

Indicators
Indicators

LEDs Active 1...16 (green)-indicates point status

Operating Voltage and Input Current

Operating Voltage and Input Current

ON (voltage) 15...30 Vdc

OFF (voltage) -3...+5 Vdc
ON (current) 2.0...8.0 mA
OFF (current) 0...0.5 mA

Maximum Input
Absolute Maximum Input Voltage

Continuous 30 Vdc

Input Protection
Input Protection

30 Vdc reverse polarity (diode protection)

266 35010574 12/2018

 140 HLI 340 00

Isolation
Isolation

Point to Point 500 Vac rms for 1 minute

Point to Bus 1780 Vac rms for 1 minute

Response
Response

OFF - ON 30 μs (max)
ON - OFF 130 μs (max)

Fuses
Fuses

Internal None
External User discretion

Module Keying
Field Wiring Terminal Strip/Module Keying

Module Coding ABE

Terminal Strip Coding CDF

35010574 12/2018 267

140 HLI 340 00

Wiring Diagram

Illustration

268 35010574 12/2018

 140 HLI 340 00

NOTE: Either shielded or unshielded signal cables may be used (the user should consider using
shielded wire in a noisy environment). Shielded types should have a shield tied to earth ground
near the signal ground.
N / C = Not Connected.
NOTE: The tightening torque must be between 0.5 Nm and 0.8 Nm.

NOTICE
DESTRUCTION OF ADAPTER
 Before tightening the locknut to the torque 0.50...0.80 Nm, be sure to properly position the
right-angle F adapter connector.
 During tightening, be sure to maintain the connector securely.
 Do not tighten the right-angle F adapter beyond the specified torque.
Failure to follow these instructions can result in equipment damage.

35010574 12/2018 269

140 HLI 340 00

Addressing

Flat Addressing
This module requires either 16 contiguous %I references or one %IW word. For a description of
how to access the input points, please refer to Discrete I/O Bit Numbering, page 28.

Topological Addressing
The following tables show the topological addresses for the 140HLI34000 module.
Topological addresses in Bit Mapping format:

Point I/O Object Comment

Input 1 %I[\b.e\]r.m.1 Value
Input 2 %I[\b.e\]r.m.2 Value
•••
Input 15 %I[\b.e\]r.m.15 Value
Input 16 %I[\b.e\]r.m.16 Value

Topological addresses in Word Mapping format:

Point I/O Object Comment

Inputword 1 %IW[\b.e\]r.m.1.1 Value

Used abbreviations: b = bus, e = equipment (drop), r = rack, m = module slot.

I/O Map Status Byte

There is no I/O map status byte associated with this module.

270 35010574 12/2018

 140 HLI 340 00

Parameter Configuration

Module Placement
The 140 HLI 340 00 High Speed Interrupt module’s functionality depends on its location.
The following list shows the available modes depending on the location:
 Local Rack: High Speed Inputs, Latch Inputs, Interrupts,
 Remote Rack: High Speed Inputs.

NOTE: The 140 HLI 340 00 module cannot be connected to a secondary rack.

Parameters and Default Values

Parameter Configuration Window

Parameter Description

Name Default Value Options Description

Mapping BIT (%I-1x) WORD (%IW-3X)
Inputs Starting 1
Address
Inputs Ending 16
Address

35010574 12/2018 271

140 HLI 340 00

Name Default Value Options Description

Task MAST FAST
AUX0
AUX1
AUX2
AUX3
Channels
Input n High Speed Input Intp. Rise Edge Interrupt modes
Intp. Fall Edge only available in
Intp. Both Edges local rack, latch
Latch Rise Edge only in local- and
Latch Fall Edge expansion rack
Event n 0 1 - 127

272 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 EHC 202 00
35010574 12/2018

Chapter 29
140 EHC 202 00: High Speed Counter Module

140 EHC 202 00: High Speed Counter Module

Purpose
The following chapter provides information of the Quantum 140 EHC 202 00 High Speed Counter
Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 274
Specifications 276
Controlling and Timing 278
Functions 280
Operating Conditions and Examples 282
Addressing 285
I/O Map and Commands 286
Indicators 303
Wiring 304
Maintenance 311
Parameter Configuration 312

35010574 12/2018 273

140 EHC 202 00

Presentation

Function
The 140 EHC 202 00 is a two-channel module best suited for high-speed counting applications up
to 500 kHz or for applications that require a quadrature counter interface.

Operating Modes
The following operating modes are possible:
 16-bit counters on one or both channels with two outputs, configurable for incremental or
quadrature mode
 32-bit counter that uses both channels with two outputs, configurable for incremental or
quadrature mode
 32-bit counters on one or both channels with no outputs, configurable for incremental or
quadrature mode
 16-bit counters on one or both channels with no outputs, in rate-sample mode for incremental
or quadrature encoders

Outputs
Two FET output switches exist for each counter. They turn on when the counter reaches
programmed setpoint or maximum values in up-count/down-count operations.
The outputs can be turned off by changes in counter values, software commands, or a hard wired
reset from the field.
Each of the outputs can be configured as follows:
 Output latched on at setpoint
 Output latched on at a terminal count
 Output timed on at setpoint, with a time range of 0 ... 16 383 ms (only one of the four possible
outputs can be configured for this mode)
 Output timed on at a terminal count, with a time range of 0 ... 16 383 ms (only one of the four
possible outputs can be configured for this mode)

Inputs
 Single ended or differential

274 35010574 12/2018

 140 EHC 202 00

Illustration
The following figure shows the EHC 102 module and its components.

1 Model Number, Module Description, Color Code

2 LED Display
3 Fuse Cutouts
4 Field Wiring Terminal Strip
5 Removable Door
6 Customer Identification Label (Fold label and place it inside door)

NOTE: The field wiring terminal strip (Modicon #140 XTS 002 00) must be ordered separately. (The
terminal strip includes the removable door and label.)

