DATA SHEET
CONTROL MODULE
DESCRIPTION
The Control Module, P/N 55-042 & 55-047, provides a means to switch an external power supply to
notification appliances or release solenoids used for sprinkler operation, or to activate Fike’s Masterbox
Interface module, P/N 10-2413, which is used on a Local Energy Type Auxiliary Fire Alarm System. The
module is capable of Class A or Class B wiring. The device will monitor the wiring (while external power
is not switched to the auxiliary devices) to the connected device for open and short circuits via an end of
line resistor (Class B only). The module will monitor the external power input for loss of power (DC voltage
supplies only). The isolator version of the module, P/N 55-047, provides complete short circuit isolation for
installations requiring NFPA, Class X wiring.
The module is compatible with Fike’s CyberCat® and Cheetah® Xi intelligent control panels. Its operating
parameters are configured using the panel’s programming software and are stored within non-volatile RAM
in the module. This on-board intelligence allows each module to communicate its status directly to other APPROVALS:
devices connected to the panel. This peer-to-peer digital protocol results in less information that needs to be
sent between the module and the host control panel, resulting in faster, more reliable communication. • UL - S2203
• FM
• City of New York - 8-05-E
SPECIFICATIONS • CSFM - 7165-0900:0137
Normal Operating Voltage: 15 to 30 VDC
Standby Current: 630 uA max. average (continuous broadcasts)
Alarm Current: 2 mA (red LED on)
Maximum NAC Circuit Line Loss: 4 VDC
Power Supply Monitor: Regulated 24 VDC
Trouble Range: 0 to 2 VDC
Temperature Range: 32 to 120°F (0 to 49°C)
Humidity: 10 to 93% RH Non-condensing
Dimensions: 4.675”H x 4.275”W x 1.4”D
(119 mm H x 109 mm W x 36 mm D)
Accessories: 39kΩ End of Line Resistor P/N 10-2625 (included)
Wall cover plate (included)
Surface Mount Electrical Box: P/N 20-1347
Control Module Barrier: P/N 20-1346
Series Solenoid Diode/Resistor: P/N 10-2360
Mounting: Mounts directly on a 4-inch square electrical box with a
minimum depth of 2 1/8 inches. For surface mounting, use
20-1347 surface mount box.
OUTPUT RATING
Current Rating Maximum Voltage Load Description Application
2A 25 VAC PF=0.35 Non-Coded
3A 30 VDC Resistive Non-Coded
2A 30 VDC Resistive Coded
0.46A 30 VDC (L/R=20 ms) Non-Coded
0.7A 70.7 VAC PF=0.35 Non-Coded
0.9A 125 VDC Resistive Non-Coded
0.5A 125 VAC PF=0.75 Non-Coded
0.3A 125 VAC PF=0.35 Non-Coded
Form No. P.1.94.01-4
704 SW 10th Street P.O. Box 610 Blue Springs, Missouri 64013-0610 U.S.A.
Phone: 8162293405 www.fike.com
ORDERING INFORMATION
Fike P/N Description
55-042 Supervised Control Module - Non-isolator
55-047 Supervised Control Module - Isolator
Accessories
20-1346 Control Module Barrier
20-1347 Surface Mount Box
55-051 IR Tool
10-2360 Series Solenoid Diode/Resistor
10-2625 39K EOL
13-0192 COVERPLATE
MODULE DIMENSIONS
TERMINAL DEFINITIONS
T1 (+) SLC in/out T8 (+) 24 VDC External Power in/out
T2 (-) SLC in/out T9 (-) 24 VDC External Power in/out
T3 (+) SLC in/out T10 (+) 24 VDC External Power in/out
T4 (-) SLC in/out T11 NAC (+) Class A/B
T5 No Connection T12 NAC (-) Class A/B
T6 No Connection T13 NAC (-) Class A
T7 (-) 24 VDC External Power in/out T14 NAC (+) Class A
Copyright © Fike Corporation All Rights Reserved. Specifications are subject to change without notice. 2 of 2
Form No. P.1.94.01-4, March 2014. This document shall not be used for installation purposes. Please refer to installation instructions applicable for each product.