35010574 12/2018 275

140 EHC 202 00

Specifications

General Specifications
General Specifications

Module Type High Speed Counter Module

Number of Channels 2
External Power 19,2 ... 30 VDC, 24 VDC nominal, 50 mA reqired
plus the load current for each output.
Power Dissipation 4+(0.4 x total modul load current)
Bus Current required 650 mA
I/O Map 6 words IN, 6 words OUT
Isolation (channel to bus) 1780 VAC rms for 1 minute
Fault detection Blown fuse detect; loss of 1A, 1B, 2A, 2B output
field power
Fusing internal: 2.5 (P/N 043503948 or equivalent)
external: user discretion
Backplane Support Local, remote or distributed

Counter Inputs
Counter inputs

Operating mode incremental or quadratur

Input voltage 30 V max. continuous
Data formats 16 bit counter: 65.535 Decimal
32 bit counter: 2.147.483.647 Decimal

Discrete Inputs
Discrete inputs

Operating mode incremental or quadratur

Input voltage 30 V max. continuous
Input resistence 10 kohms

276 35010574 12/2018

 140 EHC 202 00

Input threshold
Input threshold

single ended mode VREF supply On state Off state

5 VREF DC 0 ... 2 V 3.5 ... 5.0 V
12 VREF DC 0 ... 5 V 7 ... 12 V
24 VREF DC 0 ... 11 V 13 ... 24 V
differential mode 1.8 VDC minimum

Discrete Outputs
Discrete outputs

FET Switch ON supply - 0.4 V

FET Switch OFF 0 VDC (ground reference)
Max. load current (each output) 0,5 A
Output off state Leackage 0,4 A max @ 30 VDC
Output on state voltage drop 0.4 VDC @ 0,5 A
Output Levels 1A, 2A, 1B, 2B
Output Protection 36 V transorb for transient voltage suppression

35010574 12/2018 277

140 EHC 202 00

Controlling and Timing

Controlling the Module

Hardware inputs from the field can be used to:
 Increment/decrement the input counters with serial pulses from encoders or other square wave
sources.
 Set direction of count.
 Reset the outputs.
Hardware inputs from the field and software commands are used together to:
 Enable the count input.
Hardware inputs from the field or software commands can be used to:
 Preset the input counter to zero or maximum count.
Software commands can be used to:
 Configure the counters for pulse (tachometer) or quadrature mode.
 Configure for 16 or 32 bit counters, with or without output assertion.
 Configure the module to operate in either count or rate-sample mode.
 Option for outputs to operate or not operate if backplane bus communication is lost (i.e., a fault
condition).
 Option for outputs to switch on when setpoint and/or maximum values are reached.
 Define the setpoint and maximum count values.
 Define ON time for outputs.
 Disable outputs.
 Read the input counter totalizing or rate sample values.
 Retrieve the old (previous) input counter value after the counter has been preset.

278 35010574 12/2018

 140 EHC 202 00

Timing Diagrams
The following figure shows the EHC20200 timing diagrams.

Timing Parameter Table

The following table shows the EHC20200 timing parameters.

Timing Parameters Limits

Filter 200 Hz Filter 200 Hz No Filter
500 khz
Tdly1 Count to Output Assertion Delay (MAX) 4.8 ms 40 μs
Tdly2 Preset/Reset to Output Delay (MAX) 4.8 ms 40 μs
Tpw1 Count/Reset Pulse Width (MIN) 2.5 ms 1 μs
Tpw2 Preset Pulse Width (MIN) 2.5 ms 500 μs
Tst Enable/Reset/Preset to Count Setup Time (MIN) 2.5 ms 2 μs
Thold Enable/Reset to Count Hold Time (MIN) 2.5 ms 2 μs

NOTE: The timing parameter limits are measures at the module field terminal connector at the logic
low threshold level.

35010574 12/2018 279

140 EHC 202 00

Functions

COUNT UP
The input counter is reset to zero if the count direction input is UP and a preset (hardware or
software) or Load Value command is sent to the module.
When counting in the UP direction, the input counter increments to the maximum value, the next
input pulse sets the counter to zero and it continues counting back up to the maximum value.

COUNT DOWN
The input counter is set to maximum count if the count direction is down and a preset (hardware
or software) or Load Value command is sent to the module.
When counting in the DOWN direction, the input counter is decremented from the maximum value
to zero. The next pulse resets the input counter to the Maximum value and the increment down
starts again.

REMOVE ENABLE
This function disables the input counter, causing it to stop incrementing and hold the count
accumulated prior to disabling.

OUTPUTS
When configured in the count mode, outputs will turn on for defined times when setpoints or
maximum values have been reached.
No output assertion in two, 32 bit counter mode or rate sample.
Programmed ON time for outputs can be set for one channel, one output and one trigger point only.
In a running controller, latched outputs are turned off only by a hardware RESET input. If no reset
is provided, the outputs latched on will turn off when the controller is stopped.
OUTPUT COIL MODE available values:
 SETPOINT: ON when set point is reached, back to 0 automatically when the reference is
exceeded.
 LATCHED SETPOINT: ON when you reach the set point, it remains ON until no hardware reset
applied (input).
 TERMINAL COUNT: ON when it exceeds the max.
 LATCHED TERMINAL: ON when it exceeds the max and will be maintained as long as no
hardware reset (input).
 TIMED SETPOINT: ON from a set point and held ON during a defined time.
 TIMED TERMINAL: ON when it exceeds the max and held ON for a defined time.

280 35010574 12/2018

 140 EHC 202 00

COUNTER PRESET
This is both a hardware and software function. In the event that both methods are used, the last
one executed has precedence.
An input counter will be automatically preset whenever a new maximum value or rate sample time
is loaded.

COUNTER ENABLE
Both hardware and software enables are required for an input counter to operate. An input counter
will be automatically software enabled whenever a new maximum value is loaded or a preset
(hardware or software) is sent to it.

RATE SAMPLE VALUE

The rate sample value is held and may be accessed during count operations. The value read is
from the last configured and completed rate sample interval.

QUADRATURE MODE
When the module is configured for quadrature mode operation, the counter requires encoder
pulses on inputs A and B.
In quadrature mode, all input signal edges are counted. A 60 count/revolution encoder will produce
a count of 240 for one shaft rotation.

35010574 12/2018 281

140 EHC 202 00

Operating Conditions and Examples

Rate Sample
rate sample, the module must be:
 Configured for pulse or quadrature mode.
 Configured for Rate Sample mode.
 Loaded with the Rate Sample time value.
 Enabled to count, using hardwired input and software control bits.

Pulse Count
Count pulses, the module must be:
 Configured for pulse or quadrature mode.
 Configured for counter display: two, 16 bit, one, 32 bit, or two, 32 bit counters.
 Loaded with the maximum count.
 Enabled to count, using hardwired input and software control bits.

Pulse Count and Turning Outputs On/Off

To count pulses and turn outputs on and off, the module must be:
 Configured for pulse or quadrature mode.
 Configured for two, 16 bit or one, 32 bit counter.
 Configured to assert or not assert outputs at the programmed count values when the module
loses communication with the bus (fault condition).
 Configured to specify if outputs turn on at a set point or maximum count, turn on at those points
for a specific amount of time, or remain latched. If latched, outputs can only be reset by a hard
wired input.
 Loaded with set point values, maximum count values, and output assert time.
 Enabled to count using hardwired input and software control bits.

OUTPUT COIL MODE available values

SETPOINT: ON when set point is reached, back to 0 automatically when the reference is
exceeded.
LATCHED SETPOINT: ON when you reach the set point, it remains ON until no hardware reset
applied (input).
TERMINAL COUNT: ON when it exceeds the max.
LATCHED TERMINAL: ON when it exceeds the max and will be maintained as long as no
hardware reset (input).
TIMED SETPOINT: ON from a set point and held ON during a defined time.
TIMED TERMINAL: ON when it exceeds the max and held ON for a defined time.

282 35010574 12/2018

 140 EHC 202 00

Counter Rollover Examples for Pulse Input

The following figure is an example of a counter rollover with pulse input, counting up.

Count is from 0 -> 10 (Maximum Count)

Output A turns on at Setpoint = 5
Output B turns on after Input Count = Maximum (Terminal) Count = 10
The following figure is an example of a counter rollover with pulse input, counting down.

Count is from 10 (Maximum Count) -> 0

Output A turns on at Setpoint = 5
Output B turns on after Input Count = 0
NOTE: Outputs are not latched.

35010574 12/2018 283

140 EHC 202 00

Counter Rollover Examples for Quadrature Input

The following figure is an example of a counter rollover with quadrature input, counting up.

Count is from 0 -> 10 (Maximum Count)

Output A turns on at Setpoint = 5
Output B turns on after Input Count = Maximum (Terminal) Count = 10
The following figure is an example of a counter rollover with quadrature input, counting down.

Count is from 10 (Maximum Count) -> 0

Output A turns on at Setpoint = 5
Output B turns on after Input Count = 0
NOTE: Outputs are not latched.

284 35010574 12/2018

 140 EHC 202 00

Addressing

Flat Addressing
The 140EHC20200 high speed counter requires six contiguous 16-bit input words (%IW) and six
contiguous 16-bit output words (%QW).

Topological Addressing

Point I/O Object Comment

Input 1 %IW[\b.e\]r.m.1.1 Data
•••
Input 6 %IW[\b.e\]r.m.1.6 Data
Output 1 %QW[\b.e\]r.m.1.1 Data
•••
Output 6 %QW[\b.e\]r.m.1.6 Data

where:
 b = bus
 e = equipment (drop)
 r = rack
 m = module slot

35010574 12/2018 285

140 EHC 202 00

I/O Map and Commands

Overview
The 140 EHC 202 00 high speed counter requires six contiguous output (4X) and six contiguous
input (3X) registers in the I/O map.
The 4X registers perform the same configuration tasks as in the Parameter Configuration. Also,
the preset and the enable inputs connected to the field wiring terminal block perform the same
functions as those software command control bits. When both methods are used to:
 Preset a counter – the last preset executed has precedence.
 Enable/disable a counter – it will only be enabled when both the hardware enable input and
software enable control bit are in the enable state.
For simple applications, the parameter configuation rather than the I/O mapped registers can be
used to configure the module. Parameter configuration is only possible while the PLC is stopped.
The selected parameters take effect when the PLC is set to run. For applications that require that
module parameters be changed while the system is running, user logic can modify the I/O map-
assigned registers to override the previously selected parameters.
When using either parameter configuration or I/O map registers, the maximum values specified in
the Load Values Command section are the largest values that can be used by the module.
The I/O Mapped registers discussed in this section are 4X output registers that:
 Preset and enable/disable input counters.
 Load setpoint and maximum values to define output turn on points.
 Set mode of operation, count, or rate sample.
 Enable output switches and configures their mode of operation.
3X input registers that:
 Hold count or rate sample data.
 Display field power status.
 Echo 4X command data after the command is executed by the module.

Commands
There are four command that can be performed. Each uses one or more of both types of registers
assigned to the module. In addition to the command definition byte, the first 4X register for all
commands contain control bits to preset and enable/disable counters of either channel.

286 35010574 12/2018

 140 EHC 202 00

Command 1 - CONFIGURES
Command 1 uses three 4X registers and six 3X registers (see below).
The following figure shows the 4X and 3X registers for command 1.

This command does the following:

 Sets up the module for pulse or quadrature input.
 Sets up the module for count or rate-sample mode. Counters cannot be separately configured.
 Defines counter register length – 16 or 32 bit.
 Enables output assertion including module communication loss state. Output assertion is
available if configured for 2, 16 bit, or 1, 32 bit counter. No output assertion is available if 2, 32
bit counters are defined, or in rate-sample mode.
 Defines output assertion point.

Command 2 - LOADS VALUES

There are four formats for this command. It uses up to six 4X registers and six 3X registers.
The following figure shows the format for registers 4X and 3X for command 2.

Values loaded may be the following.

 Maximum count and setpoint (i.e., output turn on times).
 Output assertion ON time duration (one input only).
 Rate sample time interval.

35010574 12/2018 287

140 EHC 202 00

Command 3 - READ INPUT COUNTER

Command 3 uses one 4X register and six 3X registers (see below).
The following figure shows the 4X and 3X registers for command 3.

Command 4 READS RATE SAMPLE or LAST INPUT COUNT BEFORE PRESET

Command 4 uses one 4X register and six 3X registers (see below).
The following figure shows the 4X and 3X registers for command 4.

NOTE: 4X register formats for the commands are described first. The 3X register contents after
issuing Command 1 or 2 are listed after the 4X register description for Command 2, since the
responses are the same for both. The 3X responses for Commands 3 and 4 immediately follow
those commands.
NOTE: When Command 0 (4X = 00XX) or any other undefined commands are asserted in the 4X
register, the 3X registers will contain the count inputs if in count mode (same as Command 3) and
the rate sample values when in rate-sample mode (same as Command 4).

Command Words Described

The following details the command words and responses.

288 35010574 12/2018

 140 EHC 202 00

Command 1 - CONFIGURE, Output Register Format (4X = 01XX hex)

The following figure shows the 4x output register for command 1.

The following figure shows the 4x + 1 output register for command 1 (4X+1).

35010574 12/2018 289

140 EHC 202 00

The following figure shows the 4x +2 output register for command 1.

NOTE: The Output ON time specified in the Command 2 registers may be used by only one of the
four outputs. When more than one output is set to mode 5 or 6, the module firmware will operate
the first one encountered, and disable the other outputs set to modes 5 or 6.

Command 2. LOAD VALUES, Output Register Format (4X = 02XX hex)

The LOAD VALUES 4X register format depends on the Counter/Rate Sample mode selected in
Command 1, Register 4X+1, bits 11 and 12.

290 35010574 12/2018

 140 EHC 202 00

Two 16 Bit Counters

If configured for two, 16 bit Counters - Output Assert ON, the following information is displayed.
The following figures show the counters for registers 4X through 4X+5 modules.

NOTE: Zero set into any 4X register means no change.

35010574 12/2018 291

140 EHC 202 00

One 32 Bit Counter

If configured for one, 32 bit Counter - Output Assert ON, the following information is displayed.
The following figure shows the counters for registers 4X through 4X+5, with low and high word.

NOTE: Zero set into any 4X register pair for 32 bit values or any 4X register means no change.

292 35010574 12/2018

 140 EHC 202 00

Two 32 Bit Counters

If configured for 2, 32 bit Counters - NO Output Assert, the following information is displayed.
The following figures show the 4X through 4X+4 counters, with low and high word.

NOTE: Zero set into any 4X register pair for 32 bit values or any 4X register means no change.

35010574 12/2018 293

140 EHC 202 00

Rate Sample Mode

If configured for Rate Sample Mode, the following information is displayed.
The following figure shows the 4X through 4X+2 counters.

NOTE: Zero set into any 4X register or any 4X register pair for 32 bit values means no change.

294 35010574 12/2018

 140 EHC 202 00

Command 1 and Command 2 Response Formats

The following figures show the 3X through 3X+5 response formats.

Command 3, READ INPUT COUNTER, Output Register Format (4X = 03XX hex)
The following figure shows the 4X register for command 3.

35010574 12/2018 295

140 EHC 202 00

Command 3 Response Format

The following figure shows the command 3 response format.

Command 4, READ RATE SAMPLE or READ LAST COUNT VALUE BEFORE MOST RECENT PRESET,
Output Register Format (4X = 04XX hex)
The following figure shows the 4x counters for command 4.

296 35010574 12/2018

 140 EHC 202 00

Command 4 Response Format

The following figures show the counters for 3X through 3X+5 for command 4.

I/O Map Status Byte

The most significant bit in the I/O Map status byte is used for the 140 EHC 202 00 High Speed
Counter Module.
The following figure shows the map status byte register.

COUNT UP Example
Field connections for this example are illustrated in the EHC 202 wiring diagrams 1-4. The
maximum allowable Vref value is 30 VDC. Input pulse on-off threshold levels for the 5 ... 24 VDC
Vref range are listed in the module specification table. The minimum differential input is 1.8 V.
The following user logic:
 Configures the module to count up from zero.
 Turns an output on for one count at a setpoint value of 50.
 Continues counting to 100.
 Rolls over to zero and turn on a second output for one count.
 Repeats the operation.

35010574 12/2018 297

140 EHC 202 00

The following table shows the I/O Map register assignments.

Input Ref Output Ref

300001-300006 400001-400006

In this example, block moves are used to load the operating parameters into the module. This
requires pre-defined tables be established. Register values are in HEX format.

Module Configuration Table

The following table shows the module configurations.

400101 0140 CONFIGURE command, Disable Counter 2

400102 0000 Pulse input, two 16 bit counters, output assert on Rate Sample OFF,
disable outputs at bus communication loss
400103 3100 Output 1A on at setpoint, Output 1B on at maximum count +1
Output 2A and 2B are disabled
400104 0000
Not used by this command
400105 0000
400106 0000

Load Values Table

The following table shows the load values.

400201 0243 LOAD VALUES command, disable Counter 2, preset and enable
Counter 1
400202 0064 Counter 1 maximum count, count after which Output 1B turns on
400203 0032 Counter 1 setpoint, count when Output 1A turns on
400204 0000 Counter 2 maximum count (not used in this example)
400205 0000 Counter 2 setpoint (not used in this example)
400206 0000 Output assert time (Not used in this example, one output only, fused

Zeros in the 4X registers also mean no change. Setpoint, maximum count and assert time can only
be set to zero using the parameter configuration. When the registers in this example are echoed,
zeros will appear but the actual content in the module will be unchanged from previous values. In
this example, Counter 2 is disabled and its outputs and timed assert have not been selected.
Registers 400204 - 6 have no meaning.
After the module executes the Configure and Load Value’s commands, they are echoed in the I/O
mapped 3X registers except for the command register’s low 8 bits. Command execution time by
the module is 1 ms. Actual time between the 4X register block move and the echo response display
in the 3X registers is dependent on User Logic and hardware configuration. An echo of the
Configuration command registers would appear as follows:

298 35010574 12/2018

 140 EHC 202 00

Response Table
The following table shows the echo response for the configuration command.

Register Value
300001 0100
300002 0000
300003 3100
300004 0000
300005 0000
300006 0000

Read Input Counter Table

The following table shows the read input registers.

40301 0300 READ INPUT COUNTER command

40302 0000
40303 0000
Not used by this command
40304 0000
40305 0000
40306 0000

When this command is issued, the content of the input pulse counter is retrieved. The 3X register
content would appear as follows:

Response table
The following table shows the content of the registers.

Register Value Description

300001 0300 Command echo
300002 XXXX Current input count
300003 0000 Zeros as the count will not exceed 100. For counts above 65,536,
this register is a multiplier. As an example: 30002 has a value of
324 and 30003 a value of 3.The total count is (65,536 x 3) + 324
= 196,932
300004 0000 Counter 2 is disabled
300005 0000 Counter 2 is disabled
300006 0X00 X is the field power indicator

35010574 12/2018 299

140 EHC 202 00

Reset of Latched Outputs

If register 400103 in the Module Configuration Table has been set to 4200, Output 1A would have
been latched on at setpoint and Output 1B latched on at maximum count. Wiring Diagrams 2 and
4 show how the encoder Z outputs could be used to reset the latched outputs. The minimum pulse
width to reset outputs is 1 ms.

COUNT DOWN Example

The COUNT DOWN example uses the same wiring as in the count up example, except the Input
1B+ level is changed to common (connected to Vref-) for Pulse Inputs illustrated in Wiring
Diagrams 1 and 2. For Quadrature Inputs, no wiring change is required as the count direction is
decoded internally by sensing the phase shift change between inputs A and B.
The User Logic is the same as for the count example. The actual operation of the module is
different in that the output associated with maximum count turns on after zero count has been
reached.
The example configures the module to decrement the input count from the maximum value, turn
on an output at a setpoint value of 50, and turn on a second output after the input counter had
reached zero and rolled over to the maximum count; the operation is then repeated. The initial
loading of the maximum count will not cause its associated output to turn on.

RATE SAMPLE Example for Either Pulse or Quadrature Input

Field connections for this example are illustrated in the Wiring Diagrams1-4. The connections on
terminals 15 and 16 are optional, depending on the use requirements of the outputs. Terminals 39
and 40 always require the 24 VDC supply connections. The maximum allowable Vref value is 30
VDC. Input pulse on-off threshold levels for the 5 ... 24 VDC Vref range are listed in the module
specification table. The minimum differential input is 1.8 V.
As with count examples, tables are set up and transferred to the module using block moves. The
User Logic for Rate Sample is the same as that used for Pulse Input Count Up/Down.

Module Configuration Table

The following table shows the module configurations.

400101 0140 CONFIGURE command, Disable Counter 2

400102 1000 Pulse input, Rate Sample ON, disable outputs at bus
communication loss (Note: Bits 11 and 12 were not required.)
400103 0000
400104 0000
Not used by this command
400105 0000
400106 0000

300 35010574 12/2018

 140 EHC 202 00

Load Values Table

The following table shows the load values.

400201 0243 LOAD VALUES command, disable Counter 2, preset and enable
Counter 1
400202 XXXX Counter 1 Rate Sample Time in milliseconds
400203 0000 Counter 2 Rate Sample Time in milliseconds (Not used in this
example)
400204 0000 Not used by this command
400205 0000
400206 0000

NOTE: Command echoes are the same as described in the Pulse Input Count Up/Down examples.

Read Rate Sample Table

The following table shows a read rate sample.

400301 0400 READ INPUT COUNTER command

400302 0000
400303 0000
Not used by this command
400304 0000
400305 0000
400306 0000

When this command is issued, the input pulse counter content is retrieved. The 3X register content
is the count over the time period selected in the Load Values registers 4X + 1 and 4X + 2. The 3X
response to the Read-Rate Sample command in register 40301 is as follows.

Response Table
The following table shows the responses to the read rate sample command.

Register Value Description

300001 0400 Command echo
300002 XXXX Counter 1 Input rate low word
300003 XXXX Counter 1 Input rate high word: this register is a multiplier. As an
example: 30002 has a value of 324 and 30003 a value of 3.The
total count is (65,536 x 3) + 324 = 196,932
300004 0000 Counter 2 is disabled
300005 0000 Counter 2 is disabled
300006 0X00 X is the field power indicator

35010574 12/2018 301

140 EHC 202 00

Rate Sample Mode

NOTE: If a version 02.00 or higher module replaces a module which has a version number less
than 02.00 in a Rate Sample mode application, extra software configuration may be required.
Rate Sample mode is set using Command 1, CONFIGURE (01XX), 4X+1 register, bit 13 = 1 (see
the description of Command 1 in this section).
To verify the version of the module, reference the indicated label found on the top front of the
module.
The following figure shows the module’s label.

In modules prior to V02.00, when Rate Sample mode was selected, input was always handled as
if it were generated by a pulse encoder. For example, 60 count per revolution encoders, either
pulse or quadrature types, would give a rate of 60 for a one-second revolution when the interval
was set for one second.
NOTE: Beginning with V2.00 modules, if a quadrature type encoder is used to provide count input
and Pulse/Quadrature Input Counter 1 and 2, bits 9 or 10, are set to 1, the module will detect all
edges.
The result is four times the rate sample value as would be accumulated with an equivalent pulse
encoder input. In the example in the above paragraph, the rate sample would be equal to 240.
Encoder type selection is set using Command 1, CONFIGURE (01XX), 4X+1 register, bits 9 or 10
(see the description of Command 1 in this section).
If the Encoder Type select bits are set to 0, either type of encoder will produce the Rate Sample,
as did versions of the module that were lower than V02.00.

302 35010574 12/2018

 140 EHC 202 00

Indicators

Illustration
The following figure shows the LED indicators for the EHC20200 High Speed Counter module.

Descriptions
The following table shows the LED descriptions for the EHC 202 00 high speed counter.

LEDs Color Indication when On

Active Green Bus communication is present
F Red Indicates internal fuse blown or loss of output power supply
In 1 Green Counter 1 input
En 1 Green Enable Counter 1 input
Pre C1 Green Preset Counter 1 input
Res 01 Green Reset Output 1A, 1B
In 2 Green Counter 2 input
En 2 Green Enable Counter 2 input
Pre C2 Green Preset Counter 2 input
Res 02 Green Reset Output 2A, 2B
Out 1A Green Counter 1A output
Out 1B Green Counter 1B output
Out 2A Green Counter 2A output
Out 2B Green Counter 2B output

35010574 12/2018 303

140 EHC 202 00

Wiring

Signal overview
The following table shows the signal descriptions of the wiring diagram.

Parameter Description/Usage
INPUT A Single ended or differential count input or Phase A for quadrature mode.
Single ended (active low only) uses Input 1A+ and/or Input 2A+.
Input 1A- and/or Input 2A- are not connected. Differential input encoders use
both plus (+) and minus (-) inputs.
INPUT B Direction level for non-quadrature devices or Phase B for quadrature mode.
Direction inputs for non-quadrature input devices are: Count Up = High
Voltage Level; Count Down = Low Voltage Level
For single ended Input devices, only Input 1B+ and/or Input 2B+ are used.
Input 1B- and 2B- are not connected. Differential input encoders use both
plus (+) and minus (-) inputs.
PRESET C Presets count register(s). Low level causes preset.
For single ended Preset inputs, only Preset 1C+ and/or Preset 2B+ are
used. Preset 1C- and 2C- are not connected. Differential input encoders use
both plus (+) and minus (-) inputs.
OUTPUT RESET 0 Low level resets Outputs 1A, 1B, 2A, and 2B to OFF if latched.
For single ended Reset inputs, only Reset 10+ and/or Reset 20+ are used.
Reset 10- and 20- are not connected. Differential input encoders use both
plus (+) and minus (-) inputs.
ENABLE Low level enables counting.
For single ended Enable inputs, only Enable 1+ and/or Enable 2+ are used.
Enable 1- and 2- are not connected. Differential input encoders use both
plus (+) and minus (-) inputs.
VREF Field input device power source connection. Also, connect any unused (+)
inputs to the group VREF terminal or the one in use (30 Vdc max).
Group A = Terminal 17
Group B = Terminal 37
Group A and Group B VREF supplies can be different voltage levels.
LO FILTER SEL Enables the internal 200 Hz filter when connected to Return Terminal 39.
OUTPUT Internal FET switches connect the output supply wired to Terminal 40 to the
Output 1A, 1B, 2A, 2B terminals at output assert times.
POWER SUPPLY External 24 Vdc power supply (+) connection. Required for the module
interface and for Outputs 1A, 1B, 2A, and 2B.
RETURN External 24 Vdc power supply (-) connection. Required for the module
interface and for Outputs 1A, 1B, 2A, and 2B.

304 35010574 12/2018

 140 EHC 202 00

Miscellaneous Information
Field wire to Counter 2 inputs and outputs, when configured for one, 32 bit counter with output
assertion. The unused Counter 1 must have its + (plus) inputs connected to VREF+.
Input counts and parameters are not maintained in the module at power down. The rewrite of
parameters at power up must be done with either user logic or Modzoom-type preset panel
selections.
The 200 Hz filter for each counter can be activated by strapping the Lo Filter Sel terminal to the
Return terminal. This function provides noise immunity for low frequency applications and can also
be used for relay debounce.

35010574 12/2018 305

140 EHC 202 00

Wiring diagram 1
Basic wiring diagram showing single ended pulse input, counting up and constant enable.

NOTE: Terminal description:

 Terminal 1 Pulse encoder input (sinking device)
 Terminal 3 Input 1B count UP direction
 Terminal 5 Unused hardwire Preset tied high

306 35010574 12/2018

 140 EHC 202 00

 Terminal 7 Output Reset tied high, not required; outputs not used
 Terminal 11 Hardware enabled
 Terminal 15, 16 Outputs 1A and 1B operate relays
 Terminal 17 Required VRef+ connection
 Terminals 21, 23, 25, 27, 31, 37 Counter 2 not used. These terminals must be connected VRef+
 Terminal 39 Required Output Supply Return
 Terminal 40 Required Output Supply
 N/C not connected

35010574 12/2018 307

140 EHC 202 00

Wiring Diagram 2
Wiring diagram showing differential pulse input, counting up and constant enable.

NOTE: Zero pulse resets Output 1A and 1B

308 35010574 12/2018

 140 EHC 202 00

Wiring Diagram 3
Wiring diagram showing quadratur input with constant enable.

35010574 12/2018 309

140 EHC 202 00

Wiring Diagram 4
Wiring diagram showing differential quadrature input with constant enable.

NOTE: Zero pulse resets Output 1A and 1B

310 35010574 12/2018

 140 EHC 202 00

Maintenance

Fuses
Fuses

Internal 2.5 (P/N 043503948 or equivalent)

External user discretion

Fuse Location Figure

The following figure shows the locations of the fuses for the EHC 202 module..

NOTE: Turn off power to the module and remove the field wiring terminal strip to gain access to
the fuse.

35010574 12/2018 311

140 EHC 202 00

Parameter Configuration

Overview
This section provides information on the parameters, accessible in the Parameter Configuration
Screen.

Parameter Configuration Default Screen

This diagram shows the Parameter Configuration default screen

312 35010574 12/2018

 140 EHC 202 00

Addressing and Task

This table shows the parameters for addressing and task with its values

Name Value Options

MAPPING WORD -
INPUTS STARTING ADDRESS 1 0-100000
INPUTS ENDING ADDRESS 6 -
OUTPUTS STARTING ADDRESS 1 0-100000
OUTPUTS ENDING ADDRESS 6 -
TASK MAST FAST
(Grayed if module in other than local) AUX0
AUX1
AUX2
AUX3

NUMBER OF COUNTERS
This part of the parameter configuration screen depends on the choice made in the field: NUMBER
OF COUNTERS. Therefore you find four tables accordingly.
This table shows the parameters configuration screen for the entry: 2x16 WITH OUTPUT

Name Value Options

NUMBER OF COUNTERS 2x16 WITH OUTPUT 1x32 WITH OUTPUT
1x32 NO OUTPUT
RATE SAMPLE MODE
COUNTER 1 MODE CONTROL QUADRATURE INCREMENTAL
COUNTER 2 MODE CONTROL QUADRATURE INCREMENTAL
OUTPUT COIL 1A MODE SET POINT TIMED SET POINT
LATCHED SET POINT
OUTPUT COIL 1B MODE
TERMINAL COUNT
OUTPUT COIL 2A MODE LATCHED TERMINAL
OUTPUT COIL 2B MODE TIMED TERMINAL

COUNTER 1 MAX COUNT 0 0-65535

COUNTER 1 SET POINT
COUNTER 2 MAX COUNT
COUNTER 2 SET POINT
TIME OUTPUT ON

35010574 12/2018 313

140 EHC 202 00

This table shows the parameters configuration screen for the entry: 1x32 WITH OUTPUT

Name Value Options

NUMBER OF COUNTERS 1x32 WITH OUTPUT 2x16 WITH OUTPUT
1x32 NO OUTPUT
RATE SAMPLE MODE
COUNTER 2 MODE CONTROL QUADRATURE INCREMENTAL
OUTPUT COIL 2A MODE SET POINT TIMED SET POINT
LATCHED SET POINT
OUTPUT COIL 2B MODE
TERMINAL COUNT
LATCHED TERMINAL
TIMED TERMINAL
COUNTER 2 MAX COUNT: LOW 0 0-65535
WORD
COUNTER 2 MAX COUNT: HIGH
WORD
COUNTER 2 SET POINT: LOW
WORD
COUNTER 2 SET POINT: HIGH
WORD
TIME OUTPUT ON

This table shows the parameters configuration screen for the entry: 1x32 NO OUTPUT

Name Value Options

NUMBER OF COUNTERS 1x32 NO OUTPUT 2x16 WITH OUTPUT
1x32 WITH OUTPUT
RATE SAMPLE MODE
COUNTER 1 MODE CONTROL QUADRATURE INCREMENTAL
COUNTER 2 MODE CONTROL QUADRATURE INCREMENTAL
COUNTER 1 SET POINT: LOW 0 0-65535
WORD
COUNTER 1 SET POINT: HIGH
WORD
COUNTER 2 SET POINT: LOW
WORD
COUNTER 2 SET POINT: HIGH
WORD

314 35010574 12/2018

 140 EHC 202 00

This table shows the parameters configuration screen for the entry: RATE SAMPLE MODE

Name Value Options

NUMBER OF COUNTERS RATE SAMPLE MODE 2x16 WITH OUTPUT
1x32 WITH OUTPUT
1x32 NO OUTPUT
COUNTER 1 MODE CONTROL QUADRATURE INCREMENTAL
COUNTER 2 MODE CONTROL QUADRATURE INCREMENTAL
COUNTER 1 RATE SAMPLER 0 0-65535
TIMER
COUNTER 2 RATE SAMPLER
TIMER

35010574 12/2018 315

140 EHC 202 00

316 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
140 EHC 105 00
35010574 12/2018

Chapter 30
140 EHC 105 00: High Speed Counter Module

140 EHC 105 00: High Speed Counter Module

Purpose
The following chapter provides information of the Quantum 140 EHC 105 00 High Speed Counter
Module.

What Is in This Chapter?

This chapter contains the following topics:
Topic Page
Presentation 318
Specifications 320
Indicators 322
Wiring 323
Parameter Configuration 326

35010574 12/2018 317

140 EHC 105 00

Presentation

Function
The 140 EHC 105 00 is a highspeed counter module. It utilizes five equivalent, independently
usable counters with the following functions:
 32bit event counter with 6 modes
 Event counter with parallel set point output activation
 Event counter with parallel set point output activation and fast Final Set Point
 Event counter with serial set point activation
 Event counter with serial set point activation and fast final set point
 Event counter with timed set point output activation
 Event counter with latched set point output avtivation

 32bit differential counter (2 configurable counter pairs) with 2 modes

 Differential counter with serial set point output activation
 Differential counter with parallel set point output activation

 16bit repetitive counter

 32bit (velocity counter, rate counter) with 2 modes
 Rate counter with 100ms gate time
 Rate counter with 1s gate time

318 35010574 12/2018

 140 EHC 105 00

Illustration
The following figure shows the EHC 105 module and its components.

1 Model Number, Module Description, Color Code

2 LED Display
3 Fuse Cutouts
4 Field Wiring Terminal Strip
5 Removable Door
6 Customer Identification Label (Fold label and place it inside door)

NOTE: The field wiring terminal strip (Modicon #140 XTS 002 00) must be ordered separately. (The
terminal strip includes the removable door and label.)

35010574 12/2018 319

140 EHC 105 00

Specifications

General Specifications
General Specifications

Module Type High Speed Counter Module

Number of Channels 5
External Power 19,2 ... 30 VDC, 24 VDC nominal, 60 mA required
plus the load current for each output.
Power Dissipation Maximum 6W
Bus Current required 250 mA
I/O Map 12 words IN, 13 words OUT
Isolation (channel to bus) 500 VAC rms for 1 minute
Fault detection Loss of output field power, output short circuit
Fusing internal: none
external: user discretion
Backplane Support Local, remote or distributed
Compatibility All Quantum Controllers, V2.0 at a minimum

NOTE: The 5Cx and 24Cx counter inputs may be used alternatively.

Counter Inputs
Counter Inputs

Counter Inputs 5V 24V

Count frequency 100 kHz 20 kHz
Count to output 3ms
assertion delay (Max)
Input voltage OFF state (VDC) :1,0 ... +1,15 OFF state (VDC): -3,0 ... +5,0
ON state (VDC): 3,1 ... 5,5 ON state (VDC):15,0 ... 30,0
Input current 8 mA for 3,1VDC 7 mA for 24 VDC
Duty cycle 1:1
Data formats 16 bit counter: 65.535 Decimal
32 bit counter: 2.147.483.647 Decimal
Delay time (typical) t = 0,002 ms
Operating mode discrete incremental counter

320 35010574 12/2018

 140 EHC 105 00

Discrete Inputs
Discrete Inputs

Discrete Inputs 24V

VREF supply +24VDC Off State (VDC): -3,0 ... +5,0
ON State (VDC):15,0 ... 30,0
Delay time (typical)
IN1 ... IN6 ton = 2,2 ms, toff = 1 ms
IN7, IN8 ton = 0,006 ms, toff = 0,3 ms
Input current (typical) 5 mA

Input Threshold
Input Threshold

single ended mode 5 VREF DC -

12 VREF DC -
24 VREF DC -3 ... 5 V on state/15 ... 30 off state
differential mode -

Discrete Outputs
Discrete Outputs

Output Voltage 24V

FET Switch ON 20 ... 30 VDC
FET Switch OFF 0 VDC (ground reference)
Max load current (each output) 0,5 A
Output off state Leackage 0,1 mA max @ 30 VDC
Output on state voltage drop 1,5 VDC @ 0,5 A

35010574 12/2018 321

140 EHC 105 00

Indicators

Illustration
The following table shows the LED indicators for the EHC 105 module.

Description
The following table shows the LED descriptions for the EHC 105 module

LED Color Description

R green Module is READY (firmware initialization has been completed).
P green POWER - the US24 working voltage is present.
F red The red F-LED (F = fault) lights on the following faults:
 24 VDC supply voltage (US24) not present
 Short circuit on one of the OUTn outputs
 Pulse monitoring has tripped (indicate bit = 1 and ERRx = 1)
 Counter overflow (indicate bit = 0 and ERRx = 1)

ACTIVE green The PLC communication becomes active.

1 to 8 green Displays the signal states of the discrete inputs IN1...IN8.
1 to 8 green Displays the signal states of the discrete outputs OUT1...OUT8.
C1 to C5 green Lights with the clock frequency applied to clock-inputs 5C1 to
5C5 respectively 24C1 to 24C5.

322 35010574 12/2018

 140 EHC 105 00

Wiring

5Cx Counter Inputs

Wiring diagram for 5Cx counter inputs:

35010574 12/2018 323

140 EHC 105 00

24Cx Counter Inputs

Wiring diagram for 24Cx counter inputs:

324 35010574 12/2018

 140 EHC 105 00

Discrete Inputs and Outputs

Wiring diagram for discrete inputs and outputs:

35010574 12/2018 325

140 EHC 105 00

Parameter Configuration

Overview
This section provides information on the parameters, accessible in the Parameter Configuration
Screen.

326 35010574 12/2018

 140 EHC 105 00

Parameter Configuration Default Screen

This diagram shows the Parameter Configuration default screen

35010574 12/2018 327

140 EHC 105 00

Addressing and Task

This table shows the parameters for addressing and task with its values

Name Default Value Options

MAPPING WORD (%IW-3X%MW-4x) -
INPUTS STARTING ADDRESS 1 -
INPUTS ENDING ADDRESS 12 -
OUTPUTS STARTING ADDRESS 1 -
OUTPUTS ENDING ADDRESS 13 -
TASK MAST FAST
(Grayed if module in other than local) AUX0
AUX1
AUX2
AUX3

Counters
This table shows the parameters for the counters with its values

Name Default Value Options

COUNTER_1
COUNT INPUT SIGNAL ON NEGATIVE No Yes
TRANSITION
USE INPUT 1 FOR COUNTER ENABLE No Yes
WATCHDOG TIMER (0.1s) 0 0-255
OUTPUT SET POINT 1 0 0-65535
OUTPUT SET POINT 2 0 0-65535
INPUTS_COUNTER_START/RESTART LOGIC FUNCTION TO OR AND
START/RESTART
COUNTER
INPUT A 1 -
1-8
INPUT B - -
1-8
INPUT C - -
1-8
FREEZE_COUNTER_REGISTERS INPUT D 6 -
1-8
INPUT E - 1-8
INPUT F - 1-8

328 35010574 12/2018

 140 EHC 105 00

Name Default Value Options

OUTPUTS SETPOINT 1 LINKED TO - 1-8
OUTPUT
 INVERT OUTPUT No Yes
SETPOINT 2 LINKED TO 6 -
OUTPUT 1-8
 INVERT OUTPUT No Yes
FINAL SETPOINT LINKED 1 -
TO OUTPUT 1-8
 INVERT OUTPUT No Yes
TIMED FINAL SETPOINT - 1-8
LINKED TO OUTPUT
 INVERT OUTPUT No Yes
 PULSE WIDTH (x 0.02s) 0-255
COUNTER_2 See COUNTER_1
COUNTER_3
COUNTER_4
COUNTER_5

35010574 12/2018 329

140 EHC 105 00

330 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
Glossary
35010574 12/2018

Glossary

H
HTTP
A domain name given to a specific computer on a network and used to address that computer.

35010574 12/2018 331

Glossary

332 35010574 12/2018

 Quantum using EcoStruxure™ Control Expert
Index
35010574 12/2018

Index

0-9 C
140CRA21110, 99 channel data structure for analog modules
140CRA21120, 99 T_ANA_BI_VWE, 24, 26
140CRA21210, 99 T_ANA_IN_VE, 24, 25
140CRA21220, 99 T_ANA_IN_VWE, 24, 25
140CRA93100, 33 T_CNT_105, 24
140CRA93200, 33 configuring discrete I/O modules, 17
140CRP93100, 33 connector types, for fiber optic links, 73
140CRP93200, 33
140EHC10500, 261
140EHC20200, 261 E
140EIA92100, 249 error codes
140HLI34000, 261 140CRA93100, 51
140NOE211x0, 183 140CRA93200, 57
140NOE251x0, 183 140CRP93100, 38
140NOE31100, 183 140CRP93200, 44
140NOE35100, 183 140NOM21100, 147
140NOE77100, 183 140NOM21200, 159
140NOE77101, 183
140NOE77110, 183
140NOE77111, 183 F
140NOM21100, 137 fiber optic cable
140NOM21200, 137 connecting, 75, 94
140NOM25200, 137 termination kits, 73
140NRP95400, 33
general specifications, 76
140NRP95401C, 33 N
general specifications, 96 NOE771xx
140NWM10000, 183 run LED status, 242
NRP95400
bus topology, 67
A connecting, 75
addressing, 21, 285 hot standby systems example, 71
flat, 22 materials for fiber optic links, 72
IODDT, 24 point-to-point topology, 66
RIO topologies, 65
self-healing ring topology, 70
B termination kits, 73
bus topology, 67, 87 tree topology, 69

35010574 12/2018 333

Index

NRP95401C
bus topology, 87
compatibilty, 95
connecting, 94
hot standby systems example, 91
materials for fiber optic links, 92
point-to-point topology, 86
RIO topologies, 85
self-healing ring topology, 90
tree topology, 89

P
point-to-point topology, 66, 86

R
RIO fiber optic network
bus topology, 67, 87
point-to-point topology, 66, 86
self-healing ring topology, 70, 90
tree topology, 69, 89

S
self-healing ring topology, 70, 90
services
140NOE77100, 189
140NOE77101, 189
140NOE77110, 189
140NOE77111, 189
140NWM10000, 189
status bytes, 29

T
T_ANA_BI_VWE, 26
T_ANA_IN_VE, 25
T_ANA_IN_VWE, 25
T_CNT_105, 26
termination kits, 73
tree topology, 69, 89

334 35010574 12/2018